Absco Aviary Assembly Instructions Model:...
Transcript of Absco Aviary Assembly Instructions Model:...
![Page 1: Absco Aviary Assembly Instructions Model: A15301FKabscosheds.com.au/pdf/Instructions/A15301FK_(J).pdf · notched corners to bottom of sheets lay these sections over the panel as shown,](https://reader036.fdocuments.in/reader036/viewer/2022081607/5ed6ae0739f16f294d5743f9/html5/thumbnails/1.jpg)
PAGE 1ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: A15301FK 28/04/16
1620m
m
FRONT: 1.52m
SIDE : 2.96m
HEIGHT: 1.8m
3
0
6
0
m
m
We thank you for choosing an Australian Made Aviary.
For further assistance please visit our detailed instructional video library at
www.abscosheds.com.au/watch-videos
At ABSCO Industries we are always looking to be number ONE, so please let us
know what you think of our instructions. Feedback makes us better.
10mm
50mm
WHEN LAYING YOUR CONCRETE
SLAB, CHAMFER THE 50mm EDGES
DOWNWARDS BY 10mm.
5
0
m
m
THIS WILL ENSURE THAT
CLEAR FROM YOUR SHED
WATER RUN OFF IS KEPT
CO
NC
RE
TE
SL
AB
Absco AviaryAssembly InstructionsModel: A15301FK
![Page 2: Absco Aviary Assembly Instructions Model: A15301FKabscosheds.com.au/pdf/Instructions/A15301FK_(J).pdf · notched corners to bottom of sheets lay these sections over the panel as shown,](https://reader036.fdocuments.in/reader036/viewer/2022081607/5ed6ae0739f16f294d5743f9/html5/thumbnails/2.jpg)
PAGE 2ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: A15301FK 28/04/16
Absco Aviary Model: A15301FK
GENERAL INSTRUCTIONS
A NOTE ON SAFETY
· The site for the aviary must be level.
· It is recommended that the aviary be set on a 100mm concrete slab and
anchored down appropriately (refer page 21 for details).
· Anchor sets are not supplied as standard items with this product.
· Before commencing any assembly, read through these instructions in
detail to gain a thorough understanding of assembly methods and
associated details.
· Unpack the carton and carefully identify and check off all the parts
against the parts described and illustrated on pages three and four.
· Some parts may have sharp edges. It is advisable to wear gloves when
handling these items and safety glasses if drilling holes. Sensible shoes
are highly recommended.
· Do not erect your aviarie in windy conditions, ensure that the shed is
securely anchored to a solid foundation immediately after construction is
completed.
· It is highly recommended to erect the shed with two or more people.
TOOLS REQUIRED
3mm
4mm
SITE PREPARATION
![Page 3: Absco Aviary Assembly Instructions Model: A15301FKabscosheds.com.au/pdf/Instructions/A15301FK_(J).pdf · notched corners to bottom of sheets lay these sections over the panel as shown,](https://reader036.fdocuments.in/reader036/viewer/2022081607/5ed6ae0739f16f294d5743f9/html5/thumbnails/3.jpg)
COMPONENTS PACKING LIST - CHECK OFF ALL COMPONENTS
PAGE 3ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: A15301FK 28/04/16
Absco Aviary Model: A15301FK
COMPONENT
DESCRIPTION
PART
No.
CHECK
COMPONENT
DESCRIPTION
PART
No.
CHECKQTY QTY
1785mm X 773mm
30A
STEEL SHEET
4
1592mm X 773mm
43A
STEEL SHEET
4
1785mm X 731mm
33A
STEEL SHEET
2
585mm X 773mm
154
STEEL SHEET
3
5
1220mm X 712mm
MESH SHEET
590mm X 712mm
MESH SHEET
1
-
-
1
DOOR
PRE-ASSEMBLED
-
CHANNEL
L = 1513mm
164
2
CHANNEL
L = 1513mm
81F
2
181
CHANNEL
L = 712mm
13
191
JAMB L= 1785mm
11
192
JAMB L= 1785mm
1
195
JAMB L= 712mm
1
288A
LIP TRIM L= 1592mm
172
CHANNEL
L = 1745mm
2
1
FITTINGS AND
ACCESSORIES
(SEE OVER)
585mm X 773mm
154L
STEEL SHEET
1
585mm X 773mm
154R
STEEL SHEET
1
Part No. Here
ALL SHEETS HAVE PART NO.S LOCATED ON
LOWER RIGHT OR UPPER LEFT CORNER OF
COLORED SIDE AS SHOWN
![Page 4: Absco Aviary Assembly Instructions Model: A15301FKabscosheds.com.au/pdf/Instructions/A15301FK_(J).pdf · notched corners to bottom of sheets lay these sections over the panel as shown,](https://reader036.fdocuments.in/reader036/viewer/2022081607/5ed6ae0739f16f294d5743f9/html5/thumbnails/4.jpg)
PAGE 4ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: A15301FK 28/04/16
Absco Aviary Model: A15301FK
CONTENTS OF FITTINGS PACKET
COMPONENTS PACKING LIST - (CONT.) CHECK OFF ALL COMPONENTS
100
200
SELF TAPPING
SCREWS
1DOOR
PADBOLT
1
DOOR
PADBOLT
HASP
6
SMALL FLANGE
POP-RIVETS
1
ASSEMBLY
INSTRUCTIONS
22A
LARGE FLANGE
POP-RIVETS
COMPONENT
DESCRIPTION
PART
No.
