Material Evaluation: Self Damping Wire SD/ACSR Conductor ...
ACSR Tech Data 01 · PDF fileAluminium strip Aluminium wire Aluminium alloy wire ACSR...
Transcript of ACSR Tech Data 01 · PDF fileAluminium strip Aluminium wire Aluminium alloy wire ACSR...
Aluminium strip
Aluminium wire
Aluminium alloy wire
ACSR Aluminium Conductor Steel Reinforced
Other Aluminium products:
AAC (All aluminium conductor)
AAAC (All aluminium alloy conductor)
AACSR (All aluminium alloy conductor steel reinforced)
OPGW (Optic fiber protection overhead conductor)
Solid sector shaped aluminium conductor
www.m-tec.co.ca / [email protected] / +2716 450 8200
IEC
IEC
IEC
BS
BS EN
ASTM
CAN
Grade
g/cm3
Mpa
Conductivity Min.
Volume resistivity @ 20°C Ω.m
Coefficient of linier expansion per °C
Specific heat KJ/kg/K
Melt point °C
5 m
Min. % Nom. % 1.2 m
Al 99.650 99.700
Si - -
Fe 0.160 0.220
B 0.003 0.005
Other - -
Conductor continues maximum operating (°C)
Grease:
ASTM B231 (USA)
CAN/ CSA/C49 & C61089 (Canada) 1.22
0.60
890
7.154
Material properties
99.7 EC
658
Density / Specific gravity
Tensile strength (hard drawn)
Intermittent HV and
EHV voltages.
Up to 765kV an above
145
155
165
2
3
4
6
Thermal conductivity Air (W m-1 K-1)
Wind speed (m/sec)
Installation conditionsValue /
Variables
0.440
0.0264
16.04
Specifications:
IEC 61089
IEC 888
IEC 889 Velocity of Air (V) (m/hr.)
Ambient (°C)
Altitude (Katu Northern Cape)
Conductor surface absorbency (0.27-0.95)
Solar beam Intensity (W/m²) ID
Intensity of Solar sky radiation (W/m²) Id
The stated values are estimated and nominal values.
The installer should verify the actual conditions for the
specific location of installation.
30
75
BS 215 (British)
BS EN 50182 (British)
220°C
- 20°C to 80°C
Grease weight is calculated in
accordance with EN 50182 Annex B
Drop point IP 33 Min
Operating temperature
0.904
2.7
-
0.100
0.280
0.020
0.013
Chemical properties
Max. %
Last reviewed date: 16/01/2017.
# conductors SIL
per phase
Up to 132 & 220kV
Up to 440kV
100
130
1
Ground clearance (typical)
Aluminium
62.3
2.826x10-8
23x10-6
110-130
1.00058986Permittivity of air
Typical conductor configurations
The information contained within this document must not be copied, reprinted or reproduced in any form, either wholly or in part, without the written consent of M-TEC, The information is believed to be correct at the time of issue to the best of M-TEC’s
knowledge. M-TEC reserves the right to amend this specification without prior notification. This specification is not contractually valid unless specifically authorised by M-TEC. M-TEC shall not be liable for any damages whatsoever (including indirect,
incidental, special, punitive or consequential damages and loss of profits, opportunities or information) arising from or result from the use of or reliance on information contained in this document, and/or any inaccuracy or omission in such information
contained in this document.
ACSR Aluminium Conductor Steel Reinforced
A1/S1A
*Phase to phase clearance (typical)
www.m-tec.co.ca / [email protected] / +2716 450 8200
Aluminium conductor
Steel wire reinforcing
dia. area mass area mass dia. area mass
mm mm² kg/km mm² kg/km mm mm² kg/km
Nom. Nom. Nom. Nom. Nom. Nom. Nom. Nom.
