A Bluffton Motor Works Company - Weg-cmweg-cm.com/wp-content/uploads/2017/03/Toledo Gearmotor...
24
Gear Reducer Catalog C70-LHL INLINE PARALLEL SHAFT REDUCERS RIGHT ANGLE REDUCERS RIGHT ANGLE REDUCERS - DC MOTOR FRAME MI-10 CE L60 C TC-43 I A Bluffton Motor Works Company
Transcript of A Bluffton Motor Works Company - Weg-cmweg-cm.com/wp-content/uploads/2017/03/Toledo Gearmotor...
Gear ReducerCatalog
C70-LHL
INLINE PARALLEL SHAFT REDUCERS
RIGHT ANGLE REDUCERS
RIGHT ANGLE REDUCERS - DC MOTOR FRAME
MI-10 CE
L60 C
TC-43 I
A Bluffton Motor Works Company
CONTENTS PAGE
In-Line Parallel Gear Reducers MI-10 CE . . . . . . . . . . . . . . . . . . . . . . . . . . . . p . 3 MI-10 EE . . . . . . . . . . . . . . . . . . . . . . . . . . . . p . 4 MI-10 CL . . . . . . . . . . . . . . . . . . . . . . . . . . . . p . 5 M164-56C . . . . . . . . . . . . . . . . . . . . . . . . . . p . 6 M164-48N . . . . . . . . . . . . . . . . . . . . . . . . . . p . 7 M164-56N . . . . . . . . . . . . . . . . . . . . . . . . . . p . 8
Right Angle Reducers TC 43 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . p . 9 L60 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . p .10 C55 HS . . . . . . . . . . . . . . . . . . . . . . . . . . . . p .11 C55 RS . . . . . . . . . . . . . . . . . . . . . . . . . . . . p .12 C55 ES . . . . . . . . . . . . . . . . . . . . . . . . . . . . p .13 C55 LHL . . . . . . . . . . . . . . . . . . . . . . . . . . . p .14 C70 HS . . . . . . . . . . . . . . . . . . . . . . . . . . . . p .15 C70 RS . . . . . . . . . . . . . . . . . . . . . . . . . . . . p .16 C70 H43S . . . . . . . . . . . . . . . . . . . . . . . . . . p .17 C70 LGHS . . . . . . . . . . . . . . . . . . . . . . . . . . p .18 C70 LHL . . . . . . . . . . . . . . . . . . . . . . . . . . . p .19 U-50 RS . . . . . . . . . . . . . . . . . . . . . . . . . . . . p .20
Right Angle Reducers/DC Motor Frame CE 34 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . p .21 L 60 C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . p .22 L 60 D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . p .23 TC 43 I . . . . . . . . . . . . . . . . . . . . . . . . . . . . . p .24
MI-10-EE page 4
M164 48N page 7
TC 43 page 9
C70 LHL page 20
L60D page 23
2
419/885-3769 • Fax 419/885-3799 • www.toledogear.com
IN-LINE GEAR REDUCERS MI-10 CEStructural & Design Features:• Parallel Shaft Two-Stage Spur Gear Reducer• Induction Hardened Teeth on all Gears and Pinions• Annealed Aluminum Housing, Precision Machined for Accurate Shaft Alignment• Pinions Cut Integral with Shafts• Ball Bearings on Output Shaft• Adaptor for Face-Mounting NEMA 56C Motor (with 5/8” Diameter Shaft, 3/16” Keyway)
Output Options:• Available with 1 Gear Ratio (See Chart Below)
Dimensions and Ratings
Ratio 10:1
Output Speed,RPM 172.5
Input Hp. .50
Max OutputTorque, In.-lbs. 182
5/16-18 TH’D X .56 DEEP4 HOLESØ 5.00 BOLT CIRCLE
Rear View (Input end)Mounting Dimensions for NEMA 56C Motor
Front View (Output end)
3
All data is for an Operating Service Factor of 1 at l725 RPM input speed.(consult Mfgr. for allowable overhung loads)
Ø.406 - 4 HOLESCSK FOR 3/8 F.H. SCREW(OPPOSITE SIDE)Ø 5.875 BOLT CIRCLE
3/16 ST’D KEYWAY
4
