AEC-6910 en-50155 Test Report

8/10/2019 AEC-6910 en-50155 Test Report

1/29


2/29

R/N:Page: 2 of 68

Index

ItemTest

DescriptionReference

Date of Test(D/M/Y)

Result Location of Test Page

A. Characteristic Tests

A-1 Visual inspection EN 50155:2001, 10.2.1 PASS AAEON LAB 3

A-2Performance Test(where applicable)

EN 50155:2001, 10.2.2 Supply variations: 0,7 UPASS Cerpass 3

A-3 Insulation test EN 50155:2001, 10.2.9.1 500 V DC PASS Cerpass 3

A-4Voltage withstandtest

EN 50155:2001, 10.2.9.2 1000 Vrms, sinusoidalPASS Cerpass 3

B. Environmental Tests

B-1 Cooling testEN 50155:2001, 10.2.3EN60068-2-1, Ad

Ambient temperature: TX:Internal cubicleTemp 0~+55

PASS AAEON LAB 3

B-2 Dry heat testEN 50155:2001, 10.2.4EN60068-2-2, Bd

PASS AAEON LAB 4

B-3Vibration, Shock,and Bump test

EN50155:2001, 10.2.11EN 61373

PASS King Design 5

B-4 Damp heat testcyclic

EN50155:2001, 10.2.5EN 60068-2-30, Db

+25C/+55C @ 2 x 24h,2cycles

PASS AAEON LAB 11

C. EMC Tests

C-3Conductedemission

EN 50155:2001, 10.2.8.2EN 50121-3-2 (Table 4)EN 55011

79 dBV QP @ 150 - 500 kHz73 dBV QP @ 500 kHz - 5 MHz73 dBV QP @ 5MHz - 30 MHz

PASSCOMPLIANCELAB

12

C-4 Radiated emission

EN 50155:2001, 10.2.8.2EN 50121-3-2(Table 6)EN 55011

40 dBV/m QP @ 30 230kHz,10m47 dBV/m QP @ 230-1GHz,10m

PASSCOMPLIANCELAB

15

C-5Fast transient burstimmunity

EN 50155:2001, 10.2.7EN 50121-3-2 (Table 8)EN 61000-4-4

2 kV (capacitive clamp)

PC = A PASSCOMPLIANCELAB

20

C-6 Surge immunityEN 50155:2001, 10.2.6.2EN 50121-3-2 (Table 7)

1,8 kV, 5/50 us

2 Kv

PC = B

PASSCOMPLIANCELAB

22

C-7RFI immunity,Conducted

EN 50155:2001, 10.2.8.1EN 50121-3-2 (Table 7)EN 61000-4-6

10Vrms @ 0.15 - 80 MHz, 80 %AM (1 kHz)PC = A

PASSCOMPLIANCELAB

24

C-8RFI immunity,radiated

EN 50155:2001, 10.2.8.1EN 50121-3-2 (Table 9)EN 61000-4-3

10 V/m @ 80 - 1000 MHz, 80 %AM (1 kHz)PC = A

PASSCOMPLIANCELAB

26

C-9Electrostaticdischarge

EN 50155:2001, 10.2.6.4EN 50121-3-2 (Table 9)EN 61000-4-2

6 kV contact discharge

8 kV air discharge

PC = B

PASSCOMPLIANCELAB

28


3/29

R/N:Page: 3 of 68

A. Characteristic Tests

A-1 Visual inspectionA-1-1 Inspection Request

The visual inspection shall be carrier out to ensure that the equipment is of sound construction and, so far

as can be ascertained, meets its specified requirements.A-1-2 Inspection Result

Pass:This is a FAN less product, therefore without any noise leakage except the Hard Disk Driver motor.

A-2 Performance Test (where applicable)A-2-1 Test Condition

1. Supply variations:- Supply voltage: (1) rated input voltage x 0.7 (2) rated input voltage x 1.25- Operation function shall be worked normally at the supply variations.

