National: Average turnover: 17-19% Average vacancy: 8% Training Success rate:
A86 Turnover Training Guide
Transcript of A86 Turnover Training Guide
-
7/26/2019 A86 Turnover Training Guide
1/36
1
CONFIDENTIAL & PROPRIETARY
Limited Distribution to Authorized Persons Only
Copyright 2010 Clearwire Corporation.
All Rights Reserved.
Auction 86Clearwire
Turnover Training
-
7/26/2019 A86 Turnover Training Guide
2/36
ITEM: Clearwire - Site Data Report - Example
REF NO: DATE: 1 of 1 PAGES: REV:
RF
(antenna info)
-
7/26/2019 A86 Turnover Training Guide
3/36
Red (301-060 degrees)
Blue (061-180 degrees)
Yellow (181-300 degrees)
RF Labeling
-
7/26/2019 A86 Turnover Training Guide
4/36
Zip Ties Coax
Stainless Steel only
Grounding
UV rated and weather resistant plastic tie wraps
only
Fiber
No tie wraps allowed
-
7/26/2019 A86 Turnover Training Guide
5/36
MPLSFOLDER
-
7/26/2019 A86 Turnover Training Guide
6/36
SITE ID T1 Delivered (#)
-
7/26/2019 A86 Turnover Training Guide
7/36
SITE ID POTS (#)
-
7/26/2019 A86 Turnover Training Guide
8/36
SITE ID Cabinet Installation (#)
-
7/26/2019 A86 Turnover Training Guide
9/36
SITE ID Cabinet Installation (#)
-
7/26/2019 A86 Turnover Training Guide
10/36
SITE ID Breaker (#)
-
7/26/2019 A86 Turnover Training Guide
11/36
SITE ID Meter (#)
-
7/26/2019 A86 Turnover Training Guide
12/36
Tower
BottomGrounding
-
7/26/2019 A86 Turnover Training Guide
13/36
SITE ID Tower Bottom Grounding (#)
1. 8 of extra power (neatly coiled)
2. 10 of extra fiber (neatly coiled)
-
7/26/2019 A86 Turnover Training Guide
14/36
RF
FOLDER
-
7/26/2019 A86 Turnover Training Guide
15/36
DIPSTICK
-
7/26/2019 A86 Turnover Training Guide
16/36
SITE ID - Dipstick
1. Need to show BOTH dipsticks for
each antenna.
2. E-Tilt MUST be visible
3. Check SDR (Site Data Report)
4. Recommendation: Take these shotson the ground
5. Label antenna with Sharpee
1. Site IDMN-MSPXXXX
2. Sector
-
7/26/2019 A86 Turnover Training Guide
17/36
17
DT/PLUMB
-
7/26/2019 A86 Turnover Training Guide
18/36
SITE ID - Antenna Downtilt - Sector X (#)
SITE ID - Antenna Plumb- Sector X (#)
1. There should be one for each sector
2. Tolerance level - .5
3. Label antenna with Sharpee
1. Site IDMN-MSPXXXX
2. Sector
1. There should be one for each sector
2. Tolerance level - .5
3. Label antenna with Sharpee
1. Site IDMN-MSPXXXX
2. Sector
*Do NOT need a shot of the pole for the antennathe
Plumb shot shown above will be suffice
-
7/26/2019 A86 Turnover Training Guide
19/36
19
BTS
Connections
-
7/26/2019 A86 Turnover Training Guide
20/36
SITE ID- BTS Connections(#)
1. Need a photo to show each antenna
to dap head connection
2. If the photo is blurry or one cannot
locate if the cables are connected
properly, the photo will be rejected
Must be able to see where the 1
stripe from the antenna goes to
the 1 stripe on the Dap Head
Must be able to see where the 2
stripe from the antenna goes to
the 2 stripe on the Dap Head
Must show proper snap ins to
eliminate movement due to
wind. Should have at least 2
points of support on jumper
-
7/26/2019 A86 Turnover Training Guide
21/36
SITE ID- BTS Connections(#)
Motorola Dap Head & Weatherproofing
1. Photo to show weaterproofing on each dap head and antenna
2. All connections properly weatherproofedshould not be able to see connector!3. Must be able to see color stripes to depict sector
4. Butyl and tape ONLY. No miracle tape
All connections on dap head must be
weatherproofed 50 ohm load must be weatherproofed
Miss ing buty l
NOT accepted
Poor mark ing
-
