After ng, dome barrel must not be less th8n 1/2" thick, nor flange for cap less then 11/16" thick,...

20

Transcript of After ng, dome barrel must not be less th8n 1/2" thick, nor flange for cap less then 11/16" thick,...

Page 1: After ng, dome barrel must not be less th8n 1/2" thick, nor flange for cap less then 11/16" thick, end these minimum dinensions must be shown on all done and toiler drawings covering
Page 2: After ng, dome barrel must not be less th8n 1/2" thick, nor flange for cap less then 11/16" thick, end these minimum dinensions must be shown on all done and toiler drawings covering
Page 3: After ng, dome barrel must not be less th8n 1/2" thick, nor flange for cap less then 11/16" thick, end these minimum dinensions must be shown on all done and toiler drawings covering
Page 4: After ng, dome barrel must not be less th8n 1/2" thick, nor flange for cap less then 11/16" thick, end these minimum dinensions must be shown on all done and toiler drawings covering
Page 5: After ng, dome barrel must not be less th8n 1/2" thick, nor flange for cap less then 11/16" thick, end these minimum dinensions must be shown on all done and toiler drawings covering
Page 6: After ng, dome barrel must not be less th8n 1/2" thick, nor flange for cap less then 11/16" thick, end these minimum dinensions must be shown on all done and toiler drawings covering
Page 7: After ng, dome barrel must not be less th8n 1/2" thick, nor flange for cap less then 11/16" thick, end these minimum dinensions must be shown on all done and toiler drawings covering
Page 8: After ng, dome barrel must not be less th8n 1/2" thick, nor flange for cap less then 11/16" thick, end these minimum dinensions must be shown on all done and toiler drawings covering
Page 9: After ng, dome barrel must not be less th8n 1/2" thick, nor flange for cap less then 11/16" thick, end these minimum dinensions must be shown on all done and toiler drawings covering
Page 10: After ng, dome barrel must not be less th8n 1/2" thick, nor flange for cap less then 11/16" thick, end these minimum dinensions must be shown on all done and toiler drawings covering
Page 11: After ng, dome barrel must not be less th8n 1/2" thick, nor flange for cap less then 11/16" thick, end these minimum dinensions must be shown on all done and toiler drawings covering
Page 12: After ng, dome barrel must not be less th8n 1/2" thick, nor flange for cap less then 11/16" thick, end these minimum dinensions must be shown on all done and toiler drawings covering
Page 13: After ng, dome barrel must not be less th8n 1/2" thick, nor flange for cap less then 11/16" thick, end these minimum dinensions must be shown on all done and toiler drawings covering
Page 14: After ng, dome barrel must not be less th8n 1/2" thick, nor flange for cap less then 11/16" thick, end these minimum dinensions must be shown on all done and toiler drawings covering
Page 15: After ng, dome barrel must not be less th8n 1/2" thick, nor flange for cap less then 11/16" thick, end these minimum dinensions must be shown on all done and toiler drawings covering
Page 16: After ng, dome barrel must not be less th8n 1/2" thick, nor flange for cap less then 11/16" thick, end these minimum dinensions must be shown on all done and toiler drawings covering
Page 17: After ng, dome barrel must not be less th8n 1/2" thick, nor flange for cap less then 11/16" thick, end these minimum dinensions must be shown on all done and toiler drawings covering
Page 18: After ng, dome barrel must not be less th8n 1/2" thick, nor flange for cap less then 11/16" thick, end these minimum dinensions must be shown on all done and toiler drawings covering
Page 19: After ng, dome barrel must not be less th8n 1/2" thick, nor flange for cap less then 11/16" thick, end these minimum dinensions must be shown on all done and toiler drawings covering
Page 20: After ng, dome barrel must not be less th8n 1/2" thick, nor flange for cap less then 11/16" thick, end these minimum dinensions must be shown on all done and toiler drawings covering