ACC Climate Control, Inc. 23022 Series Evaporator Features: One dynamically balanced twin shaft...

ACC Climate Control, Inc. 23022 Series Evaporator

Features:• One dynamically balanced twin shaft blower assembly with long life 12 volt DC permanent magnet motors with full ball bearings and extended life brushes.• Orifice tube/accumulator in lieu of TXV used in conjunction with highly efficient crosshatch copper tube and an aluminum fin coil for maximum capacity output and durability.• Standard manual controls or fully automatic. Electronic controls are pre-wired relays and circuit breakers. Relay board with electrical diagnostic LEDs can be mounted at evaporator or control panel at driver. • Utilizes our uniquely designed mounting system, eliminating the need to drill holes through the roof.• Available with heat.

Specifications:• 40,000 BTU/hr cooling capacity• 495 cfm• Amp Draw High – 19 amps• 3 speed fans• 12 or 24 volts• Dimensions: 28.75”W x 9”H x 19.375”D• Weight – 52 lbs

Key Components:• Coil: 11471511A• Blower Assembly: 26060040A• Orifice Tube:08800502A• Front/Rear Mount Cover: 09976091A• Side Mount Cover: 09976098A

In the interests of continuous improvement, specifications are subject to change without notice.


Features:• Two dynamically balanced twin shaft blower assemblies with long life 12 volt DC permanent magnet motors with full ball bearings and extended life brushes.• Orifice tube/accumulator in lieu of TXV used in conjunction with highly efficient crosshatch copper tube and an aluminum fin coil for maximum capacity output and durability.• Standard manual controls or fully automatic. Electronic controls are pre-wired relays and circuit breakers. Relay board with electrical diagnostic LEDs can be mounted at evaporator or control panel at driver. • Utilizes our uniquely designed mounting system, eliminating the need to drill holes through the roof.• Available with heat.

Specifications:• 53,000 BTU/hr cooling capacity• 1200 cfm• Amp Draw High – 30 amps• 3 speed fans• 12 or 24 volts• Dimensions: 42”W x 10”H x 19.5”D• Weight – 60 lbs

Key Components:• Coil: 11471508A• Blower Assembly: 26060036A• Orifice Tube:08800502A• Front/Rear Mount Cover: 09976094A• Side Mount Cover: 09976097A


Features:Larger 67,000 BTU Capacity for those critical midsize applications.Two dynamically balanced twin shaft blower assemblies with long life 12 volt DC permanent magnet motors with full ball bearings and extended life brushes. Orifice tube/accumulator in lieu of TXV used in conjunction with highly efficient crosshatch copper tube and an aluminum fin coil for maximum capacity output and durability. Standard manual controls or fully automatic. Electronic controls are pre-wired relays and circuit breakers. Relay board with electrical diagnostic LEDs can be mounted at evaporator or control panel at driver. Utilizes our uniquely designed mounting system, eliminating the need to drill holes through the roof. Available with heat.

Specifications: 67,000 BTU/hr cooling capacity 1400 cfm Amp Draw High – 30 amps 3 speed fans 12 or 24 volts Dimensions: 42”W x 10”H x 19.5”DWeight – 60 lbs

Condenser Options:25031 78,000 BTU Skirt Condenser25045 78,000 BTU Rooftop Condenser


Features:• This heavy-duty, high capacity ceiling mount unit provides cooling for a variety of vehicles with large passenger compartments. It easily can substitute for two single blower or single and double AC units. • Due to the unit consisting of two independent evaporators, it can be installed as A) one stand alone or tie in system, or B) two independent systems, with two you will get a 30 amp draw plus a 15 amp draw. The latter option gives the option of turning on either a single system or both systems.• Three dynamically balanced twin shaft blower assemblies that utilize long life 12 volt DC permanent magnet motors with full ball bearings and extended life brushes. • An orifice tube used in conjunction with highly efficient enhanced copper tube and an aluminum fin coil for maximum capacity.• Standard manual controls or fully automatic. Electronic controls are pre-wired relays and circuit breakers mounted to the evaporator. Utilizes our uniquely designed mounting system that eliminates the need to drill through the roof. Available with heat. Specifications:• 86,000 BTU/hr cooling capacity• 105,000 BTU/hr heating capacity• 1800 cfm• Amp Draw High – 30 plus 15• 3 speed fans• 12 volt• Dimensions: 42”W x 10”H x 19.5”D• Weight – 95 lbs