2. Supply interruption:- Supply voltage: rated input voltage.- Interruption classification: Class S1.- Repeated 10 times at random and covered all modes of operation.

- Operation function shall be worked normally at supply variations.A-2-2 Test Result

1. Supply variations:

Test voltage (V) Result / Observation

DC 23.75 No malfunction

DC 13.3 No malfunction

2. Supply interruption:


DC 19 No malfunction

A-3 Insulation testA-3-1 Test Condition

- Test voltage: 500 Vdc.- No fundamental deterioration from the initial measurement.- Test voltage is applied between the power supply sides of external power adaptor and I/O ports

equipment under test.

A-3-2 Test Result


DC 500 No fundamental deterioration

A-4 Voltage withstand testA-4-1 Test Condition

- Test voltage: 1000 Vac or 1414Vdc.- Test time: one minute.- Neither disruptive discharge nor flashover shall occur.- Test voltage is applied between the power supply sides of external power adaptor and I/O ports

equipment under test.

A-4-2 Test Result


DC 1414 No disruptive discharge / no flashover

B. Environmental TestsB-1 Cooling test

B-1-1 Test EquipmentProgrammable Temperature & Humidity ChamberK.SON. INS. TECH. CORP.Model: TS-F3L+-100

Date of Calibration: 04/01/05


4/29

R/N:Page: 4 of 68

Serial Number: 1467

B-1-2 Test Condition

1. Test Temperature: 02. Test Times: 96Hrs3. Test Software: Windows 2000 / Run PassMark Burn In Test Pro 4.0

B-1-3 Machine Curve

B-1-4 Test Result

The system structure doesnt have any deformation; All functions are passed after low temperature

operation test.

B-2. Dry heat test

B-2-1 Test EquipmentProgrammable Temperature & Humidity ChamberK.SON. INS. TECH. CORP.Model: TS-F3L+-100

Date of Calibration: 04/01/05Serial Number: 1467


1. Test Temperature: 552. Test Times: 96Hrs3. Test Software: Windows 2000 / Run PassMark Burn In Test Pro 4.0

B-2-3 Machine Curve


5/29

R/N:Page: 5 of 68

B-2-4 Test ResultThe system structure doesnt have any deformation; All functions are passed after high temperature

operation test.

B-3 Vibration, Shock, and Bump testB-3-1 Test Equipment

SHOCK TEST

EQUIPMENT MFR MODELSERIAL

NUMBER

CAL.

DUE

Shock Testing System King Design KD-DP-1200-60 KDS11054989 No Cal. Required

Controller King Design KD-1200-03 KD674 No Cal. Required

Accelerometer B&K B&K 4398 2209043 No Cal. Required

VIBRATION TEST


NUMBER

CAL.

DUE

Vibration Tester King DesignKD-9363EM-600F2K-

50N120KDS11054783 No Cal. Required

Controller DACTRON FRONT-End Box 5250251 No Cal. Required

Control Accelerometer Wilcoxon Research WR-77 4208 No Cal. Required

B-3-2 Shock Test ConditionTemperature : 202

Humidity : 7020%RHEUT : AEC-6910 with HDDWave From : Half sine wave(operation)Acceleration : 30gDuration Time : 18msNo. of Shock : Each axis 3 timesShock of direction : X, Y, Z axis


6/29

R/N:Page: 6 of 68

B-3-3 Shock Test Photograph of test setup


7/29

R/N:Page: 7 of 68

B-3-4 Shock Test Curve


8/29

R/N:Page: 8 of 68

B-3-5 Shock Test Result

B-3-6 Vibration Test Condition

Temperature : 202

Humidity : 7020%RH


9/29

R/N:Page: 9 of 68

EUT : AEC-6910 with HDDWave From : Random vibration test(operation)