CHECK
COMPONENT
DESCRIPTION
PART
No.
CHECKQTY QTY
CHANNEL
L = 1475mm
166R
2
167R
CHANNEL
L = 1475mm
2
281AR
CHANNEL
L = 1496.5mm
CHANNEL
L = 1475mm
166L
2
167L
CHANNEL
L = 1475mm
2
281AL
CHANNEL
L = 1496.5mm
CSJ
6
THESE COMPONENTS
ARE TO BE
JOINED
TO THESE COMPONENTS
CHANNEL JOINER
L= 200mm (7.9")
![Page 5: Absco Aviary Assembly Instructions Model: A15301FKabscosheds.com.au/pdf/Instructions/A15301FK_(J).pdf · notched corners to bottom of sheets lay these sections over the panel as shown,](https://reader036.fdocuments.in/reader036/viewer/2022081607/5ed6ae0739f16f294d5743f9/html5/thumbnails/5.jpg)
20mm
15mm
QTY = 10pcs.
CHANNEL
(0.79")
(0.59")
PU
SH
PU
SH
CHANNEL
CSJ
PAGE 5
INSTRUCTIONS FOR JOINING SPLICED CHANNELS
CSJ
CSJ
HIGH-SIDE
C
H
A
N
N
E
L
LOW-SIDE
C
H
A
N
N
E
L
C
S
J
C
S
J
C
S
J
= =
= =
==
=
=
STEP 1. Position the channels and the CSJ
joiner channel so the center of the
CSJ is in line with the end of each
channel to be joined together.
STEP 2. Join the first channel to the CSJ by inserting the center
of the CSJ (on an angle) to the end of the channel
where the JOIN>> text is marked. Push down one side
of the CSJ until you hear a 'click'.
STEP 3. Join the second channel to the CSJ
by positioning the <<JOIN end of the
channel at the center of the CSJ
(on an angle). Push the CSJ into
the channel until you here a 'click'.
=
The joined channels should now
look like the picture above with the
CSJ positioned equally inside of the
joined channels.
FINISHED CHANNEL
=
NOTE: THE TEXT MARKED ON ALL PARTS MUST BE SHOWN ON THE SAME SIDE AS EACH OTHER.
JOIN>> <<JOIN
JOIN>>
JOIN>>
SJ
JOIN>>
<
<
J
O
I
N
JOIN>> <<JOIN
J
CSJ
DRILL 4mm (0.16") x 3mm (0.12")
(2 PER A SIDE) HOLES TO
SECURE SECTIONS TOGETHER.
(THESE SCREWS MAY HAVE TO
BE TEMPORARILY REMOVED
AND REPLACED DURING LATER
ASSEMBLY)
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: A15301FK 28/04/16
Absco Aviary Model: A15301FK
![Page 6: Absco Aviary Assembly Instructions Model: A15301FKabscosheds.com.au/pdf/Instructions/A15301FK_(J).pdf · notched corners to bottom of sheets lay these sections over the panel as shown,](https://reader036.fdocuments.in/reader036/viewer/2022081607/5ed6ae0739f16f294d5743f9/html5/thumbnails/6.jpg)
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: A15301FK 28/04/16
Absco Aviary Model: A15301FK
PAGE 6
=
=
=
2
9
9
3
m
m
(
1
1
7
.
