Addendum #1 GA# 21-48 Delran Millbridge Addition

Delran Township Board of Education Millbridge Elementary School 2022 Classroom Addition

Addendum #1 December 3, 2021

Bid Package Clarification and Changes This Addendum dated December 3, 2021 for the Millbridge Elementary School 2022 Classroom Addition shall be included as part of the Contract Bid Documents. This Addendum shall supplement and clarify the current Contract Bid Documents.

THIS ADDENDUM CONSISTS OF (EIGHTEEN (18) PAGES). YOU MUST ACKNOWLEDGE RECEIPT OF THIS ENTIRE ADDENDUM BY SIGNING BELOW AND EMAILING BACK IMMEDIATELY TO [email protected]. THIS IS

MANDATORY! If this information is unclear, please call (856) 396-6200. If you are not bidding this project, please enter company name and write ANo Bid@ then email this page back. SIGNATURE COMPANY NAME 1. ADD the attached Finish Hardware specification section 08710 to project specification book. (16

Pages)

2. In Specification Section 04810 – Unit Masonry Assemblies, 2.6 BRICK, D. Building Brick: CLARIFY brick size to be standard 3 5/8” x3 5/8” x 7 5/8” long. Color to match existing brick veneer.

3. On Civil Drawing 4 of 9: DELETE Note #5 regarding construction entrance options. Contractor is to include the site access option directly from front parking lot along the side of the building (Option 2) in their project bid price.

4. On Drawing A6.0 - Finish Schedule: CHANGE flooring from VCT to CARPET in Rooms 001, 002, 002B, 003, 003B and 004. Drawing 1/A6.0 reflects correct flooring selections.

5. On Drawing S1.0 - Foundation notes #2: Under foundation plan shall refer to site elevation 43.10’.

6. On Drawing S3.0: Section 15/S3.0 footing width shall be 2’-0” wide per plan and footing schedule.

7. On Drawing S4.0: Detail 6/S4.0 title shall be column base plate detail. Dimension shall be A=1½”, D=3/4”. Section 7/S4.0 provide #4@24” foundation dowels. See section 13/S3.0 for similar condition.

8. On Drawing M3.0 - Air Device Schedule: Delete CD-2, SR/SG-1, RR/RG-1 and EG-3.

Addendum #1


1 of 18

Aliano Brothers General Contractors, Inc.

9. On Drawing E1.1 - Equipment Schedule: Add (4) Projectors. Proj-1, Proj-2, Proj-3 and Proj-4.

Provide dedicated 120V, 20 amp circuit per projector. Connect Projectors #1 and #2 to Panel P-ART-1. Connect Projectors #3 and #4 to Panel P-ART-2. For each projector, provide a 20-amp receptacle flush mounted on the underside of the ceiling grid.

10. On Drawing E1.1: Include costs in bid to locate the ATC panel anywhere within the project addition plus 75 feet.

11. On Drawing #E1.1: Card Reader outlet box at rear exit shall be weatherproof type box.

12. On Drawing E1.1: The Filled in Triangle Symbol with a “(D)” is a data outlet symbol. See below for correction to the symbol list.

13. On Drawing #E.1.1: The wall mounted fire alarm devices in each of the two bathrooms are Fire Alarm Strobe Only.

14. On Drawing E1.1: Symbol “S” in a hexagon with a subscript “SB” are Smartboard Speakers which are now Owner-provided speakers with Owner-provided wiring and are shown for reference only

15. On Drawing E2.1: Either of the two occupancy sensors in each of the four classrooms shall control all of the lights in the classroom

16. On Drawing E2.1 - Key Plan: The upper left note should read “Run all new data lines from the location shown to this patch panel”

17. The Type “C” downlight at the rear exit is a round light, not Square.

18. On Drawing E3.1 - Symbol List, Data Outlet Symbol: Add a “D” in Parenthesis to the top of the filled in triangle symbol.

19. On Drawing E3.1 – Symbol List: Add Fire Alarm Pull Station Symbol “F in a Square”. Double action pull station with vandal proof plastic cover.

20. On Drawing E3.1 – Symbol List: Smartboard Speaker “S” in a hexagon with a subscript “SB” are now Owner-provided speakers with Owner-provided wiring and are shown for reference only.

