a1 c Gtechnical

8/13/2019 a1 c Gtechnical

1/13

CAM&

GROOVECOUPLIN

GS

FEDMIL/EN/DIN

A.1

A.1.1

CAM&GROOVECOUPLINGS FED MIL / EN / DIN

STANDARD

Federal Mil A-A-59326A

The sta nda rd for cam &g roove couplings w ere ba sed on the US Military

Specification Mil-C-27487. The Mil-C-27487 specified the casting method s,

materials, dimensions, tolerances, pressure ratings and inspection proce-

dures. In 1998, the origina l Mil-C-27487 specificat ion w as replaced by a new

Federa l Milita ry stan da rd: A-A-59326A. Fed era l Mil A-A-59326A guaran tees

interchange ab ility of couplings designed t o the sa me specification.

Interchangeabilitywith other brands

Between ma nufacturers cam &g roove couplings are interchang eable w ith

the except ion o f 1/2" (12.7 mm), 5" (127 mm) and 8" (203.2 mm). The A-A-

59326A Mil-specification d oes no t a pply to 1/2", 5" a nd 8" ca m &groove co u-

plings, due to the presence of two versions of cam &groove couplings in

tod ays market.

Limitations: Hose shanks with larger serrations are not designed to be

assembled w ith a ferrule or sleeve. Hose da mag e can result if they are

swa ged. The larger shank serrations will cut into the ho se resulting in leak-

ag e or permanent hose failure.

N.B.: Cam &groove couplings must never be used for steam or compressed air

applications.

EN 14420-7

The Europea n st an da rd EN 14420-7 wa s a pproved by CEN in Sept emb er

2004, and wa s applied to cam &groove couplings manufactured t o American

milita ry spe cificat ion MIL-C-27487 / A-A-59326A. This American sta nd ard

does not a pply to the connection side, but only to the coupling side. Other

parts like levers, bolts, rings and seals are not stand ardized.

Cam &g roove couplings prod uced to EN 14420-7 are interchang eab le with

those produced to the original MIL-C-27487 standard, but differ in terms of

hose tail design, thread , part number etc. A flat thread sea l has been a dd ed

to the female threaded parts, and a smooth hose shank complying with EN

14420-2 /DIN 2817 has b een a dd ed fo r assemb ly with RK safet y clamps

complying with EN 14420-3 /DIN 2817.

N.B.: Europea n sta ndard EN 14420-7 replaces DIN 2828 but does no t replace

MIL-C-27487 and Federal Mil A-A-59326A.

DIN 2828

Couplings produced to DIN 2828 are interchangeable with those produced

to the original MIL-C-27487 standard, but differ in terms of hose tail design,

thread, part number etc. A flat thread sea l has been ad ded to t he female

thread ed pa rts, and a smoo th ho se shank complying with DIN 2817 has been

ad ded for assembly with RK-safety clamps.


2/13

PRODUCTRANGE

OPERATION

To connect

1. Open the coupler by pulling back the locking lever above the cam hand les, whilst rotating the ha ndles

aw ay from the bod y of the coupler.

2. Insert the a daptor into the coupler

3. Close the coupler by rotating the cam ha ndles towa rds the body of the coupler. Locking occurs when

the ca m handles are closed . The coupler is properly closed w hen the locking levers on bot h the ca m

handles assemblies are flush. For extra security, insert safety clip throug h the ho les above the ca m

hand les. Line pressure, which moves t he coupler and ada ptor independ ently, increases the pressure

on t he cam face, ensuring increased locking leverage. Under normal conditions, safety locks are not

necessary, but a re recommend ed. The ad apt or and t he coupler are designed t o minimize the fluid

turbulence and the a brasion from dry products when connected.

To disconnect

4. Open the coupler by pulling b ack the locking lever above the cam hand les, whilst rotating the handles

aw ay from the bod y of the coupler.

5. Remove the adaptor from the coupler.

6. Close the coupler by rotating the cam ha ndles towards the bo dy of the coupler. Locking the coupler

when not in use will help protect it from accident al dama ge.

1. Stainless steel triang ular handles, pin, ring a nd safety pin are standard o n allmat erial versions. Handles manufactured by investment casting.

