active - NeoBiotechnas.neobiotech.co.kr/170331/MU1_1 IS III active Catalog.pdfEB-II active SinusAll...

a c t i v e

New Products

2017. 03 E-Ver.01

ContentsIS-III active Benefits

IS-III active Features

IS-III active Line Up

Clinical Cases of IS-III active

Neo Surgical Kit

Opening the implant ampoule

IS-III active Drilling Protocol

P 06P 08P 11P 12P 14P 15P 16

A

B C D

E

F

G

0504

Connection01A.

B .

C.

Thicker Platform

Anti-screw Loosening

Abutment Compatibility

Design02D.

E .

F .

G.

Platform Microgroove

Magic Threads

0.9 Pitch

Cutting Edge

Surface03H.

I .

S.L.A. Surface

Cell Adhesion Ability

H

WHY IS-III active?

II

IS-III active implant is structured to maximize initial stability and facilitate faster osseointegration with its scientifically proven SLA surface and fixture body design.

0706

IS-III active Benefits

MicroGroove

0.9 Pitch

S.L.A.Surface

WideCutting Edge

Connection01Anti-screw Loosening ▶ Two Connection Points▶ Eliminate screw fracture

Abutment Compatibility ▶ Compatible with IS type▶ Conical 11° / Internal 2.5 Hex

Surface03Improved Surface ▶ Increased Surface Area▶ Facilitate faster osseointegration

Greater Cell Adhesion Ability ▶ More Cell adhesion▶ Facilitate faster osseointegration

Design02Platform Microgroove ▶ Enhanced Soft Tissue Sealing▶ Minimize bone loss

0.9 Pitch ▶ Reduced Bone Compression ▶ Optimal for Osseointegration

Wider Cutting Edge ▶ Improved Self-tapping Ability ▶ Maximize initial stability

Magic Threads ▶ Endure Vertical/Lateral Force ▶ Maximize initial stability

Predictable Implant Placement Successful Primary & Secondary Stability Faster Patient Recovery & Masticatory Function

Bene

fits

S.L.A. Surface

Wide Cutting Edge

before

0908

after

IS-III active FeaturesPlatform & Connection

Minimize Bone Loss

Microgroove design at the upper platform of the fixture enhances soft tissue sealing, thus prevents bone loss.

The new S.L.A. Surface with 40% greater surface area and 50% more cell ad-hesion promotes faster osseointegration.

Wider cutting edge and enlarged surface area enhances initial fixation and offers clinicians more stable implant placement.

Thicker connection through Increased platform thickness.

The coronal area of the fixture is also S.L.A. surface treated and takes a bevel border with open threaded design. These features facilitate osseointegration to crestal bone level, as well as minimize bone loss and maintain bone level.

0.175 0.375 Thickness increase

Platform microgroove Enhanced soft tissue barrier seal

Minimize bone loss through soft tissue integration and optimized soft tissue seal

Successful osseointegration to bone level

Minimize bone loss & main-tain bone level

Open threaded bevel coro-nal

Improved processing tech-nique of the S.L.A. Surface

Doubled cutting edge sur-face

Improved Self-tapping abil-ity while minimizing bone compression

Maximized initial fixation (AnyTime Loading)

40 percent increase in sur-face area

Reduced osseointegration time (50 percent increase in cell adhesion)

Maintains connection thickness over 3mm Increased strength of connection

Stronger Connection

Feat

ures

IS-III active Features0.9 Pitch

0.9

1110

Optimum Pitch for Osseointegration.

Increase in thread pitch to 0.9

Surgical Kit

Delayed Loading

Immediate Loading (AnyTime Loading)

Cortical Tap

More accessibility with improved cutting force of the surgical drills, now avail-able in two different lengths.

Clinicians decide the loading time by utilizing either the cortical drill or the cortical tap according to the patient’s bone density and oral conditions.

Cortical DrillUtilized for Delayed Load-ing by drilling the crestal cortical bone.

Utilized for Immediate (Any-Time) Loading by tapping the crestal cortical bone.

