Construct the rear cone using the tab. Insert the

cone into the turbine stator using the tabs

INSTRUCTIONS

STEP ONE

STEP TWO

STEP FIVE

STEP THREE STEP FOUR

Use the straw to act as the central support for your engine. Pop out the internal pieces and lay them out in the order shown below.

Roll up the compressor and use the tab to secure it. Then slide it carefully through the turbine support, glueing

the tabs down to hold it in place

Once the turbine support is attached glue the

Compressor to the Turbine.

Construct the turbine by rolling it up. Use the tabs of the turbine stator to keep the shape of the turbine.

Roll up the cone then glue the tab, but don’t stick it to the moveable vanes – or else it won’t turn. You should only attach it to the straw.

You should now have the engine’s internal parts constructed.

It’s time to add the all-important fan blades. Just pop them out and slot them into the nose cone as shown below.

Wrap the fancase around the moveable vanes and the turbine support. Make sure the fancase is the right way round, the end with the slots should be at the back of the engine.

Build your own 3D Trent engine 1

instructions

Step oneFind a pencil, biro or straw to act as the central support for your engine. Pop out the internal pieces and lay them out in the order shown below.

TurbineCompressorNose Cone OGV A-Frame Turbine

StatorRear Cone

Straw orPencil

Step twoYou should now have the engine’s internal parts constructed.

Step threeIt’s time to add the all-important fan blades. Just pop them out and slot them into the nose cone as shown below.

Step four Now join the fancase using the tabs. Make sure the fancase is the right way round, the end with the slots should be at the back of the engine.

Fancase

Nose Cone

FanBlades

Step veYou’re nearly there! Carefully push cowling over the engine, easing the tabs from the OGV and A-frame into slots. Then slide on the rear cowling and turbine stator in the same way.

OGV A-Frame Turbine Stator

FrontCowling

RearCowling

Construct the rear cone using the tab.

Roll up the compressor and use the tab to secure it. Then slide it carefully through the A-frame, using the tabs to

hold it in place.

Roll up the cone, but don’t stick it to the OGV – or else it won’t turn. You should only attach it to the pencil, biro or straw.

Construct the turbine by rolling it up and using the tabs to keep the shape.

Turbine

Once the A-Frame is attached glue the

Compressor to the Turbine.

You’re nearly there! Carefully push the cowling over the front of the fancase. Glue the front fancase tabs onto the front cowling and the rear fancase tabs onto the rear cowling. Then slide on the rear cowling in the same way.

FANCASE

FRONTCOWLING

REARCOWLING

NOSECONE

NOSECONE

MOVEABLEVANES

Their purpose isto channel the air

COMPRESSOR/ COMBUSTOR

TURBINESUPPORT

TURBINE TURBINESTATOR

REARCONE

STRAW

FANBLADES

FANCASE

Bend the moveable vanes towards the centre of the engine

BUILD YOUR OWN 3D TRENT ENGINE 1

REARCOWLING

FRONTCOWLING

GLUE

GLUE

GLUE

FAN CASE

FRO

NT

BA

CK

BUILD YOUR OWN 3D TRENT ENGINE 2

GLUE

GLU

E

GLU

EG

LUE

GLU

E

GLU

E

GLU

EG

LUE

GLU

E

FANBLADES

NOSECONE

MOVEABLEVANES

REARCONE

TURBINESTATOR

TURBINESUPPORT

TURBINE

COMPRESSOR

GLU

E

GLU

E

GLU

E

BUILD YOUR OWN 3D TRENT ENGINE 3