Squirrel 1 / 2.11 2.11 3.5 27 6 / 2.11 21.0 57 6.33 24.48 84 (Z) RH ASTM
Gopher 1 / 2.36 2.36 4.4 34 6 / 2.36 26.2 71 7.08 30.62 105 (Z) RH ASTM
Weasel 1 / 2.59 2.59 5.3 41 6 / 2.59 31.6 85 7.77 36.88 127 (Z) RH ASTM
Fox 1 / 2.79 2.79 6.1 48 6 / 2.79 36.7 99 8.37 42.80 147 (Z) RH ASTM
Ferret 1 / 3.00 3.00 7.1 56 6 / 3.00 42.4 115 9.00 49.48 170 (Z) RH ASTM
Rabbit 1 / 3.35 3.35 8.8 69 6 / 3.35 52.9 143 10.05 61.70 212 (Z) RH ASTM
Mink 1 / 3.66 3.66 10.5 83 6 / 3.66 63.1 171 10.98 73.65 253 (Z) RH ASTM
Banana 1 / 3.75 3.75 11.0 87 6 / 3.75 66.3 179 11.25 77.31 266 (Z) RH ASTM
Quail 1 / 3.78 3.78 11.2 88 6 / 3.78 67.3 182 11.34 78.55 270 (Z) RH CAN
Beaver 1 / 3.99 3.99 12.5 98 6 / 3.99 75.0 203 11.97 87.53 301 (Z) RH BS EN
Racoon 1 / 4.09 4.09 13.1 103 6 / 4.09 78.8 213 12.27 91.97 316 (Z) RH BS EN
Otter 1 / 4.22 4.22 14.0 110 6 / 4.22 83.9 227 12.66 97.91 337 (Z) RH BS EN
Cat 1 / 4.50 4.50 15.9 125 6 / 4.50 95.4 258 13.50 111.33 383 (Z) RH BS EN
Hare 1 / 4.72 4.72 17.5 137 6 / 4.72 105.0 284 14.16 122.48 421 (Z) RH BS EN
Penguin 1 / 4.77 4.77 17.9 140 6 / 4.77 107.2 290 14.31 125.09 430 (Z) RH BS EN
Initial Final
*1200mm
(L)mH/km
Squirrel 50.2 80.4 8.02 0.70 1.374 1.646 1.276 0.011 1.694 130 2.87
Gopher 50.2 80.4 9.61 0.87 1.098 1.316 1.253 0.011 1.373 150 3.23
Weasel 50.2 80.4 11.45 1.05 0.912 1.092 1.234 0.011 1.159 170 3.56
Fox 50.2 80.4 13.10 1.22 0.786 0.941 1.219 0.011 1.016 190 3.86
Ferret 50.2 80.4 15.20 1.41 0.680 0.814 1.204 0.011 0.898 210 4.16
Rabbit 50.2 80.4 18.50 1.76 0.545 0.653 1.181 0.012 0.751 240 4.68
Mink 50.2 80.4 21.90 2.10 0.457 0.547 1.163 0.012 0.658 260 5.14
Banana 50.2 80.4 22.90 2.21 0.435 0.521 1.158 0.012 0.636 269 5.27
Quail 50.2 80.4 24.01 2.24 0.428 0.513 1.157 0.012 0.629 276 5.32
Beaver 50.2 80.4 25.90 2.50 0.384 0.460 1.146 0.012 0.584 290 5.63
Racoon 50.2 80.4 27.20 2.63 0.366 0.438 1.141 0.012 0.566 780 5.78
Otter 50.2 80.4 28.90 2.80 0.344 0.411 1.134 0.012 0.544 790 5.97
Cat 50.2 80.4 32.80 3.18 0.302 0.362 1.121 0.012 0.505 800 6.39
Hare 50.2 80.4 36.00 3.50 0.275 0.329 1.111 0.013 0.480 860 6.72
Penguin 50.2 80.4 37.87 3.57 0.269 0.322 1.109 0.013 0.475 920 6.80
Total Conductor
Ou
ter
laye
r
La
y d
ire
ctio
n
19.23
19.23
19.23
19.23
19.23
19.23
19.23
19.23
19.23
19.23
19.23
19.23
19.23
19.23
Steel core
Number/
Size
Co
ns
tru
cti
on
an
d d
ime
ns
ion
sP
hy
sic
al p
rop
ert
ies
Conductor
name
Conductor
name
19.23
Cu
rre
nt
ratin
g
dc
20°C
ac
75°C
Aluminium Outer layer(s)
* typical conductor centre spacing
Resistance
Ele
ctr
ica
l P
rop
ert
ies
Sp
ecific
atio
n
Sh
ort
cir
cu
it
ratin
g
kA.1sΩ/km
Number/
Size
Modulus of
Elasticity Coefficient
of linear
expansion
RTS
Grease
Nom.
