a project on automatic traffic control using IC 555
-
Upload
jack990315 -
Category
Engineering
-
view
80 -
download
4
Transcript of a project on automatic traffic control using IC 555
![Page 1: a project on automatic traffic control using IC 555](https://reader036.fdocuments.in/reader036/viewer/2022081419/58ed63a31a28ab605e8b4567/html5/thumbnails/1.jpg)
A project on automatic traffic control
GUIDED BY : A.M.VORA
PRESENTED BY :BABARIYA JASMIN H. (146030309002)BORAD PARTH V. (146030309014)ANAND RAJ N. (146030309125)GAMI JAYESH G. (146030309514)
![Page 2: a project on automatic traffic control using IC 555](https://reader036.fdocuments.in/reader036/viewer/2022081419/58ed63a31a28ab605e8b4567/html5/thumbnails/2.jpg)
The function of traffic lights is to provide sophisticated control and co-ordination to ensure that traffic moves as smoothly and safely as possible.
Function
![Page 3: a project on automatic traffic control using IC 555](https://reader036.fdocuments.in/reader036/viewer/2022081419/58ed63a31a28ab605e8b4567/html5/thumbnails/3.jpg)
History of Traffic light
The world's very first traffic lights were invented by J P Knight installed near London's Hothe intersection of George and Bridge Street use of Commons, which was on, in 1868.
In 1914 The American Traffic Signal Company installed red and green traffic lights on every corner of the intersection of 105th Street and Euclid Avenue in Cleveland, Ohio. First traffic lights were all controlled by either timing, or manually switched
![Page 4: a project on automatic traffic control using IC 555](https://reader036.fdocuments.in/reader036/viewer/2022081419/58ed63a31a28ab605e8b4567/html5/thumbnails/4.jpg)
The free left turn condition is provided
throughout the entire signal period.
The control can also be exercised manual when desired.
Features of Traffic light
![Page 5: a project on automatic traffic control using IC 555](https://reader036.fdocuments.in/reader036/viewer/2022081419/58ed63a31a28ab605e8b4567/html5/thumbnails/5.jpg)
Block Diagram
IC 555&
IC 4017 TRAFFIC LIGHT
9 V DC SUPPLY
![Page 6: a project on automatic traffic control using IC 555](https://reader036.fdocuments.in/reader036/viewer/2022081419/58ed63a31a28ab605e8b4567/html5/thumbnails/6.jpg)
Circuit Diagram
![Page 7: a project on automatic traffic control using IC 555](https://reader036.fdocuments.in/reader036/viewer/2022081419/58ed63a31a28ab605e8b4567/html5/thumbnails/7.jpg)
1. IC 555 IC 555 provide time delay in circuit and also work as oscillator.
2. IC 4017 It takes clock signal from the clock input and turn on the 10 output in sequence , each time when it receives clock input pulses.
Component and Description
![Page 8: a project on automatic traffic control using IC 555](https://reader036.fdocuments.in/reader036/viewer/2022081419/58ed63a31a28ab605e8b4567/html5/thumbnails/8.jpg)
3. Register 330E : A movable metal is rotated in clockwise or anticlockwise direction that changes the resistance of preset
4. Capacitor It is used to temporarily store electrical energy in an electric field.
![Page 9: a project on automatic traffic control using IC 555](https://reader036.fdocuments.in/reader036/viewer/2022081419/58ed63a31a28ab605e8b4567/html5/thumbnails/9.jpg)
5. Diode IN4007 This is a simple, very common rectifier diode, and used for reverse voltage protection.
6. LED It is a two-led semiconductor light source.
![Page 10: a project on automatic traffic control using IC 555](https://reader036.fdocuments.in/reader036/viewer/2022081419/58ed63a31a28ab605e8b4567/html5/thumbnails/10.jpg)
IC 555Pin 1 (Ground): Function of Pin 1 is to ground.
Pin 2 (Trigger): Pin 2 detects rail voltage and gives output very high, when Pin 6 is low.
Pin 3 (Output): Pin 3 goes High and Low and deliver up to 200Ma
Pin 4 (Reset): Pin 4 works to reset the chip.
Pin 5 (Control): Pin 5 is use to control circuit IC4017.
Pin Description
![Page 11: a project on automatic traffic control using IC 555](https://reader036.fdocuments.in/reader036/viewer/2022081419/58ed63a31a28ab605e8b4567/html5/thumbnails/11.jpg)
Pin 6 (Threshold): Pin 6 detects rail voltage and gives output very low , when Pin 2 is High.
Pin 7 (Discharge): Pin 7 goes low when Pin 6 detects rail voltage and Pin 7 remains low only. While Pin 7 not goes high.
Pin 8 (Supply): Connects to the positive power supply (Vs). This can be any voltage between 5V DC.