2. Holes for safety pin inserts

3. Earthing lug

4. Reinforced coupling section for increased mechanical strength

5. Long hose shank to ensure secure fixing

6. Marked with cam &groove type

7. Marked with diameter

8. Marked with standard compliance: MS (Military Specification) or DIN (Deutsche

Industrienorm)

9. Marked with ma terial identification: stainless steel, brass, bronze, aluminium,

polypropylene

10. Sea ls are available in NBR (standa rd), EPDM (for po lypropylene), PTFE, CSM,

FPM, FEP/Silicone, PTFE/EPDM and PTFE/FPM

11. Couplers are available in a safety monob lock version. Alternatively,

safety rebuilding set with pa tented safety hook can be used

12. Coupling insurance by b rand name LMC-Couplings

APPLICATIONCam &groo ve couplings are used for hose-to-hose or hose-to-pipe /manifold connections for the transfer of liquids or dry bulk products.

1

2

67

9

3 10 11 12

84

1

1

1

5

Chapt er A: Quick couplings


FEATURES

A.1.2


3/13

Chapt er A: Quick couplings

WORKING PRESSURE

TEMPERATURE RANGE

PRODUCTRANGE

MATERIAL

Coupling

LMC-Couplings cam &groove couplings are available in the following materials:

Stainless stee l

Brass

Bronze

Aluminium

Polypropylene


MATERIAL STANDARD DESCRIPTION CHEMICALCOMPOSITION

USA ASTM A 666 g ra de 316 Sta inless steel Cr: 16 - 18%, Ni: 10 - 14%, Mo : 2.0 - 3.0%,

German DIN 17 440 grade 1.4401 X5CrNiMo 17 10 2 C: less than 0.08%, Si: less than 1.0%,

UK BS970/4 grade 316S316 Mn: less than 2.0%, P: less than 0.045%,

France NF A35-579 grade Z6CND17.11 S: less than 0.03%, Fe: balance.

USA ASTM B584 g ra de C85700 co pper a llo y Cu: 58.09 - 64%, Sn: 0.50 - 1.50%, Pb : 0.80 -

German DIN 1709 grade CuZn37pb 1.50%, Zn: 32.0 - 40.0%, others: trace.

UK BS1400 grade DCB3

France NF A53-703 grade UZ40Y30

USA ASTM B584 g ra de C84400 co pper a llo y, Cu: 78.0 - 82.0%, Zn: 7.0 - 10.0%, Pb : 6.0 -

German DIN 1705, grade CuSn2ZnPb 8.0%, Sn: 2.0 - 3.5%, others: trace.

UK BS1400 grade LG1

USA ASTM B85 grade 380 Cu: 2.0 - 4.0%, Si: 7.5 - 9.5%, Mg: below

German DIN 1725 grade GD-AISI9Cu3 0.3%, Zn: below 1.0%, Fe: below 1.3%,

UK BS 1490 grade LM24 Mn: below 0.5%, Ni: below 0.5%,

Sn: below 0.3%; AI: balance.

LMC-Couplings polypropylene cam &groove couplings contain 25-30%fibreglass reinforcement.

Stainless steel

Brass

Bronze

Aluminium

Polypropylene

(Gun Meta l, 88-10-0-2, tin Bronze)

A.1.3

CAM&

GROOVECOUPLIN

GS

FEDMIL/EN/DIN

A.1

INCH 1/2" 3/4"-2" 2.1/2" 3" 4" 5" 6" 8"

Working pressure Bar Psi Bar Psi Bar Psi Bar Psi Bar Psi Bar Psi Bar Psi Bar Psi

Brass 11 150 18 250 11 150 9 125 7 100 5 75 5 75 - -

Bronze - - 18 250 11 150 9 125 7 100 - - - - - -

Aluminium 11 150 18 250 11 150 9 125 7 100 5 75 5 75 5 75

Stainless steel 11 150 18 250 16 225 14 200 7 100 7 100 7 100 3 50

8" aluminium with 4 handles

4" polypropylene with 3 handles

1/2 with 1 hand le for a ll materials

The w orking pressures shown ab ove refer to amb ient temperatures using elastomer seals. Higher tempe ratures and /or PTFE seals will

reduce the rat ed coup ling p ressure. In the ca se of polypropylene, the maximum wo rking temp erat ure is 70C /160F, at w hichtemperat ure the w orking pressures show n a bove sho uld be reduced by 40%.

