920

bizhub PRO 920 - ALL ACTIVE SOLUTIONSJune 2009

Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.

Legal Notice

This document is designed as a diagnostic tool, primarily for Konica Minolta's support personnel, and authorizedservice representatives. Konica Minolta recommends that all service be performed by an authorized servicerepresentative. Users are responsible for seeking advice of a Konica Minolta authorized service representativeregarding the information, opinion, advice or content of this document.

USER AGREES THAT USE OF THIS DOCUMENT IS AT USER'S SOLE RISK AND THAT THIS DOCUMENT IS PROVIDEDON AN AS IS BASIS WITHOUT WARRANTIES OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUTNOT LIMITED TO, WARRANTIES OF TITLE OR IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR APARTICULAR PURPOSE, OTHER THAN THOSE WARRANTIES THAT ARE IMPLIED BY LAW AND INCAPABLE OFEXCLUSION. IN NO EVENT WILL KONICA MINOLTA OR THOSE ACTING ON ITS BEHALF BE LIABLE FOR ANYDAMAGES, INCLUDING, WITHOUT LIMITATION, DIRECT, INDIRECT, INCIDENTAL, SPECIAL, CONSEQUENTIAL ORPUNITIVE DAMAGES ARISING OUT OF YOUR USE OF THIS DOCUMENT.

This document contains information that was exported directly from Konica Minolta's SSDSupport knowledge base. Some solutions may contain hyperlink references which originallycontained links to graphic or text files. If you wish to view these files, you must access thesolutions via SSD CS Expert Support on Konica Minolta's website, www.kmbs.konicaminolta.us.

SSD SUPPORT SOLUTIONS

bizhub PRO 920 Abnormal noise or odor

Solution ID Solution UsageTAUS0701528EN*

Description Abnormal noise, toner spill or F23 code.

Solution CAUSE: The conveyance idler shaftfor recycle toner conveyancefalls off. When thee-clip which fixes the shaft cannot rotate with the shaft, the e-clipgradually scrapes the surrounding shaft surface. The e-clip is detached and the shaft falls off. I f this occurs, toner cannot be output from cleaner and abnormal noise is generated. Since waste toner cannot be collected, excessive loadon thedrum drive system may occur causing the F23 indication. SOLUTION: Nip spacer/B (p/n 56AA1770) wasinstalledbetween the bearing and the spacer to decrease sliding resistance of the e-clip. By doing so, thee-clip rotates with the shaft. Notes : 1.Replace the e-clip with a new one. 2. If the e-clipgroove in the conveyance idler shaft is badly worn, replace the shaft as well (p/n 55VA5703). 3. Refer to attached file for the procedure. Replacement time: approx. 10to 15 minutes. 4. To view a PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at: http://www.adobe.com/products/acrobat/readstep2.html 5. Thecountermeasure has not been applied to the following bizhub PRO 920 machines. SERIAL NUMBERS 57GA00001 - 57GA00069 57GB00001 - 57GB00049 57GE00001 - 57GE00738 57GF00001 - 57GF00449 57GL00001 - 57GL00013 57GN00001 - 57GN00012 57HE00001- 57HE00141


Description Abnormal noise and J72-48 when performing half-fold.

Solution CAUSE:Idling Gear/2 is worn. SOLUTION: Replace the current Idling Gear/2 and associated parts with the improved/modified parts. See attached Parts Modification document fordetails.To view the PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:http://www.adobe.com/products/acrobat/readstep2.html .

2

Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc. June 2009

bizhub PRO 920 Controller - no or slow print, scan failure, garbled data, lockup

Solution ID 4 Solution UsageTAUS0648753EN*

DescriptionSC49-10 upon installation of the print controller.

Solution CAUSE: The IC-203 hard drive must be formatted in TECH REP mode. Note : If unable to access TECH REP mode, power the machine OFF, hold the Utility key and power the machine ON. SOLUTION: Format the IC-203 hard drive.


Description"HTTP 400 Bad Request" error message when trying to browse to the controller via PageScope Web Connectionusing Microsoft® Internet Explorer 7withMicrosoft® .Net Framework 3.0 installed on a Microsoft® Windows XP SP2 workstation.

Solution CAUSE: Bug in controller firmware. SOLUTION: Install minimum version 21-COS0 (IC-203) or 31-COS0 (IC-611) print controller firmware. The firmware files (IC-203 - 27.4MB) or (IC-611 -28.6MB) and corresponding Release Notes are attached. Notes : 1. To view the PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:http://www.adobe.com/products/acrobat/readstep2.html 2. The latest version firmware or system software is also available via the Konica Minolta Download Selector. Access the Selector from SSD Web Support(CS Expert Support) by clicking on 'Download MSDS, Drivers, Firmware and more'. SPECIAL NOTE : Solution contribution by Bob Felch, ESS/SSD


DescriptionIntermittent SC49-01 and/or SC49-04 codes.

Solution PROBABLE CAUSES: 1. The hard drive has failed. Re-flash the IC-203 firmware.Replace the hard drive as needed (p/n 56UAM72000). Note : The latest version firmware or system software is available via the Konica Minolta Download Selector. Access the Selector from SSD Web Support(CS Expert Support) by clicking on 'Download MSDS, Drivers, Firmware and more'. 2. The IC-203 HDD needs to be formatted. Format the IC-203 HDD by performing the following: a.Enter Tech Rep Mode. b.Press IP Hard Disk Format. c.Press IP HDD Format. d.Select ALL and Yes to format. Note : If the machine will not enter Tech Rep Mode, power OFF the machine and power ON while holding the Utility key. SPECIAL NOTE : Solution contribution by Mark D'Attilio, Production Print/SSD


DescriptionUnable to perform Scan to SMB to a Microsoft® Windows Server 2003 domain controller environment.

Solution CAUSE: Printer controller firmware does not support Scan to SMB on a Microsoft® Windows Server 2003 domain controller environment. SOLUTION: Load the below print controller firmware version (or later) to support Scan to SMB on a Microsoft® Windows Server 2003 domain controllers

3



environment. Model/Controller Controller Firmware 1050 PRO series/IC-611 Minimum version 30-CON0 920 PRO/IC-203 Minimum version 20-CON0 SPECIAL NOTE : Solution contribution by Ian Lynch, Production Print/SSD


DescriptionThe administrator password is not working when trying to log in to the controller NIC in Admin mode.

Solution CAUSE: Admin password must be reset. SOLUTION: To reset the Admin Password, perform the following: 1. Enter the Tech Rep mode. 2. Press Admin Mode. 3. Press Admin Password Setting. 4. Enter a new Admin Password, press OK and close.


DescriptionUnable to send scan to E-mail, SMB, or FTP. When the job list, output history, details is checked, the operation indicates cancelled with no details.

Solution CAUSE: A key counter device is installed on the machine, but not activated. A system code update is required. SOLUTION: Install system code version 20_UMU0orlater system code. The latest version firmware or system software is available via the Konica MinoltaDownload Selector. Access the Selector from SSD Web Support (CS Expert Support) by clicking on 'Download MSDS, Drivers, Firmware and more'. SPECIAL NOTE : Solution contribution by Chuck Tripp, Production Print/SSD


DescriptionWhen printing an 11x17 job with MicroPress®, the job fails with an invalid eject count error in the system events log.

Solution CAUSE: Incorrect dipswitch setting. There is an inconsistancy in page counts between the MicroPress® and main body due to the MicroPress®single-counting and the machine double-counting large size paper. SOLUTION: Set dipswitch 4-7to 0 for the bizhub PRO 920 to single count large size paper. IMPORTANT : This issue has been fixed in MicroPress® version 7.0.1.1 and later for the bizhub PRO 1050. Please install the latest version of

4



MicroPress®.The latest versionis available via the Konica Minolta Download Selector. Access the Selector from SSD Web Support (CS Expert Support) byclicking on 'Download MSDS, Drivers, Firmware and more'. SPECIAL NOTE : Solution contribution by Jim Behrends, Production Print/SSD


DescriptionScan to E-mail times out if more than 1 or 2 pages are scanned.

SolutionCAUSE: The NIC speed and duplex settings are incorrect.

SOLUTION: Set the NIC speed and duplex option to match the Network Switch settings of the environment. Note : If this does not work please set the NIC to 100MBps Half Duplex. Leaving the NIC to AUTO Sensing may be problematic.


Description Unable to scan to E-mail using a Microsoft® Exchange Server 2007.

Solution CAUSE:The Microsoft® Exchange Server is not set up correctly. SOLUTION:Please use the attached settings to set up scan to E-mail on the Microsoft® Exchange Server 2007. To viewthe PDF, Adobe Reader® must beinstalled. Adobe Reader® can be downloaded for free from the Adobe® web site at: http://www.adobe.com/products/acrobat/readstep2.html . CAUTION : The following instructions to create an Anonymous SMTP Receive Connector are NOT to be attempted by a technician. They are provided onlyfor use by an EXPERIENCED Microsoft Exchange 2007 Administrator, as failure to follow these instructions in any way may have a detrimental effect onE-mail flow in Exchange 2007. The instructions provided have been tested numerous times and are known to work. They are currently in production usein-house at Konica Minolta and several customer environments. SPECIAL NOTE : Solution contribution by Jim DiSarro, Workgroup/SSD and Mark D'Attilio/Ian Lynch, Production Print/SSD


DescriptionWhen scanning to the hard drive and selecting PDF as the format, the image can not be viewed or retrieved when using the Konica Minolta TWAIN driver withan applicable software application.

Solution CAUSE: The Konica Minolta TWAIN driver does not support PDF. SOLUTION: The Konica Minolta FTP download utility called Scantrip will function properly when selecting PDF and scan to hard drive. This utility allowsdownloading of files from the hard drive to the workstation. Note : Scanning utilities (Scantrip and Scantrip Admin) are posted on the Konica Minolta SEC website: http://sec.kmbs.us/version2/catalog.html .


DescriptionTandem printing not functioning but, tandem copying functions.

Solution CAUSE: Incorrect system code on the IC-203. SOLUTION: For tandem printing to function the IC-203 controller system code must be at version 20 or higher. Note : The latest version firmware or system software is available via the Konica Minolta Download Selector. Access the Selector from SSD Web Support(CS Expert Support) by clicking on 'Download MSDS, Drivers, Firmware and more'. SPECIAL NOTE : Solution contribution by Bob Moeller, Production Print/SSD

5




DescriptionWhen a print job with Per Page selections is sent to a User Box and an interruption (paper jam, paper tray empty or finisher tray full) occurs, the Per Pagesettings are dropped from the print job. The job will complete but without the selected output functions.

Solution CAUSE: System code and print driver update required. SOLUTION: Please download and install IC-203 system code version 21-COT0 and PostScript print driver version 2.9.0.0. The system code and printerdriver are available via the Konica Minolta Download Selector. Access the Selector from the KMBS public site ( http://www.kmbs.konicaminolta.us ) Support& Drivers tab (for the driver) or from SSD Web Support (CS Expert Support) by clicking on 'Download MSDS, Drivers, Firmware and more'. SPECIALNOTE : Solution contribution by Ron Reed, ASG/SSD


DescriptionController drop off from the network for 3- 5 minutes after a print job, and it does not reply to a PING command.

Solution CAUSE: Bug of controller firmware.

SOLUTION: Please use the attached special controller firmware Ver.21-CPL0. Please refer to the attached Release Notes prior to installation. To viewthePDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:http://www.adobe.com/products/acrobat/readstep2.html . IMPORTANT : Please be aware that thefirmware may not be readily available via the Konica Minolta Download Selector as this is a recently releasedfile byKonica Minolta Japan. Normally, the latest version firmware or system software is available via the Konica Minolta Download Selector. The Selector can beaccessed from SSD Web Support (CS Expert Support) by clicking on 'Download MSDS, Drivers, Firmware and more'. SPECIAL NOTE : Solution contribution by KMBT (Japan).


Description Controller drops off network and is unable to print approximately 5 or more times per day.




DescriptionProblem outputting from the AS/400®.

Solution

6



CAUSE: Bug of controller firmware.



Description AIX (UNIX) queue goes down when printing multiple jobs from ChartMaxx® (application).




DescriptionThe PostScript Option is not available after installing the PostScript kit.

Solution CAUSE:The additional 256MB of memory that comes with the PS-503 PostScript kit was not installed. SOLUTION:Install the 256MB memory stick that comes with the PS-503 kit. Note :The memory is installed in the IC-203. SPECIAL NOTE : Solution contribution by Mark D'Attilio, Production Print/SSD


DescriptionIntermittently the machine will not print and the jobs disappear.Machine must be powered OFF/ON to restore functionality.

Solution CAUSE:There is a TCP/IP conflict as some other node has the same TCP/IP address. SOLUTION: Disconnect the Ethernet cable and perform aPING to verify the duplicate address.Change the printer TCP/IP address. SPECIAL NOTE : Solution contribution by Mark D'Attilio, Production Print/SSD


DescriptionUnable to browse to the main body NIC.

Solution CAUSE: The machine has not been rebooted after entering the TCP/IP address for the main body NIC. SOLUTION: Power the machine down and back up again. This will apply the TCP/IP address to the NIC. SPECIAL NOTE : Solution contribution by Ian Lynch, Production Print/SSD

7




Description SC80-45 at power up and unable to upgrade the IC-203 system code.

Solution CAUSE: Unknown anomaly. SOLUTION: Download and install the latest CF files for the IC-203 and manually copy them to the IC-203 CF card. Note : The latest version firmware or system software is available via the Konica Minolta Download Selector. Access the Selector from SSD Web Support(CS Expert Support) by clicking on 'Download MSDS, Drivers, Firmware and more'. SPECIAL NOTE : Solution contribution by Mark D'Attilio, Production Print/SSD

8


bizhub PRO 920 Dirty image - Spots, banding, streaks, smudged or background


DescriptionDark band from front-to-rear, normally on the first print of a run.

Solution CAUSE: The cleaner shaft holders (bearings) for the toner guide brush are seized resulting in improper brush rotation and a loss of ground to the brush.

SOLUTION: Replace the shaft holders front and rear (p/n 55VA 7502 0) and ensure there is a clean path to ground. SPECIAL NOTE : Solution contribution by Chuck Tripp, Production Print/SSD


DescriptionOvertoning, background and a possible intermittent SC46-08 code.

Solution CAUSE: LD1 or LD2 has failed or are mis-adjusted and the image generated by the laser is not being output or is light on the test pages. This will result in alight patch on the drum for toner density adjustment. SOLUTION: Generate a test page in the Service Mode => Image Processing Adjustment => Drum peculiarty => LD1 or LD2 offset adjustment. Adjustboth to the proper density. If unable to adjust to the correct density, replace the write unit (p/n 57AA-6501 for bizhub 600/750 and p/n 57GA-6500 for bizhubPRO 920). SPECIAL NOTE : Solution contribution by Jim Behrends, Production Print/SSD


Description Marks (black lines) on copies.

Solution PROBABLE CAUSES: 1. Cleaning failure or blade flipping due toinsufficient toner coverage. Replace thecleaning bladewith the new-style drum blade (p/n 57GA56011). 2. Cleaning blade is installed 'askew' since there is not enough run-out of thread at the base part of the blade positioning screw.Replace thescrew withthe new-style screw (p/n 56UA55830). SPECIAL NOTE : Solution contribution by Gregg Gallant, Production Print/SSD


Description Toner spill occurs from lower casing of the drum carriage (developing section) after installation of RC-501. Accumulated toner in the developing unit and thelower casing of the drum falls on the guide plate of the transfer/separation unit.

Solution CAUSE: Toner is accumulated in the recycle pipe due to failure of RC-501 recycle pipe installation. SOLUTION: There are two steps to the procedure: 1.Shorten the pipe to the recycle tank (see the photos below). 2.Pinch the recycle pipe with fingers and check the toner clogging. If the toner is clogged in the recycle pipe, clean it (see the attached file for the cleaningprocedure). bizhub PRO 1050 : bizhub PRO 920 : Note : To view the attached document, Microsoft® Excel® or Excel® Viewer must be installed. Excel® Viewer 2003 (9.9MB) can be obtained free fromMicrosoft® at the following URL;http://www.microsoft.com/downloads/details.aspx?FamilyID=c8378bf4-996c-4569-b547-75edbd03aaf0&displaylang=EN .

9


bizhub PRO 920 Dirty image - Spots, banding, streaks, smudged or background


DescriptionFront-to-rear banding.

Solution CAUSE:The paper detecting actuator/B is worn. SOLUTION:Replace the paper detecting actuator/B (p\n 56GA47820). SPECIAL NOTE : Solution contribution by Gregg Gallant, Production Print/SSD

10


bizhub PRO 920 Image blank or solid color


Description Poor copy quality (SC28-01 may also be indicated). Dark streaks lead-to-trail. Background and a halo effect Grayscale copies or prints are light. Black text is fine.

Solution CAUSE:The developing unit has failed or the mylar on the top portion of the developing unit is damaged. SOLUTION: Replace the developing unit (p/n 57GA-3000). Note : SC28-01 may also occur at power up and the code maynotclear. If this is the case, and the developing unit has already been replaced, the HighVoltage Unit/1 (HV1) has failed. Replace High Voltage Unit/1 (p/n 57GA084010) if deemed necessary. SPECIAL NOTE : Solution contribution by Mark D'Attilio, Production Print/SSD


DescriptionBackground, second side only.

Solution CAUSE: The drum potential sensor and/or the drum temperature sensorhas failed. SOLUTION: Replace the failed drum potential sensor (p/n 55VA-2080) and, if needed, the drum temperature sensor (p/n 56GA-2090).


Description Intermittent blank copies when printing or copying.

Solution CAUSE: The HV unit has failed. SOLUTION: Replace the HV unit (p/n 57GA 8401 0). SPECIAL NOTE : Solution contribution by Mark D'Attilio, Production Print/SSD

11


bizhub PRO 920 Image delay, advance, shift or skew


DescriptionWhen sending mixed originals using the scan function (Scan to **), the original direction settings -[Normal] [Upside down] -are not reflected and images arenot rotated as specified (images are output in landscape).

Solution CAUSE: Firmware upgrade required. Example of symptom When scanning A4 and A3 originals specifying [Mixed Original] and original direction [Normal]: Output: SOLUTION: InstallImage control program firmware version 40 or later (bizhub PRO 920) or Image control program firmware version 50 or later (bizhub PRO1050/1050e and PrintCenterProTM 1050/1050plus)and set the software dipswitch 40-7=1. Note : The latest version of firmwareis available via the Konica Minolta Download Selector. Access the Selector from SSD Web Support (CS ExpertSupport) by clicking on 'Download MSDS, Drivers, Firmware and more'. SPECIAL NOTE : Solution contribution from KMBT, Japan.


Description Image is rotated when printing custom sizes.

Solution CAUSE:Rotation for custom sizepaper is enabled by a software switch setting. SOLUTION: To disable rotation for custom size paper, perform the following: 1.Enter Tech Rep Mode. 2. Touch System Input. 3. Touch Software Switch Setting on the next screen. 4.Access software switch 17-7. 5. Touch OFF (0) to disable the rotation function. SPECIAL NOTE : Solution contribution by Bob Moeller, Production Print/SSD

12


bizhub PRO 920 Image failure other than density/color - magnification, blur


Description Background during a copy or print job. Sometimes more background on second side.

Solution PROBABLE CAUSES: 1. Drum temperature sensor assembly failed. Replace the Drum temperature sensor assembly (p/n 56GA-2090). 2. HV1 has failed. Replace HV1 (p/n 57GA 8401 0). SPECIAL NOTE : Solution contribution by Mike McCarthy, Production Print/SSD

13


bizhub PRO 920 Image too light, dark, uneven or wrong color


DescriptionBackground when using heavy stock paper.

Solution CAUSE: The incorrect toner may be installed SOLUTION: Remove the toner bottle and verify it is type TN910 toner (Item #022J). If the toner is the incorrect type, clean the hopper unit and replace thedeveloper (Item #022B) and install the correct toner. SPECIAL NOTE : Solution contribution by Gary Scimeca, Production Print/SSD


DescriptionRandom dark areas on copies/prints at certain times of the day.

Solution CAUSE: The machine is in a location where it is being hit by direct sunlight which is reaching the drum, affecting the images. SOLUTION: Relocate the machine away from direct sunlight. SPECIAL NOTE : Solution contribution by Bob Moeller, Production Print/SSD

14


bizhub PRO 920 Image voids or deletions


DescriptionWhen running 8.5x11R from the RADF or the Platen glass, the lead edge is cut off by ¾-inch and when duplexing the trail edge is cut off ¾-inch when autorotated to 8.5x11 paper.

Solution CAUSE:Auto image rotate is not set properly. SOLUTION:Please perform the following procedure to resolve the auto rotate image problem:1.Enter Admin Mode.2.Press Copier/Printer Setting.3.Press Auto Image Rotate.4.Press ON Always. SPECIAL NOTE : Solution contribution by Mark D'Attilio, Production Print/SSD


DescriptionDF-606, when duplexing 8.5x11R the trail edge is cut off and when copying 8.5x11R from the glass, the lead edge is cut off.

Solution CAUSE: The dust proof glass is out of position. SOLUTION: Remove and reinstall the dust proof glass. SPECIAL NOTE : Solution contribution by Mark D'Attilio, Production Print/SSD

15


bizhub PRO 920 Miscellaneous


DescriptionNVRAM Troubleshooting Procedure used to identify NVRAM problems and and information concerning damaged or missing NVRAM/BRU.

Solution bizhub C250/C252/C300/C350/C351/C450 NVRAM trouble codes (C-D3xx codes) can occur at any time. Mostly these codes happen when updating firmware. A NVRAM Data Restore procedure wasannounced a few months ago to address these codes: Stop, 0, 7, 1, 3, 9, * What this procedure does is take a good image of the NVRAM off the MFP board (created when you performed the NVRAM Data Backup) and restore it tothe NVRAM. There are approximately 30 registers that can be corrupt, so the above procedure may have to be done as much as 30 times. WARNING : If a corrupt NVRAM is suspected, DO NOT perform the NVRAM Data Backup. This will take the corrupt NVRAM image and back it up to theMFP board. If this is done, and the NVRAM is replaced, the corrupt data that was just backed up will be transferred to the new NVRAM. If this is the case,then the NVRAM and MFP board will have to be replaced as a set. Known unrecoverable NVRAM symptoms: 1. Stuck on hourglass screen 2. Incorrect meters 3. When performing the NVRAM restore procedure the codes repeat themselves Note : One thing that has been noticed is these machines seem to be highly susceptible to voltage sags and spikes. It is HIGHLY recommended to install aquality power line conditioner on these machines. Known fixes for various codes: C-D36E and C-E002 – Install Phase 3.01 firmware (H5 or H6 depending on model). If a corrupt NVRAM is suspected, please try performing a Data Clear. This can be found in the Tech Rep mode. CAUTION : All programmed addresses will be cleared. Please backup the address data using PageScope Web Connection to backup the data beforeperforming the Data Clear. If NVRAM replacement is necessary please be aware that the meters may not be transferred and they might be reset to zero. Thisis unrecoverable and the correct meters cannot be input. 8020/CF2002/8031/CF3102 Codes C-3C00 through C-3C40 indicate a corrupt BRU. Codes C-3C50 through C-3C90 indicates a problem with the PWB-C board or the scanner to main body cable. 8050/CF5001/bizhub PRO C500 The NVRAM for the C500 cannot be replaced in the field. The only way to correct a corrupt NVRAM is to send the OACB, NVRAM, and PRCB into KonicaMinolta to be reset. Known defective NVRAM symptoms: 1. Meters or default adjustment values are extremely high. 2. Adjustments do not hold after powering the machine OFF/ON. Note : On the Black and White machines verify that the NVRAM is bad by swapping a good NVRAM from another machine in the same product family. Thiswill save significant time and expense in getting back the machine in working condition. bizhub 200/250/350 Common symptoms when NVRAM replacement may be necessary: 1. Machine not going to ready state. 2. Not printing to a host name with DHCP. 3. Not scanning to E-mail. 4. On startup, abort code 0x0000999a . 5. Abort code 0x00f00b00 . 6. Not printing. 7. Machine rebooting every few minutes. 8. Screen freezing in Konica Minolta logo. 9. Keep losing machine settings when power OFF. bizhub 420/500 Common symptoms when NVRAM replacement may be necessary: Note : First try to flash the machine to the latest firmware before swapping the NVRAM because the firmware fixes many of the following symptoms: 1. Screen freeze in Konica Minolta logo. 2. Fax unit locking up theMFP or not recognized. 3. C-E084 error code. 4. Cannot PING the MFP. 5. C-D203 error code. 6. Display resetting to Japanese. 7. Losing network settings after firmware upgrade. 8. C-E002 error code. 9. Scan to E-mail or FTP. 10. Loss of adjustment data. 11. Total counter is reset. 12. Display TCR adjustment. 13. C-284x error code.

16



bizhub 600/750 Common symptoms when NVRAM replacement may be necessary: 1. Screen freeze in Konica Minolta logo. 2. Cannot recognize document feeder. 3. Error code SC2203 . 7145/7255 Common symptoms when NVRAM replacement may be necessary: 1. Blank screen. 2. Loss of E-mail addresses. 3. Loss of settings. 4. Error code E56-01 . Ordering Procedures Call the SSD Hotline at 800-825-5664, to open a Problem Ticket. IMPORTANT : All requests for NVRAMs must be approved by the SSD Hotline and a problem ticket generated.If a request is received without anestablished problem ticket number the request will be denied. The NVRAM can be ordered via the Online Technical & Special Program order form located within MyKonicaMinolta.com:1. Login to MKM.com.2. Select the Service tab.3. Select Warranty, Repair, & Special Programs (menu at left side of screen).4. Click on Warranty Services & Technical/FOC Programs (in center of screen).5. Select NVRAM/BRU Replacement Program. Updates/Status Call Logistics at 201-934-5339. Notes : a. Refer to the attached RA formand Bulletin Number 5783 for more detail.The bulletin may be a bit out-of-date concerning actual ordering procedures andapplicable models. b. To view a PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:http://www.adobe.com/products/acrobat/readstep2.html . SPECIAL NOTE : Solution contribution by Clinton Marquardt, ESS/SSD and Cesar Jimenez and Ed Bellone, Production Print/SSD


DescriptionWhat Konica Minolta printer drivers will come bundled with Microsoft® Windows Vista™ and what is the release schedule for Vista™-compatible drivers?

Solution Please refer to the Windows Vista™ Hardware Compatibility List for Printers & Scanners. For EFI legacy products that will not receive a Vista™-specific driver, refer to the following statement: "The previous drivers ( System 5/5e-8/8e ) will not work on 64-bit Vista™. However, these drivers will work on the 32-bit version of Windows Vista™ withminor issues." Known issue : Borders and frames around icons and panes within the driver UI may not show up correctly. Notes : 1. If a previous driver was Microsoft® Windows XP WHQL certified, Microsoft® also honors the digital signature (CAT file) on Windows Vista™. 2. The latest print drivers are available via the Konica Minolta Download Selector. Access the Selector from the KMBS public site(http://www.kmbs.konicaminolta.us) Support & Drivers tab or from SSD Web Support (CS Expert Support) by clicking on 'Download MSDS, Drivers,Firmware and more'. 3. The Windows Vista™ Compatibility Legend can be viewed at: http://kmbs.konicaminolta.us/content/support/vistasupport.html 4. Refer to the attached document for a list of Konica Minolta printer drivers that come bundled with Microsoft® Windows Vista™. To view the PDF, AdobeReader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:http://www.adobe.com/products/acrobat/readstep2.html . SPECIAL NOTE : Solution contribution by Bill Ehmke, ESS/SSD and Jim Behrends, Production Print/SSD


DescriptionNVRAM/BRU replacement form.

17



Solution The online NVRAM/BRU Replacement RA/Claim formis referencedin attached Bulletin Number 5783. Notes : 1. AN SSD TICKET NUMBER MUST BE ASSIGNED IN ORDER TO PLACEA NVRAM/BRU ORDER ONLINE. All requests for NVRAMs must be approvedby the SSD Hotline and a problem ticket generated. If a request is received without an established problem ticket number, the request will be denied. 2. To view a PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:http://www.adobe.com/products/acrobat/readstep2.html . SPECIAL NOTE : Solution contribution by Ed Bellone, Production Print/SSD


DescriptionWhat is the user ID and password to access the Machine Manager (Administrator) section of the main body NIC?

Solution The user ID is: admin (lowercase) and the password is: 00000000 . Note : If this password is changed and or forgotten, the main body allows for a new password entry in Tech Rep mode/Admin Setting/Admin PasswordSetting. Enter the new password and press OK. SPECIAL NOTE : Solution contribution by Mark D'Attilio, Production Print/SSD


DescriptionPart number for the RC-501 waste toner collecting box.

SolutionRC-501 waste toner collecting box (p/n 14RTR70700).


DescriptionHow to create a device printer on an AS/400® system using SCS over LAN.

Solution To Create a Device Description on AS/400® to print to KMBS printers perform the following: 1. From the Main Menu under Selection or Command, type: CRTDEVPRT <enter>.2. Change the following to set up the printer (those settings not changed, keep at default): a. Device Description - (name the printer i.e., KMPrinter) b. Device Class - *LAN c. Device Type - 3812 d. Device Model - 1 e. LAN Attach - *IP f. Port number 9100 g. Font Identifier - 011 h. Form Feed - * Autocut i. Manufacturer - *HP5si j. Paper Source (both) - *letter k. Address - (TCP/IP address of the NIC) l. User Define Option - *IBMSHRCNN m. System Driver (hit F4) - *IBMSNMPDRV or *HPPJLDRV if SNMP is disabled in the environment. Note :Vary ON the device to allow attachment. SPECIAL NOTE : Solution contribution by Jim Behrends, Production Print/SSD


DescriptioneCopy™ compatible machine models, firmware and TWAIN drivers list.

Solution Please refer to attached documentation. To view the PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe®

18



web site at: http://www.adobe.com/products/acrobat/readstep2.html . Notes : 1. The latest version firmware is available via the Konica Minolta Download Selector. Access the Selector from SSD Web Support (CS Expert Support) byclicking on 'Download MSDS, Drivers, Firmware and more'. 2. The latest printer drivers are available via the Konica Minolta Download Selector. Access the Selector from theKMBS public site(http://www.kmbs.konicaminolta.us) Support & Drivers tab or from SSD Web Support (CS Expert Support) by clicking on 'Download MSDS, Drivers,Firmware and more'. SPECIAL NOTE : Solution contribution by Cesar Jimenez, Production Print/SSD and Bill Hall, Workgroup/SSD


DescriptionPaper Test requirements.

Solution For initial test the dealer/branch must supply 1000 sheets of the media paper. Once the paper is received the ticket is transferred to ESS. If the initial test does not have any issues then a second test can be done. The dealer/branch must supply enough media to cover 1/3 of a PM cycle. There isa charge involved to cover labor and supplies. The dealer/branch will be notified byESS before the test to communicate the charges. SPECIAL NOTE : Solution contribution by Cesar Jimenez and Ian Lynch, Production Print/SSD


DescriptionCitrix© compatibility.

Solution Please refer to the attached Citrix© compatibility list for additional information.Some products not listed below arelisted in the document.It covers other MFPsand Controllers like the bizhub C350/C353/C253/C203, the bizhub PRO 1050/920, the bizhub 600/750/360/420/500/162/180/210, IC-303 and IC-409. To viewthe PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:http://www.adobe.com/products/acrobat/readstep2.html . IC-202 Tested in both the Citrix© Metaframe™ XP (FR3) and the Citrix© Metaframe Presentation™ Server 3.0 environments with the Microsoft® Office, Microsoft®Excel and Adobe® Acrobat® 6.0 applications loaded. When utilizing the PostScript Visual driver version 1.0.1, the Adobe® PostScript driver version 1.0.0 orthe PCL driver version 1.01 the print controller can be used without restrictions. IC-203 Tested in both the Citrix© Metaframe™ XP (FR3) and the Citrix© Presentation™ Server 3.0 environments with the Microsoft® Word 2003/Excel 2003 andAdobe® Acrobat® 6.0 applications loaded. When utilizing the PostScript Visual driver version 2.0.28, the Adobe® PostScript driver version 2.0.28 or the PCLdriver version 2.0.0, the print controller can be used without restrictions. IC-205 Tested in both the Citrix© Metaframe™ XP (FR3) and the Citrix© Metaframe Presentation™ Server 3.0 environments with the Microsoft® Office, Microsoft®Excel and Adobe® Acrobat® 6.0 applications loaded. When utilizing the GDI driver version 1.00 or the PCL driver version 1.00 the print controller can be usedwith the following restrictions:1. Cancelled print jobs may stay in queue when using the GDI driver.2. The printer icon may disappear when cancelling a print job when using the GDI driver.3. Print jobs may hang when printing from two or more workstations simultaneously using the GDI driver. IC-302 Tested withCitrix© Metaframe™ FR3 on Microsoft® Windows 2000 and 2003 Server, using PostScript version 1.1. Applications tested were Microsoft® Word 2003, Excel 2003 and Adobe® Acrobat® 6. The only restrictions found were that Owner Information functions werenot available. IC-401 Tested in both the Citrix© Metaframe™ XP (FR3) and the Citrix© Metaframe Presentation Server™ 3.0 environments with the Microsoft® Word 2003, Excel2003 and Adobe® Acrobat® 6 applications loaded. Testing has been performed with the PostScript driver version 1.0.

19



The following restrictions: 1. The mixed media function may not be used. 2. Enabling the "Delete pending print jobs at logout" on the Metaframe™ server does not result in the print jobs being deleted. 3. Print job access codes should not be used. IC-402 Tested withCitrix© Metaframe™ FR3 on Microsoft® Windows 2000 and 2003 Server, using PostScript version 1.0. Applications tested were Microsoft® Word 2003, Excel 2003 and Adobe® Acrobat® 6. The following are restrictions that were found: 1. Custom Size setting is not available. 2.Owner Information, Lock Job and Copier store print functions are not available. 3. The client default settings are not saved. IC-405 Tested withCitrix© Metaframe™ FR3 on Microsoft® Windows 2000 and 2003 Server, using PostScript version 2.0. Applications tested were Microsoft® Word 2003, Excel 2003 and Adobe® Acrobat® 6. The only restrictions found were thatMedia Mixed function is notavailable by network printer. IC-611 Tested in both the Citrix© Metaframe™ XP (FR3) and the Citrix© Metaframe Presentation Server™ 3.0 environments with the Microsoft® Office, Microsoft®Excel and Adobe® Acrobat® 6.0 applications loaded. When utilizing the PostScript Visual driver version 1.0.0.7, the PostScript Adobe® driver version 1.0.0.7or the PCL driver version 1.0.1 the print controller can be used with the following restrictions:1. The watermark function will not function when using the PCL driver.2. The PostScript Visual driver is not available with Microsoft® Windows 2003 Server.3. Booklet mode may not function when called within Adobe® Acrobat®. IP-901 Tested withCitrix© Metaframe™ FR3 on Microsoft® Windows 2000 and 2003 Server, using PostScript version 1.1 and 2.1. Applications tested were Microsoft® Word 2003, Excel 2003 and Adobe® Acrobat® 6. The only restrictions found were that Owner Information functions werenot available. bizhub C350 Standard Controller Tested in both the Citrix© Metaframe™ XP (FR3) and the Citrix© Metaframe Presentation Server™ 3.0 environments with the Microsoft® Word 2003, Excel2003 and Adobe® Acrobat® 6 applications loaded. Testing has been performed with the PCL driver version 1.0 with the following restriction:The watermark feature will not be available on a locally installed printer. bizhub 200/250/350 Standard Controller Tested in both the Citrix© Metaframe™ XP (FR3) and the Citrix© Metaframe Presentation Server™ 3.0 environments with the Microsoft® Office, Microsoft®Excel and Adobe® Acrobat® 6.0 applications loaded. When utilizing the PostScript Visual driver version 1.0.1 or the PCL driver version 1.0.2 the printcontroller can be used with the following restrictions:1. The custom paper size setting is not available.2. The default selections made on client workstations will not be reflected on the printer properties screens. bizhub C650/C550/C451/C450/C352/C351/C300/C252/C250 Tested withCitrix© Metaframe™. Applications tested were Microsoft® Word 2003, Excel 2003 and Adobe® Acrobat® 6.No restrictions were found in testing. SPECIAL NOTE: Solution contribution by Jim Behrends, Workgroup/SSD


Description How to configure LDAP access on a Lotus® Notes R5 or R6 server. Performing a LDAP Search using an Anonymous Connection via Lotus Notes. (supportedLDAPVersion) not enabled.