21. On Drawing #E3.1 – Symbol List: Add a symbol for a double duplex “Quad” receptacle. This

symbol is represented by two duplex receptacles, one on top of the other.

22. On Drawing #E3.2 – Single Line Diagram: The two new Panels are P-ART-1 and P-ART-2

Addendum #1


2 of 18

SECTION 08710 – FINISH HARDWARE – ADDED PER ADDENDUM #1

FINISH HARDWARE – ADDED PER ADDENDUM #1 08710-1

Part 1 - GENERAL

1.1 SUMMARY

A. Section Includes:1. Door Hardware, including electric hardware.2. Storefront and entrance door hardware.3. Overhead roll-up doors and Power operated overhead doors.4. Hold-open closers with fire-alarm interface.5. Wall or floor-mounted electromagnetic hold-open devices.6. Power supplies for electric hardware.7. Low energy door operators plus sensors and actuators.8. Remote button release hardware.9. Cabinet locks.10. Cylinders for doors fabricated with locking hardware.11. Wiring and riser diagrams for electric hardware.12. Key cabinets, key management software.

B. Specific Omissions: Hardware for the following is specified or indicated elsewhere.

1. Windows.2. Cabinets, including open wall shelving and locks.3. Signs, except where scheduled.4. Toilet accessories, including grab bars.5. Installation.6. Rough hardware.7. Folding partitions, except cylinders where detailed.8. Sliding aluminum doors, except cylinders where detailed.9. Access doors and panels, except cylinders where detailed.10. Corner Guards.11. Wrought Iron railing, gates and supports.12. Brass rail and drink rail supports.

1.2 REFERENCES:

A. Use date of standard in effect as of Bid date.B. American National Standards Institute – ANSI 156.18 – Materials and Finishes.C. ANSI A117.1 – Specifications for making buildings and facilities usable by physically

handicapped people.D. ADA – Americans with Disabilities Act of 1990E. BHMA – Builders Hardware Manufacturers AssociationF. DHI – Door and Hardware InstituteG. NFPA – National Fire Protection Association

1. NFPA 80 – Fire Doors and Windows

Addendum #1


3 of 18



2. NFPA 101 – Life Safety Code 3. NFPA 105 – Smoke and Draft Control Door Assemblies 4. NFPA 252 – Fire Tests of Door Assemblies

H. UL – Underwriters Laboratories

1. UL10C – Fire Tests of Door Assemblies (Positive Pressure) 2. UL 305 – Panic Hardware

I. WHI – Warnock Hersey Incorporated J. SDI – Steel Door Institute K. WDI – Wood Door Institute L. AWI – Architectural Woodwork Institute M. NAAM – National Association of Architectural Metal Manufacturers

1.3 SUBMITTALS & SUBSTITUTIONS

A. SUBMITTALS: Submit six copies of schedule per Division 1. Organize vertically formatted schedule into “Hardware Sets” with index of doors and headings, indicating complete designations of every item required for each door or opening. Include following information:

1. Type, style, function, size, quantity and finish of hardware items.

Use BHMA Finish codes per ANSI A156.18. 2. Name, part number and manufacturer of each item. 3. Fastenings and other pertinent information. 4. Location of hardware set coordinated with floor plans and door schedule. 5. Explanation of abbreviations, symbols, and codes contained in schedule. 6. Mounting locations for hardware. 7. Door and frame sizes, materials and degrees of swing. 8. List of manufacturers used and their nearest representative with address and

phone number. 9. Catalog cuts. 10. Manufacturer’s technical data and installation instructions for electronic

hardware. 11. Date of jobsite visit.

B. Bid and submit manufacturer’s updated/improved item if scheduled item is discontinued.

C. Make substitution requests in accordance with Division 1. Include product data and

indicate benefit to the Project. Furnish operating samples on request.

1. Items listed with no substitute manufacturers have been requested by Owner to meet existing standard.

Addendum #1


4 of 18



D. Furnish as-built/as-installed schedule with closeout documents, including keying schedule, wiring/riser diagrams, manufacturers’ installation, adjustment and maintenance information, and supplier’s final inspection report.