8
"
)
STEP 1. PRE-ASSEMBLY OF SPLICED CHANNELS
2 x 81A
2 x 166
2 x 167
NOTE: JOIN TOGETHER 12 X CHANNEL SECTIONS USING 6 X CHANNEL JOINERS (PART CSJ)
1
6
7
R
1
6
7
L
1
6
6
L
1
6
6
R
8
1
A
L
8
1
A
R
2 X 81AR
2 X 81AL
1 X 166R
1 X 166L
1 X 167R
1 X 167L
NOTE: SOME CHANNELS HAVE
HOLES IN THEM - YOU WILL NEED
TO RE-DRILL HOLES ON ANY
CHANNEL WHERE THE CSJ
JOINING CHANNEL COVERS
HOLES ON THE CHANNELS
YOU ARE CONNECTING
2
9
5
0
m
m
(
1
1
6
.
2
"
)
![Page 7: Absco Aviary Assembly Instructions Model: A15301FKabscosheds.com.au/pdf/Instructions/A15301FK_(J).pdf · notched corners to bottom of sheets lay these sections over the panel as shown,](https://reader036.fdocuments.in/reader036/viewer/2022081607/5ed6ae0739f16f294d5743f9/html5/thumbnails/7.jpg)
VIE
W O
F R
OO
F C
OM
PO
NE
NT
S
NO.
P
AG
E 7
AB
SC
O IN
DU
ST
RIE
S
AS
SE
MB
LY
IN
ST
RU
CT
IO
N - M
OD
EL
: 1
53
01
FK
2
8/0
4/1
6
Abs
co E
cono
my
She
d M
odel
: A15
031F
K
88
A
43
A
43
A
43
A
43
A
81
A
81
A
88
A
![Page 8: Absco Aviary Assembly Instructions Model: A15301FKabscosheds.com.au/pdf/Instructions/A15301FK_(J).pdf · notched corners to bottom of sheets lay these sections over the panel as shown,](https://reader036.fdocuments.in/reader036/viewer/2022081607/5ed6ae0739f16f294d5743f9/html5/thumbnails/8.jpg)
VIE
W O
F W
ALL
CO
MP
ON
EN
TS
P
AG
E 8
AB
SC
O IN
DU
ST
RIE
S
AS
SE
MB
LY
IN
ST
RU
CT
IO
N - M
OD
EL
: A
15
30
1F
K 2
8/0
4/1
6
Abs
co A
viar
y M
odel
:A
1530
1FK
FR
ON
T
DO
OR
15
4R
15
4
15
4
33
A
30
A
30
A
30
A
30
A
33
A
15
4
15
4L
81
F
16
6
16
7
19
1
19
1
17
2
16
4
19
1
18
1
19
1
16
4
18
1
19
2
16
7
18
1
18
1
17
2
19
1
18
1
19
1
81
F
16
6
SID
E P
AN
EL
SID
E P
AN
EL
19
1
18
1
19
1
18
1
19
5
LE
FT
H
AN
D
RIG
HT
H
AN
D
![Page 9: Absco Aviary Assembly Instructions Model: A15301FKabscosheds.com.au/pdf/Instructions/A15301FK_(J).pdf · notched corners to bottom of sheets lay these sections over the panel as shown,](https://reader036.fdocuments.in/reader036/viewer/2022081607/5ed6ae0739f16f294d5743f9/html5/thumbnails/9.jpg)
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: A15301FK 28/04/16
Absco Aviary Model: A15301FK
ABSCO ASSEMBLY INTRODUCTION
FASTENING SYMBOLS
The snap-tite assembly system locks most perimeter channels to all roof and wall sheets
without the need for tools and fasteners. Where possible, many components
have been pre-punched for ease of assembly, with others requiring 3mm holes to
be drilled where required.
To pre-assemble the four wall panels
and two roof panels, the perimeter
channels are secured to the top and
bottom of each panel using the
snaptite system, as detailed on the
following pages wherever you see
the symbol.
Position sheets on timbers,
trestles or partly over edge of
concrete slab.
Each perimeter channel must finish flush
with the edges of the sheets. the snap-tite
system allows adjustment for this
process by simply tapping the channel
along the sheets until each end is neatly
flush.
Join components together with one screw at this
location only, as some channel sections have extra
holes that are not required for this model of garden
shed
Do not join components together at this location yet,
as the screw may obstruct further assembly of other
components
3mm POP RIVETS (SMALL
FLANGE FOR FITTING
DOOR HINGES)
PUSH
PUSH
HIG
H S
ID
E
HIG
H S
ID
E
PU
SH
H
IG
H
S
ID
E
HIG
H S
ID
E
After joining sheets together,
position channel over one end of the
sheets, gently tapping it over the
snaptite lugs, working along the
sheets to the other end.