Solution LDAP Production R5/R6 server setup : 1. Edit Notes.ini and add LDAP task. ServerTasks = Router, Replica, Update, Amgr, AdminP, CalConn, Event, Sched, Stats, HTTP, POP3, maps, LDAP. 2. Create a new Configuration document for LDAP to control Anonymous Access. 3. Create a new Configuration doc, call it Allservers in the Group or Server name, then save and close the doc. 4. Now open the Allservers doc. Note that the Basics tab has changed. 5. Select Use these settings as the default for all servers. Note that Group or Server name is now *-Default-. Also there is now an LDAP tab. 6. Click on the fields that you want to be accessible button. 7. Set it to show First Name InternetAddress and LastName only. Do this so only limited info is available. Notes : a. If you upgrade a server from a previous release to Lotus® Domino 6, the LDAP service uses the LDAP anonymous access configuration from the previousrelease. If you create or edit the domain Configuration Settings documents after updating the directory with the Lotus® Domino 6 PUBNAMES.NTF design,the list of attributes allowed for anonymous access include the following attributes (attached - ldap1.pdf)not listed in the previous release: b.The Allservers configuration doc will only affect the servers running LDAP. It will also allow the MFPs to access LDAP without using an authentication

20



account and password. This is the method that all users are using according to Lotus® Incident 1632724. c. Please refer to the attached document for more detail. d. To view the document(s), Microsoft® Word® or Word® Viewer must be installed. Word® Viewer 2003 (11.7MB) can be obtained free from Microsoft® atthe following URL; http://www.microsoft.com/downloads/details.aspx?DisplayLang=en&FamilyID=95e24c87-8732-48d5-8689-ab826e7b8fdf . e. To viewthe PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:http://www.adobe.com/products/acrobat/readstep2.html . SPECIAL NOTE : Solution contribution by Mark D'Attilio, Production Print/SSD


Description Supporting bizhub vCare.

Solution Initial setup documents for vCare support are attached. The attacheddocuments were sent to all the BSCs. This information is for the BSCs only. It does notapply to dealers. Notes : 1. Please be aware that the bizhub C203/C253/C353/C451/C550/C650 support one-way communication. 2. To view a PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:http://www.adobe.com/products/acrobat/readstep2.html . SPECIAL NOTE : Solution contribution by Greg Lantowski, Production Print/SSD


DescriptionHow to print the account data (Account Track, ECM, EKC) counter list from the machine.

Solution To print the data list from the machine, perform the following: 1. Press the [Utility Counter] key.2. Select [06 Administrator Setting].3. Select [01 System Setting]. 4. Select [04 Management List Print]. 5. Select [03 Use Management List]. 6. Select [Copy].7. Select the desired output paper tray.8. Press OK.9. Press [Start]. SPECIAL NOTE : Solution contribution by Ian Lynch, Production Print/SSD


DescriptionHow to remove print drivers from Macintosh® OS X, 10.2x, 10.3x, 10.4x, 10.5x.

Solution Follow the How to remove Macintosh OS X drivers instructions to correctly remove driver files prior to installing a new or updated version of the driver. Thisis highly recommended to avoid driver conflict. Completely deleting\removing the PPD plug-ins for the loading of the driver will NOT overwrite the previous versions. Note : To view a PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:http://www.adobe.com/products/acrobat/readstep2.html . SPECIAL NOTE : Solution contribution by Bill Ehmke, ASG/SSD and Freddie Burnham/Mark D'Attilio, Production Print/SSD


DescriptionWhere is the extra memory for the main body installed?

Solution The main body comes with a 40GB hard drive; 10GB is used for scanning purposes and 30GB is used for Job store. EM-701 is a 256MB Upgrade Memory for Controller (PCL) printing (Item#7640000942) note = '';if (note != ''){ ArrNotes[x] = note;

21



x++; window.document.write(" " + x + " ");} or the PS-503 PostScript 3 Kit with 256MB Memory (Item#15RL)not for the main body. SPECIAL NOTE : Solution contribution by Freddie Burnham, Production Print/SSD


DescriptionPrintgroove-supported printers.

Solution Printgroove-supported Printers Konica Minolta: bizhub PRO 1050/1050P Embedded Full bizhub PRO 920 IC-203 Full bizhub PRO C500/8050 IP-901/IC-302/IC-405 Limited bizhub PRO C500 IC-301 Limited bizhub PRO C6500/6500P IC-303/IC-305/IC-408 Limited bizhub C650 IC-409 Limited 7085 IP-602/IP-602M Limited Xerox©: DocuTech 6100 series DocuSP 4.x Limited Note : The bizhub C650 IC-409 and Xerox© DocuTech 6100 series DocuSP 4.x are now supported with PrintgroovePOD SERVE/GUIDE/QUEUE version1.3.


DescriptionISW error codes list.

Solution ISWERROR CODES Error Code Description Action 01 There is an error in the command to ISW processing unit. Program is not executing normally. Restart from power ON and re-execute the ISW. 1F A program error is detected. Program is not executing normally. Restart from power ON and re-execute the ISW. 41 Input data format error Check the ISW transfer data file.

22



42 Invalid machine name input data Check the ISW transfer data file. 43 Invalid board name input data Check the ISW transfer data file. 81 Input device error such as input timeout. Check that the communication cable between input devices (PC or ISW Tool) is properly connected. C1 Failed to erase flash ROM. (during ISW to image control board) There is an error in the flash ROM on the image control board. Restart from ISW. If the error persists, the life of the image control board flash ROM mayhave expired. Replace the image control board. C2 Failed to write flash ROM. (during ISW to image control board) There is an error in the flash ROM on the image control board. Restart from ISW. If the error persists, the life of the image control board flash ROM mayhave expired. Replace the image control board. Error Code Description Action C3 ROM checksum error. (during ISW to image control board) The checksum result after program writing does not match the ROM checksum data of the ISW transfer data file. Restart from ISW. If the error persists, theISW transfer data file may not be created correctly. C4 Output device error such as output timeout An error was detected in the ISW board targeted at that time. Check the ISW board. E1 Failed to erase flash ROM. (during ISW to printer control board and FNS control board) There is an error in the flash ROM on the printer control board or FNS control board. Restart from ISW. If the error persists, the life of the targeted flash ROM

23



may have expired. Replace the targeted control board. E2 Failed to write flash ROM. (during ISW to printer control board and FNS control board) There is an error in the flash ROM on the printer control board or FNS control board. Restart from ISW. If the error persists, the life of the targeted flash ROMmay have expired. Replace the targeted control board. E3 Communication error between image control board, printer control board, and FNS control board (during ISW to printer control board and FNS control board)

Check the I/F between the image control board and printer control board, or I/F between the printer control board and FNS control board. Error Code Description Action F80-11 Printer Control ISW not written Perform ISW data install F80-21 VIF Control ISW not written Perform ISW data install F80-30 ISW time-out Perform ISW data install F80-31 ISW data error Perform ISW data install F80-32 ISW write error Perform ISW data install F80-40 FNS ISW not written Perform ISW data install F80-41

24



ZU ISW not written Perform ISW data install Note : Please refer to attached Error Codes list. To viewthe PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from theAdobe® web site at: http://www.adobe.com/products/acrobat/readstep2.html . SPECIAL NOTE : Solution contribution by Cesar Jimenez, Production Print/SSD


DescriptionSupport for Account track, Secure print, and User authentication from Unix/Linux environments.

Solution Konica Minolta does not support Account track, Secure print, and User authentication from Unix/Linux environments at this time. The availability of these options for Unix/Linux environments is being considered for future development. Please attachticket to this solution and provide the following information; 1. Product model number(s). 2. Now many products placed or being considered for placement. 3.What "flavor" and version of Unix/Linux operating system. SPECIAL NOTE : Solution contribution by Tony Pizzoferrato, ESS/SSD


DescriptionHow to load a 64-bit driver on a 32-bit Server system (Microsoft® Windows 2003 Server/Vista™).

Solution Please follow this step-by-step procedure and refer to the attached video. 1. Load the 64-bit driver on the client. 2. Load the 32-bit driver on the server and share it out. Note : If you receive a pop-up indicating “COPY ERROR”, setup cannot copy this file. Example: KOZJA_.PP_. This could possibly be a file path lengthlimitation. Try reducing this limitation by pulling out the specific driver needed and placing it on the desktop. 3. From the 64-bit client perform the Run command to connect to the 32-bit server (example: \\11.11.5.33) and press enter. 4. Double-click on the shared out printer. 5. Select printer and then properties. 6. Select the Sharing tab and click on the additional drivers box. 7. Select or check-off the 64-bit (x64) driver to be added to the 32-bit server. 8. Select OK and the 64-bit driver should be pushed up to the server. 9. Check the additional drivers of the client and server to confirm that the x86 (32-bit) and x64 are both installed. Notes : a.This was tested on like versions of 32-bit and 64-bit drivers. b.To viewthis procedure, Apple© QuickTime®should be installed.It can be downloaded for free at http://www.apple.com/quicktime/download/ . SPECIAL NOTE : Solution contribution by Freddie Burnham, Production Print/SSD


Description Can NCR PAPER® be used as copy paper?

Solution NCRPAPER® has only been approved for use in the bizhub PRO C500/920/1050. Konica Minoltarecommends an NCR PAPER® named Xero/Form® II fromAppleton Papers in Wisconsin. Xero/Form® II is a vegetable-based productthat works extremely well. Note : For the bizhub PRO C500 and 920, refer to Bulletin #5349 . For the bizhub PRO 1050 series see Marketing Bulletin #05-GB-014 . To view a PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:http://www.adobe.com/products/acrobat/readstep2.html .

25




DescriptionVellum paper specifications.

SolutionVellum paper is outside of the special paper specifications of the machine therefore specific paper specification can not be provided. The paper may runthough the machine, however Konica Minolta does not support a particular brand of vellum paper. Note : Vellum paper has tendencies to hold a static charge causing the paper to have transfer problems with possible premature wearing of the drum. Thispaper, in some cases is coated, and could possibly lead to premature wearing of the fuser rollers or leave marks on the copies.


DescriptionHow to install the EM-701 on the bizhub PRO 920.

Solution The EM-701 expanded memory (Item#7640000942) note = '';if (note != ''){ ArrNotes[x] = note; x++; window.document.write(" " + x + " ");} is not installed on the bizhub PRO 920; only on the IC-203. The bizhub PRO 920 uses the standard 40GB hard drive for overlays, watermarks and expandedmemory. SPECIAL NOTE : Solution contribution by Freddie Burnham, Production Print/SSD


DescriptionIs GBC® pre-punched paper a supported paper type?

Solution At this time GBC® pre-punched paperis not a supported type. If attempting to run this stock and a jamsoccurs, rotate paper to the 8.5x11R position or rotateimage and run with holes on trail edge. SPECIAL NOTE : Solution contribution by Chuck Tripp, Production Print/SSD


DescriptionCan one-touch addresses be created from the main body NIC?

Solution To configure the main body NIC perform the following procedure: 1. Enter Admin mode. 2. Press Machine NIC Settings. 3. Enter the IP address, subnet mask and gateway. 4. Connect the main body NIC to the Network. 5. Browse to the machine NIC IP address. 6. Select Machine Manager Setting. 7. Enter user name and password, admin, 00000000. 8. Select Scan Transmission Settings. 9. Enter the E-mail data into the Scan to E-mail settings and press Registration. SPECIAL NOTE : Solution contribution by Mark D'Attilio, Production Print/SSD


Description FS-504/FS-602/FS-604, Paper Exit Sensor wiring breaks.

Solution CAUSE: FNS WIRING/1 (CN125) in the paper exit sensor section breakage due to excessive length.

26



SOLUTION: The length of FNS WIRING/1 has been shortenedfrom 85mm to 20mm and is usedin conjunction with the CN125 WIRING extension.Wheninstalling themodified WIRING/1 harness (p/n 15JK90011E), theCN125 WIRING extension (p/n 15JKN12500) must be installed at the same time.Seeattached Parts Modification document for details.To view the PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from theAdobe® web site at: http://www.adobe.com/products/acrobat/readstep2.html . SPECIAL NOTE : Solution contribution by Ian Lynch, Production Print/SSD


DescriptionPrinter driver support for Microsoft® Windows 64-bit operating system.

SolutionThe latest 64-bit printer drivers are available via the Konica Minolta Download Selector. Access the Selector from theKMBS public site (http://www.kmbs.konicaminolta.us ) Support & Drivers tab or from SSD Web Support (CS Expert Support) by clicking on 'Download MSDS, Drivers,Firmware and more'.


DescriptionKonica Minolta Security White Paper.

Solution See Security White Paper for details. Notes : a.To view a PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:http://www.adobe.com/products/acrobat/readstep2.html . b. Also, go to Konica Minolta's bizhub security page, http://kmbs.konicaminolta.us/content/about/bizhubsecurity.html , for more in-depth security information.

SPECIAL NOTE : Solution contribution by Jim Behrends and Mark D'Attilio, Production Print/SSD


DescriptionHow to update firmware on the bizhub PRO 920 (IC-203), bizhub PRO 1050 (IC-611) and bizhub PRO C6500 (IC-303) using the Internet ISW method.

Solution To update firmware using the Internet ISW method (FTP) pleasereview the attached documentation. To view a PDF, Adobe Reader® must be installed.Adobe Reader® can be downloaded for free from the Adobe® web site at: http://www.adobe.com/products/acrobat/readstep2.html . SPECIAL NOTE : Solution contribution by Cesar Jimenez, Production Print/SSD


DescriptionPostScript printer driver for Microsoft® Windows Vista™.

Solution The latest printer drivers are available via the Konica Minolta Download Selector. Access the Selector from theKMBS public site (http://www.kmbs.konicaminolta.us ), Support & Drivers tab, or from SSD Web Support (CS Expert Support) by clicking on 'Download MSDS, Drivers,Firmware and more'. The Windows Vista™ Compatibility Legend can be viewed at: http://kmbs.konicaminolta.us/content/support/vistasupport.html Note : Refer to the attached document for a list of Konica Minolta printer drivers that come bundled with Microsoft® Windows Vista™. To viewthe PDF,Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at: http://www.adobe.com/products/acrobat/readstep2.html

27




DescriptioneCopy™ ShareScan OP step-by-step installation instructions.

Solution Please refer to attached install documentation for the step-by-step procedure and theeCopy™ compatible machine models, firmware and TWAIN drivers list. To view a PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:http://www.adobe.com/products/acrobat/readstep2.html . SPECIAL NOTE : Solution contribution by Cesar Jimenez, Production Print/SSD


Description Special pop-up drivers for Secure Print and User Authentication/Account track settings screen.

Solution Special bizhub 750/600_IC-202 and bizhub PRO 920_IC-203 pop-up PCL drivers are available that allow the Secure Print dialog window to pop-up whenprinting (bizhub 750/600 PCL version 03.00.00.17 for 32-bit Microsoft® Windows 2000/XP/Server 2003 andbizhub PRO 920 PCL version 02.00.0.06 for 32-bitMicrosoft® Windows 2000/XP/Server 2003). To enable the Secure Print pop-up feature; Select [Printer Properties] => [Printing Preferences] => [Output Method] => Secure Print. In the SecurePrint settings window, input some data (single character is OK) into the Secure Print ID field. Select [OK] => then [Apply] to save setting. Notes : 1. The data input into the Secure Print ID will not be listed in the Secure Print ID field when the Secure Print dialog box pops-up when printing. Please inputthe desired Secure Print ID and Password when Secure Print pops-up for printing. 2. These special drivers (as well as Microsoft® Windows 2000/XP/Server 2003 32-bit/64-bit PS(V) drivers) also allow pop-up functionality for Account Trackand User Authentication. 3. The latest print drivers are available via the Konica Minolta Download Selector. Access the Selector from the KMBS public site (http://www.kmbs.konicaminolta.us ) Support & Drivers tab or from SSD Web Support (CS Expert Support) by clicking on 'Download MSDS, Drivers,Firmware and more'. 4.Please see attached documenation for more information. To view a PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for freefrom the Adobe® web site at: http://www.adobe.com/products/acrobat/readstep2.html . SPECIAL NOTE : Solution contribution by Tony Pizzoferrato, ESS/SSD


Description What is the user ID and password to access themain body NIC, Extension for Maintenance?

Solution The user ID is: ce (lowercase) and the password is: 92729272 . SPECIAL NOTE : Solution contribution by Mark D'Attilio, Production Print/SSD


DescriptionWhy are Counter Reader settingsnot being updated?

Solution Wait until the time specified in order to receive the Counter information. If the Net Care Serveris shutOFF or not on the network at the set time of DataAcquisition, Counter Reader data will not be updated. The update will only occur at the set time. If the Net Care PC is not on the network or turnedOFF at thespecified time an update will not automaticaly occur the next time the Netcare Serveris available on the network. SelectCounter Reader=> Server Setttings => Time of Acquistion; the time is set by Military Time. The time can only be set hourly.


Description What are the power requirements for the bizhub PRO 920?

Solution The bizhub PRO 920 requires 208V AC - 240V AC, 17.6A, 60HZ (dedicated line). Please see attached documentation for additional detail. To view a PDF,Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:

28



http://www.adobe.com/products/acrobat/readstep2.html .


DescriptionCountermeasure against toner spill - developing suction cover modification.

Solution The bizhub PRO 920 developing unit has been modified to reduce toner spill.To update field units to the currentversion install the items listed in attachedBulletin Number 5683. To view a PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:http://www.adobe.com/products/acrobat/readstep2.html . SPECIAL NOTE : Solution contribution by Chuck Tripp, Production Print/SSD


Description Why, even after disabling the IPP port, can itstill be detected as an open port when scanned by port scanning software?

Solution The IPP disable function only disables the IPP print function, not closing the port itself. If port scan is done byusing any port scan software, the IPP port willbe indicated as an open port even after disabling the IPP print function.Of course, no IPP print can be made after disabling it. Note :The next generation modelswill close the IPP port itself by disabling the IPP function.


DescriptionHow to set up FTP Publishing Services on a Microsoft® Vista™ workstation.

Solution Please follow the step-by-step procedures as shown in the attacheddocument. Note : To view a PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:http://www.adobe.com/products/acrobat/readstep2.html . SPECIAL NOTE : Solution contribution by Cesar Jimenez, Production Print/SSD


DescriptionAfter ARPing LinkCom™ III, the LAN light still flashes and is not seen in PrintGuide™.

Solution CAUSE: Incorrect procedure. SOLUTION: After ARPing the LinkCom™ box, PING the TCP/IP address in order to activate the ARP. The light will go solid and it will be seen inPrintGuide™. SPECIAL NOTE : Solution contribution by Paul Santangelo, ESS


DescriptionWhy, when inserting multiple pages from Post Inserter and attempting to subset staple, are all sheetsstapled? For example, if attempting to insert 3 sheetsinto a document and setting only the first 2 to staple, all 3 will be stapled.

Solution It is not possible to apply subset finishing properties to a group of inserts, as the inserts themselves are a subset. SPECIAL NOTE : Solution contribution by Chuck Tripp, Production Print/SSD

29




DescriptionWhatis the item number for the RC-501 kit?

Solution RC-501 Kit (Item #14RU). The Mounting Kit for the bizhub PRO 920 (p/n 57GA-K010)may also be needed. SPECIAL NOTE : Solution contribution by Chuck Tripp and Mark D'Attilio, Production Print/SSD


DescriptionWhen the engine runs out of paper and is not addressed it will cause the writer on the AS/400® to stop.

Solution CAUSE: The writer on the AS/400® times outafter 170 seconds (by default)when MFP runs out of paper. SOLUTION: The following changes to the device description will cause the writing to ignore the time out and just report the error. 1.Pick one of the devices and end the writer and vary the device off.2.Select the option that will allow you to 'Change Device Desc'.3.On the first screen look for the 'Printer error message' parameter and change it to '*INFO'.4.Page down twice and look for the 'User-defined options' parameter it should read '*IBMSHRCNN'; under thisadd ERRMSGINFO.5.Start the writer and vary the device on and test.These changes must be done for the other device on the AS/400®. SPECIAL NOTE : Solution contribution by Paul Santangelo, ESS/SSD


DescriptionRC-501, installation caution.

Solution CAUTION : To prevent the possibility of the RC-501 waste toner hose from becoming plugged with toner, the following should be performed: Inspect the routing of the hose from the machine to the toner collection container. The hose should be in a straight path downwardfrom the machine to thecollection container with no loops that will force the waste toner to travel in an upward direction. If necessary, cut the hose to remove excess length sothatthere is a straight downward path from the machine to the collection container. Also inspect the hose and insure that it is not clogged with waste toner. SPECIAL NOTE : Solution contribution by Bob Moeller, Production Print/SSD


DescriptionHow to find/display a MAC address.

Solution To find the MAC address of a specific device in a Microsoft® Windows environment, such as a main body internal NIC, access the command prompt,PINGthe TCP/IP address of the device and then perform the command, arp –a . The attached procedures are for Microsoft® Windows 98/NT/2000/2003/XP, DOS/Microsoft® Windows 3.11/Microsoft® Windows for Workgroups, Microsoft®Windows Vista™ and Macintosh® OS X. To viewa PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe®web site at: http://www.adobe.com/products/acrobat/readstep2.html . Note : Also attached is the Technitium MAC Address Changer© freeware program. This software is not supported by Konica Minolta and is to be used atyour own risk. To open the ZIP file, WinZip® should be installed. WinZip® can be downloaded from the WinZip® website: http://www.winzip.com/ddchomea.htm . The filecan either be saved to disk or opened. It is recommended to download the ZIP and open from the local computer to view or run. SPECIAL NOTE : Solution contribution by Cesar Jimenez and Freddie Burnham, Production Print/SSD


DescriptionClaw assembly part number.

Solution Claw Assembly(p/n 55VA29013). SPECIAL NOTE : Solution contribution by John Miller, Workgroup/SSD

30




DescriptionHowto change the properties of the job via Job Spooler.

Solution The properties of a job can not be changed via Job spooler. SPECIAL NOTE : Solution contribution by Mark D'Attilio, Production Print/SSD


DescriptionWhen recalling and printing a job that has been stored on the HDD while being output, "Memory overflow" erroris indicated and the job cannot be output.

Solution CAUSE: If data volume of the stored image is too large toaccess the extension memory area, memory overflow occurs. Data volume tends to become largeespecially if the size of image is large, Photo modeis selected and/or the Background is adjusted. Memory overflow also tends to occur with 1-2 modebecause the machine needs to prepare an image of two pages before outputting. SOLUTION: Setdipswitch 10-0 to 1 and 10-1 to 1. Theextension memory area is now enlarged to the maximum size (210MB). SPECIAL NOTE : Solution contribution by KMBT (Japan).


DescriptionHow to change the Page Size in Adobe® Acrobat® in Macintosh® OSX 10.5.

Solution To change the Page Size in Adobe® Acrobat® in Macintosh® OSX 10.5: 1. With the document open, select File. 2. Select Page Setup. 3. Format For: Select the printer from the list. 4.Page Size:Select the desired page size. 5. SelectOK. SPECIAL NOTE : Solution contribution by Gregg Gallant, Production Print/SSD


DescriptionField tips, problems printing with Adobe® Acrobat® 8.x.

Solution For details, see attached file "Problems when PDF output with Acrobat 8.x". To viewthe PDF, Adobe Reader® must be installed. Adobe Reader® can bedownloaded for free from the Adobe® web site at: http://www.adobe.com/products/acrobat/readstep2.html . SPECIAL NOTE : Solution contribution by KM Europe (BEU).


DescriptionSecurity features.

Solution Please refer to attached matrix to view the various security features. Features included: User Authentication HDD Encryption

31



Automatic Job Erase (Temporary Data Overwrite) HDD Sanitizing (Overwrite all data) Hard Drive Lock SSL (HTTPS) IP Filtering Port and Protocol Control Protection from Virus/Worms Secure Print Scan Data Encryption SMTP Authentication POP3 Before SMTP APOP Authentication User (Network) Authentication ISO 15408 Certification Copy Protect Notes : a.To viewthe PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:http://www.adobe.com/products/acrobat/readstep2.html . b. For more in-depth security information, please go to Konica Minolta's bizhub security page,http://kmbs.konicaminolta.us/content/about/bizhubsecurity.html .


DescriptionISO 15408 certification information.

Solution TheMFPsare certified ISO 15408 EAL Level 3. Refer to the following for more detailed information concerning ISO 15408 as well as the attached SecurityWhite Paper.1. ISO 15408 FAQ 2. Trusted Computing Base 3. ISO 15408-3 4. Common Criteria Notes : a. To view a PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:http://www.adobe.com/products/acrobat/readstep2.html . b. Also, go to Konica Minolta's bizhub security page, http://kmbs.konicaminolta.us/content/about/bizhubsecurity.html , for more in-depth security information.


Description MSDS information for drum, developer and toner.

Solution Attached are the Material Safety Data Sheets for the bizhub PRO 920/950 drum, developer and toner. Notes : 1. To open the ZIP file, WinZip® should be installed. WinZip® can be downloaded from the WinZip® website: http://www.winzip.com/ddchomea.htm . Thefile can either be saved to disk or opened. It is recommended to download the ZIP and open from the local computer to view or run. 2. To view a PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:http://www.adobe.com/products/acrobat/readstep2.html . 3. The MSDS documentation is also available via the Konica Minolta Download Selector. Access the Selector from the the KMBS public site (

32



http://www.kmbs.konicaminolta.us ) Support & Drivers tab or from SSD Web Support (CS Expert Support) by clicking on 'Download MSDS, Drivers,Firmware and more'.


DescriptionTroubleshooting Guide, bizhub PRO 920.

Solution The attached bizhub PRO 920 Troubleshooting Guide contents include: 1. Process2. Main Body Mechanical3. Option Mechanical FS-604 FS-509 FS-516 ZU-601/ZU-602 PK-503/PK-504/PK-505 4. Electrical Operation Board Print Control Board ADU DB LU Driver Board 5. ICP List6. Special ROM list7. Controller Special Driver Note : To viewthe PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:http://www.adobe.com/products/acrobat/readstep2.html . SPECIAL NOTE : Solution contribution by KMBT (Japan).


DescriptionInstallation of Z-fold unit on the main body is difficult.

Solution CAUSE: The height of the pin of the main installation stay and the groove on the Z-fold Unit are not even. SOLUTION: Install ZU-601/ZU-602 in the main body while lifting it upward by grasping the stay as shown in the picture. Refer to the attached document for aclose-up view. To viewthe PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:http://www.adobe.com/products/acrobat/readstep2.html . SPECIAL NOTE : Solution contribution by KMBT (Japan).


DescriptionFront door of Z-fold Unit and Finisher does not shut properly (magnet attachment does not hold).

Solution CAUSE: Position of magnet catch and magnet hold plate are not adjusted correctly. SOLUTION: Order two magnet hold plates (p/n 300011191). Install one additional plate to the position where the one plate is currently installed. Order fourflat washers (p/n 00Z61040). Insert two washers for each screw and fix them on the backside of the actuator with screws.Please refer to attached documentfor location. To viewthe PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:http://www.adobe.com/products/acrobat/readstep2.html . Note : Two magnet hold plates and a new actuator have been enclosed for newer ZU-601/ZU-602. Length from the bending part has been elongated for thenew actuator. Therefore insertion of flat washer is not necessary. Serial number cut in of the modified units: 15KW00203/15KV00501/15KT00001 . SPECIAL NOTE : Solution contribution by KMBT (Japan).


Description

33



How to archive a file from a MicroPress® 7/7.5/8 system.

Solution To archive a file from a MicroPress® 7/7.5/8 system, perform the following:1. From MicroPress®, highlight the file that is to be archived.2. From the MicroPress® toolbar, press the Archive button. This will bring up a dialog box which prompts for a destination to save the file.3. Select a location to save the file and select OK. The file will then be saved with an MSM extension. This is the archive format used by MicroPress®. The fileis then portable and can be "unarchived" on the same or another system. Job settings will be saved with the file. Note : Archiving is the method thatSSD requires if a file needs to be submitted for testing. SPECIAL NOTE : Solution contribution by Chuck Tripp, Production Print/SSD


DescriptionWhat is the length of the power cord?

SolutionThe power cord is approximately 9' 8" in length.


Description Preventing the write from crashing on the AS/400®.

Solution In order to prevent the write from crashing on the AS/400® read the following IBM bulletin. Timeout Settings in the Operating System Printer Device Description Settings in the printer device configuration in operating system that can cause writers to end are the Inactivity timer and Activation timer. The recommended setting for Inactivity timer should be set at some value other than *NOMAX so that the connection will be closed during periods of noactivity. Even if not sharing on the network, *NOMAX can cause problems with the writer connection. The Activation timer should be set to a value large enough to prevent posting of intervention errors due to TCP/IP transmission delays and printer processingdelays. The default setting of 170 seconds is usually large enough to accomplish this unless you send large files to a printer with a slow processor that has alot of memory. Increasing the activation time will prevent unwanted intervention errors but that time will have to pass before you will get a desired interventionerror. Note that intervention errors do not stop the print process. If the Printer Error Message parameter in the Device Description for the writer was set to *INQ ,then the intervention will require an operator input to retry or to cancel the writer. (At R370, the Printer Error message is not recognized on ASCII printers. Change the User defined options parameter to ERRMSGINFO ). If the Printer Error Message parameter was set to *INFO , then the driver will continue to retry until the connection has been established or the TCP/IP hasclosed the socket or, in the case of a slow printer processor, the proper response is obtained which is either the printer is on-line or that the printer hasreceived all the data. If the connection was eventually successful, the intervention message will be attempted to be removed from the message queue, andprocess will continue. Please set the Printer Error Message to *INFO and the User Defined options to ERRMSGINFO. SPECIAL NOTE : Solution contribution by Paul Santangelo, ESS/SSD


DescriptionHow to change the Power Save Settings (Low power Mode or Sleep Mode).

Solution To change the Power Save Settings: 1. Utility /Counter. 2. Administrator Settings. 3. Password. 4. OK. 5. System Settings. 6. Power Save. 7. Specify the Power Save Mode or Sleep Mode that needs to be to changed. 8. Select the interval of time that must elapse before turning on automatically. 9. OK.

34



SPECIAL NOTE : Solution contribution by Marge McLea, Production Customer Support/SSD


DescriptionPower consumption data.

Solution To view power consumption data for warm-up, standby, and running modes, see the attachment. Note: To view a PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:http://www.adobe.com/products/acrobat/readstep2.html SPECIAL NOTE: Solution contribution by Clinton Marquardt, ESS/BSE


Description How to change annotation settings in the stamp/image overlay application.

Solution To set up the annotations settings, perform the following:1. Press the Utility key.2. Select Administration Setting.3. Select System Setting.4. Select number 10 Annotation Settings.


DescriptionWhat steps need to be performed when replacing the NVRAM?

Solution Please perform the following after replacing the NVRAM: 1. Enter [Utility menu] by pressing the [Utility/counter] button. 2. Enter [Touch Panel Adjust] mode by pressing [5] of the hard buttons. 3. Adjust the touch panel. 4. Return to [Utility menu] by pressing [1] of the hard buttons. 5. Enter Service Mode. 6. Perform each setting in [System Input]. 7. Perform each adjustment in [Process]. 8. Perform each adjustment in [Machine Adjust]. 9.Power machine OFF/ON. SPECIAL NOTE : Solution contribution by Clinton Marquardt, ESS/SSD


DescriptionHow to set the finisher sub tray as the default tray.

Solution Note : This will not function with image control firmware below version 20. To set the finisher sub tray as the default tray: 1. From the basic screen, touch [Finishing] select [Sub Tray] and touch [OK]. 2. Press the [Utility/Counter] key. 3. Touch #3 [Copier Setting]. 4. Touch #1 [Reset Setting]. 5. Touch # 1[Initial Setting]. 6. Touch Current Setting. 7. Touch OK.

35



8. Touch #2 [Reset Function Setting]. 9. Touch [Auto Reset Key Setting]. 10. Touch [Initial Setting]. 11. Touch [Close] 4 times to return to Basic Screen. SPECIAL NOTE : Solution contribution by Bob Moeller, Production Print/SSD


DescriptionCan envelopes used as a paper source in the bizhub 600/750/920?

SolutionEnvelopesare not a specified paper media for these models.


DescriptionFirmware and system code versions required to support printing from MicroPress® 7.0.

Solution Firmware version 20_ABSO is required on the bizhub 920. System software 70 is required on the IC-203. RAW ports 5 and 6 need to beset for 9201 and9202 configured for thecontroller and software DIPSW 48-1 set to OFF (0). Please see attached setup instructions and support bulletin. Notes : 1. To view a PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:http://www.adobe.com/products/acrobat/readstep2.html . 2. The latest version system software is available on the Konica Minolta Download Selector. Access the Selector from SSD Web Support (CS ExpertSupport) by clicking on 'Download MSDS, Drivers, Firmware and more'.

Solution ID Solution UsageTAUS0701136GE*

DescriptionAre Citrix© certified drivers available?

Solution Citrix© certified drivers are not available. SPECIAL NOTE : Solution contribution by Mark D'Attilio, Production Print/SSD


DescriptionNo paper lift from the second tandem tray on the LS-501/LS-502. No service codes are being indicated, and powering ON/OFF the copier does not clearissue.

Solution CAUSE:Failedfaulty parts feature of the copier. If an error or service code goes un-cleared the copier will automatically isolate the option so copies can bemade without the option. SOLUTION: To clear the issue with the tandem tray, perform the following: 1. Enter the service mode. 2. "Service mode menu screen" Press the [07 System Setting] key. 3. A sub menu appears on the right side of the screen. Press the [01 Software SW Setting] key on the sub menu. 4. "Software switch setting mode screen" Press the [up arrow], [down arrow] key or the numeric keys to select a DIPSW bit number. 5. Press the [On (1)], or [Off (0)] key to set the selected bit number ON/OFF. 6. Set DIPSW 33, bit 7 fromOn (1) to Off (0). 7. Press the [Return] key to return to the "Service mode menu screen" on which the sub menu was displayed.


Description Default HDD lock password information.

Solution Thebizhub PRO 1050 and 920 series have the function to protect HDDdata, which is activated when the security enhance mode is enabled. This function isexplained in the User's Guide (Security). However, the description about the default password (password when machine is shipped from the factory) isincorrect.

36



Default password Wrong: 9-digit main body serialnumber Correct: 9-digit main body serialnumber + 23 space characters However, there was afirmware bugcausing the default password tochange tothe '9-digit main body serial number'.This has been corrected by a firmwarerevision. Therefore, there are cases the default password may have been changed to the '9-digit main body serial number' unintentionally. To change the HDD lock password, input of the default password is required. Basically, it is possible to change the password by inputting the '9-digit mainbody serial number + 23 space characters'. If this password is not accepted, try the '9-digit main body serial number'. CAUTION : After changing the HDD lock password, be careful not to forget the new password. Note : Please ensure that the latest firmware update is installed. The latest version firmware or system software is available via the Konica MinoltaDownload Selector. Access the Selector from SSD Web Support (CS Expert Support) by clicking on 'Download MSDS, Drivers, Firmware and more'. SPECIAL NOTE : Solution contribution by Ron Reed, ESS/SSD


Description It is not possible to make a print-at-onceifa TIFF file was directly printed without using a print driver such as PageScope Direct Print.

