865GM3/865PEM2 Seriesmsi-ftp.de/Manuals/6763-englv1.0-865GM3865PEM2Series.pdf · 2009-08-19 ·...

70
Version 1.0 G52-M6763X1-G22 MS-6763 (v1.X) M-ATX Mainboard 865GM3/865PEM2 Series

Transcript of 865GM3/865PEM2 Seriesmsi-ftp.de/Manuals/6763-englv1.0-865GM3865PEM2Series.pdf · 2009-08-19 ·...

Page 1: 865GM3/865PEM2 Seriesmsi-ftp.de/Manuals/6763-englv1.0-865GM3865PEM2Series.pdf · 2009-08-19 · 865GM3/865PEM2 Series. ii Manual Rev: 1.0 Release Date: July 2003 FCC-B Radio Frequency

i

Version 1.0G52-M6763X1-G22

MS-6763 (v1.X) M-ATX Mainboard

865GM3/865PEM2 Series

Page 2: 865GM3/865PEM2 Seriesmsi-ftp.de/Manuals/6763-englv1.0-865GM3865PEM2Series.pdf · 2009-08-19 · 865GM3/865PEM2 Series. ii Manual Rev: 1.0 Release Date: July 2003 FCC-B Radio Frequency

ii

Manual Rev: 1.0Release Date: July 2003

FCC-B Radio Frequency Interference Statement

This equipment has been tested and found to comply with the limits for a classB digital device, pursuant to part 15 of the FCC rules. These limits are designedto provide reasonable protection against harmful interference when the equip-ment is operated in a commercial environment. This equipment generates, usesand can radiate radio frequency energy and, if not installed and used in accor-dance with the instruction manual, may cause harmful interference to radiocommunications. Operation of this equipment in a residential area is likely tocause harmful interference, in which case the user will be required to correctthe interference at his own expense.

Notice 1The changes or modifications not expressly approved by the party respon-sible for compliance could void the user’s authority to operate the equipment.

Notice 2Shielded interface cables and A.C. power cord, if any, must be used in order tocomply with the emission limits.

VOIR LA NOTICE D’INSTALLATION AVANT DE RACCORDER AURESEAU.

Micro-Star International MS-6763

Tested to comply with FCC Standard

For Home or Office Use

Page 3: 865GM3/865PEM2 Seriesmsi-ftp.de/Manuals/6763-englv1.0-865GM3865PEM2Series.pdf · 2009-08-19 · 865GM3/865PEM2 Series. ii Manual Rev: 1.0 Release Date: July 2003 FCC-B Radio Frequency

iii

Copyright Notice

The material in this document is the intellectual property of MICRO-STARINTERNATIONAL. We take every care in the preparation of this document,but no guarantee is given as to the correctness of its contents. Our productsare under continual improvement and we reserve the right to make changeswithout notice.

Trademarks

All trademarks are the properties of their respective owners.

Intel® and Pentium® are registered trademarks of Intel Corporation.PS/2 and OS®/2 are registered trademarks of International Business MachinesCorporation.Windows® 95/98/2000/NT/XP are registered trademarks of MicrosoftCorporation.Netware® is a registered trademark of Novell, Inc.Award® is a registered trademark of Phoenix Technologies Ltd.AMI® is a registered trademark of American Megatrends Inc.

Revision HistoryRevision Revision History DateV1.0 First release for PCB 1.X July 2003

Technical Support

If a problem arises with your system and no solution can be obtained from theuser’s manual, please contact your place of purchase or local distributor.Alternatively, please try the following help resources for further guidance.

