A SEMINAR REPORT ON FRICTION WELDING.ppt
-
Upload
patel-ketan -
Category
Documents
-
view
139 -
download
1
Transcript of A SEMINAR REPORT ON FRICTION WELDING.ppt
![Page 1: A SEMINAR REPORT ON FRICTION WELDING.ppt](https://reader033.fdocuments.in/reader033/viewer/2022061110/5453994bb1af9fb0578b4998/html5/thumbnails/1.jpg)
A SEMINAR REPORT ON FRICTION
WELDING
PRESENTED BY:-
![Page 2: A SEMINAR REPORT ON FRICTION WELDING.ppt](https://reader033.fdocuments.in/reader033/viewer/2022061110/5453994bb1af9fb0578b4998/html5/thumbnails/2.jpg)
DEFINATION
Friction welding is a solid state welding
process where in coalescence is produced by
the heat obtained from mechanically induced
sliding motion between rubbing surfaces. The
work parts are held together under pressure.
![Page 3: A SEMINAR REPORT ON FRICTION WELDING.ppt](https://reader033.fdocuments.in/reader033/viewer/2022061110/5453994bb1af9fb0578b4998/html5/thumbnails/3.jpg)
FIG:-1.1 FRICTION WELDING MACHINE
![Page 4: A SEMINAR REPORT ON FRICTION WELDING.ppt](https://reader033.fdocuments.in/reader033/viewer/2022061110/5453994bb1af9fb0578b4998/html5/thumbnails/4.jpg)
OPERATION STEP FOR FRICTION WELDING:-
STEP:-1
The two components to be friction welded are held in axial
alignment.
![Page 5: A SEMINAR REPORT ON FRICTION WELDING.ppt](https://reader033.fdocuments.in/reader033/viewer/2022061110/5453994bb1af9fb0578b4998/html5/thumbnails/5.jpg)
STEP 2:-
One component that is held in chucking spindle of
the machine is rotated and accelerated to the desired
speed.
![Page 6: A SEMINAR REPORT ON FRICTION WELDING.ppt](https://reader033.fdocuments.in/reader033/viewer/2022061110/5453994bb1af9fb0578b4998/html5/thumbnails/6.jpg)
STEP 3:- The other component that is held in the movable clamp is moved forward to come into pressure contact with the rotating component.
![Page 7: A SEMINAR REPORT ON FRICTION WELDING.ppt](https://reader033.fdocuments.in/reader033/viewer/2022061110/5453994bb1af9fb0578b4998/html5/thumbnails/7.jpg)
STEP 4:-
Pressure and rotation are maintained until the resulting high temp
makes the component’s metal plastic for welding with sufficient
metal behind the interface becoming softened to permit the
components to be forged together. During this period metal is slowly
extruded from the weld region to form an upset
![Page 8: A SEMINAR REPORT ON FRICTION WELDING.ppt](https://reader033.fdocuments.in/reader033/viewer/2022061110/5453994bb1af9fb0578b4998/html5/thumbnails/8.jpg)
ADVANTAGES OF FRICTION WELDING:-
1. Simplicity of operation.
2. Low power requirements.
3. Less time for welding.
4. Compare to flash and resistance butt welding friction welding produce
improved welds at higher speed and lower cost, less electrical current
is required.
5. Fully automated.
6. There is no flux, filler metal or slag presents.
7. With friction welding there is less shorting of the components.
![Page 9: A SEMINAR REPORT ON FRICTION WELDING.ppt](https://reader033.fdocuments.in/reader033/viewer/2022061110/5453994bb1af9fb0578b4998/html5/thumbnails/9.jpg)
DISADVANTAGES OF FRICTION WELDING:-
1. The use of this process is restricted to flat and angular butt welds, where one part is normal to the other part.
2. So far the process has been applied only to the joining of small pieces in the form of bar stock
3. Sometimes, quite a heavy flash is forced out in all inertia and friction welds.
4. If tubing is welded, flash may have to be removed from inside the joint.
5. Flash from medium and high carbon steels being hard, must either be removed while it is hot or annealed before it is machined.
6. Thrust pressures in inertia welding will range from 700 to 2800 kg/cm2, which require machine.
![Page 10: A SEMINAR REPORT ON FRICTION WELDING.ppt](https://reader033.fdocuments.in/reader033/viewer/2022061110/5453994bb1af9fb0578b4998/html5/thumbnails/10.jpg)
APPLICATION OF FRICTION WELDING:-
1. Friction welding is use for joining steels, super alloys, nonferrous metals and combination of metals.
2. Among its varied applications are:Production of steering shafts and worm gears, control shafts, axle shafts, engine valves, transmission shafts etc., for automobile indus.
![Page 11: A SEMINAR REPORT ON FRICTION WELDING.ppt](https://reader033.fdocuments.in/reader033/viewer/2022061110/5453994bb1af9fb0578b4998/html5/thumbnails/11.jpg)
PRACTICAL APPLICATION:-
Engine valves Driveshaft
![Page 12: A SEMINAR REPORT ON FRICTION WELDING.ppt](https://reader033.fdocuments.in/reader033/viewer/2022061110/5453994bb1af9fb0578b4998/html5/thumbnails/12.jpg)
CONTINUOUS:-
Axles Turbochargers