7/26/2019 A86 Turnover Training Guide
22/36
SITE ID- BTS Connections(#)
1. Need a photo to show each antenna
to dap head connection
2. If the photo is blurry or one cannot
locate if the cables are connected
properly, the photo will be rejected
Must be able to see where the 1
stripe from the antenna goes to
the 1 stripe on the Dap Head
Must be able to see where the 2
stripe from the antenna goes to
the 2 stripe on the Dap Head
Must show proper snap ins to
eliminate movement due to
wind. Should have at least 2
points of support on jumper
-
7/26/2019 A86 Turnover Training Guide
23/36
SITE ID- BTS Connections(#)
Huawei Dap Head & Weatherproofing
1. Photo to show weaterproofing on each dap head and antenna
2. All connections properly weatherproofedshould not be able to see connector!3. Must be able to see color stripes to depict sector
4. Butyl and tape ONLY. No miracle tape
All connections on dap head must be
weatherproofed 50 ohm load must be weatherproofed
Miss ing buty l
NOT accepted
Poor mark ing
-
7/26/2019 A86 Turnover Training Guide
24/36
SITE ID- BTS Connections(#)
Huawei Data Connection
1. Fiber Optic Cable connections. Standard isfor cable 1 to enter the lower of the two
connection points.
2. DC Power Cable:
2a. Blue = -48vDC
2b. Black = Return
3. DC Power Cable Shield Ground Point
NOTE: For cutting back the sheath on the
power cable please see the diagram on the
door.
-
7/26/2019 A86 Turnover Training Guide
25/36
SITE ID - BTS Connections(#)
Roxtex Installation and routing
1. Photo to show routing of unitstrut and roxtec for each sector
2. Should be able to see color coding to depict sector3. All cables should show good supportNo sharp bends
1. Show fiber coming out of roxtex
1. Show the inside of each junction box
Sector Identification
Snap Ins for support
-
7/26/2019 A86 Turnover Training Guide
26/36
26
RET
-
7/26/2019 A86 Turnover Training Guide
27/36
SITE ID - RET (#)
RET Installation
1. Photo to RET motors installed
2. All connections properly weatherproofedshould not be able to see connector!3. Must be able to see color stripes to depict sector
4. Butyl and tape ONLY. No miracle tape
1. All RET connections must be
weatherproofedthis would fail
-
7/26/2019 A86 Turnover Training Guide
28/36
SITE ID - RET (#)
RET Screenshots
1. Label photo with sector
2. Confirm downtilt value against SDR
Sector
-
7/26/2019 A86 Turnover Training Guide
29/36
29
Antenna
Spacing
-
7/26/2019 A86 Turnover Training Guide
30/36
SITE ID - Antenna Spacing (#)
1. Show 4 clearance between two antennas, e.g. sector a to sector b
Sector A Sector B
MN-MSP0015
-
7/26/2019 A86 Turnover Training Guide
31/36
31
Tape Drop
-
7/26/2019 A86 Turnover Training Guide
32/36
SITE IDRF Tape Drop
1. Label antenna with Sharpee
1. Site IDMN-MSPXXXX
2. Sector
3. Show Centerline
2. Check SDR (Site Data Report) for
correct height3. Tape drop to groundNOT top of
pole foundation
-
7/26/2019 A86 Turnover Training Guide
33/36
33
Serial Numbers
-
7/26/2019 A86 Turnover Training Guide
34/36
SITE IDRF Serial Number (#)
1. RF Serial #s needed
RET motors
Antennas
Dap Heads
2. Serial Numbers MUST be readable3. Recommendationtake these shots
on the ground
4. Label with Sharpee
SITE ID - Sector X
-
7/26/2019 A86 Turnover Training Guide
35/36
35
Sector
Identification
-
7/26/2019 A86 Turnover Training Guide
36/36
SITE ID- Sector Identification Sector X (#)
1. Show antenna with cables properly
marked
2. There should be no points where
jumpers rub
Must be able to see the jumpers are
properly supported