1.4 QUALITY ASSURANCE:

A. Qualifications:

1. Hardware supplier: direct factory contract supplier who employs a certified architectural hardware consultant (AHC), available at reasonable times during course Work for project hardware consultation to Owner, Architect and Contractor. (1) Responsible for detailing, scheduling and ordering of finish hardware.

B. Hardware: New, free of defects, blemishes and excessive play. Obtain each kind of

hardware (latch and locksets, exit devices, hinges and closers) from one manufacturer. C. Exit Doors: Operable from inside with single motion without the use of a key or special

knowledge or effort.

D. Fire-Rated Openings: In compliance with NFPA 80. Hardware UL10C/UBC-7-2 (positive pressure) compliant for given type/size opening and degree of label. Provide proper latching hardware, non-flaming door closers, approved-bearing hinges, plus resilient and required intumescent seals. Furnish openings complete.

1. Note: scheduled seals may exceed selected door manufacturer’s requirements.

See 2.6.E for clarification. E. Pre-Installation Meetings: Initiate and conduct with supplier, installer and related trades,

coordinate materials and techniques, and sequence complex hardware items and systems installation. Convene at least one week prior to commencement of related work.

1.5 DELIVERY, STORAGE AND HANDLING:

A. Delivery: coordinate delivery to appropriate locations (shop or field).

1. Permanent keys and cores: secured delivery direct to Owner’s representative.

B. Acceptance at Site: Items individually packaged in manufacturers’ original containers, complete with proper fasteners and related pieces. Clearly mark packages to indicate contents, locations in hardware schedule and door numbers.

C. Storage: Provide locked storage area for hardware, protect from moisture, sunlight, paint,

chemicals, etc.

Addendum #1


5 of 18



1.6 PROJECT CONDITIONS:

A. Where exact types of hardware specified are not adaptable to finished shape or size of members requiring hardware, provide suitable types having as nearly as practical as the same operation and quality as type specified, subject to Architect’s approval.

1.7 SEQUENCING AND COORDINATION:

A. Coordinate with concrete.

B. Reinforce walls.

C. Coordinate finish floor materials and floor-mounted hardware.

D. Conduit and raceways as needed for electrical, electronic and electro-pneumatic hardware items. Fire/life-safety system interfacing. Point-to-point wiring diagrams plus riser diagrams to related trades.

E. Furnish manufacturer templates to door and frame fabricators.

F. Use hardware consultant to check Shop Drawings for doors and entrances to confirm that

adequate provisions will be made for proper hardware installation.

1. Confirm that door manufacturers furnish necessary UBC-7-2 compliant seal packages.

1.8 WARRANTY:

A. Part of respective manufacturers’ regular terms of sale. Provide manufacturers’ warranties:

1. Closers: Thirty years mechanical, two years electrical. 2. Exit Devices: Three years. 3. Hinges: Life of Building. 4. Other Hardware: Two years.

1.9 COMMISSIONING:

A. Test door hardware operation with climate control system and stairwell pressurization system both at rest and while in full operation.

B. Test electrical, electronic and electro-pneumatic hardware systems for satisfactory

operation.

Addendum #1


6 of 18



C. Test hardware interfaced with fire/life-safety system for proper operation and release.

PART 2 - PRODUCTS 2.1 MATERIALS:

A. Provide hardware items required to complete the work in accordance with these specifications and manufacturers’ instructions.

1. Include items inadvertently omitted from this specification. Note these items in

submittal for review. 2. Where scheduled item is now obsolete, bid and furnish manufacturers updated

item at no additional cost to the project. 2.2 HANGING MEANS:

A. Conventional Hinges: Hinge open widths minimum, but, of sufficient throw to permit maximum door swing. Steel or stainless steel pins and concealed bearings.

1. Three hinges per leaf to 7 foot, 6 inch height. Add one for each additional 30

inches in height, or any fraction thereof. 2. Extra heavy weight hinges on doors over 3 foot, 5 inches in height. 3. Out swinging exterior doors: non-ferrous with non-removable (NRP) pins. 4. Non-ferrous material exteriors and at doors subject to corrosive atmospheric

conditions. 5. All hinges shall be non-removable tips – (NRP) 6. Provide shims and shimming instructions for proper door adjustment.

