8mm Framed Plus Sliding and Side Panel V01.06.2016...make sure the tray is level, using a spirit...
Transcript of 8mm Framed Plus Sliding and Side Panel V01.06.2016...make sure the tray is level, using a spirit...
8mm FRAMED PLUS SLIDING
This product is universal, not handed
WITH SIDE PANELRefer To Sheet 13 For Relevant Product Codes
VictoriaPlum.com0344 804 48 48
1
BEFORE YOU START, HERE IS SOME IMPORTANT INFORMATION
1) General Information
2) Additional Notes
Please inspect this product upon delivery, any missing parts or manufacturing
defects must be reported immediately to the supplier. Damage or defects reported
later will not be accepted. TAKE CARE WHEN HANDLING GLASS PARTS - AVOID
HEAVY CONTACT BETWEEN THE GLASS EDGES AND ANY HARD SURFACE.
Glass breakage claims will not be accepted after the product has been unpacked.
Please note: Aluminium is a soft metal, and undergoes a series of extrusion,
fabrication, polishing and anodising processes in order to create your finished
shower enclosure. Some light surface marks are normal, and is a result of the
manufacturing processes. Quality control has ensured that this item is of a good
standard, and is fit for purpose.
Please read these instructions carefully before starting installation.Special care should be taken when drilling walls to avoid hidden pipes or electrical cables.
Note: this product is heavy and may require two people to install.
This product is heavy and may require two people to install.
TOOLS REQUIRED
Ø3mm Drill bit
Ø6mm Drill bit
Pencil
Spirit level
Tape measure
DESCRIPTION DESCRIPTIONPART IMAGE PART IMAGE
Drill
Flat-headScrewdriver
Cross headScrewdriver
Mallet
Silicone Sealant
PZ1
2
8x Wall Plugs
2x Wall Post Cover caps
2x Wall Profiles
2x Cover Strip
3x Vertical Covers
1x Side Panel
1x Corner Post Cover Cap
9x Screws 4x12
(9) 1x Corner Post Cover Strip
8x Screws 4x40
1x Upright Magnet Profile
1x Magent Seal
2x Top And Bottom Profiles
2x Top Rollers
1x Moving Panel
1x Supplied Separately)Handle (
2x Bottom Rollers
1x Moving Panel Seal
1x Fixed Panel Seal
2x Bottom Seal
1x Fixed Panel
8x Screws 4x30
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(10)
(11)
(12)
(13)
(14)
(15)
(16)
(17)
(18)
(19)
(20)
(21)
(22)
(1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (11) (12) (13) (15)(14)
(19)(17) (18)(16) (20) (21) (22)
ASSEMBLY INSTRUCTIONS - DRAWING
76
0/8
00
/90
0
10
10
10
10
10101200/1400/1600
10
10
10
3
1200/1400/1600
10
10
10
10
THESE DIMENSIONS ASSUME THE WALLS ARE PLUMB AND THE SHOWER TRAY IS LEVEL, AND THAT THE WALLS ARE TILED DOWN TO THE TOP OF THE TRAY USING A 10mm TILE/WET WALL PANEL.
ASSEMBLY INSTRUCTIONSIf you require help, we advise you to contact a competent plumber Installation Steps
FITTED SLIDING DOOR AND SIDE PANEL DRAWING
Installation Steps
4
Round ScrewST4X40
1a 1b 1c
2a 2b 2c
3a
3b
1b
1c
2b
2c
3a
3b
MAKE SURE THE TRAY IS LEVEL, USING A SPIRIT LEVEL, BEFORE INSTALLING THIS
SHOWER PANEL / DOOR,
Step 1 ASSEMBLE FRAME AND FIXED PANEL
VIEW FROM INSIDE
VIEW FROM INSIDE
1a
2a
5
10mm 10mm
Step 2 SLIDE WALL PROFILE ON TO FIXED PANEL
Step 3 MARK WALL FIXING POSITIONS
VIEW FROM INSIDE
6
Round ScrewST4X30
VIEW FROM INSIDE
VIEW FROM INSIDE
Step 4 DRILL WALL HOLE
Step 5 SCREW THE WALL PROFILE TO THE WALL
6mm Drill Bit
7
Round ScrewST4X12
3mm Drill Bit
Step 6 SECURING THE WALL PROFILES + COVER STRIP
Step 7 FITTING THE TOP AND BOTTOM ROLLERS
VIEW FROM INSIDE
VIEW FROM INSIDE
L=0~20mmL 5mm/R≥ ≥10mm
R
L 5mm/R≤ ≥15mm
1
2
3
8
Ensure wall profiles are plumb. Adjust enclosure to be square and level. Wheels should be adjusted to square the doors andensure smooth running,using the adjusting screws underneath the top rollers.
