AC-DC conversion using microgenerator
-
Upload
engnr-areez-irfan -
Category
Engineering
-
view
29 -
download
5
Transcript of AC-DC conversion using microgenerator
![Page 1: AC-DC conversion using microgenerator](https://reader036.fdocuments.in/reader036/viewer/2022062515/55d28cedbb61eb344f8b4607/html5/thumbnails/1.jpg)
![Page 2: AC-DC conversion using microgenerator](https://reader036.fdocuments.in/reader036/viewer/2022062515/55d28cedbb61eb344f8b4607/html5/thumbnails/2.jpg)
ALLPPT.com _ Free PowerPoint Templates, Diagrams and Charts
DIRECT AC-DC ELECTRONIC CONVERTER TOPOLOGY.
Presented by:Bilal Ahmad. Areez Irfan.Hamza Ahmad.
![Page 3: AC-DC conversion using microgenerator](https://reader036.fdocuments.in/reader036/viewer/2022062515/55d28cedbb61eb344f8b4607/html5/thumbnails/3.jpg)
CONTENTS. Introduction.
Converter Topologies.
Implementation Design.
Simulation Results.
![Page 4: AC-DC conversion using microgenerator](https://reader036.fdocuments.in/reader036/viewer/2022062515/55d28cedbb61eb344f8b4607/html5/thumbnails/4.jpg)
Conventionally power electronic converters have two stages
a. Diode Bridge Rectifiers.
b. DC –DC Converters.
(It is less efficient and cant be used for electromagnetic microgenerators)
INTRODUCTION.
![Page 5: AC-DC conversion using microgenerator](https://reader036.fdocuments.in/reader036/viewer/2022062515/55d28cedbb61eb344f8b4607/html5/thumbnails/5.jpg)
For efficient and maximum energy direct AC-DC power
electronic converter topology is proposed.
The single stage AC to DC power conversion is
achieved by utilizing the bidirectional conduction capability of MOSFETs.
![Page 6: AC-DC conversion using microgenerator](https://reader036.fdocuments.in/reader036/viewer/2022062515/55d28cedbb61eb344f8b4607/html5/thumbnails/6.jpg)
ELECTROMAGNETIC MICROGENERATORS.
There are various microgenerators using different conversion
mechanisms but Electromagnetic microgenerators are common. Due to good power density. And they are typically spring-mass system.
Output:
Typically around few hundred millivolts.
Mechanical en-ergy
Electrical energy Electromagnetic damping
![Page 7: AC-DC conversion using microgenerator](https://reader036.fdocuments.in/reader036/viewer/2022062515/55d28cedbb61eb344f8b4607/html5/thumbnails/7.jpg)
` Power processing stage between transducer and load.
Output has to be processed by power converter to produce suitable DC output voltage.
Amount of energy conversion depends on the damping force.
Damping force can be varied by changing the effective
resistance.
![Page 8: AC-DC conversion using microgenerator](https://reader036.fdocuments.in/reader036/viewer/2022062515/55d28cedbb61eb344f8b4607/html5/thumbnails/8.jpg)
CONVERTER TOPOLOGIES.
A power converter is required for energy-harvesting applications.
Main function of the converter is to condition the AC output of the microgenerator to a suitable DC level and offer an adjustive resistive load to the microgenerator.
![Page 9: AC-DC conversion using microgenerator](https://reader036.fdocuments.in/reader036/viewer/2022062515/55d28cedbb61eb344f8b4607/html5/thumbnails/9.jpg)
Two stage power converter is not used for electromagnetic microgeneration Because :
a) Diode voltages in bridge rectifier are difficult to overcome for low input voltage.
b) Diode losses are increased as input current is much higher than output current.
c) A rectifier offers a nonlinear load, which makes the converter unsuitable for
energy harvesting.
Above disadvantages are eliminated with Direct AC-DC boost converters.
![Page 10: AC-DC conversion using microgenerator](https://reader036.fdocuments.in/reader036/viewer/2022062515/55d28cedbb61eb344f8b4607/html5/thumbnails/10.jpg)
DUAL POLARITY BOOST CONVERTER FOR
DIRECT AC-DC CONVERSION.
![Page 11: AC-DC conversion using microgenerator](https://reader036.fdocuments.in/reader036/viewer/2022062515/55d28cedbb61eb344f8b4607/html5/thumbnails/11.jpg)
PROPOSED DIRECT AC-DC CONVERTER:SPLIT-CAPACITOR TOPOLOGY.
![Page 12: AC-DC conversion using microgenerator](https://reader036.fdocuments.in/reader036/viewer/2022062515/55d28cedbb61eb344f8b4607/html5/thumbnails/12.jpg)
This operation has many advantages:
a) A constant duty cycle extracts constant power from source, enabling a simple control.
b) A converter operating with a constant duty cycle has only fundamental and switching harmonic frequency components and thus offers a resistive load to the microgenerator.
![Page 13: AC-DC conversion using microgenerator](https://reader036.fdocuments.in/reader036/viewer/2022062515/55d28cedbb61eb344f8b4607/html5/thumbnails/13.jpg)
The implementation of auxiliary circuits (gate driver and control circuits) is very important for low power applications. They are chosen in such a way
that they will consume very low power.
![Page 14: AC-DC conversion using microgenerator](https://reader036.fdocuments.in/reader036/viewer/2022062515/55d28cedbb61eb344f8b4607/html5/thumbnails/14.jpg)
Feedback control circuit.
Gate driver circuit.
Startup circuit.
![Page 15: AC-DC conversion using microgenerator](https://reader036.fdocuments.in/reader036/viewer/2022062515/55d28cedbb61eb344f8b4607/html5/thumbnails/15.jpg)
IMPLEMENTATION.
![Page 16: AC-DC conversion using microgenerator](https://reader036.fdocuments.in/reader036/viewer/2022062515/55d28cedbb61eb344f8b4607/html5/thumbnails/16.jpg)
SIMULATION RESULT.
![Page 17: AC-DC conversion using microgenerator](https://reader036.fdocuments.in/reader036/viewer/2022062515/55d28cedbb61eb344f8b4607/html5/thumbnails/17.jpg)
![Page 18: AC-DC conversion using microgenerator](https://reader036.fdocuments.in/reader036/viewer/2022062515/55d28cedbb61eb344f8b4607/html5/thumbnails/18.jpg)
Any Questions