B. Continuous Hinges: Ives Aluminum Geared Continuous

1. UL 10C listed (90 minutes) 2. ANSI Certified-ANSI 156.25 Grade 2 3. Supports weights up to 450 lbs. 4’0” max. dr. width 4. Material to be extruded aluminum 6063-T6 5. Lengths- 83”,85”,95”, 120””- Custom Lengths available 6. All continuous geared hinges to be heavy duty-Amount of bearings varies by size

83”, 85”-32 bearings, 95”-36 bearings,120”-47 bearings a. Finishes Clear (CL) b. Manufacturer: Ives

2.3 LOCKSETS, LATCHSETS, DEADBOLTS:

A. General Requirements:

Addendum #1


7 of 18



1. Locks shall be cylindrical and mortise locks with trim selected to match building standard design, confirm trim before hardware submittal submission. Acceptable Manufacturers: Oaks Security and Schlage. (All permanent cores to be Medeco, and cylinders to be Oaks.) or approved equal.

2. Meet with Architect and Owner to finalize keying requirements and obtain keying instructions in writing. Keying schedule shall be coordinated with Owner’s Locksmith in compliance with specific requirements determined in consultation with Owner. Locks shall be masterkeyed to the existing Schlage key system. Contractor shall use owner’s locksmith to masterkey all cylinders and cut all keys, Contractor shall provide all permanent cores, and cut keys as required for the project and fullfilling the keying instructions as instructed by the Owner, procuring the keying from owner’s locksmith.

3. Provide temporary construction keying system during construction period. Permanent keys shall be furnished to Owner’s Representative prior to occupancy. Owner or Owner’s Security Agent will void operation of construction keys.

4. All temporary cores shall be returned to the supplier to avoid additional charges.

B. Cylinders: 1. Permanent cylinders shall fit Owner’s existing Medeco keyway- keyed to the

existing masterkey system and configured into sets or subsets, master keyed or great grand master keyed as directed by Owner.

2. Permanent keys and cylinder cores shall be engraved with industry standard keying nomenclature. These visual key control marks or codes shall not include actual key cuts. a. Key and cylinder identification stamping shall be approved by Architect and

Owner. Failure to properly comply with these requirements shall be cause for replacement of cylinders and keys involved at no additional cost to Owner.

b. Functions as listed in hardware sets. Key system – Medeco or approved equal.

2.4 EXIT DEVICES/PANIC HARDWARE

A. Exit Devices – Von Duprin 98 Series or approved equal. General features:

1. Independent lab-tested 1,000,000 cycles. 2. Push-through touch pad design. No exposed touch bar fasteners, no exposed

cavities when operated. Return stroke fluid dampeners and rubber bottoming dampeners, plus anti-rattle devices.

3. ¾” throw deadlocking latchbolts. 4. No exposed screws to show through glass doors. 5. Non-handed basic device design with center case interchangeable with all

functions, no extra parts required to effect change of function. 6. Releasable with 32 lb. maximum pressure under 250 lb. load to the door. 7. Where NL-OP designations are listed – confirm through presence of locking

cylinder if the door shall receive a cylinder preparation. If no cylinder is listed then do not prepare for cylinder, but include with material the trim ring, mounting cup, fasteners, and instructions for the NL-OP assembly.

Addendum #1


8 of 18



B. Specific features:

1. Non-Fire Rated Devices: cylinder dogging. 2. Lever Trim: Breakaway type, forged brass or bronze escutcheon min .130”

thickness, match lockset lever design. 3. Rod and latch guards with surface vertical rod devices. 4. Fire-Labeled Devices: UL label indicating “Fire Exit Hardware”. Vertical rod

devices less bottom rod (LBR) unless otherwise scheduled. 5. Devices shall have Security Indicator for Cylinder Dogging. 6. Delayed Egress Devices: Function achieved within single exit device component,

including latch, delayed locking device, request-to-exit switch, nuisance alarm, remote alarm, key switch, indicator lamp, relay, internal horn, door position input, external inhibit input plus fire alarm input. NFPA 101 “Special Locking Arrangement” compliant.