IN-LINE GEAR REDUCERS MI-10 EEStructural & Design Features:• Parallel Shaft Two-Stage Spur Gear Reducer• Induction Hardened Teeth on all Gears and Pinions• Annealed Aluminum Housing, Precision Machined for Accurate Shaft Alignment• Pinions Cut Integral with Shafts• Ball Bearings on Output Shaft• Flanged and Bored for Mounting NEMA 48N Motor (Oil Burner Type)
Output Options:• Available with 1 Gear Ratio (See Chart Below)
Dimensions and Ratings
Ratio 10:1
Output Speed,RPM 172.5
Input Hp. .50
Max OutputTorque, In.-lbs. 182
All data is for an Operating Service Factor of 1 at l725 RPM input speed(consult Mfgr. for allowable overhung loads)
Front View (Output end)
5/16-18 TH’D X .56 DEEP4 HOLESØ 5.00 BOLT CIRCLE
Ø 5015.5005
Rear View (Input end)Mounting Dimensions for NEMA 48N Motor
5/16-18 TH’D - 2 HOLES
419/885-3769 • Fax 419/885-3799 • www.toledogear.com
IN-LINE GEAR REDUCERS MI-10 CLStructural & Design Features:• Parallel Shaft Two-Stage Spur Gear Reducer• Induction Hardened Teeth on all Gears and Pinions• Annealed Aluminum Housing, Precision Machined for Accurate Shaft Alignment• Pinions Cut Integral with Shafts• Ball Bearings on Output Shaft• Adaptor for Face-Mounting NEMA 56C Motor (with 5/8” Diameter Shaft, 3/16” Keyway)
Output Options:• Available with 1 Gear Ratio (See Chart Below)
Dimensions and Ratings
5
Ratio 2.06:1
Output Speed,RPM 837.4
Input Hp. 2.12
Max OutputTorque, In.-lbs. 156
All data is for an Operating Service Factor of 1 at l725 RPM input speed(consult Mfgr. for allowable overhung loads)Front View (Output end)
Rear View (Input end)Mounting Dimensions for NEMA 56C Motor
5/16-18 TH’D X .56 DEEP4 HOLESØ 5.00 BOLT CIRCLE
3/16 ST’D KEYWAYØ.406 - 4 HOLESCSK FOR 3/8 F.H. SCREW(OPPOSITE SIDE)Ø 5.875 BOLT CIRCLE
6
IN-LINE GEAR REDUCERS M164-56CStructural & Design Features:• Parallel Shaft Two-Stage Gear Reducer• Induction Hardened Teeth on all Gears and Pinions• Die Cast Aluminum Housing, Precision Machined for Accurate Shaft Alignment• Pinions Cut Integral with Shafts• Ball Bearings on Output Shaft• Adaptor for Face-Mounting NEMA 56C Motor (with 5/8” Diameter Shaft, 3/16” Keyway)• Helical Gearing Available for Industrial and
Commercial OEM Applications
Output Options:• Available with 10 Gear Ratios (See Chart Below)
Dimensions and Ratings
MODEL M164-X M164-E M164-A M164-L M164-B M164-F M164-K M164-C M164-D M164-G
RATIO 11.08 9.11 7.63 6.48 5.56 4.81 4.18 3.91 3.20 2.63RPM out(at 1725RPM in) 156 189 226 266 310 358 412 441 539 657
INPUT 0.75 0.90 1.07 1.25 1.48 1.48 1.48 1.48 1.48 1.48 Hp
TORQUE 290 294 285 290 290 255 231 204 167 140 max outputin-lbs.
All data is for an Operating Service Factor of 1 at l725 RPM input speed(consult Mfgr. for allowable overhung loads and for additional output shaft configurations)
Front View (Output end)
Rear View (Input end)Mounting Dimensions for NEMA 56C Motor
5/16-18 TH’D X .53 DEEP4 HOLESØ 5.00 BOLT CIRCLE
MODEL M164-X M164-E M164-A M164-L M164-B M164-F M164-K M164-C M164-D M164-G
RATIO 11.08 9.11 7.63 6.48 5.56 4.81 4.18 3.91 3.20 2.63RPM out(at 1725RPM in) 156 189 226 266 310 358 412 441 539 657
INPUT 0.75 0.90 1.07 1.25 1.48 1.48 1.48 1.48 1.48 1.48 Hp
TORQUE 290 294 285 290 290 255 231 204 167 140 max outputin-lbs.
