AC, AXP, CB, CD, DOC · 2020. 12. 7. · Instruction Manual - Brazed plate heat exchangers AC, AXP,...

Instruction Manual -Brazed plate heat exchangers

AC, AXP, CB, CD, DOC

EN

3450021401-EN 2017-06Original manual

www.alfalaval.com/bhe-manuals

EnglishDownload local language versions of this instruction manualfrom www.alfalaval.com/bhe-manuals or use the QR code

българскиИзтеглете версиите на това ръководство за употребана местния език от www.alfalaval.com/bhe-manuals илиизползвайте QR кода.

ČeskýStáhněte si místní jazykovou verzi tohoto návodu k obsluze zwww.alfalaval.com/bhe-manuals nebo použijte QR kód.

DanskHent lokale sprogversioner af denne brugervejledning påwww.alfalaval.com/bhe-manuals eller brug QR-koden.

DeutschSie können die landessprachlichen Versionen diesesHandbuch von der Website www.alfalaval.com/bhe-manualsoder über den QR-Code herunterladen.

ελληνικάΠραγματοποιήστε λήψη εκδόσεων του παρόντοςεγχειριδίου οδηγιών σε τοπική γλώσσα από τοwww.alfalaval.com/bhe-manuals ή χρησιμοποιήστε τον κωδικόQR.

EspañolDescárguese la versión de este Manual de instrucciones ensu idioma local desde www.alfalaval.com/bhe-manualso utiliceel código QR.

EestiSelle kasutusjuhendi kohaliku keele versiooni saate allalaadida lingilt www.alfalaval.com/bhe-manuals või kasutadesQR-koodi.

SuomalainenLaitaa tämän käyttöohjeen suomenkielinen versio osoitteestawww.alfalaval.com/bhe-manuals tai QR-koodilla.

FrançaisTéléchargez des versions de ce manuel d’instructions endifférentes langues sur www.alfalaval.com/bhe-manuals ouutilisez le code QR.

HrvatskiPreuzmite lokalne verzije jezika ovog korisničkog priručnika napoveznici www.alfalaval.com/bhe-manuals ili upotrijebite QRkod.

MagyarAz Ön nyelvére lefordított használati útmutatót letöltheti awww.alfalaval.com/bhe-manuals weboldalról, vagy használja aQR-kódot.

ItalianoScarica la versione in lingua locale del manuale di istruzioni dawww.alfalaval.com/bhe-manuals oppure utilizza il codice QR.

日本のwww.alfalaval.com/bhe-manuals からご自分の言語の取扱説明書をダウンロードするか、QRコードをお使いください。

한국의www.alfalaval.com/bhe-manuals 에서 이 사용 설명서의 해당언어 버전을 다운로드하거나 QR 코드를 사용하십시오.

LatvijasAtsisiųskite šios instrukcijos versijas vietos kalba išwww.alfalaval.com/bhe-manuals arba pasinaudokite QR kodu.

LietuvosLejupielādējiet šīs rokasgrāmatas lokālo valodu versijas novietnes www.alfalaval.com/bhe-manuals vai izmantojiet QRkodu.

NederlandsDownload de lokale taalversies van de instructiehandleidingvanaf www.alfalaval.com/bhe-manuals of gebruik de QR-code.

NorskLast ned denne instruksjonshåndboken på lokalt språk frawww.alfalaval.com/bhe-manuals eller bruk QR-koden.

PolskiPobierz lokalne wersje językowe tej instrukcji obsługi zwww.alfalaval.com/bhe-manuals lub użyj kodu QR.

PortuguêsDescarregue as versões locais na sua língua deste manualde instruções a partir de www.alfalaval.com/bhe-manuals ouuse o código QR.

RomânescVersiunile în limba locală ale acestui manual de instrucţiunipot fi descărcate de pe www.alfalaval.com/bhe-manuals sauputeţi utiliza codul QR.

PусскийРуководство пользователя на другом языке вы можетезагрузить по ссылке www.alfalaval.com/bhe-manuals илиотсканировав QR-код.

SlovenskýMiestne jazykové verzie tohto návodu na používanie sistiahnite z www.alfalaval.com/bhe-manuals alebo použite QRkód.