7. Electrically Operated Devices: Single manufacturer source for electric latch retraction devices, electrically controlled trim, power transfers, power supplies, monitoring switches and controls.

8. Removable Mullions: Removable with single turn of building key. Securely reinstalled without need for key. Furnish storage brackets for securely stowing the mullion away from the door when removed.

2.5 CLOSERS

A. Surface Closers: LCN 4111/4011 Series : To match existing;

1. Full rack-and-pinion type cylinder with removable non-ferrous cover and cast iron body. Double heat-treated pinion shaft, single piece forged piston, chrome-silicon steel spring.

2. ISO 2000 certified. Units stamped with date-of-manufacture code. 3. Independent lab-tested 8,000,000 cycles. 4. Thru-bolts at wood doors unless doors are provided with closer blocking. Non-

sized, non-handed, and adjustable. Place closer inside building, stairs, and rooms.

5. Plates, brackets and special templating when needed for interface with particular header, door and wall conditions and neighboring hardware.

6. Opening pressure: Exterior doors 8.5 lb., interior doors 5 lb., labeled fire doors 15 lb.

7. Separate adjusting valves for closing speed, latching speed and backcheck, fourth valve for delayed action where scheduled.

8. Extra-duty arms (EDA) at exterior doors scheduled with parallel arm units. 9. Exterior door closers: tested to 100 hours of ASTM B117 salt spray test, furnish

data on request. 10. Exterior doors do not require seasonal adjustments in temperatures from 120

degrees F to –30 degrees F, furnish data on request. 11. Non-flaming fluid will not fuel door or floor covering fires.

Addendum #1


9 of 18



12. Confirm mounting condition requirements for automatic door opener provide proper arm required, mounting plates, and frame reinforcement as required for proper installation.

13. Automatic Openers shall be LCN Senior Swing. 2.6 OTHER HARDWARE

A. Automatic Flush Bolts: Low operating force design, “LBR” type. B. Overhead Stops: Stainless steel (450 & 900 series). Non-plastic mechanisms and

finished metal end caps. Field-changeable hold-open, friction and stop-only functions.

C. Kick Plates: Four beveled edges, .050 inches minimum thickness, height and width as scheduled. Sheet-metal screws of bronze or stainless steel to match other hardware.

D. Magnetic Door Holders: Install magnetic door holders for maximum degree of opening,

coordinate with door closer template. Confirm voltage with security contractor before ordering.

E. Hinge-Guards – product specified is to establish a level of design criteria.

F. Door Stops: Provide stops to protect walls, casework or other hardware.

1. Unless otherwise noted in Hardware Sets, provide wall type with appropriate

fasteners. Where wall type cannot be used, provide overhead type.

G. Seals: Finished to match adjacent frame color. Resilient seal material: solid high-grade neoprene. UL label applied to seals on rated doors. Substitute products: certify that the products equal or exceed specified material’s thickness and durability. Proposed substitutions: submit for approval. Manufacturer: National Guard Products (NGP)

H. Thresholds: As scheduled and per details. Substitute products: certify that the products equal or exceed specified material’s thickness. Proposed substitutions: submit for approval. 1. Exteriors: Set in full bed of butyl-rubber or polyisobutylene mastic sealant

complying with requirements in Division 7 “Thermal and Moisture Protection”. Non-ferrous ¼ inch fasteners and lead expansion shield anchors, or Red-Head #SFS-1420 (or approved equivalent) Flat Head Sleeve Anchors (SS/FHSL).

2. Each specific door opening requires field measurement and confirmation of their individual sill condition. Product specified is for this reason. Size the thresholds per opening, the excessive width may not be required, so this is a base-line for budget purposes.

3. Sound control openings: Set in bed of mastic sealant.

Addendum #1


10 of 18



I. Fasteners: Generally, exposed screws to be Phillips or Robertson drive. Pinned TORX drive at high security areas. Flat head sleeve anchors (FHSL) may be slotted drive. Sheet metal and wood screws: full-thread. Sleeve nuts: full length to prevent door compression.

J. Silencers: Interior hollow metal frames, 3 for single doors, 4 for pairs of doors. Omit

where adhesive mounted seal occurs. Leave no unfilled/uncovered pre-punched silencer holes. Not required on doors receiving smoke gasketing.

