Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation...
Transcript of Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation...
![Page 1: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/1.jpg)
w w w . s c h u n k . c o m162
technical data
Loads and load torques
Designation B 40-ZSSMax. travel speed [m/s] 3Repeat accuracy [mm] ± 0.08Max. acceleration [m/s²] 30Idle torque [Nm] 0.3DriveDrive element Toothed belt 16 AT 5-ETravel per revolution [mm] 100Maximum stroke [mm] 850Max. total length [mm] 1070Moment of inertia [kgm²] 0.0002WeightsBasic without travel [kg] 1.7Travel per 100 mm [kg] 0.3Slide plate 120 mm [kg] 0.3Slide plate 200 mm [kg] 0.5
Advantages of profiled rail guide
Linear Axes · toothed-belt Drive
B 40-ZSS
High load bearing capacity
Long lifetime
High precision
Load Dynamic Fx** [N] 500 Fy
[N] 500 Fz
[N] 600 -Fz
[N] 300Load torques Dynamic
Mx[Nm] 12
My[Nm] 30 (50)
Mz[Nm] 30 (50)
MAmax[Nm] 8.3
** Maximum value = Depending on speed Values in brackets relate to the long slide.
www.comoso.com
![Page 2: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/2.jpg)
w w w . s c h u n k . c o m 163
main views
Assembly connection Drive connection8 Feather key DIN 68859 Useful stroke
L Bolt pitch circle
Linear Axes · toothed-belt Drive
B 40-ZSS
Long slide
9 Useful stroke 8 Feather keyCaution: No plug-in drive shaft – AZ – Define position
(see order designation)!
Drive journal connection dimensions
www.comoso.com
![Page 3: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/3.jpg)
w w w . s c h u n k . c o m164
Linear Axes · toothed-belt Drive
B 40-ZSS
mountingProfile ZSS
The profile can be secured either using T-nuts or mounting strips.
Designation Order designation ID no.T-nut NS7 0331423Mounting strip BL1 0331400
motor flange schematic diagram
The table shows the relevant dimension C of the standard couplings. For dimension A refer to drive journal connection dimensions, for dimension B refer to corresponding motor dimension sheet, dimension L may differ in individual cases.Different drive solutions can be attached to our axes.SCHUNK can supply you with the right motor flange and coupling for your drive.
Because of the different thermal behavior of motors, we recommend that the drive solution is tested by the motor manufacturer.
L = A + B + C
Specific mass [kg/m] 1.71Planar dimension [mm²] 635Planar moment of inertia ly [mm4] 88917Planar moment of inertia lz [mm4] 133350Load torque Wy [mm³] 3757Load torque Wz [mm³] 6665
More detailed information on pedestal bearings, connection shafts and bevel gears can be found in the "OPTIONS for System HSB" section of the catalog.
A Mounting strip K Side T-nut
www.comoso.com
![Page 4: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/4.jpg)
w w w . s c h u n k . c o m 165
Linear Axes · toothed-belt Drive
B 40-ZSS
Lubrication connections
Limit switch selectionLimit switch position
T Standard lubrication connection
Standard connectionLubrication nipple M8x1
If the lubrication connection has a different seat, this must be defined in the order text.
Drive shafts
Depending on the axis application, the drive shaft seat may need to be defined in the order text. Particularly with axis combinations and mechanical synchronization, multiple drive shafts - some of them continuous shafts - are required.
T Limit switch standard position
Two EO2 switches are used as limit switches and an RS2 as the reference switch as standard.
The positions and dimensions of limit switches, switching lugs, and mounting components may vary depending on the application and the selected limit switches. Please contact us for assistance.
More detailed information on pedestal bearings, connection shafts and bevel gears can be found in the "OPTIONS for System HSB" section of the catalog.
Designation Order designation ID no.Inductive limit switch, opener, 2 m cable EO2 0331410Inductive limit switch, opener, 10 m cable EO10 0331412Inductive limit switch, closer, 2 m cable ES2 0331411Inductive limit switch, closer, 10 m cable ES10 0331413Mechanical limit switch (Siemens), opener EMS 0331414Mechanical limit switch (Balluff), opener EMB 0331415
www.comoso.com
![Page 5: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/5.jpg)
w w w . s c h u n k . c o m166
technical data
Loads and load torques
Designation B 50C-ZRSMax. travel speed [m/s] 3Repeat accuracy [mm] ± 0.08Max. acceleration [m/s²] 30Idle torque [Nm] 0.4DriveDrive element Toothed belt 20 AT 5-ETravel per revolution [mm] 110Maximum stroke [mm] 7710Max. total length [mm] 8000Moment of inertia [kgm²] 0.0003WeightsBasic without travel [kg] 1.45Travel per 100 mm [kg] 0.35Slide plate 150 mm [kg] 0.45Slide plate 200 mm [kg] 0.6
Linear Axes · toothed-belt Drive
B 50C-ZRS
Load Dynamic Fx** [N] 700 Fy
[N] 300 Fz
[N] 600 -Fz
[N] 400Load torques Dynamic
Mx[Nm] 30
My[Nm] 50 (65)
Mz[Nm] 50 (65)
MAmax[Nm] 12.7
** Maximum value = Depending on speed Values in brackets relate to the long slide.
High maximum moments due to optimum force transmission to the profile
Long stroke lengths can be achieved with no problems
Life-time lubricated rollers for easy maintenance use
Smooth, low-noise running
Advantages of roller guide
www.comoso.com
![Page 6: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/6.jpg)
w w w . s c h u n k . c o m 167
main views
Assembly connection Drive connection8 Feather key DIN 68859 Useful stroke
Mounting groove for T-nutsL Bolt pitch circle
Linear Axes · toothed-belt Drive
B 50C-ZRS
Long slide
9 Useful stroke 8 Feather key
Drive journal connection dimensions
www.comoso.com
![Page 7: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/7.jpg)
w w w . s c h u n k . c o m168
Linear Axes · toothed-belt Drive
mountingProfile ZRS
The profile can be secured either using T-nuts or mounting strips.
Designation Order designation ID no.T-nut NS2 0331405T-nut RM2 0331425Mounting strip BL1 0331400
motor flange schematic diagram
The table shows the relevant dimension C of the standard couplings. For dimension A refer to drive journal connection dimensions, for dimension B refer to corresponding motor dimension sheet, dimension L may differ in individual cases.Different drive solutions can be attached to our axes.SCHUNK can supply you with the right motor flange and coupling for your drive.
Because of the different thermal behavior of motors, we recommend that the drive solution is tested by the motor manufacturer.
L = A + B + C
Specific mass [kg/m] 2.45Planar dimension [mm²] 908Planar moment of inertia ly [mm4] 236683Planar moment of inertia lz [mm4] 295187Load torque Wy [mm³] 8622Load torque Wz [mm³] 11804
More detailed information on pedestal bearings, connection shafts and bevel gears can be found in the "OPTIONS for System HSB" section of the catalog.
B 50C-ZRS
A Mounting strip T T-nut on base side
www.comoso.com
![Page 8: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/8.jpg)
w w w . s c h u n k . c o m 169
Linear Axes · toothed-belt Drive
Lubrication connections
Limit switch selectionLimit switch position
T Standard lubrication connection
Standard connectionLubrication nipple M8x1
If the lubrication connection has a different seat, this must be defined in the order text.
Drive shafts
Depending on the axis application, the drive shaft seat may need to be defined in the order text. Particularly with axis combinations and mechanical synchronization, multiple drive shafts - some of them continuous shafts - are required.
T Limit switch standard position
Two EO2 switches are used as limit switches and an RS2 as the reference switch as standard.
The positions and dimensions of limit switches, switching lugs, and mounting components may vary depending on the application and the selected limit switches. Please contact us for assistance.
More detailed information on pedestal bearings, connection shafts and bevel gears can be found in the "OPTIONS for System HSB" section of the catalog.
Designation Order designation ID no.Inductive limit switch, opener, 2 m cable EO2 0331410Inductive limit switch, opener, 10 m cable EO10 0331412Inductive limit switch, closer, 2 m cable ES2 0331411Inductive limit switch, closer, 10 m cable ES10 0331413Mechanical limit switch (Siemens), opener EMS 0331414Mechanical limit switch (Balluff), opener EMB 0331415
B 50C-ZRSwww.comoso.com
![Page 9: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/9.jpg)
w w w . s c h u n k . c o m170
technical data
Loads and load torques
Designation B 50C-ARSMax. travel speed [m/s] 3Repeat accuracy [mm] ± 0.08Max. acceleration [m/s²] 30Idle torque [Nm] 1.5DriveDrive element Toothed belt 20 AT 5-ETravel per revolution [mm] 110Maximum stroke [mm] 7710Max. total length [mm] 8000Moment of inertia [kgm²] 0.0003WeightsBasic without travel [kg] 2.5Travel per 100 mm [kg] 0.3Slide drive 140 mm [kg] 1.25
Linear Axes · toothed-belt Drive
B 50C-ARS
Load Dynamic Fx** [N] 700 Fy
[N] 300 Fz
[N] 600 -Fz
[N] 400Load torques Dynamic
Mx[Nm] 30
My[Nm] 50
Mz[Nm] 50
MAmax[Nm] 13.8
** Maximum value = Depending on speed Values in brackets relate to the long slide.
High maximum moments due to optimum force transmission to the profile
Long stroke lengths can be achieved with no problems
Life-time lubricated rollers for easy maintenance use
Smooth, low-noise running
Advantages of roller guide
www.comoso.com
![Page 10: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/10.jpg)
w w w . s c h u n k . c o m 171
main views
Linear unit connection Assembly connection Drive connection8 Feather key DIN 68859 Useful stroke
Mounting groove for T-nutsL Bolt pitch circle
Linear Axes · toothed-belt Drive
B 50C-ARS
8 Feather key
Drive journal connection dimensions
www.comoso.com
![Page 11: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/11.jpg)
w w w . s c h u n k . c o m172
Linear Axes · toothed-belt Drive
mountingProfile ARS
The profile can be secured either using T-nuts or mounting strips.
Designation Order designation ID no.T-nut NS2 0331405T-nut RM2 0331425Mounting strip BL1 0331400
motor flange schematic diagram
The table shows the relevant dimension C of the standard couplings. For dimension A refer to drive journal connection dimensions, for dimension B refer to corresponding motor dimension sheet, dimension L may differ in individual cases.Different drive solutions can be attached to our axes.SCHUNK can supply you with the right motor flange and coupling for your drive.
Because of the different thermal behavior of motors, we recommend that the drive solution is tested by the motor manufacturer.
L = A + B + C
Specific mass [kg/m] 2.45Planar dimension [mm²] 908Planar moment of inertia ly [mm4] 236683Planar moment of inertia lz [mm4] 295187Load torque Wy [mm³] 8622Load torque Wz [mm³] 11804
More detailed information on pedestal bearings, connection shafts and bevel gears can be found in the "OPTIONS for System HSB" section of the catalog.
B 50C-ARS
A Mounting strip T T-nut on base side
www.comoso.com
![Page 12: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/12.jpg)
w w w . s c h u n k . c o m 173
Linear Axes · toothed-belt Drive
Lubrication connections
Limit switch selectionLimit switch position
T Standard lubrication connection
Standard connectionLubrication nipple M8x1
If the lubrication connection has a different seat, this must be defined in the order text.
Drive shafts
Depending on the axis application, the drive shaft seat may need to be defined in the order text. Particularly with axis combinations and mechanical synchronization, multiple drive shafts - some of them continuous shafts - are required.
T Limit switch standard position
Two EO2 switches are used as limit switches and an RS2 as the reference switch as standard.
The positions and dimensions of limit switches, switching lugs, and mounting components may vary depending on the application and the selected limit switches. Please contact us for assistance.
More detailed information on pedestal bearings, connection shafts and bevel gears can be found in the "OPTIONS for System HSB" section of the catalog.
Designation Order designation ID no.Inductive limit switch, opener, 2 m cable EO2 0331410Inductive limit switch, opener, 10 m cable EO10 0331412Inductive limit switch, closer, 2 m cable ES2 0331411Inductive limit switch, closer, 10 m cable ES10 0331413Mechanical limit switch (Siemens), opener EMS 0331414Mechanical limit switch (Balluff), opener EMB 0331415
B 50C-ARSwww.comoso.com
![Page 13: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/13.jpg)
w w w . s c h u n k . c o m174
technical data
Loads and load torques
Designation B 60-ZSSMax. travel speed [m/s] 5Repeat accuracy [mm] ± 0.08Max. acceleration [m/s²] 30Idle torque [Nm] 1.1DriveDrive element Toothed belt 25 AT 5-ETravel per revolution [mm] 160Maximum stroke [mm] 7620Max. total length [mm] 8000Moment of inertia [kgm²] 0.0002WeightsBasic without travel [kg] 4.55Travel per 100 mm [kg] 0.59Slide plate 190 mm [kg] 1.22Slide plate 230 mm [kg] 1.72
Advantages of profiled rail guide
Linear Axes · toothed-belt Drive
B 60-ZSS
High load bearing capacity
Long lifetime
High precision
Load Dynamic Fx** [N] 850 Fy
[N] 500 Fz
[N] 1400 -Fz
[N] 800Load torques Dynamic
Mx[Nm] 50
My[Nm] 160 (200)
Mz[Nm] 160 (200)
MAmax[Nm] 22.7
** Maximum value = Depending on speed Values in brackets relate to the long slide.
www.comoso.com
![Page 14: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/14.jpg)
w w w . s c h u n k . c o m 175
main views
Assembly connection Drive connection8 Feather key DIN 68859 Useful stroke
Mounting groove for T-nuts
Linear Axes · toothed-belt Drive
B 60-ZSS
Long slide
9 Useful stroke 8 Feather key
Drive journal connection dimensions
www.comoso.com
![Page 15: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/15.jpg)
w w w . s c h u n k . c o m176
Linear Axes · toothed-belt Drive
B 60-ZSS
mountingProfile ZSS
The profile can be secured either using T-nuts or mounting strips.