![Page 12: a project on automatic traffic control using IC 555](https://reader036.fdocuments.in/reader036/viewer/2022081419/58ed63a31a28ab605e8b4567/html5/thumbnails/12.jpg)
IC4017Pin-1: It is the output 5. It goes high when the counter reads 5 counts.
Pin-2: It is the output 1. It goes high when the counter reads 0 counts.
Pin-3: It is the output 0. It goes high when the counter reads 0 counts.
Pin-4: It is the output 2. It goes high when the counter reads 2 counts.
Pin-5: It is the output 6. It goes high when the counter reads 6 counts.
Pin-6: It is the output 7. It goes high when the counter reads 7 counts.
Pin-7: It is the output 3. It goes high when the counter reads 3 counts.
Pin-8: It is the Ground pin which should be connected to a LOW voltage (0V)
Pin-9: It is the output 8. It goes high when the counter reads 8 counts.
Pin-10: It is the output 4. It goes high when the counter reads 4 counts.
![Page 13: a project on automatic traffic control using IC 555](https://reader036.fdocuments.in/reader036/viewer/2022081419/58ed63a31a28ab605e8b4567/html5/thumbnails/13.jpg)
.
Pin-11: It is the output 9. It goes high when the counter reads 9 counts.
Pin-13: Pin 13 is connected to ground and it has logic LOW voltage.
Pin-14: This pin is the clock input. This is the pin from where we need to give the input clock pulses to the IC in order to advance the count. The count advances on the rising edge of the clock.
Pin-15: This is the reset pin which should be kept LOW for normal operation. If you need to reset the IC, then you can connect this pin to HIGH voltage.
Pin-16: This is the power supply pin. This should be given a HIGH voltage of 5V for the IC to function.
![Page 14: a project on automatic traffic control using IC 555](https://reader036.fdocuments.in/reader036/viewer/2022081419/58ed63a31a28ab605e8b4567/html5/thumbnails/14.jpg)
Working IC 555 and counter IC 4017 are used in this circuit.
When the supply is given to the circuit, the gate pulse is generated.
The gate pulse is then given to counter IC 4017 in Pin CP0.
In this circuit IC 555 is work as monostable multivibrator.
It can be produced by adding register and a capacitor to the connected to the basic
timer IC.
Output (Vout is taken from pin 3.)
Pin 2 are shorted and connected to the ground.
Pin 6 and 7 is connected to +VCC through a variable register and between pin 6
and 7 register RB is connected.
![Page 15: a project on automatic traffic control using IC 555](https://reader036.fdocuments.in/reader036/viewer/2022081419/58ed63a31a28ab605e8b4567/html5/thumbnails/15.jpg)
Supply is connected to MR in counter to start.
When the clock pulse is not given to the circuit, it will not conduct.
Gate pulse is given through output of the IC 555 and given to the pin
CP0.
Then the counter will conduct.
Then the output is taken from Q0, Q1, Q2, Q3…………Q9.
CP1 is grounded.
When the logic level is 1 at Q0 then Q1, Q2, Q3 are at logic level 0
then also the output of Q1, Q2, Q3 are conduit because all the Q0 to
Q3 is connected parallel with diode.
At that time other output Q4 to Q9 all are at logic level 0.
![Page 16: a project on automatic traffic control using IC 555](https://reader036.fdocuments.in/reader036/viewer/2022081419/58ed63a31a28ab605e8b4567/html5/thumbnails/16.jpg)
Provide for orderly movement of traffic Increase capacity at intersection Reduce frequency and severity of certain kind of clashes Provide continuous movement of traffic at a desired speed Interrupt heavy traffic to allow pedestrians to pass Effectively perform traffic management
Advantage
![Page 17: a project on automatic traffic control using IC 555](https://reader036.fdocuments.in/reader036/viewer/2022081419/58ed63a31a28ab605e8b4567/html5/thumbnails/17.jpg)
Disadvantage
Increase in AccidentsDelayDiverted CongestionCivil Disobedience
![Page 18: a project on automatic traffic control using IC 555](https://reader036.fdocuments.in/reader036/viewer/2022081419/58ed63a31a28ab605e8b4567/html5/thumbnails/18.jpg)
APPLICATION
Bridge Construction 2-Lane Road Construction Power Outage Downed Signal Replacement Utility Work Bridge Painting Culvert installation Event Traffic Control Natural Disaster Traffic Control Tree trimming Heavy equipment traffic organization Emergency Response
![Page 19: a project on automatic traffic control using IC 555](https://reader036.fdocuments.in/reader036/viewer/2022081419/58ed63a31a28ab605e8b4567/html5/thumbnails/19.jpg)
SNAP SHOT OF OUR PROJECT
![Page 20: a project on automatic traffic control using IC 555](https://reader036.fdocuments.in/reader036/viewer/2022081419/58ed63a31a28ab605e8b4567/html5/thumbnails/20.jpg)
SNAP SHOT OF OUR PROJECT