Dual drill length

Minimal bone compression (Prevent bone necrosis)

Provide optimal condition for osseointegration

Diameter

Length

Platform

Diameter PlatformLength (mm)

7.3 8.5 10.0 11.5 13.0

Ø3.5 Ø3.6

WIS3508AP WIS3510AP WIS3511AP WIS3513AP

Ø4.0 Ø4.1

WIS34007AP WIS34008AP WIS34010AP WIS34011AP WIS34013AP

Ø4.5 Ø4.5


Ø5.0 Ø5.0


Ø5.5 Ø5.5


Ø6.0 Ø6.0


IS-III active Line Up

Line

up.C

ases

1312

Clinical Cases of IS-III active

Case 1

Missing tooth IS-III active Placement

35~40Ncm of Insertion Torque Healing Abutment & Suture

1

3

2

4

Case 2

Missing tooth Drilling & Cortical Tapping

35~40Ncm of Insertion Torque Healing Abutment & Suture

1

3

2

4

Line

up.C

ases

1514

Neo Surgical Kit

Point Lindemann

Parallel Pin

Surgical Drill(Long / Short)

Connector

Direction Pin

Cortical Tap263.352mm

Drill Extention

Stopper

Cortical Drill

Hex Driver

Fixture Driver

Opening the implant ampoule

1

Remove the square-shaped ampoule from the blister.

2

Turn the lid to open the ampoule.

3

Remove the inner circular ampoule from the outer square-shaped ampoule.

4

Drop the inner ampoule onto the operating table.

5

Remove the safety cap (A cover screw can be found inside the cap).

6

Hold the sides of the ampoule when removing the cap. Must be cautious not to grip on the clip. (Opening of the clip will cause the fixture to fall into the ampoule.)

7

Hold the upper part of the clip and connect the fixture driver to the implant.

8

Simultaneously, push the lower part of the clip for clip opening and lift the implant out of the ampoule.

Neo

Surg

ical K

it

1716

IS-III active Drilling Protocol Drilling Speed & TorquePoint Lindemann, Initial Drill, Twist Drill : 1,200rpm / 35~45Ncm Cortical Tap : 50rpm / 50NcmCortical Drill : 1200rpm / 50Ncm (Conventional Loading case)

Point LindemannØ 2.3

Initial DrillØ 2.2

Twist DrillØ 3.0

Twist DrillØ 3.5

Cortical TapØ 4.0


Initial DrillØ 2.2

Twist DrillØ 3.0

Cortical TapØ 3.5

In soft(D4) bone or in condition of getting initial fixation at implant apex, Ø3.0 twist drill is the final drill

In soft(D4) bone, use Ø 2.2 initial drill as the final drill

IS-III active Fixture Ø4.0 X 10mm (D1/D2 bone)



Initial DrillØ 2.2

Twist DrillØ 3.0

Twist DrillØ 3.5

Twist DrillØ 4.0

Twist DrillØ 4.5

Cortical TapØ 5.0


Initial DrillØ 2.2

Twist DrillØ 3.0

Twist DrillØ 3.5

Twist DrillØ 4.0

Cortical TapØ 4.5





10mm

TipLength

D2

D1

10mm

TipLength

D2

D1

10mm

TipLength

D2

D1

10mm

TipLength

D2

D1

Drilli

ng Pr

otoc

ol

Sep.2016Jul. 2016May 2015Apr. 2015May 2014Dec. 2013Nov. 2013Oct. 2013

Jun. 2013Oct. 2012Jun. 2012Mar. 2012Oct. 2011Jun. 2011Oct. 2010Feb. 2010Jun. 2009Mar. 2009Nov. 2008Jul. 2008Mar. 2008Mar. 2008Sep. 2007Jun. 2007Feb. 2007Jul. 2000

IS-III activeEZ GBR SystemEncoded Healing abutmentCAMeleon csWorld Class 300Manufactured CAMeleonEB-II activeSinusAll KitPickCap Impression KitIT-II activeProsthetic Kit / Accessory KitNeoguide systemGBR KitIS-II active, QuicktightIS-II, S-mini & ACMCTi – memSR KitFR KitWide ImplantCMI IS implantSLA-KitSCA-KitObtain the patent of CMI ImplantMerged with “Osscare.Co.Ltd”CMI implant(External Type)Change of ManagementFoundation of “Neobiotech.Co,Ltd,.”

History of Neobiotech

Neobiotech Co.,Ltd10F, 36, Digitalro-27Gil, Guro-Gu, Seoul, Korea, 08381Tel 82-2-582-2885, Fax 82-2-582-2883 www.neobiotech.com / Made in Korea

active - NeoBiotechnas.neobiotech.co.kr/170331/MU1_1 IS III active Catalog.pdfEB-II active SinusAll...

Documents

Transcript of active - NeoBiotechnas.neobiotech.co.kr/170331/MU1_1 IS III active Catalog.pdfEB-II active SinusAll...