Designation Order designation ID no.T-nut NS8 0331420T-nut NS9 0331421T-nut NS12 0331424Mounting strip BL5 0331419
motor flange schematic diagram
The table shows the relevant dimension C of the standard couplings. For dimension A refer to drive journal connection dimensions, for dimension B refer to corresponding motor dimension sheet, dimension L may differ in individual cases.Different drive solutions can be attached to our axes.SCHUNK can supply you with the right motor flange and coupling for your drive.
Because of the different thermal behavior of motors, we recommend that the drive solution is tested by the motor manufacturer.
L = A + B + C
Specific mass [kg/m] 3.02Planar dimension [mm²] 1117Planar moment of inertia ly [mm4] 400283Planar moment of inertia lz [mm4] 521983Load torque Wy [mm³] 11929Load torque Wz [mm³] 17380
More detailed information on pedestal bearings, connection shafts and bevel gears can be found in the "OPTIONS for System HSB" section of the catalog.
A Mounting strip T T-nut on base side K Side T-nut
www.comoso.com
![Page 16: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/16.jpg)
w w w . s c h u n k . c o m 177
Linear Axes · toothed-belt Drive
B 60-ZSS
Lubrication connections
Limit switch selectionLimit switch position
T Standard lubrication connection
Standard connectionLubrication nipple M8x1
If the lubrication connection has a different seat, this must be defined in the order text.
Drive shafts
Depending on the axis application, the drive shaft seat may need to be defined in the order text. Particularly with axis combinations and mechanical synchronization, multiple drive shafts - some of them continuous shafts - are required.
T Limit switch standard position
Two EO2 switches are used as limit switches and an RS2 as the reference switch as standard.
The positions and dimensions of limit switches, switching lugs, and mounting components may vary depending on the application and the selected limit switches. Please contact us for assistance.
More detailed information on pedestal bearings, connection shafts and bevel gears can be found in the "OPTIONS for System HSB" section of the catalog.
Designation Order designation ID no.Inductive limit switch, opener, 2 m cable EO2 0331410Inductive limit switch, opener, 10 m cable EO10 0331412Inductive limit switch, closer, 2 m cable ES2 0331411Inductive limit switch, closer, 10 m cable ES10 0331413Mechanical limit switch (Siemens), opener EMS 0331414Mechanical limit switch (Balluff), opener EMB 0331415
www.comoso.com
![Page 17: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/17.jpg)
w w w . s c h u n k . c o m178
technical data
Loads and load torques
Designation B 70C-ZRS B 70C-ZSSMax. travel speed [m/s] 8 5Repeat accuracy [mm] ± 0.08 ± 0.08Max. acceleration [m/s²] 30 30Idle torque [Nm] 1.2 1.2DriveDrive element Toothed belt 32 AT 5-E 32 AT 5-ETravel per revolution [mm] 175 175Maximum stroke [mm] 7640 6840Max. total length [mm] 8000 7200Moment of inertia [kgm²] 0.0004 0.0002WeightsBasic without travel [kg] 3.1 3.4Travel per 100 mm [kg] 0.59 0.38Slide plate 190 mm [kg] 1.3 1.65Slide plate 240 mm [kg] 1.65 2.1
Advantages of profiled rail guide
Linear Axes · toothed-belt Drive
B 70C-ZRS/-ZSS
High load bearing capacity
Long lifetime
High precision
Load ZRS dynamic ZSS dynamic Fx** [N] 1100 1100 Fy
[N] 300 600 Fz
[N] 1000 1800 -Fz
[N] 400 1200Load torques ZRS dynamic ZSS dynamic
Mx[Nm] 35 60
My[Nm] 120 (150) 180 (230)
Mz[Nm] 50 (60) 120 (150)
MAmax[Nm] 31.8 31.8
** Maximum value = Depending on speed Values in brackets relate to the long slide.
High maximum moments due to optimum force transmission to the profile
Long stroke lengths can be achieved with no problems
Life-time lubricated rollers for easy maintenance use
Smooth, low-noise running
Advantages of roller guide
www.comoso.com
![Page 18: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/18.jpg)
w w w . s c h u n k . c o m 179
main views
Assembly connection Drive connection8 Feather key DIN 68859 Useful stroke
Mounting groove for T-nutsL Bolt pitch circle
Linear Axes · toothed-belt Drive
B 70C-ZRS/-ZSS
Long slide
9 Useful stroke 8 Feather key
Drive journal connection dimensions
www.comoso.com
![Page 19: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/19.jpg)
w w w . s c h u n k . c o m180
Linear Axes · toothed-belt Drive
B 70C-ZRS/-ZSS
mounting
Profile ZRS
The profile can be secured either using T-nuts or mounting strips.
Designation Order designation ID no.T-nut NS2 0331405T-nut RM2 0331425Mounting strip BL1 0331400
motor flange schematic diagram
The table shows the relevant dimension C of the standard couplings. For dimension A refer to drive journal connection dimensions, for dimension B refer to corresponding motor dimension sheet, dimension L may differ in individual cases.Different drive solutions can be attached to our axes.SCHUNK can supply you with the right motor flange and coupling for your drive.
Because of the different thermal behavior of motors, we recommend that the drive solution is tested by the motor manufacturer.
L = A + B + C
Specific mass [kg/m] 3.7Planar dimension [mm²] 1370Planar moment of inertia ly [mm4] 585283Planar moment of inertia lz [mm4] 854713Load torque Wy [mm³] 15835Load torque Wz [mm³] 24410
Profile ZSS
Specific mass [kg/m] 3.7Planar dimension [mm²] 1370Planar moment of inertia ly [mm4] 563059Planar moment of inertia lz [mm4] 852507Load torque Wy [mm³] 14743Load torque Wz [mm³] 24335
More detailed information on pedestal bearings, connection shafts and bevel gears can be found in the "OPTIONS for System HSB" section of the catalog.
A Mounting strip T T-nut on base side
www.comoso.com
![Page 20: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/20.jpg)
w w w . s c h u n k . c o m 181
Linear Axes · toothed-belt Drive
B 70C-ZRS/-ZSS
Lubrication connections
Limit switch selectionLimit switch position
T Standard lubrication connection
Standard connectionLubrication nipple M8x1
If the lubrication connection has a different seat, this must be defined in the order text.
Drive shafts
Depending on the axis application, the drive shaft seat may need to be defined in the order text. Particularly with axis combinations and mechanical synchronization, multiple drive shafts - some of them continuous shafts - are required.
T Limit switch standard position
Two EO2 switches are used as limit switches and an RS2 as the reference switch as standard.
The positions and dimensions of limit switches, switching lugs, and mounting components may vary depending on the application and the selected limit switches. Please contact us for assistance.
More detailed information on pedestal bearings, connection shafts and bevel gears can be found in the "OPTIONS for System HSB" section of the catalog.
Designation Order designation ID no.Inductive limit switch, opener, 2 m cable EO2 0331410Inductive limit switch, opener, 10 m cable EO10 0331412Inductive limit switch, closer, 2 m cable ES2 0331411Inductive limit switch, closer, 10 m cable ES10 0331413Mechanical limit switch (Siemens), opener EMS 0331414Mechanical limit switch (Balluff), opener EMB 0331415
www.comoso.com
![Page 21: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/21.jpg)
w w w . s c h u n k . c o m182
technical data
Loads and load torques
Designation B 70C-ARS B 70C-ASSMax. travel speed [m/s] 5 5Repeat accuracy [mm] ± 0.08 ± 0.08Max. acceleration [m/s²] 30 30Idle torque [Nm] 1 1DriveDrive element Toothed belt 32 AT 5-E 32 AT 5-ETravel per revolution [mm] 220 220Maximum stroke [mm] 7640 7640Max. total length [mm] 8000 8000Moment of inertia [kgm²] 0.0061 0.0061WeightsBasic without travel [kg] 7.5 7.9Travel per 100 mm [kg] 0.38 0.60Slide drive 220 mm [kg] 5.0 5.5
Advantages of profiled rail guide
Linear Axes · toothed-belt Drive
B 70C-ARS/-ASS
High load bearing capacity
Long lifetime
High precision
Load ARS dynamic ASS dynamic Fx** [N] 900 900 Fy
[N] 300 600 Fz
[N] 1000 1800 -Fz
[N] 400 1200Load torques ARS dynamic ASS dynamic
Mx[Nm] 35 60
My[Nm] 120 180
Mz[Nm] 50 120
MAmax[Nm] 32.5 32.5
** Maximum value = Depending on speed Values in brackets relate to the long slide.
High maximum moments due to optimum force transmission to the profile
Long stroke lengths can be achieved with no problems
Life-time lubricated rollers for easy maintenance use
Smooth, low-noise running
Advantages of roller guide
www.comoso.com
![Page 22: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/22.jpg)
w w w . s c h u n k . c o m 183
main views
Linear unit connection Assembly connection Drive connection8 Feather key DIN 68859 Useful stroke
Mounting groove for T-nutsL Bolt pitch circle
Linear Axes · toothed-belt Drive
B 70C-ARS/-ASS
8 Feather key
Drive journal connection dimensions
www.comoso.com
![Page 23: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/23.jpg)
w w w . s c h u n k . c o m184
Linear Axes · toothed-belt Drive
B 70C-ARS/-ASS
mounting
Profile ARS
The profile can be secured either using T-nuts or mounting strips.
Designation Order designation ID no.T-nut NS2 0331405T-nut RM2 0331425Mounting strip BL1 0331400
motor flange schematic diagram
The table shows the relevant dimension C of the standard couplings. For dimension A refer to drive journal connection dimensions, for dimension B refer to corresponding motor dimension sheet, dimension L may differ in individual cases.Different drive solutions can be attached to our axes.SCHUNK can supply you with the right motor flange and coupling for your drive.
Because of the different thermal behavior of motors, we recommend that the drive solution is tested by the motor manufacturer.
L = A + B + C
Specific mass [kg/m] 3.7Planar dimension [mm²] 1370Planar moment of inertia ly [mm4] 585283Planar moment of inertia lz [mm4] 854713Load torque Wy [mm³] 15835Load torque Wz [mm³] 24410
Profile ASS
Specific mass [kg/m] 3.7Planar dimension [mm²] 1370Planar moment of inertia ly [mm4] 563059Planar moment of inertia lz [mm4] 852507Load torque Wy [mm³] 14743Load torque Wz [mm³] 24335
More detailed information on pedestal bearings, connection shafts and bevel gears can be found in the "OPTIONS for System HSB" section of the catalog.
A Mounting strip T T-nut on base side
www.comoso.com
![Page 24: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/24.jpg)
w w w . s c h u n k . c o m 185
Linear Axes · toothed-belt Drive
B 70C-ZRS/-ZSS
Lubrication connections
Limit switch selectionLimit switch position
T Standard lubrication connection
Standard connectionLubrication nipple M8x1
If the lubrication connection has a different seat, this must be defined in the order text.
Drive shafts
Depending on the axis application, the drive shaft seat may need to be defined in the order text. Particularly with axis combinations and mechanical synchronization, multiple drive shafts - some of them continuous shafts - are required.
T Limit switch standard position
Two EO2 switches are used as limit switches and an RS2 as the reference switch as standard.
The positions and dimensions of limit switches, switching lugs, and mounting components may vary depending on the application and the selected limit switches. Please contact us for assistance.
More detailed information on pedestal bearings, connection shafts and bevel gears can be found in the "OPTIONS for System HSB" section of the catalog.