Solution CAUSE:The image file was recognized as a custom size original.This occurs due to the bizhub PRO 1050/920 recalculating the image size as 600dpi insteadof using the actual resolution of the TIFF file. SOLUTION: The bizhub PRO 1050/920has a function to calculate the original size of the TIFF image by using the resolution and pixel data in the taginformation. However, it is not enabled as default. Changing the dipswitch settings (below) can enable/disable the function. However, it ONLY canautomatically feed the matchedsize paper when the size was matched exactly in millimeter order. If the size differs 1mm, the machine recognizes it as acustom size and stops. DIPSW42-5 (0): Default setting. Recalculate the size by 600dpi.DIPSW42-5 (1): Uses tagged information of TIFF image to calculate the original size.


DescriptionZU-602, how to flash the finisher.

Solution To flash the finisher, perform the following: 1. Turn the Sub and Main power switches OFF on the main body, and unplug the power cord. 2. Unplug the ZU-602 power cord from the outlet and from theZU-602. 3. Remove the back cover of the ZU-602. 4. Remove the Finisher I/F loopback connector from the wire harness located on the control board. 5. Remove the CN6 (blue) connector on the left side of the board. 6. Connect the Finisher I/F loopback connector to CN6. 7. Plug in the power cords of the main body and the ZU-602. Turn ON the main and sub power switches to run ISW of the Finisher. 8. After ISW runs, turn the sub and main power switches OFF, then replace the Finisher I/F loopback connector to the previous position. 9. Connect the connector to CN6 (blue) on the control board. 10. Install the back cover of the ZU-602. SPECIAL NOTE : Solution contribution by Jim Behrends, Production Print/SSD


DescriptionWhy the Staple function is grayed out on the FS-516 finisher.

Solution If the subtray is selected it will disable (gray out)the finisher functions for staple and punch. SPECIAL NOTE : Solution contribution by Greg Lantowski, Production Print/SSD


Description After specifying a magnification and selecting Inter Sheet mode, the magnification is canceled when a document is placed in the document feeder.

Solution CAUSE: Specification of the Inter Sheet function. When Inter Sheet is selected, AMS is automatically selected. Accordingly, the magnification set before

37



selecting Inter Sheet is now canceled. For example: 1. On the basic screen, specify x0.950 magnification. 2. On the application selection screen, select [Sheet/Cover/Chapter Insert] => [Inter Sheet] => [Front Cover] => [Cover/Blank] then OK. 3. On the basic screen, [Auto x 0.950] is indicated in the magnification field. 4. When a document is placed in the document feeder, the display changes to the magnification that matches the document size and paper size (Automaticmagnification selection). Note : When specified magnification + Inter Sheet mode (set by using above steps 1-3) are stored using Program, the same behavior (step 4) occurs afterrecalling the Program mode setting.

SOLUTION: Select Inter Sheet before setting the magnification. 1. On the Application selection screen, select [Sheet/Cover/Chapter Insert] => [Inter Sheet] and set the desired sheet insertion mode. 2. On the basic screen, specifythemagnification to set. 3. On the basic screen, the magnification is indicated as specified (no indication of Auto). 4. The magnification display does not change when a document isplaced in the document feeder. The document can be copied at the specified magnification. SPECIAL NOTE : Solution contribution by KMBT (Japan).


DescriptionHow to set up an FTP one-touch destination.

Solution To set up an FTP one-touch destination from the main body, perform the following: 1. Press the SCAN key. 2. Press the FTP icon. 3. Press Address Input. 4. Enter the Profiles name, Characters for search, Password, Login, Host Address and File Path. Note : If anonymous is selected there is no need to enter a password and login name. 5. Press register. Note : For step-by-step procedures please see the attached documentation. To viewthe PDF, Adobe Reader® must be installed. Adobe Reader® can bedownloaded for free from the Adobe® web site at: http://www.adobe.com/products/acrobat/readstep2.html . SPECIAL NOTE : Solution contribution by Cesar Jimenez, Production Print/SSD


DescriptionHow to install a printer using LPR (IP Printing) under Macintosh® OS9.

Solution Please perform the procedures mentioned in the attached document. Note : To view a PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:http://www.adobe.com/products/acrobat/readstep2.html . SPECIAL NOTE : Solution contribution by Mark D'Attilio, Production Print/SSD


DescriptionPrinting to a printer on a Microsoft® Windows XP PC from a Macintosh® OS version 10.3.

Solution Please perfrom the step-by-step procedures mentioned in the attached PDF. Note : To view a PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:http://www.adobe.com/products/acrobat/readstep2.html . SPECIAL NOTE : Solution contribution by Cesar Jimenez and Mark D'Attilio, Production Print/SSD


DescriptionWhy, whenusing scan functions (Scan to E-mail, HDD, FTP, SMB, Group), is the "space" and some other special characters"grayed out" on the file name

38



input screen and cannot be used?

Solution "Space" and some other special characters cannot be used for file name due to a limitation on the controller side. This is the functional restriction on thespecification. Unavailable characters: "space" / ; : , \ ("grayed out" on the screen). SPECIAL NOTE : Solution contribution by KMBT (Japan).


DescriptionHard Disk Drive image extracting tool (archive job visualizer).

Solution The format to save image dataon a main body HDD has been changed forintegrated machines (bizhub PRO 1050/1050P and bizhub PRO 920). Imagedatafor conventional models cannot be migrated over to integrated machines and vice versa. Due to this problem, there is a tool to covert image data on aHDD to data which can be handled on the PC. By connecting the built-in HDD in the main body to a PC and performing the batch process with this tool (attached), compressed image data on the HDDisconverted to TIF files which can be handled on a PC. Note : This toolis also available via the Konica Minolta Download Selector (search for 'jv100'). Access the Selector from SSD Web Support (CS ExpertSupport) by clicking on 'Download MSDS, Drivers, Firmware and more'. SPECIAL NOTE : Solution contribution by KMBT (Japan).


DescriptionDF-606, PLEASE LOAD DESIGNATED PAPER 8.5x11 is indicated on the operation panel and paper is loaded in the paper trays.

Solution CAUSE: Improper selectionsare set for the Auto Paper Type. SOLUTION: Perform the following procedure to resolve the paper tray problem: 1. Press the Utility key.2. Press the System icon.3. Press Function.4. Press Feed Tray Setting.5. Press Auto Paper Type Select.6. Ensure the -- is selected above Normal paper. Normal should also be selected. SPECIAL NOTE : Solution contribution by Mark D'Attilio, Production Print/SSD


DescriptionWhat is the I/O code to run the recycle pump motor (M24) used with the RC-501 kit?

Solution The code to run/test the recycle pump motor (M24) in I/O mode is code 54, multicode 2. The code is found under the Peculiar Functions Sectionin the TechRep. Mode section of the Service Manual. SPECIAL NOTE : Solution contribution by Greg Lantowski, Production Print/SSD


DescriptionCan preset paper color names be changed?

Solution Default Paper Color choices names cannot be changed.Other paperscan beregistered with any name the customer would like in tray set-up, but they will allhave to use one of the preset color choices. SPECIAL NOTE : Solution contribution by Chuck Tripp, Production Print/SSD


Description When Tandem copying or printing, are two IC-203s required for proper operation?

Solution Tandem copying or printing will function properly with one or two controllers (IC-203). SPECIAL NOTE : Solution contribution by Mark D'Attilio, Production Print/SSD

39




DescriptionWhat is the part number for the Transfer Separator Corona Unit Separator Assembly?

Solution Transfer Separator Corona Unit Separator Assembly (p/n 57GA-270 0). SPECIAL NOTE : Solution contribution by Chuck Tripp, Production Print/SSD


DescriptionThe incorrectdischarge wire is included in some PM kits.

Solution D57GAPM500 (500 PM Kitforbizhub PRO 920)lot number H4524 contains the incorrect Discharge Wire (p/n 56UA26130). The correct part number for theDischarge Wire is 55VA26130. A replacement spare part is availableFOC. To obtain a FOC replacement, please contact Lisa Piazza at 1-800-456-6422 Ext. 2185 or via E-mail ( [email protected] ). SPECIAL NOTE : Solution contribution by Mahen Shukla, ESS/SSD


DescriptionThereis more than one tray with the same sizepaper andone of the trays must be set as the default ATS/APS tray.

Solution To set default tray for ATS/APS mode: 1.Set tray priorityfor the "default" trayas highest priority: a. Press Utility/Counter key. b. Press Function Setting. c. Press Feed Tray Setting. d. Press Feed Tray Auto. Make sure trays under "ATS/APS Switch" are highlighted andset "Tray Priority" order. Note : Whichever tray is selected as the highest priority will become the default tray when Current is selected. 2. Set Current settings: a. Press Utility/Counter. b. Press Copier Settings. c. Press Reset Setting. d. Press Initial Setting. e. Press Current, then OK. f. Close setting screens. SPECIAL NOTE : Solution contribution by Mike McCarthy, Production Print/SSD


DescriptionWhat is the user name and password needed when performing an engine capture via HyperTerminal?

Solution The user name and password is konicaminolta/12345678. SPECIAL NOTE : Solution contribution by Mark D'Attilio, Production Print/SSD


DescriptionHow to print SAP R/3barcodes.

Solution In order to print SAP barcodes, you need to have the barcode fonts installed on the MFP. This means that you need to purchase SAP compatible barcodefonts and install them onto the HDD of the controller. Currently the best andeasiestway to print SAP barcodes is to attached a device from Typehaus to the MFP. This device has been tested and it complete compatible with SAP barcodes. This device is so sophisticated that you need not configure it with an TCP/IPaddress, it will assume the TCP/IP address of the MFP and intercept the font call for the barcode and replace the call with the actual barcode fonts. Nothingelse will be required. To Purchase this device contactTypehaus at: http://typehaus.com . Be sure to mention your affiliation with Konica Minolta. SPECIAL NOTE : Solution contribution by Paul Santangelo, ESS/SSD

40




Description IsMagneCote® paper or magnetic backed paper supported?

Solution MagneCote® paperor magnetic backed paper is not supported. SPECIAL NOTE : Solution contribution by Marge McLea, ProductionCustomer Support/SSD


DescriptionAdditional information concerning "Custom Size Settings".

Solution In the Konica Minolta PCL driver, the "Custom Size Settings" can only be specified from the printer driver setup dialog box, which can be displayed from the"Printers" window (or "Printers and Faxes" window). Please refer to attached documentation for clarification. To viewthe PDFs, Adobe Reader® must be installed. Adobe Reader® can be downloaded for freefrom the Adobe® web site at: http://www.adobe.com/products/acrobat/readstep2.html . SPECIAL NOTE : Solution contribution by KMBT (Japan).


DescriptionAdditional information concerning PageScope Web Connection.

Solution Additional information for bizhub PRO 920/IC-203 and bizhub PRO 1050 series/IC unit: 1. "Done Job List" maximum number. Maximum is 100 ([Print] and [Scan transmission]). If it exceeds 100, the jobs are deleted from old history. 2. Please note that "Done Job List" is all deleted when the main body poweris turned OFF. Note : Please refer to attached documentation for clarification. To viewthe PDFs, Adobe Reader® must be installed. Adobe Reader® can be downloadedfor free from the Adobe® web site at: http://www.adobe.com/products/acrobat/readstep2.html . Additional information for bizhub 360/420/500/IC-204 and bizhub 600/750/IC-202 1. "Job History" maximum number. Maximum is 100 in all jobs ([Print], [Scan], [Fax TX], [Fax RX] and [HDD/Memory]) total. 2. "Job History" display/non-display setting (after main body poweris cycled OFF/ON). Even if main body power is cycled OFF/ON, "Job History" is not usually deleted. However "Job History" can be set to non-display (data is deleted)by DipSW24-1. DipSw 24-1 0: Display 1: Non-display SPECIAL NOTE : Solution contribution by KMBT (Japan).


Description Improvement in the exchange of the Toner Collection Box.

41



Solution To facilitate the exchange of the Toner Collection Box, Joint Pipe 1assembly and Joint Pipe 2 assembly are available. In accordance with this, Joint Pipe2assembly has been added to the component partsfor the Toner Collection Box.See attached Parts Modification document for details.To view the PDF, AdobeReader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:http://www.adobe.com/products/acrobat/readstep2.html .


DescriptionCan the default file name that is automaticallyassigned to scanned documents (when a file name has not been manually entered in the scan settings) bechanged to a new default name?

Solution This is not an option on the bizhub PRO 920. If this is a desired change please create a ticket by web submission or calling into the SSDHotline. Fill out theattached Product Change Request , scan and attach form to the ticket. To view the document(s), Microsoft® Word® or Word® Viewer must be installed.Word® Viewer 2003 (11.7MB) can be obtained free from Microsoft® at the following URL;http://www.microsoft.com/downloads/details.aspx?DisplayLang=en&FamilyID=95e24c87-8732-48d5-8689-ab826e7b8fdf . SPECIAL NOTE : Solution contribution by Chuck Tripp, Production Print/SSD


DescriptionSerial number and meter reading location.

Solution Serial number : Open left front door. Serial number is on bottom frame (below cooling fan). Meter : Open left front door. Meter is below operation panel. Note : Please see attachment.


DescriptionIs scanning to an external memory device supported?

Solution Scanning to an external memory device is not supported. SPECIAL NOTE : Solution contribution by Mark D'Attilio, Production Print/SSD


DescriptionDF-606, what is the part number for the original reverse sensor (PS309) and the original exit sensor (PS307)?

Solution Original reverse sensorand the original exit sensorhave the same part number (13GA 933 1). The sensor mylar part number is 13GA 4643 0. SPECIAL NOTE : Solution contribution by Chuck Tripp, Production Print/SSD


Description How to configure Scantrip ver 2.2. There is no bizhub PRO 920 to select in the drop-down menu.

Solution Select "SECURED"to set up the bizhub PRO 920 for scan to HDD. SPECIAL NOTE : Solution contribution by Mike McCarthy, Production Print/SSD


42



DescriptionWhich cableconnectsto the CCD unit?

Solution The Parts Manual for the bizhub PRO 920 lists the correct part number as 57GA90561. The part is described as AD wiring.It is actually the CCD cable/wiringconnection. SPECIAL NOTE : Solution contribution by Greg Lantowski, Production Print/SSD


DescriptionOffice Workgroup and Production Print - Basic Functionality Chart (Marketing Bulletin 08_GB_024).

Solution Konica Minolta is pleased to announce a new sales tool called the Office Workgroup and Production Print - Basic Functionality Chart (see attachment). Thischart has been developed to give you a broad overview of the basic functionality on all current Office Workgroup MFPs and Production Print Systems. This ‘at-a-glance’ chart will be helpful to determine product families, standard and optional features, print and scan PPM speeds, copy, print controller, localand network scanning destinations and lastly fax functionality. Models associated with the chart are: bizhub 160, 161f, 181, 200, C203, 250, C253, 350, C353, C353P, 360, 421, C451, 501, C550, 600, C650, 750 andbizhub PRO C5500, C6500, 920, 1050e. This chart will be associated under Support Materials or individual product pages for each model listed on MyKonicaMinolta.com. Note : To viewthe PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:http://www.adobe.com/products/acrobat/readstep2.html .


Description Paper information, set when registering a program job, is not retained.If a program job is registeredwith a specified paper feed tray set with specified paperconditions (size, weight, type of paper), when recalling the job, the tray is selected but the paper conditions set for the tray are cleared. User needs to set thepaper conditions again. For example, if the user sets custom size thick paper (300x210, 150gsm) in Tray 2 and registers a program job with Tray 2 (set with the paper conditions) andsingle-staple mode: Set the paperto use in Tray 2 and select Custom (with manual input of the actual paper size) and Paper weight for Tray 2. On the copy screen, select Tray 2, set the original and select single-staple mode. Press Program (bizhub PRO 920)/Mode Memory(bizhub PRO 1050) key and register the job with an arbitrary name. Then set other paper in Tray 2 and recall the above program job. Tray 2 and single-staple mode are selected, but the paper size and weight informationpreviously set for Tray 2 has changed. If the user copies the job without change, the job is printed on the paper currently set in Tray 2.

Solution CAUSE:This isproduct specification. Note : When registering a program job, only paper feed tray information is stored for paper-related information. Paper size, type and weightis not stored.When the program job is recalled, paper currently set in the specified tray is used. SOLUTION: When recalling a program job, set the paperto use in the specified tray and set the paper conditions again before outputting. SPECIAL NOTE : Solution contribution by KMBT (Japan).


DescriptionThe 500K PM Kit part number.

Solution The 500K PM kit part number listed in the bizhub PRO 920 Parts Catalog (p/n 57GA-PM5 0) or the supply item number (Item #D57GAPM500) are no longervalid.To order the 500K PM Kit, useItem #DA0Y5PM500 for both the bizhub PRO 920 andbizhub PRO950. Please refer to attached Marketing Bulletin#09-GB-013. To viewthe PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:http://www.adobe.com/products/acrobat/readstep2.html . SPECIAL NOTE : Solution contribution by Chuck Tripp and Cesar Jimenez, Production Print/SSD


DescriptionFS-604 control board (FSCB) part number.

43



Solution FSCB (p/n 15SJ-901 0). Note :It is listed as the Control Unit in the Parts Catalog. SPECIAL NOTE : Solution contribution by Chuck Tripp, Production Print/SSD


DescriptionHow to change date and time.

Solution To change date and time: 1. Utility. 2. Administrator. 3. Password. 4. System Setting. 5. Date/Time Setting. 6. Touch the desired key to adjust the time and or date. 7. Use the Key pad to make changes. Note :Daylight Savings Timeis activated by touching Summer Time. This will gain one hour. SPECIAL NOTE : Solution contribution by Marge McLea, Production Customer Support/SSD


Description08XB error when performing an LDAP search.

Solution CAUSE: The Authentication method is not set to SIMPLE. SOLUTION: Set the LDAP Authentication method to SIMPLE on the machine NIC. SPECIAL NOTE : Solution contribution by Mark D'Attilio, Production Print/SSD


Description FS-509/FS-516/FS-604, maximum staple capacity.

Solution Finisher staple capacity: FS-509 = 100 maximum FS-516 = 100 maximum FS-604 = 50 maximum SPECIAL NOTE : Solution contribution by Marge McLea, Production Customer Support/SSD


DescriptionHow to change the Page Size in Adobe® InDesign® in Macintosh® OSX 10.5.

Solution To change the Page Size in Adobe® InDesign® in Macintosh® OSX 10.5: 1. With the document open, select File. 2. Select Print. 3. On the General tab select the printer from the list. 4. On the Setup tab select the desired page size. 5. Select Print to print the job.

44



SPECIAL NOTE : Solution contribution by Gregg Gallant and Mark D'Attilio, Production Print/SSD


Description Pagescope Data Administrator compatibility.

Solution TheMFP is not compatible with Pagescope Data Administrator. SPECIAL NOTE : Solution contribution by John Miller, Workgroup/SSD and Rich Raynor, ASG/SSD


DescriptionHow to enable batch printing.

Solution To enable batch printing, perform the following procedure: 1.Enter Tech rep Mode. 2.Press System Input. 3.Press Software Switch Setting. 4.Go to switch 21-0 and select ON. 5.Go to switch 29-2 and select ON. These switches will enable batch printing and the over-limit check when batch printing. SPECIAL NOTE : Solution contribution by Mark D'Attilio, Production Print/SSD


DescriptionHow to manually adjust the operation panel touchscreen.

Solution To manually adjust the operation panel touchscreen, perform the following: 1.Press the Utility Key. 2.Press the number 5 on the keypad.This will bring up the touch panel adjustment. 3.Perform the adjustment and press the number 1 key. SPECIAL NOTE : Solution contribution by Mark D'Attilio, Production Print/SSD


DescriptionWhat are the contents of the 500K PM Kit?

Solution Please see the attached document whichlists all of the items contained in the PM kit. To viewthe PDF, Adobe Reader® must be installed. Adobe Reader®can be downloaded for free from the Adobe® web site at: http://www.adobe.com/products/acrobat/readstep2.html . SPECIAL NOTE : Solution contribution by Mark D'Attilio, Production Print/SSD


DescriptionDoes the main body NIC have the ability to E-mail meter counts?

Solution The main body NIC or the controller NIC does not have the capability to E-mail meter counts. SPECIAL NOTE : Solution contribution by Mark D'Attilio, Production Print/SSD

45




Description How to disable the charge and T/S corona cleaning function.

Solution To disable the charge and transfer/separation corona cleaning function, perform the following: 1.Enter Tech Rep mode. 2.Select System Input. 3.Select Software Switch Settings. 4.Go to switch 3-3 and 3-4 and select OFF. SPECIAL NOTE : Solution contribution by Mark D'Attilio, Production Print/SSD


Description Receiving code 77-81. Is the FS-516 compatible with the ZU-602?

Solution CAUSE: ZU602 dipswitch is set incorrectly. SOLUTION: FS516 is compatible but needs to have its firmware level to 30. ZU602 is compatible with the FS-516. Note: Installation guide states thathardware dipswitches 1&2 should be ON and 3&4 should be OFF on the ZUCB. Note: The latest version firmware or system software is available via the Konica Minolta Download Selector. Access the Selector from SSD Web Support (CSExpert Support) by clicking on 'Download MSDS, Drivers, Firmware and more'. SPECIAL NOTE: Solution contribution by Don St. Onge, Workgroup/SSD


DescriptionA PAPER DISCORD message is displayed on the operation panel when printing.What does this message mean?

Solution The PAPER DISCORD MESSAGE indicates a print job was sent to the printer and the paper size of the print job is not loaded in the machine papertrays.Either load the proper paper size in the paper tray or select the paper tray closest in size to the print job. SPECIAL NOTE : Solution contribution by Mark D'Attilio, Production Print/SSD


Description ZU-602, what paper sizes can be used and what types of folds can be performed?

Solution The ZU-602 will only perform Z-folds for 8.5x14 and 11x17 paper.No other type of folding is available. SPECIAL NOTE : Solution contribution by Mark D'Attilio, Production Print/SSD


DescriptionCan the auto reset timer setting for the operation panel can be set to manually reset the operation panel?Presently it takes 60 seconds for the reset to occur.

Solution If the reset function is turned off, pressing the reset button will reset the operation panel. To change the setting, enter Utility mode, then system setting. Selectitem 4 Panel reset timer setting. Change the setting to off. SPECIAL NOTE : Solution contribution by Greg Lantowski, Production Print/SSD

46




DescriptionHow to empty punch scraps

Solution 1. Open finisher door 2. Pull out the punch waste basket 3. Empty punch waste basket 4. Put punch waste basket back and close finisher door SPECIAL NOTE: Solution contribution by Raymond Downs, Production Customer Support/SSD


DescriptionICP (fuse)information for main body andfinishing options.

Solution Refer to the attached documents listing ICP information for: MAIN BODY Print control board Operation board/1 ADU driving board AC driving board Scanner driving board JAM indication board Toner control board LCT driving boards OPTIONS FS-604/FS-509/FS-516 PI-501 TU-501 ZU-601/ZU-602 Note : To viewa PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:http://www.adobe.com/products/acrobat/readstep2.html . SPECIAL NOTE : Solution contribution by Bob Moeller, Production Print/SSD


DescriptionHow to default the opening scan size of a scanned document from Adobe® Acrobat® 9.

Solution To default the opening scan size of a scanned document via Adobe® Acrobat® 9 perform the following: 1.Open a PDF. 2.Select Edit and then Preferences. 3.Click on Zoom to scroll and select the desired opening size. SPECIAL NOTE : Solution contribution by Mark D'Attilio and Ian Lynch, Production Print/SSD


Description

47



How to empty trimmer unit waste basket

Solution To empty the trimmer unit waste basket, perform the following: 1.Open trimmer unit frontdoor. 2.Pull out the waste basket. 3.Empty waste basket. 4.Put the waste basket back in original position and close trimmer front door securely. SPECIAL NOTE: Solution contribution by Raymond Downs, Production Customer Support/SSD


DescriptionIs it possible to print two lines on the tab?

Solution Two or three lines printed ona tab is not possible. Only one line printing is possible. This is a product specification. SPECIAL NOTE : Solution contribution by Mahen Shukla, ESS/BSE


DescriptionHow to enable punching of tabbed paper.

Solution To enable the punching of tabbed paper, perform the following: 1.Access Service mode. 2.Select [System Input]. 3.Select [Software Switch Setting]. 4.Use [+], [-] or numeric keys to access software switch 37-3. 5.Set software switch 37-3 to ON (1). Note :The machine must have minimum firmware level of 40 and the finisher aminimum level of 30. SPECIAL NOTE : Solution contribution by Bob Moeller, Production Print/SSD


DescriptionHow to open the Select Devices window when scanning with theTWAIN BW driver.

Solution The Select Devices window is accessed by performing the below steps when using the Konica Minolta version 2.1.0.0 BW TWAIN driver: 1. Select the Microsoft® Windows “Start” button. 2. Select “All Programs”. 3. Select “Konica Minolta”. 4. Select “TWAIN BW Driver”. 5. Select “Select Devices”. 6. When the Select Devices window opens, select the desired device. 7. Select OK. SPECIAL NOTE : Solution contribution by Ian Lynch, Production Print/SSD


DescriptionHow to load a 32-bit driver on a 64-bit operating system.

Solution Please follow this step-by-step procedure and refer to the attached video. 1. Load the 64-bit driver on the server and share it out.

48



2. Load a 32-bit driver on a workstation locally. 3. From the workstation perform the Run command to connect to the server (example: \\11.11.5.33) and press enter. This should bring up the server. 4.Navigate to the previously shared out printer on the server. 5. Right-click on the shared out printer and select properties. 6. Select the sharing tab and then click on the Additional Drivers button. 7. Select or check-off the 32-bit driver to be added to the 64-bit system. 8. Select OK and then browse to the folder that houses the 32-bit driver to be installed and select OK. The Additional Drivers window should now have the32-bitand 64-bit checked off. 9. Check the Additional Drivers of the Server to make sure that the 32-bit has been pushed up (right-click on the shared out printer of the server=>Properties =>Sharing Tab =>Additional Drivers). Notes : a.This was tested on like versions of 32-bit and 64-bit drivers. b.To viewthis procedure, Apple© QuickTime®should be installed.It can be downloaded for free at http://www.apple.com/quicktime/download/ . SPECIAL NOTE : Solution contribution by Freddie Burnham, Production Print/SSD


DescriptionHow to transfer the Management list to a USB drive.

Solution The bizhub PRO 920 cannot transfer the Management list to a USB drive. SPECIAL NOTE : Solution contribution by Gary Scimeca, Production Print/SSD


DescriptionHow many scanning destinations can be programmed?

Solution A total of 1000 destinations can be programmed to HDD, Email, SMB or FTP. SPECIAL NOTE : Solution contribution by Mark D'Attilio, Production Print/SSD


DescriptionWhat is the recommended MD5 checker?

Solution Therecommended MD5 checker is HkSFV (download attached file). HkSFV uses CRC-32 and MD5 technology to validate the integrity of files that you have downloaded or moved through a potentially unstable medium (burntto CD, transferred over the Internet/LAN). HkSFV can verify your files in seconds and is compatible with Win-SFV and md5sum. HkSFV is the simple, easy and most automatic application to create or check SFV and MD5 files. What is an SFV? An SFV file is a tiny list of files and CRCs, which allow you to check to see if the files you have downloaded are exactly what you are expecting. The CRCalgorithm used in SFV files allows you to see if the file you have has been changed, even a single byte, since the SFV file was created. What is an MD5? MD5 did not exist until somewhat recently, as md5sum is a popular UNIX format similar to SFV and UNIX does not use file extensions the way Microsoft®Windows-based systems do. MD5 uses the md5 algorithm to computechecksums, rather than the CRC-32method used by SFV. The md5 algorithm is almostas fast as CRC-32, but it is much more accurate at detecting changes in files. Some key features of HkSFV: Easy installation and automatic uninstallation (leaves no trace in the registry, even goes one step further than most programs and restores previous fileassociations when you remove it) One-click creation and checking of SFVs and MD5s Flawless & smooth upgrading to new versions (simply install the new version) Automatic association with SFV files, and an option to fix file association when other programs steal it Handles SFV and MD5 files from any other program invisibly (including files created on *NIX) Database/cache of previously checked files Batch SFV and MD5 checking - queue up and check many SFVs and MD5s in one pass, specify a directory and check all the SFVs and MD5s in thatdirectory (including subdirectories, if you want) Automatically find renamed files while checking SFV or MD5 files Enqueue SFVs or MD5s during file verification Recursive directory support during creation and verification

49



Supports creation of .bad and .missing files, or deleting failed files Drag-and-drop SFV or MD5 file or directory to create/check SFV or MD5 SPECIAL NOTE : Solution contribution by Gregg Gallant, Production Print/SSD


DescriptionConfiguration sheet, Specification sheet and Specification and Installation Guide.

Solution Please see attached documentation: 1. Configuration Sheet which shows option configurationwith: FS-516 FS-604 LU-403 LU-404 MK-707 PI-501 PK-505 TU-501 ZU-602 2. Specification Sheet which lists the General Specifications. 3. Specification and Installation Guide which addresses topics such as: Duty Cycle Space Requirements Environmental Requirements Electrical Requirements Paper Information Product Specifications How to Build a System for the bizhub 920 Printer/Copier/Scanner (from start to finish) Accessory Options for bizhub 920 Printer/Copier/Scanner Note : To view a PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:http://www.adobe.com/products/acrobat/readstep2.html .


DescriptionHow to determine the MAC address of the mainbody NIC or the controller NIC.

Solution The easiest method to determine theMAC address is to type the following line of text from a DOS prompt: arp <space> TCP/IP address of themainbodyNIC <space> - a <carriage return> The screen will display theTCP/IP address followed by the physical address (MAC address). SPECIAL NOTE : Solution contribution by Greg Lantowski, Production Print/SSD

50


bizhub PRO 920 Original jam, no-feed, multi-feed, folding, tearing, skewing, curling


Description Can only print or copy 1 page when selecting more then one 11x17 and "Please wait finisher is operating" message is indicated.

Solution CAUSE: Tray 3 paper feed motor has failed. SOLUTION: Replace Tray 3 paper feed motor (p/n 65AA80020). SPECIAL NOTE : Solution contribution by Mark D'Attilio, Production Print/SSD

51


bizhub PRO 920 Paper Conveyance jams, no-feed, folding, tearing, skewing, curling


DescriptionFS-xxx, first page not aligned properly/not stapled in stapled sets.

Solution CAUSE:Static build-up onalignment plate which causes the first page to stick. SOLUTION:Wipe affected are with anti-static compound (Brillianize®, Pledge®, dryer sheet, etc.). SPECIAL NOTE : Solution contribution by Chuck Tripp, Production Print/SSD


DescriptionFS-604/PK-505, J72-43 when punching.A few copies/prints may be punched before the jam occurs.

Solution PROBABLE CAUSES: 1. A cold solder joint on the PKCB is causing the problem or the PKCB has failed. Inspect the PKCB for any cold solder joints and repair as needed. Replace the PKCB if needed (p/n 15KA-9010). 2. After performing all PK-505 adjustments and replacing the PK driver board (p/n 15KA-9010), the problem still exists. The main body printer control boardhas failed. Replace the main body printer control board (p/n 57GA-9022F). SPECIAL NOTE : Solution contribution by Mark D'Attilio, Production Print/SSD and Harold Kammerer, KMBS Wichita


DescriptionFS-504/FS-509/FS-604, error codes C1137 (C-1137), J72-16 or J72-18 when stapling. Additionally, SC77-81 may be indicated.

Solution CAUSE: Damaged paper guide(s) - small nick(s)from paper entering the conveyance guide plate. SOLUTION:Look at the clear guide FN5: 1. Loosen the two rail screwsallowing the finisher to be pulled outan extra three inches. 2. Lower FN5 and feel the plastic ribs on the rear of the guide. 3. The lastrib on the guide (see attachment for a visual)haspaper cutsor burrs on it causing the paper to drag and jam whenstapling. Use a piece of very fine sandpaper or Scotchbrite® to smooth nick(s). Replace the conveyance guide plate(p/n 15JK45081) and/or (p/n15JK45190)ifnecessary. SPECIAL NOTE : Solution contribution by Greg Lantowski and Mike McCarthy, Production Print/SSD as well as Rod Willoughby, Perry Corporation


DescriptionStaple buckling only on corner staple with the FS-604.

Solution CAUSE: As single corner (oblique) stapling is performed on rear side, the stapler/R and clincher/R rotate 45 degrees around the respective rotation shafts(rotation bushings). Typically, due to manually moving the stapler unit by hand, the concentricity of these two rotation shafts may not be correctly aligned.Performing the Stapler Vertical Position Adjustment outlined in the Field Service Manual does not correct this issue. The two rotation shafts (bushings) mustbe concentric or this issue will occur.

52



SOLUTION: Perform the adjustment outlined in the attached document. SPECIAL NOTE : Solution provided by David Holt, District Service Manager.


DescriptionFS-604 jams (no code) with cover sheet 90lb index fed from the bypass tray in sort/staple mode in combination with 20lb paper only when copying.

Solution CAUSE: Older version firmware installed on the main body, IC-203 and FS-604. SOLUTION: Update the main body machine to minimum versions: Print control = 14, Image control = 40, IC-203 = 21, FS-604 = 30. SPECIAL NOTE : Solution contribution by Mark D'Attilio, Production Print/SSD


DescriptionJ10-01 when inserting a tab from the bypass tray.

Solution CAUSE: The bypass manual feed driving gear C (33T)has failed. SOLUTION: Replace themanual feed driven gear C (p/n 55VA 7718 1). SPECIAL NOTE : Solution contribution by Mark D'Attilio, Production Print/SSD


DescriptionJ17-08.

Solution CAUSE: Improper installation of the paper dust removing brush for the registration roller.

SOLUTION: When installing the paper dust removing brush for the registration roller, be sure to insert it fully until it hits against the back. When not insertedfully, the light path for detection of the registration sensor, PS40 (PS44 for bizhub PRO 920) will become blocked, thus resulting in a jam indication. Note : This code may occur when printing or copying. The J17-08 will still be displayed, but may not belisted on the jam list. SPECIAL NOTE : Solution contribution by Chuck Tripp, Production Print/SSD


Description ZU-601/ZU-602, J73-15 in idle.

Solution PROBABLE CAUSES: 1.Sensor detection error may occur if one of three reflective sheets attached to the guide plate become detached. Replace the entrance guide plate assembly (p/n 15KSR70200). SPECIAL NOTE : Solution contribution by Mark D'Attilio, Production Print/SSD 2. The entrance guide plate (p/n 15KS-5160) is contaminated. The guide plate has a chrome finish and is used as a reflector for the five edge detect sensors.If contaminated, the sensors cannot be properly adjusted. Note :Cannot adjust all or some oftheedge detect sensors on the ZU unit. Remove the punch unit from the ZK unit. Remove the guide (two screws) and clean the guide being careful to not dull the finish. After reassembly, performthe paper edge sensor sensitivity adjustment. SPECIAL NOTE : Solution contribution by Bob Moeller, Production Print/SSD

53




DescriptionFS-602/FS-604/FS-606, paper is wrinkledwhen folding 8.5x11.