7419/885-3769 • Fax 419/885-3799 • www.toledogear.com
IN-LINE GEAR REDUCERS M164-48NStructural & Design Features:• Parallel Shaft Two-Stage Gear Reducer• Induction Hardened Teeth on all Gears and Pinions• Die Cast Aluminum Housing, Precision Machined for Accurate Shaft Alignment• Pinions Cut Integral with Shafts• Ball Bearings on Output Shaft• Flanged and Bored for Mounting NEMA 48N (Oil Burner Type) Motor
Output Options:• Available with 10 Gear Ratios (See Chart Below)
Dimensions and Ratings
Rear View (Input end)Mounting Dimensions for NEMA 48N Motor
5/16-18 TH’D2 HOLES
All data is for an Operating Service Factor of 1 at l725 RPM input speed(consult Mfgr. for allowable overhung loads and for additional output shaft configurations)
Front View (Output end)
8
IN-LINE GEAR REDUCERS M164-56N
Dimensions and Ratings
Structural & Design Features:• Parallel Shaft Two-Stage Gear Reducer• Induction Hardened Teeth on all Gears and Pinions• Die Cast Aluminum Housing, Precision Machined for Accurate Shaft Alignment• Pinions Cut Integral with Shafts• Ball Bearings on Output Shaft• Flanged and Bored for Face-Mounting NEMA 56N (Oil Burner Type) Motor with 5/8” Dia. Shaft, 3/16” Keyway)
Output Options:• Available with 10 Gear Ratios (See Chart Below)
Front View (Output end)
Ø .6257
.62513/16 ST’D KEYWAY
5/16-18 TH’D2 HOLES
MODEL M164-X M164-E M164-A M164-L M164-B M164-F M164-K M164-C M164-D M164-G
RATIO 11.08 9.11 7.63 6.48 5.56 4.81 4.18 3.91 3.20 2.63RPM out(at 1725RPM in) 156 189 226 266 310 358 412 441 539 657
INPUT 0.75 0.90 1.07 1.25 1.48 1.48 1.48 1.48 1.48 1.48 Hp
TORQUE 290 294 285 290 290 255 231 204 167 140max outputin-lbs.
All data is for an Operating Service Factor of 1 at l725 RPM input speed(consult Mfgr. for allowable overhung loads and for additional output shaft configurations)
Rear View (Input end)Mounting Dimensions for NEMA 56N Motor
9419/885-3769 • Fax 419/885-3799 • www.toledogear.com
RIGHT ANGLE GEAR REDUCERS TC 43TC Style Structural & Design Features:• Right Angle Worm-Gear Reducer• Forged Manganese Bronze Worm-Gear• Induction Hardened, Ground and Polished Worm• Annealed Cast Iron Housing, Precision Machined for Accurate Shaft Alignment• Ball Bearings on Input Shaft• Tapered Roller Bearings on Output Shaft• High-Strength, Heat Treated Input and Output Shafts• Flange for Face-Mounting NEMA 56C Frame Motor
Output Options:• Available with 3 Shaft Extensions - 7L, 7B, 7R• 5/8" Dia. Output Shaft Available
Dimensions and Ratings
RATIO 5.5 10 14.5 20 30 40 61
OUTPUT SPEED, RPM 314 172.5 118.97 86.25 57.5 43.12 28.28
HP IN 1.31 1.14 0.90 0.69 0.47 0.42 0.27
HP OUT 1.19 1.00 0.75 0.54 0.33 0.27 0.14
TORQUE OUT, IN.-LBS. 239 367 401 401 367 399 332
Overhung Load on Output Shaft, 400 lbs. at 1.00 in. from Housing or Output CapAll data is for a Service Factor of 1 at 1725 RPM input speed
Ø.406 -4 HOLES
Ø 4.5020
4.5005
3/16 x 3/32ST’D KEYWAY
7L 7B 7R
TC43-7B-40
(7L, 7B, 7R)
10
RIGHT ANGLE GEAR REDUCERS L60