Visit the MSI website for FAQ, technical guide, BIOS updates, driverupdates, and other information: http://www.msi.com.tw/

Contact our technical staff at: [email protected]

Page 4: 865GM3/865PEM2 Seriesmsi-ftp.de/Manuals/6763-englv1.0-865GM3865PEM2Series.pdf · 2009-08-19 · 865GM3/865PEM2 Series. ii Manual Rev: 1.0 Release Date: July 2003 FCC-B Radio Frequency

iv

1. Always read the safety instructions carefully.2. Keep this User’s Manual for future reference.3. Keep this equipment away from humidity.4. Lay this equipment on a reliable flat surface before setting it up.5. The openings on the enclosure are for air convection hence protects the

equipment from overheating. DO NOT COVER THE OPENINGS.6. Make sure the voltage of the power source and adjust properly 110/220V

before connecting the equipment to the power inlet.7. Place the power cord such a way that people can not step on it. Do not

place anything over the power cord.8. Always Unplug the Power Cord before inserting any add-on card or module.9. All cautions and warnings on the equipment should be noted.10. Never pour any liquid into the opening that could damage or cause electri-

cal shock.11. If any of the following situations arises, get the equipment checked by a

service personnel:The power cord or plug is damaged.Liquid has penetrated into the equipment.The equipment has been exposed to moisture.The equipment has not work well or you can not get it work accordingto User’s Manual.The equipment has dropped and damaged.The equipment has obvious sign of breakage.

12. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENTUNCONDITIONED, STORAGE TEMPERATURE ABOVE 600 C (1400F), ITMAY DAMAGE THE EQUIPMENT.

Safety Instructions

CAUTION: Danger of explosion if battery is incorrectly replaced.Replace only with the same or equivalent type recommended by themanufacturer.

Page 5: 865GM3/865PEM2 Seriesmsi-ftp.de/Manuals/6763-englv1.0-865GM3865PEM2Series.pdf · 2009-08-19 · 865GM3/865PEM2 Series. ii Manual Rev: 1.0 Release Date: July 2003 FCC-B Radio Frequency

v

CONTENTSFCC-B Radio Frequency Interference Statement .......................................... iiiCopyright Notice .......................................................................................... iiiRevision History ........................................................................................... iiiTechnical Support ......................................................................................... iiiSafety Instructions ....................................................................................... ivChapter 1. Getting Started ........................................................................ 1-1

Mainboard Specifications .................................................................... 1-2Mainboard Layout ............................................................................... 1-4

Chapter 2. Hardware Setup ....................................................................... 2-1Quick Components Guide .................................................................... 2-2Central Processing Unit: CPU .............................................................. 2-3

CPU Core Speed Derivation Procedure ......................................... 2-3CPU Installation Procedures for Socket 478 .................................. 2-4Installing the CPU Fan .................................................................. 2-5

Memory ................................................................................................ 2-7Memory Speed/CPU FSB Support Matrix ..................................... 2-7DDR Population Rules .................................................................. 2-7Installing DDR Modules ............................................................... 2-8

Power Supply ....................................................................................... 2-9ATX 20-Pin Power Connector: ATX1 ............................................ 2-9ATX 12V Power Connector: JPW1 ................................................ 2-9

Back Panel .......................................................................................... 2-10Mouse/Keyboard Connector ...................................................... 2-11Serial Port Connectors: COMA & JCOM1 .................................. 2-11VGA Connector (for 865GM3 Series only) .................................. 2-11Parallel Port Connector: LPT1 ...................................................... 2-13LAN Jack: 10/100Mbps LAN (for 865PEM2 Series) or Gigabit LAN(for 865GM3 Series) ..................................................................... 2-13IEEE1394 Port (Optional for 865PEM2 Series only) ..................... 2-14

Page 6: 865GM3/865PEM2 Seriesmsi-ftp.de/Manuals/6763-englv1.0-865GM3865PEM2Series.pdf · 2009-08-19 · 865GM3/865PEM2 Series. ii Manual Rev: 1.0 Release Date: July 2003 FCC-B Radio Frequency

vi

USB Connectors .......................................................................... 2-14Audio Port Connectors ............................................................... 2-15