Solution CAUSE: Paper is binding in the finisher. SOLUTION: Install modified paper guide stay assembly. Please refer to attached Bulletin Number5839. To viewthe PDF, Adobe Reader® must be installed.Adobe Reader® can be downloaded for free from the Adobe® web site at: http://www.adobe.com/products/acrobat/readstep2.html . SPECIAL NOTE : Solution contribution by Chuck Tripp, Production Print/SSD


DescriptionJ94-02 while duplexing. J17-03may also be indicated.

Solution CAUSE:Printer registration loop adjustment (2nd side) is required and/or the manual feed driving gear is worn/slipping causing loss of drive to the ADU exitsection. SOLUTION: Increase printer registration loop adjustment +3 value. Service Mode => Machine adj => Timing adj. => Printer reg loop adj. => Side 2LS290 & LS460. Clean/replace both Manual Feed Driving Gears (p/n 55VA 7718 1). Note : There are 2 manual feed driving gears in the drive assembly. Both should be replaced at the same time. Before disassembling, note the orientationof the gears as they are one-way gears. SPECIAL NOTE : Solution contribution by Mike McCarthy and Bob Moeller, Production Print/SSD


DescriptionFS-509/FS-604, J72-30 error code which may be intermittent.

Solution PROBABLE CAUSES: FS-509 1. FS-509 Paper Exit Belt assembly has been modified to prevent the jam code. Please see Parts Modification Notice for details. 2. PS6 wiring, pin or connector on the FS-509 is faulty. Note : The jamming usually occurs when running large jobs and J72-17or J17-29 may also be indicated. Inspect PS6 pins, connector and wiring on the actual sensor and repair as needed. FS-604 3. PS6 may be damaged even thoughinput check 76-5 shows PS6 working correctly. Note : The jam code may occur when using the FS-604 to staple and J72-20 may also be indicated. SOLUTION: Replace PS6 (p/n 08AA 8551 2). 4. Due to paper curl, the paper exit sensor, which is located at the center of paper width, cannot properly detect the paper. To correct: a.Load the paper upside down in the tray. b. If the problem persists, use theattached FS-604 special firmware that corrects the detection timing of the sensor.Please refer to Release Notes prior tofirmware installation. To view a PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:http://www.adobe.com/products/acrobat/readstep2.html . SPECIAL NOTE : Solution contribution by Mark D'Attilio/Mike McCarthy, Production Print/SSD and KMBT (Japan)


DescriptionJ72-43 when feeding paper from the LU-403/LU-404 and punching. The jam occurs at the PK-505/FS-604. Paper shifts as it comes out of the LU and shiftsagain as it nears the punch unit.

Solution

54



CAUSE: An anomaly in the program requires the LU-403/LU-404 tray size setting to be changed to a different size paper and then back to 8.5x11. SOLUTION: Perform the following procedure to set the LU-403/404 to standard 8.5x11 paper: 1. Enter the Tech Rep mode by pressing the Utility key and then Stop, 0, 0, Stop, 0, 1. 2. Select System Input. 3. Select Size Setting Tray 4. 4. Select Standard Size. 5. Select A4 and return to normal copy mode. Power cycle the machine. 6. Perform steps 1 thru 5, but this time select 8.5x11 as the LU-403/LU-404 paper size. 7. Power cycle the machine one more time and test the punch operation. SPECIAL NOTE : Solution contribution by Greg Lantowski, Production Print/SSD


DescriptionFS-604, J72-26 only when folding 3 sheets at a time.

Solution CAUSE: The folding rollers are dirty or contaminated. SOLUTION: Remove to the stacker unit to access the folding rollers. Clean the folding rollers using alcohol or a like substance. SPECIAL NOTE : Solution contribution by Mark D'Attilio, Production Print/SSD


Description Bent corner of copy or folded lead edge when duplexing.

Solution CAUSE: The registration roller dust removal brush has become oversaturated with debris. SOLUTION: Clean or replace brush (p/n 55VA 4608 0). SPECIAL NOTE : Solution contribution by Chuck Tripp, Production Print/SSD

Solution ID Solution UsageTAUS0808133JP*

DescriptionIntermittent J32-11 codes.

Solution CAUSE:The paper exit drive motor has failed. SOLUTION:Replace the paper exit drive motor M7 (p/n 56AA 8011 2). SPECIAL NOTE : Solution contribution by Mark D'Attilio, Production Print/SSD


DescriptionPaper trays will not unlock from the MFP.

Solution CAUSE: If any of the paper tray release handlesreads Off in the I/O mode,all paper trays will be locked. This prevents two trays being opened at the sametime. SOLUTION: To check the release lock handle sensors, perform the following: 1. Enter Service mode. 2. Select Machine Status. 3. Select I/O Check and enter 18 for the Code. Enter one of the following Multi codes and verify none read Off. If one of the handle release sensors reads Off,remove the cover from that paper tray and verify the operation of the handle release sensor. a. To check the handle release sensor (PS14) for Tray 1, enter 1 for the Multi code.

55



b. To check the handle release sensor (PS15) for Tray 2, enter2 for the Multi code. c. To check the handle release sensor (PS16) for Tray 3, enter3 for the Multi code. SPECIAL NOTE : Solution contribution by Gary Scimeca, Production Print/SSD


DescriptionJamming from all main body paper trays. The paper has not left the paper tray(s).

Solution CAUSE: The paper feed motor is not operating. SOLUTION: If the paper feed motor does not operate in normal mode or in I/O mode check the intermediate connector in the wiring harness near the paperfeed motor for a poor connection or bent pin. Repair as needed. SPECIAL NOTE : Solution contribution by Bob Moeller, Production Print/SSD


Description "Please wait finisher is operating" message and only 1 page is printed or copied when selecting more than one 11x17 copies/prints to be fed from Tray 3.

Solution CAUSE: Tray 3 paper feed motor has failed. SOLUTION: Replace Tray 3 feed motor (p/n 65AA 8002 0). SPECIAL NOTE : Solution contribution by Mark D'Attilio, Production Print/SSD


DescriptionPLEASE WAIT FINISHER OPERATING message when using the LCT.

Solution CAUSE: Photo sensor PS108 in the LCT is slightly angled or the actuator is binding causing misfeeds and the message. SOLUTION: Adjust\repair the position or replace PS108 (p\n 08AA 8551 2). SPECIAL NOTE : Solution contribution by Gregg Gallant, Production Print/SSD


DescriptionZU-602/ZU-607, Paper Edge sensor (PESB)sometimes does not detect paper.

Solution CAUSE: Sensor sensitivity of the PESB (p/n 13NK -961 1)is low. SOLUTION: First, clean the sensor. If the problem persists, the sensor light reflection label may become fogged with moisture from paper, deteriorating thelight receiving sensitivity. To correct it, perform the following: 1. Rotate the sensor volume (VR) on the paper edge sensor board (PESB) fully clockwise. 2. The corresponding LED will turn OFF. 3. Slowly rotate the VR counterclockwise. 4. When the LED turns ON, rotate the VR further by about 10 degrees and stop rotating. With the VR at this position, the sensitivity increases. Note :For standard adjustment, itinstructs to rotate the VR counterclockwise and stop rotating when the LED turns ON. CAUTION :If this action is taken, paper detection margin increases for thin paper. Tracing paper, thin paper may be seen through and not detected.If paperis not detected at all after the above action and adjustment, the sensor light reflection label may have detached. Please check it. SPECIAL NOTE : Solution contribution by KMBT (Japan)


DescriptionFS-604, corner staple mispositioned.

56



Solution CAUSE: The wiring harness for the front stapler does not have enough slack, preventing the rear stapler from fully reaching the correct corner position. SOLUTION: Reposition the front stapler harness to allow more slack which will allow the rear stapler to fully reach the corner position. SPECIAL NOTE : Solution contribution by Ron Lapham, Coastal Business System, Eureka, CA


DescriptionZU-602, J72-60 when punching

Solution CAUSE: The ZU-602 control board has failed. SOLUTION: After confirming all adjustments have been perform on the ZU unit and the problem remains, replace the ZU-602 control board (p/n15KS-9012F). SPECIAL NOTE : Solution contribution by Bob Moeller, Production Print/SSD


DescriptionFS-604, exited staple sets are wrinkled from the exit belt hook.

Solution CAUSE: The sponge paper assist roller mounted in the middle of the stacker is out of position and is interfering with the exited sets. J72-20 may also occur. SOLUTION: Inspect the sponge assist roller (p/n 20AK 4210 0) for free movement. Correct any binding and adjust the solenoid if necessary. The rollershould be in the up position when at rest and when the set is being exited. SPECIAL NOTE : Solution contribution by Bob Moeller, Production Print/SSD

57


bizhub PRO 920 Software/Driver related


DescriptionIntermittent No Reply from PING; no printing and cannot browse; requires reboot to recover.

Solution CAUSE:A vulnerability was corrected in early firmware where excessive SMB traffic can causethe NICto drop off. SOLUTION:Please use the following firmware version or higherto correct this issue. IC-611 (bizhub PRO 1050) Ver.30-COC0 IC-203 (bizhub PRO 920) Ver.20-COC0 IC-202 (bizhub 600/bizhub 750) Ver. 30-CH bizhub 360/420/500 Version 30 bizhub C450/C351/C250/C252/C352/C300 (Phase3.03/Ver.I8) Notes :1. If the issue is not resolved by the new firmware, please obtain details to further the investigations. Currently, here are the first items to confirm and provide. a. Provide answers to the following questions: What type of network environment is the customer using? What is the network speed? What is the NIC speed on our engine? When the device goes down can it be PINGed orbrowsed to? What protocols are on the network? Is the machine in a power save or sleep mode at the time of failure? Does the machine have a static TCP/IP address or is it dynamic (DHCP)? How often does the incident occur? Are there any routers, switches or hubs involved on the network segment(s)which aretrying to utilize the machine? What type of ‘special’ applications are utilized by people who print to the device? b. If a bizhub 600/750/PRO 920, you can perform a Hyperterminal session and set transfer to text to create text file that shows the controller activity. c. Perform an Ethereal network packet capture. Instructions are attached. 2. The latest version firmware and system software is available via the Konica Minolta Download Selector. Access the Selector from SSD Web Support (CSExpert Support) by clicking on 'Download MSDS, Drivers, Firmware and more'. 3. Refer to the attached PDF for reference. To view a PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe®web site at: http://www.adobe.com/products/acrobat/readstep2.html . SPECIAL NOTE : Solution contribution by Mahen Shukla, ESS/BSE


DescriptionThe entire print job is stapled instead of each set when printing multiple stapled sets from Microsoft® Word.

Solution CAUSE:The Collate option in the Microsoft® Word dialog box is selected. SOLUTION:When printing and stapling multiple sets, the Collate option in the Microsoft® Word dialog box must be deselected. SPECIAL NOTE : Solution contribution byEd Bellone and Mark D'Attilio, Production Print/SSD


Description HTTP 400 - Bad Request error. Unable to view the printer web browser (PageScope Web Connection).

58



Solution CAUSE: The reason for the error: 1. A bad request.The browser sent a request that the server could not understand. 2. An attempt to communicatewith plain HTTP to an SSL-enabled server port. Instead, use the HTTPS scheme to access the URL. 3.The request could not be understood by the server due to malformed syntax. The client SHOULD NOT repeat the request without modifications. Note : The first digit of the status code specifies one of five classes of response. 1xx Informational 2xx Success 3xx Redirection 4xx Client Error 5xx Server Error SOLUTION: The error can be eliminated by: 1. Checking for any enabled Pop-up blockers and reconfiguring them. 2. Checking for Internet security software that may be blocking Web access and disabling the service. Example: Norton© Internet Security. 3. Installing Microsoft® .NET Framework 1.1 Service Pack 1. Microsoft® has confirmed that this is a problem inMicrosoft® products that are listed in the"Applies to" section. This problem was first corrected in.NET Framework 1.1 Service Pack 1. Please refer to Microsoft® Article ID: 826437 - FIX: "HTTP 400 -Bad request" error message in the .NET Framework 1.1 . SPECIAL NOTE : Solution contribution by Cesar Jimenez, Production Print/SSD


Description Troubleshooting vCare/CS Remote Care E-mail communication failure.

Solution In the attached vCare/CS Remote Care E-mail Communication Troubleshooting Guide are troubleshooting methods and procedures to resolve vCare E-mailCommunication issues. Topics addressed are: A. Essential vCare Technician troubleshooting toolsB. Email Communication RequirementsC. Additional RequirementsD. Troubleshooting when a email communication test failsE. EMAIL Server ConsiderationsF. Determining the type of Authentication required on a Mail Server, through telnetG. Ethereal network capture to diagnose email connectivity issuesH. Performing a Communication Test, Printing the Communication Log and verifying that the MFP is communicating with the vCare systemI. Verifying through the vCare web application that MFP setup is completeJ. Example Mail Server logs which record a CSRC Communication Test and reception of a “setup email”K. Advanced Email Communication Troubleshooting Note : To viewthe PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:http://www.adobe.com/products/acrobat/readstep2.html . SPECIAL NOTE : Solution contribution by Ed Bellone, Production Print/SSD


DescriptionTCP socket error occurs when using PageScope Web Connection if latest Adobe® Flash Player (Version 9.0.124.0) is installed. This problem does not occuron Adobe® Flash Player(Version 9.0.115.0). "Socket connection error" message is displayed in the top center of the screen. Please see attached Websample.

Solution CAUSE: Firmware bug. SOLUTION: Konica Minolta Japan will be releasingfirmware to correct this issue. Please read the Release Notes to determine ifexisting firmwaremeets yourneeds. It will be noted if the firmwarecorrects the issue. Note : The latest version firmware or system software is available via the Konica Minolta Download Selector. Access the Selector from SSD Web Support(CS Expert Support) by clicking on 'Download MSDS, Drivers, Firmware and more'.

59



SPECIAL NOTE : Solution contribution by Paul Santangelo, ESS/BSE and Cesar Jimenez, Production Print/SSD


DescriptionUnable to print from Adobe® Acrobat® 8 with the Visual PostScript driver.

Solution CAUSE:An abnormality with the Visual PostScript driver. SOLUTION:Visual PostScript drivers areavailable that correct this issue. Microsoft® Windows NT4/2K/XP/2K3 (32-bit) bizhub Pro 1050 Visual PostScript driver version 3.2.0.0 bizhub Pro 920 Visual PostScript driver version 2.8.0.0 bizhub 750/600 Visual PostScript driver version 3.1.0.0 bizhub 500/420/360 Visual PostScript driver version 3.1.0.0 Microsoft® Windows XP Pro/2K3 (64-bit) bizhub Pro 1050 Visual PostScript driver version 3.2.0.0 bizhub Pro 920 Visual PostScript driver version 2.8.0.0 bizhub 750/600 Visual PostScript driver version 3.1.0.0 bizhub 500/420/360 Visual PostScript driver version 3.1.0.0 Note : The latest print drivers are available via the Konica Minolta Download Selector. Access the Selector from theKMBS public site (http://www.kmbs.konicaminolta.us ) Support & Drivers tab or from SSD Web Support (CS Expert Support) by clicking on 'Download MSDS, Drivers,Firmware and more'. SPECIAL NOTE : Solution contribution by Tony Pizzoferrato, ESS/SSD


DescriptionUnable to fold and center staple without selecting booklet mode when using the Visual PostScript driver for the bizhub PRO 920/IC-203 print system.

Solution CAUSE: An older version of the bizhub PRO 920/IC-203 Visual PostScript driver is installed.

SOLUTION: The 2.1.0.0 version or laterof the bizhub PRO 920/IC-203 Visual PostScript driveris available via the Konica Minolta Download Selector. Accessthe Selector from the KMBS public site ( http://www.kmbs.konicaminolta.us ) Support & Drivers tab or from SSD Web Support (CS Expert Support) byclicking on 'Download MSDS, Drivers, Firmware and more'. Before installing the driver please be sure to remove the previous version of the bizhub PRO 920/IC-203 driver from the workstation using the followingsteps:1. Open the printers and faxes dialog box.2. Select file.3. Select server properties.4. Select drivers.5. Select the bizhub PRO 920/IC-203 Visual PostScript driver and click Remove.At this point, the 2.1.0.0 version of the bizhub PRO 920/IC-203 Visual PostScript driver can be installed to realize the new functionality. Note : For additional information about how to manually remove printer drivers, refer to attached documentation. To viewthe PDF, Adobe Reader® must beinstalled. Adobe Reader® can be downloaded for free from the Adobe® web site at: http://www.adobe.com/products/acrobat/readstep2.html


DescriptionWhen scanning with eCopy™, the preview is not displayed, the optics did not work and the message at the bottom left of the scan indicates 'Scan complete'.

Solution CAUSE: There issomewhat of an incompatiblity with most ofthe KMBSTWAIN drivers and the eCopy™ ScanStation. SOLUTION:There is a driver that does work well and supports color scanning. This has been commonly referred to as the GUI-suppressed (Non GUI) driver. Notes : 1.Prior to installation, unload the presentTWAIN drivervia Control Panel=> Add or Remove Programs. IMPORTANT : Stop ALL eCopy™ services in order to remove the driver. 2. The latest TWAIN driveris available via the Konica Minolta Download Selector. Access the Selector from theKMBS public site (http://www.kmbs.konicaminolta.us ) Support & Drivers tab or from SSD Web Support (CS Expert Support) by clicking on 'Download MSDS, Drivers,Firmware and more'.

60



SPECIAL NOTE : Solution contribution by Paul Santangelo, ESS/BSE


DescriptionWhen loading ISWTrns on Microsoft® Vista™, USB is not available under Settings.

Solution CAUSE: Earlier ISWTrns version is being used. SOLUTION: The USB feature is available in ISWTrns utility version 3.74E and newer. SPECIAL NOTE : Solution contribution by Chuck Tripp, Production Print/SSD


DescriptionWhen printing from Microsoft® Publisher andperforming a mail merge, thecopiesare all stapled together.

Solution CAUSE: This is a known anomaly with Microsoft® applications. SOLUTION: Please read the attached Microsoft® articleregarding a resolution for the problem with Microsoft® Publisher 2000 and 2003. To viewthe PDF,Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:http://www.adobe.com/products/acrobat/readstep2.html . SPECIAL NOTE : Solution contribution by Mark D'Attilio, Production Print/SSD


DescriptionUnable to select booklet mode and a front cover sheet simultaneously when using the Visual PostScript driver for the bizhub PRO 920/IC-203 print system.

SolutionCAUSE: An older version of the bizhub PRO 920/IC-203 Visual PostScript driver is installed.

SOLUTION: The 2.1.0.0 version or laterof the bizhub PRO 920/IC-203 Visual PostScript driveris available via the Konica Minolta Download Selector. Accessthe Selector from the KMBS public site ( http://www.kmbs.konicaminolta.us ) Support & Drivers tab or from SSD Web Support (CS Expert Support) byclicking on 'Download MSDS, Drivers, Firmware and more'. Before installing the driver please be sure to remove the previous version of the bizhub PRO 920/IC-203 driver from the workstation using the following steps:1. Open the printers and faxes dialog box.2. Select file.3. Select server properties.4. Select drivers.5. Select the bizhub PRO 920/IC-203 Visual PostScript driver and click Remove.At this point, the 2.1.0.0 version of the bizhub PRO 920/IC-203 Visual PostScript driver can be installed to realize the new functionality. Note : For additional information about how to manually remove printer drivers, refer to attached documentation. To viewthe PDF, Adobe Reader® must beinstalled. Adobe Reader® can be downloaded for free from the Adobe® web site at: http://www.adobe.com/products/acrobat/readstep2.html


DescriptionA PDF cannot be output from Adobe® Acrobat® 8.

Solution CAUSE: Bugin theKonica MinoltaVisual PostScript driver. SOLUTION: Please use the special Konica MinoltaVisual PostScript driver (32-bit or 64-bit as needed), version 3.2.0.0 (bizhub PRO 1050/1050P/IC-611)orversion 2.8.0.0 (bizhub PRO 920/IC-203). Note : The latest print drivers are available via the Konica Minolta Download Selector. Access the Selector from the the KMBS public site (http://www.kmbs.konicaminolta.us ) Support & Drivers tab or from SSD Web Support (CS Expert Support) by clicking on 'Download MSDS, Drivers,Firmware and more'. SPECIAL NOTE : Solution contribution by KMBT (Japan).

61




DescriptionWhy when trying to print a duplexed document using a 2-page overlay, is onlythe first page of the overlayshowing up on the document.

SolutionA 2-page overlay cannot be created. Overlays are .EPS files. EPS stands for Encapsulated PostScript. PostScript was originally designed only for sending toa printer but PostScript's ability to scale and translate (move the origin of) what follows makes it possible to embed pieces of PostScript and place themwheredesired on the page. These pieces are usually EPS files. EPS is considered a graphic file format. Under the rules of EPS, only single page PostScriptfiles can be translated. So to summarize; whencreating the "Overlay" (.EPS) file, no matter how many pages inthe current file, only one page will convert over and the rest will be lost. SPECIAL NOTE : Solution contribution by Chuck Tripp, Production Print/SSD


DescriptionCS Remote Care is grayed out in Service mode when setting up vCare.

Solution CAUSE: CS Remote Care recognition has been disabled. SOLUTION: In Service mode enable CS Remote Care by changing Software Switch Setting 15-5 to ON (1). SPECIAL NOTE : Solution contribution by Don St. Onge and Ian Lynch, Production Print/SSD, Workgroup/SSD


Description When trying to print mixed originals, the MPF will stop and display a message to "please load correct paper size".

Solution CAUSE:This is caused by incorrect DIP switch settings and/or incorrect firmware or drivers. SOLUTION: Be sure that the latest firmware and drivers are loaded, and that the DIP switches are set correctly. Firmware: Ver. I:40-CPH0 Driver: PCL Ver.2.04s, PS(Plug-in) Ver.2.1.66, PS(V) Ver.2.9.1.0 DipSW21-0=0 (Mixed size paper staple and punch for printer --> Allowed) DipSW21-6=1 (Punch control with page direction --> Check only 1st page of job) DipSW44-7=1 (PS Mixed binding position correction --> Enable) Note:The firmware is available for download via the Konica Minolta Download Selector.1. Login in via www.mykonicaminolta.com 2. Select the "Service" tab located at the top of the page.3. Select the "SSD (DNA, Drivers, MSDS)" link located to the left.4. Select the "Continue on to the SSD Home Page" link located in the middle of the page.5. Select the "Download MSDS, Drivers, Firmware and more" link located to the left. SPECIAL NOTE: Solution contribution by Craig Blyther, ASG/SSD


Description How to obtain spool files from an AS/400 for analysis by the lab.

Solution Because of the complexityand types of issues betweenMFPs and the AS/400, the Lab may occasionally require that a spool file be provided so that the exactissue can be re-created by the lab. There aretwo methods to follow, depending upon the OS version on the AS/400. Follow these steps to obtain the spool file. 1. Obtain the version of the OS/400 that is installed the AS/400 by issuing the following command: GO LICPGM (The user will need appropriate rights in order to do this.)

62



2. When the Work with Licensed Programs menu is displayed, type option 10 to display installed licensed programs. 3. After the list is displayed (it may take awhile), press F11 to display the release version. This will appearunder the Installed Release column. 4. Use theattached instructions to obtain the spool file. If the OS version is V5R4M0 or higher, then use instructions called Backing up Spool files System i V5R4Mx.pdf If the OS version is lower then V5R4M0, then use instructions called: Instructions to copy spool files off AS400 V5 using FTP-final.pdf 5. After thefiles are obtained,attach them to the SSD ticket. SPECIAL NOTE: Solution contribution by Paul Santangelo, ESS/BSE


DescriptionWhen printing AS/400® forms, the print does not line up with the form.

Solution CAUSE:The AS/400® is rasterizing the forms based on an HP® LaserJet 5si (this is by design).The margins are not set correctly and produces the offset. SOLUTION:Create or obtain a new WSCST (Workstation Customization Object)with the following keyword in it. DATASTREAM=HPPCL5 Replace the line with the following: DATASTREAM=HPPCL5I Thiswill tell HPT to image the form instead of rasterize it. Recompile the WSCST, end the writer, vary the device description OFF/ON and start the writer. When the job is sent, the form should be inline with the text. SPECIAL NOTE : Solution contribution by Paul Santangelo, ESS/BSE


DescriptionShortcut for Center Staple and Fold is grayed out. This does not occur when a Hotfolder is used that specifies the Fold – Multi Center Fold setting. This issuehas been confirmed to occur with PageScope Direct Print version 1.1.24 installed on XP Pro, with the bizhub PRO 920 firmware at version 40.0.

Solution CAUSE: An updated .dll file needs to be installed. SOLUTION: Copy the updated kmdpui01.dll to resolve this issue following this procedure. The original kmdpui01.dll is located in the folder C:\ProgramFiles\KONICA MINOLTA\PageScope Direct Print 1.1. 1. Rename the original kmdpui01.dll to kmdpui01.dll.old. 2. Copy the upated kmdpui01.dll patch to this folder. 3. Reboot the machine. Refer to the attached PDF file for details. Note: To view a PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:http://www.adobe.com/products/acrobat/readstep2.html SPECIAL NOTE: Solution contribution by Mark Kemp, ASG/SSD


DescriptionUsing eCopy™, after pressing function key, the next screen does not display the preview scan.

Solution CAUSE: The wrong TWAIN driver is being used. SOLUTION: The latest TWAIN driveris available via the Konica Minolta Download Selector. Access the Selector from theKMBS public site (http://www.kmbs.konicaminolta.us ) Support & Drivers tab or from SSD Web Support (CS Expert Support) by clicking on 'Download MSDS, Drivers,Firmware and more'.

63



Remove the current driver before installing this driver.If an error occurs during removal, stop the eCopy™ services and press the Retry button. Once removed,restart the eCopy™ services and install the new driver. SPECIAL NOTE : Solution contribution by Paul Santangelo, ESS/BSE


Description "There Was An Error Accessing AppleTalk Services- Is Services for Macintosh Installed?" message when launching MicroSpool™.

Solution CAUSE: Incorrect settings. Note : This occurs when launching MicroSpool™ in MicroPress® 7.0or MicroPress® 7.5. SOLUTION: To correct: 1. Go into Control Panel. 2. Add/ Remove Programs. 3. Add/ Remove Windows Components. 4. Highlight Other Network File and Print Services. 5. Check "File Services for Macintosh". 6. Check "Print Services for Macintosh". 7. Click OK. SPECIAL NOTE : Solution contribution by Cesar Jimenez, Production Print/SSD


DescriptionWhen a PDF is output from Adobe® Acrobat® 8, it generates a PostScript error.

Solution CAUSE: Bugin theKonica MinoltaVisual PostScript driver when settings are as follows: - Visual PostScript driver: “Path through - Off” - Adobe® Acrobat® 8: ”Choose Paper Source by PDF page size” SOLUTION: Please use the special Konica MinoltaVisual PostScript driver (32-bit or 64-bit as needed), version 3.2.0.0 (bizhub PRO 1050/1050P/IC-611)orversion 2.8.0.0 (bizhub PRO 920/IC-203). Note : The latest print drivers are available via the Konica Minolta Download Selector. Access the Selector from theKMBS public site (http://www.kmbs.konicaminolta.us ) Support & Drivers tab or from SSD Web Support (CS Expert Support) by clicking on 'Download MSDS, Drivers,Firmware and more'. SPECIAL NOTE : Solution contribution by KMBT (Japan).


DescriptionWhen printing from Adobe® Acrobat® 8, and page 220 is output from the PDF, 14 pages or more cannot print.

Solution CAUSE: Bugin theKonica MinoltaVisual PostScript driver. SOLUTION: Please use the special Konica MinoltaVisual PostScript driver (32-bit or 64-bit as needed), version 3.2.0.0 (bizhub PRO 1050/1050P/IC-611)orversion 2.8.0.0 (bizhub PRO 920/IC-203). Note : The latest print drivers are available via the Konica Minolta Download Selector. Access the Selector from the the KMBS public site (http://www.kmbs.konicaminolta.us ) Support & Drivers tab or from SSD Web Support (CS Expert Support) by clicking on 'Download MSDS, Drivers,Firmware and more'. SPECIAL NOTE : Solution contribution by KMBT (Japan).


DescriptionWhen a mixed original PDF (example: page 1 = 8.5x11 and page 2 = 8.5x14) is output from Acrobat® Reader 7.0.8, page 2 cannot be output.

Solution

64



CAUSE: Bugin theKonica MinoltaVisual PostScript driver when settings are as follows: - Staple: Left Binding + Staple - Hole punch: 2 Holes - Fold: Z-Fold SOLUTION: Please use the special Konica MinoltaVisual PostScript driver (32-bit or 64-bit as needed), version 3.2.0.0 (bizhub PRO 1050/1050P/IC-611)orversion 2.8.0.0 (bizhub PRO 920/IC-203). Note : The latest print drivers are available via the Konica Minolta Download Selector. Access the Selector from the the KMBS public site (http://www.kmbs.konicaminolta.us ) Support & Drivers tab or from SSD Web Support (CS Expert Support) by clicking on 'Download MSDS, Drivers,Firmware and more'. SPECIAL NOTE : Solution contribution by KMBT (Japan).


Description "Please load size Special paper in tray 1" message and page 2 cannot printwhen a mixed original PDF (example: page 1 = 8.5x11 and page 2 = 8.5x14) isoutput from Adobe® Acrobat® 8.1.

Solution CAUSE: Bugin thebizhubPostScript (Plug-in) driver. SOLUTION: Please use the special PostScript driver, version 3.0.171 (bizhub PRO 1050/1050P/IC-611)or version 2.1.52 (bizhub PRO 920/IC-203).Whenoutputting, please confirm the following: 1. Acrobat® 8 (Adobe® Reader 8) isversion8.1 or later.2.[File]=> [Print] => "Choose Paper source by PDF page size" is selected.3.[File] => [Print] => [Advanced] => [PostScript Options] => [Font and Resource Policy] => "Send for Each Page" is selected. Notes : 1.The latest print drivers are available via the Konica Minolta Download Selector. Access the Selector from the the KMBS public site (http://www.kmbs.konicaminolta.us ) Support & Drivers tab or from SSD Web Support (CS Expert Support) by clicking on 'Download MSDS, Drivers,Firmware and more'.This driver is also attached for convenient download. CAUTION : The file is large in size 63.6MB so ensure that a high-speedconnection is used. 2. Please refer to the attached Release Notes. To view the document, Microsoft® Word® or Word® Viewer must be installed. Word® Viewer 2003 (11.7MB)can be obtained free from Microsoft® at the following URL;http://www.microsoft.com/downloads/details.aspx?DisplayLang=en&FamilyID=95e24c87-8732-48d5-8689-ab826e7b8fdf . SPECIAL NOTE : Solution contribution by KMBT (Japan).


Description In PageScope Direct Print version 1.1.18.9,when setting the Default Print, Hotfolder or Shortcut setting, "Scaling" is not available as an adjustable setting. Note : The scaling setting is comparable to the "Graphic Scaling by Percentage %" setting" which can be set in the bizhub PRO 920/1050 driver.

Solution This functionality is currently not supported by Direct Print. However if a business case can be presented, Japan will consider adding this functionality. SPECIAL NOTE : Solution contribution by Mark Kemp, ESS/SSD


DescriptionThe greater than (>) and less than (<)symbols print out as an equal sign (=).

Solution CAUSE: An anomaly in the PCL driver. SOLUTION: As a workaround deselect USE PRINTER FONTS in the driver on the FONTS tab. Note : The PostScript drivers function properly. SPECIAL NOTE : Solution contribution by Mark D'Attilio, Production Print/SSD


Description"Please load size Special paper in Tray 1" message when a mixed original (Page 1: 8.5x11R + Page 2: 8.5x14)PDF file is output from Adobe Acrobat 8.1.

Solution CAUSE: Bug ofbizhub PRO920 or bizhub PRO 1050PostScript (Plug-in) driver.

SOLUTION: Please use the attached special driver version 2.1.54 for bizhub PRO920 (59.6MB)or version 3.0.173 for bizhub PRO 1050 (63.4MB).The

65



driverscan also be downloaded from the Konica Minolta Download Selector. Access the Selector from the KMBS public site (http://www.kmbs.konicaminolta.us ) Support & Drivers tab or from SSD Web Support (CS Expert Support) by clicking on 'Download MSDS, Drivers,Firmware and more'. Note : Please refer to attached Release Notes prior to driver installation. To viewthe PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:http://www.adobe.com/products/acrobat/readstep2.htm . SPECIAL NOTE : Solution contribution by KMBT (Japan).


Description Using Printgroove POD QUEUE; unable to perform Color Split Cluster printing with the bizhub PRO 920 and the bizhub PRO C6500. The page order of the color pages with the B/W pages maybe out of order and some color pages will remain in the bizhub PRO 920 Post Inserter.

Solution CAUSE: The bizhub PRO 920 does not support Color Split Cluster printing with Printgroove POD QUEUE. SOLUTION:The bizhub PRO 1050 and 7085 are the only B/W products that support Color Split Cluster printingwith Printgroove POD QUEUE. Future release of Printgroove POD QUEUE will include a contraint to not allow the creation of Color Split Clusters with the bizhub PRO 920. SPECIAL NOTE : Solution contribution by Tony Pizzoferrato, ESS/SSD


Description"Device can not print in accordance w/guidelines pick another printer" message when trying to print postage from Stamps.Com.

Solution CAUSE: Driver incompatibility. SOLUTION: Stamps.com states that they will not work with Konica Minoltadrivers.The only thing they will do is print labels, and you have to purchase thelabels from Stamps.com. SPECIAL NOTE : Solution contribution by Chuck Tripp, Production Print/SSD


Description Whentrying toprint, for example, 3 booklets from Foxit© Reader, machine makes one booklet with 3x first page, 3x second page, etc.

Solution CAUSE: Application restriction. SOLUTION: Please install and use Adobe® Acrobat Reader. Adobe Reader® can be downloaded for free from the Adobe® web site at:http://www.adobe.com/products/acrobat/readstep2.html . SPECIAL NOTE : Solution contribution by KMPoland (BPL).


Description Slow printing issue when utilizing Macintosh® OS 10.4.x.

66



Solution CAUSE: Issue with the CUPS daemon configuration file on Macintosh® OS 10.4.x. being corrupt. SOLUTION: The old CUPS daemon configuration file must be deleted and a new one created. Please see the attached document for instruction on how toremove and re-create the daemon configuration file. SPECIAL NOTE : Solution contribution by Tim Blevins - KMBS/Cleveland


DescriptionThe TWAIN Twack utility is not finding the IC-203 to test.

Solution CAUSE:The IC-203 cannot be auto-detected. SOLUTION:Manually add the controller after confirming the TCP/IP address.The name can be whatever you want. SPECIAL NOTE : Solution contribution by Jim Behrends, Production Print/SSD


Description“This mode unavailable for punch mode, punch mode will be cancelled" message on theMFP display when printing.

Solution CAUSE: Printer driver bug. SOLUTION: This issue has been escalated to Konica Minolta Japan. Use PCL version 2.0 as a workaround. SPECIAL NOTE : Solution contribution by Freddie Burnham, Production Print/SSD


DescriptionUnable to locate Insert Pages in the driver on a Macintosh® Intel® O/S 10.5.

Solution CAUSE: The standard Macintosh® Intel® PostScript driver does not have the Insert Pages option. SOLUTION:Install the attached SOFHA driver which has the Page Insert option. Note : The latest print drivers are also available via the Konica Minolta Download Selector. Access the Selector from the the KMBS public site (http://www.kmbs.konicaminolta.us ) Support & Drivers tab or from SSD Web Support (CS Expert Support) by clicking on 'Download MSDS, Drivers,Firmware and more'. SPECIAL NOTE : Solution contribution by Mark D'Attilio, Production Print/SSD


DescriptionMicrosoft® Word does not return to the default printer when closed and reopened.