- 20C /- 4F up to 70C /158F


4/13

Brass -

Bronze - -

Aluminium

Stainless steel

Polypropylene - - -

Production method

All sizes of b rass and bronze ca m &groove couplings are shell-moulded or sand cast.

The t ype o f aluminium is a sa nd cast 713-T5 alloy, which ca n be anod ised if required .

Stainless steel couplings are investment-cast in a range of common sizes and are electro-polished fo r clean applications. The sta inless steel

q uality fo r cam &groove coupling s is sta ndard AISI 316-EN 1.4401.

Polypropylene couplings are mad e from polypropylene reinforced with 25%-30%acid-resista nt fibreg lass.

Materials and sizes

A.1.4 Chapt er A: Quick couplings

INCH 1/2 3/4-2 2.1/2 3-4 5-6 8

ND 13 20-50 65 75-100 125-150 200

Available

- Not available

Material

Seal

Standard seal

The sta nda rd cam &groove seal consists of a sta nda rd squa re-section, availab le in:

Closed sea l

VLXPSG closed cam &groove seals are de signe d for extreme chemical app lications. These sea ls combine the best prope rties of tw o

different mat erials; the pressure set o f the rubb er core and the chemical resistance provided by t he FEP enca psulation. Encapsulation

of the Silicone core ensures improved o perationa l safety, when compared with a n open envelope seal. VLXPSG seals are produced

without the use of an imal derived ingred ients, ADI free. This reduces the risk of BSE prion cont aminat ion. VLXPSG closed

cam &groove sea ls resist high t emperature opera tion: from -60C /-76F up to 204C /400F.

Open envelope seal

The open envelope sea l consists of a U-section PTFE envelope and a sq uare-section EPDM core. The construction method used for the

open envelope seal ensures excellent compression properties. The PTFE envelope allow s the seal to withsta nd temperat ures of up t o

200C /390F.

NBR (standard for all materials, except polypropylene)

EPDM (standard for material polypropylene)

FPM

CSM

FEP envelope

EPDM core (standard)FPM core (on request)

PTFE envelope

EPDM core (standard)FPM core (on request)



5/13

A.1.5Chapt er A: Quick couplings

CAM&

GROOVECOUPLIN

GS

FEDMIL/EN/DIN

A.1

PTFE envelope

FPM core (standa rd)VMQ core (on request)

Closed envelope seal

The closed e nvelope sea l remove s all conta ct b etw een ch emicals and the se al core. The fully-closed PTFE envelope

complet ely encapsulates the FPM. The ma ximum temperature for this type is 200C /390F.

Thread sea l

Female threaded coupler and ad apt or components complying with EN 14420-7 /DIN 2828 stand ards con tain a thread

seal. Female thread ed ca m &groove co uplings a re sealed by screwing a male BSPT/BSP thread up t o the thread seal.

Threa d sea ls are available in: PTFE - PUR

Properties seals

NBR= Perbuna n is a registered tradem ark of Bayer AG / EPDM= Keltan is a registered trade mark of DSM / FPM= Viton is a registered tradema rk of DuPont Performan ce Elastom er

CSM= Hypalon is a registered t radema rk of DuPont Performance Elastom er / PTFE = Teflon is a registered tradema rk of DuPont Performan ce Elastom er

VMQ = Silplu s is a registered t rade ma rk of Gene ral Electric Co / TFMTMis a registered tradema rk of Dyneon.

PTFE or PUR

REF. ASTM POLYMER TRADENAME HARDNESS C F + PROPERTIES -

VLXB... NBR Acrylonitrile Buta diene Perbunan 60 + /- 5 -30C -22F Oil based hydraulic Ozone,

Shore A 120C 250F fluid, fats, animal and sunlight

vegetable oils, flame weather

retardan t, liq uids, grease,

wa ter and air

VLXE... EPDM Ethylene-propylene- Keltan 70 + /- 5 -40C -40F Acids, steam, alcohol Oil,

Diene Rubbe r Shore A 145C 290F greases

VLXV... FPM Fluorocarbon Viton 70 + /- 5 -30C -22F Mineral oils and greases, Steam

Shore A 200 C 390 F a lifa tic, a ro ma tic, a nd also

special chlorinated hydro-

carbons, petrol, diesel fuels,

silicon oils and greases

VLXH... CSM Chlorosylfonated Hypalon 70 + /- 5 -40 C -40 F Acids and oils, obsolescent Chlorine

polyethylene Shore A 140C 285F and ozone resistant

VLXPSG... FEP / Copolymer of Hexa-fluorpropylene / Teflon / 60 + /- 5 -60 C -76 F Resista nt to a lmo st a ll kinds Ha rd ness