SlovenskiPrenesite različice uporabniškega priročnika v svojem jezikus spletne strani www.alfalaval.com/bhe-manuals ali uporabitekodo QR.

SvenskaLadda ned lokala språkversioner av denna bruksanvisning frånwww.alfalaval.com/bhe-manuals eller använd QR-koden.

中国从 www.alfalaval.com/bhe-manuals 或使用 QR 码下载此使用说明书的本地语言版本。

www.alfalaval.com/bhe-manuals

Table of contents

Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11Name plates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12Lifting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15Installation in general . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16Installation as evaporator or condenser . . . . . . . . . . . . . 17Leak test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19Start-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19Unit in operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20Shut-down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23General guidelines regarding maintenance . . . . . . . . . . 23Cleaning-In-Place . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Fault tracing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25Pressure drop problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25Heat transfer problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

How to contact Alfa LavalContact details for all countries arecontinually updated on our website.Please visit www.alfalaval.com to access the information directly.

© Alfa Laval Corporate ABThis document and its contents is owned by Alfa Laval Corporate AB and protectedby laws governing intellectual property and thereto related rights. It is theresponsibility of the user of this document to comply with all applicable intellectualproperty laws. Without limiting any rights related to this document, no part of thisdocument may be copied, reproduced or transmitted in any form or by any means(electronic, mechanical, photocopying, recording, or otherwise), or for any purpose,without the expressed permission of Alfa Laval Corporate AB. Alfa Laval CorporateAB will enforce its rights related to this document to the fullest extent of the law,including the seeking of criminal prosecution.

Document ID Language Edition

3450021401 EN 2017-06Instruction Manual -

Brazed plate heat exchangers 7

EN

Preface

Preface

This manual provides information needed to install, operateand carry out the maintenance of the plate heat exchanger.

Intended useThe plate heat exchanger has been designed to meet therequirement for a wide range of heat transfer applications suchas refrigeration, comfort heating, industrial heating and cooling,and the process industry.

Safety considerationsThe plate heat exchanger must be used and maintainedin accordance with the instructions in this manual. Faultyhandling of the plate heat exchanger may result in serious withinjuries and/or property damage. Alfa Laval will not acceptresponsibility for any damage or injury caused as a result ofnot following the instructions in this manual.

The plate heat exchanger must be used in accordance with thespecified configuration of material, media, temperatures andpressure for the specific plate heat exchangers.

Prior knowledgeThe plate heat exchanger must be operated by individualswho have studied the instructions in this manual and haveknowledge of the process. This includes knowledge of theprecautions regarding media, pressures, the temperaturesin the plate heat exchanger as well as specific precautionsrequired for the process.

Maintenance and installation of the plate heat exchangermust be performed by individuals who have knowledge andauthorization according to the local regulations. This includesperformance work such as piping, welding and maintenance.

For maintenance work not described in this manual, pleasecontact an Alfa Laval Representative for advice.


8

Instruction Manual -

Brazed plate heat exchangers 3450021401 EN 2017-06

Preface

Definitions of expressions

Warning!Type of hazardWARNING indicates a potentially hazardous situationthat, if not avoided, may result in death or seriousinjury.

Caution!Type of hazardCAUTION indicates a potentially hazardous situationthat, if not avoided, may result in minor or moderateinjury.

Note!NOTE indicates a potentially hazardous situation that,if not avoided, may result in property damage.

Warranty conditionsUnless altered by written agreement, Alfa Laval standardwarranty applies.

Storage of the plate heat exchangersAlfa Laval delivers the plate heat exchanger ready foroperation, unless agreed otherwise. Keep the plate heatexchanger in the packing box until it is ready to be installed.

If there is any uncertainty with regard to the storage of the plateheat exchanger, please consult an Alfa Laval Representative.

For longer storage periods, keep the heat exchanger in aprotective environment away from corrosive substances anddust which may affects its performance.

Keep the plastic plugs or caps for the connections in placeduring storage.




EN

Preface

Environmental complianceAlfa Laval endeavours to perform its own operations as cleanlyand efficiently as possible. Environmental aspects are takeninto consideration when developing, designing, manufacturing,servicing and marketing the company’s products.