Solution CAUSE: Microsoft® Outlook is open and is using Microsoft® Word asthe default program for editing messages. SOLUTION: To change the default mail message editing program perform the following: 1. Go into Microsoft® Outlook and select Tools from the tool bar. 2. Scroll down to Options. 3. Click on the Mail Format Tab. 4.Make sure the Use Microsoft Office Word 2003 to edit e-mail messages checkbox is selected. Note : In versions before Microsoft® Outlook 2003, the text reads Use Microsoft Word to edit e-mail messages . In Microsoft® Outlook 2007, there is nolonger an Outlook editor. The default is Microsoft® Word and cannot be changed. 5. Close the dialog. SPECIAL NOTE : Solution contribution by Jim Behrends, Production Print/SSD

67




DescriptionA Z-fold image is rotated when printing mixed media from Microsoft® Windows Vista™ 32-bit workstation. This occurs when using PCL or PostScript printdrivers.

Solution CAUSE: Application incompatibility with print driver function. SOLUTION: Use Adobe® Reader version 9.1.0 when printing with mixed size media and using the Z-fold functionality. SPECIAL NOTE : Solution contribution by Ron Reed, ASG/SSD

68


bizhub PRO 920 Warm-up, wrong display, incorrect operation, lock-up


DescriptionISW DATA ERROR 41 when attempting to flash the firmware.

Solution CAUSE: A printer is attached to LPT1 preventing the ISW utility from sending the file to LPT1.

SOLUTION: Remove the printer (or other device) that is attached to LPT1. SPECIAL NOTE : Solution contribution by Jim Behrends, Production Print/SSD


DescriptionSC23-01, SC28-04, SC29-01or SC29-02 code. Code may be intermittent.

Solution PROBABLE CAUSES: 1. The T/S corona unithas failed. Replace the T/S corona unit, (57GA-2700). SC23-01 2. The DCPS/2 has failed. Replace the DCPS/2 (p/n 57GA 8452 0). 3. The toner bottle has been inserted incorrectly and is binding. Remove the toner bottle and properly reinsert it. SC28-04 4.Loss of 24V DC to ICP5 on the ADU DB.To check ICP5, perform the following: a. Locate ICP5, just to the left of CN528 on the ADU DB. b. Place the machine in the 47 mode. c. Set your meter for 200V DC. d. Place your black meter lead to frame GRD. e. Take your red meter lead and check one side of ICP5 for 24V DC, then check the other side. f. If either side is missing 24V DC replace the ADU DB (p/n 57GA-9072E). 5. DSPS1 has failed. Replace DCPS1 (p/n 56UA 8451 0). SC29-01 6. The Toner Control Sensor Board has failed. Note : Code occurs during Auto Max. density adjustment after replacing developer. Copies may be lightand Error 1 may also be indicated. Clean and/or replace the TCSB (p/n 55VA-9510). SPECIAL NOTE : Solution contribution by Tom Kelly, Workgroup/SSD and Mark D'Attilio, Production Print/SSD


DescriptionDuring stapling operation, a missed staple or staples jamming in the stapler cartridge may occur. Clearing the jammed staple and reloading cartridge will allowthe staple function to resume.

Solution CAUSE: When replacement staples are installed, if the lead sheet is pulled in a forced manner, the staples can wear at the side wall of the staple cartridgecausing a skewed feed of the staples. This, along with normal wear of the staple cartridge, will causemisfeed of the staple during operation. SOLUTION: If the missed staple or staple jamming begins to occur more frequently for the customer, it is recommended to replace the staple cartridge (p/n15AA43560). SPECIAL NOTE : Solution contribution by Ron Reed, ESS/SSD

69




DescriptionAfter installing the PK-502, PK-503, PK-504 or PK-505 error codeC-1139 (C1139), J72-17 orJ72-18 is indicated.

SolutionCAUSE: When installingthe punch kitto the finisher (FS-504/FS-602, FS-509/FS-604),the mylarsheet at the entrance of the punch kit overlaps on the shutterplate of the finisher.

SOLUTION: After installing the punch kit, open/close the finisher entrance and conveyance guide/ once. When this operation is performed,the mylarpositioniscorrected. Please refer to theattached illustration.


DescriptionDF-606, RADF not recognized.

SolutionCAUSE: The RADF has been isolated with software switch settings.

SOLUTION: Access the software switch setting using the following procedure:1. Access the service (tech rep) mode - Press Utility/Counter, stop, 0, 0, stop, 0, 1.2. Touch System Input.3. Touch Software Switch Setting4. Use the + - selections to scroll to 18-45. Use Set Bit Data and set to OFF6. Power the machine OFF/ON to insure that the data is accepted.


DescriptionNot poweringON after a power outage. Wall voltage is good.

Solution CAUSE: Failed DCPS1. SOLUTION: Check for 220-240V AC at CN2-1 and CN2-3 of DCPS1 (this is the IN voltage). Disconnect CN74 and CN77 on DCPS1. This is to make surethat finisher is not holding down machine power. Replace DCPS1 if necessary (p/n 56UA84510). SPECIAL NOTE : Solution contribution by Mike McCarthy and Greg Lantowski, Production Print/SSD


DescriptionSC46-25.

Solution CAUSE: There are a variety of possible causes: The light blocking cover at the read section and the lens cover are removed. The connector of the CCD board is disconnected. The power cable of the CCD board is unplugged. The ICP of the CCD board is cut off. The light volume of the exposure lamp is excessive. The exposure lamp does not light up. SOLUTION: A list of things to check/replace: Check the light blocking and lens covers. Check for pinched or unplugged wires. Reseat the Image Control board (p/n 57GA-9010). Check for pinched wires or unplugged wires; reseat Image Control Board. Check CCD Board. Replace CCD Board (p/n 57GA-6302E). Check Exposure Lamp. Replace Exposure Lamp [L1] (p/n 56UA83010).

70



SPECIAL NOTE : Solution contribution by Jim Behrends, Production Print/SSD


DescriptionFS-516/FS-604, not recognized.

Solution CAUSE: The wiring for the PK (punch kit) is pinched or the PK board has failed. SOLUTION: To isolate the PK, remove CN61 and CN62 from the finisher control board and powerON the machine. If the finisher is recognized and functions,the PK is the cause. Inspect all PK related wiring for any pinched wires andcheck that all connectors are in their correct locations on the PK driverboard. Ifnecessary, replace the PK driver board (p/n 15KA-9010). SPECIAL NOTE : Solution contribution by Bob Moeller, Production Print/SSD


Description"Insert plug-in key counter" message after key counter is installed and enabled in billing management.

Solution CAUSE: The wrong connector has been used to connect counter to main body. SOLUTION: HECON® device may arrive withtwo connector types. Switch connectors. If this does not resolve issue, contact HECON® for assitance inobtaining correct connector for specific device. HECON® Copy Control Products are now handled exclusively bythe worldwidedistributor, High Tech Accessory Items, and bythe Canadian distributor,Densigraphix Kopi. Information on HECON® Copy Control Products can be found on their web sites below. Worldwide High Tech Accessory ItemsP.O. Box 7654Rocky Mount, NC 27804Phone: 800-541-9079Phone: 252-937-4991 Fax: 252-937-3847Sales: [email protected] Support: [email protected] Web Site: www.hightech-ai.com In Canada Densigraphix Kopi Inc.370 Britannia Road East, Suite 6Mississauga, Ontario L4Z 1X9 Phone: 888-364-6273Fax: 800-563-3192Sales: [email protected] Support: [email protected] Web Site: www.densi.com SPECIAL NOTE : Solution contribution by Chuck Tripp, Production Print/SSD


DescriptionSC36-06 every few days.The machine has more than a million copies on the meter.

Solution CAUSE: Fuser parts require replacement. SOLUTION:Replace the following parts:26AA53150 (x2) -heat sleeve26AA53160 (x2) -bearing56GAR7100 -cleaning sheet55VA53070 -auxiliary roller SPECIAL NOTE : Solution contribution by Jim Frost, Image Business Solutions

71




Description "Please Wait... Warming Up" message on the operation panel. If printing, the print operation may be interrupted. The message may also be constant with the MFP never reaching "Ready" status. The message may also be indicated every 5 minutes during MFP operation.

Solution PROBABLE CAUSES: 1.While tray is switched during copying or between jobs, if the process control changes (fusing temperature/line speed), the fusing pre-rotation is performed.To avoid interruption by the fusing pre-rotation, perform the following before continuous printing:Access [Utility] => [06 Administrator Setting] => [05 Copier/PrinterSetting] Set [Continuous Print (Print)] ON. Set [Continuous Print (Copy)] ON. Set [Fixing Prerotation Set] OFF. Concerns : a. If [Continuous Print (Print, Copy)] are turned ON, next job is exited directly and stacked on the paper exit tray.As there is no interval, it would be difficult toremove the previous job from the tray. b. If [Fusing prerotation Set] is turned OFF, the control is not performed when fusing temperature or line speed changes.Accordingly: When changing from fusing temperature HIGH to LOW, paper curl may be increased. When changing from fusing temperature LOW to HIGH, insufficient fusing may be occur. Note : Even ifthe aboveis performed, continuous printing will be interrupted by finisher operation when paper size changes or finishing mode changes. 2. bizhub PRO 920 - One of the heat lamps in the lower fuser roller has failed (either L2 or L3). Use a meter and check both heat lamps for continuity. Replace L2 (p/n 55VB 8302 2)or L3 (p/n 55VB 8303 3) as necessary. 3. bizhub PRO 920 - Fuser lamps do NOT come on due to a possible mechanical or sensor malfunction of the ADU section.Check the operation of the green handle lever #4 of the ADU release for proper operation. Check for bent or broken parts. Make sure that the sensor (p/n56AA 8551 0) is being flagged. Note : For lever and sensor reference see attached pagefrom the Parts Manual. To view the PDF, Adobe Reader® must be installed. Adobe Reader® canbe downloaded for free from the Adobe® web site at: http://www.adobe.com/products/acrobat/readstep2.html . 4. bizhub PRO 1050 series - A failed ADUDB1. Replace the failed ADU Drive Board Assembly (p/n 56UA 9072 G). 5. bizhub PRO 1050 series - Failed SW10 (front door switch). Note : If the installed PF-701 is removed from machine main body, machine status reaches "Ready" status. Install new SW10 interlock switch (p/n 12QR 8601 1). Note : Front door switch indicates that front door is closed, but the 24V DC line was interrupted. 6. bizhub PRO 1050 series -Software dipswitch 11-0 is set to ON which will prevent service codes from being displayed thus, masking the cause of amalfunction.Set software dipswitch 11-0 to OFF. This will allow service codes to be displayed and the cause of the problem can be identified. Note : This software switch should always be set to OFF to prevent potential equipment damage from an undetected service code. 7. bizhub PRO 1050 series -The AC Driver board failed. To isolate the problem, perform the following: a.Ensure both fixing lamps are not open by performing a continuity check. b.With a meter, check for 120V AC at the front terminal of the fixing unit where the lamp leads connect. c.If no voltage is present, the problem may be an open thermostat in the fixing unit. d.If voltage is present and the lamps check good, the problem is likely afailed AC driver board (p/n 56GB-9080). Note : At power up, one or both lamps may briefly flashON, then remain OFF. SPECIAL NOTE : Solution contribution by Freddie Burnham/Bob Moeller/Ian Lynch/Ed Bellone, Production Print/SSD and KM Europe (BEU)

72




Description SC46-17 at process start.

Solution CAUSE: Zoom is selected with a value of (0.000) in the Copier Initial settings mode. Note : The parameter memory board (NVRAM) was just replaced. SOLUTION: Access the Copier Initial mode, and change the value to an appropriate setting (i.e., 1.00, .50, .25) by performing the following procedure: 1. Press the Utility key. 2. Press Copy Setting. 3. Press Reset Setting. 4. Press Initial Setting. 5. Press the Zoom icon on the touchscreen. 6. Under Manual Adjustment, select the top left icon and enter 1000. 7. Press OK. SPECIAL NOTE : Solution contribution by Mark D'Attilio, Production Print/SSD


DescriptionFS-604, J73-01 at power up.

Solution CAUSE: Failed wiring harness. SOLUTION: Verify operation of the finisher exit sensor in diagnostics. Replace the wiring harness as needed (p/n 13QE90020). SPECIAL NOTE : Solution contribution by Mark D'Attilio, Production Print/SSD


Description FS-604, SC77-25 after the folding blade motor (M19) starts the home positon detection operation.

Solution CAUSE:The folding blade home sensor/LW (PS22) does not turn ON within a specified period of time. SOLUTION: Check CN6-1 for 24V DC on FSCB of the FS-604. Replace the FSCB (p/n 15SJ 901 0) if 24V DC is not present. Replace theFolding blade motor(M19) as needed (p/n 120H 8001 0). SPECIAL NOTE : Solution contribution by Mike McCarthy, Production Print/SSD


DescriptionUnable to access the main body NIC remote panel operation.

Solution CAUSE:The TCP/IP address of the PC has not been added to the NIC to allow this feature. SOLUTION:Add the PC TCP/IP address to the Main BodyNIC by performing the following: 1.Browse to the main body NIC, selectMachine Manager and enter the user name and password.User name is lowercase admin and the password is00000000 . 2.Select Remote Panel Setting/Job History. 3.Input the TCP/IP address of the PC into the remote panel registration box.Press registration and back to main menu. SPECIAL NOTE : Solution contribution by Mark D'Attilio and Mike McCarthy, Production Print/SSD

73




Description Slow printing (output) when printing many single jobs (e.g., mail merge).

Solution CAUSE: Those many single jobs are sent to the machine [Spool] and handed over to [Reserve Job] (= seen in the machine display). Handing over from[Spool] to [Reserve Job] happens only if a previous job is finished in [Reserve Job]. SOLUTION: Check setting of DIPSW 16-1 (Copy reservation function). If DIPSW is set to "1 [Disabled]" = slow printing/output If DIPSW is set to "0 [Enabled]" = fast printing/output SPECIAL NOTE : Solution contribution by KM Europe (BEU).


DescriptionWhen using custom paper sizes with regular sizes, the printer will cycle down before and after the custom paper is printed.

Solution CAUSE: Firmware update required. SOLUTION: Firmware has been released to correct for this issue. The firmware has been designed to fit a certain condition below: LCT = 8.5x11 Tray 1 = 8.5x11 Tray 3 =Custom Size(x=229/y=216); short edge is the lead edge. The firmware is Special Image Control Firmware version 40-UNT0 (Base Version: 40-UNS0) andit is attached below. This firmware is released for the following: Continuous output of different size pages in a job has been enabled (pages are output without pausing). Sizes: 8.5x11, 8.5x14, custom (229mm x 216mmonly) Continuous output of portrait job and landscape job with single stapling on the same side has been enabled (jobs are output without pausing). Stapling on thick cover pages (front and back) has been enabled. Dipswitch 39-4=0: Prohibited (current) or 39-4=1: Allowed When printing a job (per page setting) including tab paper, a message indicating "Duplex print unavailable" sometimes appeared. It has been corrected. SPECIAL NOTE : Solution contribution by Paul Santangelo, ESS/SSD


Description DF-606continually runs when feeding originals and the machine must be poweredOFF/ON tostop the problem.

Solution CAUSE: The wiring harness for theDF-606 original skew sensor (PS311) has failed. SOLUTION: Inspect and repair the wiring harness for PS311. If needed, replace the wiring harness (p/n 13GA90100). SPECIAL NOTE : Solution contribution by Mark D'Attilio, Production Print/SSD


DescriptionFS-604, intermittent J72-16 codes.

Solution CAUSE: Early version firmware is installed on the finisher. SOLUTION: Download and install version 30 firmware for the FS-509/FS-604/FS-516. The latest version firmware or system software is available via theKonica Minolta Download Selector. Access the Selector from SSD Web Support (CS Expert Support) by clicking on 'Download MSDS, Drivers, Firmware andmore'. SPECIAL NOTE : Solution contribution by Mark D'Attilio, Production Print/SSD


Description

74



The needless tab ejection option is grayed out after upgrading the main body firmware.

Solution CAUSE: The finisher firmware needs to upgraded. SOLUTION: Upgrade the finisher firmware to version 30 or above. The latest version firmware or system software is available via the Konica MinoltaDownload Selector. Access the Selector from SSD Web Support (CS Expert Support) by clicking on 'Download MSDS, Drivers, Firmware and more'. SPECIAL NOTE : Solution contribution by Mark D'Attilio, Production Print/SSD


DescriptionFS-509/FS-604, J72-22 andJ72-23.

Solution CAUSE:Sub-tray exit sensor (PS1) wiring has become disconnected from sensor. SOLUTION: Reconnect three yellow wires in this order. As sensor sits in machine: Pin 1 (top) = 5V DC, Pin 2 (middle) = signal - 5V DC and Pin 3 (bottom) =gnd - 0V DC. SPECIAL NOTE : Solution contribution by Mike McCarthy, Production Print/SSD


DescriptionPK-505 does not punch after replacing PKCB. Copy is positioned, ready to punch but punch never happens. No error code is displayed, however a J-7243shows in jam history. All 5 LEDs on PKCB are lit.

Solution CAUSE: The 5 LEDs are lit but not adjusted correctly on PKCB. SOLUTION: Turn each of the 5 LED adjusting "pots", on the PKCB, clockwise until each LED turns OFF. Then turn each adjustment screw CCW until eachLED lights.After all 5 LEDs are lit, perform a punch operation. SPECIAL NOTE : Solution contribution by Mike McCarthy, Production Print/SSD


DescriptionFS-604, intermittent J72-26 and J73-10 error codes.

Solution CAUSE: The spring that secures folding exit sensor(PS25) is not in the correct position. SOLUTION: Reposition the spring to eliminate the jamming problem. If damaged, replace the spring (p/n 3QE48080). SPECIAL NOTE : Solution contribution by Greg Lantowski, Production Print/SSD


DescriptionIntermittent J72-30 error with the FS-604 connected.

Solution CAUSE: The stacker entrance plates may be malformed. SOLUTION: Replace the 2 stacker entrance guide plates (p/n 13QE 4272 2E and p/n 13QE 4273 2). SPECIAL NOTE : Solution contribution by Gary Scimeca, Production Print/SSD


DescriptionBlank display on control panel and the MFP will not flash.

Solution CAUSE:Open F1 fuse in DCPS1.

75



SOLUTION:Replaceopen fuse and/orDCPS1 (p/n 57GB 8452 0). SPECIAL NOTE : Solution contribution byGreg Heinrich - Global Imaging Systems, Inc.


DescriptionSC90-01 at power ON.

Solution CAUSE: A 5-volt failure on the ADU driver board. SOLUTION: Check for 5V DC on each side of ICP3 and ICP4.If either isOPEN, inspect wiring for shorts. Replace ADU driver board (p/n 57GA-9072E). SPECIAL NOTE : Solution contribution by Jim Behrends, Production Print/SSD


DescriptionIntermittent "Uploading data" message on the operation panel when scanning to E-mail.

Solution CAUSE: Corrupt NIC or Hard Drive. SOLUTION: Perform a network setting clear and format the hard drive by performing the following: 1. Enter Admin mode. 2. Select IP NIC. 3. Press Next. 4. Press Network Setting Clear. To format the Hard drive perform the following: 1. Enter Tech Rep mode. 2. Select IP Hard Disk Format. 3. Select IP HDD Format and press Initialize. SPECIAL NOTE : Solution contribution by Mark D'Attilio, Production Print/SSD


Description SC42-20.

Solution CAUSE: The DCPS2 cooling fan (FM18)has failed. SOLUTION: Replace the cooling fan (p/n 56AA 8054 1). Note : The bizhub PRO 920 Service documentation on SC42-20 points to a failed cooling fan on DCPS1. Replacing the fans (FM19or FM20) on the DCPSwill not resolve this problem. SPECIAL NOTE : Solution contribution by Nicholas Ferrendelli, Western Region DSM


DescriptionCannot set up scan to SMB, FTP, HDD, or E-mail because the iconsare grayed out

Solution CAUSE: The features areset to "Restrict" in the Admin mode. SOLUTION: To enable these features, perform the following: 1. Press the Utility button. 2. Select Administrator. 3. Select System Setting. 4. Select Prohibit User Operations and set the requested scan feature to "Allow". SPECIAL NOTE : Solution contribution by Gary Scimeca, Production Print/SSD

76




DescriptionFS-604, SC77-14 when trying to saddle stitch or double staple.

Solution CAUSE:Staples are jammed in the stapler unit. SOLUTION:Remove both staple units and fully inspect the staple entrance area for jammed staples and remove as needed. SPECIAL NOTE : Solution contribution by Mark D'Attilio, Production Print/SSD


DescriptionFS-516, SC77-03 at power up.

Solution CAUSE: The FS-516 relay drive board has failed. SOLUTION: Replace the relay DB (p/n 15SF-9321E). SPECIAL NOTE : Solution contribution by Mark D'Attilio, Production Print/SSD


DescriptionFS-604/ZU-602, SC70-01.

Solution PROBABLE CAUSES: 1.Incorrect dipswitch setting on the ZU-602 control board. To set the dipswitch configuration perform the following: a. Access the ZU control board by removing the ZU rear cover. b. Locate the bank of dipswitches on the ZU control board (in the center of the board, directly below the silver heat sink). c. Turn ON dipswitch 1 and 2 (bottom 2 dipswitches). Ensure dipswitches 3 and 4 are set to OFF. 2. Corrupt firmware. Flash FS-604 to latest firmware. The latest version firmware or system software is available via the Konica Minolta Download Selector. Access the Selectorfrom SSD Web Support (CS Expert Support) by clicking on 'Download MSDS, Drivers, Firmware and more'. 3. Failed FSCB. Replace FS-604 FSCB (p/n 15SJ-9010). SPECIAL NOTE : Solution contribution by Bob Moeller and Mike McCarthy, Production Print/SSD


Description"Please load paper size" message from the platen or ADF. Able to manually select the tray. APS is enabled for both.

Solution CAUSE: Paper type is not set under the Auto Paper Type selection. SOLUTION: To set the Auto Paper Type Selection perform the following: 1. Select Utility. 2. Select Function Setting (B/W MFPs). a. SelectUser Setting for the color MFPs. b. System Setting for the color MFPs. 3. Select Feed Tray Setting. 4. Select Auto Paper Type Selection. 5. Set the paper type and color of the trays to use -usually Normal and White. 6. Return to normal operations screen and test. SPECIAL NOTE : Solution contribution by Jim Behrends, Production Print/SSD

77




DescriptionWhen the single corner (oblique) stapling is performed, the staple may buckle or not form correctly due to misalignment of the stapling unit to the clincher unit.

Solution CAUSE: Incorrect alignment of the stapling unit and clincher unit. SOLUTION: A procedure has been developed to allow the stapling unit and clincher unit to align correctly when the two units rotate to the corner stapleposition. Please see the attached document for the complete procedure. To view the document, Microsoft® Word® or Word® Viewer must be installed.Word® Viewer 2003 (11.7MB) can be obtained free from Microsoft® at the following URL;http://www.microsoft.com/downloads/details.aspx?DisplayLang=en&FamilyID=95e24c87-8732-48d5-8689-ab826e7b8fdf . SPECIAL NOTE : Procedure submitted by David Holt - DSM, Digital Systems


DescriptionC-4850 intermittently when printing 1000 pages or more.

Solution CAUSE: The Overall Control Board has failed. SOLUTION: Replace the OACB, (p/n 57GA-9010). Note : The OACB isindicated as the Image CB in the Parts Manual. SPECIAL NOTE : Solution contribution by Mark D'Attilio, Production Print/SSD


DescriptionIntermittent SC46-06 codes when printing.

Solution CAUSE: The OACB has failed. SOLUTION: Replace the failed OACB, (p/n 57GA-9010). SPECIAL NOTE : Solution contribution by Mark D'Attilio, Production Print/SSD


Description FS-604, when tri-fold is selected the sheet is ejected with only one fold.

Solution CAUSE: The tri-folding gate operated by SD6 in the stacker is binding or is damaged allowing the sheet to pass without performing the second fold. SOLUTION: To inspect, withdraw the finisher stacker. On the lower left side of the stacker is a black plastic guide. Inside the guide is the tri-folding gatewhich is operated by the tri-folding gate solenoid located to the rear of the gate. Inspect the solenoid, linkages for any damage or binding and repair asneeded. SPECIAL NOTE : Solution contribution by Bob Moeller, Production Print/SSD


DescriptionSC46-06 intermittentlyor randomly.

Solution CAUSE: The Overall Control Board has failed. SOLUTION: Replace the OACB (p/n 57GA-9010). SPECIAL NOTE : Solution contribution by Mark D'Attilio, Production Print/SSD


DescriptionWhen printing multi-page 11x17 job from MicroPress® 7.x to the bizhub PRO 920 the job will print half way and then an error page will be printed stating

78



"Invalid Page Eject Count Error". PrintStation Manager™ willindicate that the job was printed, but only half the document is printed.

Solution CAUSE: The bizhub PRO 920 is set to count 11x17 as two clicks. This setting will report back to MicroPress® that two pages were printed instead of one. SOLUTION: Set dipswitch 4-7 to 0 for the bizhub PRO 920.An 11x17 page will count as one click. This issue has been fixed with MicroPress® 7.5.0.1 usingthe following firmware levels: IP Control: 70-COB1 Image Control: 40-0000 Print Control: 14-0000 SPECIAL NOTE : Solution contribution by Bob Felch, ESS/SSD


Description "PLEASE LOAD 8.5x14 PAPER" message with an 8.5x14 original place on the platen glass and 8.5x14 paper is loaded in all trays of the machine.

Solution CAUSE: Paper type is not set correctly under the Auto Paper Type selection. SOLUTION: To set the Auto Paper Type Selection perform the following: 1. Select Utility. 2. Select Function Setting. 3. Select Feed Tray Setting. 4. Select Auto Paper Type Selection. 5. Set the paper type and color of the trays to use. Usually Normal and White. Whitemust be selected or it will not work. 6. Return to normal operations screen and test. SPECIAL NOTE : Solution contribution by Greg Lantowski, Production Print/SSD


Description The interrupt key is not stopping print jobs immediately.

Solution CAUSE: Incorrect setting in Admin mode. SOLUTION: To program theinterruptoption to stop jobs immediately, perform the following procedure. 1. Enter Admin mode. 2. Select Copier/Printer. 3. Select Suspend Interruption. 4. Select Stop Immediately and press OK. SPECIAL NOTE : Solution contribution by Mark D'Attilio, Production Print/SSD


DescriptionSC77-56.

Solution CAUSE: The punch scrap removal mechanism is bound up due to a build up of punch scraps in the auger or scrap tube. SOLUTION: Access the scrap removal auger and inspect for a build up of scraps. Thoroughly inspect the area where the scrap tube and auger meet. SPECIAL NOTE : Solution contribution by Bob Moeller, Production Print/SSD


Description SC52-09code after replacing HDD.

Solution CAUSE:Cooling Fan/3 which was disconnected to replace HDD was not reconnected. SOLUTION: Reconnect Cooling Fan/3. SPECIAL NOTE : Solution contribution by David Aekus, Production Print/SSD

79




DescriptionJ13-02 when duplexing.

Solution CAUSE: Vertical conveyance clutch failed. SOLUTION:Replace vertical conveyance clutch CL9 and CL10 (p/n 57GA82010). SPECIAL NOTE : Solution contribution by Mike McCarthy, Production Print/SSD


DescriptionThe Equitrac© system is not counting copies and prints.

Solution PROBABLE CAUSES: 1. Incorrect driver settings. In the driver settings, change Output setting from Optimize for Speed to Optimize for Portability. Note : If the Microsoft® Windows 2000/2003 printer driver is being used, change setting under 'Printing Defaults' on the server. 2. Failed ACDB. If no 24V DC pulse is seen with a test meter at the connector for the Equitrac© system, check/replace the ACDB (p/n 56GA-9082R). SPECIAL NOTE : Solution contribution by Greg Lantowski, Production Print/SSD


DescriptionSC67-03 only when the DF-606 is lowered when powering on the machine.If the document feeder is left in the raised position and the machine is poweredON,the machine works properly.

Solution CAUSE: Possible "dirty" RADF photosensors. SOLUTION: Inspect and clean all of the RADF photosensors. They may be causing this problem as evidenced from actual field experience. SPECIAL NOTE : Solution contribution by Greg Lantowski, Production Print/SSD


DescriptionJ73-09 when making booklets using sheet insertion.

Solution CAUSE: The printer control firmware needs to be updated. SOLUTION: Upgrade the printer control firmware to version 14 or aboveThe latest version firmware or system software is available via the Konica MinoltaDownload Selector. Access the Selector from SSD Web Support (CS Expert Support) by clicking on 'Download MSDS, Drivers, Firmware and more'. SPECIAL NOTE : Solution contribution by Gary Scimeca, Production Print/SSD


DescriptionFS-604, SC77-04 after the paper exits the finisher.

Solution CAUSE: The punch unit wiring harness is preventing the punch unit from shifting. SOLUTION: Re-route the punch unit wiring harness so that it does not interfere with the shifting of the punch unit. SPECIAL NOTE : Solution contribution by Mark D'Attilio, Production Print/SSD

80




DescriptionWhen scanning to E-mail a message of, DATA SIZE IS TO LARGE is displayed on the operation panel.

Solution CAUSE: The HDD s corrupt. SOLUTION: Format the HDD by perfoming the following procedure: 1. Enter Tech Rep Mode. 2. Select IP HDD Format. 3. Select IP HDDFormat and press the Start key. 4. When prompted power the machine OFF/ON. SPECIAL NOTE : Solution contribution by Mark D'Attilio, Production Print/SSD


Description SC77-02.

Solution CAUSE: Failed M3 tray lift motor. SOLUTION:Replace M3 (p/n 15JK R704 00). SPECIAL NOTE : Solution contribution by David Aekus, Production Print/SSD


DescriptionADDRESS INPUT is grayed out on the operation panel and no E-mail addresses can be added.

Solution CAUSE: The option to allow the entering of the new address is set to Prohibit. SOLUTION: To allow the setting of new E-mail addresses perform the following: 1.Enter Admin Mode.2.Press System Settings.3.Press Prohibit User Operation.4.Select Registration and Change Address.5.Select ALLOW. SPECIAL NOTE : Solution contribution by Mark D'Attilio, Production Print/SSD


DescriptionUnable to enable a bizhub PRO 920 in Printgroove Queue.

Solution CAUSE: SNMP is not enabled on the bizhub PRO 920. SOLUTION: Enable SNMP on the bizhub PRO 920. 1. Press Utility/Counter button. 2. Press Administrator Setting and enter the administrator password (default password 12345678). 3. Press Network Setting. 4. Press IP NIC Setting. 5. Press Next until PSWC is displayed. 6. Press PSWC. 7. Press USE then OK. 8. Press Next or Back until SNMP is displayed. 9. Press SNMP. 10. Press Use then OK. 11. Exit Administrator mode and reboot the machine.

81



SPECIAL NOTE : Solution contribution by Ed Bellone, Production Print/SSD


DescriptionSC53-11 followed by SC24-03.

Solution CAUSE:Drum claw solenoid (SD4) failed or the wiring going to it is damaged causing ICP19 to fail on the PRCB. SOLUTION:Inspect and repair the wiring going to the drum claw sensor.If the wiring is OK replace the PRCB (p/n 57GA-9022F) and SD4 (55VAR72600) as aset. SPECIAL NOTE : Solution contribution by Jim Behrends, Production Print/SSD


DescriptionSC46-25 after servicing the MFP.

Solution CAUSE:The Overall Control Board was replaced andthe flatcable from the CCD to the rear of the OACB was not reconnected or improperly connected. SOLUTION:To inspect, remove the top cover that is to the right of the glass. Inspect the connection of the cable to the rear of the OACB. Reconnect thecable or ensure the connection is correct. SPECIAL NOTE : Solution contribution by Bob Moeller, Production Print/SSD


DescriptionThe Key Pad and Touch Panel are unresponsive except for the Power Save button. The machine does not beep when the Key Pad and Touch Panel arepressed. The machine will still print if it is equipped to do so.

Solution CAUSE: One of the buttons on the Key Pad is stuck or damaged. SOLUTION: Locate and free the stuck button. If the switch for the button is damaged replace the Operation Board/1 (p/n 57GA-903 1F). SPECIAL NOTE : Solution contribution by Ian Lynch, Production Print/SSD


DescriptionUnable to access Tech Rep Mode and Enter CE password is displayed on the operation panel. The CE password does not work.

Solution CAUSE:The NVRAM has failed. SOLUTION:Please contact the SSD Hotline to open a ticket and receive authorization to replace the NVRAM. Note : NVRAM ordering procedure is attached. To viewthe PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from theAdobe® web site at: http://www.adobe.com/products/acrobat/readstep2.html . SPECIAL NOTE : Solution contribution by Mark D'Attilio, Production Print/SSD


DescriptionLU-404 greyed out; not recognized.

Solution CAUSE:Machine has isolated the LU-404 from operation due to a technical problem by setting Software Switch 18-3 to1.

82



SOLUTION:To set Software Switch 18-3 to0, perform the following procedure: 1. Enter Tech Rep Mode. 2. Select System Input. 3. Select Software Switch Setting. 4. Select Switch 18-3. 5. Select 0, then select Return. 6. Exit Tech Rep Mode and cycle the machine power. SPECIAL NOTE : Solution contribution by Gregg Gallant, Production Print/SSD


Description Unableto printTIFF files using PageScope Direct Print.

Solution CAUSE: The compression method used is JPEG (JFIF) and the print controllersdo not support JPEG (scanner compression method). SOLUTION: When printing a TIFF file using PageScope Direct Print, please use the G3 (MH) or G4 (MMR) scanner compression methodby changing DipSW43. DipSW 43-0 = 0 G4 (MMR) 43-0 = 1 G3 (MH) Note :G3 is MH (Modified Huffman)and G4 is MMR (Modified Modified Read).MH is a one-dimensional encoding scheme that compresses each horizontalscan line of the image. MMRis atwo-dimensional encoding scheme that makes use of the high degree of vertical correlation between each scan line in the fax image to achieve ahigher compression than MH. SPECIAL NOTE : Solution contribution by KMBT (Japan).


DescriptionAll print jobs print without any user logged into Equitrac©.

Solution CAUSE: Incorrect software switch settings. SOLUTION: Set the Software Switches 9-0 to0, 9-1 to 1 and 16-3 to 1: 1. Enter Tech Rep Mode. 2. Select System Input. 3. Select Software Switch Setting. 4. Select eachswitch as listed above. 5. Enter the appropriate value for each switch as listed above. 6. Exit Tech Rep Mode and cycle the machine power. SPECIAL NOTE : Solution contribution by Gregg Gallant, Production Print/SSD


Description SC80-11 code. Unable to flash the firmware.

Solution CAUSE: The PRCB failed. SOLUTION: Replace the PRCB (p/n 57GA-9020). SPECIAL NOTE : Solution contribution by Mark D'Attilio, Production Print/SSD


Description

83



FS-604, "Please wait finisher operating" message. When finisher is removed message changes to "Press start to restart".

Solution CAUSE: Toner sensor located in the drum assembly may be dirty or may have failed. SOLUTION: Check the toner sensor (TCSB) located in the drum assembly; if dirty clean it and if determined as failed, replace the sensor board (p/n55VA-9510). SPECIAL NOTE : Solution contribution by Larry Kotar, KMBS/White Plains NY


DescriptionSC41-01 at power up.