H
I
G
H
S
I
D
E
S
N
A
P
T
T
E
i
S
N
A
P
T
T
E
i
SNAP
T TE
i
3mm POP RIVETS (LARGE
FLANGE FOR FITTING
MESH TO FRAMES)
Pre-drill the hole prior to joining components together.
Many components will be able to be used as a template
to determine drilling locations
D
PAGE 9
![Page 10: Absco Aviary Assembly Instructions Model: A15301FKabscosheds.com.au/pdf/Instructions/A15301FK_(J).pdf · notched corners to bottom of sheets lay these sections over the panel as shown,](https://reader036.fdocuments.in/reader036/viewer/2022081607/5ed6ae0739f16f294d5743f9/html5/thumbnails/10.jpg)
REAR PANEL ASSEMBLY
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: A15301FK 28/04/16
Absco Aviary Model: A15301FK
30A
30A
S
N
A
P
T
T
E
i
81F
S
N
A
P
T
T
E
i
81F
PAGE 10
![Page 11: Absco Aviary Assembly Instructions Model: A15301FKabscosheds.com.au/pdf/Instructions/A15301FK_(J).pdf · notched corners to bottom of sheets lay these sections over the panel as shown,](https://reader036.fdocuments.in/reader036/viewer/2022081607/5ed6ae0739f16f294d5743f9/html5/thumbnails/11.jpg)
PAGE 11
ROOF PANEL ASSEMBLY
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: A15301FK 28/04/16
Absco Aviary Model: A15301FK
S
N
A
P
T
T
E
i
S
N
A
P
T
T
E
i
43A
43A
43A
81A
88A
81A
88A
43A
![Page 12: Absco Aviary Assembly Instructions Model: A15301FKabscosheds.com.au/pdf/Instructions/A15301FK_(J).pdf · notched corners to bottom of sheets lay these sections over the panel as shown,](https://reader036.fdocuments.in/reader036/viewer/2022081607/5ed6ae0739f16f294d5743f9/html5/thumbnails/12.jpg)
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: A15301FK 28/04/16
Absco Aviary Model: A15301FK
SIDE PANEL ASSEMBLY
LEFT HAND SIDE
PAGE 12
STEP I.
STEP 3.
STEP 2.
S
M
A
L
L
E
D
G
E
JOIN THE JAMB AND CHANNEL SECTIONS
(191 & 172) TOGETHER AT PRE-PUNCHED
LOCATIONS TO FORM THE CORNER
MULLION. THE CHANNEL SECTION WILL
FINISH 20mm SHORT OF THE JAMB AT
EACH END.
JOIN TWO JAMB SECTIONS (191)
TOGETHER TO FORM ONE
DOUBLE JAMB.
JOIN TWO SHEETS TOGETHER
AS SHOWN
STEP 2. STEP 1.
30A
33A
154
154
30A
33A
167
181
191
172
166
191
181
191
191
SMALL PAN
THIS SIDE
![Page 13: Absco Aviary Assembly Instructions Model: A15301FKabscosheds.com.au/pdf/Instructions/A15301FK_(J).pdf · notched corners to bottom of sheets lay these sections over the panel as shown,](https://reader036.fdocuments.in/reader036/viewer/2022081607/5ed6ae0739f16f294d5743f9/html5/thumbnails/13.jpg)
PAGE 13ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: A15301FK 28/04/16
Absco Aviary Model: A15301FK
SIDE PANEL ASSEMBLY LEFT HAND SIDE (CONTINUED)
STEP 4.FIT THE TOP AND BOTTOM CHANNELS (166 & 167) TO THE WALL
SHEETS. ENSURE THAT THE PRE-PUNCHED HOLES IN THE CHANNEL
SIDE ARE LOCATED AT THE RIGHT HAND END FOR CONNECTING
THE JAMBS AND CORNER MULLION. THE CHANNELS WILL EXTEND
PAST THE CORNER MULLION BY 3mm.