Brazed Plate Heat Exchangers (BHE) consist of stainless steelchannel plates and frame elements and bonded stainless steelor carbon steel connections. Bolts, which are stainless steelor carbon steel with different surface treatments, are usuallywelded onto the product. Additionally, feet and lifting lugs canbe mounted on demand.

UnpackingPacking material consists of wood, plastics, cardboard boxesand, in some cases, metal straps.

Packing materials can be reused, recycled or used for energyrecovery, according to local legislations.

DisposalHeat exchangers must be recycled according to relevant, localregulations. Any hazardous residues from the process liquidmust be considered and dealt with in a properly. When indoubt, or in absence of local regulations, please contact thelocal Alfa Laval representative.

Restricted substancesAll plate heat exchangers are in compliance with REACH(Registration, Evaluation, Authorization and Restriction ofChemicals) and RoHS Directive.


10



Description

Description

FunctionPlate heat exchangers consist of a pack of corrugated metalplates with ports for the passage of the two fluids betweenwhich the heat transfer will take place.

The media in the heat transfer are led into the plate packthrough portholes at the corners and are distributed into thepassages between the corrugated plates.

1

2

3

4

Figure 1. Function: Cover plate (1), corrugated plates (2), seal(3) and ports (4).

Warning!The heat exchanger must not be opened.

Name plates

Warning!The mechanical design pressures and temperaturesare marked on the name plate. These must not beexceeded.

The unit type, manufacturing number and year along with thepressure vessel details in accordance with applicable pressurevessel code can be found on the name plate. The name plateis fixed to the cover plate (usually on the same side as theconnections).

Name plate differs depending on the type of pressure vesselapproval.




EN

Installation

Installation

UnpackingCarefully open the package containing the plate heatexchanger. Check that all items are included according to thespecifications and that all parts are undamaged.

Before installing the plate heat exchanger, remove the plasticplugs or caps in the connections.

Lifting

Warning!Never lift only by the connections or anyb of the studs.Use straps when lifting and place them according tothe figure below.

Figure 2. Examples of lifting.

Note!When using lifting lugs, keep the angle of the strapsas close as possible to 90° but never less than 60°.

Warning!Be careful and keep clear of the heat exchangerduring lifting to avoid personal injuries.


12



Installation

Warning!Plate heat exchangers with large plate packs may bedifficult to lift without lifting lugs because the center ofgravity may cause the plate heat exchanger lean toomuch. If in doubt, use lifting lugs.

Requirements

Warning!The plate heat exchanger must be installed andoperated so that no risk of injury to personnel ordamage to property.

Caution!Protective gloves should always be worn whenhandling the plate heat exchanger to avoid handinjuries caused by sharp edges.

Note!Unless otherwise specified, product data for normalrefrigerants, i.e. HFC and HCFC, are applicableto refrigeration applications. The manufacturermust be consulted before the heat exchanger isused for flammable, toxic or dangerous liquids(e.g. hydrocarbons). Relevant safety rules mustbe followed for handling such liquids. For furtherinformation, please refer to the supplier’s website.

Protection against loads on connections during operationThe piping must be well supported so that no loads aretransferred to the heat exchanger during operation. Also referto “Mounting” on page 15.




EN

Installation

Connection loads at installation

Fs

Ft

Mt

Mb

Figure 3. Connection loads.

With reference to definitions in figure, the loads duringinstallation should not exceed the limits specified in table below.

Maximum recommended connection loads duringinstallation

D

Figure 4. Outer diameter of the connection (D).

Tensionforce

Bendingmoment

Shearforce1

TorqueOuter diametermm (inch)

FtkN (lbf)

MbNm

(lbf*ft)

FskN (lbf)

MtNm

(lbf*ft)15 -28

(0.6 - 1.1”)2.4

(539)14

(10.3)0.7

(157)38

(28.0)29 - 35

(1.1 - 1.4”)4.0

(899)45

(33.2)1.2

(269)120

(88.5)36 - 45

(1.4 - 1.8”)6.5

(1461)110

(81.1)2.5

(562)240

(177.0)46 - 55

(1.8 - 2.2”)7.0

(1573)120

(88.5)4.8

(1079)440

(324.5)56 - 76

(2.2 - 3.0”)12.0

(2697)250

(184.4)5.2

(1169)600

(442.5)77 - 99

(3.0 - 3.9”)13.0

(2922)310

(228.6)5.8

(1303)1200

(885.0)100 -

(3.9” - )28.0

(6294)800

(590)5.8

(1303)2500

(1843)

1. Shear force (Fs) is calculated assuming that the force isapplied at the end of the longest standard connection.


14



Installation

MountingIt is recommended to mount the plate heat exchanger on thefloor, on feet or on the wall.