Connectors ......................................................................................... 2-16Floppy Disk Drive Connector: FDD1........................................... 2-16Chassis Intrusion Switch Connector: JCI1 (Optional) ................. 2-16Ultra ATA HDD Connectors: IDE1, IDE2 .................................... 2-17Serial ATA HDD Connectors: SATA1, SATA2 ............................ 2-18Fan Power Connectors: CPU_FAN/SYS_FAN ............................ 2-19CD-In Connector: JCD1 ............................................................... 2-20Modem-In Connector: JMD1 (Optional) ..................................... 2-20Aux Line-In Connector: JAUX1 (Optional) ................................. 2-20SPDIF-Out Connector: JSP1 (Optional) ....................................... 2-20Front Panel Connectors: JFP1 ..................................................... 2-21Front Panel Audio Connector: JAUD1 ........................................ 2-22Front USB Connectors: JUSB1, JUSB2........................................ 2-23IEEE 1394 Connector: J1394_1 (Optional for 865PEM2 Series) .... 2-24

Jumpers .............................................................................................. 2-25Clear CMOS Jumper: JBAT1 ........................................................ 2-25

Slots ................................................................................................... 2-26AGP (Accelerated Graphics Port) Slot ......................................... 2-26PCI (Peripheral Component Interconnect) Slots .......................... 2-26CNR (Communication Network Riser) Slot .................................. 2-26PCI Interrupt Request Routing .................................................... 2-27

Chapter 3. BIOS Setup .............................................................................. 3-1Entering Setup ...................................................................................... 3-2

Control Keys ................................................................................. 3-2Getting Help .................................................................................. 3-3

The Main Menu ................................................................................... 3-4Standard CMOS Features .................................................................... 3-6Advanced BIOS Features .................................................................... 3-8Advanced Chipset Features ............................................................... 3-12

Page 7: 865GM3/865PEM2 Seriesmsi-ftp.de/Manuals/6763-englv1.0-865GM3865PEM2Series.pdf · 2009-08-19 · 865GM3/865PEM2 Series. ii Manual Rev: 1.0 Release Date: July 2003 FCC-B Radio Frequency

vii

Integrated Peripherals ........................................................................ 3-15Power Management Setup ................................................................. 3-21PNP/PCI Configurations ..................................................................... 3-25PC Health Status ................................................................................ 3-27Frequency/Voltage Control ................................................................ 3-29Load Default Setting .......................................................................... 3-30Set Supervisor/User Password ........................................................... 3-31

Page 8: 865GM3/865PEM2 Seriesmsi-ftp.de/Manuals/6763-englv1.0-865GM3865PEM2Series.pdf · 2009-08-19 · 865GM3/865PEM2 Series. ii Manual Rev: 1.0 Release Date: July 2003 FCC-B Radio Frequency

1-1

Getting Started

Chapter 1. Gett ingStarted

Thank you for choosing the 865GM3/865PEM2 Series(MS-6763 v1.X) micro ATX mainboard. The 865GM3/865PEM2Series are based on Intel® Springdale-G/PE & ICH5 chipsetsfor optimal system efficiency. Designed to fit the advanced Intel®

Pentium® 4 processors in 478 pin package, the 865GM3/865PEM2Series deliver a high performance and professional desktop plat-form solution.

Getting Started

Page 9: 865GM3/865PEM2 Seriesmsi-ftp.de/Manuals/6763-englv1.0-865GM3865PEM2Series.pdf · 2009-08-19 · 865GM3/865PEM2 Series. ii Manual Rev: 1.0 Release Date: July 2003 FCC-B Radio Frequency

1-2

MS-6763 M-ATX Mainboard

Mainboard Specifications

CPU Supports Intel® P4 Northwood (Socket 478) processors. FSB 533~800MHz, depending on the CPU installed. Supports up to 3.2GHz.

Chipset Intel® Springdale-PE/G chipset- Supports FSB 800/533/400MHz.- Supports AGP 8X/4X interface.- Supports DDR 400/333/266 memory interface.- Integrated graphics (for Springdale-G only).

Intel® ICH5 chipset- Hi-Speed USB (USB2.0) controller, 480Mb/sec.- 2 Serial ATA/150 ports.- 2 channel Ultra ATA 100 bus Master IDE controller.- PCI Master v2.3.- I/O APIC.- AC’97 2.3 interface.- Supports both ACPI and legacy APM power management.

Main Memory Supports four 184-pin unregistered non-ECC PC3200/PC2700/PC2100 DDRDIMMs.