Designation Order designation ID no.Inductive limit switch, opener, 2 m cable EO2 0331410Inductive limit switch, opener, 10 m cable EO10 0331412Inductive limit switch, closer, 2 m cable ES2 0331411Inductive limit switch, closer, 10 m cable ES10 0331413Mechanical limit switch (Siemens), opener EMS 0331414Mechanical limit switch (Balluff), opener EMB 0331415
www.comoso.com
![Page 25: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/25.jpg)
w w w . s c h u n k . c o m186
technical data
Loads and load torques
Designation B 80-ZRS B 80-ZSSMax. travel speed [m/s] 8 5Repeat accuracy [mm] 0.08 0.08Max. acceleration [m/s²] 40 40Idle torque [Nm] 1.5 1.5DriveDrive element Toothed belt 32 AT 5-E 32 AT 5-ETravel per revolution [mm] 220 220Maximum stroke [mm] 7600 7600Max. total length [mm] 8000 8000Moment of inertia [kgm²] 0.0033 0.003WeightsBasic without travel [kg] 5.5 6.1Travel per 100 mm [kg] 0.6 0.85Slide plate 210 mm [kg] 2.1 1.8Slide plate 270 mm [kg] 2.7 2.3
Advantages of profiled rail guide
Linear Axes · toothed-belt Drive
B 80-ZRS/-ZSS
High load bearing capacity
Long lifetime
High precision
Load ZRS dynamic ZSS dynamic Fx** [N] 1350 1350 Fy
[N] 500 800 Fz
[N] 1500 3000 -Fz
[N] 800 2000Load torques ZRS dynamic ZSS dynamic
Mx[Nm] 50 100
My[Nm] 180 (220) 250 (300)
Mz[Nm] 100 (130) 250 (300)
MAmax[Nm] 48.8 48.8
** Maximum value = Depending on speed Values in brackets relate to the long slide.
High maximum moments due to optimum force transmission to the profile
Long stroke lengths can be achieved with no problems
Life-time lubricated rollers for easy maintenance use
Smooth, low-noise running
Advantages of roller guide
www.comoso.com
![Page 26: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/26.jpg)
w w w . s c h u n k . c o m 187
main views
Assembly connection Drive connection8 Feather key DIN 68859 Useful stroke
Mounting groove for T-nutsL Bolt pitch circleT Change of dimension with optional cover tape
Linear Axes · toothed-belt Drive
B 80-ZRS/-ZSS
8 Feather key
Drive journal connection dimensionsLong slide
9 Useful stroke
www.comoso.com
![Page 27: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/27.jpg)
w w w . s c h u n k . c o m188
Linear Axes · toothed-belt Drive
B 80-ZRS/-ZSS
mounting
Profile ZRS
The profile can be secured either using T-nuts or mounting strips.
Designation Order designation ID no.T-nut NS3 0331406T-nut RM4 0331426Mounting strip BL2 0331401
motor flange schematic diagram
The table shows the relevant dimension C of the standard couplings. For dimension A refer to drive journal connection dimensions, for dimension B refer to corresponding motor dimension sheet, dimension L may differ in individual cases.Different drive solutions can be attached to our axes.SCHUNK can supply you with the right motor flange and coupling for your drive.
Because of the different thermal behavior of motors, we recommend that the drive solution is tested by the motor manufacturer.
L = A + B + C
Specific mass [kg/m] 5.64Planar dimension [mm²] 2090Planar moment of inertia ly [mm4] 1294343Planar moment of inertia lz [mm4] 1732340Load torque Wy [mm³] 30263Load torque Wz [mm³] 43258
Profile ZSS
Specific mass [kg/m] 5.4Planar dimension [mm²] 2000Planar moment of inertia ly [mm4] 1303940Planar moment of inertia lz [mm4] 1680598Load torque Wy [mm³] 29397Load torque Wz [mm³] 41895
More detailed information on pedestal bearings, connection shafts and bevel gears can be found in the "OPTIONS for System HSB" section of the catalog.
A Mounting strip T T-nut on base side
www.comoso.com
![Page 28: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/28.jpg)
w w w . s c h u n k . c o m 189
Linear Axes · toothed-belt Drive
B 80-ZRS/-ZSS
Lubrication connections
Limit switch selectionLimit switch position
T Standard lubrication connection
Standard connectionLubrication nipple M8x1
If the lubrication connection has a different seat, this must be defined in the order text.
Drive shafts
Depending on the axis application, the drive shaft seat may need to be defined in the order text. Particularly with axis combinations and mechanical synchronization, multiple drive shafts - some of them continuous shafts - are required.
T Limit switch standard position
Two EO2 switches are used as limit switches and an RS2 as the reference switch as standard.
The positions and dimensions of limit switches, switching lugs, and mounting components may vary depending on the application and the selected limit switches. Please contact us for assistance.
More detailed information on pedestal bearings, connection shafts and bevel gears can be found in the "OPTIONS for System HSB" section of the catalog.
Designation Order designation ID no.Inductive limit switch, opener, 2 m cable EO2 0331410Inductive limit switch, opener, 10 m cable EO10 0331412Inductive limit switch, closer, 2 m cable ES2 0331411Inductive limit switch, closer, 10 m cable ES10 0331413Mechanical limit switch (Siemens), opener EMS 0331414Mechanical limit switch (Balluff), opener EMB 0331415
www.comoso.com
![Page 29: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/29.jpg)
w w w . s c h u n k . c o m190
technical data
Loads and load torques
Designation B 80-ARS B 80-ASSMax. travel speed [m/s] 8 5Repeat accuracy [mm] ± 0.08 ± 0.08Max. acceleration [m/s²] 40 40Idle torque [Nm] 1.5 1.5DriveDrive element Toothed belt 32 AT 10 32 AT 10Travel per revolution [mm] 220 220Maximum stroke [mm] 7590 7590Max. total length [mm] 8000 8000Moment of inertia [kgm²] 0.0092 0.0086WeightsBasic without travel [kg] 10.5 11.5Travel per 100 mm [kg] 0.6 0.85Slide drive 260 mm [kg] 7.5 7.0
Advantages of profiled rail guide
Linear Axes · toothed-belt Drive
B 80-ARS/-ASS
High load bearing capacity
Long lifetime
High precision
Load ARS dynamic ASS dynamic Fx** [N] 1000 1000 Fy
[N] 500 800 Fz
[N] 1500 3000 -Fz
[N] 800 2000Load torques ARS dynamic ASS dynamic
Mx[Nm] 50 100
My[Nm] 180 250
Mz[Nm] 100 250
MAmax[Nm] 36.5 36.5
** Maximum value = Depending on speed Values in brackets relate to the long slide.
High maximum moments due to optimum force transmission to the profile
Long stroke lengths can be achieved with no problems
Life-time lubricated rollers for easy maintenance use
Smooth, low-noise running
Advantages of roller guide
www.comoso.com
![Page 30: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/30.jpg)
w w w . s c h u n k . c o m 191
main views
Linear unit connection Assembly connection Drive connection8 Feather key DIN 68859 Useful stroke
Mounting groove for T-nutsL Bolt pitch circle
Linear Axes · toothed-belt Drive
B 80-ARS/-ASS
8 Feather key
Drive journal connection dimensions
www.comoso.com
![Page 31: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/31.jpg)
w w w . s c h u n k . c o m192
Linear Axes · toothed-belt Drive
B 80-ARS/-ASS
mounting
Profile ARS
The profile can be secured either using T-nuts or mounting strips.
Designation Order designation ID no.T-nut NS3 0331406T-nut RM4 0331426Mounting strip BL2 0331401
motor flange schematic diagram
The table shows the relevant dimension C of the standard couplings. For dimension A refer to drive journal connection dimensions, for dimension B refer to corresponding motor dimension sheet, dimension L may differ in individual cases.Different drive solutions can be attached to our axes.SCHUNK can supply you with the right motor flange and coupling for your drive.
Because of the different thermal behavior of motors, we recommend that the drive solution is tested by the motor manufacturer.
L = A + B + C
Specific mass [kg/m] 5.64Planar dimension [mm²] 2090Planar moment of inertia ly [mm4] 1294343Planar moment of inertia lz [mm4] 1732340Load torque Wy [mm³] 30263Load torque Wz [mm³] 43258
Profile ASS
Specific mass [kg/m] 5.4Planar dimension [mm²] 2000Planar moment of inertia ly [mm4] 1303940Planar moment of inertia lz [mm4] 1680598Load torque Wy [mm³] 29397Load torque Wz [mm³] 41895
More detailed information on pedestal bearings, connection shafts and bevel gears can be found in the "OPTIONS for System HSB" section of the catalog.
A Mounting strip T T-nut on base side
www.comoso.com
![Page 32: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/32.jpg)
w w w . s c h u n k . c o m 193
Linear Axes · toothed-belt Drive
B 80-ARS/-ASS
Lubrication connections
Limit switch selectionLimit switch position
T Standard lubrication connection
Standard connectionLubrication nipple M8x1
If the lubrication connection has a different seat, this must be defined in the order text.
Drive shafts
Depending on the axis application, the drive shaft seat may need to be defined in the order text. Particularly with axis combinations and mechanical synchronization, multiple drive shafts - some of them continuous shafts - are required.
T Limit switch standard position
Two EO2 switches are used as limit switches and an RS2 as the reference switch as standard.
The positions and dimensions of limit switches, switching lugs, and mounting components may vary depending on the application and the selected limit switches. Please contact us for assistance.
More detailed information on pedestal bearings, connection shafts and bevel gears can be found in the "OPTIONS for System HSB" section of the catalog.
Designation Order designation ID no.Inductive limit switch, opener, 2 m cable EO2 0331410Inductive limit switch, opener, 10 m cable EO10 0331412Inductive limit switch, closer, 2 m cable ES2 0331411Inductive limit switch, closer, 10 m cable ES10 0331413Mechanical limit switch (Siemens), opener EMS 0331414Mechanical limit switch (Balluff), opener EMB 0331415
www.comoso.com
![Page 33: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/33.jpg)
w w w . s c h u n k . c o m194
technical data
Loads and load torques
Designation B 80C-ZSSMax. travel speed [m/s] 5Repeat accuracy [mm] ± 0.08Max. acceleration [m/s²] 40Idle torque [Nm] 1.8DriveDrive element Toothed belt 32 AT 10Travel per revolution [mm] 210Maximum stroke [mm] 7600Max. total length [mm] 8000Moment of inertia [kgm²] 0.004WeightsBasic without travel [kg] 7.8Travel per 100 mm [kg] 0.98Slide plate 210 mm [kg] 2.75Slide plate 270 mm [kg] 3.25
Advantages of profiled rail guide
Linear Axes · toothed-belt Drive
B 80C-ZSS
High load bearing capacity
Long lifetime
High precision
Load Dynamic Fx** [N] 2200 Fy
[N] 1600 Fz
[N] 4000 -Fz
[N] 3000Load torques Dynamic
Mx[Nm] 300
My[Nm] 500 (640)
Mz[Nm] 500 (640)
MAmax[Nm] 75.3
** Maximum value = Depending on speed Values in brackets relate to the long slide.
www.comoso.com
![Page 34: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/34.jpg)
w w w . s c h u n k . c o m 195
main views
Assembly connection Drive connection8 Feather key DIN 68859 Useful stroke
Mounting groove for T-nutsL Bolt pitch circleT Change of dimension with optional cover tape
Linear Axes · toothed-belt Drive
B 80C-ZSS
Long slide
9 Useful strokeT Change of dimension with optional cover tape
8 Feather key
Drive journal connection dimensions
www.comoso.com
![Page 35: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/35.jpg)
w w w . s c h u n k . c o m196
Linear Axes · toothed-belt Drive
B 80C-ZSS
mountingProfile ZSS
The profile can be secured either using T-nuts or mounting strips.
Designation Order designation ID no.T-nut NS3 0331406T-nut RM4 0331426Mounting strip BL2 0331401
motor flange schematic diagram
The table shows the relevant dimension C of the standard couplings. For dimension A refer to drive journal connection dimensions, for dimension B refer to corresponding motor dimension sheet, dimension L may differ in individual cases.Different drive solutions can be attached to our axes.SCHUNK can supply you with the right motor flange and coupling for your drive.
Because of the different thermal behavior of motors, we recommend that the drive solution is tested by the motor manufacturer.
L = A + B + C
Specific mass [kg/m] 5.92Planar dimension [mm²] 2191Planar moment of inertia ly [mm4] 1376276Planar moment of inertia lz [mm4] 1772609Load torque Wy [mm³] 30375Load torque Wz [mm³] 44315
More detailed information on pedestal bearings, connection shafts and bevel gears can be found in the "OPTIONS for System HSB" section of the catalog.
A Mounting strip T T-nut on base side
www.comoso.com
![Page 36: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/36.jpg)
w w w . s c h u n k . c o m 197
Linear Axes · toothed-belt Drive
B 80C-ZSS
Lubrication connections
Limit switch selectionLimit switch position
T Standard lubrication connection
Standard connectionLubrication nipple M8x1
If the lubrication connection has a different seat, this must be defined in the order text.
Drive shafts
Depending on the axis application, the drive shaft seat may need to be defined in the order text. Particularly with axis combinations and mechanical synchronization, multiple drive shafts - some of them continuous shafts - are required.
T Limit switch standard position
Two EO2 switches are used as limit switches and an RS2 as the reference switch as standard.
The positions and dimensions of limit switches, switching lugs, and mounting components may vary depending on the application and the selected limit switches. Please contact us for assistance.
More detailed information on pedestal bearings, connection shafts and bevel gears can be found in the "OPTIONS for System HSB" section of the catalog.