Dimensions and Ratings
L60 Style Structural & Design Features:• Right Angle Worm-Gear Reducer• Forged Manganese Bronze Worm-Gear• Induction Hardened, Ground and Polished Worm• Annealed Cast Iron Housing, Precision Machined for Accurate Shaft Alignment• Ball Bearings on Input Shaft Front and Back• Tapered Roller Bearings on Output Shaft• High-Strength, Heat Treated Input and Output Shafts
Output Options:• Available with 3 Shaft Extensions - L, B, R
RATIO 5.5 10 14.5 20 30 40 61
OUTPUT SPEED, RPM 314 172.5 118.97 86.25 57.5 43.12 28.28
HP IN 1.31 1.14 0.90 0.69 0.47 0.42 0.27
HP OUT 1.19 1.00 0.75 0.54 0.33 0.27 0.14
TORQUE OUT, IN.-LBS. 239 367 401 401 367 399 332
Overhung Load on Output Shaft, 400 lbs. at 1.00 in. from Housing or Output CapAll data is for a Service Factor of 1 at 1725 RPM input speed
Ø.405 - 4 HOLES 3/16 X 3/32 ST’D KEYWAY
3/16 X 3/32 ST’D KEYWAY
11419/885-3769 • Fax 419/885-3799 • www.toledogear.com
RIGHT ANGLE GEAR REDUCERS C55-HS
Dimensions and Ratings
HS Style Structural & Design Features:• Right Angle Worm-Gear Reducer• Forged Manganese Bronze Worm-Gear• Induction Hardened, Ground and Polished Worm• Annealed Cast Iron Housing, Precision Machined for Accurate Shaft Alignment• Ball Bearings on Input Shaft Front and Back• Tapered Roller Bearings on Output Shaft• High-Strength, Heat Treated Input and Output Shafts• Flange for Face-Mounting NEMA 56C Frame Motor
Output Options:• Available with 3 Shaft Extensions - L, B, R
RATIO 10 15 20 24 30 40 45 48 60
OUTPUT SPEED, RPM 172.5 115 86.25 71.87 57.5 43.13 38.33 35.94 28.75
HP IN 1.89 1.40 1.14 0.99 0.84 0.67 0.61 0.58 0.48
HP OUT 1.69 1.18 0.93 0.77 0.62 0.46 0.41 0.38 0.28
TORQUE OUT, IN.-LBS. 617 650 675 679 681 673 665 658 620
Overhung Load on Output Shaft, 780 lbs. at 1.25 in. from Housing or Output CapAll data is for a Service Factor of 1 at 1725 RPM input speed
Ø.406 -4 HOLES
Ø 4.5020
4.5005
Ø .406 - 4 HOLES Ø 5.875 BOLT CIRCLE
Ø .6.50
Ø .627
.626
3/16 X 3/32 ST’D KEYWAY
1/4 X 1/8 ST’D KEYWAY
12
RIGHT ANGLE GEAR REDUCERS C55 RS
Dimensions and Ratings
RS Style Structural & Design Features:• Right Angle Worm-Gear Reducer• Forged Manganese Bronze Worm-Gear• Induction Hardened, Ground and Polished Worm• Annealed Cast Iron Housing, Precision Machined for Accurate Shaft Alignment• Ball Bearings on Input Shaft Front and Back• Tapered Roller Bearings on Output Shaft• High-Strength, Heat Treated Input and Output Shafts
Output Options:• Available with 3 Shaft Extensions - L, B, R
RATIO 10 15 20 24 30 40 45 48 60
OUTPUT SPEED, RPM 172.5 115 86.25 71.87 57.5 43.13 38.33 35.94 28.75
HP IN 1.89 1.40 1.14 0.99 0.84 0.67 0.61 0.58 0.48
HP OUT 1.69 1.18 0.93 0.77 0.62 0.46 0.41 0.38 0.28
TORQUE OUT, IN.-LBS. 617 650 675 679 681 673 665 658 620
Overhung Load on Output Shaft, 780 lbs. at 1.25 in. from Housing or Output CapAll data is for a Service Factor of 1 at 1725 RPM input speed
Ø.406 -4 HOLES
3/16 X 3/32 ST’D KEYWAY
1/4 X 1/8 ST’D KEYWAY