(Case 2)kN/mm²
Nom. x10-6
/oC kN kg/km
Ind
ucta
nce
sin
gle
ph
ase
Imp
ed
an
ce
C
µF/km
Z
Ω/kmA
Ca
pa
cita
nce
The information contained within this document must not be copied, reprinted or reproduced in any form, either wholly or in part, without the written consent of M-TEC, The information is believed to be correct at the time of issue to the best of M-TEC’s
knowledge. M-TEC reserves the right to amend this specification without prior notification. This specification is not contractually valid unless specifically authorised by M-TEC. M-TEC shall not be liable for any damages whatsoever (including indirect,
incidental, special, punitive or consequential damages and loss of profits, opportunities or information) arising from or result from the use of or reliance on information contained in this document, and/or any inaccuracy or omission in such information
contained in this document.
ACSR (Aluminium Conductor Steel Reinforced)
(A1/S1A)
1 Steel centre wire + 6 Aluminium wires
www.m-tec.co.ca / [email protected] / +2716 450 8200
Aluminium conductor
Steel strand reinforcing
dia. area mass area mass dia. area mass
mm mm² kg/km mm² kg/km mm mm² kg/km
Nom. Nom. Nom. Nom. Nom. Nom. Nom. Nom.
Dog 7 / 1.57 4.79 13.6 106 6 / 4.72 105.0 284 11.01 118.54 390 (Z) RH ASTM
Leopard 7 / 1.75 5.34 16.8 132 6 / 5.28 131.4 355 12.31 148.21 487 (Z) RH ASTM
Hyena 7 / 1.97 6.02 21.3 168 7 / 4.39 106.0 286 10.75 127.29 454 (Z) RH ASTM
Initial Final
*1200mm
(L)mH/km
Dog 48.8 76.4 34.70 4.55 0.275 0.329 1.132 0.012 0.484 360 6.72
Leopard 48.8 76.4 42.20 5.68 0.219 0.263 1.154 0.012 0.448 410 7.57
Hyena 46.9 73.4 34.70 4.80 0.272 0.326 1.159 0.012 0.489 360 6.76
Aluminium Outer layer(s)
Cu
rre
nt
ratin
g
dc
20°C
* typical conductor centre spacing
Ph
ys
ica
l p
rop
ert
ies
Number/
Size
Co
ns
tru
cti
on
an
d
dim
en
sio
ns
Modulus of
Elasticity
7 Steel + 7 Aluminium
7 Steel + 6 Aluminium
Coefficient
of linear
expansion
RTS
Grease
Nom.
(Case 2)kN/mm²
Nom. A
Ele
ctr
ica
l P
rop
ert
ies
18.72
19.86
19.87
Total Conductor
Sp
ecific
atio
n
Ou
ter
laye
r
La
y d
ire
ctio
n
Resistance
Number/
Size
Steel core
ac
75°C
Ω/kmC
µF/km
Z
Ω/km
Ind
ucta
nce
sin
gle
ph
ase
Conductor
name Ca
pa
cita
nce
Imp
ed
an
ce
x10-6
/oC kN kg/km
The information contained within this document must not be copied, reprinted or reproduced in any form, either wholly or in part, without the written consent of M-TEC, The information is believed to be correct at the time of issue to the best of M-TEC’s
knowledge. M-TEC reserves the right to amend this specification without prior notification. This specification is not contractually valid unless specifically authorised by M-TEC. M-TEC shall not be liable for any damages whatsoever (including indirect,
incidental, special, punitive or consequential damages and loss of profits, opportunities or information) arising from or result from the use of or reliance on information contained in this document, and/or any inaccuracy or omission in such information
contained in this document.
Sh
ort
cir
cu
it
ratin
g
kA.1s
7 Steel + 6 Aluminium
7 Steel + 7 Aluminium
ACSR (Aluminium Conductor Steel Reinforced)
(A1/S1A)
7 Steel centre wire + 6, 7 Aluminium wires
7 Steel + 6 Aluminium
7 Steel + 7 Aluminium
Conductor
name
www.m-tec.co.ca / [email protected] / +2716 450 8200
Aluminium conductor
Steel wire reinforcing
dia. area mass area mass dia. area mass
mm mm² kg/km mm² kg/km mm mm² kg/km
Nom. Nom. Nom. Nom. Nom. Nom. Nom. Nom.