VMQ Silicone Silicone Shore D 204 C 400 F o f chemica l pro ducts, stea m,

oils... Excellent self-lubricatingand anti adhesive properties

VLXP... PTFE / Poly tetrafluorethylene / Teflon / 85 + /-5 -25C -13F

EPDM Keltan Shore D 100C 212F

VLXP...V PTFE / Poly tetrafluorethylene / Teflon / 85 + /-5 -10C 14F

FPM Fluorocarbon Viton Shore D 200C 390F

VLXPG... PTFE/ Poly tetrafluorethylene / TFMTM/ 74 + /- 5 -15 C -26 F Acids and oils, obsolescent Benzene,

FPM Fluorocarbon Viton Shore D 200C 392F and ozone resistant toluene,petrol



6/13


THREADS

Three different types of th read are g enerally used fo r cam &groove coupling s:

BSP = British Stand ard Pipe

BSPT = British Stand ard Pipe Taper

NPT = National Pipe Taper

In Europe, BSP and BSPTthread s are more commonly used than NPTthread s. NPTthread s are typically American threads. Since manyAmerican industrial machines and products a re exported t o Europea n ma rkets, coupling s with NPTthreads are a regular requirement. The

main difference betw een the three thread types referred to above is the seal method used . Although BSP threads are sealed using a sea l

or o-ring, BSPTand NPTthreads a re sealed b y their conical thread .

THREAD DESCRIPTION STANDARD TYPICALCALLOUT SEALINGMETHOD PROPERTIES

BSP British standard pipe EN ISO 228-1 G1 Parallel thread 55 degree thread angle

DIN ISO 228-1 Pressure tight joint is Trucat ion of rood and crest

obtained with a seal are round

or o-ring Diameter measured in inches

BSPT British standard EN 10226-1 R1 Conical th read. 55 degree thread angle

pipe taper DIN 2999-1 Pressure tight joint is Trucat ion of rood and crest

achieved by the thread are round

BSPP British sta ndard G 1(cyl) Cylindrical threa d 55 degree thread angle

pipe pa rallel Trucat ion of rood and crest

are round

NPT National pipe taper ANSI B 1.20.1 NPT1 Conical thread 60 degree round angle

(American stand ard pipe thread ) Pressure tigh t joint is Trucation of rood and crest

achieved by the thread are flat

COUPLING TYPE STANDARD ONREQUEST

ADAPTOR

Female threaded A BSP EN ISO 228-1/DIN ISO 228-1 NPTANSI B 1.20.1

Male threaded F BSPT EN 10226-1 /DIN 2999-1 NPTANSI B 1.20.1

COUPLER

Female threaded D BSP EN ISO 228-1/DIN ISO 228-1 NPTANSI B 1.20.1

Male threaded B BSPT EN 10226-1 /DIN 2999-1 NPTANSI B 1.20.1

ASSEMBLY

Worm drive clamps

RK safety clamps to EN-14420-3 /DIN 2817

RKP safety clamps to EN-14420-3 /DIN 2817

FLEXOLINE

safety clampsWelding : butt w elding a nd socket welding (see pg . A.1.27)


Cam & groove threads


7/13

TESTING

The following a spects of LMCs cam &groove couplings are tested in house:

Ada ptor a nd co upler dimensions

Material quality

Handle strength

Seal properties

Thread dimensions

Impact resistant

Adaptor and coupler dimensions

High-techno logy mea suring eq uipment

High-techno logy mea suring too ls are used to mea sure the specific dimensions of cam &

groove coupling s to ensure compliance with t he d imensions req uired under the Federal Mil

A-A-59326A, European EN 14420-7 and the German DIN 2828 stand ard s. Altho ug h ord inary

measuring systems are una ble to give sufficiently precise dimensions for th is purpose, our

high-technolog y measuring system is ab le to measure complex cam &groove coupling product

positions and shape s.

Dimension gauges

The shape of the ad apt or coupling e nab les the interchang eab ility of coupler parts. Specially

designed g aug es are used in ad dition to measurement systems. The use of test ga uges

minimises inspection times, ensures interchang eab ility and mainta ins seal properties when

using specially-designed seals, such as envelope seals.