Larger heat exchangers should be secured with supportmountings (ordered as accessory) intended for a specific heatexchanger, or be secured with straps or by means of mountingbolts.

Note!Regardless of the mounting method minimize thepipe loads at installation.

Maximum tightening torques for the mounting bolts accordingto table below.

Bolt dimension TorqueNm lbf*ft

M5 2.3 1.7M6 3.8 2.8M8 9.5 7.0

M8 (Extra small units) 8.0 5.9M10 19.0 14.0M12 33.0 24.3

UNC 1/4” 3.8 2.8UNC 5/16” 8.6 6.4UNC 3/8” 15.6 11.5

In a rigid pipe system, small heat exchangers can besuspended directly in the pipework. To avoid vibrations, useanti-vibration mounting according to picture below.




EN

Installation

Installation in general

Warning!Safety valves must be installed according to pressurevessel regulations.

Note!Before connecting any piping, make sure all foreignobjects have been flushed out of the system.

The installation must be installed with equipment that protectsit against pressures and temperatures outside the approvedminimum and maximum values shown on the name plate.

For vibration risks, install anti-vibration mountings as shown inpicture for rigid pipe system in section Mounting at page 15.

Normally the plate heat exchanger is connected so that themedia flows through the plate heat exchanger in oppositedirections (in counter-current flow) and in most cases thisprovides the best heat transfer performance.

S4 S1

S3 S2

Take into account the risk of fire during installation, i.e. bear inmind the distance from flammable substances.

ConnectionsThreaded connections – Use a torque wrench whenconnecting the pipe and observe the specified limits. Refer totable on page 14.

Brazed connections – Clean by rubbing down and degreasingthe various surfaces. Use the correct brazing temperature andbrazing metal grade.


16



Installation

Welded connections – To minimize the heat impact of theheat exchanger it is recommended to use TIG or MIG weldingmethods. Preparation for welding: Grind inside and outsideof the pipe and, if bevelled, also the bevelled edge at least25 mm from the pipe edge and inward. This should be doneto avoid contamination of copper in the welded area, whichmight cause the weld to crack.

Note!Before connecting the heat exchanger to the systemconsider valve set-up and access points for exampleto be prepared to perform cleaning.

Note!Protect the heat exchanger from overheating bywrapping a piece of wet cloth around the connectionwhile soldering or welding. Excessive heating couldmelt the internal soldering metal inside the heatexchanger.

Installation as evaporator or condenserIn applications where a phase change of media occurs, theheat exchanger must be installed vertically.

For refrigeration applications – Figure A shows the installationof an evaporator, which the connections may be either on thefront or on the rear. Figure B shows a condenser.

• Use an anti-freeze thermostat and flow monitor to ensure aconstant water flow before, during, and at least two minutesafter the compressor has been running.

• Avoid “pump-down”, i.e. emptying the evaporator byrunning the compressor after shut-down until a presetrefrigerant pressure is reached. The temperature could thendrop below the brine freezing point, which could damagethe evaporator.

• Use a flow switch and a low-pressure switch.• Make sure only media from the heat exchanger can pass

the flow switch. The low-pressure switch should assure aminimum pressure drop of 5 - 10 kPa (0.73 - 1.45 PSI).




EN

Installation

Heat exchanger with a refrigerant distribution system shouldbe mounted with the distributor at the bottom.