Dingo 1 / 3.35 10.23 8.8 69 18 / 3.35 158.7 429 16.75 167.47 498 (Z) RH ASTM
Chickadee 1 / 3.77 11.51 11.2 88 18 / 3.77 200.9 543 18.85 212.09 631 (Z) RH ASTM
Pelican 1 / 4.14 12.64 13.5 106 18 / 4.14 242.3 655 20.70 255.77 761 (Z) RH ASTM
Osprey 1 / 4.47 13.65 15.7 123 18 / 4.47 282.5 764 22.35 298.17 887 (Z) RH ASTM
Kingbird 1 / 4.78 14.60 17.9 141 18 / 4.78 323.0 873 23.90 340.96 1014 (Z) RH ASTM
Initial Final
*1200mm
(L)mH/km
Dingo 60.5 92.9 45.09 20.99 0.182 0.218 1.068 0.013 0.400 576 8.36
Chickadee 60.5 92.9 35.70 26.58 0.143 0.172 1.044 0.013 0.370 647 9.47
Pelican 60.5 92.9 53.80 32.05 0.119 0.143 1.025 0.014 0.352 646 10.45
Osprey 60.5 92.9 30.52 37.36 0.102 0.122 1.009 0.014 0.340 646 11.33
Kingbird 60.5 92.9 69.72 42.73 0.089 0.107 0.996 0.014 0.331 773 12.16
Aluminium Outer layer(s) Total Conductor
Number/
Size
Number/
Size
Steel core
Ou
ter
laye
r
La
y d
ire
ctio
n
Co
ns
tru
cti
on
an
d
dim
en
sio
ns
Conductor
name
kg/km
dc
20°C
Grease
Nom.
(Case 2)
Sp
ecific
atio
n
21.41
21.41
21.41
Ind
ucta
nce
sin
gle
ph
ase
Ca
pa
cita
nce
Imp
ed
an
ce
Cu
rre
nt
ratin
g
ac
75°C
Ω/kmC
µF/km
Z
Ω/kmA
kN/mm²
Modulus of
Elasticity Coefficient
of linear
expansion
RTS
* typical conductor centre spacing
Ph
ys
ica
l p
rop
ert
ies Conductor
name
Ele
ctr
ica
l P
rop
ert
ies
Nom. x10-6
/oC kN
21.41
21.41
The information contained within this document must not be copied, reprinted or reproduced in any form, either wholly or in part, without the written consent of M-TEC, The information is believed to be correct at the time of issue to the best of M-TEC’s
knowledge. M-TEC reserves the right to amend this specification without prior notification. This specification is not contractually valid unless specifically authorised by M-TEC. M-TEC shall not be liable for any damages whatsoever (including indirect,
incidental, special, punitive or consequential damages and loss of profits, opportunities or information) arising from or result from the use of or reliance on information contained in this document, and/or any inaccuracy or omission in such information
contained in this document.
kA.1s
Sh
ort
cir
cu
it
ratin
g
ACSR (Aluminium Conductor Steel Reinforced)
(A1/S1A)
1 Steel centre wire + 18 Aluminium wires
Resistance
www.m-tec.co.ca / [email protected] / +2716 450 8200
Aluminium conductor
Grease (if applicable)
dia. area mass area mass dia. area mass
mm mm² kg/km mm² kg/km mm mm² kg/km
Nom. Nom. Nom. Nom. Nom. Nom. Nom. Nom.
Petrel 7 / 2.34 7.02 30.1 238 12 / 2.34 51.6 139 11.70 81.71 377 (Z) RH ASTM
Skunk 7 / 2.59 7.77 36.9 291 12 / 2.59 63.2 171 12.95 100.10 462 (Z) RH ASTM
Leghorn 7 / 2.69 8.07 39.8 314 12 / 2.69 68.2 184 13.45 107.98 498 (Z) RH ASTM
Dotterel 7 / 3.08 9.24 52.2 412 12 / 3.08 89.4 242 15.40 141.56 653 (Z) RH ASTM
Oden 7 / 3.52 10.56 68.1 538 12 / 3.52 116.8 316 17.60 184.90 853 (Z) RH ASTM
Toucan 7 / 2.08 6.24 23.8 188 22 / 3.74 241.7 667 13.72 265.47 855 (Z) RH 10.586 ASTM
Flicker 7 / 2.39 7.17 31.4 248 24 / 3.58 241.6 653 14.33 272.99 901 (Z) RH 10.584 ASTM
Rook 7 / 2.76 8.28 41.9 331 24 / 4.14 323.1 873 16.56 364.95 1204 (Z) RH 10.577 ASTM