Key Components:• Coil: 11471508A• Blower Assembly: 26060040A• Orifice Tube:08800502A• Rear Mount Cover: 09976119A


Features: This ceiling mount unit provides cooling to any bus, van, or other vehicle’s passenger compartment. The low profile unit is specifically designed for vehicles with low head clearance. An orifice tube used in conjunction with highly efficient enhanced copper tube and an aluminum fin coil for maximum capacity output and durability. Standard manual controls or fully automatic. Electronic controls are pre-wired with relays and circuit breakers mounted to the evaporator. durable ABS formed drain pan and outlet plenum with fully adjustable louver vents. Utilizes our uniquely designed mounting system that eliminates the need to drill through the roof. Specifications: 30,000 BTU/hr cooling capacity 35,000 BTU/hr heating capacity 600 cfm Amp Draw High – 20.6 3 speed fans 12 volt Dimensions: 35 3/4”W x 6 1/4”H x 14 1/16”D Weight – 38 lbs

Key Components: Coil: 11471634A Blower Assembly: 26060046A Orifice Tube: 08800505A Rear Mount Cover: 09976117A


Features: Low profile design for more headroom clearance. Two dynamically balanced twin shaft blower assemblies with long life 12 volt DC permanent magnet motors with full ball bearings and extended life brushes. Orifice tube/accumulator in lieu of TXV used in conjunction with highly efficient crosshatch copper tube and an aluminum fin coil for maximum capacity output and durability. Standard manual controls or fully automatic. Electronic controls are pre-wired relays and circuit breakers. Relay board with electrical diagnostic LEDs can be mounted at evaporator or control panel at driver. Utilizes our uniquely designed mounting system, eliminating the need to drill holes through the roof. Specifications: 53,000 BTU/hr cooling capacity 1200 cfm Amp Draw High – 30 amps 3 speed fans 12 or 24 volts Dimensions: 41.7”W x 7.0”H x 21.04”D

Weight – 56 lbs



Features: Low profile design for more headroom clearance. One dynamically balanced twin shaft blower assemblies with long life 12 volt DC permanent magnet motors with full ball bearings and extended life brushes. Orifice tube/accumulator in lieu of TXV used in conjunction with highly efficient crosshatch copper tube and an aluminum fin coil for maximum capacity output and durability. Standard manual controls or fully automatic. Electronic controls are pre-wired relays and circuit breakers. Relay board with electrical diagnostic LEDs can be mounted at evaporator or control panel at driver. Utilizes our uniquely designed mounting system, eliminating the need to drill holes through the roof. Specifications: 40,000 BTU/hr cooling capacity 600 cfm Amp Draw High – 15 amps 3 speed fans 12 volts Dimensions: 41.7”W x 7.0”H x 21.04”D

Weight – 52 lbs



Features:• Two dynamically balanced twin shaft blower assemblies with long life 12 volt DC permanent magnet motors with full ball bearings and extended life brushes.• Orifice tube/accumulator in lieu of TXV used in conjunction with highly efficient crosshatch copper tube and an aluminum fin coil for maximum capacity output and durability.• Standard manual controls or fully automatic. Electronic controls are pre-wired relays and circuit breakers. Relay board with electrical diagnostic LEDs can be mounted at evaporator or control panel at driver. • Utilizes our uniquely designed mounting system, eliminating the need to drill holes through the roof.• Available with heat.