Designation Order designation ID no.Inductive limit switch, opener, 2 m cable EO2 0331410Inductive limit switch, opener, 10 m cable EO10 0331412Inductive limit switch, closer, 2 m cable ES2 0331411Inductive limit switch, closer, 10 m cable ES10 0331413Mechanical limit switch (Siemens), opener EMS 0331414Mechanical limit switch (Balluff), opener EMB 0331415
www.comoso.com
![Page 37: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/37.jpg)
w w w . s c h u n k . c o m198
technical data
Loads and load torques
Designation B 100-ZRS B 100-ZSSMax. travel speed [m/s] 8 5Repeat accuracy [mm] ± 0.08 ± 0.08Max. acceleration [m/s²] 40 40Idle torque [Nm] 2.5 2.5DriveDrive element Toothed belt 40 AT 10 40 AT 10Travel per revolution [mm] 200 200Maximum stroke [mm] 7420 7420Max. total length [mm] 7900 7900Moment of inertia [kgm²] 0.013 0.0126WeightsBasic without travel [kg] 9.5 9.1Travel per 100 mm [kg] 1.1 1.45Slide plate 280 mm [kg] 4.1 3.8Slide plate 400 mm [kg] 5.85 5.43
Advantages of profiled rail guide
Linear Axes · toothed-belt Drive
B 100-ZRS/-ZSS
High load bearing capacity
Long lifetime
High precision
Load ZRS dynamic ZSS dynamic Fx** [N] 2800 2800 Fy
[N] 1000 1000 Fz
[N] 2500 3000 -Fz
[N] 1200 2000Load torques ZRS dynamic ZSS dynamic
Mx[Nm] 200 200
My[Nm] 250 (350) 300 (420)
Mz[Nm] 200 (280) 300 (420)
MAmax[Nm] 91.6 91.6
** Maximum value = Depending on speed Values in brackets relate to the long slide.
High maximum moments due to optimum force transmission to the profile
Long stroke lengths can be achieved with no problems
Life-time lubricated rollers for easy maintenance use
Smooth, low-noise running
Advantages of roller guide
www.comoso.com
![Page 38: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/38.jpg)
w w w . s c h u n k . c o m 199
main views
Assembly connection Drive connection8 Feather key DIN 68859 Useful stroke
Mounting groove for T-nutsL Bolt pitch circleT Change of dimension with optional cover tape
Linear Axes · toothed-belt Drive
B 100-ZRS/-ZSS
8 Feather key
Drive journal connection dimensionsLong slide
9 Useful strokeT Change of dimension with optional cover tape
www.comoso.com
![Page 39: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/39.jpg)
w w w . s c h u n k . c o m200
The profile can be secured either using T-nuts or mounting strips.
Designation Order designation ID no.T-nut NS1 0331404T-nut NS2 0331405T-nut NS4 0331407T-nut RM2 0331425T-nut RM4 0331426Mounting strip BL2 0331401
Linear Axes · toothed-belt Drive
B 100-ZRS/-ZSS
mountingProfile ZRS/ZSS
motor flange schematic diagram
The table shows the relevant dimension C of the standard couplings. For dimension A refer to drive journal connection dimensions, for dimension B refer to corresponding motor dimension sheet, dimension L may differ in individual cases.Different drive solutions can be attached to our axes.SCHUNK can supply you with the right motor flange and coupling for your drive.
Because of the different thermal behavior of motors, we recommend that the drive solution is tested by the motor manufacturer.
L = A + B + C
Specific mass [kg/m] 7.97Planar dimension [mm²] 2950Planar moment of inertia ly [mm4] 1782959Planar moment of inertia lz [mm4] 3507213Load torque Wy [mm³] 40598Load torque Wz [mm³] 70137
More detailed information on pedestal bearings, connection shafts and bevel gears can be found in the "OPTIONS for System HSB" section of the catalog.
A Mounting strip T T-nut on base side K Side T-nut
www.comoso.com
![Page 40: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/40.jpg)
w w w . s c h u n k . c o m 201
Linear Axes · toothed-belt Drive
B 100-ZRS/-ZSS
Lubrication connections
Limit switch selectionLimit switch position
T Standard lubrication connection
Standard connectionLubrication nipple M8x1
If the lubrication connection has a different seat, this must be defined in the order text.
Drive shafts
Depending on the axis application, the drive shaft seat may need to be defined in the order text. Particularly with axis combinations and mechanical synchronization, multiple drive shafts - some of them continuous shafts - are required.
T Limit switch standard position
Two EO2 switches are used as limit switches and an RS2 as the reference switch as standard.
The positions and dimensions of limit switches, switching lugs, and mounting components may vary depending on the application and the selected limit switches. Please contact us for assistance.
More detailed information on pedestal bearings, connection shafts and bevel gears can be found in the "OPTIONS for System HSB" section of the catalog.
Designation Order designation ID no.Inductive limit switch, opener, 2 m cable EO2 0331410Inductive limit switch, opener, 10 m cable EO10 0331412Inductive limit switch, closer, 2 m cable ES2 0331411Inductive limit switch, closer, 10 m cable ES10 0331413Mechanical limit switch (Siemens), opener EMS 0331414Mechanical limit switch (Balluff), opener EMB 0331415
www.comoso.com
![Page 41: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/41.jpg)
w w w . s c h u n k . c o m202
technical data
Loads and load torques
Designation B 100D-ZSSMax. travel speed [m/s] 5Repeat accuracy [mm] ± 0.08Max. acceleration [m/s²] 60Idle torque [Nm] 2.5DriveDrive element Toothed belt 40 AT 10-ETravel per revolution [mm] 160Maximum stroke [mm] 7720Max. total length [mm] 8100Moment of inertia [kgm²] 0.0028WeightsBasic without travel [kg] 6.8Travel per 100 mm [kg] 0.75Slide plate 210 mm [kg] 3.5Slide plate 270 mm [kg] 4.1
Advantages of profiled rail guide
Linear Axes · toothed-belt Drive
B 100D-ZSS
High load bearing capacity
Long lifetime
High precision
Load Dynamic Fx** [N] 1500 Fy
[N] 1800 Fz
[N] 4000 -Fz
[N] 3000Load torques Dynamic
Mx[Nm] 350
My[Nm] 750 (1000)
Mz[Nm] 750 (1000)
MAmax[Nm] 40.7
** Maximum value = Depending on speed Values in brackets relate to the long slide.
www.comoso.com
![Page 42: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/42.jpg)
w w w . s c h u n k . c o m 203
main views
Assembly connection Drive connection8 Feather key DIN 68859 Useful stroke
Mounting groove for T-nutsL Bolt pitch circle
Linear Axes · toothed-belt Drive
B 100D-ZSS
Long slide
9 Useful stroke 8 Feather key
Drive journal connection dimensions
www.comoso.com
![Page 43: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/43.jpg)
w w w . s c h u n k . c o m204
Linear Axes · toothed-belt Drive
B 100D-ZSS
mountingProfile ZSS
The profile can be secured either using T-nuts or mounting strips.
Designation Order designation ID no.T-nut NS4 0331407T-nut NS8 0331420T-nut NS9 0331421T-nut NS10 0331422T-nut NS12 0331424Mounting strip BL5 0331419
motor flange schematic diagram
The table shows the relevant dimension C of the standard couplings. For dimension A refer to drive journal connection dimensions, for dimension B refer to corresponding motor dimension sheet, dimension L may differ in individual cases.Different drive solutions can be attached to our axes.SCHUNK can supply you with the right motor flange and coupling for your drive.
Because of the different thermal behavior of motors, we recommend that the drive solution is tested by the motor manufacturer.
L = A + B + C
Specific mass [kg/m] 4.87Planar dimension [mm²] 1804Planar moment of inertia ly [mm4] 917779Planar moment of inertia lz [mm4] 2328911Load torque Wy [mm³] 23869Load torque Wz [mm³] 46578
More detailed information on pedestal bearings, connection shafts and bevel gears can be found in the "OPTIONS for System HSB" section of the catalog.
A Mounting strip T T-nut on base side K Side T-nut
www.comoso.com
![Page 44: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/44.jpg)
w w w . s c h u n k . c o m 205
Linear Axes · toothed-belt Drive
B 100D-ZSS
Lubrication connections
Limit switch selectionLimit switch position
T Standard lubrication connection
Standard connectionLubrication nipple M8x1
If the lubrication connection has a different seat, this must be defined in the order text.
Drive shafts
Depending on the axis application, the drive shaft seat may need to be defined in the order text. Particularly with axis combinations and mechanical synchronization, multiple drive shafts - some of them continuous shafts - are required.
T Limit switch standard position
Two EO2 switches are used as limit switches and an RS2 as the reference switch as standard.
The positions and dimensions of limit switches, switching lugs, and mounting components may vary depending on the application and the selected limit switches. Please contact us for assistance.
More detailed information on pedestal bearings, connection shafts and bevel gears can be found in the "OPTIONS for System HSB" section of the catalog.
Designation Order designation ID no.Inductive limit switch, opener, 2 m cable EO2 0331410Inductive limit switch, opener, 10 m cable EO10 0331412Inductive limit switch, closer, 2 m cable ES2 0331411Inductive limit switch, closer, 10 m cable ES10 0331413Mechanical limit switch (Siemens), opener EMS 0331414Mechanical limit switch (Balluff), opener EMB 0331415
www.comoso.com
![Page 45: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/45.jpg)
w w w . s c h u n k . c o m206
technical data
Loads and load torques
Designation B 100D-ASSMax. travel speed [m/s] 5Repeat accuracy [mm] ± 0.08Max. acceleration [m/s²] 60Idle torque [Nm] 2.5DriveDrive element Toothed belt 40 AT 10-ETravel per revolution [mm] 240Maximum stroke [mm] 7680Max. total length [mm] 8100Moment of inertia [kgm²] 0.012WeightsBasic without travel [kg] 14.0Travel per 100 mm [kg] 0.9Slide drive 400 mm [kg] 8.6
Advantages of profiled rail guide
Linear Axes · toothed-belt Drive
B 100D-ASS
High load bearing capacity
Long lifetime
High precision
Load Dynamic Fx** [N] 2200 Fy
[N] 1800 Fz
[N] 4000 -Fz
[N] 3000Load torques Dynamic
Mx[Nm] 350
My[Nm] 950
Mz[Nm] 950
MAmax[Nm] 86.5
** Maximum value = Depending on speed Values in brackets relate to the long slide.
www.comoso.com
![Page 46: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/46.jpg)
w w w . s c h u n k . c o m 207
main views
Linear unit connection Assembly connection Drive connection8 Feather key DIN 68859 Useful stroke
Mounting groove for T-nutsL Bolt pitch circle
Linear Axes · toothed-belt Drive
B 100D-ASS
8 Feather key
Drive journal connection dimensions
www.comoso.com
![Page 47: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/47.jpg)
w w w . s c h u n k . c o m208
Linear Axes · toothed-belt Drive
B 100D-ASS
mountingProfile ASS
The profile can be secured either using T-nuts or mounting strips.
Designation Order designation ID no.T-nut NS4 0331407T-nut NS8 0331420T-nut NS9 0331421T-nut NS10 0331422T-nut NS12 0331424Mounting strip BL5 0331419
motor flange schematic diagram
The table shows the relevant dimension C of the standard couplings. For dimension A refer to drive journal connection dimensions, for dimension B refer to corresponding motor dimension sheet, dimension L may differ in individual cases.Different drive solutions can be attached to our axes.SCHUNK can supply you with the right motor flange and coupling for your drive.
Because of the different thermal behavior of motors, we recommend that the drive solution is tested by the motor manufacturer.
L = A + B + C
Specific mass [kg/m] 4.87Planar dimension [mm²] 1804Planar moment of inertia ly [mm4] 917779Planar moment of inertia lz [mm4] 2328911Load torque Wy [mm³] 23869Load torque Wz [mm³] 46578
More detailed information on pedestal bearings, connection shafts and bevel gears can be found in the "OPTIONS for System HSB" section of the catalog.
A Mounting strip T T-nut on base side K Side T-nut
www.comoso.com
![Page 48: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/48.jpg)
w w w . s c h u n k . c o m 209
Linear Axes · toothed-belt Drive
B 100D-ASS
Lubrication connections
Limit switch selectionLimit switch position
T Standard lubrication connection
Standard connectionLubrication nipple M8x1
If the lubrication connection has a different seat, this must be defined in the order text.
Drive shafts
Depending on the axis application, the drive shaft seat may need to be defined in the order text. Particularly with axis combinations and mechanical synchronization, multiple drive shafts - some of them continuous shafts - are required.
T Limit switch standard position
Two EO2 switches are used as limit switches and an RS2 as the reference switch as standard.
The positions and dimensions of limit switches, switching lugs, and mounting components may vary depending on the application and the selected limit switches. Please contact us for assistance.
More detailed information on pedestal bearings, connection shafts and bevel gears can be found in the "OPTIONS for System HSB" section of the catalog.