Dove 7 / 2.89 8.67 45.9 363 26 / 3.72 282.6 764 23.55 328.50 1126 (Z) RH 10.557 ASTM
Hawk 7 / 2.68 8.03 39.3 311 26 / 3.43 415.8 1,124 21.75 455.15 1435 (Z) RH 10.562 ASTM
Drake 7 / 3.45 10.36 65.6 518 26 / 4.44 402.9 1,089 28.13 468.51 1607 (Z) RH 10.543 ASTM
Initial Final
*1200mm
(L)mH/km
Petrel 46.1 70.8 57.52 8.60 0.522 0.682 1.141 0.012 0.771 150 4.63
Skunk 46.1 70.8 52.90 10.53 0.456 0.557 1.121 0.012 0.659 130 5.14
Leghorn 46.1 70.8 57.52 11.36 0.423 0.516 1.113 0.012 0.624 150 5.35
Dotterel 46.1 70.8 76.90 14.89 0.322 0.394 1.085 0.013 0.521 170 6.18
Oden 46.1 70.8 100.80 19.45 0.247 0.302 1.058 0.013 0.449 190 7.11
Toucan 58.8 90.4 68.90 40.14 0.119 0.146 1.106 0.012 0.377 452 10.55
Flicker 57.6 88.6 76.52 36.78 0.119 0.146 1.097 0.013 0.374 210 10.44
Rook 57.6 88.6 100.56 49.19 0.089 0.109 1.068 0.013 0.353 240 12.16
Dove 56.5 86.8 76.52 39.72 0.102 0.125 0.996 0.014 0.337 726 11.33
Hawk 58.9 90.6 57.52 18.47 0.069 0.085 1.012 0.014 0.329 610 13.89
Drake 56.5 86.8 57.52 30.98 0.072 0.087 0.960 0.015 0.314 830 13.66
19.85
15.61
15.61
15.61
15.61
19.84
19.29
19.29
20.52
Conductor
name
Ou
ter
laye
r
La
y d
ire
ctio
n
Resistance
7 Steel + 24 Aluminium
7 Steel + 26 Aluminium
Total Conductor
Number/
Size
Number/
Size
* typical conductor centre spacing
7 Steel + 22 Aluminium
7 Steel + 24 Aluminium
7 Steel + 26 Aluminium
20.44
Ph
ys
ica
l p
rop
ert
ies
Ele
ctr
ica
l P
rop
ert
ies
C
µF/km
Z
Ω/kmA
Ind
ucta
nce
sin
gle
ph
ase
Ca
pa
cita
nc
e
Imp
ed
an
ce
7 Steel + 12 Aluminium
ac
75°C
Ω/km
Cu
rre
nt
ratin
g
15.61
dc
20°C
Modulus of
Elasticity Coefficient
of linear
expansion
RTS
Grease
Nom.
(Case 2)kN/mm²
Nom. x10-6
/oC kN kg/km
7 Steel + 12 Aluminium
Steel core Aluminium Outer layer(s)
Steel strand reinforcing
7 Steel + 22 Aluminium
Co
ns
tru
cti
on
an
d d
ime
ns
ion
s
Conductor
name
Sp
ecific
atio
n
The information contained within this document must not be copied, reprinted or reproduced in any form, either wholly or in part, without the written consent of M-TEC, The information is believed to be correct at the time of issue to the best of M-TEC’s
knowledge. M-TEC reserves the right to amend this specification without prior notification. This specification is not contractually valid unless specifically authorised by M-TEC. M-TEC shall not be liable for any damages whatsoever (including indirect,
incidental, special, punitive or consequential damages and loss of profits, opportunities or information) arising from or result from the use of or reliance on information contained in this document, and/or any inaccuracy or omission in such information
contained in this document.
kA.1s
Sh
ort
cir
cu
it
ratin
g
ACSR (Aluminium Conductor Steel Reinforced)
(A1/S1A)
7 Steel centre wire + 12, 22, 24, 26, 30
Aluminium wires
7 Steel + 12 Aluminium
7 Steel + 22 Aluminium
7 Steel + 24 Aluminium
7 Steel + 26 Aluminium
www.m-tec.co.ca / [email protected] / +2716 450 8200
Aluminium conductor
Grease (if applicable)
dia. area mass area mass dia. area mass
mm mm² kg/km mm² kg/km mm mm² kg/km
Nom. Nom. Nom. Nom. Nom. Nom. Nom. Nom.