CORNER MULLION
(STEP 1)
DOUBLE JAMB
(STEP 2)
SMALL PAN
THIS SIDE
SHEETS
(STEP 3)
S
N
A
P
T
T
E
i
S
N
A
P
T
T
E
i
166
167
191
![Page 14: Absco Aviary Assembly Instructions Model: A15301FKabscosheds.com.au/pdf/Instructions/A15301FK_(J).pdf · notched corners to bottom of sheets lay these sections over the panel as shown,](https://reader036.fdocuments.in/reader036/viewer/2022081607/5ed6ae0739f16f294d5743f9/html5/thumbnails/14.jpg)
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: A15301FK 28/04/16
Absco Aviary Model: A15301FK
SIDE PANEL ASSEMBLY
STEP 5.NOTCHED CORNERS TO
BOTTOM OF SHEETS
LAY THESE SECTIONS OVER THE PANEL
AS SHOWN, LOCKING THE SHEETS INTO
THE BOTTOM CHANNEL.
MOVE THE TOP INFILL CHANNELS
(181) INTO POSITION.
S
N
A
P
T
T
E
i
S
N
A
P
T
T
E
i
S
N
A
P
T
T
E
i
S
N
A
P
T
T
E
i
154
154
181
181
181
LEFT HAND SIDE (CONTINUED)
PAGE 14
D
D
D
D
D
D
D
D
D
D
D
D
![Page 15: Absco Aviary Assembly Instructions Model: A15301FKabscosheds.com.au/pdf/Instructions/A15301FK_(J).pdf · notched corners to bottom of sheets lay these sections over the panel as shown,](https://reader036.fdocuments.in/reader036/viewer/2022081607/5ed6ae0739f16f294d5743f9/html5/thumbnails/15.jpg)
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: A15301FK 28/04/16
Absco Aviary Model: A15301FK
SIDE PANEL ASSEMBLY
RIGHT HAND SIDE
PAGE 15
STEP I.
STEP 3.
STEP 2.
JOIN THE JAMB AND CHANNEL SECTIONS
(191 & 172) TOGETHER AT PRE-PUNCHED
LOCATIONS TO FORM THE CORNER MULLION.
THE CHANNEL SECTION WILL FINISH 20mm
SHORT OF THE JAMB AT EACH END.
JOIN TWO JAMB SECTIONS (191) TOGETHER
TO FORM ONE DOUBLE JAMB.
JOIN THE TWO SHEETS
TOGETHER AS SHOWN
154L
154
33A
30A
166
167
172
191
181
191
191
181
33A
30A
SMALL PAN
THIS SIDE
STEP 1. STEP 2.
![Page 16: Absco Aviary Assembly Instructions Model: A15301FKabscosheds.com.au/pdf/Instructions/A15301FK_(J).pdf · notched corners to bottom of sheets lay these sections over the panel as shown,](https://reader036.fdocuments.in/reader036/viewer/2022081607/5ed6ae0739f16f294d5743f9/html5/thumbnails/16.jpg)
PAGE 16
STEP 4.FIT THE TOP AND BOTTOM CHANNELS (166 & 167 TO THE
WALL SHEETS. ENSURE THAT THE PRE-PUNCHED HOLES IN
THE CHANNEL SIDE ARE LOCATED AT THE LEFT HAND END
FOR CONNECTING THE JAMBS AND CORNER MULLION.
THE CHANNELS WILL EXTEND PAST THE CORNER MULLION
BY 3mm.
CORNER MULLION
(STEP 1)
DOUBLE JAMB
(STEP 2)
SHEETS
(STEP 3)
SMALL PAN
THIS SIDE
S
N
A
P
T
T
E
i
S
N
A
P
T
T
E
i
167
191
166
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: A15301FK 28/04/16
Absco Aviary Model: A15301FK
SIDE PANEL ASSEMBLY
RIGHT HAND SIDE (CONTINUED)
![Page 17: Absco Aviary Assembly Instructions Model: A15301FKabscosheds.com.au/pdf/Instructions/A15301FK_(J).pdf · notched corners to bottom of sheets lay these sections over the panel as shown,](https://reader036.fdocuments.in/reader036/viewer/2022081607/5ed6ae0739f16f294d5743f9/html5/thumbnails/17.jpg)
PAGE 17ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: A15301FK 28/04/16
Absco Aviary Model: A15301FK
SIDE PANEL ASSEMBLY RIGHT HAND SIDE (CONTINUED)
STEP 5.
NOTE: THIS EDGE
ONLY FOLDED AT 90
DEGREES (154L)
NOTCHED CORNERS TO
BOTTOM OF SHEETS
LAY THESE SECTIONS OVER THE
PANEL AS SHOWN, LOCKING THE
SHEETS INTO THE BOTTOM CHANNEL.