Specifications:• 55,000 BTU/hr cooling capacity• 1200 cfm• Amp Draw High – 30 amps• 3 speed fans• 12 or 24 volts• Dimensions: 39.55”W x 13.95”H x 7.45”D• Weight – 65 lbs

Key Components:• Coil: X500-1147A• Blower Assembly: 26060040A• Orifice Tube:08800502A• Front Mount Cover:• Rear Mount Cover: (shown)


Features:• One dynamically balanced twin shaft blower assembly with long life 12 volt DC permanent magnet motors with full ball bearings and extended life brushes.• Orifice tube/accumulator in lieu of TXV used in conjunction with highly efficient crosshatch copper tube and an aluminum fin coil for maximum capacity output and durability.• Standard manual controls or fully automatic. Electronic controls are pre-wired relays and circuit breakers. Relay board with electrical diagnostic LEDs can be mounted at evaporator or control panel at driver. • Utilizes our uniquely designed mounting system, eliminating the need to drill holes through the roof.

Specifications:• 45,000 BTU/hr cooling capacity• 600 cfm• Amp Draw High – 15 amps• 3 speed fans• 12 or 24 volts• Dimensions: 39.55”W x 13.95”H x 7.45”D• Weight – 65 lbs

Key Components:• Coil: X500-1147A• Blower Assembly: 26060040A• Orifice Tube:08800502A• Front Mount Cover:• Rear Mount Cover: (shown)

ACC Climate Control, Inc. 25031 Series Condenser

Features:• Two 14” diameter fans to cover a higher percentage of the coil, 307 sq. in. moving more air than traditional condensers. High performance motors with extended brush life. Motor shafts are seated to the case which is sealed with Viton O-rings to provide superior water resistance.• Counter flow coil circuitry and cross hatch tubing maximizes the refrigerant heat rejection and provides superior sub-cooling.• The unit is fabricated from 16 ga. A-60 galvanealed steel with the individual metal components finished with an E-Kote epoxy coating for superior durability and resistance to rust.• Design allows for installation without having to cut condenser intakes in the skirt of the bus, (school bus only) providing a more aesthetic OEM look to the bus.

Specifications:• 78,000 BTU/hr capacity• 2500 cfm• Amp Draw High – 22 amps• 12 or 24 volts• Dimensions: 38.5”W x 20.25”H x 7.125”D• Weight – 62 lbs

Key Components:• Coil: 11471714A• Fan: 18000005B


Features:• Two 14” diameter fans to cover a higher percentage of the coil, 307 sq. in. moving more air than traditional condensers. High performance motors with extended brush life. Motor shafts are seated to the case which is sealed with Viton O-rings to provide superior water resistance.• Counter flow coil circuitry and cross hatch tubing maximizes the refrigerant heat rejection and provides superior sub-cooling.• The unit is fabricated from 16 ga. A-60 galvanealed steel with the individual metal components finished with an E-Kote epoxy coating for superior durability and resistance to rust.• Design allows for installation without having to cut condenser intakes in the skirt of the bus, (school bus only) providing a more aesthetic OEM look to the bus.

Specifications:• 92,000 BTU/hr capacity• 2500 cfm• Amp Draw High – 22 amps• 12 or 24 volts• Dimensions: 38.5”W x 20.25”H x 7.125”D• Weight – 67 lbs


Features:• Two 14” diameter high performance fans. High performance motors with extended brush life. Motor shafts are seated to the case which is sealed with Viton O-rings to provide superior water resistance.• Highly efficient 6mm coil design provides superior refrigerant heat rejection and provides superior sub-cooling.• The unit is fabricated from 16 ga. A-60 galvanealed steel with the individual metal components finished with an E-Kote epoxy coating for superior durability and resistance to rust.• Design allows for installation without having to cut condenser intakes in the skirt of the bus, (school bus only) providing a more aesthetic OEM look to the bus.

Specifications:• 62,000 BTU/hr capacity• 2500 cfm• Amp Draw High – 22 amps• 12 or 24 volts• Dimensions: 33.5”W x 11”H x 15”D• Weight – 62 lbs

Key Components:• Coil: 11471719A• Fan: 18000005B

ACC Climate Control, Inc.