Typical installation of single circuit:

S4 S1

S3 S2

S4 S1

S3 S2

A B

3

4

2

1

4

3

1

2

Figure 5. Single circuit: A evaporator; B condensor.1.Refrigerant inlet 2.Refrigerant outlet3.Water/Brine inlet 4.Water/Brine outlet

For an evaporator, the pipe should be straight (at least 150 mm/ 5.9 inch length) between the expansion valve and refrigerantinlet. Avoid using pipe elbows between the expansion valveand the refrigerant inlet.

The heat exchanger could be of single or dual circuit type.Flow direction of a single circuit heat exchanger is normallyparallel, while on dual circuit heat exchanger could be diagonalor parallel. Make sure that the heat exchanger is installedcorrectly according to the current flow direction for the heatexchanger. For detailed information about flow direction seethe name plate.

Connections can be placed in the front or rear of the heatexchanger. Typical installation of a dual circuit heat exchangeras an evaporator:

S1

S2

S4.2 S4.1

S3.1 S3.2

S1

S2

S4.2 S4.1

S3.1 S3.2

A B

2

1 1

2

Figure 6. Dual circuit: A is parallel flow; B is diagonal flow.1.Refrigerant inlet 2.Refrigerant outletWater/Brine inlet and outlet are typically positioned on therear side.

Leak testPerform leakage test before placing the plate heat exchangerin operation.


18



Operation

Operation

Start-up

Note!If several pumps are included in the system, makesure you know which one should be activated first.

Note!Adjustments of flow rates should be made slowly inorder to avoid the risk of water hammer.Water hammer is a short-lasting pressure peak thatcan appear during start-up or shut-down of a system,which causing liquids to travel along a pipe as a waveat the speed of sound. This can cause considerabledamage to the equipment.

Step 1Check that the inlet valve (2) is closed between the pump andthe unit controlling the system flow rate.Inlet valve (2, 3) for both fluids should be closed, the outletvalves (1, 4) opened and the vent valve (5, 6) closed.

1

3

2

4

65

Step 2If there is a outlet valve (4), make sure that it is fully open.

Step 3Open the vent valve (5) and start the pump.

Step 4Open the inlet valve (2) slowly.




EN

Operation

Step 5When all air is expelled, close the vent valve (5).

Step 6Repeat steps 1–5 for the second media.

Unit in operation

Note!Adjustments of flow rates should be made slowlyin order to protect the system against sudden andextreme variations of temperature and pressure.

During operation, check that:

• media temperatures and pressures are within the limitsstated on the name plate

• no leakages appear due to faulty tightening of theconnections.

Protection against connection loadsMake sure that the heat exchanger is fastened to avoid orminimize connection loads during operation.

Protection against freezingBear in mind the risk of freezing at low temperatures. Plateheat exchangers that are not in operation should be emptiedand blown dry whenever there is a risk of freezing.

Note!To avoid damage due to freezing, the medium usedmust include an anti-freeze agent when operatingconditions are below 5 °C (41 °F) and/or when theevaporating temperature is below 1 °C (34 °F).

Protection against cloggingUse a filter as protection against the possible occurrenceof foreign particles. If you have any doubt concerningthe maximum particle size, please consult your Alfa LavalRepresentative.


20



Operation

Protection against thermal or/and pressure fatigueSudden temperature and pressure changes could cause fatiguedamage to the heat exchanger. Therefore, the following mustbe taken into consideration to ensure that the heat exchangeroperates without fluctuating pressures/temperatures.

Warning!The plate heat exchanger is not intended forcyclic processes, please contact an Alfa LavalRepresentative for advice.

• Locate the temperature sensor as close as possible to theoutlet from the heat exchanger.

• Choose valves and regulation equipment which give stabletemperatures/pressures for the heat exchanger.

• To avoid water hammer, quick-closing valves must not beused, e.g. on/off valves.

• In automated installations, stopping and starting of thepumps and actuation of valves must be programmed sothat the amplitude and frequency of the pressure variationare as low as possible.

Protection against corrosion

Caution!Do not use the heat exchanger for de-ionized wateras this media can chemically affect the copper brazingmaterial.Do not use the heat exchanger for installations withgalvanized pipes that chemically or electrochemicallycould affect or be affected by the stainless steel platesand the copper brazing material.

Note!Copper may generate corrosion in installation withmixed materials.