MOVE THE TOP INFILL CHANNELS
(181) INTO POSITION.
S
N
A
P
T
T
E
i
S
N
A
P
T
T
E
i
S
N
A
P
T
T
E
i
S
N
A
P
T
T
E
i
154L
30A
181
181
181
D
D
D
D
D
D
D
D
D
D
D
D
![Page 18: Absco Aviary Assembly Instructions Model: A15301FKabscosheds.com.au/pdf/Instructions/A15301FK_(J).pdf · notched corners to bottom of sheets lay these sections over the panel as shown,](https://reader036.fdocuments.in/reader036/viewer/2022081607/5ed6ae0739f16f294d5743f9/html5/thumbnails/18.jpg)
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: A15301FK 28/04/16
Absco Aviary Model: A15301FK
FRONT PANEL ASSEMBLY
STEP 1.
STEP 2.
8
m
m
JOIN ALL SECTIONS TOGETHER, LINING UP
EACH JAMB WITH PRE-PUNCHED HOLES
LOCATED IN BOTH CHANNEL SECTIONS.
PARTS REQUIRED:
2) CHANNELS (PART 164)
3) JAMBS (PART 191)
191
191
164
191
164
PAGE 18
![Page 19: Absco Aviary Assembly Instructions Model: A15301FKabscosheds.com.au/pdf/Instructions/A15301FK_(J).pdf · notched corners to bottom of sheets lay these sections over the panel as shown,](https://reader036.fdocuments.in/reader036/viewer/2022081607/5ed6ae0739f16f294d5743f9/html5/thumbnails/19.jpg)
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: A15301FK 28/04/16
Absco Aviary Model: A15301FK
FRONT PANEL ASSEMBLY (CONTINUED)
STEP 3.
STEP 6.
STEP 5.
STEP 4.
THIS EDGE ONLY
FOLDED AT 90
DEGREES.
LAY THESE SECTIONS, ONE AT A TIME,
OVER THE FRAME AS SHOWN, LOCKING
THE SHEETS INTO THE BOTTOM
CHANNEL.
LOCK THE CHANNEL ON TO THE
SHEET AS SHOWN. THE CHANNEL
WILL FINISH 30mm IN FROM EACH
SIDE OF THE SHEET.
MOVE THE DOOR HINGE JAMB (PART 192) INTO
POSITION, LOCATING IT "OVER THE TOP" OF THE
SHEET (154R) AND SECURING IT TO THE OTHER JAMB
(191). (THE SCREWS SECURING THE EXISTING JAMB
(191) WILL HAVE TO BE REMOVED AND THEN
REPLACED)
MOVE THE THREE INFILL CHANNELS INTO
POSITION AND SCREW TO THE TOP/BOTTOM
CHANNELS WITH TWO SCREWS EACH.
S
N
A
P
T
T
E
i
S
N
A
P
T
T
E
i
N
O
T
C
H
E
D
C
O
R
N
E
R
S
T
O
B
O
T
T
O
M
O
F
S
H
E
E
T
S
154R
192
181
181 181
PAGE 19
181
D
D
D
D
D
D
D
D
D
D
D
![Page 20: Absco Aviary Assembly Instructions Model: A15301FKabscosheds.com.au/pdf/Instructions/A15301FK_(J).pdf · notched corners to bottom of sheets lay these sections over the panel as shown,](https://reader036.fdocuments.in/reader036/viewer/2022081607/5ed6ae0739f16f294d5743f9/html5/thumbnails/20.jpg)
PAGE 20ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: A15301FK 28/04/16
Absco Aviary Model: A15301FK
FRONT PANEL ASSEMBLY (CONTINUED)
STEP 7.
STEP 8.
FIT THE MIDRAIL PARALLEL ABOVE THE
DOOR, TO THE SIDE JAMBS WITH SCREWS
FROM THE UNDERNEATH SIDE.
FOR THE MIDRAIL ABOVE THE DOOR,
JOIN THE JAMB (195) TO THE
CHANNEL (181) AS SHOWN.
LAY THE DOOR PANEL IN THE
OPEN POSITION ON THE FRAME
AS SHOWN. USING THE SMALL
FLANGE POP RIVETS,
SECURE THE DOOR
TO THE DOOR
HINGE JAMB.