Solution CAUSE: The DCPS/2 or the Scanner drive board has failed. SOLUTION: Repalce the DCPS/2 (p/n 57GB84520) and or the Scanner driver board (p/n 56GA-9090). SPECIAL NOTE : Solution contribution by Mark D'Attilio, Production Print/SSD


DescriptionPostScript driver not working.

Solution CAUSE: PostScript kit has not been installed. SOLUTION: Install the PostScript 3 Upgrade kit. bizhub PRO 920 - PS-503 (Item #15RL) bizhub PRO 950 - PS-504 (Item #A10R011) SPECIAL NOTE : Solution contribution by Mike McCarthy, Production Print/SSD


Description SC46-12 only when using 11x17 paper, reduced to 97% and selecting full scan image.

Solution CAUSE: The NVRAM has failed. SOLUTION: Contact the SSD Hotline to open a ticket and receive authorization for a replacement NVRAM. SPECIAL NOTE : Solution contribution by Mark D'Attilio, Production Print/SSD


DescriptionAPS does not work.

Solution CAUSE: Paper tray is set for a special type of paper. SOLUTION: Set paper tray for Normal paper: 1. Enter Admin mode. 2. Select System Settings. 3. Select Paper Settings. 4. Select Tray Settings. 5. Select the tray being printed to and select Change. 6. Ensure the Type is set to Normal, Colored Paper is set to White andHole Punch is set to NON. 7. Exit Admin mode. SPECIAL NOTE : Solution contribution by Gregg Gallant, Production Print/SSD

84




DescriptionOn a vCare-enabled MFP, the start button continually flashes amber.

Solution CAUSE: Thisoccurs if a technician did not press the "Maintenance Completion" button when exiting the MFP’s vCare/CS Remote Care settings in Tech RepMode. This isa normal function, which alerts the vCare system that vCare settings have been configured at the MFP, but may not have been fully completed. SOLUTION: If the blinking start key is related to vCare/CS Remote Care settings, use this proceudre: 1.Enter the MFP's Tech Rep mode: Press theUtility/Counter button. Press the[Details] button Press Stop, 0. 0,, Stop, 0, 1. 2. Press [CS Remote Care]. 3. Press the "Maintenance Completion" button. 4.Exit Tech Rep mode. Note: For certain MFP models, this symptom also canoccur when it necessary to replace a board.Consult the Field Service Manual and this Knowledgebaseif the symptom is not related to vCare/CSRC settings. SPECIAL NOTE: Solution contribution by Mark Kemp, ASG/SSD


DescriptionSC80-02 at powerup or after one print.

Solution CAUSE: Communication error between the PRCB and the OACB. SOLUTION:Power cycle machine main power.Replace the PRCB (p/n 57GA-902-0). SPECIAL NOTE : Solution contribution by Mike McCarthy, Production Print/SSD


DescriptionIntermittent SC46-36 codes when making booklets.

Solution CAUSE: The Printer Control Board has failed. SOLUTION: Replace the PRCB (p/n 57GA-9020). SPECIAL NOTE : Solution contribution by Mark D'Attilio, Production Print/SSD

85


bizhub PRO 920


DescriptionWhere is the key counter located?

SolutionThe key counter is located on the rear of the machine above the 2 ozone filters. To access the key counter remove the main rear panel, remove the metalbracket and withdraw the 4 pin key counter.


DescriptionHow to adjust for light density, poor fill.

SolutionPerform the procedure to improve solid density on single or duplex copies .Note: To view the above PDFs, Acrobat* Reader must be installed. Acrobat Reader can be downloaded for free from the Adobe* Web site at:[[http://www.adobe.com/products/acrobat/readstep2.html| URL http://www.adobe.com/products/acrobat/readstep2.html]]

* Trademark ownership information


DescriptionLow density/light image on long runs when running high percentage of coverage originals.

Solution CAUSE:A 30% to 50% or greater image coverage perpage. SOLUTION: See attached document to improveimage density when running high percentage of coverage originals.Topics addressed are: 1. How to reduce toner spill. 2. How to increase image density. 3. How to prevent density reduction during continuous print. 4. How to prevent density reduction during high coverage print. 5. How to reduce background. 6. How to prevent halo effects around outline characters in halftone or solid black image. 7. How to prevent density difference between side 1/side 2 and poor transfer on side 2. Note : To view the document(s), Microsoft® Word® or Word® Viewer must be installed. Word® Viewer 2003 (11.7MB) can be obtained free fromMicrosoft® at the following URL;http://www.microsoft.com/downloads/details.aspx?DisplayLang=en&FamilyID=95e24c87-8732-48d5-8689-ab826e7b8fdf .


DescriptionCopying process continually cycles ON/OFF without ever feeding a sheet of paper after pressing the START key. Unable to output copies or internal testprints. No jam or error code is displayed.

SolutionCAUSE: Firmware bug with version Control 12 and Image 20. The charge and the T/S auto cleaning have been disabled in the 25 mode.

SOLUTION: As a temporary fix, ensure that the charge and the T/S auto cleaning are enabled in the 25 mode, DIP SW 3, BIT 3 and 4 set to 0.


DescriptionAfter installing the print driver (PCL or PostScript) on Microsoft® Windows Vista™, the User Authentication/Account Track selection is unavailable.

Solution To enable User Authentication/Account Track in the print driver, perform the following: 1. Enter the Printer Properties of the driver. 2. Select the Configure tab. 3. Under Device Option, select the desired mode (User Authenticationor Account Track). 4. Enable the option in the drop down below Device Option. 5. Select Apply. 6. Verify that User Authentication/Account Track is available.

86


bizhub PRO 920


DescriptionLU404, how to program the paper size of the LCT.

SolutionTo program the size of the paper loaded in the LCT, perform the following:1. Power the copier ON.2. Press the Utility/Counter key on the operation panel.3. Press stop-00-stop-01.4. Touch [System Input] on the touchscreen.5. Touch [Standard Size] on the touchscreen.6. Select the key of changed paper size and touch the OK key.


DescriptionHow to default small size originals to 8.5x11.

SolutionTo default small size originals to 8.5x11, perform the following:1. Press the Utility button.2. Press Admin setting.3. Press System setting.4. Press Size setting.5. Under size setting change the default to 8.5x11.


DescriptionWhen trying to use the HDD to PC function in copy mode, there is no place to input the address or path to the PC.

SolutionCAUSE: HDD to PC scanning in copy mode is direct connect only.

SOLUTION: The destination PC must be connected to the printer via cable.


DescriptionThe manual bypass tray does not read the correct paper size.

SolutionCAUSE: The manual bypass tray adjustment was not done correctly during set up.

SOLUTION: When performing the manual bypass tray set up adjustment in the tech rep mode, both adjustments must be run. For the first adjustment, themanual bypass tray must be set to 210 mm and for the second adjustment it must be set to 280 mm.


Description'Please load 8.5X11 paper' message whenoriginal is copiedoff the platen glass or from the RADF.All paper trays are loaded with the correct size paper.

Solution CAUSE: The Auto Paper Type Selection does not have the Normal Option selected. SOLUTION: To change the paper type to Normal,perform the following: 1. Press the Utility Key. 2. Press Function Setting. 3. Select Auto Paper Type Selection. 4. Ensure Normal is Highlited.


DescriptionProduct Specifications, 920.

87


bizhub PRO 920

Solution 920 Product Specifications .Note: To view the PDF, Acrobat* Reader must be installed. Acrobat Reader can be downloaded for free from the Adobe* Web site at:[[http://www.adobe.com/products/acrobat/readstep2.html| URL http://www.adobe.com/products/acrobat/readstep2.html]]



DescriptionHow to have print jobs output with Account Track or User Authentication enabled.

SolutionTo have print jobs print without entering Account Track or User Authentication information into the print driver, please perform the following:

1. Enter Administrator Mode.2. Press User Authentication/Account Track.3. Press Non Register/Output Set4. Press ON


DescriptionUnable to 3-hole or 4-hole punch; machine will only 2-hole punch regardless of the mode selected.

SolutionCAUSE: Punch control board sensors not adjusted properly.

SOLUTION: Adjust all 5 potentiometers on the punch control board to the point where the corresponding LEDs come on, then one detent beyond that point.


DescriptionLight/washed-out section from lead-to-trail edge when copying or printing. Issue also occurs in test patterns: [[test pattern 5| URLhttp://techweb.konicabt.com/tpm/mfiles/testpattern5.pdf]] and [[test pattern 9| URL http://techweb.konicabt.com/tpm/mfiles/testpattern9.pdf]]

SolutionCAUSE: The machine is located too close to a window. Sunlight is leaking into the drum cavity from the right side of the machine.

SOLUTION: Relocate the machine away from the light source.


DescriptionHow to create a device printer on an AS/400™ system using the stock Konica MinoltaKN or NIC print server.

SolutionThe following models will support installation as a device printer using the OS/400™ SNMP setup with the imbedded NIC or KNxxx print server:IC-202IP-422IP-423IP-432IP-511IP-602These models support a setup that will allow a device printer to be created on the AS/400™. When printing SCS, this setup can be used with the stockcontroller NIC cards. This setup supports page range control but does not support specific tray calls. In order to support tray call the AS/400™ workstationcustomization table (if there is one) must be modified.To load an SNMP driver compatible with the Konica IP unit, perform the following:1. From the Main Menu under Selection or Command, type:crtdevprt 2. Change the following to set up the printer (those settings not changed, keep at default): a. Device Description - (name the printer i.e., Konica Minolta) b. Device Class - *LAN c. Device Type - 3812 d. Device Model - 1 e. LAN Attach - *IP f. Port number 10001 (IP-432 = 9100) note: use the port number that prints out on the NIC status page. g. Font Identifier - 011 h. Form Feed - * Autocut

88


bizhub PRO 920

i. Manufacturer - *HP5si j. Paper Source (both) - *letter k. Address - (TCP/IP address of the NIC) l. System Driver (hit F4) - *IBMSNMPDRV Note : Vary ON the device to allow attachment.


DescriptionExcessive toner in the cleaning section of the 920

SolutionPerform the procedure listed belowit will resolve the excessive toner problem.

Solid density procedure for single or duplex copies on the 920

1. Verify dip switches and Black ratio average

DIPSW No Bit Function Default setting Inch

2 1 All charger cleaning cycle (fixing temperature 50°C or less when turning ON) 0 2 0 3 0 4 All charger cleaning cycle (after turned ON) 0 5 0 DIPSW 3 3 Charger cleaning function 0 4 Transfer/separation charger cleaning function 0 DIPSW 5 2 Image density selection (laser PWM) for copier 0 3 0 DIPSW 6 0 Background density adjustment (photo mode) 0 1 1 2 Transfer assist control 0 3 Minimum black band width 0 4 0 5 Image stabilization control cycle 0 6 1 7 Drum potential auto adjustment 0DIPSW 7 0 Developer type (new/old) 1 2 Background density adjustment 0 3 0 DIPSW 8 0 Image density selection (laser PWM) for printer 0 1 0 DIPSW 23 2 Toner density of developer selection 0 3 0 4 0

DIPSW 27 2 Image density selection (toner control patch density) 0 3 0 5 Thin characters reproduction improvement (usage of smaller laser dot) Standard Thin-character Correspondent 0

[06 Pixel ratio of each section]

Pixel Ratio Data List average Classification1~2% Low coverage2~4% Low to avg. coverage4~6% average coverage6~8% average to lower high coverage8% or above High coverage

2. Check and change value of the transfer current setting 02 Process Adjustments01 High Voltage Adjustment01 High Voltage Auto Adjustment 03 HV Adjustment (Transfer) Value XX

Note the setting and reduce this setting by 2 to 3 steps. For example: If it is 45 set it to 42.

89


bizhub PRO 920

3. Run the auto high voltage adjustment02 Process Adjustment01 High Voltage Adjustment01 High Voltage Auto Adjustment

4. For the following conditions set dipsw to the following4~8% average .25% increase in toner to carrier ratio

DIPSW 23 2 Toner density of developer selection 0 3 0 4 1

DIPSW 27 2 Image density selection (toner control patch density) 0 3 0 5 Thin characters reproduction improvement (usage of smaller laser dot) Standard Thin-character Correspondent 0 8% or above average .5% increase in toner to carrier ratio*

DIPSW 23 2 Toner density of developer selection 1 3 0 4 1

DIPSW 27 2 Image density selection (toner control patch density) 0 3 0 5 Thin characters reproduction improvement (usage of smaller laser dot) Standard Thin-character Correspondent 0* If background occurs return dipsw 23-2 to "0"5. Press return and select process adjustment and perform the following adjustments:

02 Process Adjustment02 Drum Peculiarity Adjustment 03 Auto Maximum Density Adjustment04 Auto Dot Diameter Adjustment 05 LD Offset Adjustment 06 Auto Gamma Adjustment (1dot)

6. Select test mode

06 Test Mode 02 Test Pattern Density =25501 Test Pattern Output Mode7. Run 200 copies 1:2 of test pattern #12 on 8.5 x 11 paper.8. Verify fill of black squares on front and back side of page for density.

Note: some lower grades of paper will not completely fill black squares regardless of the adjustments made due to paper characteristics.

9. Press service button and select process adjustment and rerun the following adjustments:

02 Process Adjustments02 Drum Peculiarity Adjustment03 Auto Maximum Density Adjustment04 Auto Dot Diameter Adjustment 06 Auto Gamma Adjustment (1dot)


DescriptionHow to load 32 bit XP drivers on a Windows* 2003 64 bit server for driver migration to the 32 bit clients.

Solution32 bit driver files are not recognized when attempting to load on a 64 bit system, therefore the files must be pulled from a 32 bit system in order to addadditional driver support on a 64 bit server.

1. After installing the PCL, PS(Visual), PS(Plug-in) or PS(Adobe*) driver on the server, install the same type driver (32 bit version) on one of the clients.

90


bizhub PRO 920

2. The driver files will be placed in C:\WINDOWS\inf folder on the client.3. Share this folder on the network so that the 64 bit server has access.4. From the server, when adding additional drivers, browse to the shared folder on the workstation5. Select the appropriate .inf file from the shared folder on the client - the driver files will then be pulled over to the server to support other 32 bit clients whenmigrating the driver files.

Note: It is important to install the same type of driver on the client to match the driver installed on the server.



DescriptionTime to acquire scan is excessive; slow scanning.The 'Connecting' message lasts a long time.

Solution CAUSE: Scanning may seem slow because the TWAIN driver is searching for all available machines to scan from on the network. SOLUTION : When the Select Devices dialog box is displayed, select 'from registered devices' and also select 'Use this device for future session'option.Please see attachment for procedure. Note : To viewthe PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:http://www.adobe.com/products/acrobat/readstep2.html . SPECIAL NOTE : Solution contribution by Cesar Jimenez, Production Print/SSD


Description Setting SNMP v1/v2c “read/write community” names through PageScope Net Care.

Solution Changing the read and/or write SNMP "community names" can be implemented as a security measure through PageScope Net Care. Please see attacheddocument for instructions. Note : To view a PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at: http://www.adobe.com/products/acrobat/readstep2.html


DescriptionIn the event that an issue arises that requires immediate action by the technician, certain NVRAMs may be exchanged/swapped between units due to theircompatibility with other models.

Solution The following groupings of main bodies are compatible for NVRAM exchange with others within their group only in emergency situations or fortroubleshooting purposes : 7145/7222/7228/7235 bizhub 200/250/350 bizhub 360/420/500 bizhub 600/750 7155/7165/7085 7210/7255/7272/bizhub PRO 920/bizhub PRO 1050 C250/C252/C300/C351/C352/C450 C451/C550/C650 IMPORTANT : A new NVRAM should be obtained as soon as possible for the machine requiring one. Notes : 1. The bizhub C350 NVRAM may only be used between other bizhub C350s. 2. CAUTION : The bizhub PRO C500/8050 NVRAMs may not be exchanged between units due to the serialization of the NVRAM. SPECIAL NOTE : Solution contribution by Ed Bellone, Production Print/SSD

91


bizhub PRO 920


DescriptionIntermittently the NIC drops off the network.

Solution CAUSE: SNMP is enabled and causing the NIC to drop offline. SOLUTION: Disable SNMP by performing the following: 1. Pres the Utility key. 2. Press Administrator and enter password. 3. Press Network Settings. 4. Press IP NIC. 5. Press SNMP and select Not Use.


DescriptionList of equipment that is no longer being supported.

Solution Please see attached Product & Technical Support Bulletins 1792 and 2443 andMarketing Bulletin#07-GB-016. Note : To view a PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at: http://www.adobe.com/products/acrobat/readstep2.html


DescriptionCountermeasure against decrease of trace of Drum separating claw.

SolutionSee KOM050849.pdf for details.Note: To view the above PDF, Acrobat* Reader must be installed. Acrobat Reader can be downloaded for free from the Adobe* Web site at:[[http://www.adobe.com/products/acrobat/readstep2.html| URL http://www.adobe.com/products/acrobat/readstep2.html]]



DescriptionSystem Configurator, 920.

Solution 920 System Configurator .Note: To view the PDF, Acrobat* Reader must be installed. Acrobat Reader can be downloaded for free from the Adobe* Web site at:[[http://www.adobe.com/products/acrobat/readstep2.html| URL http://www.adobe.com/products/acrobat/readstep2.html]]



DescriptionCan the developer for the 7085 be used in a bizhub PRO 920?

SolutionThe developer used in the bizhub PRO 920 (Item #022B) is exclusive to this model only.


DescriptionCan the drum for the 7085 be used in a bizhub PRO 920?

SolutionThe drum used in the bizhub PRO 920 (Item #022H) is exclusive to this model only.

92


bizhub PRO 920


DescriptionTotal count reset procedure, bizhub 920.

SolutionA KMBS policy change effective November 2004 prevents provision of information regarding electronic counter reset procedures for all current and futureproducts due to liability involved with potential fraud. The concern is that counters will be reset and the engine sold as new.


DescriptionSC21-01, SC21-03 is displayed

SolutionCAUSE: Malfunction of the cleaning operation of the charging corona or transfer/separation corona caused by a firmware bug.

SOLUTION: Update to current firmware levels.


DescriptionCountermeasure against transfer jitter (ADU drive board assy).




DescriptionWhat is the main body Web Utilities Machine Manager setting user name and password?

SolutionThe Machine Manager setting user name is 'admin' and the password is '00000000'.


DescriptionHow to set the paper tray priority.

SolutionTo set the paper tray priority, perform the following:1. Power the copier ON.2. Press the Utility key on the operation panel.3. Touch [2. Function Setting] on the touchscreen.4. Touch [1. Feed Tray Setting] on the touchscreen.5. Touch [1. Feed Tray Auto Select] on the touchscreen.6. On the left hand side of the touchscreen, touch to highlight desired tray key, for each tray which is to be automatically detected when ATS/APS functions.If, the tray key is not highlighted it will not be an ATS/APS available tray, nor will it be displayed on the right half of the touchscreen.7. Tray keys specified as ATS/APS ON will appear on the right half of the touchscreen. Touch to highlight the desired tray key, and then change its priority byusing the up-down arrow keys.8. Touch [OK] on the touchscreen to complete the setting.9. Touch [Exit] on the lower left corner of the touchscreen to return to the normal copy mode.


DescriptionHow to enter the touchscreen adjustment when the touchscreen is out of adjustment.

SolutionTo enter to touchscreen adjustment, perform the following:

93


bizhub PRO 920

1. Select the [Utility] button.2. Select number 5 on the key pad.


DescriptionLU403, how to program the paper size of the LCT.

SolutionTo program the size of the paper loaded in the LCT, perform the following:1. Power the copier ON.2. Press the Utility/Counter key on the operation panel.3. Press stop-00-stop-01.4. Touch [System Input] on the touchscreen.5. Touch [Standard Size] on the touchscreen.6. Select the key of changed paper size and touch the OK key.


DescriptionBanding is occurring on the paper in the front-to-rear direction approximately 1 inch apart and the bands are 2mm in width.

SolutionCAUSE: The cleaning blade is skipping causing the banding.

SOLUTION: Replace the cleaning blade.


DescriptionHow to retrieve copies or password print jobs stored to HDD (box).

SolutionCopied data stored on the internal HDD with the [Store] screen or confidential print jobs transmitted from a computer can be output using the [Recall] screen. 1. Press [Box] on the control panel and then press [Recall] key.2. Specify the folder in which the data you output are stored. Press the [Personal Folder] key to display the list. Select any folder and press the [OK] key. Press the [Public Folder] key. Press the [Confidential] key. A Password may be configured for the Personal Folder. In that case, the Password input screen appears. Enter the Password. If you know the target file, press the [Direct Call] key to specify the location directly.Using "File Combination" Jobs that are stored to a box can be reprinted in groups of up to 5 at a time.


DescriptionLU403 registers as 11x17 and is only capable of 8.5x11.

SolutionCAUSE: An anomaly in the program requires the LU403 tray size setting to be changed to a different size paper and then back to 8.5x11.

SOLUTION: Perform the following procedure to set the LU403 to standard 8.5x11 paper:1. Enter the Tech Rep mode by pressing the Utility key and then S,0,0, S,0,1.2. Select System Input.3. Select Size Setting Tray 4.4. Select Standard Size.5. Select A4 and return to normal copy mode.6. Perform steps 1 thru 5 but this time select 8.5x11 as the LU403 paper size.


DescriptionIs the bizhub 920 PostScript* (P) driver Microsoft*-certified?

SolutionThe bizhub 920 PostScript (P) driver is Microsoft-certified. Microsoft-certified drives are listed on the [[Windows Marketplace Tested Products List| URLhttp://testedproducts.windowsmarketplace.com/results.aspx?&text=Konica%20Minolta&bCatID=0&cpID=0&ocID=0&OR=1&PG=1]].

94


bizhub PRO 920

Note: Scroll through the available pages to obtain a complete listing of Konica Minolta Microsoft-certified drivers.



DescriptionUnable to browse to the IP NIC and 'Page can not be displayed' is indicated in the browser.

SolutionCAUSE: PageScope Web Connection is not enabled.

SOLUTION: To enable PageScope Web Connection, perform the following:1. Press the Utility key.2. Press Administrator mode and enter the password.3. Press Network Settings.4. Press IP NIC.5. Press NEXT and then select #13 PSWC. 6. Press USE and then Close until the main copy screen is displayed.


DescriptionHow to set up Color/Black & White Splitting with MicroPress®.

Solution For Color Splitting, MicroPress® version 7.0.0.6 or greater must be running on the bizhub PRO 920 and MicroPress® version 7.0.0.8 or greateron the bizhubPRO 1050 to use the Post Inserter.This feature creates a copy of each monochrome page of a job and routes these pages to the Monochrome Spool printer in the Input Controller. A placeholder for the color pages is automatically generated. The monochrome printer should be set to Hold. This will allow the color pages to be printed and thenplaced in the post process inserter to rebuild the job on the fly.1. From the MP_Rip menu, Stop Inputs.2. Select Page Setup Manager.3. Select the Page Setup for the color device you want to modify. Then select Copy.4. Check the Enable Feature box under the Processing section.5. In the pull-down window below the Enable Feature box, be sure that the SplitColorJob is selected.6. Click Save as to exit this menu. Name the new Page Setup ColorSplit Printer.7. Close Page Setup Manager.8. Open the Input Controller.9. Edit the MonochromeSpool.10. For Page Setup, select the monochrome printer that will process the Black and White pages.11. Make sure to put a check in the box next to Enable before Selecting OK and closing the Input Channel Edit.12. To Publish the new printer, close down the RIP and MicroSpool™. Then restart the RIP and then MicroSpool™.13. Go to the Black and White printer in PrintStation™ Manager, double-click on it and go to the device tab. Scroll down to Color Insertion tray and set up theproper tray.14. Once a job is sent to the ColorSplit printer, all the color pages will print on the selected color printer. In PrintStation™ Manager, go to the color split jobbeing held on the color printer, right-click on the job and go to Info. 15.Select the Output Option tab and then select Insert Color Pages. 16.Release the job once the color inserts from the color printer have been put in the proper tray on the Black and White machine.


DescriptionServer Connect error message when scanning to E-mail. Both locations can see users in LDAP look up. The first location there were no issues whensending E-mail. The second location would give Server Connect error.

SolutionCAUSE: Two locations are connected via 100MB metro ethernet WAN. The timeout was set to max. The customer has two E-mail servers; one at each site.

SOLUTION: Change the SMTP mail server address to the local mail server.


DescriptionIs the IC203 required in order to scan to E-mail, FTP or PC (SMB)?

SolutionThe IC203 is required in order to support scan to E-mail, FTP or PC (SMB).

95


bizhub PRO 920


DescriptionHow to set the bizhub 920 so the PI501 punches 3 holes when paper inserted/fed from it.

SolutionEnter the Utility Mode, select controller, then select printer setting and select basic setting. Select #7 Punch setting. The choices are OFF, 2, 3 hole. Makethe selection needed.


DescriptionWhat are the usernames and passwords for the mainbody NIC?

SolutionThe username for the maintenance side of the NIC is ce. The password is 92729272.The username fior the machine mgr. side of the NIC is admin. the password is 8 "0" 's.


Description Unable to install 32-bitdrivers on a Microsoft Windows 2003 64-bit server formigration to the 32-bit clients.

Solution The 32-bit driver files are not recognized when attempting to load on a 64-bit system, therefore, the files must be pulled from a 32-bit system in order to addadditional driver support on a 64-bit server: 1. After installing the 64-bit driver on the server, install the matching 32-bit(PCL, PostScript Visual, PostScript (Plug-in) or PostScript (Adobe) driveron one ofthe clients. 2. The driver files will be placed in C:\WINDOWS\inf folder on the client. 3. Share this folder on the network so that the 64-bit server has access. 4. From the server, when adding additional drivers, browse to the shared folder on the workstation 5. Select the appropriate .inf file from the shared folder on the client - the driver files will then be pulled over to the server to support other 32-bit clients whenmigrating the driver files. Note: It is important to install the same type of driver on the client to match the driver installed on the server.


Description FS509/FS604, PULL OUT FINISHER STACKER AND CHECK STAPLER message when selecting staple mode.

Solution CAUSE: The add stapler sensor has failed. SOLUTION: Replace the failed stapler unit (p/n 15JM-5010).


DescriptionScan to FTP using a host name versus a TCP/IP address is not working in a workgroup environment.

Solution CAUSE: A DNS server is required when using a host name versus the TCP/IP address. SOLUTION:If no DNS server is available, then a TCP/IP address must be used instead of the PC host name.


DescriptionPart number for the mounting kit needed for the installation of the RC-501 toner recycle kit.

SolutionMounting kit needed for the installation of the RC-501 toner recycle kit (p/n 57GA-K010).

96


bizhub PRO 920


Description Howto createAccount Track accounts remotely using a browser.

Solution To create a large number of accounts in Account Track using an internet browser, follow these steps. This is faster and easier than creating them throughthe 920 control panel. It has been tested with up to 200 accounts. 1. Enable Account Track on the 920 using its control panel. a. Utility/Counter b. Administrator Setting c. User Authentication d. General Setting e. User Authentication f. User Authentication = OFF g. Account Track = ON h. Account Name = OFF i. Account Distribution Number = 1000 j. Account Track k. Copier/printer = USE l. Scanner = USE m. OK, Close, Close, Close. 2. Create at least one account using the 920 control panel. 3. Export the account list from the 920 to a local computer. a. With a browser, connect to the 920 b.Using the web browser, go to Machine Manager Setting c. Login to the 920. Login Name = admin; Password =12345678 d.Setting Data Import/ Export e. Account Track Data (Tab Separated) f. Export g. Save the resulting file (vt_tab.txt) 4. Edit the exported file using Microsoft Windows Notepad or another text editor. a. Addusers as follows: password [TAB]username [TAB]0 [Enter] b. Repeat step (a) for each user. See the following example of an edited file. c. Save the file. 5. Import the edited file back to the 920. a.ClickImport. b. Browse to the edited file on the local computer. c.ClickImport.


Description Who to contact for parts and technical supportconcerning Jamex™ products.

Solution Support is provided by Jamex™ by calling 800-289-6550. Refer to attached Marketing Bulletin #04-GB-016 for more detail. Note : To view a PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at: http://www.adobe.com/products/acrobat/readstep2.html


DescriptionThe operation panel is 'locked up', machine cannot be flashed and continually runs.

97


bizhub PRO 920

Solution CAUSE: The operationboard has failed. SOLUTION: Replace the operation board (p/n 57GA-9030).


DescriptionWhen searching solutions by models,referenced links for the documentsare notaccessible.

Solution CAUSE: This is a search of the printed database. The links are locatedwithin the solution in the database. SOLUTION: Copy the solution ID number into the Knowledgebase look-up Keyword field and select Search to access the solution complete with active linksto attached documents. Note : If there is an actual 'dead' link within the solution, please send an E-mail to [email protected] with the solution ID number and pleaseidentify the link.


DescriptionWhen scanning to the network (E-mail, FTP, SMB, HDD) and the scan completes, the file name that is displayed will remain until it is changed or the machineperforms an automatic reset.

Solution CAUSE: Firmware upgrade required. SOLUTION: A firmware change has been issued whichallows a procedure to be performed toclear the file name after the scan completes.Firmware versionmust be at least the following to allow this function: bizhub PRO 1050/1050e - version 50 bizhub PRO 920 - version 40 Once the firmware is installed, set DIPswitch 21-7 to 1. With DIP 21-7 set to 1, the user must press theReset key after the scan completes to clear the filename. Note : The latest versionof firmwareis available on the Konica Minolta Download Selector. Access the Selector from SSD Web Support (CS Expert Support)by clicking on 'Download MSDS, Drivers, Firmware and more'.


DescriptionWill PageScope Direct Print support PDF version 1.6?

Solution PDF version 1.6 is notsupported by PageScope Direct Print on the bizhub PRO 920/1050 series.Therefore, please use PDF version 1.4 or 1.5. Note : The upcoming model releases will support PDF version 1.6.


DescriptionHow to configure tandem printing on the bizhub 920.

SolutionPREREQUISITESRequired firmware 920 mainbody version 12/20Required system code IC203 version 20; only one 920 must have a controller attached.Driver versions: PCL* version 2.0 or Visual PostScript* version 2.1.0.0Both machines must have the same finishing/tray options installed.

To configure Tandem printing follow the instructions described below.1. Verify DIPsw. 20-7 = 1. 2. Enter Utility mode then enter Admin. Settings. Input the password for access the default is 92729272. Select network setup. Select Mainbody/machineNIC.3. Input the TCP/IP* address to be assigned to the mainbody NIC of this machine.4. At the bottom of the screen select Tandem NIC and input the mainbody NIC address that will be assigned to the other machine.5. Save the settings.6. Go to the other machine and follow steps 1 through 5.7. Go to the operational panel screen and select Tandem, select enable. This is done on both machines.8. To connect the mainbody NICs of the 2 machines either a crossover network cable is required or 2 straight cables and a hub are required. The network

98


bizhub PRO 920

connection goes to the machine with the IP controller attached.



DescriptionCan the toner for the 7085 be used in a bizhub PRO 920?

SolutionThe toner used in the bizhub PRO 920 (Item #022J) is exclusive to this model only.


DescriptionLU-403 will not hold the 4500 sheets outlined in the sales guide

SolutionThe capacity specification for the LU-403 has changed to 4000 sheets.


DescriptionFS509, with staple mode and small paper sizes, roller marks may appear on the side 2 of the 1st sheet in the 2nd and later sets of copies.

SolutionCAUSE: The bypass control, which holds the 1st sheet of each set of copies during the interval between sets, is performed in staple mode for securingproductivity. However, while the 1st sheet is waiting, it is rubbed with rollers and becomes soiled.

SOLUTION: Update Print Control to current levels and perform the following:

A switch to disable the bypass control under any condition has been provided. If roller marks appear at the position specified above, set the dipswitch 37-2 to1. However, with this setting, the productivity decreases slightly.

NOTE: If the above procedure does not resolve the problem a new style roller is available for no charge. Please contact Engineering to obtain this roller.


DescriptionWhat is Enhanced Security mode?

SolutionEnhanced Security mode ensures data protection when connected to the network. Enhanced Security offers the following protections: 1. Protects or deletes data that remains in memory or on the HDD after being processed. Enhanced Security mode ensures data are deleted completelybefore releasing the image area. 2. Secure passwords made up of 8 to 64 alpha numeric characters. 3. User Authentication is required to access boxes stored on the HDD. 4. External access is only permitted for the telephone lines with CS Remote Care.5. Audit logs are maintained with a history of security related events. Note: Enhanced Security mode is only available with an IC-203 installed.


DescriptionUser Authentication User Name and Password specifications.

SolutionUser Name and Password specifications: 1. User names are 1 to 64 alphanumerical characters. 2. Passwords are 8 to 64 alphanumerical characters.Notes: 1. Characters are case sensitive.2. Passwords of less than 8 characters are invalid. 3. If the wrong password is entered at authentication, the system will not accept retry for 5 seconds.

99


bizhub PRO 920


DescriptionWhat is the default PageScope Web Connection Administrator password?

SolutionThe default PageScope Web Connection Administrator password is 00000000.


DescriptionLDAP availability.

SolutionLDAP will not be available until phase 2 of the product (early 2006).


DescriptionFS509, how many sheets can be half-folded without using the staple option?

SolutionThe FS509 can only fold a maximum 3 sheets of paper when not using the staple option.


DescriptionHow to default the machine to be a PS interpreter only?

SolutionTo change the default interpreter to be PS only perform the following;1. Select [Utility].2. Select [CONTROLLER].3. Select [02 Printer Settings].4. Select [01 Basic Settings].5. Select [01 PDL].6. Select [PS].


DescriptionUnable to select tray 3 as Priority TRAY.

SolutionCAUSE: Tray 3 has not been select as the priority tray selection in the Function Settings menu.

SOLUTION: To select tray 3 as the priority tray perform the following;1. Select [Utility].2. Select [Function Setting].3. Select [Feed Tray Setting].4. Select [Feed Tray Auto Selection].5. Set tray 3 to be the priority tray.6. Power the copier OFF/ON.Note: Ensure the machine is set for current settings, and not Factory Settings.


DescriptionWhat is the best method to feed NCR type paper from the 920?

SolutionThe following settings should be used to ensure minimal problems when feeding NCR 3 part paper.1: It should only be feed from the LCT.2: The job should be sent in reverse order and output faceup.3: The paper type should be set for Thin paper.

100


bizhub PRO 920


DescriptionIC203, does the bizhub 920 require 2 controllers for Tandem printing?

SolutionOnly one controller is required for tandem printing.


DescriptionUnable to enter correct copy quantity.

SolutionCAUSE: Copy limit function is enabled.

SOLUTION: To program the copy quantity limit in the software switch setting mode, perform the following:1. With the copier powered ON access the service mode.2. Touch [System Input] on the touchscreen.3. Touch [Software Switch Setting] on the touchscreen.4. Scroll to dipswitch 9-4.5. Use the matrix below to determine which value inputs at DIPSW 9 (bits 4, 5, 6, and 7 should be entered to select the copy quantity limit desired by thecustomer):9-4 to 0 9-5 to 0 9-6 to 0 9-7 to 0: No limit9-4 to 1 9-5 to 0 9-6 to 0 9-7 to 0: Copy limit = 19-4 to 0 9-5 to 1 9-6 to 0 9-7 to 0: Copy limit = 39-4 to 1 9-5 to 1 9-6 to 0 9-7 to 0: Copy limit = 59-4 to 0 9-5 to 0 9-6 to 1 9-7 to 0: Copy limit = 99-4 to 1 9-5 to 0 9-6 to 1 9-7 to 0: Copy limit = 109-4 to 0 9-5 to 1 9-6 to 1 9-7 to 0: Copy limit = 209-4 to 1 9-5 to 1 9-6 to 1 9-7 to 0: Copy limit = 309-4 to 0 9-5 to 0 9-6 to 0 9-7 to 1: Copy limit = 509-4 to 1 9-5 to 0 9-6 to 0 9-7 to 1: Copy limit = 996. Touch the ON/OFF key to input the desired setting of 0 (OFF), or 1 (ON) for bit location 4.7. Scroll to bit 5.8. Repeat the procedure in steps 6 and 7 for dipswitches 9-5, 9-6, 9-7.9. Touch [Return].10. Touch [Exit].11. Touch [Close] to exit the software switch setting mode.


