Abrasive Blasting Works at Wtf – 3 Construction Site 2018
4
JOB SAFETY ANALYSIS PCD PROJECT: WATER TREATMENT FACILITIES – 3 FACILITY/PLANT LOCATION: WTF-3 PJ DESCRIPTION OF WORK: ABRASIVE BLASTING WORKS AT WTF – 3 CONSTRUCTION SITE CONTRACTOR: JGULF Int’l. Co. Ltd. REVISION: 0 JSA No.: MACE - 2018 JSA PARTICIPANTS: Aldrin C. Alcantara Ghassan D. Matta (Sub-contractor HSE / Construction Manager) APPROVED BY: Jose N. Banugan (Contractor HSE Manager/Engineer) M.S. No.: REVIEWED BY: Andres C. Moreno (PCD Safety Engineer) DATE: DATE: DATE: S.NO. STEPS REQUIRED TO COMPLETE TASK IDENTIFY HAZARDS & ASSESS RISK CONTROLS TO ELIMINATE/REDUCE RISK 1. Planning/Site preparation Unauthorized work. Conflicting activities. Invalid permit. Lack of competency. Lack or poor communication. Haste or shortcut. Obtain PTW prior to the commencement of the work and 1 st copy to be kept at the worksite in compliance to KJO work permit procedure. Make sure that there are no conflicting activities near the worksite before starting the job Get the permit validated for the specific day. Supervisor must ensure that all work activities are carried out by competent personnel. Conduct Toolbox meeting, review the Method statement and Job safety analysis to all craftsmen involved in the work activities. Responsible person will conduct inspection, monitor the work 1 of 3
description
Nice sample
Transcript of Abrasive Blasting Works at Wtf – 3 Construction Site 2018
Al-Khafji Joint Operations
JOB SAFETY ANALYSIS
pcd PROJECT: Water treatment facilities 3
Facility/Plant Location:
WTF-3 PJdescription of work:
ABRASIVE BLASTING WORKS AT WTF 3 CONSTRUCTION SITEcontractor:JGULF Intl. Co. Ltd.REVISION: 0
JSA No.: MACE - 2018
JSA PARTICIPANTS:
Aldrin C. Alcantara Ghassan D. Matta(Sub-contractor HSE / Construction Manager)APPROVED BY:
Jose N. Banugan (Contractor HSE Manager/Engineer)M.S. No.:
REVIEWED BY:
Andres C. Moreno(PCD Safety Engineer)
DATE:DATE:DATE:
S.No.Steps Required to Complete TaskIdentify Hazards & Assess RiskControls to Eliminate/Reduce Risk
1.Planning/Site preparation Unauthorized work. Conflicting activities. Invalid permit. Lack of competency. Lack or poor communication. Haste or shortcut.
Obtain PTW prior to the commencement of the work and 1st copy to be kept at the worksite in compliance to KJO work permit procedure.
Make sure that there are no conflicting activities near the worksite before starting the job
Get the permit validated for the specific day.
Supervisor must ensure that all work activities are carried out by competent personnel.
Conduct Toolbox meeting, review the Method statement and Job safety analysis to all craftsmen involved in the work activities.
Responsible person will conduct inspection, monitor the work activities and have to ensure safety standards and procedures are strictly adhered to.
2.Blasting in Operation.(Including air blowing/cleaning) Insufficient air for breathing. Air contaminated. (Breathing problem). Improper supply of air.
Ineffective filters. Garnet blasting on body part/ Body injury locking of dead mans device for intermediate inspection. Exposure of dust, noise and injury to workers.
Fire explosion. Use regulator to control supply
Change filter at the advised frequency.
Monitoring the air and ensure good quality of air. Ensure dead mans device is always in good operating condition.
Do not allow workers to play with the sand blasting machine. Make sure sand blasting is done only by trained personnel. Barricade the area to prevent unauthorized entry. Ensure workers involved in blasting are wearing appropriate PPEs.
Ensure Danger Abrasive Blasting in Progress Keep Away and Noise Hazard are posted in the area.
Ensure the blast gun is fitted with Emergency Release Handle (Dead Mans Handle) and it is functional.
Do not left the blasting machine unattended with air supply on. Never allow any spray painting at the location when blasting is in progress. Dedicated Fire watch man shall be posted while blasting is on progress.
3.Changing the position to cover other area. Sand blasting on body part (body injury). Trip/fall Machine remain ON
Locking of dead mans device. Put OFF machine first.
Always keep the dead mans device in good operating condition.
After work completion of work make sure all the equipment & tool are properly taken back to their storage area.
4.Housekeeping. Scattered Materials. Arrange the recovery and safe disposal of spent garnet. Ensure of proper wind up of equipment, tools, and tidiness of the work area.
Required Training.: Safety Orientation; Manual Handling; Hand and Power Tools; Hot Works, Fire Protection and Prevention; Fire Watch Training; JSA and Risk Assessment; Crane and Rigging; Electrical Safety.
REQUIRED SAFETY EQUIPMENT
Hard Hats Yes Other GlovesYesFace ShieldYesHand Tools & Power ToolsYesCranesNo
Safety GlassYesWork VestYesGogglesYesCompactorNoForkliftNo
Steel Toe BootsYesSafety HarnessNoBarricadesYesLifting GearNoJackhammerNo
Leather GlovesYesSelf Retracting Lifeline (SRL)NoFire ExtinguihsersYesAir Hoist/CompresorYesOther Equipments/MaterialsYes
1 of 3