2.7 FINISH:

A. Generally BHMA 626 Satin Chromium

1. Areas using BHMA 626 to have push-plates, pulls and protection plates of BHMA 630, Satin Stainless Steel, unless otherwise noted.

B. Door closers: factory powder coated to match other hardware, (BHMA 689) unless

otherwise noted. C. Aluminum items: match predominant adjacent material. Seals to coordinate with frame

color. 2.8 KEYING REQUIREMENTS:

A. Key System: Key to existing key system - Existing Manufacturer: Medeco X4 (Confirm)

B. All cylinders and cores to match existing key system requirements and be combinated per the Owner’s instructions.

C. Furnish all locks & cylinders with temporary construction cores, plastic temp. cores are not permitted.

D. Initiate and conduct meetings(s) with Owner’s Representative to determine the Schlage system keyway(s) and structure, Furnish Owner’s written approval of the system. 1. Furnish 12 construction keys. 2 Furnish 3 construction control keys. 3 Furnish 3 emergency keys 4 Furnish 6 keys per cylinder as key allowance. Final determination of how many of which keys are to be cut shall be determined during the masterkeying meeting, Allow 5 Master Keys per group and 3 Grand-Master keys

E. Cylinders/cores: keyed as directed by Owner by owner’s Locksmith. All removable cores to be factory stamped with keying . Provide bitting list to Owner.

F. Permanent keys: secured shipment direct from point of origination to Owner. G. Bitting List: Secured shipment direct from point of origination to Owners completion. H. Confirm the final key count in hardware submittal.

PART 3 - EXECUTION

Addendum #1


11 of 18



3.1 ACCEPTABLE INSTALLERS:

A. Factory trained, certified, and carries a factory-issued card certifying that person as a “Certified Installer”. Alternative: can demonstrate suitably equivalent competence and experience. Provide references upon request.

3.2 PREPARATION:

A. Ensure that walls and frames are square and plumb before hardware installation. B. Locate hardware per SDI-100 and applicable building, fire, life-safety, accessibility, and

security codes.

1. Notify Architect of any code conflicts before ordering material. 2. Where new hardware is to be installed near existing doors/hardware scheduled to

remain, match locations of existing hardware. C. Existing frames and doors scheduled to receive new hardware: carefully remove existing

hardware, tag and bag, and turn over to Owner.

1. Patch and fill wood frames and doors with solid wood stock or dowel material before cutting for new hardware. Do not reuse existing screw holes - - fill and re-pilot.

2. Metal doors/frames: Weld or fasten with screws: filler pieces in existing hardware cut-outs and mortises not scheduled for re-use by new hardware. Leave surfaces smooth - - no applied patches.

3.3 INSTALLATION

A. Install hardware per manufacturer’s instructions and recommendations. Do not install surface-mounted items until finishes have been completed on substrate. Set units level, plumb and true to line and location. Adjust and reinforce attachment substrate for proper installation and operation.

1. Gaskets: install jamb-applied gaskets before closers, overhead stops, rim strikes,

etc. Install sweeps across bottoms of doors before astragals, cope sweeps around bottom pivots, trim astragals to tops of sweeps.

2. When hardware is to be attached to existing metal surface and insufficient reinforcement exists, use RivNuts, NutSerts or similar anchoring device for screws.

B. Locate floor stops not more than 4 inches from the wall. C. Drill pilot holes for fasteners in wood doors and/or frames. D. Lubricate and adjust existing hardware scheduled to remain. Carefully remove and give

to Owner items not scheduled for reuse.

Addendum #1


12 of 18



3.4 FIELD QUALITY CONTROL.

A. Contractor shall employ and pay for services of a qualified independent Architectural Hardware Consultant (AHC) to perform inspections and to prepare inspection reports. Inspection Service:

B. After installation of door hardware is complete, the Awarded Hardware Distributor will inspect door hardware for proper application of finish hardware in compliance finish hardware schedule and keying schedule. In addition check hardware for adjustment and proper operation.