Two ga uges a re used for each d imension; one small and the ot her larger. In the first sta ge of

testing, the small ga uge is passed across the head of the a dapto r section. If the ga uge can not

pass, the ad apt er head falls w ithin t he permissible (minus) tolerances.If the larger gaug e passes across the ad apt or head w ith no interruption, the compo nent is

compliant and its dimensions fa ll within t he pe rmissible + (plus) tolerances.

Material quality

An in-house spectroscope is used to identify the ma terials used in t he ca m &groove coupling s.

The spectroscope ana lyses the precise q uant ity of a ll mat erials of the coupling.

We can t herefore offer our customers a g uarant ee tha t the mat erials used comply fully with the

relevant standard.

Chapt er A: Quick couplings A.1.7

CAM&

GROOVECOUPLIN

GS

FEDMIL/EN/DIN

A.1CAM&GROOVECOUPLINGS FED MIL / EN / DIN


8/13

A.1.8 Chapt er A: Quick coupling s

Handle strength

LMC handles are designed t o resist a w ide range o f applications in many industries. All stand ard ha ndles are investment -cast a nd t rian-

gular in section. The product ion metho d a nd t riang ular section g uarant ees excellent mechan ical properties. The w ear resistance of

this material was t ested using a Rockwell hardness tester. LMC handles achieve bet ter test results than sintered hand les.

Sintered ha ndles begin to fracture w hen subjected to a load of 1600 Kgf, LMC handles do not even sta rt to bend until subjected to a

load of 1000 Kgf. Even w hen sub jected t o a loa d of 2400 Kgf , LMC cam &groove ha ndles still show no sign o f fracture.

Seal properties

After chemical structure, seal compression set has t he next most significant effect on the sea l of cam &groove coupling s. A seal of

correct ha rdness will ensure tha t the cam &groove co upling is sealed properly and safely. Cam &groove sea l hardness is tested using

a durometer.

Thread dimensions

All cam &groove t hreads are tested using t hread g aug es. Our production site has ga uges for all dimensions and all standa rds.

Impact resistance

Impact resistance t ests were carried out on 3 and 4 aluminium couplers and nine ot her brands in order to t est the me chanical

strengt h of LMC cam &groove coupling s. A 2.3 kg /5 lbs weigh t w as d ropped from a height of 1.5 metres /5 feet, and the impact on

the coupler body measured.

A

B

Impact

Drop w eight impact on

bow l of coupler

Orig inal ID: A

ID after impact: B

BRAND PRODUCTIONMETHOD

Se Gravity cast

Sep Gravity cast

Ma Sand cast

Om High pressure die cast

Wa High pressure die cast

Su Sq ueeze die cast

Up High pressure die cast

LMC High pressure die cast

Fu High pressure die cast

0.0 2.5 5.0 7.5 10.0 12.5 15.0

6000

5000

4000

3000

2000

1000

0

* LMC

X0 0P/M

(*) Fra ctured.

(0, ) Bend, not fracture.

Bending st roke (mm) Bend investment cast LMC handle

Load(kgf)

Fractured sintered handle



9/13


CAM&

GROOVECOUPLIN

GS

FEDMIL/EN/DIN

A.1

Test result

The impact resistance test showed tha t the product q uality of ca m &groove co upling s is variable. Nine couplers from different

manufa cturers were also tested.

Four brands o f ada ptor w ere unable to fit the correspond ing coupler following a sing le impact from a 2.3 kg /5 lbs weight dropped

from a height of 1.5 metres /5 feet . However, it took 18 such impacts before LMC-Couplings couplers were unable to fit their ad aptors.

The averag e number of impacts required before fractures became aparent w as 4.25. LMC-Couplings couplers resisted 23 impacts before

show ing signs of fracture; a result far in excess of the a verage va lue.