Test Axis : VerticalFrequency : 5~20 Hz

Acceleration : 5.40 m/s rms

P.S.D. : 5~10 Hz +9 dB/Oct10~100 Hz 0.190 (m/s)/Hz

100~250 Hz -6 dB/OctTest Time : 1 hr

Test Axis : TransverseFrequency : 5~250 HzAcceleration : 4.71 m/s rms

P.S.D. : 5~10 Hz +9 dB/Oct

10~100 Hz 0.144 (m/s)/Hz


Acceleration : 5.40m/s rmsAcceleration : 5.40m/s rms

Test Axis : Longitudinal axisFrequency : 5~250 HzAcceleration : 2.52 m/s rms

P.S.D. : 5~10 Hz +9 dB/Oct10~100 Hz 0.0414 (m/s)/Hz


Total test Time : 3 hrs

B-3-7 Vibration Test Photograph of test setup


10/29

R/N:Page: 10 of 68

B-3-8 Vibration Test Curve


11/29

R/N:Page: 11 of 68

B-3-5 Vibration Test Result

B-4. Damp heat test cyclicB-4-1 Test Equipment

Programmable Temperature & Humidity ChamberK.SON. INS. TECH. CORP.Model: TS-F3L+-100

Date of Calibration: 04/01/05Serial Number: 1467


1. Test Temperature: 25 / 552. Test Humidity: 93~95%RH3. Test Cycle: 2 Cycle

B-4-3 Machine Curve


12/29

R/N:Page: 12 of 68

3 h 6 h

95%

93%

24 h (1 Cycle)

25

9 h

T1

Ambient temp.

10 min

relative humidity

45 to 75%

dielectric test

B-4-4 Test ResultPass: The system structure doesnt have any deformation; All functions are passed during humidity test.

C. EMC TestsC-1 EUT DESCRIPTIONProduct Embedded Control PC

Trade Name AAEON

Model AEC-6910

Housing Type Metal case

EUT Power Rating 100~240VAC

AC Power During Test 230VAC / 50Hz

Power Adaptor Manufacturer FSP

Power Adaptor Model Number FSP120-AAB

Power Adaptor Power Rating I/P: 100-240VAC 50-60Hz O/P: 19VDC

AC Power Cord Type Unshielded, 1.8m (Detachable)

DC Power Cord Type Unshielded, 1.6m (Non-detachable, with a core)EUT I/O Cable Unshielded, 0.3m (Detachable)

OSC/Clock Frequencies 32.768kHz; 14.31818MHz; 25MHz

C-2 I/O PORT OF EUT

I/O Port Type QTY TESTED WITH

PIO Port 1 1

SIO Port 4 4

PS/2 Keyboard Port 1 1

PS/2 Mouse Port 1 1

VIDEO-OUT Port (VGA) 1 1

AUDIO IN/OUT/ MIC Port 1 1

LAN Port 1 1USB Port 4 4

PCMCI Port 2 2

CF Slot 1 1

C-3 Conducted emission

C-3-1 Test Equipment

Conducted Emission Test Site # B


NUMBER

CAL.

DUE

TEST RECEIVER R&S ESHS10 843743/015 03/31/2006

LISN (EUT) EMCO 3825/2 9106-1810 01/16/2006LISN EMCO 3825/2 1382 01/16/2006

BNC CABLE MIYAZAKI 5D-FB BNC B1 07/14/2006

Pulse Limiter R&S ESH3-Z2 100374 08/25/2006

THERMO-HYGRO METER TOP HA-202 9303-3 03/02/2006


13/29


14/29

R/N:Page: 14 of 68


15/29

R/N:Page: 15 of 68

C-3-4 Performance and Result:Pass:No any emission over the limit line.