C. Contractor to provide written certification from a qualified AHC (Certified Architectural Hardware Consultant) that the hardware, cores and keying has been installed and tested in every door and is 100% complete for each phase or the total project which ever comes first

D. Prepare and submit, to Contractor, Architect, and Owner, a written report of inspection stating whether installed work complies with or deviates from requirements, including whether door hardware is properly installed and adjusted. Report shall be submitted within 3 days following site visits.

3.5 ADJUSTING

A. Initial Adjustment: 1. Adjust and check each operating item of door hardware and each door to ensure

proper operation or function of every unit. Replace units that cannot be adjusted to operate as intended. Adjust door control devices to compensate for final operation of heating and ventilating equipment and to comply with referenced accessibility requirements.

2. Adjust door closer sweep period so that from an open position of 70 degrees door will take at least 3 seconds to move to a point 3” from latch measured to leading edge of door.

B. Final Adjustment: 1. Return to Project during week prior to Substantial Completion and make final

check and adjustment of hardware items. 2. Adjust hardware so doors operate in perfect order. Test and adjust hardware for

quiet, smooth operation, free of sticking, binding, or rattling. Adjust closers for proper, smooth operation.

3. Adjust door control devices to compensate for final operation of heating and ventilating equipment.

C. Six Month Adjustment: 1. Approximately six months after Date of Substantial Completion, installer shall

perform following: a. Examine and readjust each item of door hardware as necessary to ensure

function of doors, door hardware. b. Consult with, and instruct, Owner’s personnel on recommended

maintenance procedures.

Addendum #1


13 of 18



c. Replace door hardware items that have deteriorated or failed due to faulty design, materials, or installation.

D. Twelve Month Adjustment: 1. Approximately twelve months after Date of Substantial Completion, installer shall

perform following: a. Examine and readjust each item of door hardware as necessary to ensure

function of doors, door hardware. b. Consult with, and instruct, Owner’s personnel on recommended

maintenance procedures. c. Replace door hardware items that have deteriorated or failed due to faulty

design, materials, or installation.

3.6 CLEANING

A. Exposed hardware shall be carefully cleaned by methods not injurious to finish, immediately preceding occupancy. Replace defective, damaged, or missing hardware.

B. Clean adjacent surfaces soiled by hardware installation.

C. Clean operating items as needed to restore proper function and finish.

3.7 DEMONSTRATION

A. Engage a factory-authorized service representative to train Owner’s maintenance personnel to adjust, operate, and maintain door hardware and door hardware finishes.

3.8 PROTECTION

A. Provide final protection and maintain conditions that ensure door hardware shall be without damage or deterioration at time of Substantial Completion.

B. Protect door hardware items from abuse, corrosion and other damage until Owner accepts Project as complete.

3.9 HARDWARE SCHEDULES TO FOLLOW: Please note that the Hardware Schedule has basis

of design manufacturers listed. Approved equal manufacturers will be considered in accordance with Specification Section 01300 – Submittals.

Addendum #1


14 of 18



HARDWARE GROUP NO. 01 For use on Door #(s): 000

Provide each PR door(s) with the following: QTY DESCRIPTION CATALOG NUMBER FINISH MFR 2 EA CONT. HINGE 224HD 628 IVE 2 EA FIRE EXIT HARDWARE 9847-EO-F 626 VON 2 EA SURFACE CLOSER 4111 EDA 689 LCN 2 EA KICK PLATE 8400 10" X 1" LDW B-CS 630 IVE 2 EA FIRE/LIFE WALL MAG SEM7850 AS REQ (12/24/120V

AC/DC TRI-VOLT) 689 LCN

1 EA GASKETING 488SBK PSA BK ZER 1 EA WEATHERSTRIPPING 8217SBK PSA BK ZER

Addendum #1


15 of 18



Hardware Group No. 02

For use on Door #(s): 000.1

Provide each PR door(s) with the following: QTY DESCRIPTION CATALOG NUMBER FINISH MFR 2 EA CONT. HINGE 224HD EPT 628 IVE 2 EA POWER TRANSFER EPT10 689 VON 1 EA REMOVABLE MULLION KR4954 689 VON 1 EA ELEC PANIC HARDWARE SD-RX-QEL-98-EO-SNB 24 VDC 626 VON 1 EA ELEC PANIC HARDWARE SD-RX-QEL-98-NL-OP-110MD-