419/885-3769 • Fax 419/885-3799 • www.toledogear.com
RIGHT ANGLE GEAR REDUCERS C55 ES
Dimensions and Ratings
13
ES Style Structural & Design Features:• Right Angle Worm-Gear Reducer• Forged Manganese Bronze Worm-Gear• Induction Hardened, Ground and Polished Worm• Annealed Cast Iron Housing, Precision Machined for Accurate Shaft Alignment• Ball Bearings on Input Shaft Front and Back• Tapered Roller Bearings on Output Shaft• High-Strength, Heat Treated Input and Output Shafts
Output Options:• Available with 3 Shaft Extensions - L, B, R
RATIO 10 15 20 24 30 40 45 48 60
OUTPUT SPEED, RPM 172.5 115 86.25 71.87 57.5 43.13 38.33 35.94 28.75
HP IN 1.89 1.40 1.14 0.99 0.84 0.67 0.61 0.58 0.48
HP OUT 1.69 1.18 0.93 0.77 0.62 0.46 0.41 0.38 0.28
TORQUE OUT, IN.-LBS. 617 650 675 679 681 673 665 658 620
Overhung Load on Output Shaft, 780 lbs. at 1.25 in. from Housing or Output CapAll data is for a Service Factor of 1 at 1725 RPM input speed
Ø.406 -4 HOLES
3/16 X 3/32 ST’D KEYWAY
1/4 X 1/8 ST’D KEYWAY
Ø .406 - 4 HOLES Ø 5.875 BOLT CIRCLE
C55-ES-B-40
RIGHT ANGLE GEAR REDUCERS C55 LHL
Dimensions and Ratings
14
HS Style Structural & Design Features:• Right Angle Worm-Gear Reducer• Forged Manganese Bronze Worm-Gear• Induction Hardened, Ground and Polished Worm• Annealed Cast Iron Housing, Precision Machined for Accurate Shaft Alignment• Ball Bearings on Input Shaft Front and Back• Tapered Roller Bearings on Output Shaft• High-Strength, Heat Treated Input and Output Shafts• Extended End Bells on Output Shaft for Long Shaft Requirements and Bearing Supports• Flange for Face-Mounting NEMA 56C Frame Motor• Available Through Input Shaft for Clutch and Brake
Output Options:• Available with 3 Shaft Extensions - L, B, R
RATIO 10 15 20 24 30 40 45 48 60
OUTPUT SPEED, RPM 172.5 115 86.25 71.87 57.5 43.13 38.33 35.94 28.75
HP IN 1.89 1.40 1.14 0.99 0.84 0.67 0.61 0.58 0.48
HP OUT 1.69 1.18 0.93 0.77 0.62 0.46 0.41 0.38 0.28
TORQUE OUT, IN.-LBS. 617 650 675 679 681 673 665 658 620
Overhung Load on Output Shaft, 660 lbs. at 1.50 in. from Output CapAll data is for a Service Factor of 1 at 1725 RPM input speed
Ø.406 -4 HOLES
3/16 X 3/32 ST’D KEYWAY
1/4 X 1/8 ST’D KEYWAY
Ø .406 - 4 HOLES Ø 5.875 BOLT CIRCLE
419/885-3769 • Fax 419/885-3799 • www.toledogear.com
RIGHT ANGLE GEAR REDUCERS C70 HS
Dimensions and Ratings
15
HS Style Structural & Design Features:• Right Angle Worm-Gear Reducer• Forged Manganese Bronze Worm-Gear• Induction Hardened, Ground and Polished Worm• Annealed Cast Iron Housing, Precision Machined for Accurate Shaft Alignment• Ball Bearings on Input Shaft Front and Back• Tapered Roller Bearings on Output Shaft• High-Strength, Heat Treated Input and Output Shafts• Flange for Face-Mounting NEMA 56C Frame Motor
Output Options:• Available with 3 Shaft Extensions - L, B, R
RATIO 10 12 20 24 30 40 48 60
OUTPUT SPEED, RPM 172.5 143.7 86.25 71.87 57.5 43.13 35.94 28.75
HP IN 3.36 2.96 2.00 1.72 1.45 1.15 0.99 0.80