Features: One 14” diameter high performance fan. High performance motor with extended brush life. Motor shafts are seated to the case which is sealed with Viton O-rings to provide superior water resistance. Highly efficient 6mm coil design provides superior refrigerant heat rejection and provides superior sub-cooling. The unit is fabricated from 16 ga. A-60 galvanealed steel with the individual metal components finished with an E-Kote epoxy coating for superior durability and resistance to rust. Design allows for installation without having to cut condenser intakes in the skirt of the bus, (school bus only) providing a more aesthetic OEM look to the bus.

Specifications: 35,000 BTU/hr capacity 1275 cfm Amp Draw High – 11 amps 12 volt Dimensions: 33.5”W x 11”H x 15”D Weight – 52 lbs

Key Components: Coil: 11471719B Fan: 18000005C

25035 Series Condenser

ACC Climate Control, Inc. 25045 Series Rooftop Condenser

Features:• Low Profile roof top design with overall height of 7 inches. • Two 14” diameter fans to cover a higher percentage of the coil, moving more air than traditional condensers. • High performance motors with extended brush life. Motor shafts are seated to the case which is sealed with Viton O-rings to provide superior water resistance.• Counter flow coil circuitry and cross hatch tubing maximizes the refrigerant heat rejection and provides superior sub-cooling.• The unit is fabricated from 16 ga. A-60 galvanealed steel with the individual metal components finished with an E-Kote epoxy coating for superior durability and resistance to rust.• Cover made of high impact molded plastic

Specifications: 78,000 BTU/hr capacity 2500 cfm Amp Draw High – 22 amps 12 or 24 volts Dimensions: 40” L x 40.5” W x 7” H Weight: @75 lbs

ACC Climate Control, Inc. 25047 Series Rooftop Condenser

Features:• Low Profile roof top design with overall height of 7 inches. • Two 14” diameter fans to cover a higher percentage of the coil, moving more air than traditional condensers. • High performance motors with extended brush life. Motor shafts are seated to the case which is sealed with Viton O-rings to provide superior water resistance.• Counter flow coil circuitry and cross hatch tubing maximizes the refrigerant heat rejection and provides superior sub-cooling.• The unit is fabricated from 16 ga. A-60 galvanealed steel with the individual metal components finished with an E-Kote epoxy coating for superior durability and resistance to rust.• Cover made of high impact molded plastic

Specifications: 100,000 BTU/hr capacity 2500 cfm Amp Draw High – 22 amps 12 or 24 volts Dimensions: 40” L x 40.5” W x 7” H Weight: @75 lbs


ACC “Tropicool” Roof Mount HVAC System

Features:Low Roof Profile of only 6.9 inches at centerline of busUnit width allows the direct discharge of evaporator air into the coach without the use of transitions required by other systems.Six (6) biaxial centrifugal type blower fansThree (3) axial-flow type condenser fansHigh impact fiber glass housing R134a RefrigerantAvailable in both single loop or dual loop refrigeration circuits for single or dual compressor applications

Specifications:96,000 BTU/hr cooling capacity120,000 BTU/hr heating capacityAutomatic or Manual Control2400 Evaporator cfmAmp Draw – @110 amps (12 Volts)3 speed fans12 or 24 voltsDimensions: 146.5 “ L x 73.3” W x 6.9” HWeight – @ 455 lbs


ACC Climate Control ATCO Air-O Crimp a/c Hose System

Features:Provides a Reliable Leak Free CrimpOne piece clamp assembly with stainless steel clamps Disposable clamp locator insures proper fitting alignmentQualified to SAE J2064 SpecificationLowest Refrigeration Permeation RateLow Moisture Ingression RateSuperior Abrasion Resistance – 3x That of Competition

Specifications:ATCO 3800 Barrier HoseATCO a/c Series Hybrid/Elastomer FittingsUse with PAG OilAvailable Air Crimp Gun, Model 3801Available Manual Crimping Pliers, Model 3802 (flat), or 3803 (90º)Available Cutter, Model 3541 Kwikcut Hose Cutter

ACC Climate Control, Inc. 23022 Series Evaporator Features: One dynamically balanced twin shaft...

Documents

Transcript of ACC Climate Control, Inc. 23022 Series Evaporator Features: One dynamically balanced twin shaft...