ABSTRACT The purpose of this project is to develop an amplifier for Teradyne Corporation. The...

1
ABSTRACT The purpose of this project is to develop an amplifier for Teradyne Corporation. The amplifier will take the input signal and amplify it without introducing additional noise and distortion. This will be accomplished by two amplifiers in resistive feedback with DC offset correction and frequency response calibration. This device will be used as a pre-amplifier for the spectrum analyzer developed in Phase I and II. INTRODUCTION General Background Teradyne requested a pre-amplifier for the spectrum analyzer designed in the previous two phases. The spectrum analyzer will be used on the Integra J750 Enhanced Digital Channel Board, which tests large numbers of digital chips for other companies Technical Problems Correct operation of the amplifier requires: •DC offset less than 1mV •Pass-band flatness of 0.1dB •Low noise and low distortion •Bandwidth of 100MHz Operating Environment •The system will be used in a climate-controlled laboratory Intended Users and Uses •Teradyne engineers and technicians are the sole intended users •Teradyne will use the spectrum analyzer to test silicon chips Assumptions •Appropriate parts can be acquired •Necessary equipment will be made available •The Teradyne engineers are familiar with the operation of a spectrum analyzer Limitations •The design team is limited to 4 members •There is limited time to complete the project •Funding is limited to $3,100 DESIGN REQUIREMENTS Functional Requirements •Ability to amplify signals from DC to 100MHz •Variable gain settings •Programmable DC offset correction •Active frequency response calibration Design Constraints High quality, precision amplifiers having large bandwidths and near 90˚ phase margins are required to amplify signals up to 100MHz. Measurable Milestones •Schematic level implementation — Design of the device at the schematic level coupled with Spice simulations to verify functionality and design requirements. •PC board layout — The device must be carefully laid out onto a PC board. •Fabrication — An outside contractor will fabricate the device onto a PC board. •Testing The final product will be tested to guarantee it meets all design requirements. •Deliver Product — All data will be assembled into a final report. The product will be delivered to Teradyne. END PRODUCT The final product will be fabricated onto a PC board. DIP switches will be used to program the variable gain and DC offset. The team is divided into two groups: •The first group will research amplifier topologies •The second group will research DC and frequency response correction methodologies BUDGET AND EFFORT Contact Information Client Advisor Team Members [email protected] Teradyne Corporation Dr. Degang Chen Michael Cain http://seniord.ee.iastate.edu/may0310 Michael McNally Paul Heil OPERATIONAL DIAGRAM TESTING DESCRIPTION Testing will be completed at Iowa State University or Teradyne facilities. Equipment from the subsequent facility will be used. M A Y 0 3 – 1 0 SPECTRUM ANALYZER TECHNICAL APPROACH $2,000 $1,000 $100 Board Fabrication Components Project Poster Figure 2: Financial Budget Resistive Network DC Offset Correction OP amp DC Offset Correctio n OP amp Frequency Response Correctio n Programming Network 60dB 40dB 20dB 6dB DC Offset Figure 1: Block Diagram 0 50 100 150 200 250 Eric Aung Paul Mike hrs Delivery Testing Fabrication Layout Schematic Figure 3: Personal Budget

Transcript of ABSTRACT The purpose of this project is to develop an amplifier for Teradyne Corporation. The...

Page 1: ABSTRACT The purpose of this project is to develop an amplifier for Teradyne Corporation. The amplifier will take the input signal and amplify it without.

ABSTRACT

The purpose of this project is to develop an amplifier for Teradyne Corporation. The amplifier will take the input signal and amplify it without introducing additional noise and distortion. This will be accomplished by two amplifiers in resistive feedback with DC offset correction and frequency response calibration. This device will be used as a pre-amplifier for the spectrum analyzer developed in Phase I and II.

INTRODUCTION

General Background

Teradyne requested a pre-amplifier for the spectrum analyzer designed in the previous two phases. The spectrum analyzer will be used on the Integra J750 Enhanced Digital Channel Board, which tests large numbers of digital chips for other companies

Technical Problems

Correct operation of the amplifier requires:•DC offset less than 1mV•Pass-band flatness of 0.1dB •Low noise and low distortion •Bandwidth of 100MHz

 Operating Environment

•The system will be used in a climate-controlled laboratory

 Intended Users and Uses

•Teradyne engineers and technicians are the sole intended users •Teradyne will use the spectrum analyzer to test silicon chips

 Assumptions

•Appropriate parts can be acquired•Necessary equipment will be made available•The Teradyne engineers are familiar with the operation of a spectrum analyzer

 Limitations

•The design team is limited to 4 members•There is limited time to complete the project•Funding is limited to $3,100

DESIGN REQUIREMENTS

Functional Requirements

•Ability to amplify signals from DC to 100MHz•Variable gain settings•Programmable DC offset correction•Active frequency response calibration

Design Constraints

High quality, precision amplifiers having large bandwidths and near 90˚ phase margins are required to amplify signals up to 100MHz.

Measurable Milestones

•Schematic level implementation — Design of the device at the schematic level coupled with Spice simulations to verify functionality and design requirements.

•PC board layout — The device must be carefully laid out onto a PC board.

•Fabrication — An outside contractor will fabricate the device onto a PC board.

•Testing — The final product will be tested to guarantee it meets all design requirements.

•Deliver Product — All data will be assembled into a final report. The product will be delivered to Teradyne.

END PRODUCT

The final product will be fabricated onto a PC board. DIP switches will be used to program the variable gain and DC offset.

The team is divided into two groups:•The first group will research amplifier topologies

•The second group will research DC and frequency response correction methodologies

BUDGET AND EFFORT

Contact Information Client Advisor Team Members

[email protected] Teradyne Corporation Dr. Degang Chen Michael Cain

http://seniord.ee.iastate.edu/may0310 Michael McNally Paul Heil

Lee Moore Eric Rasmussen

Aung Thuya

OPERATIONAL DIAGRAM

TESTING DESCRIPTION

Testing will be completed at Iowa State University or Teradyne facilities. Equipment from the subsequent facility will be used.

 

M A Y 0 3 – 1 0SPECTRUM ANALYZER

TECHNICAL APPROACH

$2,000

$1,000

$100

Board Fabrication

Components

Project Poster

Figure 2: Financial Budget

Resistive Network

DC Offset Correction OP amp

DC Offset Correction OP amp

Frequency Response Correction

Programming Network

60dB 40dB 20dB 6dB DC Offset

Figure 1: Block Diagram

0

50

100

150

200

250

Eric Aung Paul Mike

hrs

Delivery

Testing

Fabrication

Layout

Schematic

Figure 3: Personal Budget