HP OUT 3.06 2.65 1.69 1.42 1.14 0.84 0.69 0.52
TORQUE OUT, IN.-LBS. 1119 1164 1236 1243 1248 1235 1208 1138
Overhung Load on Output Shaft, 850 lbs. at 1.25 in. from Housing or Output CapAll data is for a Service Factor of 1 at 1725 RPM input speed
Ø.406 -4 HOLES
3/16 X 3/32 ST’D KEYWAY
1/4 X 1/8 ST’D KEYWAY
Ø .406 - 4 HOLES Ø 5.875 BOLT CIRCLE
RIGHT ANGLE GEAR REDUCERS C70 RS
Dimensions and Ratings
16
RS Style Structural & Design Features:• Right Angle Worm-Gear Reducer• Forged Manganese Bronze Worm-Gear• Induction Hardened, Ground and Polished Worm• Annealed Cast Iron Housing, Precision Machined for Accurate Shaft Alignment• Ball Bearings on Input Shaft Front and Back• Tapered Roller Bearings on Output Shaft• High-Strength, Heat Treated Input and Output Shafts
Output Options:• Available with 3 Shaft Extensions - L, B, R
RATIO 10 12 20 24 30 40 48 60
OUTPUT SPEED, RPM 172.5 143.7 86.25 71.87 57.5 43.13 35.94 28.75
HP IN 3.36 2.96 2.00 1.72 1.45 1.15 0.99 0.80
HP OUT 3.06 2.65 1.69 1.42 1.14 0.84 0.69 0.52
TORQUE OUT, IN.-LBS. 1119 1164 1236 1243 1248 1235 1208 1138
Overhung Load on Output Shaft, 850 lbs. at 1.25 in. from Housing or Output CapAll data is for a Service Factor of 1 at 1725 RPM input speed
Ø.406 -4 HOLES
3/16 X 3/32 ST’D KEYWAY 1/4 X 1/8 ST’D
KEYWAY
Ø .625
.624
419/885-3769 • Fax 419/885-3799 • www.toledogear.com
RIGHT ANGLE GEAR REDUCERS C70 H43S
Dimensions and Ratings
17
HS Style Structural & Design Features:• Right Angle Worm-Gear Reducer• Forged Manganese Bronze Worm-Gear• Induction Hardened, Ground and Polished Worm• Annealed Cast Iron Housing, Precision Machined for Accurate Shaft Alignment• Ball Bearings on Input Shaft Front and Back• Tapered Roller Bearings on Output Shaft• High-Strength, Heat Treated Input and Output Shafts• Flange for Face-Mounting NEMA 143 Frame Motor
Output Options:• Available with 3 Shaft Extensions - L, B, R
Ø.406 -4 HOLES
3/16 X 3/32 ST’D KEYWAY
1/4 X 1/8 ST’D KEYWAY
Ø .8775
.8765
Ø 4.5020
4.5005
Ø .406 - 4 HOLES Ø 5.875 BOLT CIRCLE
RATIO 10 12 20 24 30 40 48 60
OUTPUT SPEED, RPM 172.5 143.7 86.25 71.87 57.5 43.13 35.94 28.75
HP IN 3.36 2.96 2.00 1.72 1.45 1.15 0.99 0.80
HP OUT 3.06 2.65 1.69 1.42 1.14 0.84 0.69 0.52
TORQUE OUT, IN.-LBS. 1119 1164 1236 1243 1248 1235 1208 1138
Overhung Load on Output Shaft, 1000 lbs. at 1.25 in. from Housing or Output CapAll data is for a Service Factor of 1 at 1725 RPM input speed
RATIO 10 12 20 24 30 40 48 60
OUTPUT SPEED, RPM 172.5 143.7 86.25 71.87 57.5 43.13 35.94 28.75
HP IN 3.36 2.96 2.00 1.72 1.45 1.15 0.99 0.80
HP OUT 3.06 2.65 1.69 1.42 1.14 0.84 0.69 0.52
TORQUE OUT, IN.-LBS. 1119 1164 1236 1243 1248 1235 1208 1138
RIGHT ANGLE GEAR REDUCERS C70 LGHS
Dimensions and Ratings
18