Tiger 7 / 2.36 7.21 30.6 240 30 / 2.36 131.2 355 16.52 161.85 595 (Z) RH BS EN
Wolf 7 / 2.59 7.91 36.9 290 30 / 2.59 158.1 427 18.13 194.94 717 (Z) RH BS EN
Lynx 7 / 2.79 8.52 42.8 336 30 / 2.79 183.4 496 19.53 226.20 832 (Z) RH CAN
Panther 7 / 3.00 9.16 49.5 389 30 / 3.00 212.1 573 21.00 261.54 962 (Z) RH BS
Bear 7 / 3.35 10.23 61.7 485 30 / 3.35 264.4 715 23.45 326.12 1199 (Z) RH BS EN
Lion 7 / 3.18 9.71 55.6 437 30 / 3.18 238.3 644 22.26 293.86 1081 (Z) RH BS EN
Goat 7 / 3.71 11.33 75.7 594 30 / 3.71 324.3 877 25.97 399.98 1471 (Z) RH BS EN
Deer 7 / 4.27 13.04 100.2 787 30 / 4.27 429.6 1,161 29.89 529.84 1949 (Z) RH BS EN
Elk 7 / 4.50 13.74 111.3 874 30 / 4.50 477.1 1,290 31.50 588.46 2164 (Z) RH BS EN
Tiger 54.3 83.4 57.87 15.98 0.220 0.268 1.512 0.009 0.546 260 7.57
Wolf 54.3 83.4 68.91 19.25 0.182 0.223 1.493 0.009 0.519 269 8.34
Lynx 54.3 83.4 79.30 22.34 0.157 0.192 1.478 0.009 0.503 276 9.03
Panther 54.3 83.4 90.80 25.83 0.136 0.166 1.463 0.009 0.489 290 9.74
Bear 54.3 83.4 109.38 32.21 0.109 0.133 1.441 0.009 0.472 780 10.94
Lion 54.3 83.4 98.98 29.02 0.121 0.148 1.451 0.009 0.479 790 10.36
Goat 54.3 83.4 133.28 39.50 0.089 0.109 1.420 0.009 0.459 800 12.19
Deer 54.3 83.4 175.42 52.33 0.067 0.082 1.391 0.009 0.445 860 14.13
Elk 54.3 83.4 198.80 58.12 0.060 0.074 1.381 0.010 0.440 920 14.93
7 Steel + 30 Aluminium
Co
ns
tru
cti
on
an
d d
ime
ns
ion
sP
hy
sic
al p
rop
ert
ies
kNx10-6
/oCNom.
18.31
18.31
18.31
kN/mm²
A
* typical conductor centre spacing
kg/km
18.31
18.31
Coefficient
of linear
expansion
RTS
18.31
18.31
Conductor
name
Grease
Nom.
(Case 2)
Ele
ctr
ica
l P
rop
ert
ies
Resistance
7 Steel + 30 Aluminium
Ω/kmC
µF/km
Z
Ω/km
18.31
18.31
Conductor
name
Steel strand reinforcing
Steel core Aluminium Outer layer(s)
Number/
Size
Number/
Size
L
mH/km
Cu
rre
nt
ratin
g
dc
20°C
ac
75°C
Total Conductor
Ou
ter
laye
r
La
y d
ire
ctio
n
Sp
ecific
atio
n
Initial Final
Modulus of
Elasticity
Single phase
Ind
ucta
nce
Ca
pa
cita
nce
Imp
ed
an
ce
The information contained within this document must not be copied, reprinted or reproduced in any form, either wholly or in part, without the written consent of M-TEC, The information is believed to be correct at the time of issue to the best of M-TEC’s
knowledge. M-TEC reserves the right to amend this specification without prior notification. This specification is not contractually valid unless specifically authorised by M-TEC. M-TEC shall not be liable for any damages whatsoever (including indirect,
incidental, special, punitive or consequential damages and loss of profits, opportunities or information) arising from or result from the use of or reliance on information contained in this document, and/or any inaccuracy or omission in such information
contained in this document.
kA.1s
Sh
ort
cir
cu
it
ra
tin
g
7 Steel + 30 Aluminium
ACSR (Aluminium Conductor Steel Reinforced)
(A1/S1A)
7 Steel centre wire + 30 Aluminium wires
www.m-tec.co.ca / [email protected] / +2716 450 8200
Aluminium conductor
Grease (if applicable)
dia. area mass area mass dia. area mass
mm mm² kg/km mm² kg/km mm mm² kg/km
Nom. Nom. Nom. Nom. Nom. Nom. Nom. Nom.