195
181
D
![Page 21: Absco Aviary Assembly Instructions Model: A15301FKabscosheds.com.au/pdf/Instructions/A15301FK_(J).pdf · notched corners to bottom of sheets lay these sections over the panel as shown,](https://reader036.fdocuments.in/reader036/viewer/2022081607/5ed6ae0739f16f294d5743f9/html5/thumbnails/21.jpg)
PAGE 21
SCREW THE FRONT FRAME CORNER
JAMBS INTO THE PRE-PUNCHED
HOLES OF THE SIDE WALL CORNER
MULLIONS.
SIDE WALL PANEL CHANNELS FIT
INTO THE NOTCHED FRONT AND
REAR WALL PANEL CHANNELS
LAP THESE CORNER
SHEETS, DRILL AND
SCREW TOGETHER.
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: A15301FK 28/04/16
Absco Aviary Model: A15301FK
WALL PANEL ASSEMBLY
![Page 22: Absco Aviary Assembly Instructions Model: A15301FKabscosheds.com.au/pdf/Instructions/A15301FK_(J).pdf · notched corners to bottom of sheets lay these sections over the panel as shown,](https://reader036.fdocuments.in/reader036/viewer/2022081607/5ed6ae0739f16f294d5743f9/html5/thumbnails/22.jpg)
FINAL CONSTRUCTION
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: A15301FK 28/04/16
Absco Aviary Model: A15301FK
DYNABOLT
BOLT & NUT
STEELANGLE
SLAB
WALLSHEET
- EACH ANCHOR CONSISTS OF ONE NUT, BOLT,
DYNABOLT AND STEEL ANGLE
- DRILL A 10mm HOLE INTO THE WALL SHEET
- DRILL A 10mm HOLE INTO THE CONCRETE
STEP 1.
STEP 2.
STEP 3.
THE ROOF PANEL WILL OVERLAP THE
FRONT AND SIDE WALLS BY 37mm
THERE IS NO OVERHANG OVER THE
BACK WALL
LINE UP THE PRE-PUNCHED HOLES IN
BOTH THE ROOF SHEETS AND SIDE
WALL TOP CHANNELS, AND SECURE
WITH SCREWS, COMMENCING WITH
ONE SCREW IN EACH CORNER FIRST.
DRILL THROUGH THE SIDE OF THE
BACK WALL LIP FLASHING INTO THE
BACK WALL TOP CHANNEL AND
SECURE WITH SCREWS.
DRILL THROUGH THE FRONT
SHEET INTO THE FRONT
WALL TOP CHANNEL AND
SECURE WITH SCREWS
ANCHORING OF SHED
LOCATION OF 12
CONCRETE ANCHORS
PAGE 22
![Page 23: Absco Aviary Assembly Instructions Model: A15301FKabscosheds.com.au/pdf/Instructions/A15301FK_(J).pdf · notched corners to bottom of sheets lay these sections over the panel as shown,](https://reader036.fdocuments.in/reader036/viewer/2022081607/5ed6ae0739f16f294d5743f9/html5/thumbnails/23.jpg)
WARNING
INSIDE VIEW
OF AVIARY
IT IS RECOMMENDED THAT NEW
GALVINESED MESH SHOULD BE
WEATHERED FOR TWO (2) MONTHS
OR SCRUBBED WITH A MILD ACIDIC
SOLUTION SUCH AS VINEGAR, THEN
RINSED WITH WATER BEFORE
BEING USED IN BIRD HOUSING
APPLIANCES.
ALL MESH SHEETS ARE FITTED TO THE
OF THE AVIARY. INSIDE
THE MESH SHEETS ARE FIXED TO
FRAMEWORK USING THE LARGE FLANGE
RIVETS SUPPLIED.
WORKING FROM INSIDE THE AVIARY,
LOCATE THE FIRST MESH SHEET OVER
THE FRAMEWORK. DRILL 3mm HOLES
AND FASTEN WITH RIVETS TO THE
FRAMEWORK AT 150mm CENTRES.
IT IS IMPORTANT TO CONTINUALLY
STRETCH THE MESH TO ENSURE A
SMOOTH TIGHT FINISH.
LOCATE RIVETS AT THE INSIDE
INTERSECTION OF THE WIRE TO
FACILITATE TIGHTENING OF THE MESH
AS SHOWN.