Fixed PanelDoor Panel
1 2
3 4
1a
1b
2
3
1a
1b
23
Step 8 FITTING THE MOVING PANEL ON TO THE PROFILE
Step 9 FITTING THE SEALS VIEW FROM INSIDE
VIEW FROM INSIDE
999
Step 10 FITTING THE TOP CAPS AND HANDLE
Step 11 SILICONE THE OUTSIDE EDGES
Allow 24 hours for silicone to dry before use. Silicone on the
outside edge only, NOT THE INSIDE
10mm
10
6mm Drill Bit
CORNER INSTALLATION WITH SIDE PANEL
Step 1
Step 3
Step 2 DRILL WALL HOLE
Step 4 FITTING THE SIDE PANEL
VIEW FROM INSIDE
MARK THE CORRECT DRILL HOLE POSITIONS ON THE WALL
SLIDE WALL PROFILE ON TO THE SIDE PANEL
FOLLOW SLIDING DOOR STEPS 1 & 2 FIRST THEN COMBINE WITH THESE STEPS
6mm Drill Bit
11
Round ScrewST4X30
3mm Drill Bit
Step 5 SCREW THE WALL PROFILE TO THE WALL
Step 6 SECURING THE SIDE PANEL AND PROFILE COVER STRIP
VIEW FROM INSIDE
VIEW FROM INSIDE
VIEW FROM INSIDE
VIEW FROM INSIDE
3mm Drill Bit
Round ScrewST4X12
Round ScrewST4X12
2
1
3
4
5
6
L=0~20mmL 5mm/R≥ ≥10mm
R
L 5mm/R≤ ≥15mm
Step 7 FITTING THE TOP CAPS
12
Step 8 SILICONE THE OUTSIDE EDGES
Allow 24 hours for silicone to dry before use. Silicone on the
outside edge only, NOT THE INSIDE
13
Product name: 8mm Framed Plus Sliding and Side Panel
Product code: LSD1001 LSD1201 LSD1401 LSD1601 LSD1701 LSP701 / / / / /
Customer help line number: 0344 804 48 48
CARE AND MAINTENANCE
COMMITMENT TO QUALITY
1) AFTER CARE INSTRUCTIONS
2) MAINTENANCE
Regularly clean your shower product with warm soapy water
Clean the plastic parts with a cloth and mild detergent. Never
use any abrasive creams, dissolvents, acetone or detergents
and disinfectants that contain chlorine. The supplier acceptsno liability for any type of use of care other than those contained
in these instructions. The supplier reserves the right to introduce
technical changes without notice.
It is our intention that the quality and functions of this productare of the highest standard. If you require help we advise you
firstly contact a competent plumber. However we understand that
this may not always be the case, so should you experience
any problems please contact our customer services quoting
the following:
to prevent lime scale build up. Do not use abrasive cleaning
fluids or materials, or strong chemical cleaners as this will
damage the product surface.
LSP801 / LSP901
14
INSTALLERS NOTES
The packaging you have received with your product is 100% recyclable.It must be disposed of in a safe and environmentally friendly way.
We suggest you take it to the local landfill site and discard in the designated bins.
Victoria Plum Limited, Bridgehead Business Hessle, HU13 0DG
Park
16
EN 14428:2004+A1:2008
DOP No.:J160415002
Shower enclosures with aluminiumprofiles and safety glass
Essentialcharacteristics
Performance Harmonisedtechnical
specificationCleanability
Impactresistance/shatter
properties
Pass
Pass
PassDurability
Clause 4.2 of EN14428:2004+A1:
2008Clause 4.3 of EN14428:2004+A1:
2008Clause 4.4 of EN14428:2004+A1:
2008
V01.06 2016.