Designation Order designation ID no.Inductive limit switch, opener, 2 m cable EO2 0331410Inductive limit switch, opener, 10 m cable EO10 0331412Inductive limit switch, closer, 2 m cable ES2 0331411Inductive limit switch, closer, 10 m cable ES10 0331413Mechanical limit switch (Siemens), opener EMS 0331414Mechanical limit switch (Balluff), opener EMB 0331415
www.comoso.com
![Page 49: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/49.jpg)
w w w . s c h u n k . c o m210
technical data
Loads and load torques
Designation B 110-ZRS B 110-ZSSMax. travel speed [m/s] 8 5Repeat accuracy [mm] ± 0.08 ± 0.08Max. acceleration [m/s²] 60 60Idle torque [Nm] 3.5 3.5DriveDrive element Toothed belt 50 ATL 10 50 ATL 10Travel per revolution [mm] 300 300Maximum stroke [mm] 7520 7520Max. total length [mm] 8100 8100Moment of inertia [kgm²] 0.0180 0.0160WeightsBasic without travel [kg] 15.7 18.0Travel per 100 mm [kg] 1.5 2.1Slide plate 320 mm [kg] 4.8 5.2Slide plate 500 mm [kg] 7.5 8.2
Advantages of profiled rail guide
Linear Axes · toothed-belt Drive
B 110-ZRS/-ZSS
High load bearing capacity
Long lifetime
High precision
Load ZRS dynamic ZSS dynamic Fx** [N] 4000 4000 Fy
[N] 2000 3000 Fz
[N] 5000 8000 -Fz
[N] 2500 4000Load torques ZRS dynamic ZSS dynamic
Mx[Nm] 300 400
My[Nm] 600 (800) 800 (1200)
Mz[Nm] 450 (550) 600 (800)
MAmax[Nm] 194.5 194.5
** Maximum value = Depending on speed Values in brackets relate to the long slide.
High maximum moments due to optimum force transmission to the profile
Long stroke lengths can be achieved with no problems
Life-time lubricated rollers for easy maintenance use
Smooth, low-noise running
Advantages of roller guide
www.comoso.com
![Page 50: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/50.jpg)
w w w . s c h u n k . c o m 211
main views
Assembly connection Drive connection8 Feather key DIN 68859 Useful stroke
Mounting groove for T-nutsL Bolt pitch circle
Linear Axes · toothed-belt Drive
B 110-ZRS/-ZSS
8 Feather key
Drive journal connection dimensionsLong slide
9 Useful stroke
www.comoso.com
![Page 51: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/51.jpg)
w w w . s c h u n k . c o m212
Linear Axes · toothed-belt Drive
B 110-ZRS/-ZSS
Profile ZRS
motor flange schematic diagram
The table shows the relevant dimension C of the standard couplings. For dimension A refer to drive journal connection dimensions, for dimension B refer to corresponding motor dimension sheet, dimension L may differ in individual cases.Different drive solutions can be attached to our axes.SCHUNK can supply you with the right motor flange and coupling for your drive.
Because of the different thermal behavior of motors, we recommend that the drive solution is tested by the motor manufacturer.
L = A + B + C
Specific mass [kg/m] 10.69Planar dimension [mm²] 3961Planar moment of inertia ly [mm4] 5114812Planar moment of inertia lz [mm4] 6177042Load torque Wy [mm³] 87307Load torque Wz [mm³] 111528
mounting
The profile can be secured either using T-nuts or mounting strips.
Designation Order designation ID no.T-nut NS4 0331407T-nut NS10 0331422T-nut NS11 0331429T-nut RM2 0331425T-nut RM6 0331427Mounting strip BL2 0331401
Profile ZSS
Specific mass [kg/m] 10.54Planar dimension [mm²] 3902Planar moment of inertia ly [mm4] 4974348Planar moment of inertia lz [mm4] 5898662Load torque Wy [mm³] 79469Load torque Wz [mm³] 106973
More detailed information on pedestal bearings, connection shafts and bevel gears can be found in the "OPTIONS for System HSB" section of the catalog.
A Mounting strip T T-nut on base side K Side T-nut
www.comoso.com
![Page 52: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/52.jpg)
w w w . s c h u n k . c o m 213
Linear Axes · toothed-belt Drive
B 110-ZRS/-ZSS
Lubrication connections
Limit switch selectionLimit switch position
T Standard lubrication connection
Standard connectionLubrication nipple M8x1
If the lubrication connection has a different seat, this must be defined in the order text.
Drive shafts
Depending on the axis application, the drive shaft seat may need to be defined in the order text. Particularly with axis combinations and mechanical synchronization, multiple drive shafts - some of them continuous shafts - are required.
T Limit switch standard position
Two EO2 switches are used as limit switches and an RS2 as the reference switch as standard.
The positions and dimensions of limit switches, switching lugs, and mounting components may vary depending on the application and the selected limit switches. Please contact us for assistance.
More detailed information on pedestal bearings, connection shafts and bevel gears can be found in the "OPTIONS for System HSB" section of the catalog.
Designation Order designation ID no.Inductive limit switch, opener, 2 m cable EO2 0331410Inductive limit switch, opener, 10 m cable EO10 0331412Inductive limit switch, closer, 2 m cable ES2 0331411Inductive limit switch, closer, 10 m cable ES10 0331413Mechanical limit switch (Siemens), opener EMS 0331414Mechanical limit switch (Balluff), opener EMB 0331415
www.comoso.com
![Page 53: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/53.jpg)
w w w . s c h u n k . c o m214
technical data
Loads and load torques
Designation B 110-ARS B 110-ASSMax. travel speed [m/s] 8 5Repeat accuracy [mm] ± 0.08 ± 0.08Max. acceleration [m/s²] 60 60Idle torque [Nm] 3.5 3.5DriveDrive element Toothed belt 50 ATL 10 50 ATL 10Travel per revolution [mm] 300 300Maximum stroke [mm] 7440 7440Max. total length [mm] 8100 8100Moment of inertia [kgm²] 0.035 0.037WeightsBasic without travel [kg] 27.00 29.0Travel per 100 mm [kg] 1.2 1.4Slide drive 400 mm [kg] 15.00 16.00
Advantages of profiled rail guide
Linear Axes · toothed-belt Drive
B 110-ARS/-ASS
High load bearing capacity
Long lifetime
High precision
Load ARS dynamic ASS dynamic Fx** [N] 2000 2000 Fy
[N] 2000 3000 Fz
[N] 5000 8000 -Fz
[N] 2500 4000Load torques ARS dynamic ASS dynamic
Mx[Nm] 300 400
My[Nm] 600 800
Mz[Nm] 450 600
MAmax[Nm] 99.0 99.0
** Maximum value = Depending on speed Values in brackets relate to the long slide.
High maximum moments due to optimum force transmission to the profile
Long stroke lengths can be achieved with no problems
Life-time lubricated rollers for easy maintenance use
Smooth, low-noise running
Advantages of roller guide
www.comoso.com
![Page 54: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/54.jpg)
w w w . s c h u n k . c o m 215
main views
Linear unit connection Assembly connection Drive connection8 Feather key DIN 68859 Useful stroke
Mounting groove for T-nutsL Bolt pitch circle
Linear Axes · toothed-belt Drive
B 110-ARS/-ASS
8 Feather key
Drive journal connection dimensions
www.comoso.com
![Page 55: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/55.jpg)
w w w . s c h u n k . c o m216
Linear Axes · toothed-belt Drive
B 110-ARS/-ASS
Profile ARS
motor flange schematic diagram
The table shows the relevant dimension C of the standard couplings. For dimension A refer to drive journal connection dimensions, for dimension B refer to corresponding motor dimension sheet, dimension L may differ in individual cases.Different drive solutions can be attached to our axes.SCHUNK can supply you with the right motor flange and coupling for your drive.
Because of the different thermal behavior of motors, we recommend that the drive solution is tested by the motor manufacturer.
L = A + B + C
Specific mass [kg/m] 10.69Planar dimension [mm²] 3961Planar moment of inertia ly [mm4] 5114812Planar moment of inertia lz [mm4] 6177042Load torque Wy [mm³] 87307Load torque Wz [mm³] 111528
mounting
The profile can be secured either using T-nuts or mounting strips.
Designation Order designation ID no.T-nut NS4 0331407T-nut NS10 0331422T-nut NS11 0331429T-nut RM2 0331425T-nut RM6 0331427Mounting strip BL2 0331401
Profile ASS
Specific mass [kg/m] 10.54Planar dimension [mm²] 3902Planar moment of inertia ly [mm4] 4974348Planar moment of inertia lz [mm4] 5898662Load torque Wy [mm³] 79469Load torque Wz [mm³] 106973
More detailed information on pedestal bearings, connection shafts and bevel gears can be found in the "OPTIONS for System HSB" section of the catalog.
A Mounting strip T T-nut on base side K Side T-nut
www.comoso.com
![Page 56: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/56.jpg)
w w w . s c h u n k . c o m 217
Linear Axes · toothed-belt Drive
B 110-ARS/-ASS
Lubrication connections
Limit switch selectionLimit switch position
T Standard lubrication connection
Standard connectionLubrication nipple M8x1
If the lubrication connection has a different seat, this must be defined in the order text.
Drive shafts
Depending on the axis application, the drive shaft seat may need to be defined in the order text. Particularly with axis combinations and mechanical synchronization, multiple drive shafts - some of them continuous shafts - are required.
T Limit switch standard position
Two EO2 switches are used as limit switches and an RS2 as the reference switch as standard.
The positions and dimensions of limit switches, switching lugs, and mounting components may vary depending on the application and the selected limit switches. Please contact us for assistance.
More detailed information on pedestal bearings, connection shafts and bevel gears can be found in the "OPTIONS for System HSB" section of the catalog.
Designation Order designation ID no.Inductive limit switch, opener, 2 m cable EO2 0331410Inductive limit switch, opener, 10 m cable EO10 0331412Inductive limit switch, closer, 2 m cable ES2 0331411Inductive limit switch, closer, 10 m cable ES10 0331413Mechanical limit switch (Siemens), opener EMS 0331414Mechanical limit switch (Balluff), opener EMB 0331415
www.comoso.com
![Page 57: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/57.jpg)
w w w . s c h u n k . c o m218
technical data
Loads and load torques
Designation B 120-ZRS B 120-ZSSMax. travel speed [m/s] 8 5Repeat accuracy [mm] ± 0.08 ± 0.08Max. acceleration [m/s²] 60 60Idle torque [Nm] 3.2 3.2DriveDrive element Toothed belt 50 ATL 10 50 ATL 10Travel per revolution [mm] 240 240Maximum stroke [mm] 7520 7520Max. total length [mm] 8100 8100Moment of inertia [kgm²] 0.015 0.016WeightsBasic without travel [kg] 12.5 13.0Travel per 100 mm [kg] 1.3 1.7Slide plate 320 mm [kg] 6.0 6.5Slide plate 500 mm [kg] 9.4 10.2
Advantages of profiled rail guide
Linear Axes · toothed-belt Drive
B 120-ZRS/-ZSS
High load bearing capacity
Long lifetime
High precision
Load ZRS dynamic ZSS dynamic Fx** [N] 4000 4000 Fy
[N] 2500 3000 Fz
[N] 6000 8000 -Fz
[N] 3000 4000Load torques ZRS dynamic ZSS dynamic
Mx[Nm] 350 400
My[Nm] 700 (1000) 1200 (1500)
Mz[Nm] 700 (1000) 600 (800)
MAmax[Nm] 156.0 156.0
** Maximum value = Depending on speed Values in brackets relate to the long slide.
High maximum moments due to optimum force transmission to the profile
Long stroke lengths can be achieved with no problems
Life-time lubricated rollers for easy maintenance use
Smooth, low-noise running
Advantages of roller guide
www.comoso.com
![Page 58: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/58.jpg)
w w w . s c h u n k . c o m 219
main views
Assembly connection Drive connection8 Feather key DIN 68859 Useful stroke
Mounting groove for T-nutsL Bolt pitch circle
Linear Axes · toothed-belt Drive
B 120-ZRS/-ZSS
8 Feather key
Drive journal connection dimensionsLong slide
9 Useful stroke
www.comoso.com
![Page 59: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/59.jpg)
w w w . s c h u n k . c o m220
mounting
The profile can be secured either using T-nuts or mounting strips.
Designation Order designation ID no.T-nut NS1 0331404T-nut NS2 0331405T-nut NS4 0331407T-nut NS10 0331422T-nut RM2 0331425T-nut RM6 0331427Mounting strip BL1 0331400
Linear Axes · toothed-belt Drive
B 120-ZRS/-ZSS
Profile ZRS/ZSS
motor flange schematic diagram
The table shows the relevant dimension C of the standard couplings. For dimension A refer to drive journal connection dimensions, for dimension B refer to corresponding motor dimension sheet, dimension L may differ in individual cases.Different drive solutions can be attached to our axes.SCHUNK can supply you with the right motor flange and coupling for your drive.
Because of the different thermal behavior of motors, we recommend that the drive solution is tested by the motor manufacturer.
L = A + B + C
Specific mass [kg/m] 10.47Planar dimension [mm²] 3876Planar moment of inertia ly [mm4] 3095671Planar moment of inertia lz [mm4] 7114115Load torque Wy [mm³] 62753Load torque Wz [mm³] 118478
More detailed information on pedestal bearings, connection shafts and bevel gears can be found in the "OPTIONS for System HSB" section of the catalog.
A Mounting strip T T-nut on base side K Side T-nut
www.comoso.com
![Page 60: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/60.jpg)
w w w . s c h u n k . c o m 221
Linear Axes · toothed-belt Drive
B 120-ZRS/-ZSS
Lubrication connections
Limit switch selectionLimit switch position
T Standard lubrication connection
Standard connectionLubrication nipple M8x1
If the lubrication connection has a different seat, this must be defined in the order text.
Drive shafts
Depending on the axis application, the drive shaft seat may need to be defined in the order text. Particularly with axis combinations and mechanical synchronization, multiple drive shafts - some of them continuous shafts - are required.
T Limit switch standard position
Two EO2 switches are used as limit switches and an RS2 as the reference switch as standard.
The positions and dimensions of limit switches, switching lugs, and mounting components may vary depending on the application and the selected limit switches. Please contact us for assistance.