C-4. Radiated emission


Open Area Test Site J

EQUIPMENT MFR MODEL SERIAL no. CAL. DUE

SITE NSA CCS J Site N/A 10/15/2006

MEASURE RECEIVER SCHAFFNER SCR3501 330 06/13/2006


16/29

R/N:Page: 16 of 68

SPECTRUM ANALYZER ADVANTEST R3132 120900003 No Cal. Required

ANTENNA SCHAFFNER CBL 6112B 2800 09/24/2006

PRE-AMPLIFIER SCHAFFNER CPA9231A 3629 10/08/2006

CABLE BELDEN 9913 N-TYPE #J2 02/18/2006

ATTENUATOR MCL UNAT-6 AT06-8 12/03/2005

THERMO-HYGRO METER TFA N/A NO.3 11/02/2006

C-4-2 Test Photograph of test setup


17/29

R/N:Page: 17 of 68

C-4-2 Emission Profile


18/29


19/29

R/N:Page: 19 of 68

C-4-3 Performance and Result:Pass:No any emission over the limit line.


20/29

R/N:Page: 20 of 68

C-5. Fast transient burst immunityC-5-1 Test Equipment

Fast Transients/Burst Test Site (EN 61000-4-4)

Manufacturer/Type Model No. Serial No. Cal. Due

Schaffner / EFT Generator BEST EMC V2.3 200031A024SC 11/07/2006

Schaffner / Capacitive Clamp N/A N/A No Cal. Required

C-5-2 Test ConditionPort : AC Power Port and RJ45 PortBasic Standard : IEC/EN 61000-4-4

Requirements : 2 kV for AC Power Port 2 kV for RJ45 Port

Performance Criterion : The Equipment or System shall be able to provide the essential performance andremain safe.

Tested by : ALEX PANTemperature : 18

oC

Humidity : 56%Pressure : 1005mbar

C-5-3 Test Block Diagram of Test Setup

Controller Computer

EFT/Burst/Surge Generator

EUT SupportUnits

0.8mNon-Conductive Table

AC

Injection ClampBurst Generator

To Load

AC

Comm. Line 3 m

EUT

80cmNon-Conductive

Table

10cm



21/29

R/N:Page: 21 of 68

(IEC 61000-4-4 FOR I/O)

C-5-5 Performance and ResultImpulse Frequency : 5kHzTr/Th : 5/50nsBurst Duration : 15msBurst Period : 300ms


22/29

R/N:Page: 22 of 68

Inject Line Voltage kV Inject Method Result (Pass/Fail)

L 2 Direct Pass

N 2 Direct Pass

PE 2 Direct Pass

L + N 2 Direct PassL + PE 2 Direct Pass

N + PE 2 Direct Pass

L + N + PE 2 Direct Pass

RJ45 2 Clamp Pass

Pass:No function degraded during the tests.

The apparatus continues to operate as intended. No degradation of performance or loss of function is

allowed below a performance level specified by the manufacturer, when the apparatus is used as

intended. In some cases the performance level may be replaced by a permissible loss of performance.

C6 Surge immunityC-6-1 Test Equipment

Surge Immunity Test Site (EN 61000-4-5)


Schaffner / Surger Generator BEST EMC V2.3 200031A024SC 11/07/2006

Schaffner / Signal and Data

Lines Coupling NetworkCDN118 19328 No Cal. Required

C-6-2 Test ConditionPort : AC Power PortBasic Standard : IEC/EN 61000-4-5

Requirements : 2 kV(Line to Ground)) for AC Power Port

1.8kV(Line to Line) for AC Power PortPerformance Criteria : The Equipment or System shall be able to provide the

essential performance and remain safe.Tested by : ALEX PANTemperature : 20

oC



Surge Immunity

Test

Controller Computer

EUT

&

Support Units

0.8m

To AC

Source



23/29

R/N:Page: 23 of 68

C-6-5 Test Procedure1. The EUT and support units were located on a wooden table 0.8 m away from ground floor.

2. Injected test voltage to the EUT ports from minimum to standard request or client request.3. Recorded the test result as shown in following table.