DescriptionReasons why the NIC might not connect to a Novell* NDS server when attempting to configure using queue-based printing (IPX/SPX).

Solution1. The SET 'reply to request for nearest server' setting is not enabled.2. Not enough licenses.3. Signature level not set between 0 - 2. Signature level 3 (packet encryption) is not supported.4. No autosense. If the NICs are bound to three or more LAN protocols, then the autosense of media type fails. Select a frame type manually.5. NDS and the local schema are corrupt and need to be repaired with DSRepair.6. Printer object is not set up as remote/unknown. Wipe all objects and recreate them with Quick Setup.7. The Disable Bindery setting is checked in the IPX setup on the NIC. It disables everything.8. Using autosense hubs. The port needs to be set up as a single speed or a single speed hub needs to be placed between the autosense hub and the NIC.9. The NIC is not advertising on the network. Use Display Servers command and view three instances of the KN card.10. If AppleTalk* is not needed, disable it. Both AppleTalk and Novell protocols are 'chatty'.



DescriptionCan the standard HDD1 be removed and the unit still function properly?

SolutionThe HDD1 can be removed from the machine and the unit will function properly with the exception of scan to box.

101


bizhub PRO 920


DescriptionHow to set Auto mode when an original is placed in the RADF.

SolutionTo set Auto mode upon RADF original detection, perform the following:1. Power the copier ON.2. Press the Utility key on the operation panel.3. Touch [Copier settings] on the touchscreen.4. Touch [Reset Setting] on the touchscreen.5. Touch [Reset Function] on the touchscreen.6. Set the following items:Auto reset by key setting - Initial SettingFinisher Mode by Full Auto - Sort

Also, verify that the reset initial setting is as followings:1. Press the Utility key on the operation panel.2. Touch [Copier settings] on the touchscreen.3. Touch [Reset Setting] on the touchscreen.4. Touch [Initial Setting] on the touchscreen.5. Select [Current]


DescriptionHow to set APS to default to tray 4 when copying from the glass.

SolutionTo set APS to default to tray 4 when copying from the glass, perform the following:1. Press the Utility key on the operation panel.2. Touch [Copier settings] on the touchscreen.3. Touch [Reset Setting] on the touchscreen.4. Touch [Initial Setting] on the touchscreen.5. Select [Current].

Also, verify that the reset initial setting is as followings:1. Press the Utility key on the operation panel.2. Touch [Feed Tray Setting] on the touchscreen.3. Touch [Feed Tray Auto Select] on the touchscreen.4. Touch [Initial Setting] on the touchscreen.5. Select - ATS/APS - All - Tray Priority - 4, 1, 2, 3, bypass


DescriptionDoes the bizhub PRO 920 support Bates Stamping?

SolutionThe bizhub PRO 920 has Bates Stamping capability.


DescriptionMicrosoft®-certified printer drivers - PCL, PostScript, PostScript (P)and PostScript (V).

Solution The Konica Minolta Microsoft®-certified printer driverscan bedownloaded fromthe Konica Minolta Download Selector. Access the Selector from theKMBSpublic site ( http://www.kmbs.konicaminolta.us ) Support & Drivers tab or from SSD Web Support (CS Expert Support) by clicking on 'Download MSDS,Drivers, Firmware and more'. These drivers will be shown as a WHQL ( W indows H ardware Q uality L abs)Download. Access the Download Selector and type WHQL in [Find downloads:],then click on Search->.


Description

102


bizhub PRO 920

Memory specifications.

SolutionThe bizhub 920 comes standard with 256MB. An optional 256MB memory stick is available (EM701 - Item #15BV).


DescriptionIs the bizhub 920 PCL* driver Microsoft*-certified?

SolutionThe bizhub 920 PCL driver is Microsoft-certified. Microsoft-certified drives are listed on the [[Windows Marketplace Tested Products List| URLhttp://testedproducts.windowsmarketplace.com/results.aspx?&text=Konica%20Minolta&bCatID=0&cpID=0&ocID=0&OR=1&PG=1]].Note: Scroll through the available pages to obtain a complete listing of Konica Minolta Microsoft-certified drivers.



DescriptionIs the bizhub 920 PostScript* (V) driver Microsoft*-certified?

SolutionThe bizhub 920 PostScript (V) driver is Microsoft-certified. Microsoft-certified drives are listed on the [[Windows Marketplace Tested Products List| URLhttp://testedproducts.windowsmarketplace.com/results.aspx?&text=Konica%20Minolta&bCatID=0&cpID=0&ocID=0&OR=1&PG=1]].Note: Scroll through the available pages to obtain a complete listing of Konica Minolta Microsoft-certified drivers.



DescriptionIn PageScope Job Spooler 1.5.0.7, can Active Jobs be held and reprinted in Job Spooler? Can completed jobs be reprinted?

SolutionActive jobs can only be changed in priority and not held. Completed jobs are only listed and can not be re-printed. Only by selecting in the driver for Outputmethod -Save in User Box, can documents then be retrieved through Job Spooler. They are retrieved by accessing the User Box through Job Spooler. Atthis point, Job Settings can be changed and the document reprinted from Job Spooler.


DescriptionHow to print the account management list.

SolutionTo print the account management list:1. Press the utility button.2. Press the administrator tab.3 Enter password.4. Press the System setting tab.5. Press print management list.6. Press audit log report.7. Press the copy tab.8. Press the start key.


DescriptionWhen copying in booklet mode, the image is rotated incorrectly.

SolutionCAUSE: Incorrect Booklet Copy settings.

SOLUTION: To correct this issue, perform the following:1. Press the Utility Mode on operation panel.2. Select Copier Settings.3. Select Each Function Setting.

103


bizhub PRO 920

4. Select Booklet Copy.5. Set to 'Manual'.


DescriptionHow to create a User's Folder from the touchscreen.

SolutionTo create a User's Folder from the touchscreen, perform the following:1. Touch [Box] on the lower left corner of the copy mode touchscreen.2. Select and highlight [Personal Folder] or [Public Folder].3. Touch [New Register].4. Touch [Folder Name] Input on the touchscreen. Enter the desired folder name.5. Touch [OK] on the touchscreen.6. Touch [Password Input] on the touchscreen. Enter the desired password.7. Touch [OK] on the touchscreen.8. Touch [OK] on the touchscreen.9. Touch [Cancel] on the touchscreen.10. Touch [Cancel] on the touchscreen to return to the normal mode.


DescriptionHow many bags of developer are used at start-up and at a PM?

SolutionThere are two bags inside of the one package of developer (02UK). Both are used at startup and at PM service.


DescriptionHow to set any paper tray as the default paper tray.

SolutionTo set paper tray 1 as the default paper tray, perform the following:1. Press the Utility Key.2. Select Copier Setting.3. Select Reset Setting.4. Select Initial Setting.5. Select CURRENT.6. Back out of the basic copy screen and select PAPER on the touchscreen.7. Select the desired paper tray and press OK.8. Select ZOOM.9. Press x1.0 and then OK.The tray is now programmed as the default.


DescriptionHow to set up LDAP so that user authentication is not required when performing an LDAP search.

SolutionTo set up LDAP so that user authentication is not required when performing an LDAP search, perform the following:1. Select SIMPLE for the Authentication Method.2. DISABLE User Authentication.3. Enter a Login Name and Password and press APPLY if making the changes via the web interface.4. An LDAP search can now be performed without the user having to authenticate.


DescriptionThe bizhub 920 stops printing jobs when sending a mixture of stapled and non stapled jobs from a UNIX* or main frame environment

SolutionCAUSE: There is a deficiency in the base firmware for the bizhub 920.

104


bizhub PRO 920

SOLUTION: Install the ABT0 patch to version 20 of the image control firmware on the bizhub 920. This patch is available on the [[Konica Minolta FTP site|URL ftp://kbtdigital:[email protected]]].



DescriptionHow to enable the jam counter

SolutionTo enable the jam counter, perform the following:1. Access the Tech Rep Mode.2. Select [System Input].3. Select [Software SW settings].4. Scroll to Dip SW 11, bit 7 and select [ON].


DescriptionUnable to select Hole-Punch and Tab paper when printing with the 920 PCL* driver; Constraint message is displayed when the two options are selected.

Solution CAUSE: This is normal operation, thebizhub 920 does not officially support the punching of tab paper which is considered a thick paper. This was verified with PCL driver version 02.00.00.01.

SOLUTION: Tab inserts much be pre-punched and fed fromPost Inserter unit. * Trademark ownership information


DescriptionUpon finishing a scan to E-mail job, the auto reset key does not bring the copy screen back to the scanning screen. The Address Icon on the touchscreenmust be pressed to return to the main scanning page.

Solution This operation is within the current Engineering Specifications of bizhub 920.


DescriptionBlank white band 1" on front side of all copies and prints.

SolutionCAUSE: The dust proof glass on the write unit is pushed too far in preventing the laser to write the image completely on the front (user) side of the machine.

SOLUTION: Position the dust proof glass correctly on the write unit.


DescriptionCopying process continually cycles ON/OFF without ever feeding a sheet of paper after pressing the START key. Unable to output copies or internal testprints. No jam or error code is displayed.

SolutionCAUSE: Corrupted firmware.

SOLUTION: Flash the print control version to 11 and the image control version to 10. The problem may continue to be experienced if the machine is flashedwith print control version 12 and image control version 20.SPECIAL NOTE: Solution provided by David Cox, Komax Business Systems & Timothy Kemme, Pacific Office Automation / Salem.


Description

105


bizhub PRO 920

"Input Copy time" message at power up.

SolutionCAUSE: The Weekly time has been turned ON by mistake.

SOLUTION: Turn the weekly timer OFF. To turn the weekly timer OFF, perform the following;1. Press [Utility/Counter].2. Select [Administrator].3. Select [System Settings].4. Select [Weekly timer settings].5. Select [Weekly Timer ON/OFF setting].6. Highlight [Weekly timer OFF] and return to the main screen.


DescriptionRC501 replacement parts.

SolutionRefer to the [[RC501 Parts Catalog| RUN v:\PDFfiles\AcroRd32.exe V:\PDFfiles\internal_link016.pdf]] and [[920 Mount Kit| RUN v:\PDFfiles\AcroRd32.exeV:\PDFfiles\internal_link017.pdf]] for more detail.


Description Part number for the stapler adjustment jig.

Solution Stapler Jig(p/n 13QEJG010).


DescriptionError while removing TWAIN driver from eCopy™ ScanStation.

Solution CAUSE:The eCopy™ license has locked the TWAIN driver and has not released it. SOLUTION: The two eCopy™ services must be stopped in order to remove the TWAIN driver. Once the services have stopped, press the Retry button andthe removal process should continue. Once the TWAIN driver has been removed, restart the two services that were previously stopped.


DescriptionCode 23-50 after replacing the toner collection bottle on a RC501.

Solution CAUSE: There is a counter that must be reset when the bottle is full. SOLUTION: Reset the counter in the Technical Mode, Parts Life Counter, Preset Parts Life Counter, number 117.


DescriptionCannot receive CS Remote Care host E-mail or perform CS Remote Care communication test via Sendmail\Cyrus or equivalent E-mail server environment.ISPs will be using these SMTP and POP3 mail servers on UNIX or LINUX platforms.

Solution CAUSE: The bizhub PRO 1050/IC-611 and bizhub PRO 920/IC-203 will not complete the three POP3 requests when retrieving the E-mail attachment sentfrom CS Remote Care host system or an E-mail communication test. SOLUTION: Perform the following: 1. Verify the engine SMTP and POP3 account settings are correct by performing a test using the same settings from an E-mail client. 2. Download the IC-611 firmware and version 30-SBK0 (1050 p130sbk0p.exe), IC-203 firmware version 30-SBK0 (ic203 p120sbk0p.exe), and respectivemodification notices, whichare available via the Konica Minolta Download Selector. Note : The latest version firmware and system software is available via the Konica Minolta Download Selector. Access the Selector from SSD Web Support(CS Expert Support) by clicking on 'Download MSDS, Drivers, Firmware and more'.

106


bizhub PRO 920


DescriptionHow to determine what version of Sun Java™ is installed on a Microsoft® Windows workstation.

Solution To determine what version of Sun Java™ is installed, perform the following: 1. From a command prompt type:java -version 2. Press Enter. 3. The version of Sun Java™ will be indicated. If the command is not recognized then Sun Java™ is not installed.


DescriptionHow to set the user box data to auto delete the HDD data at a specific time interval.

SolutionPress Utility\Machine Manager Setting\Security Setting\HDD Manage Setting\Data Auto Delete and enter the time interval.


DescriptionThe first copies out in the morning are blank.

Solution CAUSE: Possible PC drum ground issue. SOLUTION: Clean the PC drum ground contacts.


DescriptionDue to the recent changes to the date that Daylight Saving Time begins, it may be necessary to adjust the time to allow the proper time to display on scansand faxes.

Solution Refer toattached Bulletin #5806 for the details. Note : To view a PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at: http://www.adobe.com/products/acrobat/readstep2.html


Description'Please load designated paper' message when using the RADF; all paper trays are loaded with the correct size paper.

Solution CAUSE: The NVRAM has failed. SOLUTION: Please call the SSD Hotline to obtain a replacement NVRAM.


DescriptionCan Account Track codes be imported and exported to the machine?

SolutionAccount Track codes can be imported to and exported from the machine. The main body NIC must be used for this function.


DescriptionWhen a RX/TX CS Remote Care E-mail Communication Test is performed, if the test is unsuccessful due to incorrect POP3 settings, the screen hangs ordisplays the status message"Now Communicating", without ever returning an error code. Additionally, no error code is printed out in the Communication log.

107


bizhub PRO 920

Solution CAUSE: Firmware upgrade required. SOLUTION:Special Printer Controller firmware for the bizhub PRO 1050 (30-COKO) and bizhub PRO 920 (20-COKO) has been released to address thisissue. After applying this special firmware, when a CSRC Communication Test fails, related to incorrect POP3 settings, the error "Communication Error code00-05" will display on the screen and a "Reception Failed" entry (mode 8000, result 0005) will now be listed in the Communication log. Notes : 1.This special firmware is available via the Konica Minolta Download Selector. Access the Selector from SSD Web Support (CS Expert Support) by clickingon 'Download MSDS, Drivers, Firmware and more'. Search underthe Product Groupfor 'BlackWhite Products' => 'bizhub PRO 1050'or 'bizhub920'=>'Firmware' selection, as well as'Solutions'=> 'CS Remote Care' =>'Firmware' selection. 2.If the Communication Test is successful, a "Completed" status is then displayed on the screen. When the Communication log is printed from Tech RepMode=> List Output, the successful communication is listed in the log.


DescriptionJ32-02or J32-04 when using the ADU.

Solution CAUSE: The second feed registration roller is worn. SOLUTION: Replace the second feed registration roller (p/n 55VA 4603 0) and the bushings (p/n 55VA 7602 0).


DescriptionSC32-03.

Solution CAUSE: Contact failure of connectors (CN87/CN228/CN420). SOLUTION: Checkfor proper connectionof CN87/CN228/CN420.


DescriptionWhen reloading a paper tray the START key must be pressed. Is there an auto-start feature or option available?

Solution Firmware version I40/C14 introduceda new auto restart feature that will restart the copy or print jobautomatically when reloadingthe paper tray.SettingSoftswitch 11-6 to1 will enable this feature. Perform the following procedure: 1. Press the Utility key and then Stop, 0, 0, Stop, 0, 1. 2. Press System Input. 3. Press Software Switch Setting. 4. Advance to softswitch 11-6 and make it1. Note : The latest version firmware or system software is available via the Konica Minolta Download Selector. Access the Selector from SSD Web Support(CS Expert Support) by clicking on 'Download MSDS, Drivers, Firmware and more'.


DescriptionKonica Minolta MicroPress® System Software Installation Checklist.

Solution PROCEDURES TO FOLLOW: 1. Please check all firmware levels are up to date according toattached Konica Minolta MicroPress® Checklist. 2. This information applies for MicroPress® versions 7.0.1.1 and 7.5.0.0 (see attached EFI bulletin). 3. Do not install any other firmware versions on the MFPs other than the ones mentioned in the document. 4. Do not install any patches other than the ones mentioned in the attached document. 5. Attached Bulletin07-GB-018 specifies new functionalities and/or features available with MicroPress® version 7.5.0.0. 6. Any new firmware or patches for the engines or controllers (MicroPress®-related) will be updated in the Konica Minolta Firmware Listaccessibleat SSDWeb Support (CS Expert Support) by clicking on 'Latest Firmware Levels'in the left-hand "menu" ofeach technician'sHome Page. Note : To view a PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at: http://www.adobe.com/products/acrobat/readstep2.html

108


bizhub PRO 920


DescriptionScan to SMB support for Macintosh® 10.3.x and 10.4.x.

Solution System code isavailable for the IC-203 (version 20-CON0) and the IC-611 (version 30-CON0)which provides support for Scan to SMB to Macintosh® 10.3.xand 10.4.x. System code is available via the Konica Minolta Download Selector. Access the Selector from SSD Web Support (CS Expert Support) by clicking on'Download MSDS, Drivers, Firmware and more': 1. Login in via www.mykonicaminolta.com 2. Select the "Service" link located on the top of the page.3. Select the "SSD (DNA, Drivers, MSDS)" link located on the left.4. Select the "SSD Home Page" link located in the middle of the page.5. Select the "Download MSDS,Drivers,Firmware and more" link located on the left. 6. Select "Black White Products" under the Product Group. 7. Select "IC-203" or "IC-611"for Product. 8.Select "System Code" for File Type. Note : Please refer to the attached Release Notes for additional information. To view a PDF, Adobe Reader® must be installed. Adobe Reader® can bedownloaded for free from the Adobe® web site at: http://www.adobe.com/products/acrobat/readstep2.html


DescriptionHow to print to a printer on a Microsoft® Windows XP PC from a Macintosh® running OS version 10.4.x.

Solution Please perfrom the step-by-step procedure mentioned in the attached document. Note : To view a PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at: http://www.adobe.com/products/acrobat/readstep2.html


DescriptionHow to output a printer job that exceeds the finisher staple capacity limit.

Solution When outputting a printer job with staple mode, the machine cancels the staple mode and stops indicating topress the START key tocontinue printingat thepoint the staple capacity is exceeded. To continue the operation, the user needs to press the START key. CAUTION : The FS-604 exits the pages before the capacity limitis exceeded without stapling. On the other hand, the FS-509 and FS-516 exit the sheetsbefore the capacity limit is exceeded with stapling. How to output continuously: Set the software dipswitches as follows. This settingenables batch data reading. At the point data reading operation completed, if the number of pages of thejob exceeds the staple capacity, the staple mode is canceled and all pages are output without being interrupted.Dipswitch settings:Dipswitch 21-0=1Dipswitch 29-2=0 (bizhub PRO 920) Dipswitch 14-3=1 (bizhub PRO 1050/1050P/1050e/1050eP with FS-503). Image control program must be version 50-COM0 or later. Note : The latest version firmware or system software is available via the Konica Minolta Download Selector. Access the Selector from SSD Web Support(CS Expert Support) by clicking on 'Download MSDS, Drivers, Firmware and more'. CAUTIONS : 1. The output of the 1st set of jobs slows down as output operation starts after all pages are read. 2. Staple mode is canceled when mixed original mode is selected (including mixture of the same series sizes). SPECIAL NOTE : Solution contribution by KMBT (Japan).


Description920 User Manuals.

SolutionDrivers, Manuals, and MSDS information is available on the [[http://www.kmbs.konicaminolta.us| URL http://www.kmbs.konicaminolta.us/]] website.


Description

109


bizhub PRO 920

How to install a Windows 2000 or XP driver on an NT4 server.

NOTE: These procedures will not work with all Konica Minolta print drivers as the development of the NT driver may not have been done at the same time asthe 2000/XP drivers. The driver name MUST match between OS versions or this procedure will not function. Most of the newer drivers used common namesbetween the different OS versions and should work using these procedures.

SolutionNot all 3rd party OEM Windows 2000/XP print drivers can be installed on an NT4 server, but these are the procedures to install the driver if it is compatiblewith this installation method..

Section 1: Installing a Windows 2000 or Windows XP Printer DriverTo install a Windows 2000 or Windows XP printer driver on a Windows NT server, follow these steps from a Windows 2000- or a Windows XP-basedcomputer on your network:

Note: If you are using either a Windows NT 4.0 driver or a Windows 2000 driver that is supplied by a third party, these steps may not work due to differencesin design or driver names.

You may also receive error messages when you are managing drivers on a Windows NT 4.0-based printer server from a Windows 2000- or a WindowsXP-based computer. For additional information, the symptoms section of this solution should be applied.

1. Click Start, click Run, and then type the Uniform Naming Convention (UNC) path for the Windows NT 4.0 print server (for example: \\Nt4srvname).

This action displays the shares on the remote computer. 2. Open the Printers folder. This action takes you into the printers folder on the remote computer. 3. Right-click the icon for the printer for which you want to add the Windows 2000 driver, and then click Sharing. 4. From the Sharing tab, click Additional Drivers, click the Intel/Windows 2000 option, and then click OK.

SYMPTOMS (If an error occurs when trying to manage the printer from Windows 2000 or XP)

If you try to manage a Microsoft Windows NT 4.0-based printer server from a Windows 2000-based computer to install an OEM version 3 driver, you mayreceive the following error message: The printer driver you selected is either not compatible with your current version of Windows, or it may not be available. Select a compatible driver from thelist, or contact your administrator for help.

WORKAROUNDTo work around this behavior, place the version 3 printer driver's .inf file in the %SystemRoot%\Inf folder on the Windows 2000-based computer. After you dothis, you are prompted to provide a path to the driver installation files instead of receiving the error message.


DescriptionHow to perform the Touch Panel sensitivity adjustment.

SolutionTo adjust the touchscreen sensitivity, perform the following:1. Press Utility/Mode on the operation panel.2. Press Touch Panel Adjust on the LCD.3. Touch the + at the upper right corner of the touchscreen lightly with a touch pen (something with a round tip which is made of resin is recommended as atouch pen). Check the coordinates displayed in the top line at the top of the touchscreen.4. Ensure the X coordinate and the Y coordinate displayed in the message area fall within the standard values. The acceptable values are on the secondline.5. If the values are not within the acceptable parameters, repeat Step 4 until the values are acceptable.6. Touch the + at the lower left corner of the touchscreen lightly with a touch pen (something with a round tip which is made of resin is recommended as atouch pen). Repeat the process used for the upper right coordinate until acceptable values are achieved.7. As verification of a correct adjustment, touch the [CHECK] icon at the upper left and lower right corners. You should hear a beep tone for each one. If abeep tone is not heard, repeat the adjustment.9. Press 1 on the keypad to exit the adjustment mode.10. Press Close to exit Utility Mode.


DescriptionHow to set for full scan (no edge deletion).

SolutionTo set for full scan, perform the following:1. From the normal screen, touch the Application Icon2. On the next screen, touch the Image Adjustment icon3. On the next screen, touch the Full Scan icon4. Touch OK to accept.

110


bizhub PRO 920


DescriptionJS203, to improve the accuracy of Paper full detection, the shape of the Guide has been changed.




DescriptionLoose screw of reverse unit fulcrum section.

SolutionRefer to bulletin 5138 details.Note: To view the above PDFs, Acrobat* Reader must be installed. Acrobat Reader can be downloaded for free from the Adobe* Web site at:[[http://www.adobe.com/products/acrobat/readstep2.html| URL http://www.adobe.com/products/acrobat/readstep2.html]]



DescriptionHow to staple in the upper left corner of 8.5X11R and 14 inch paper

SolutionTo accomplish this perform the following:

1. From the basic screen, touch finishing and then select corner and touch OK.2. From the basic screen, touch Combine Originals.3. On the next screen, touch Original Direction.4. On the next screen, touch Left then OK.


DescriptionAssembly failure of APS sensor.

SolutionRefer to bulletin 5177 details.Note: To view the above PDFs, Acrobat* Reader must be installed. Acrobat Reader can be downloaded for free from the Adobe* Web site at:[[http://www.adobe.com/products/acrobat/readstep2.html| URL http://www.adobe.com/products/acrobat/readstep2.html]]



DescriptionHow to make copies of a 11x17 open booklet and make a copy of the page closest to scale plate.

SolutionTo make copy of 11x17 size booklet and page closest to the scale plate:1. Press Utility2. Select #3 Admin Settings (enter password)3. Select #1 System Setting4. Touch Expert Adj5. Select # 2 Erase Adj then touch Non Image Area Erase, select Do Not Erase When X1.0Note: When placing a 11x17 booklet on the platen the RADF is not being used so Non Image Erase feature is not being used.SOLUTION PROVIDE BY Doug Bivens - Quality Business Systems.


111


bizhub PRO 920

DescriptionCountermeasure against pinching of motor cooling fan wiring.

SolutionSee TNBT0500237EN00.pdf and bizhub_920_mod_procedure.pdf for details.Note: To view the above PDF, Acrobat* Reader must be installed. Acrobat Reader can be downloaded for free from the Adobe* Web site at:[[http://www.adobe.com/products/acrobat/readstep2.html| URL http://www.adobe.com/products/acrobat/readstep2.html]]



DescriptionUnable to remove the drum coupling from the drum shaft.

SolutionSee TNBT0500241EN00.pdf , TNBT0500241EN00_NewProcedure.pdf and TNBT0500241EN00_ResultOfAnalysis.pdf for details.Note: To view the above PDF, Acrobat* Reader must be installed. Acrobat Reader can be downloaded for free from the Adobe* Web site at:[[http://www.adobe.com/products/acrobat/readstep2.html| URL http://www.adobe.com/products/acrobat/readstep2.html]]



DescriptionDamage of coating of registration wiring of ADU.

SolutionSee TNBT0500238EN03.pdf and TNBT0500238.pdf for details.Note: To view the above PDF, Acrobat* Reader must be installed. Acrobat Reader can be downloaded for free from the Adobe* Web site at:[[http://www.adobe.com/products/acrobat/readstep2.html| URL http://www.adobe.com/products/acrobat/readstep2.html]]



DescriptionHow to setup SMB onetouch entries via the web interface

SolutionBrowse to the engine nic, not the IC-205 nic.Go to Machine Manager Setting, enter user name and password for the Admin account, Select Scan Transmission Setting, scroll down to SMB Registration,fill out the information and then select the Registration button. To view all the one touches that are listed to the mainbody, select the "Only List" button underSMB Registrations.


DescriptionUnable to PING the NIC after setting a TCP/IP* address on it.

SolutionCAUSE: The main power switch must be turned OFF/ON to set the NIC address.

SOLUTION: Turn the main power switch OFF/ON to set the NIC address.



DescriptionFS602/ZU602, the punch selections are not available when copying but function when printing.

SolutionCAUSE: The Punch unit has not been enabled or is isolated due to an internal service error.

SOLUTION: Perform the following:1. Check to see if DIPSW26, bit 3 is set to ON, and DIPSW26, bit 2 is set to OFF in the [25] service mode. These DIPSW settings is for enabling the (ZU602)

112


bizhub PRO 920

PK505 when installed.2. Recommend checking DIPSW19, bit 5 in the [25] service mode. The DIPSW setting is for faulty parts isolation of the PK505 (ZU602) and should be set toOFF. If set to ON, the punch had some type of error during set up. Set bit to OFF to reset isolation condition.3. If the issue continues, the PKCB (Punch Unit Control Board) should be replaced.


DescriptionFS509, trail edge flipping of stapled set.

SolutionSee DLBT0600205EN00.pdf for details.Notes:1. The latest version system software, firmware, and print drivers are available on the Konica Minolta FTP site .2. To view the above PDF, Acrobat* Reader must be installed. Acrobat Reader can be downloaded for free from the Adobe* Web site at:[[http://www.adobe.com/products/acrobat/readstep2.html| URL http://www.adobe.com/products/acrobat/readstep2.html]]



DescriptionIs the bizhub 920 supported for the Counter Reader function in PageScope Net Care 5.23.024?

SolutionPageScope Net Care 5.23.024 supports the Counter Reader Function for the bizhub 920 with plug-ins installed.Note: When a model is listed as supported for Net Care, it does not necessarily mean that it is supported for Counter Reader unless specifically stated.


DescriptionCan the AS/400* print to the bizhub 920?

SolutionThe bizhub 920 with the IC202, produced acceptable output when receiving jobs from the AS/400 via the LinkCom III. Both IPDS and SCS print jobsproduced output that was correct and acceptable.



DescriptionIn BOX mode, for copy reprint and storage, RECALL is grayed out. Also grayed are Scan to HDD and Scan to PC under STORE. HDD1 (main body) isinstalled.

SolutionCAUSE: Dipswitch 18-7 is set to 1 isolating HDD1

SOLUTION: In tech rep mode (utility, stop, 00, 01) set dipswitch 18-7 to 0 (normal) under the System menu.


DescriptionRelease of Version 20 Firmware (Major Function Upgrade).

SolutionSee Bulletin Number 5262 for details.Note: To view the PDF, Acrobat* Reader must be installed. Acrobat Reader can be downloaded for free from the Adobe* Web site at:[[http://www.adobe.com/products/acrobat/readstep2.html| URL http://www.adobe.com/products/acrobat/readstep2.html]]



DescriptionCan the bizhub 920 operation panel reset time be changed to reset in 30 seconds?

113


bizhub PRO 920

SolutionThe fastest setting for the reset time on the operation panel of the bizhub 920 is 60 seconds.


DescriptionHow to input the network path when setting up IPP for Microsoft* Windows 9x, ME, 2000, XP or 2003.

SolutionTo input the network path for IPP, perform the following:1. Click Start, choose Settings, and then choose Printers.2. In the Printers window, double-click the icon for the print driver.3. Choose Properties from the File menu.4. Click the Details tab, and then click Add Port. The Add Port dialog box will appear.5. Enter the network path for the printer as follows: http://IP address or DNS name:631/ipp.6. Click OK.Note: IPP printing across a router requires port numbers 631 and 80 to be unblocked.



DescriptionEquitrac* is not counting pages when printing test pages from the Local server. The reports Manager lists no jobs for the IC611 Visual PostScript* driver.Under messages, the fail error can be observed:The page counting engine failed for job by user . Context: 'Win2kPortInfo::end_job'. Error: [Page counter failure].

SolutionCAUSE: Output setting should be changed.

SOLUTION: Change Output setting from Optimize for Speed to Optimize for Portability. Note: If the Microsoft* Window 2000 or 2003 printer driver is being used, change setting under 'Printing Defaults' on the server.



DescriptionThe bizhub PRO Firmware Function Enhancements (2-27-2006).

SolutionSee Bulletin 05-GB-123 .Note: To view the PDF, Acrobat* Reader must be installed. Acrobat Reader can be downloaded for free from the Adobe* Web site at:[[http://www.adobe.com/products/acrobat/readstep2.html| URL http://www.adobe.com/products/acrobat/readstep2.html]]



DescriptionDATA FORMAT NOT SUPPORTED message when printing using a PostScript* driver.

SolutionCAUSE: The PostScript option (PS503) is not installed.

SOLUTION: Install the PostScript option (Item #15RL).



DescriptionIs the bizhub 920 supported with OneRip2?

SolutionThe bizhub 920 is supported with OneRip2 version 2.03 and later.

114


bizhub PRO 920


DescriptionWhen trying to connect to the internal print server on the bizhub 920 with AHT OneRip2, a communication error is indicated.

SolutionCAUSE: SNMP not enabled.

SOLUTION: SNMP must be enabled on the bizhub 920.


DescriptionIf the bizhub PRO 920 is in operation, how many subsequent jobs can be programmed ahead to copy or print?

SolutionNinety-nine (99) jobs can be programmed during operation.


DescriptionThe tri-folding functions are grayed out in the PostScript* (V) driver version 2.0.0.1 on Microsoft* Windows 2000 systems.

SolutionCAUSE: The tri-fold function problem has been identified as a driver issue.

SOLUTION: Install the lastest PostScript (V) driver version 2.1.0.0. Printer drivers can be found in the "Library" section of MyKonicaMinolta.com. Userswithout MyKonicaMinolta.com access can download drivers from the public web site: [[http://kmbs.konicaminolta.us/eprise/main/KMBS/Support_Center/Home| URL http://kmbs.konicaminolta.us/eprise/main/KMBS/Support_Center/Home]]



DescriptionUnable to login through PageScope Web Connection. User is prompted for a user name and password.

SolutionCAUSE: This indicates that Authentication is enabled.

SOLUTION: Either provide valid username and password (Active Directory, SMB, NDS or MFP Authentication) or turn Authentication OFF.


DescriptionSC23.-02 when making copies.

SolutionCAUSE: A failed M3 developer drive motor.

SOLUTION: Replace M3 developer drive motor (p/n 65AA-80021).


DescriptionHow to delete a registered user when SMB scanning.

SolutionTo delete a registered SMB user, perform the following:1. Press the Utility and select Administrator.2. Enter the password 12345678.3. Press #8 Scanner Destination Storage.4. Press #1 Destination Address Change/Delete.5. Select SMB.6. Select the user to be deleted and select Delete.

115


bizhub PRO 920


DescriptionHow to delete a registered user when E-mail scanning.

SolutionTo delete a registered E-mail user, perform the following:1. Press the Utility and select Administrator.2. Enter the password 12345678.3. Press #8 Scanner Destination Storage.4. Press #1 Destination Address Change/Delete.5. Select E-mail.6. Select the user to be deleted and select Delete.


DescriptionThe bizhub 920 requires what version of Image Control Firmware to support printing from MicroPress* 7?

SolutionTo support Printing from MicroPress 7, version 20-ABSO must be installed on the bizhub 920.



DescriptionIs the bizhub 920 supported with MicroPress* 7?

SolutionThe bizhub 920 is supported in MicroPress 7.0.0.6 and later.



DescriptionHow to enable Continuation of Print.

SolutionTo enable Continuation of Print, perform the following:1. Press the Utility/Counter key.2. Press Administrator Setting and enter the password.3. Press Copier/Printer Setting.4. Press Continuation of Print and press the ON icon.5. Press Exit to resume operations.


DescriptionRecommended transparency, bizhub 920

SolutionStandard transparency (PCUA 946427 - equivalent to the 3M* type PP2500 688/503).The following are alternate high temperature transparencies that are also recommended:3M type PP29503M type CG5000Note: Konica Minolta recommends feeding transparencies through the bypass tray to reduce the occurrence of misfeeding.



DescriptionDoes the ZU602 support Z-folding with 8.5x 14 paper?

116


bizhub PRO 920

SolutionZ-fold functions only as a double fold when using 8.5x14 paper. Refer to the 920 Bizhub Copier User Reference Guide, section 12, page 21 or page 341 of402 in the PDF.


DescriptionHow to write a custom script in order to accomplish printing tasks.

SolutionUse the Scripting Option (if purchased) to open an existing predefined script and select to Edit the existing script. Write a Microsoft* Visual Basic Script thensave the script. This script can be used in the AutoScript feature and be run automatically.



DescriptionCan a particular screen (Scan mode, Fax mode) be set as the default screen?

SolutionPresently there is no way to change the default screen from the Copy mode. Future firmware releases may contain this option.


DescriptionHow to set any paper tray as the default paper tray.