Zambezi 7 / 2.32 7.09 29.6 235 42 / 4.14 565.4 1,528 31.80 594.97 1764 (Z) RH BS EN
Tern 7 / 2.25 6.87 27.8 221 45 / 3.38 403.8 1,113 27.03 431.60 1335 (Z) RH ASTM
Ruddy 7 / 2.40 7.33 31.7 249 45 / 3.59 455.5 1,256 28.74 487.17 1505 (Z) RH ASTM
Rail 7 / 2.47 7.54 33.5 263 45 / 3.70 483.8 1,334 29.61 517.39 1597 (Z) RH ASTM
Bluejay 7 / 2.66 8.12 38.9 306 45 / 4.00 565.5 1,559 31.98 604.39 1865 (Z) RH ASTM
Bunting 7 / 2.76 8.43 41.9 329 45 / 4.12 599.9 1,654 33.00 641.80 1983 (Z) RH ASTM
Bersfort 7 / 3.32 10.14 60.6 476 48 / 4.27 687.4 1,895 35.58 747.96 2371 (Z) RH CAN
Peaceriver 7 / 2.25 6.87 27.8 219 48 / 2.90 317.0 874 24.15 344.88 1093 (Z) RH CAN
Initial Final
*1200mm
kN kg/km (L)mH/km
Zambezi 47.7 73.2 98.3 73 8.507 0.062 0.935 0.015 0.300 610 11.98
Tern 47.7 73.2 98.3 49 0.071 0.087 0.968 0.015 0.316 830 13.81
Ruddy 48.9 75.8 108.5 55 0.063 0.077 0.955 0.015 0.310 955 14.71
Rail 48.9 75.8 115.1 58 0.060 0.073 0.949 0.015 0.307 920 15.19
Bluejay 49.0 75.8 135.0 68 0.051 0.062 0.934 0.015 0.300 1,000 16.49
Bunting 49.0 75.8 142.2 72 0.048 0.059 0.927 0.016 0.297 1,100 17.01
Bersfort 48.4 74.9 180.0 77 0.042 0.051 0.912 0.016 0.291 1,132 18.27
Peaceriver 48.4 74.9 88.0 36 0.091 0.111 0.991 0.014 0.331 1,002 12.16
21.09
21.07
7 Steel + 42 Aluminium
7 Steel + 45 Aluminium
7 Steel + 48 Aluminium
RTS
Grease
Nom.
(Case 2)
Ph
ys
ica
l p
rop
ert
ies
Conductor
name
Nom. x10-6
/oC
7 Steel + 42 Aluminium
7 Steel + 45 Aluminium
7 Steel + 48 Aluminium
Conductor
name
Steel core
Ou
ter
laye
r
La
y d
ire
ctio
n
Sh
ort
cir
cu
it
ratin
g
kA.1s
Co
ns
tru
cti
on
an
d d
ime
ns
ion
s
Steel strand reinforcing
Aluminium Outer layer(s) Total Conductor
Sp
ecific
atio
n
Number/
Size
Number/
Size
7 Steel + 42 Aluminium
7 Steel + 45 Aluminium
7 Steel + 48 Aluminium
Modulus of
ElasticityIn
du
cta
nce
sin
gle
ph
ase
Ca
pa
cita
nce
Imp
ed
an
ce
Cu
rre
nt
ratin
g
dc
20°C
ac
75°C
Ω/kmC
µF/km
Z
Ω/km
21.08
21.49
Ele
ctr
ica
l P
rop
ert
ies
Resistance
Coefficient
of linear
expansion
kN/mm²
The information contained within this document must not be copied, reprinted or reproduced in any form, either wholly or in part, without the written consent of M-TEC, The information is believed to be correct at the time of issue to the best of M-TEC’s
knowledge. M-TEC reserves the right to amend this specification without prior notification. This specification is not contractually valid unless specifically authorised by M-TEC. M-TEC shall not be liable for any damages whatsoever (including indirect,
incidental, special, punitive or consequential damages and loss of profits, opportunities or information) arising from or result from the use of or reliance on information contained in this document, and/or any inaccuracy or omission in such information
contained in this document.