C-6-6 Performance and ResultVoltage Waveform : 5/50 usCurrent Waveform : 8/20 usPolarity : Positive/NegativePhase angle : 0

o, 90

o, 270

o

Number of Test : 5

Coupling Line Voltage (kV) Polarity Coupling Method Result (Pass/Fail)

L1-L2 11.8 Positive Capacitive Pass

L1-PE 12 Positive Capacitive Pass

L2-PE 12 Positive Capacitive Pass

L1-L2 11.8 Negative Capacitive Pass

L1-PE 12 Negative Capacitive Pass

L2-PE 12 Negative Capacitive Pass

Pass : Where normal functioning of LAN cant be achieved because of the impact of CDN on the EUT, notest be required.

The apparatus continues to operate as intended. No degradation of performance or loss of function is

allowed below a performance level specified by the manufacturer, when the apparatus is used as

intended. In some cases the performance level may be replaced by a permissible loss of performance.


24/29

R/N:Page: 24 of 68

C-7 RFI immunity, Conducted


CS test (EN 61000-4-6)


Schaffner / RF Generator NSG 2070-1 1061 08/03/2006Schaffner / CDN CDN M316 19600 08/02/2006

Schaffner / CDN CDN M216 19294 08/02/2006

FCC / CDN FCC-801-M3-16A 99122 08/02/2006

Schaffner / EM Clamp KEMZ 801 19227 02/23/2006

Schaffner / CDN CDN T002 15881 01/13/2006

FCC / CDN FCC-801-T8-RJ45 04025 06/23/2006

Schaffner / Attenuator INA2070-1 2061 No Cal. Required

FCC / CDN FCC-801-T4-RJ45 04031 08/02/2006

C-7-2 Test Condition

Port : AC Power Port and RJ45 PortBasic Standard : IEC/EN 61000-4-6Requirements : 10V, with 80% AM. 1kHz Modulation.Injection Method : CDN-M3 for AC Power Port

CDN-T4 for RJ45 PortPerformance Criterion : A (Standard Required)Tested by : ALEX PANTemperature : 20

oC

Humidity : 56%Pressure : 1010mbarFrequency Range : 0.15MHz-80MHzFrequency Step : 1% of fundamentalDwell Time : 3 sec


CDN

EUT and

Support units Power

AmplifierPC

Controller

Ground Reference

10 cm isolation

supporter

0.1m< L


25/29

R/N:Page: 25 of 68

C-7-5 Test Procedure1. The EUT and support units were located at a ground reference plane with the interposition of a 0.1 m

thickness insulating support and the CDN was located on GRP directly.2. Set the testing parameters of CS test software as per IEC/EN 61000-4-6.

C-7-6 Performance and Result:


26/29

R/N:Page: 26 of 68

Range (MHz) Field Modulation Result (Pass/Fail)

0.15-80 10V Yes Pass

Pass:No function degraded during the tests.The apparatus continues to operate as intended. No degradation of performance or loss of function isallowed below a performance level specified by the manufacturer, when the apparatus is used asintended. In some cases the performance level may be replaced by a permissible loss of performance.

C-8 RFI immunity, radiatedC-8-1 Test Equipment

Radiated Electromagnetic Field Immunity Test Site (EN 61000-4-3)


Calibration of Field Chamber#RS RS3H-7 / RS3V-7 07/01/2006

Agilent / Signal Generator E4421B MY43350597 05/16/2006

AR / Electric Field Probe FP6001 305650 02/03/2006

Boonton / RF Voltmeter 9200B 328001AE 02/23/2006

BNC / Function Generator 625A 25451 02/17/2006

AR / Amplifier 100W1000M1 17564 No Cal. RequiredWerlatone Inc. / Direction Coupler C2630 4121 No Cal.Required