SolutionPerform the following procedure to set any paper tray as the default paper tray:1. Press the Utility key and select Copier Setting.2. Press Reset Setting and select Factory.3. From the main copy screen select the desired paper tray for the default and press OK.4. Press the Utility key and select Copier Setting.5. Press Reset Setting and select Current.6. Press OK and then select Rest Function Setting.7. Press Auto Reset Key Setting and select Initial.8. Press Close 4 times to return to the main copy screen.


DescriptionThe LDAP function is grayed out with version 12 firmware installed.

SolutionUpgrading to version 20 firmware or above enables the LDAP function on the 920bizhub.


DescriptionTab job stored on the HDD no longer prints properly after upgraded to version 20 firmware and version 12 system code. One tab is printed and the remainderare ejected.

SolutionThis problem can be corrected by going into the "Utility Mode" then select the "Function" setting. From the next display select" Each function setting". From the next screen Select "Needless Tab paper exit". Change the setting to "off". Exit from the menu.


DescriptionNEW - MicroPress 7.0 Support for bizhub PRO 920

SolutionRefer to Bulletin #5358 for details.

117


bizhub PRO 920

Note: To view the above PDF(s), Acrobat* Reader must be installed. Acrobat Reader can be downloaded for free from the Adobe* Web site at:[[http://www.adobe.com/products/acrobat/readstep2.html| URL http://www.adobe.com/products/acrobat/readstep2.html]] * Trademark ownership information


DescriptionPI501, are custom sizes available with the Post Inserter?

SolutionCustom sizes are not available on the PI501.


DescriptionThe bizhub serial number locations.

Solution The bizhub serial number locations .Note: To view the PDF, Acrobat* Reader must be installed. Acrobat Reader can be downloaded for free from the Adobe* Web site at:[[http://www.adobe.com/products/acrobat/readstep2.html| URL http://www.adobe.com/products/acrobat/readstep2.html]]



DescriptionIs there a Job Reserve setting for scanning.

SolutionIn order to use Job Reserve for scanning, press Job Reserve (only displayed when scanning) on the touchscreen during the scan. This will allow theoperator to scan jobs right after each other.


DescriptionHow to set the bizhub 920 total counter so that 11x17 paper counts as one count and not two counts.

SolutionTo set the bizhub 920 total counter so that 11x17 paper counts as one count and not two counts, enter the tech rep mode, select system input, then selectsoft switch settings (DipSW. 4-7 = 0).


DescriptionWhat is the maximum thickness of paper allowed for use with the bizhub 920?

SolutionThe bizhub 920 Service Manual, page 4, under " Type of paper" states the maximum paper thickness supported is 200gsm.


DescriptionNew FS516 finisher replaces FS509 for the bizhub PRO 920.

SolutionRefer to Bulletin #06-GB-028.pdf for details.Note: To view the above PDF(s), Acrobat* Reader must be installed. Acrobat Reader can be downloaded for free from the Adobe* Web site at:[[http://www.adobe.com/products/acrobat/readstep2.html| URL http://www.adobe.com/products/acrobat/readstep2.html]] * Trademark ownership information

118


bizhub PRO 920


DescriptionHow to perform scanning with a Hecon device installed, but not inputting the key or pass code?

SolutionThis issue has been correct with firmware version Printer Control 13 and Image 30. After updating the firmware ensure DIP SW 12-1 is set to a 0


DescriptionIn Microsoft* Publisher 2002/2003, publications/records are not individually collated and stapled when duplexing and using the mail merge feature ofPublisher.

SolutionCAUSE: Registry edit required.WARNING: Incorrectly editing the registry may severely damage the system. Before making changes to the registry, back up any valued data on thecomputer. Konica Minolta is not responsible for any system errors that may result from using a registry editor incorrectly.

SOLUTION: Microsoft Publisher can be enabled to individually collate, staple and duplex publications/records when using the mail merge feature of Publisherthrough a registry edit. This can be done either manually or by a script.To manually edit the registry, open the Registry Editor by clicking Start, click Run, type regedit, and then click OK. Go to:1. HKEY_CURRENT_USER\Software\Microsoft\Office\ \Publisher\Printing.2. Right-click on the Printing folder, select New= String Value.2. Create new "string value" called: NumberOfRecordsPerBatch.3. Double-click and set the Value Data to 1. Instead of grouping records together into groups of 10 (Publisher default) to send to the printer, the records arenow sent in groups of 1 (i.e., each document is sent separately).Note: A value for this size setting can be set between 0 and 99999.

To update the registry 'automatically' from a script:1. Download the script from [[http://ed.mvps.org| URL http://ed.mvps.org/20031Rec.reg]].2. Save the REG file to the Desktop.3. Double-click on the icon, and then click on Yes to the question, 'Are you sure you want to add the information in C:DOCUME~1\administrator account\Desktop\20031Rec.reg to the registry?'4. The new value will be added to the registry.Notes: a. Refer to [[Windows registry tips and guidelines|URL http://techweb.konicabt.com/tpm/media/registry_guide.pdf]] for additional information. b. To view the above PDF, Acrobat* Reader must be installed. Acrobat Reader can be downloaded for free from the Adobe* Web site at:[[http://www.adobe.com/products/acrobat/readstep2.html| URL http://www.adobe.com/products/acrobat/readstep2.html]]



DescriptionHow is the punch unit disabled on the 920 bizhub?

SolutionSet Soft Sw. 19-5 = 1 to disable the punch unit.


DescriptionIs PageScope Direct Print supported in the Mac environment?

SolutionAll the PageScope Products are Windows based products with no support for MAC's.


DescriptionHow to retrieve scanned images from the 920/IC203 hard drive using the FTP protocol.

SolutionThe recommended method to retrieve TIFF (only) scans from the 920/IC203 is to use TWAIN driver 2.04 which can be downloaded from Konica's [[FTP site|URL ftp://kbtdigital:[email protected]]]

119


bizhub PRO 920

[[ScanTrip version 1.73| URL http://www.sec.konicabt.com/version2/product.html?p=31492]] will not operate correctly with the 920 at this time. ScanTrip 2.0is being developed to interface with the 920 and should be available soon. This will be a free update to ScanTrip 1.73.

To retrieve scans from a browser:

ftp://BOX:box#@IP address i.e. ftp://BOX:[email protected]

This will bring up a log on Window, the User Name should be filled in as ‘BOX’ Then tab to the Password field and enter the following:

[box#]:[password] i.e. 4702:1234

When the above is entered you will be able to view/retrieve the document(s).

To retrieve scans from a Command (DOS) prompt:

Start an ftp session

The User: is ‘BOX’The Password: is [box#]:[password]


DescriptionMail Merge staples all pages together, but end user would like to separate mail merge into separate jobs based by name or address.

SolutionDownload and import [[word_mail_merge_printing|URL http://techweb.konicabt.com/tpm/media/word_mail_merge_printing.pdf]] into normal.dot. Set up thedriver you want to use as the default and then set the finishing features desired in Printing Preferences. Run normal.dot under macros, you should bepresented with a question of how many sections are in the merge (i.e., how many pages before the next name or address in the merge).


Description Part number for the punch unit board (PDB).

Solution Punch unit board (p/n 15KA-9010).


DescriptionHow to determine the origin of scanning issues in eCopy™.

Solution To help determine the origin of scanning problems, eCopy™ ShareScan OP ships with a simple TWAIN scanning application called Twack32 (TwainToolKit).It is used to determine whether or not a scanning problem is specific to the scanning device or a problem with the eCopy™ software. To use Twack32: 1.Go to Target dir\ecopy\ScanStation Client\Bin\Twack_32.exe. 2. Go to File/Select Source and select the TWAIN driverbeing used(eCopy™ ShareScan OP must be closed). 3. Go to File/Acquire. The TWAIN interface should display. 4. Click on the Scan button. The image will preview on the screen.


DescriptionWhy does the Send to eCopy™ tab not appear in the Manage section?

Solution The Send to eCopy™ tab does not appear for two reasons: 1. Using a simulator version of the eCopy™ software. 2.Wrong NFR key was obtained. The Scanner NFR key takes control of the optics of the MFP and does realtime scanning.The Send to eCopy™ key allows the scanner function to work asstated above but also provides the option of monitoring a hotfolder.The send to eCopy™ does not allow both options to function. TheTWAIN drivercan beused to either scan or Send to eCopy™ to monitor a folder.

120


bizhub PRO 920


DescriptionWhen setting up authentication, accounts cannot be added.

Solution CAUSE: Account distribution is set to 1000. SOLUTION: To change account distribution setting, perform the following: 1.Touch Utility key, then Machine Manager Setting. 2.Touch User Authentication/Account Track. 3.Touch User Authentication Setting. 4.Touch the down-arrow and change Account Distribution Number to 1.


DescriptionNo power; operation panel is blank; Energy Saver light is ON.

Solution CAUSE: HDD has failed. SOLUTION Replace the HDD (p/n 57GA-7410).


DescriptionHow to set up Scan to SMB for a Microsoft® Windows Vista™ workstation.

Solution Please perform the step-by-step procedures for the specified modelasoutlined in the attached documents. Note : To view a PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at: http://www.adobe.com/products/acrobat/readstep2.html


DescriptionWhat are the limitations of using the Post Inserter Tray with MicroPress®?

Solution 1. Multiple consecutive pages from the Post Inserter are not allowed.2. Post Insert pages cannot start or end a job. If this is required then the Front and/or Back Cover finishing option should be employed.3. Post Insert pages cannot start or end a subset. Note : This issue has been fixed with MicroPress® 7.0.1.1 and later with the bizhub PRO 1050. This is currently still a limitation with the bizhub PRO 920.


DescriptionAre Konica Minolta MFPs compatible with Category 6 cable standard?

Solution Konica Minolta MFPs are fully compatible with Category 6 cable standard. Category 6 cable is a cable standard for Gigabit Ethernet and other network protocols that is backward compatible with the Category 5/5e and Category 3cable standards. Cat-6 features more stringent specifications for crosstalk and system noise. The cable standard is suitable for 10BASE-T/100BASE-TX and 1000BASE-T(Gigabit Ethernet) connections and it provides performance of up to 250MHz.


Description Touchscreen locked up.

Solution CAUSE: The touchscreen adjustmentwas performed incorrectly. SOLUTION: Perform the touchscreen adjustment. To adjust the touchscreen, perform the following:

121


bizhub PRO 920

1. Select the Utility/Counter screen. 2. Press number 5 on the key pad to enter the touchscreen adjustment. 3. Press the upper right (*) with a pencil tip. 4. Press the lower left (*) with a pencil tip. 5. Press the lower right [Check Box] with a pencil tip. 6. Press the upper left [Check Box] with a pencil tip. 7. Power the machine OFF/ON and test.


Description Part number for the PS305 (Sensor board) assembly.

Solution PS305(p/n 13NK-9611).


Description FS604, 'Mishandled Paper' message.

Solution CAUSE: A small piece of paper is jammed in the saddle stitch unit. SOLUTION: Inspect and remove any paper found in the saddle stitch unit.


Description Intermittent 'Reload 1 original in the DF' messageafter the last sheet feeds through the machine document feeder. When the original re-feeds the documentis notprinted.

Solution CAUSE: Dirty document feeder sensors. SOLUTION: To clean the sensors, perform the following: 1. Power OFF the machine; inspect and clean all DF sensors. 2. PowerON the machine and enter the Tech Rep mode. 3. Select Machine adjustments, ADF adjustment, and ADF sensor sensitivity adjustment. 4. Perform the sensor sensitivity adjustment.


Description PULL OUT FINISHER STACKER AND CHECK STAPLER message when selecting staple mode.

Solution CAUSE: The staple cartridge is not fully seated. SOLUTION: Ensure the staple cartridge is fully seated.


Description How toPING a Macintosh*.

Solution To PING a Macintosh, perform the following: 1. Double-click the Finder. 2. Select Applications. 3. Select Utilities. 4. Select Terminal. 5. From the Terminal window type the standard PING command. * Trademark ownership information

122


bizhub PRO 920


Description How to enable/disable ADF Frame Erase.

Solution To enable/disable ADF Frame Erase, perform the following: 1. Press the Utility/Counter key. 2. Touch [6 Administration Setting] on the touchscreen. 3. Touch [1 System Setting] on the touchscreen. 4. Touch [6 Expert Adjustment] on the touchscreen. 5. Touch [ADF Frame Erase Setting] on the touchscreen. 6. U nder Job Setting on the touchscreen, touch [On] for enable or [OFF] for disable. 7. Touch [Close] on the touchscreen. 8. Touch [Exit] on the touchscreen.


Description How to adjust the ADF Frame Erase setting.

Solution To adjust the ADF Frame Erase setting, perform the following: 1. Press the Utility/Counter key. 2. Touch [6 Administration Setting] on the touchscreen. 3. Touch [1 System Setting] on the touchscreen. 4. Touch [6 Expert Adjustment] on the touchscreen. 5. Use the numeric keypad to enter the desired ADF frame setting by pressing the numeric key, which corresponds to the desired ADF frame setting. TheADF frame erase can be programmed with a value of 1-5 mm. 6. Touch [Close] on the touchscreen. 7. Touch [Exit] on the touchscreen.


DescriptionJ21-02 shortly after power up.

SolutionCAUSE: Drum wrap jam; the Dmax sensor has detected a paper on the drum surface while in the idle state.

SOLUTION: Remove the drum unit from the machine and inspect the area in front of the Dmax sensor for a sheet of paper. Remove any paper found in thevicinity of the Dmax sensor. If, no paper is present in front of the Dmax sensor, the Dmax sensor should be cleaned.


DescriptionMultiple lines in the lead-to-trail direction when copying through the RADF only.

Solution CAUSE: Failed image CB. SOLUTION: Reseat all connectors on the image CB. Replace the image CB (p/n 57GA-9010) as necessary. SPECIAL NOTE : Solution provided by Thomas Cassimere, KMBS, Louisiana.


DescriptionA recalledjob on the HDDreferences tab paper and thecopier stops printing when attempting to pull tab paper from the bypass tray. Copier is asking for 8.5x11paper.

Solution CAUSE: Incorrectly programmedjob. SOLUTION: Reprogram the jobon the copier and set the paper type as plain. When the job is recalled, manually set the bypass for tab paper.

123


bizhub PRO 920


DescriptionJ31-02 error code when feeding tab paper from any paper tray.

Solution CAUSE: The tab extension width must be less than 12.5mm wide. Refer to page 4-10 of the bizhub Pro 920 User’s Guide. SOLUTION: Cut the tab down to the correct size. If the tab paper passes through the copier without a problem, advise the customer to purchase the correcttab paper to prevent future jamming issues.


DescriptionJ65-05 at power up.

Solution CAUSE: Reflective bracket for the PS309 is malformed resulting in a false reading. SOLUTION: Carefully re-form the reflective bracket.


DescriptionSC18-22.

Solution CAUSE: ICP8 on the PRCB is open. SOLUTION: Replace the PRCB (p/n 57GA-902 0).


DescriptionSC32-02.

Solution CAUSE: ICP9 on the ADU Driver Board is open. SOLUTION: Replace the ADU Driver Board (p/n 56GA-908 0).


DescriptionIs Active Directory supported with Authentication Enabled?

SolutionActive Directory is not supported on the bizhub PRO920/IC-203.


DescriptionSC42-17.

Solution CAUSE: ICP10 on the AC Drive Board is open. SOLUTION: Replace the AC Drive Board (p/n 56GA-908 0).


DescriptionJam code 72-29 when using the main tray of the FS-604.

Solution

124


bizhub PRO 920

CAUSE: Failed M7 and/or Sorter Control Board. SOLUTION: Replace M7 (p/n 56AA 8011 0) and the Sorter Control Board (p/n 15SJ-901 0) as a set.


DescriptionUnable to print. Can browse the NIC and print various reports.

Solution CAUSE: The PostScript driver is being used,yet the PostScript option is not installed. SOLUTION: Verify that the PostScript option is not installed by browsing to the NIC. The PostScript demo page will not be displayed. Load the PCL driver toallow printing.


Description'Please load designated paper in the paper tray' message,yet paper is loaded correctly.

Solution CAUSE: The paper type is set incorrectly. SOLUTION: To set the paper type, perform the following: 1. Press the Utility key. 2. Press Admin mode and enter password. 3. Press System Setting. 4. Press Paper Setting. 5. Press Tray Setting. 6. Press the paper tray in question. 7. Press Change. 8. Press Normal for the paper type.


DescriptionHow to check the image memory (DRAM) capacity.

Solution To check the image memory (DRAM) capacity, perform the following: 1. Enter the service mode. 2. Touch [Machine Status] on the touchscreen. 3. Touch [I/O Check] on the touchscreen. 4. Enter output code 97 using the numeric keypad. 5. Press the START key. 6. The amount of DIMM memory installed will be displayed on the touchscreen next to [OUT:]. 7. To return to the normal copy screen touch [Return] on the touchscreen. 8. Touch [Exit] on the touchscreen. 9. Touch [Exit] on the touchscreen.


DescriptionSC18-12.

Solution CAUSE: ICP10 On the Printer Control Board is open. SOLUTION: Replace the Printer Control Board (p/n 57GA-902 2).


DescriptionA gray haze is exhibited on copies after approximately 3500copies are made.

Solution CAUSE: A failed Drum Temperature Sensor.

125


bizhub PRO 920

SOLUTION: Replace the failed Drum Temperature Sensor (p/n 55GA-2090).


DescriptionHow to program mixed originals as the default setting.

Solution To program mixed originals as the default setting, perform the following: 1.Select Mixed Original.2.Press the Utility key and then press Copier.3.Press Reset Setting, Initial and OK.4.Press Reset Function Setting.5.Press Auto Reset Key Setting and select Initial.


DescriptionPart number for the Printer Control Board.

SolutionPrinter Control Board (p/n 57GA-9020).


DescriptionWhat is the difference between the Image Control Board and the Overall Control Board and what are the part numbers?

Solution There is no difference between the Image Control Board and the Overall Control Board except the terminology used from one Parts Catalog/Service Manualto the other. Image Control Board/Overall Control Board (p/n 57GA-9010).


DescriptionBackside of overlays are printing in the opposite direction.

Solution CAUSE: This is a product limitation. SOLUTION:Try using a search and replace function with a 3rd-party print server that supports search and replace functions. The string for a Linkcom™ IIImight look like the following: search replace 0x1b&l0Z0x0D0x1b&l0O0x0D 0x1b&l2O0x0d


DescriptionWhen performing multiple copy jobs, if a print job is sent, the job will print instead of waiting for the operator to finish.

Solution CAUSE: The print prohibit setting needs to be changed. This will enable more time for the operator to complete the task without being interrupted. SOLUTION: To change the print prohibit setting, perform the following: 1.Press the Utility key.2.Press Function Setting.3.Press Reset Function Setting.4.Select Print Prohibit.5.Select a higher number of seconds to prohibit a print job from printing during a brief moment of inactivity at the machine.


126


bizhub PRO 920

DescriptionWhen scanning to E-mail/HDD/FTP/SMB the selected address does not reset when auto-reset occurs or when pressing the auto-reset key.

Solution CAUSE: Early version firmware is installed or a softswitch is not set. SOLUTION: Install minimum firmware version 40 and set softswitch 21-7 to1. To set the softswitch perform the following: 1. Enter the Tech Rep Mode, (Utility, Stop 00, Stop 01). 2. Select System Input. 3. Select Softswitch Setting. 4. Scroll to softswitch 21-7 and make ita 1.


DescriptionSC46-16 during the copy process.

Solution CAUSE: Corrupt firmware, failed Overall Control Board or failed Printer Control Board. SOLUTION:Re-flash the machine firmware. If the problem persists,replace the Overall Control Board (p/n 57GA-9010) and/orthe Printer Control Board (p/n57GA-9020). Note : The latest version firmware and system software is available via the Konica Minolta Download Selector. Access the Selector from SSD Web Support(CS Expert Support) by clicking on 'Download MSDS, Drivers, Firmware and more'.


DescriptionIs Spanish firmware available?

Solution Spanish firmware is available. Please call the SSD Hotline to obtain the Spanish firmware. Note :The filename is 55GFI530ES00.


DescriptionFS-604, what is the part/item number for the staple cartridge?

SolutionStaple cartridge(Item #4448121).


DescriptionHowto duplex stored copy jobs recalled from the HDD/User Box; the jobs areprinting simplex.

Solution There are three ways to scan to hard drive/box and recall jobs; 1. Select the BOX icon on the operation panel to store and recall jobs which will duplex the recalled jobs properly. 2. Scan to HDD via the SCAN key. This option will not allow for duplexing. 3. Scan to HDD by selecting the BOX key. This option will not allow for duplexing.



Solution CAUSE: ICP9 on the Printer Control Board is open. SOLUTION: Replace the Printer Control Board (p/n 57GA 902 0).


127


bizhub PRO 920

DescriptionPart Number for the modified drum separating claw and modified toner guide brush assembly which are listed incompletely inBulletin #5584.

SolutionModifieddrum separating claw (p/n 57GA29190) andmodified toner guide brush assembly (p/n 57GAR72700).


DescriptionDoes PostScript printing come standard with the bizhub PRO 920?

Solution PostScript printing does not come standard with the bizhub PRO 920and is an option. To print using PostScript, please order an install the PS-503 kit (p/n15RL).


DescriptionLU--403, SC13-02 when feeding from Tray 5.

Solution CAUSE: The LU-403 CB and or the main motor have failed. SOLUTION: Replace the LU-403 CB and the main motor (M101) as a set. LU-403 CB (p/n 15SS-9010), and M101 main motor (p/n 57AA80080).


Description How to export/import the non-volatile data of parameter board.

Solution Exporting (for backup) and importing (for restoring) the parameter board data is possible using the Web Utilities. Trouble caused by non-volatile data abnormality like electrical noise can be minimized by data exporting. Importable data: All data except counter data can be imported.It is not possible to specify data items forimport. Note : To perform this, the machine needs to be in a network accessible environment via main body NIC, as data is exported/imported via network. To import/export the non-volatile data of parameter board, perform the following: Preparation on the main body: 1. Access [Utility Menu] => [Machine Manager Setting] => [Network Setting] => [Machine NIC Setting]. Perform the network setting of the main bodyNIC. 2. TurnOFF/ON the power switch. Enter the Service mode.

Preparation on the Web browser: 1. On the Web browser, access the Web Utilities of the main body NIC. 2. Select [Extension for maintenance]. 2. Enter 'ce' for User Name. 4. Enter CE password for Password (default is 92729272).5. Select [Machine Setting data Import/Export]. Caution : If 'Access deny in the present machine mode' message, the main body may not be in the Service mode.

How to export : 1. Select [Submit] which is under Export on the browser screen. 2. Save the data following the screen instructions.

How to import : 1. Select [Browse] which is under Import on the browser screen. Select backup datathat has been saved. 2. Select [Submit] which is under Import.

Considerations: When importing the data, the machine serial number is not checked. Be careful not to import data of a different machine.


DescriptionDrum claw operation does not operate (Side 2 only).

128


bizhub PRO 920

Solution CAUSE: It is not a settings problem because dipswitch 7-7 is correctly set to 1. It is a firmware bug issue. SOLUTION: Install the countermeasure firmware (I:20-0000 or above). Note : The latest version firmware or system software is available via the Konica Minolta Download Selector. Access the Selector from SSD Web Support(CS Expert Support) by clicking on 'Download MSDS, Drivers, Firmware and more'.


DescriptionUsing Macintosh® O/S 10.4.9, the duplex option is grayed out in the printer driver Properties.

Solution CAUSE: The duplex option islocated in the Layout section of the driver. SOLUTION: To select the duplex option in the print driver, select Layout, Binding and then Double-sided.


DescriptionLRS VPS is not printing to the printer. LRS VPS is a HOST application which transforms IBM® EBCDIC print jobs to ASCII. When set up to printRAW to Port9100 or 10001, the job does not print.

Solution CAUSE:VPS is looking for an acknowledgementfrom the printer that the previous packet has been received.By default,theKonica Minolta printer does notsend the acknowledgement. SOLUTION:For the bizhub PRO 1050,load minimum firmware30-COK0 and setsoft switch 43-5 to1. For the bizhub PRO 920,load minimum firmware20-COK0and set soft switch 43-5 to1. Note : The latest version firmware or system software is available via the Konica Minolta Download Selector. Access the Selector from SSD Web Support(CS Expert Support) by clicking on 'Download MSDS, Drivers, Firmware and more'.


DescriptionHow to set up Secure/Password printing.

Solution To set up Secure/Password print, perform the following: 1.In the print driver, select the output method and then select Secure.Secure printing is the same as Password printing.2.Enter a secure print ID and password.The user ID and password can be any combination of numbers and characters.3.Select the BOX hard key on the operation panel.4.Select RECALL.5.Select SECURE.6.Selectthe user ID and press OK.7.Enterthe password and press OK.8.Select the documents to print, press the right-arrow to move them into the print field and press OK.


DescriptionFS-604, SC77-04 after the paper exits the finisher.The exit rollers never stop but do slow down.

Solution CAUSE: The coupling geardrive pin that drives the exit belt has sheared off. SOLUTION: Replace the failed gear coupling (p/n 129U 7704 1).


DescriptionA paper exit tray is available for customer environments where a finishing unit is not installed.

Solution

129


bizhub PRO 920

Paper exit tray (p/n 540012114) may be used on the bizhub PRO 920. There will be limited stacking ability.


DescriptionSC33-01.

Solution CAUSE: Contact failure of connectors CN521/CN560/CN563. SOLUTION: Check and correct the connection for CN521/CN560/CN563.


DescriptionClose Front Door message.

Solution CAUSE: DCPS 1 has failed. SOLUTION: Replace the DCPS 1 (p/n 65UA84510).


Description How to perform Print Screens (screen shots) from a Microsoft® Windows OS and Macintosh® OS.

Solution Please see the attacheddocument for detailed information. Note : To view a PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at: http://www.adobe.com/products/acrobat/readstep2.html


DescriptionThequantity of copies listed on the control panel always defaults to 000, instead of 001.

Solution CAUSE: Incorrect settings. SOLUTION: Perform the following: 1. Press the Utility button. 2. Select Copier Setting. 3. Select Reset Setting. 4. Select Initial Setting. 5. Select Factory Default. 6. Exit the Utility mode.


DescriptionSC29-09.

Solution CAUSE: Contact failure of connectors, CN350/CN340/CN225. SOLUTION: Check and correct the connection of CN350/CN340/CN225.


DescriptionIs the FS-604 finisher stapleralignmentjig the same as the FS-110 jig?

SolutionThe stapler alignment jig is the samefor the FS-604 and the FS-110.

130


bizhub PRO 920


DescriptionWhen the Zoom is set to a percentage other than 100% andSheet/Cover/Chapter Insert and Page Margin is selected, the Zoom will reset back to 100% assoon as the original is placed in the ADF. This will occur whether setting the job manually from the operation panel or creating a Mode Memory Job.

Solution CAUSE: This is the specification of the sheet insertion mode of the bizhub PRO 920. When the sheet insertion mode is selected, AMS is automaticallyselected. As the result, the magnification returns to 100% when document is placed in ADF or changes according to the sizes of document and copy paper.

SOLUTION: To avoid this, set zoom after selecting the sheet insertion mode: 1. Select Sheet/Cover/Chapter Insert => Insert Sheet => Front Cover => Cover/Blank. 2. Set Page Margin => Front => Right 15/Bottom 0. 3. Set x0.950 magnification. 4. Store the setting in Mode Memory. 5. Recall the setting. The magnification will remain atx0.950 when the document is placed in the ADF.


DescriptionIs 12x18 paper supported?

Solution When running 12x18 paper, the bypass tray or the LU-404 must be used as this paper will not fit in paper trays 1, 2 and 3.


DescriptionUnable to print from Microsoft® Windows 2003 server. Printer listed as off-line when viewed from the Printers window. Able to print via LPR butnot RAW.AbletoPING and browse the NIC from a workstation.

Solution CAUSE:SNMP (port 161) is disabled on the controller. SOLUTION: To enable SNMP on the controller, perform the following:1. Access the Machine Manager Setting(press the Utility/Counter key). 2. Touch [06 Machine Manager Setting] on the touchscreen.3. Touch [04 Network Setting] on the touchscreen. 4. Touch [02 Controller NIC Setting]on the touchscreen sub menu. 5. Touch [05 SNMP ]on the touchscreen. 6. Set SNMP to USE. 7. Set Read Community Name = public. 8. Set Write Community Name = private. 9. Touch OK. 10.Reboot the engine and controller using the main power switch.



Solution CAUSE: The ADU CB has failed. SOLUTION: Reseat all connectors on the ADU CB and replace the boardif required (p/n 57GA-9070).


DescriptionSC32-06.

Solution PROBABLE CAUSES:

131


bizhub PRO 920

1.ICP10on the ADU Drive Board is OPEN. Replace the ADU Drive Board (p/n 57GA-908 0). 2.Contact failure of connector (CN592/CN525). Check and correct the connection of (CN592/CN525).


DescriptionMicroPress® is printing "garbage" and no print jobs have been sent to the printer.

Solution CAUSE: The IC-203 controller is not at firmware version 70. SOLUTION: Upgrade thecontroller to minimum version 70. Note : The latest version firmware or system software is available via the Konica Minolta Download Selector. Access the Selector from SSD Web Support(CS Expert Support) by clicking on 'Download MSDS, Drivers, Firmware and more'.


DescriptionVarious J72 codes and the paper is crashing into the finisher when performing a fold and staple operation for a print job.

Solution CAUSE: Incorrect settings in the print driver. SOLUTION: When performing a fold and staple print job do not select Multi-fold with Center Fold and Staple together. Select only Center Fold and Staple inthe print driver. Note : This problem is more prevalent when running more then 3 sets.


Description How to release a secure print job from the main body.

Solution To release a secure print job from the main body perform the following: 1. Press the hard BOX key on the operation panel. 2. Press the RECALL icon on the touchscreen. 3. Press SECURE. 4. Enter secure print ID and password.


DescriptionHow to enable/disable original glass APS.

Solution To enable/disable original glass APS, perform the following: 1. Press the Utility/Counter key. 2. Touch [3 Copier Setting] on the touchscreen. 3. Touch [2 Each Function Setting] on the touchscreen. 4. Touch [Original Glass APS] on the touchscreen. 5. Touch [On] or [Off] as desired by the customer. 6. Touch [Exit] on the touchscreen to return to the normal screen.


DescriptionHow to allow/restrict user changing of zoom ratio.

Solution To enable/disable user changing of zoom ratio, perform the following: 1. Press the Utility/Counter key. 2. Touch [6 Administrator Setting] on the touchscreen. 3. Enter the Administrator Password (default password is 12345678). 4. Touch [OK] on the touchscreen.

132


bizhub PRO 920

5. Touch [1 System Setting] on the touchscreen. 6. Touch [5 Prohibit User Operation] on the touchscreen. 7. Touch [Changing Zoom Ratio] on the touchscreen. 8. Touch [Allow] or [Restrict] on the touchscreen as desired by the customer. 9. Touch [Exit] on the touchscreen to return to the normal screen


Description Fan Wiring: Code SC42-05, SC42-09, SC42-13

Solution CAUSE: Pinched or damaged wiring to the motor cooling fan can cause several different symptoms: Error code SC42-05 Error code SC42-09 Error code SC42-13 Toner deterioration (spewing or poor copy quality) The damage occurs when the wiring gets pinched between the frame and the right side cover, either during production or field maintenance. Tonerdeterioration occurs because the machine’s internal temperature rises due to the fan not working. The fan EM signal may be detected as normal, dependingupon which wire is damaged. SOLUTION: To prevent a possible problem, the motor cooling fan wiring behind the main body right side cover should be checked and repositioned using the procedurebelow. If the wiring has already been damaged, it should be repaired. This inspection should be performed on all bizhub 920 machines belowserial number. 57GE00594. PROCEDURE: 1. Remove the LU-403 or LU-404. a. Open the front door of the LU b. Remove the 4 screws that secure the LU to the main body. c. Disconnect the LU wiring connector from the main body. 2. Remove the main body right side cover (4 screws). 3. Check the wiring for damage. a. Check whether the insulation on the wiring is damaged in the area indicated by the red circle. b. If it is damaged, use electrical tape to cover the damaged portion. 4. Change the wiring path. a. Remove the wiring from saddle/1 and reposition in into saddle/2. 5. Because the wiring will be loose, wind the excess around saddle/3 and secure it with a clamp. 6. Reinstall the right side cover and teh LU-403 or LU-404. Illustrated instructions can be found inBulletin #6115, attached. Note: To view a PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at: http://www.adobe.com/products/acrobat/readstep2.html


DescriptionThe firmware version is displayed in the service mode.Why isthereno selection in ISW to flash the ZU-602?

Solution The firmware for the ZU-602 is stored on a conventional EPROM, not flash ROM. The firmware can be upgraded using an EPROM burner and the firmwarefile is available on the Konica Minolta web site. Notes : 1. If an EPROM burner is not available, the EPROM can be ordered (p/n 15KSR70300). 2. The latest version firmware or system software is available via the Konica Minolta Download Selector. Access the Selector from SSD Web Support (CSExpert Support) by clicking on 'Download MSDS, Drivers, Firmware and more'.

133


bizhub PRO 920


DescriptionHow to adjust the touchscreen buzzer volume.

Solution To adjust the touchscreen buzzer volume, perform the following: 1. Press the Utility/Counter key. 2. Touch [1 System Setting] on the touchscreen. 3. Touch [2 Buzzer Setting] on the touchscreen. 4. Touch [1 Buzzer On/Off Volume Setting] on the touchscreen. 5. Under Touch Panel Volume Adjust repeatedly touch [Small] or [Big] until the desired touchscreen volume is obtained. 6. Touch [OK] on the touchscreen. 7. Touch [Exit] on the touchscreen.


Description What are the recommended labels?

SolutionThe recommended labels are Avery® 5160 or Avery® DSP24.


DescriptionPrinting to a Windows Samba shared printer from a Macintosh®.

Solution Please perfrom the step-by-step procedure mentioned in the attached document. Note : To view a PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at: http://www.adobe.com/products/acrobat/readstep2.html


Description Intermittently the NIC will lock up and can not be PINGed. Power must be recycled to restore the NIC.

Solution CAUSE: The NIC is set to AUTO for the line speed. SOLUTION: Change the NIC settings to 100M Half Duplex by performing the following: 1. Press the Utility key. 2. Select Administrator mode and enter password. 3. Select Network Settings. 4. Select IP NIC. 5. Select TCP/IP and press the NEXT icon. 6. Select 100M Half Duplex and press OK.


DescriptionStaples are skewed when making booklets.

Solution CAUSE: A failed front stopper and mylar. SOLUTION: Replace the front stopper (p/n 15JM43310) and the mylar (p/n 13QJ42480).


DescriptionJam occurs if a job stored on the main body HDD is deleted while in output operation. It tends to occur if a large volume job is deleted.

Solution CAUSE: Due to the performance limitation of the system, if a large volume job is deleted during print operation, the operation cannot be processed in time,resulting in paper jam.

134


bizhub PRO 920

SOLUTION: Delete jobs stored in the HDD during idle. SPECIAL NOTE : Solution contribution from KMBT, Japan.


DescriptionSC52-08.

Solution PROBABLE CAUSES: 1. ICP 6 on the ADU Drive Board is OPEN. Replace the ADU Drive Board (p/n 57GA-908 0). 2. Contact failure of connector (CN420/CN179/CN173). Check and correct the connection of (CN420/CN179/CN173).


Description Unable to print and cannotPING the IC-203 NIC.

Solution CAUSE: The NVRAM has failed. SOLUTION: Please call the SSD Hotline to log a new ticket which is needed to order the NVRAM on-line.

135


920

Documents

Transcript of 920