ImpacttimesB

94.50

88.50

90.50

92.50

C(Se) C(Sep) C(Ma) C(Om)C(Om)C(Wa) C(Su) B(Up) B(Up)C(Up)C(Up)D(Up)C(LMC) C(LMC)

*0*0

*0

*1

*1

*0

*1*1

*1

*0*0

*0

*1*1

*17

*18 *18

*19

*0*0

*0

*1

*2

*2

*2*2

*0

*0

*1

*1

*1

*0

*2

*2*2

*3

*0

FUNCTIONAL

DX(MM)

DISABLED


Size 3

Type C C C C C C C B B C C D C

Brand Se Sep Ma Om Om Wa Su Up Up Up Up Up LMC

Original ID A 92.14 91.72 91.98 92.21 92.01 92.53 91.98 92.24 92.42 92.74 92.58 92.15 93.54

1 91.75 89.43 89.86 91.06 91.67 90.98 91.16 91.43 91.12 91.48 91.59 91.31 93.17

2 91.38 88.65 90.57 90.54 90.08 89.57 91.00 90.43 90.68 91.20 90.75 92.57

3 90.73 90.54 90.27 89.06 88.66 90.26 90.30 90.28 91.11 90.38 92.57

4 90.56 90.25 90.09 90.12 89.28 90.68 90.30 92.35

5 90.16 90.05 89.83 90.65 89.78 92.19

6 90.11 90.00 90.47 89.72 91.92

7 89.55 89.49 91.89

8 89.35 89.44 91.87

9 89.37 89.33 91.79

10 89.33 91.77

11 89.22 91.76

12 89.14 91.55

13 91.68

14 91.58

15 91.58

16 91.6517 91.61

18 91.19

19 91.15

20 91.18

21 91.08

22 90.58

23 90.05

Measurements in mm

Adap tor unab le to fit in coupler

Coupler cracked


10/13


COATINGS

Sometimes sta nda rd cam &groove coupling materials, like stainless steel, are not sufficiently resistant to ext remely agg ressive chemicals.

However, at LMC-Couplings, our couplings feature high-resistance coatings, such as:

ECTFE PTFE

PFA

ECTFE (up to 1000)

ECTFE (Ethylene ch lorotrifluoroet hylene) coating s are designed to resist highly-concentrat ed a nd a gg ressive chemicals. Couplings

with an ECTFE-coating show excellent electric isolating and fire properties and resist to temperatures up to 150C /300F.

PFA (up to 200)

The key quality of a PFA (Perfluoroa lkoxy) coat ing is the t emperat ure resistance up to 260C /500F. Their effect ive ant i-ad -hesive

layer makes PFA coat ings pa rticularly w ell-suited to food and pha rmaceutical industry a pplications.

PTFE (up to 40)PTFE (Poly tet rafluoroet hylene) coat ings a re only 40t hick. PTFE-coa ted coupling s can w ithsta nd t emperatures up to 260C /500F.

Like PFA-coa ted couplings, PTFE couplings have excellent a nti-adhe sive qua lities and are suitable for food indust ry applications.

PVDF (up to 800)

Like ECTFE coa ting s, PVDF (Polyvinylidene fluoride) coat ings ca n resist high ly-concentra ted and a gg ressive chemicals, but w ith the

ad ded a dvan tag e of high temperature resistance. These coupling s are wear-proof and also suitab le for food industry app lications.

PTFE liner

LMC-Couplings is ab le to provide his customers PTFE lined couplings. Our PTFE

facility has been specially built to meet the highest industrial requirements.

This room is separated from our other production facilities to ensure a clean

and dust-free working environment . PTFE lined couplings are used in the pha r-

maceutical, cosmetics and food industry. Please contact our sales department

for further information.



11/13


CAM&

GROOVECOUPLIN

GS

FEDMIL/EN/DIN

A.1

ACCESSORIES

All LMC-Coupling s, cam &groo ve co uplings (stainless steel, b rass, bronz e, a luminium a nd

polypropylene)* as st and ard are supplied w ith sta inless steel investment-cast triangular-section

ha nd les. Sta inless steel provides the best chemical resistance. Their triang ular section and

investment -casting production method improves the mechanical strength o f the hand le.

Even greater security and safety is ensured by LMCs cam &groove couplings with patented

safety hand les. Simply push the nut on the hand le dow nw ards and the coupling connection is

sealed. The safe ty version of LMCs cam &g roove couplings ca n be mad e extra-secure by

using the safety p in, as on a ll stand ard LMC-Couplings cam &groove coupling s.

Where dust ca ps (type DC) are used to t erminat e hose or pipe assemblies, LMCs lockab le han-

dles offer even higher safety levels. These pa tented L-shaped handles are physically locked, so

tha t the dust cap ca n only be removed by unlocking t he hand les with a key. Safety hand les are

also recommend ed to secure dust caps.