Frankonia /Broadband Antenna BTA-M 030001M No Cal. Required

TOP / Thermo-Hygro meter HA-202 9303-2 03/02/2006

C-8-2 Test Condiction

Port : EnclosureBasic Standard : IEC/EN 61000-4-3Requirements : 10V/m / with 80% AM. 1kHz Modulation.Performance Criterion : A (Standard Required)Tested by : ALEX PANTemperature : 18

oC



0.8m

Power Amp Signal

GeneratorEUT Monitoring by

using a camera

Control Room

7x3x3

EUT &

Support Units

PC Controller to

control S.G. & PA as

well as forward

power

3 meter

1.5 meter


27/29

R/N:Page: 27 of 68

C-8-4 Test Procedure1. The EUT and support units were located at the edge of supporting table keep 3 meter away from

transmitting antenna, it just the calibrated square area of field uniformity.2. Adjusting the cables to be exposed to the electromagnetic filed as possible.

3. Performing a Radiated Emission Scan in range of 80 to 1000 MHz prior to do RS test and records themore higher emission frequencies for the reference of RS test, due to antenna effectiveness.

4. Adjusting the monitoring camera to monitor the H message as clear as possible.5. Setting the testing parameters of RS test software per IEC 61000-4-3.6. Referring to the tested data of step 3 to performing the RS test from 30 to 2300 MHz.7. Recording the test result in following table.8. Changing the EUT to the other side and repeat step 3 to 6, until 4 sides of EUT were verified.


C-8-6 Performance and Result:

Test level : 10V/m

Steps : 1 % of fundamental

Dwell Time : 3 sec

Range (MHz) Field Modulation Polarity Position () Result (Pass/Fail)

80-1000 10V/m Yes H Front Pass

80-1000 10V/m Yes V Front Pass

80-1000 10V/m Yes H Right Pass

80-1000 10V/m Yes V Right Pass

80-1000 10V/m Yes H Back Pass

80-1000 10V/m Yes V Back Pass

80-1000 10V/m Yes H Left Pass

80-1000 10V/m Yes V Left Pass

Pass:No function degraded during the tests.The apparatus continues to operate as intended. No degradation of performance or loss of function isallowed below a performance level specified by the manufacturer, when the apparatus is used asintended. In some cases the performance level may be replaced by a permissible loss of performance.


28/29

R/N:Page: 28 of 68

C-9 Electrostatic dischargeC-9-1 Test Equipment

ESD Test Site (EN 61000-4-2)


Schaffner / ESD Simulator NSG 438 129 04/20/2006

Sato / Aneroid Barometer 7610-20 89090 08/29/2006TOP / Thermo-Hygro meter HA-202 9303-1 03/02/2006

C-9-2 Test Condition

Port : EnclosureBasic Standard : IEC/EN 61000-4-2Test Level : 8kV (Air Discharge)

6kV (Contact Discharge)Performance Criterion : The Equipment or System shall be able to provide the

essential performance and remain safe.Tested by : ELVIS ZENGTemperature : 19

oC

Humidity : 59% RH

Pressure : 1005mbar


Ground Reference Plane

Wooden Table

Indirect

Support units

EUT & its direct

Support Units

VCP

HCP

>1m

0.8m

(The 470 k resistors are installed per standard requirement.)



29/29

R/N:Page: 29 of 68

C-9-5Test Performance and ResultThe electrostatic discharges were applied as follows:

Amount of Discharges Voltage Coupling Result20 / Point 8kV Air Discharge Pass

20 / Point 6 kV Contact Discharge Pass

20 / Point 2, 4, 6 kV Indirect Discharge HCP Pass

20 / Point 2, 4, 6 kV Indirect Discharge VCP (Front) Pass

20 / Point 2, 4, 6 kV Indirect Discharge VCP (Left) Pass

20 / Point 2, 4, 6 kV Indirect Discharge VCP (Back) Pass

20 / Point 2, 4, 6 kV Indirect Discharge VCP (Right) Pass

Observation: No function degraded during the tests.

AEC-6910 en-50155 Test Report

Documents

Transcript of AEC-6910 en-50155 Test Report