More detailed information on pedestal bearings, connection shafts and bevel gears can be found in the "OPTIONS for System HSB" section of the catalog.
Designation Order designation ID no.Inductive limit switch, opener, 2 m cable EO2 0331410Inductive limit switch, opener, 10 m cable EO10 0331412Inductive limit switch, closer, 2 m cable ES2 0331411Inductive limit switch, closer, 10 m cable ES10 0331413Mechanical limit switch (Siemens), opener EMS 0331414Mechanical limit switch (Balluff), opener EMB 0331415
www.comoso.com
![Page 61: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/61.jpg)
w w w . s c h u n k . c o m222
technical data
Loads and load torques
Designation B 140-ZRS B 140-ZSSMax. travel speed [m/s] 8 5Repeat accuracy [mm] ± 0.08 ± 0.08Max. acceleration [m/s²] 60 60Idle torque [Nm] 3.5 3.5DriveDrive element Toothed belt 50 AT 10-E 50 AT 10-ETravel per revolution [mm] 220 220Maximum stroke [mm] 7540 7540Max. total length [mm] 8100 8100Moment of inertia [kgm²] 0.019 0.020WeightsBasic without travel [kg] 13.5 15.0Travel per 100 mm [kg] 1.3 1.7Slide plate 320 mm [kg] 7.0 7.5Slide plate 500 mm [kg] 11.0 11.7
Advantages of profiled rail guide
Linear Axes · toothed-belt Drive
B 140-ZRS/-ZSS
High load bearing capacity
Long lifetime
High precision
Load ZRS dynamic ZSS dynamic Fx** [N] 4000 4000 Fy
[N] 2500 2500 Fz
[N] 5000 6000 -Fz
[N] 3000 4000Load torques ZRS dynamic ZSS dynamic
Mx[Nm] 350 500
My[Nm] 700 (900) 1000 (1300)
Mz[Nm] 700 (900) 1000 1300)
MAmax[Nm] 143.6 143.6
** Maximum value = Depending on speed Values in brackets relate to the long slide.
High maximum moments due to optimum force transmission to the profile
Long stroke lengths can be achieved with no problems
Life-time lubricated rollers for easy maintenance use
Smooth, low-noise running
Advantages of roller guide
www.comoso.com
![Page 62: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/62.jpg)
w w w . s c h u n k . c o m 223
main views
Assembly connection Drive connection8 Feather key DIN 68859 Useful stroke
Mounting groove for T-nutsL Bolt pitch circle
Linear Axes · toothed-belt Drive
B 140-ZRS/-ZSS
8 Feather key
Drive journal connection dimensionsLong slide
9 Useful stroke
www.comoso.com
![Page 63: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/63.jpg)
w w w . s c h u n k . c o m224
mounting
The profile can be secured either using T-nuts or mounting strips.
Designation Order designation ID no.T-nut NS1 0331404T-nut NS4 0331407T-nut NS10 0331422T-nut RM2 0331425T-nut RM4 0331426Mounting strip BL6 0331428
Linear Axes · toothed-belt Drive
B 140-ZRS/-ZSS
Profile ZRS/ZSS
motor flange schematic diagram
The table shows the relevant dimension C of the standard couplings. For dimension A refer to drive journal connection dimensions, for dimension B refer to corresponding motor dimension sheet, dimension L may differ in individual cases.Different drive solutions can be attached to our axes.SCHUNK can supply you with the right motor flange and coupling for your drive.
Because of the different thermal behavior of motors, we recommend that the drive solution is tested by the motor manufacturer.
L = A + B + C
Specific mass [kg/m] 10.68Planar dimension [mm²] 3955Planar moment of inertia ly [mm4] 3159202Planar moment of inertia lz [mm4] 9975915Load torque Wy [mm³] 69334Load torque Wz [mm³] 184852
More detailed information on pedestal bearings, connection shafts and bevel gears can be found in the "OPTIONS for System HSB" section of the catalog.
A Mounting strip T T-nut on base sideK Side T-nut
www.comoso.com
![Page 64: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/64.jpg)
w w w . s c h u n k . c o m 225
Linear Axes · toothed-belt Drive
B 140-ZRS/-ZSS
Lubrication connections
Limit switch selectionLimit switch position
T Standard lubrication connection
Standard connectionLubrication nipple M8x1
If the lubrication connection has a different seat, this must be defined in the order text.
Drive shafts
Depending on the axis application, the drive shaft seat may need to be defined in the order text. Particularly with axis combinations and mechanical synchronization, multiple drive shafts - some of them continuous shafts - are required.
T Limit switch standard position
Two EO2 switches are used as limit switches and an RS2 as the reference switch as standard.
The positions and dimensions of limit switches, switching lugs, and mounting components may vary depending on the application and the selected limit switches. Please contact us for assistance.
More detailed information on pedestal bearings, connection shafts and bevel gears can be found in the "OPTIONS for System HSB" section of the catalog.
Designation Order designation ID no.Inductive limit switch, opener, 2 m cable EO2 0331410Inductive limit switch, opener, 10 m cable EO10 0331412Inductive limit switch, closer, 2 m cable ES2 0331411Inductive limit switch, closer, 10 m cable ES10 0331413Mechanical limit switch (Siemens), opener EMS 0331414Mechanical limit switch (Balluff), opener EMB 0331415
www.comoso.com
![Page 65: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/65.jpg)
w w w . s c h u n k . c o m226
technical data
Loads and load torques
Designation B 140-ARS B 140-ASSMax. travel speed [m/s] 8 5Repeat accuracy [mm] ± 0.08 ± 0.08Max. acceleration [m/s²] 60 60Idle torque [Nm] 3.5 3.5DriveDrive element Toothed belt 50 AT 10-E 50 AT 10-ETravel per revolution [mm] 220 220Maximum stroke [mm] 7470 7470Max. total length [mm] 8100 8100Moment of inertia [kgm²] 0.035 0.037WeightsBasic without travel [kg] 28.0 30.0Travel per 100 mm [kg] 1.2 1.5Slide drive 380 mm [kg] 13.0 14.0
Advantages of profiled rail guide
Linear Axes · toothed-belt Drive
B 140-ARS/-ASS
High load bearing capacity
Long lifetime
High precision
Load ARS dynamic ASS dynamic Fx** [N] 1800 1800 Fy
[N] 2500 2500 Fz
[N] 5000 6000 -Fz
[N] 3000 4000Load torques ARS dynamic ASS dynamic
Mx[Nm] 1800 1800
My[Nm] 2500 2500
Mz[Nm] 5000 6000
MAmax[Nm] 3000 4000
** Maximum value = Depending on speed Values in brackets relate to the long slide.
High maximum moments due to optimum force transmission to the profile
Long stroke lengths can be achieved with no problems
Life-time lubricated rollers for easy maintenance use
Smooth, low-noise running
Advantages of roller guide
www.comoso.com
![Page 66: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/66.jpg)
w w w . s c h u n k . c o m 227
main views
Linear unit connection Assembly connection Drive connection8 Feather key DIN 68859 Useful stroke
Mounting groove for T-nutsL Bolt pitch circle
Linear Axes · toothed-belt Drive
B 140-ARS/-ASS
8 Feather key
Drive journal connection dimensions
www.comoso.com
![Page 67: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/67.jpg)
w w w . s c h u n k . c o m228
mounting
The profile can be secured either using T-nuts or mounting strips.
Designation Order designation ID no.T-nut NS1 0331404T-nut NS4 0331407T-nut NS10 0331422T-nut RM2 0331425T-nut RM4 0331426Mounting strip BL6 0331428
Linear Axes · toothed-belt Drive
B 140-ARS/-ASS
Profile ARS/ASS
motor flange schematic diagram
The table shows the relevant dimension C of the standard couplings. For dimension A refer to drive journal connection dimensions, for dimension B refer to corresponding motor dimension sheet, dimension L may differ in individual cases.Different drive solutions can be attached to our axes.SCHUNK can supply you with the right motor flange and coupling for your drive.
Because of the different thermal behavior of motors, we recommend that the drive solution is tested by the motor manufacturer.
L = A + B + C
Specific mass [kg/m] 10.68Planar dimension [mm²] 3955Planar moment of inertia ly [mm4] 3159202Planar moment of inertia lz [mm4] 9975915Load torque Wy [mm³] 69334Load torque Wz [mm³] 184852
More detailed information on pedestal bearings, connection shafts and bevel gears can be found in the "OPTIONS for System HSB" section of the catalog.
A Mounting strip T T-nut on base sideK Side T-nut
www.comoso.com
![Page 68: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/68.jpg)
w w w . s c h u n k . c o m 229
Linear Axes · toothed-belt Drive
B 140-ARS/-ASS
Lubrication connections
Limit switch selectionLimit switch position
T Standard lubrication connection
Standard connectionLubrication nipple M8x1
If the lubrication connection has a different seat, this must be defined in the order text.
Drive shafts
Depending on the axis application, the drive shaft seat may need to be defined in the order text. Particularly with axis combinations and mechanical synchronization, multiple drive shafts - some of them continuous shafts - are required.
T Limit switch standard position
Two EO2 switches are used as limit switches and an RS2 as the reference switch as standard.
The positions and dimensions of limit switches, switching lugs, and mounting components may vary depending on the application and the selected limit switches. Please contact us for assistance.
More detailed information on pedestal bearings, connection shafts and bevel gears can be found in the "OPTIONS for System HSB" section of the catalog.
Designation Order designation ID no.Inductive limit switch, opener, 2 m cable EO2 0331410Inductive limit switch, opener, 10 m cable EO10 0331412Inductive limit switch, closer, 2 m cable ES2 0331411Inductive limit switch, closer, 10 m cable ES10 0331413Mechanical limit switch (Siemens), opener EMS 0331414Mechanical limit switch (Balluff), opener EMB 0331415
www.comoso.com
![Page 69: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/69.jpg)
w w w . s c h u n k . c o m230
technical data
Loads and load torques
Designation B 140C-ZSSMax. travel speed [m/s] 5Repeat accuracy [mm] ± 0.08Max. acceleration [m/s²] 60Idle torque [Nm] 3.5DriveDrive element Toothed belt 50 AT 10-ETravel per revolution [mm] 220Maximum stroke [mm] 7470Max. total length [mm] 8100Moment of inertia [kgm²] 0.02WeightsBasic without travel [kg] 15.0Travel per 100 mm [kg] 1.7Slide plate 320 mm [kg] 7.5Slide plate 500 mm [kg] 11.7
Advantages of profiled rail guide
Linear Axes · toothed-belt Drive
B 140C-ZSS
High load bearing capacity
Long lifetime
High precision
Load Dynamic Fx** [N] 4000 Fy
[N] 3200 Fz
[N] 7500 -Fz
[N] 5000Load torques Dynamic
Mx[Nm] 600
My[Nm] 1200 (1700)
Mz[Nm] 1200 (1700)
MAmax[Nm] 143.6
** Maximum value = Depending on speed Values in brackets relate to the long slide.
www.comoso.com
![Page 70: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/70.jpg)
w w w . s c h u n k . c o m 231
main views
Assembly connection Drive connection8 Feather key DIN 68859 Useful stroke
Mounting groove for T-nutsL Bolt pitch circle
Linear Axes · toothed-belt Drive
B 140C-ZSS
Long slide
9 Useful stroke 8 Feather key
Drive journal connection dimensions
www.comoso.com
![Page 71: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/71.jpg)
w w w . s c h u n k . c o m232
Linear Axes · toothed-belt Drive
B 140C-ZSS
mountingProfile ZSS
The profile can be secured either using T-nuts or mounting strips.
Designation Order designation ID no.T-nut NS4 0331407T-nut NS8 0331420T-nut NS9 0331421T-nut NS10 0331422T-nut NS12 0331424Mounting strip BL6 0331428
motor flange schematic diagram
The table shows the relevant dimension C of the standard couplings. For dimension A refer to drive journal connection dimensions, for dimension B refer to corresponding motor dimension sheet, dimension L may differ in individual cases.Different drive solutions can be attached to our axes.SCHUNK can supply you with the right motor flange and coupling for your drive.
Because of the different thermal behavior of motors, we recommend that the drive solution is tested by the motor manufacturer.
L = A + B + C
Specific mass [kg/m] 10.11Planar dimension [mm²] 3743Planar moment of inertia ly [mm4] 3127894Planar moment of inertia lz [mm4] 9071334Load torque Wy [mm³] 67067Load torque Wz [mm³] 129589
More detailed information on pedestal bearings, connection shafts and bevel gears can be found in the "OPTIONS for System HSB" section of the catalog.
A Mounting strip T T-nut on base sideK Side T-nut
www.comoso.com
![Page 72: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/72.jpg)
w w w . s c h u n k . c o m 233
Linear Axes · toothed-belt Drive
B 140C-ZSS
Lubrication connections
Limit switch selectionLimit switch position
T Standard lubrication connection
Standard connectionLubrication nipple M8x1
If the lubrication connection has a different seat, this must be defined in the order text.
Drive shafts
Depending on the axis application, the drive shaft seat may need to be defined in the order text. Particularly with axis combinations and mechanical synchronization, multiple drive shafts - some of them continuous shafts - are required.
T Limit switch standard position
Two EO2 switches are used as limit switches and an RS2 as the reference switch as standard.