* typical conductor centre spacing
ACSR (Aluminium Conductor Steel Reinforced)
(A1/S1A)
7 Steel centre wire + 42, 45, 48 Aluminium wires
A
20.66
20.67
21.09
21.07
www.m-tec.co.ca / [email protected] / +2716 450 8200
Aluminium conductor
Grease (if applicable)
dia. area mass area mass dia. area mass
mm mm² kg/km mm² kg/km mm mm² kg/km
Nom. Nom. Nom. Nom. Nom. Nom. Nom. Nom.
Crow 7 / 2.92 8.92 46.9 368 54 / 4.27 773.3 2,090 34.38 820.16 2458 (Z) RH ASTM
Antelope 7 / 2.97 9.07 48.5 381 54 / 2.97 374.1 1,011 26.73 422.60 1392 (Z) RH BS
Bison 7 / 3.00 9.16 49.5 389 54 / 3.00 381.7 1,032 27.00 431.18 1420 (Z) RH BS
Zebra 7 / 3.18 9.71 55.6 437 54 / 3.18 428.9 1,159 28.62 484.48 1596 (Z) RH BS EN
Camel 7 / 3.35 10.23 61.7 485 54 / 3.35 476.0 1,287 30.15 537.66 1771 (Z) RH BS EN
Moose 7 / 3.53 10.78 68.5 538 54 / 3.53 528.5 1,428 31.77 596.99 1967 (Z) RH BS EN
Condor 7 / 3.08 9.41 52.2 410 54 / 3.08 402.3 1,088 27.72 454.49 1497 (Z) RH BS EN
Cardinal 7 / 3.38 10.32 62.8 493 54 / 3.38 484.5 1,310 30.42 547.33 1803 (Z) RH BS EN
Initial Final
*1200mm
kN kg/km (L)mH/km
Crow 46.7 73.2 113.0 77 0.037 0.046 0.918 0.016 0.292 780 19.24
Antelope 46.7 73.2 117.0 37 0.077 0.094 0.969 0.015 0.319 790 13.14
Bison 46.7 73.2 119.0 38 0.076 0.092 0.967 0.015 0.317 800 13.28
Zebra 46.7 73.2 133.0 43 0.067 0.082 0.955 0.015 0.311 860 14.12
Camel 46.7 73.2 147.0 48 0.061 0.074 0.944 0.015 0.306 920 14.91
Moose 46.7 73.2 162.0 53 0.055 0.067 0.934 0.015 0.301 980 15.75
Condor 46.7 73.2 127.9 40 0.072 0.088 0.961 0.015 0.315 889 13.65
Cardinal 46.7 73.2 149.2 49 0.059 0.073 0.942 0.015 0.305 1,022 15.05
Ph
ys
ica
l p
rop
ert
ies
Conductor
name
Ele
ctr
ica
l P
rop
ert
ies
Resistance
Nom.
19.85
7 Steel + 54 Aluminium
19.85
x10-6
/oC
19.85
21.29
19.85
19.85
19.85
19.85
7 Steel + 54 Aluminium
RTS
Grease
Nom.
(Case 2)
kN/mm²
Modulus of
Elasticity Coefficient
of linear
expansion
7 Steel + 54 Aluminium
Co
ns
tru
cti
on
an
d
dim
en
sio
ns
Conductor
name
Steel core Aluminium Outer layer(s) Total Conductor
Number/
Size
Number/
Size
Sp
ecific
atio
n
Ou
ter
laye
r
La
y d
ire
ctio
n
Steel strand reinforcing
ac
75°C
Ω/kmC
µF/km
Z
Ω/kmA
Sh
ort
cir
cu
it
ratin
g
kA.1sIn
du
cta
nce
sin
gle
ph
ase
Ca
pa
cita
nce
Imp
ed
an
ce
Cu
rre
nt
ratin
g
dc
20°C
The information contained within this document must not be copied, reprinted or reproduced in any form, either wholly or in part, without the written consent of M-TEC, The information is believed to be correct at the time of issue to the best of M-TEC’s
knowledge. M-TEC reserves the right to amend this specification without prior notification. This specification is not contractually valid unless specifically authorised by M-TEC. M-TEC shall not be liable for any damages whatsoever (including indirect,
incidental, special, punitive or consequential damages and loss of profits, opportunities or information) arising from or result from the use of or reliance on information contained in this document, and/or any inaccuracy or omission in such information
contained in this document.
* typical conductor centre spacing
ACSR (Aluminium Conductor Steel Reinforced)
(A1/S1A)
7 Steel centre wire + 54 Aluminium wires
www.m-tec.co.ca / [email protected] / +2716 450 8200