* With exception o f 8"

TYPEHANDLE MATERIAL REFERENCE 1/2" 3/4" 1" 1.1/4" 1.1/2" 2" 2.1/2" 3" 4" 5" 6" 8"

Investment-ca st Stainless steel VLHRPR

Investment-cast Brass VLHRPM - - - - - -

Safety locking handle Stainless steel VLHRPR S - - - - - - - -

Cap L-handle Stainless steel VLHRPR L - - - - -

available

- not available

triangular handle standard

triangular handle

Handle types

1

2

3

1 2 3



12/13


CROSS REFERENCES

Cam & groove couplings

Cam & groove seals

COUPLING TYPE DESCRIPTION ENREFERENCE COMMONUSEDREF.

A Adapter, female threaded Federal Mil - 633-ABS

AF Ad apt er, fema le t hrea ded EN 14420-7 /DIN 2828 AF 633-ABSF

with thread seal

B Coupler, fema le threaded EN 14420-7 /MIL spec BF 633-BB

C Coupler, with serrated hose shank Federal Mil - 633-C

CC Coupler, w ith hose shank EN 14420-7 /DIN 2828 CC 633-CC

D Coupler, female threaded Federal Mil - 633-DBS

DF Co upler, fema le t hrea ded EN 14420-7 /DIN 2828 DF 633-DBSF

with thread seal

E Adapter, w ith serrated hose shank Federal Mil - 633-E

EC Ad apter, w ith smoo th ho se sha nk EN 14420-7 /DIN 2828 EC 633-EC

F Adapter, male threaded Federal Mil /EN 14420-7 FF 633-FB

K Female dust cap Federal Mil /EN 14420-7 DC 634-B

P Male dust plug Federal Mil /EN 14420-7 DP 634-A

VL A * 13 *Cam &groove coupling

MaterialA: AluminiumB: BronzeM: BrassP: PolypropyleneR: Sta inless steel

Size

-: Federal Mil A-A-59326AD: EN 14420-7 /DIN 2828S: With safety handlesSD: EN 14420-7 /DIN 2828 with safety ha nd lesN: NPTthread

VL X * 13Cam &groove coupling

Seal

Size

MaterialB: NBR sq ua re sea lE: EPDM sq uare sea lV: FPM square sealH: CSM sq uare sea lP: PTFE /EPDM op en envelop e sea lPG: PTFE /FPM closed envelope sealPSG: FEP /VMQ closed square seal



13/13


CAM&

GROOVECOUPLIN

GS

FEDMIL/EN/DIN

A.1

DIMENSIONS


ND Inch A B C D E F G H J K L

13 1/2" 30 40 31 46 13 31 66 10 46 14 33

20 3/4" 115 50 33 49 19 55 85 14 49 21 34

25 1" 138 62 40 60 24 40 98 20 60 26 41

32 1.1/4 178 81 46 68 31 46 104 26 70 35 48

40 1.1/2 185 87 48 70 38 48 109 32 73 38 50

50 2" 195 90 54 79 48 54 124 43 79 46 57

65 2.1/2 208 111 55 85 62 55 135 54 87 56 59

80 3" 250 143 57 90 75 57 159 66 92 73 62

100 4" 270 171 61 101 100 61 169 89 101 98 65

125 5" 300 - 61 101 122 61 188 118 105 128 65

150 6" 400 254 67 112 150 67 240 140 111 144 73

M N O P S T U V W X Y Z AA

13 24 37 14 10 62 28 24 52 37 14 4 26

13 32 40 19 14 76 25 32 57 40 19 10 26

13 43 48 23 19 92 36 43 69 49 23 10 23

13 50 55 28 25 98 41 58 77 55 28 10 40

13 56 36 36 31 102 44 56 78 56 36 10 42

13 68 62 46 43 117 49 68 87 62 46 10 48

13 85 86 56 56 129 51 85 98 68 56 10 49

13 102 88 73 64 153 51 102 108 70 73 10 51

13 126 78 98 89 168 55 126 118 78 98 12 53

13 - 83 118 118 188 56 - 103 63 118 12 58

16 - 82 150 138 230 60 - 108 68 150 12 58

Dimensions in mm and are given as illustration only.

a1 c Gtechnical

Documents

Transcript of a1 c Gtechnical