Caution!Avoid ammonia or other media that could be corrosiveto stainless steel and copper.




EN

Operation

Recommended limits for Chloride ions, Cl- at pH 7.5 1 2Alloy 304 Alloy 316

at 25 °C / 77 °F 100 ppm 1000 ppmat 65 °C / 149 °F 50 ppm 200 ppmat 80 °C / 176 °F 20 ppm 100 ppm

1. Lower levels of chloride ions may cause corrosion due toother factors.2. Halogens, e.g. bromides and flourides may also causecorrosion.

InsulationIf the heat exchanger will be operated at very hot or very coldtemperature, take protective actions, such as insulation, toavoid injuries. Be certain to follow all local regulations.

Heating and cooling insulations are available as accessories.

Be aware that temperature limits of insulation and the heatexchanger can be different.

Shut-down

Note!If several pumps are included in the system, makesure you know which one should be stopped first.

1. Slowly reduce the flow rate in order to avoid water hammer.2. When the valve is closed, stop the pump.3. Repeat steps 1–2 for the other medium/media.4. If the plate heat exchanger is shut down for a long period, it

should be drained.Also, drain the heat exchanger if the process is shutdown and the ambient temperature is below the freezingtemperature of the media.Depending on the media processed, rinse and dry the heatexchanger and its connections.


22



Maintenance

Maintenance

Cleaning can improve the performance of the plate heatexchanger. Cleaning intervals depends on factors such asmedia and temperatures.

General guidelines regarding maintenance

Plate Sheet materialStainless steel can corrode. Chloride ions are hazardous.

Avoid cooling brines containing chloride salts as NaCI and,most harmful, CaCI2.

Chlorine as a growth inhibitor

Note!Chlorine, commonly used as a growth inhibitorin cooling water systems, reduces the corrosionresistance of stainless steels.Chlorine weakens the passive layer of these steelsmaking them more susceptible to corrosion. This isdependent on exposure time and concentration ofchlorine.

In every case where the chlorination of the plate heatexchanger cannot be avoided, consult an Alfa LavalRepresentative for advice.

Cleaning-In-PlaceCleaning-In-Place (CIP) equipment permits cleaning of theplate heat exchanger.

CIP performs:

• By regular CIP, the dissolution of fouling helps to restore theoriginal thermal performance of the unit.

• The passivating effect by the CIP procedure can helpto maintain the original corrosion resistance of the platematerial.




EN

Maintenance

Type of cleaning:

• Acidic cleaning removes inorganic deposits such aslimestone.

• Alkaline cleaning removes organic deposits. During theprocess it is important to control the pH value and therecommended pH value is 7.5 - 10. Higher pH valuesincrease risk of the copper oxidizing.

• Neutralization of cleaning liquids before draining andflushing the unit with potable water.

Follow the instructions of the CIP equipment.

Consult an Alfa Laval Representative for approriate adviceon selecting CIP equipment.

Warning!Use proper protective equipment, such as safetyboots, safety gloves and eye protection, when usingcleaning agents.

Warning!Corrosive cleaning liquids can cause serious injuriesto skin and eyes!

For detailed information regarding Cleaning liquids andprocedure, refer to the CIP manual.

Rinse well with fresh water after cleaning.

Caution!Make sure that the handling of residuals after usingcleaning liquids follows the local environmentalregulations.


24



Fault tracing

Fault tracing

Pressure drop problemsIf the pressure drop has increased.

Action1.Check that all valves are open including non-return valves.- Measure the pressure and the flow rate directly in front ofthe inlet and after the outlet of the heat exchanger.For viscousmedia use a membrane manometer with a diameter of atleast 30 mm.- Measure or estimate the flow rate if possible. A bucket and awatch showing seconds may be sufficient for small flow rates.For larger flow rates, use a flowmeter.CorrectionYES -NO -

Action2.Compare the pressure drop observed with the specifiedflow rate (see data printout). Is the pressure drop higher thanspecified?CorrectionYES Check the temperature program, see step 3NO If the pressure drop corresponds to the specifications,

there is no need for action. If the pressure drop islower than specified, the pump capacity is probablytoo small or the observation may be wrong. See pumpinstruction manual.