HS Style Structural & Design Features:• Right Angle Worm-Gear Reducer • Heavy Duty• Forged Manganese Bronze Worm-Gear• Induction Hardened, Ground and Polished Worm• Annealed Cast Iron Housing, Precision Machined for Accurate Shaft Alignment• Ball Bearings on Input Shaft Front and Back• Tapered Roller Bearings on Output Shaft• High-Strength, Heat Treated Input and Output Shafts• Larger Internal Diameter Output Shaft for Higher Overhung Load Rating• Flange for Face-Mounting NEMA 56C Frame Motor
Output Options:• Available with 3 Shaft Extensions - L, B, R
Overhung Load on Output Shaft, 1000 lbs. at 1.25 in. from Housing or Output CapAll data is for a Service Factor of 1 at 1725 RPM input speed
Ø.406 -4 HOLES
3/16 X 3/32 ST’D KEYWAY
1/4 X 1/8 ST’D KEYWAY
Ø .627
.626Ø
4.5020 4.5005
Ø .406 - 4 HOLES Ø 5.875 BOLT CIRCLE
419/885-3769 • Fax 419/885-3799 • www.toledogear.com
RIGHT ANGLE GEAR REDUCERS C70 LHL
Dimensions and Ratings
19
HL Style Structural & Design Features:• Right Angle Worm-Gear Reducer• Forged Manganese Bronze Worm-Gear• Induction Hardened, Ground and Polished Worm• Annealed Cast Iron Housing, Precision Machined for Accurate Shaft Alignment• Ball Bearings on Input Shaft Front and Back• Tapered Roller Bearings on Output Shaft• High-Strength, Heat Treated Input and Output Shafts• Extended End Bells on Output Shaft for Long Shaft Requirements and Bearing Supports• Flange for Face-Mounting NEMA 56C Frame Motor
Output Options:• Available with 3 Shaft Extensions - L, B, R
RATIO 10 12 20 24 30 40 48 60
OUTPUT SPEED, RPM 172.5 143.7 86.25 71.87 57.5 43.13 35.94 28.75
HP IN 3.36 2.96 2.00 1.72 1.45 1.15 0.99 0.80
HP OUT 3.06 2.65 1.69 1.42 1.14 0.84 0.69 0.52
TORQUE OUT, IN.-LBS. 1119 1164 1236 1243 1248 1235 1208 1138
Overhung Load on Output Shaft, 650 lbs. at 1.25 in. from Housing or Output CapAll data is for a Service Factor of 1 at 1725 RPM input speed
Ø.406 -4 HOLES
1/4 X 1/8 ST’D KEYWAY
Ø .627
.626Ø
4.5020 4.5005
Ø .406 - 4 HOLES Ø 5.875 BOLT CIRCLE
Ø 6.503/16 X 3/32 ST’D KEYWAY
Ø 1.000
.999
RIGHT ANGLE GEAR REDUCERS U-50 RS
Dimensions and Ratings
20
U-50 Style Structural & Design Features:• Right Angle Worm-Gear Reducer• Forged Manganese Bronze Worm-Gear• Induction Hardened, Ground and Polished Worm• Annealed Cast Iron Housing, Precision Machined for Accurate Shaft Alignment• Ball Bearings on Input Shaft Front and Back• Tapered Roller Bearings on Output Shaft• High-Strength, Heat Treated Input and Output Shafts
Output Options:• Available with 3 Shaft Extensions - L, B, R
RATIO 20 40 60
OUTPUT SPEED, RPM 86.25 43.13 28.75
HP IN 1.00 0.62 0.43
HP OUT 0.87 0.43 0.26
TORQUE OUT, IN.-LBS. 625 620 580
Overhung Load on Output Shaft, 780 lbs. at 1.25 in. from Housing or Output Cap
Other Ratios available upon request
All data is for a Service Factor of 1 at 1725 RPM input speed
Ø .41 -4 HOLES
Ø .625
.624
419/885-3769 • Fax 419/885-3799 • www.toledogear.com
RIGHT ANGLE REDUCERS/DC Motor Frame CE34
Dimensions and Ratings
21
CE Style Structural & Design Features:• Right Angle Worm-Gear Reducer• Bronze Worm-Gear• Induction Hardened, Ground and Polished Worm• Aluminum Housing, Precision Machined for Accurate Shaft Alignment• Ball Bearings on Input Shaft Front and Back• Ball Bearings on Output Shaft• High-Strength, Heat Treated Input and Output Shafts• Flange for Face-Mounting DC Frame Motor