FITTING OF WIRE MESH
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: A15301FK 28/04/16
Absco Aviary Model: A15301FK
PAGE 23
![Page 24: Absco Aviary Assembly Instructions Model: A15301FKabscosheds.com.au/pdf/Instructions/A15301FK_(J).pdf · notched corners to bottom of sheets lay these sections over the panel as shown,](https://reader036.fdocuments.in/reader036/viewer/2022081607/5ed6ae0739f16f294d5743f9/html5/thumbnails/24.jpg)
1 | P a g e
AUSTRALIA PRODUCT WARRANTY AGAINST DEFECTS
Congratulations on your purchase of an ABSCO SHED
ABSCO SHEDS, including garden sheds, garden beds, aviaries, storage units, garages, awnings and carports are made using high quality Australian made steel.
We are pleased to advise we warrant that the steel coating will not rust, crack, flake peel or blister for 20 years from date of purchase, when installed within Australia.
This warranty does not apply to surface deterioration of panels caused by ‘Swarf” (Tiny particles of steel debris left from cutting, grinding or drilling operations) that has not been removed after building construction, or as a result of contact with damp soil, chemicals, fertilisers or other corrosive substances.
This warranty covers any Absco product used for normal domestic use and installed in accordance with the installation instructions. The warranty does NOT cover Damage caused by storms, wind, rain snow or poor foundations. This warranty does NOT cover ABSCO products installed in severe coastal, industrial or other highly corrosive environments. The warranty does not cover fasteners (screws, nuts, bolts, rivets, hasps or bolts).
The warranty is limited to replacement and delivery of components and does not include any labour or installation costs. The benefits given by the warranty are in addition to your other rights and remedies under a law in relation to the goods or services to which the warranty relates.
The warranty applies to the exclusion of all other representations, guarantees or warranties express or implied, our goods come with guarantees that cannot be excluded under the Australian consumer law and is not transferable. You are entitled to a replacement or refund for a major failure and for compensation for any other foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of an acceptable quality and the failure does not amount to a major failure. For further information go to http://www.consumerlaw.gov.au.
Please retain a proof of purchase (sales docket or invoice) or register your warranty within 30 days of purchase here: www.absco.com.au/register_warranty.php
In the unlikely event a warranty claim is made, it must be supported by photographic evidence and details of the defect, including component part numbers, together with proof of purchase documentation (or on-line registration of purchase) and forwarded to the address below. Upon receipt of the warranty claim, the Customer Service Manager will contact you within three business days to advise you of the assessment outcome of the claim, which may include your expenses incurred in making the claim.
THE CUSTOMER SERVICE MANAGER, ABSCO INDUSTRIES, PO BOX 119 ACACIA RIDGE QLD AUSTRALIA 4110
PHONE: 1800 029701 FAX: 07-33441191 EMAIL: [email protected]
Issued 01 January 2012
![Page 25: Absco Aviary Assembly Instructions Model: A15301FKabscosheds.com.au/pdf/Instructions/A15301FK_(J).pdf · notched corners to bottom of sheets lay these sections over the panel as shown,](https://reader036.fdocuments.in/reader036/viewer/2022081607/5ed6ae0739f16f294d5743f9/html5/thumbnails/25.jpg)
2 | P a g e
ABSCO SHEDS - STORAGE GUIDELINES
ABSCO SHEDS include garden sheds, garden beds, storage units, aviaries, garages, awnings and carports. ABSCO SHEDS are designed to be weatherproof for normal weather conditions. In the event of extreme weather conditions such as heavy rain, combined with high wind gusts, the ridge capping, sheeting joins, screw fixings etc., may exhibit minor deformations which may allow some water entry. These areas should be checked regularly to ensure that maximum strength and protection is maintained. Other weather conditions such as extreme heat and extreme cold, moist or dry air can influence the effects of concrete floor moisture and/or condensation on the underside of the roof sheets. ABSCO SHEDS and storage units are primarily used for storage of garden equipment such as lawnmowers, wheelbarrows, garden tools etc. Storage items that might be adversely affected by any of the above conditions may require additional protection such as being sealed or covered by plastic sheets and/or stacked above the concrete floor on timber slats. Waterproof sealants may be used to offer further protection where required around joins and screw fixings, as can rubber door seals and other products which are available from most hardware outlets. Placement of waterproof sealants (silicone) between the base of the shed and concrete slab is not recommended, as this process can have a reverse effect, preventing excess water from escaping, resulting with water accumulating and being trapped inside the shed. Absco accepts no responsibility for water entry, floor moisture, condensation or the condition of the Contents inside your Absco steel building arising from any of the pre-mentioned weather conditions.