The positions and dimensions of limit switches, switching lugs, and mounting components may vary depending on the application and the selected limit switches. Please contact us for assistance.
More detailed information on pedestal bearings, connection shafts and bevel gears can be found in the "OPTIONS for System HSB" section of the catalog.
Designation Order designation ID no.Inductive limit switch, opener, 2 m cable EO2 0331410Inductive limit switch, opener, 10 m cable EO10 0331412Inductive limit switch, closer, 2 m cable ES2 0331411Inductive limit switch, closer, 10 m cable ES10 0331413Mechanical limit switch (Siemens), opener EMS 0331414Mechanical limit switch (Balluff), opener EMB 0331415
www.comoso.com
![Page 73: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/73.jpg)
w w w . s c h u n k . c o m234
technical data
Loads and load torques
Designation B 140C-ASSMax. travel speed [m/s] 5Repeat accuracy [mm] ± 0.08Max. acceleration [m/s²] 60Idle torque [Nm] 3.5DriveDrive element Toothed belt 50 AT 10-ETravel per revolution [mm] 220Maximum stroke [mm] 7470Max. total length [mm] 8100Moment of inertia [kgm²] 0.037WeightsBasic without travel [kg] 30.0Travel per 100 mm [kg] 1.5Slide drive 380 mm [kg] 14.0
Advantages of profiled rail guide
Linear Axes · toothed-belt Drive
B 140C-ASS
High load bearing capacity
Long lifetime
High precision
Load Dynamic Fx** [N] 1800 Fy
[N] 3200 Fz
[N] 7500 -Fz
[N] 5000Load torques Dynamic
Mx[Nm] 600
My[Nm] 1200
Mz[Nm] 1200
MAmax[Nm] 99.0
** Maximum value = Depending on speed Values in brackets relate to the long slide.
www.comoso.com
![Page 74: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/74.jpg)
w w w . s c h u n k . c o m 235
main views
Linear unit connection Assembly connection Drive connection8 Feather key DIN 68859 Useful stroke
Mounting groove for T-nutsL Bolt pitch circle
Linear Axes · toothed-belt Drive
B 140C-ASS
8 Feather key
Drive journal connection dimensions
www.comoso.com
![Page 75: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/75.jpg)
w w w . s c h u n k . c o m236
Linear Axes · toothed-belt Drive
B 140C-ASS
mountingProfile ASS
motor flange schematic diagram
The table shows the relevant dimension C of the standard couplings. For dimension A refer to drive journal connection dimensions, for dimension B refer to corresponding motor dimension sheet, dimension L may differ in individual cases.Different drive solutions can be attached to our axes.SCHUNK can supply you with the right motor flange and coupling for your drive.
Because of the different thermal behavior of motors, we recommend that the drive solution is tested by the motor manufacturer.
L = A + B + C
Specific mass [kg/m] 10.11Planar dimension [mm²] 3743Planar moment of inertia ly [mm4] 3127894Planar moment of inertia lz [mm4] 9071334Load torque Wy [mm³] 67067Load torque Wz [mm³] 129589
More detailed information on pedestal bearings, connection shafts and bevel gears can be found in the "OPTIONS for System HSB" section of the catalog.
The profile can be secured either using T-nuts or mounting strips.
Designation Order designation ID no.T-nut NS4 0331407T-nut NS8 0331420T-nut NS9 0331421T-nut NS10 0331422T-nut NS12 0331424Mounting strip BL6 0331428
A Mounting strip T T-nut on base sideK Side T-nut
www.comoso.com
![Page 76: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/76.jpg)
w w w . s c h u n k . c o m 237
Linear Axes · toothed-belt Drive
B 140C-ASS
Lubrication connections
Limit switch selectionLimit switch position
T Standard lubrication connection
Standard connectionLubrication nipple M8x1
If the lubrication connection has a different seat, this must be defined in the order text.
Drive shafts
Depending on the axis application, the drive shaft seat may need to be defined in the order text. Particularly with axis combinations and mechanical synchronization, multiple drive shafts - some of them continuous shafts - are required.
T Limit switch standard position
Two EO2 switches are used as limit switches and an RS2 as the reference switch as standard.
The positions and dimensions of limit switches, switching lugs, and mounting components may vary depending on the application and the selected limit switches. Please contact us for assistance.
More detailed information on pedestal bearings, connection shafts and bevel gears can be found in the "OPTIONS for System HSB" section of the catalog.
Designation Order designation ID no.Inductive limit switch, opener, 2 m cable EO2 0331410Inductive limit switch, opener, 10 m cable EO10 0331412Inductive limit switch, closer, 2 m cable ES2 0331411Inductive limit switch, closer, 10 m cable ES10 0331413Mechanical limit switch (Siemens), opener EMS 0331414Mechanical limit switch (Balluff), opener EMB 0331415
www.comoso.com
![Page 77: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/77.jpg)
w w w . s c h u n k . c o m238
technical data
Loads and load torques
Designation B 165-ZSSMax. travel speed [m/s] 5Repeat accuracy [mm] ± 0.08Max. acceleration [m/s²] 60Idle torque [Nm] 12.0DriveDrive element Toothed belt 75 AT 20Travel per revolution [mm] 440Maximum stroke [mm] 6920Max. total length [mm] 7700Moment of inertia [kgm²] 0.085WeightsBasic without travel [kg] 42.4Travel per 100 mm [kg] 3.5Slide plate 400 mm [kg] 11.9Slide plate 600 mm [kg] 17.9
Advantages of profiled rail guide
Linear Axes · toothed-belt Drive
B 165-ZSS
High load bearing capacity
Long lifetime
High precision
Load Dynamic Fx** [N] 10000 Fy
[N] 5000 Fz
[N] 15000 -Fz
[N] 8000Load torques Dynamic
Mx[Nm] 700
My[Nm] 1400 (2000)
Mz[Nm] 1100 (1500)
MAmax[Nm] 712.3
** Maximum value = Depending on speed Values in brackets relate to the long slide.
www.comoso.com
![Page 78: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/78.jpg)
w w w . s c h u n k . c o m 239
main views
Assembly connection Drive connection8 Feather key DIN 68859 Useful stroke
Mounting groove for T-nutsL Bolt pitch circle
Linear Axes · toothed-belt Drive
B 165-ZSS
Long slide
9 Useful stroke 8 Feather key
Drive journal connection dimensions
www.comoso.com
![Page 79: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/79.jpg)
w w w . s c h u n k . c o m240
Linear Axes · toothed-belt Drive
B 165-ZSS
mountingProfile ZSS
The profile can be secured either using T-nuts or mounting strips.
Designation Order designation ID no.T-nut NS6 0331409T-nut RM6 0331427Mounting strip BL3 0331402
motor flange schematic diagram
The table shows the relevant dimension C of the standard couplings. For dimension A refer to drive journal connection dimensions, for dimension B refer to corresponding motor dimension sheet, dimension L may differ in individual cases.Different drive solutions can be attached to our axes.SCHUNK can supply you with the right motor flange and coupling for your drive.
Because of the different thermal behavior of motors, we recommend that the drive solution is tested by the motor manufacturer.
L = A + B + C
Specific mass [kg/m] 25.13Planar dimension [mm²] 9308Planar moment of inertia ly [mm4] 25391136Planar moment of inertia lz [mm4] 31673479Load torque Wy [mm³] 264686Load torque Wz [mm³] 383919
More detailed information on pedestal bearings, connection shafts and bevel gears can be found in the "OPTIONS for System HSB" section of the catalog.
A Mounting strip T T-nut on base side
www.comoso.com
![Page 80: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/80.jpg)
w w w . s c h u n k . c o m 241
Linear Axes · toothed-belt Drive
B 165-ZSS
Lubrication connections
Limit switch selectionLimit switch position
T Standard lubrication connection
Standard connectionLubrication nipple M8x1
If the lubrication connection has a different seat, this must be defined in the order text.
Drive shafts
Depending on the axis application, the drive shaft seat may need to be defined in the order text. Particularly with axis combinations and mechanical synchronization, multiple drive shafts - some of them continuous shafts - are required.
T Limit switch standard position
Two EO2 switches are used as limit switches and an RS2 as the reference switch as standard.
The positions and dimensions of limit switches, switching lugs, and mounting components may vary depending on the application and the selected limit switches. Please contact us for assistance.
More detailed information on pedestal bearings, connection shafts and bevel gears can be found in the "OPTIONS for System HSB" section of the catalog.
Designation Order designation ID no.Inductive limit switch, opener, 2 m cable EO2 0331410Inductive limit switch, opener, 10 m cable EO10 0331412Inductive limit switch, closer, 2 m cable ES2 0331411Inductive limit switch, closer, 10 m cable ES10 0331413Mechanical limit switch (Siemens), opener EMS 0331414Mechanical limit switch (Balluff), opener EMB 0331415
www.comoso.com
![Page 81: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/81.jpg)
w w w . s c h u n k . c o m242
technical data
Loads and load torques
Designation B 180-ZSSMax. travel speed [m/s] 5Repeat accuracy [mm] ± 0.08Max. acceleration [m/s²] 60Idle torque [Nm] 8.0DriveDrive element Toothed belt 75 AT 10Travel per revolution [mm] 320Maximum stroke [mm] 5500Max. total length [mm] 6200Moment of inertia [kgm²] 0.056WeightsBasic without travel [kg] 37.7Travel per 100 mm [kg] 2.4Slide plate 380 mm [kg] 11.2Slide plate 600 mm [kg] 15.7
Advantages of profiled rail guide
Linear Axes · toothed-belt Drive
B 180-ZSS
High load bearing capacity
Long lifetime
High precision
Load Dynamic Fx** [N] 6000 Fy
[N] 6000 Fz
[N] 12000 -Fz
[N] 6000Load torques Dynamic
Mx[Nm] 1500
My[Nm] 3000 (4000)
Mz[Nm] 1500 (2000)
MAmax[Nm] 313.6
** Maximum value = Depending on speed Values in brackets relate to the long slide.
www.comoso.com
![Page 82: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/82.jpg)
w w w . s c h u n k . c o m 243
main views
Assembly connection Drive connection8 Feather key DIN 68859 Useful stroke
Mounting groove for T-nutsL Bolt pitch circle
Linear Axes · toothed-belt Drive
B 180-ZSS
Long slide
9 Useful stroke 8 Feather key
Drive journal connection dimensions
www.comoso.com
![Page 83: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/83.jpg)
w w w . s c h u n k . c o m244
Linear Axes · toothed-belt Drive
B 180-ZSS
mountingProfile ZSS
The profile can be secured either using T-nuts or mounting strips.
Designation Order designation ID no.T-nut NS3 0331406T-nut NS6 0331409T-nut RM2 0331425T-nut RM6 0331427Mounting strip BL3 0331402
motor flange schematic diagram
The table shows the relevant dimension C of the standard couplings. For dimension A refer to drive journal connection dimensions, for dimension B refer to corresponding motor dimension sheet, dimension L may differ in individual cases.Different drive solutions can be attached to our axes.SCHUNK can supply you with the right motor flange and coupling for your drive.
Because of the different thermal behavior of motors, we recommend that the drive solution is tested by the motor manufacturer.
L = A + B + C
Specific mass [kg/m] 15.49Planar dimension [mm²] 5736Planar moment of inertia ly [mm4] 9236448Planar moment of inertia lz [mm4] 23586987Load torque Wy [mm³] 134968Load torque Wz [mm³] 261545
More detailed information on pedestal bearings, connection shafts and bevel gears can be found in the "OPTIONS for System HSB" section of the catalog.
A Mounting strip T T-nut on base sideK Side T-nut
www.comoso.com
![Page 84: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/84.jpg)
w w w . s c h u n k . c o m 245
Linear Axes · toothed-belt Drive
B 180-ZSS
Lubrication connections
Limit switch selectionLimit switch position
T Standard lubrication connection
Standard connectionLubrication nipple M8x1
If the lubrication connection has a different seat, this must be defined in the order text.
Drive shafts
Depending on the axis application, the drive shaft seat may need to be defined in the order text. Particularly with axis combinations and mechanical synchronization, multiple drive shafts - some of them continuous shafts - are required.
T Limit switch standard position
Two EO2 switches are used as limit switches and an RS2 as the reference switch as standard.
The positions and dimensions of limit switches, switching lugs, and mounting components may vary depending on the application and the selected limit switches. Please contact us for assistance.
More detailed information on pedestal bearings, connection shafts and bevel gears can be found in the "OPTIONS for System HSB" section of the catalog.