Output Options:• Available with 3 Shaft Extensions - L, B, R
RATIO 8 14.5 20 40 60
OUTPUT SPEED, RPM 375 206.9 150 75 50
HP IN 0.96 0.67 0.44 0.25 0.14
HP OUT 0.89 0.58 0.37 0.18 0.09
TORQUE OUT, IN.-LBS. 149 177 153 153 114OVERHUNG LOAD, OUTPUTAT 2 IN. FROM HOUSING, LBS. 36 53 64 92 110
All data is for a Service Factor of 1 at 3000 RPM input speed
Ø.281 THROUGH COVER PLATE 1/4-20 TH’D X .60 DEEP IN HOUSING 4 HOLES
NOTE: OTHER OUTPUT SHAFTCONFIGURATIONS ARE AVAILABLE
To order indicate Model,Output Shaft Extensionand Ratio, as shown below
Dimensions and Ratings
22
RIGHT ANGLE REDUCERS/DC Motor Frame L60 CL Style Structural & Design Features:• Right Angle Worm-Gear Reducer• Bronze Worm-Gear• Induction Hardened, Ground and Polished Worm• Annealed Cast Iron Housing, Precision Machined for Accurate Shaft Alignment• Ball Bearings on Input Shaft• Tapered Roller Bearings on Output Shaft• High-Strength, Heat Treated Input and Output Shafts• Flange for Face-Mounting DC Frame Motor
Output Options:• Available with 3 Shaft Extensions - L, B, R
To order indicate Model,Output Shaft Extensionand Ratio, as shown below
RATIO 5.5 10 14.5 20 30 40 61
OUTPUT SPEED, RPM 314 172.5 118.97 86.25 57.5 43.12 28.28
HP IN 1.31 1.14 0.90 0.69 0.47 0.42 0.27
HP OUT 1.19 1.00 0.75 0.54 0.33 0.27 0.14
TORQUE OUT, IN.-LBS. 239 367 401 401 367 399 332
Overhung Load on Output Shaft, 400 lbs. at 1.00 in. from Housing or Output CapAll data is for a Service Factor of 1 at 1725 RPM input speed
.1895
.1875
419/885-3769 • Fax 419/885-3799 • www.toledogear.com
Dimensions and Ratings
23
RIGHT ANGLE REDUCERS/DC Motor Frame L60 DD Style Structural & Design Features:• Right Angle Worm-Gear Reducer• Bronze Worm-Gear• Induction Hardened, Ground and Polished Worm• Annealed Cast Iron Housing, Precision Machined for Accurate Shaft Alignment• Ball Bearings on Input Shaft• Tapered Roller Bearings on Output Shaft• High-Strength, Heat Treated Input and Output Shafts• Flange for Face-Mounting DC Frame Motor
Output Options:• Available with 3 Shaft Extensions - L, B, R
To order indicate Model,Output Shaft Extensionand Ratio, as shown below
RATIO 5.5 10 14.5 20 30 40 61
OUTPUT SPEED, RPM 314 172.5 118.97 86.25 57.5 43.12 28.28
HP IN 1.31 1.14 0.90 0.69 0.47 0.42 0.27
HP OUT 1.19 1.00 0.75 0.54 0.33 0.27 0.14
TORQUE OUT, IN.-LBS. 239 367 401 401 367 399 332
Overhung Load on Output Shaft, 400 lbs. at 1.00 in. from Housing or Output CapAll data is for a Service Factor of 1 at 1725 RPM input speed
![[3] involuteΣ Worm Gear Design System · [3] involuteΣ Worm Gear Design System Fig. 3.1 involuteΣ Worm Gear Design System 3.1 Introduction The involuteΣ Worm Gear Design System](https://static.fdocuments.in/doc/165x107/5eadff0184c9a55408434a64/3-involute-worm-gear-design-3-involute-worm-gear-design-system-fig-31.jpg)