SNB 24 VDC 626 VON

1 EA RIM CYLINDER 20-057 ICX 626 SCH 3 EA MORTISE CYLINDER 20-061 ICX 626 SCH 4 EA CORE AS REQUIRED 626 OAK 2 EA 90 DEG OFFSET PULL 8190EZHD 10" O 630-

316 IVE

2 EA SURFACE CLOSER 4111 SCUSH 689 LCN 2 EA MOUNTING PLATE 4110-18 689 LCN 2 EA CUSH SHOE SUPPORT 4110-30 689 LCN 2 EA BLADE STOP SPACER 4110-61 689 LCN 2 EA KICK PLATE 8400 10" X 1" LDW B-CS 630 IVE 1 EA GASKETING 188SBK PSA BK ZER 1 EA MEETING STILE 155AA AA ZER 1 EA MEETING STILE 55AA AA ZER 2 EA DOOR SWEEP 8197AA AA ZER 1 EA THRESHOLD 545A A ZER 1 EA MULLION SEAL 8780NBK PSA BK ZER 1 EA MULTITECH READER BY SECURITY INTEGRATOR BLK SCE 2 EA DOOR CONTACT BY SECURITY INTEGRATOR

"DOOR AND FRAME TO BE PREPPED FOR DOOR CONTACT."

BLK SCE

1 EA POWER SUPPLY PS904 900-2RS KL900 120/240 VAC

LGR SCE

Addendum #1


16 of 18




For use on Door #(s): 001 002 003 004

Provide each SGL door(s) with the following: QTY DESCRIPTION CATALOG NUMBER FINISH MFR 3 EA HINGE 5BB1HW 4.5 X 4.5 NRP 652 IVE 1 EA CLASSROOM SECURITY

LOCK 1CL-CS-2-C 626 OAK

2 EA CORE AS REQUIRED 626 OAK 1 EA SURFACE CLOSER 4111 EDA 689 LCN 1 EA KICK PLATE 8400 10" X 2" LDW B-CS 630 IVE 1 EA WALL STOP WS406/407CCV 626 IVE 1 EA GASKETING 488SBK PSA BK ZER


For use on Door #(s): 002A 003A

Provide each SGL door(s) with the following: QTY DESCRIPTION CATALOG NUMBER FINISH MFR 3 EA HINGE 5BB1 4.5 X 4.5 652 IVE 1 EA PRIVACY SECURITY LOCK 1CL-PR-C 626 OAK 1 EA SURFACE CLOSER 4011 689 LCN 1 EA KICK PLATE 8400 10" X 2" LDW B-CS 630 IVE 1 EA MOP PLATE 8400 4" X 1" LDW B-CS 630 IVE 1 EA WALL STOP WS406/407CCV 626 IVE 3 EA SILENCER SR64 GRY IVE


For use on Door #(s): 002B 003B

Provide each SGL door(s) with the following: QTY DESCRIPTION CATALOG NUMBER FINISH MFR 3 EA HINGE 5BB1 4.5 X 4.5 NRP 652 IVE 1 EA STOREROOM LOCK 1CL-ST-2-C 626 OAK 1 EA CORE AS REQUIRED 626 OAK 1 EA OH STOP 90S 630 GLY 3 EA SILENCER SR64 GRY IVE

Addendum #1


17 of 18



Hardware Group No. 05A

For use on Door #(s): 005

Provide each SGL door(s) with the following: QTY DESCRIPTION CATALOG NUMBER FINISH MFR 3 EA HINGE 5BB1 4.5 X 4.5 NRP 652 IVE 1 EA STOREROOM LOCK 1CL-ST-2-C 626 OAK 1 EA CORE AS REQUIRED 626 OAK 1 EA SURFACE CLOSER 4111 SCUSH 689 LCN 1 EA KICK PLATE 8400 10" X 2" LDW B-CS 630 IVE 1 EA GASKETING 488SBK PSA BK ZER

END OF SECTION

Addendum #1


18 of 18

Addendum #1 GA# 21-48 Delran Millbridge Addition

Documents

Transcript of Addendum #1 GA# 21-48 Delran Millbridge Addition