Designation Order designation ID no.Inductive limit switch, opener, 2 m cable EO2 0331410Inductive limit switch, opener, 10 m cable EO10 0331412Inductive limit switch, closer, 2 m cable ES2 0331411Inductive limit switch, closer, 10 m cable ES10 0331413Mechanical limit switch (Siemens), opener EMS 0331414Mechanical limit switch (Balluff), opener EMB 0331415
www.comoso.com
![Page 85: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/85.jpg)
w w w . s c h u n k . c o m246
technical data
Loads and load torques
Designation B 180-ASSMax. travel speed [m/s] 5Repeat accuracy [mm] ± 0.08Max. acceleration [m/s²] 60Idle torque [Nm] 8.0DriveDrive element Toothed belt 75 AT 10Travel per revolution [mm] 320Maximum stroke [mm] 5470Max. total length [mm] 6200Moment of inertia [kgm²] 0.062WeightsBasic without travel [kg] 48.9Travel per 100 mm [kg] 2.8Slide drive 400 mm [kg] 25.6
Advantages of profiled rail guide
Linear Axes · toothed-belt Drive
B 180-ASS
High load bearing capacity
Long lifetime
High precision
Load Dynamic Fx** [N] 3500 Fy
[N] 6000 Fz
[N] 12000 -Fz
[N] 6000Load torques Dynamic
Mx[Nm] 1500
My[Nm] 3000
Mz[Nm] 1500
MAmax[Nm] 186.3
** Maximum value = Depending on speed Values in brackets relate to the long slide.
www.comoso.com
![Page 86: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/86.jpg)
w w w . s c h u n k . c o m 247
main views
Linear unit connection Assembly connection Drive connection8 Feather key DIN 68859 Useful stroke
Mounting groove for T-nutsL Bolt pitch circle
Linear Axes · toothed-belt Drive
B 180-ASS
8 Feather key
Drive journal connection dimensions
www.comoso.com
![Page 87: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/87.jpg)
w w w . s c h u n k . c o m248
Linear Axes · toothed-belt Drive
B 180-ASS
mountingProfile ASS
The profile can be secured either using T-nuts or mounting strips.
Designation Order designation ID no.T-nut NS3 0331406T-nut NS6 0331409T-nut RM2 0331425T-nut RM6 0331427Mounting strip BL3 0331402
motor flange schematic diagram
The table shows the relevant dimension C of the standard couplings. For dimension A refer to drive journal connection dimensions, for dimension B refer to corresponding motor dimension sheet, dimension L may differ in individual cases.Different drive solutions can be attached to our axes.SCHUNK can supply you with the right motor flange and coupling for your drive.
Because of the different thermal behavior of motors, we recommend that the drive solution is tested by the motor manufacturer.
L = A + B + C
Specific mass [kg/m] 15.49Planar dimension [mm²] 5736Planar moment of inertia ly [mm4] 9236448Planar moment of inertia lz [mm4] 23586987Load torque Wy [mm³] 134968Load torque Wz [mm³] 261545
More detailed information on pedestal bearings, connection shafts and bevel gears can be found in the "OPTIONS for System HSB" section of the catalog.
A Mounting strip T T-nut on base sideK Side T-nut
www.comoso.com
![Page 88: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/88.jpg)
w w w . s c h u n k . c o m 249
Linear Axes · toothed-belt Drive
B 180-ASS
Lubrication connections
Limit switch selectionLimit switch position
T Standard lubrication connection
Standard connectionLubrication nipple M8x1
If the lubrication connection has a different seat, this must be defined in the order text.
Drive shafts
Depending on the axis application, the drive shaft seat may need to be defined in the order text. Particularly with axis combinations and mechanical synchronization, multiple drive shafts - some of them continuous shafts - are required.
T Limit switch standard position
Two EO2 switches are used as limit switches and an RS2 as the reference switch as standard.
The positions and dimensions of limit switches, switching lugs, and mounting components may vary depending on the application and the selected limit switches. Please contact us for assistance.
More detailed information on pedestal bearings, connection shafts and bevel gears can be found in the "OPTIONS for System HSB" section of the catalog.
Designation Order designation ID no.Inductive limit switch, opener, 2 m cable EO2 0331410Inductive limit switch, opener, 10 m cable EO10 0331412Inductive limit switch, closer, 2 m cable ES2 0331411Inductive limit switch, closer, 10 m cable ES10 0331413Mechanical limit switch (Siemens), opener EMS 0331414Mechanical limit switch (Balluff), opener EMB 0331415
www.comoso.com
![Page 89: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/89.jpg)
w w w . s c h u n k . c o m250
technical data
Loads and load torques
Designation B 180C-ZRS B 180C-ZSSMax. travel speed [m/s] 8 5Repeat accuracy [mm] ± 0.08 ± 0.08Max. acceleration [m/s²] 60 60Idle torque [Nm] 8.0 8.0DriveDrive element Toothed belt 75 AT 10 75 AT 10Travel per revolution [mm] 320 320Maximum stroke [mm] 5500 5500Max. total length [mm] 6200 6200Moment of inertia [kgm²] 0.0425 0.0465WeightsBasic without travel [kg] 37.7 39.7Travel per 100 mm [kg] 1.9 2.6Slide plate 380 mm [kg] 13.5 14.65Slide plate 600 mm [kg] 14.6 15.75
Advantages of profiled rail guide
Linear Axes · toothed-belt Drive
B 180C-ZRS/-ZSS
High load bearing capacity
Long lifetime
High precision
Load ZRS dynamic ZSS dynamic Fx** [N] 6000 6000 Fy
[N] 6000 8000 Fz
[N] 10000 15000 -Fz
[N] 6000 8000Load torques ZRS dynamic ZSS dynamic
Mx[Nm] 1200 1800
My[Nm] 2000 (3000) 3600 (4800)
Mz[Nm] 1200 (1800) 1800 (2400)
MAmax[Nm] 313.6 313.6
** Maximum value = Depending on speed Values in brackets relate to the long slide.
High maximum moments due to optimum force transmission to the profile
Long stroke lengths can be achieved with no problems
Life-time lubricated rollers for easy maintenance use
Smooth, low-noise running
Advantages of roller guide
www.comoso.com
![Page 90: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/90.jpg)
w w w . s c h u n k . c o m 251
main views
Assembly connection Drive connection8 Feather key DIN 68859 Useful stroke
Mounting groove for T-nutsL Bolt pitch circle
Linear Axes · toothed-belt Drive
B 180C-ZRS/-ZSS
8 Feather key
Drive journal connection dimensionsLong slide
9 Useful stroke
www.comoso.com
![Page 91: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/91.jpg)
w w w . s c h u n k . c o m252
mounting
The profile can be secured either using T-nuts or mounting strips.
Designation Order designation ID no.T-nut NS3 0331406T-nut NS6 0331409T-nut RM2 0331425T-nut RM6 0331427Mounting strip BL3 0331402
Linear Axes · toothed-belt Drive
B 180C-ZRS/-ZSS
Profile ZRS/ZSS
motor flange schematic diagram
The table shows the relevant dimension C of the standard couplings. For dimension A refer to drive journal connection dimensions, for dimension B refer to corresponding motor dimension sheet, dimension L may differ in individual cases.Different drive solutions can be attached to our axes.SCHUNK can supply you with the right motor flange and coupling for your drive.
Because of the different thermal behavior of motors, we recommend that the drive solution is tested by the motor manufacturer.
L = A + B + C
Specific mass [kg/m] 15.49Planar dimension [mm²] 5736Planar moment of inertia ly [mm4] 9236448Planar moment of inertia lz [mm4] 23586987Load torque Wy [mm³] 134968Load torque Wz [mm³] 261545
More detailed information on pedestal bearings, connection shafts and bevel gears can be found in the "OPTIONS for System HSB" section of the catalog.
A Mounting strip T T-nut on base sideK Side T-nut
www.comoso.com
![Page 92: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/92.jpg)
w w w . s c h u n k . c o m 253
Linear Axes · toothed-belt Drive
B 180C-ZRS/-ZSS
Lubrication connections
Limit switch selectionLimit switch position
T Standard lubrication connection
Standard connectionLubrication nipple M8x1
If the lubrication connection has a different seat, this must be defined in the order text.
Drive shafts
Depending on the axis application, the drive shaft seat may need to be defined in the order text. Particularly with axis combinations and mechanical synchronization, multiple drive shafts - some of them continuous shafts - are required.
T Limit switch standard position
Two EO2 switches are used as limit switches and an RS2 as the reference switch as standard.
The positions and dimensions of limit switches, switching lugs, and mounting components may vary depending on the application and the selected limit switches. Please contact us for assistance.
More detailed information on pedestal bearings, connection shafts and bevel gears can be found in the "OPTIONS for System HSB" section of the catalog.
Designation Order designation ID no.Inductive limit switch, opener, 2 m cable EO2 0331410Inductive limit switch, opener, 10 m cable EO10 0331412Inductive limit switch, closer, 2 m cable ES2 0331411Inductive limit switch, closer, 10 m cable ES10 0331413Mechanical limit switch (Siemens), opener EMS 0331414Mechanical limit switch (Balluff), opener EMB 0331415
www.comoso.com
![Page 93: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/93.jpg)
w w w . s c h u n k . c o m254
technical data
Loads and load torques
Designation B 180C-ARS B 180C-ASSMax. travel speed [m/s] 8 5Repeat accuracy [mm] ± 0.08 ± 0.08Max. acceleration [m/s²] 60 60Idle torque [Nm] 8.0 8.0DriveDrive element Toothed belt 75 AT 10 75 AT 10Travel per revolution [mm] 320 320Maximum stroke [mm] 5470 5470Max. total length [mm] 6200 6200Moment of inertia [kgm²] 0.0715 0.0775WeightsBasic without travel [kg] 49.5 51.5Travel per 100 mm [kg] 2.8 3.6Slide drive 400 mm [kg] 26.2 27.35
Advantages of profiled rail guide
Linear Axes · toothed-belt Drive
B 180C-ARS/-ASS
High load bearing capacity
Long lifetime
High precision
Load ARS dynamic ASS dynamic Fx** [N] 3500 3500 Fy
[N] 6000 8000 Fz
[N] 10000 15000 -Fz
[N] 6000 8000Load torques ARS dynamic ASS dynamic
Mx[Nm] 1200 1800
My[Nm] 2000 (3000) 3600 (4800)
Mz[Nm] 1200 (1800) 1800 (2400)
MAmax[Nm] 186.3 186.3
** Maximum value = Depending on speed Values in brackets relate to the long slide.
High maximum moments due to optimum force transmission to the profile
Long stroke lengths can be achieved with no problems
Life-time lubricated rollers for easy maintenance use
Smooth, low-noise running
Advantages of roller guide
www.comoso.com
![Page 94: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/94.jpg)
w w w . s c h u n k . c o m 255
main views
Linear unit connection Assembly connection Drive connection8 Feather key DIN 68859 Useful stroke
Mounting groove for T-nutsL Bolt pitch circle
Linear Axes · toothed-belt Drive
B 180C-ARS/-ASS
8 Feather key
Drive journal connection dimensions
www.comoso.com
![Page 95: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/95.jpg)
w w w . s c h u n k . c o m256
mounting
The profile can be secured either using T-nuts or mounting strips.
Designation Order designation ID no.T-nut NS3 0331406T-nut NS6 0331409T-nut RM2 0331425T-nut RM6 0331427Mounting strip BL3 0331402
Linear Axes · toothed-belt Drive
B 180C-ARS/-ASS
Profile ARS/ASS
motor flange schematic diagram
The table shows the relevant dimension C of the standard couplings. For dimension A refer to drive journal connection dimensions, for dimension B refer to corresponding motor dimension sheet, dimension L may differ in individual cases.Different drive solutions can be attached to our axes.SCHUNK can supply you with the right motor flange and coupling for your drive.
Because of the different thermal behavior of motors, we recommend that the drive solution is tested by the motor manufacturer.
L = A + B + C
Specific mass [kg/m] 15.49Planar dimension [mm²] 5736Planar moment of inertia ly [mm4] 9236448Planar moment of inertia lz [mm4] 23586987Load torque Wy [mm³] 134968Load torque Wz [mm³] 261545
More detailed information on pedestal bearings, connection shafts and bevel gears can be found in the "OPTIONS for System HSB" section of the catalog.
A Mounting strip T T-nut on base sideK Side T-nut
www.comoso.com
![Page 96: Advantages of profiled rail guide Loads and load torques€¦ · Loads and load torques Designation B 40-ZSS Max. travel speed [m/s] 3 ... SCHUNK can supply you with the right motor](https://reader030.fdocuments.in/reader030/viewer/2022041009/5eb5cd7e4435c960002ef8c4/html5/thumbnails/96.jpg)
w w w . s c h u n k . c o m 257
Linear Axes · toothed-belt Drive
B 180C-ARS/-ASS
Lubrication connections
Limit switch selectionLimit switch position
T Standard lubrication connection
Standard connectionLubrication nipple M8x1
If the lubrication connection has a different seat, this must be defined in the order text.
Drive shafts
Depending on the axis application, the drive shaft seat may need to be defined in the order text. Particularly with axis combinations and mechanical synchronization, multiple drive shafts - some of them continuous shafts - are required.
T Limit switch standard position
Two EO2 switches are used as limit switches and an RS2 as the reference switch as standard.
The positions and dimensions of limit switches, switching lugs, and mounting components may vary depending on the application and the selected limit switches. Please contact us for assistance.
More detailed information on pedestal bearings, connection shafts and bevel gears can be found in the "OPTIONS for System HSB" section of the catalog.
Designation Order designation ID no.Inductive limit switch, opener, 2 m cable EO2 0331410Inductive limit switch, opener, 10 m cable EO10 0331412Inductive limit switch, closer, 2 m cable ES2 0331411Inductive limit switch, closer, 10 m cable ES10 0331413Mechanical limit switch (Siemens), opener EMS 0331414Mechanical limit switch (Balluff), opener EMB 0331415
www.comoso.com