Action3.Check the thermometer readings. Do the readingscorrespond to those specified?CorrectionYES The heat transfer surface is probably clean enough,

but the inlet to the heat exchanger may be clogged bysome objects. Check the port area.

NO Heat transfer is obviously dropping belowspecifications, because of deposits on the heattransfer surface, which at the same time alsoincreases the pressure drop, since the passagebecomes narrower.If a Cleaning-In-Place (CIP) system is available, followthe instructions and use it to wash out the deposits.




EN

Fault tracing

Heat transfer problemsThe heat transfer capacity is dropping.

Action1.Measure temperatures at inlets and outlets. Also measureflow rates on both media, if possible. On at least one ofthe media, both temperatures and the flow rate must bemeasured.Check to see if the transferred amount of heat energycorresponds to the specifications.If great precision is important, it will be necessary to uselaboratory thermometers with an accuracy of 0.1 °C, and alsoto use the best equipment available for flow measurement.Has the heat transfer capacity of the unit dropped belowspecified values?CorrectionYES Clean the heat transfer surface. Use the

Cleaning-In-Place (CIP) system.NO -


26



tocPreface Intended use Safety considerations Prior knowledge Definitions of expressions Warranty conditions Storage of the plate heat exchangers Environmental compliance UnpackingDisposalRestricted substances

Description Function Name plates

Installation Unpacking Lifting Requirements Protection against loads on connections during operationConnection loads at installationMaximum recommended connection loads during installation

Mounting Installation in general Connections

Installation as evaporator or condenser Leak test

Operation Start-up Unit in operation Protection against connection loadsProtection against freezingProtection against cloggingProtection against thermal or/and pressure fatigueProtection against corrosionInsulation

Shut-down

Maintenance General guidelines regarding maintenance Plate Sheet materialChlorine as a growth inhibitor

Cleaning-In-Place

Fault tracing Pressure drop problems Heat transfer problems

/ColorImageDict > /JPEG2000ColorACSImageDict > /JPEG2000ColorImageDict > /AntiAliasGrayImages false /CropGrayImages true /GrayImageMinResolution 150 /GrayImageMinResolutionPolicy /OK /DownsampleGrayImages false /GrayImageDownsampleType /Bicubic /GrayImageResolution 300 /GrayImageDepth -1 /GrayImageMinDownsampleDepth 2 /GrayImageDownsampleThreshold 1.50000 /EncodeGrayImages true /GrayImageFilter /DCTEncode /AutoFilterGrayImages true /GrayImageAutoFilterStrategy /JPEG /GrayACSImageDict > /GrayImageDict > /JPEG2000GrayACSImageDict > /JPEG2000GrayImageDict > /AntiAliasMonoImages false /CropMonoImages true /MonoImageMinResolution 1200 /MonoImageMinResolutionPolicy /OK /DownsampleMonoImages false /MonoImageDownsampleType /Bicubic /MonoImageResolution 1200 /MonoImageDepth -1 /MonoImageDownsampleThreshold 1.50000 /EncodeMonoImages true /MonoImageFilter /CCITTFaxEncode /MonoImageDict > /AllowPSXObjects true /CheckCompliance [ /None ] /PDFX1aCheck false /PDFX3Check false /PDFXCompliantPDFOnly false /PDFXNoTrimBoxError true /PDFXTrimBoxToMediaBoxOffset [ 0.00000 0.00000 0.00000 0.00000 ] /PDFXSetBleedBoxToMediaBox true /PDFXBleedBoxToTrimBoxOffset [ 0.00000 0.00000 0.00000 0.00000 ] /PDFXOutputIntentProfile (None) /PDFXOutputConditionIdentifier () /PDFXOutputCondition () /PDFXRegistryName (http://www.color.org) /PDFXTrapped /False

/CreateJDFFile false /SyntheticBoldness 1.000000 /Description >>> setdistillerparams> setpagedevice

AC, AXP, CB, CD, DOC · 2020. 12. 7. · Instruction Manual - Brazed plate heat exchangers AC, AXP,...

Documents

Transcript of AC, AXP, CB, CD, DOC · 2020. 12. 7. · Instruction Manual - Brazed plate heat exchangers AC, AXP,...