Supports up to 4GB memory size.

SlotsOne AGP slot supports 8x/4x at 0.8V (AGP 3.0) or 4x at 1.5V (3.3V notsupported).Three 32-bit v2.3 Master PCI bus slots (support 3.3v/5v PCI bus interface).One CNR slot.

On-Board IDEDual Ultra DMA 33/66/100 IDE controllers integrated in ICH5.- Supports PIO, Bus Master operation modes.- Can connect up to four Ultra ATA drives.Serial ATA/150 controller integrated in ICH5.- Up to 150MB/sec transfer speeds.- Can connect up to two Serial ATA drives.

Page 10: 865GM3/865PEM2 Seriesmsi-ftp.de/Manuals/6763-englv1.0-865GM3865PEM2Series.pdf · 2009-08-19 · 865GM3/865PEM2 Series. ii Manual Rev: 1.0 Release Date: July 2003 FCC-B Radio Frequency

1-3

Getting Started

On-Board Peripherals On-Board Peripherals include:- 1 floppy port supports 2 FDDs with 360K, 720K, 1.2M, 1.44M and

2.88Mbytes- 2 serial ports (COM A & JCOM1)- 1 parallel port supports SPP/EPP/ECP mode- 1 VGA port (for 865GM3 Series only)- 8 USB 2.0 ports (Rear * 4/ Front * 4)- 1 Line-In/Line-Out/Mic-In port- 1 RJ45 LAN jack- 2 IEEE 1394 ports (optional for 865PEM2 Series only)

AudioAC97 link controller integrated in ICH5.Software audio codec AD1981B.- Compliant with AC97 v2.2 spec.- Meets PC2001 audio performance requirement.- Can support SPDIF Out via bracket only.

LANIntel 82547EI (for 865GM3 Series only)- Integrated 10/100/1000Mbps Ethernet MAC and PHY in one chip.- Supports auto-negotiation operation.- Compliant with PCI v2.2, and LAN on Motherboard (LOM) standard.RealTek RTL8101L (for 865PEM2 Series only)- Integrated 10/100Mbps Ethernet MAC and PHY in one chip.- Supports 10Mb/s and 100Mb/s auto-negotiation operation.- Compliant with PCI v2.2, and LAN on Motherboard (LOM) standard.

BIOS The mainboard BIOS provides “Plug & Play” BIOS which detects the pe-ripheral devices and expansion cards of the board automatically.

The mainboard provides a Desktop Management Interface (DMI) functionwhich records your mainboard specifications.

Dimension Micro ATX Form Factor: 24.38 cm (L) x 24.38 cm (W).

Mounting 8 mounting holes.

Page 11: 865GM3/865PEM2 Seriesmsi-ftp.de/Manuals/6763-englv1.0-865GM3865PEM2Series.pdf · 2009-08-19 · 865GM3/865PEM2 Series. ii Manual Rev: 1.0 Release Date: July 2003 FCC-B Radio Frequency

1-4

MS-6763 M-ATX Mainboard

Mainboard Layout

865PEM2 Series (MS-6763 v1.X) Micro ATX Mainboard

DIM

M 1

DIM

M 3

DIM

M 2

DIM

M 4

AGP Slot

T: Mouse B: Keyboard

T: Line-Out

B: Mic

Line-InM:

JSP1

CNR

JCD1

JMD1

JAUX1Codec

RealTekRTL8101L

NECD72874GC

BATT+

BIOS

Win

bond

8362

7HF-

AW

ICH5

Intel865PE

IDE

1

IDE

2

FDD

1

PCI Slot 1

PCI Slot 2

PCI Slot 3

CPU_FAN

JCOM1

SYS_FAN

JFP1

JPW1

ATX

1

J1394_1

JBAT1

JCI1

JUSB1

SATA2SATA1

JUSB2JAUD1

Page 12: 865GM3/865PEM2 Seriesmsi-ftp.de/Manuals/6763-englv1.0-865GM3865PEM2Series.pdf · 2009-08-19 · 865GM3/865PEM2 Series. ii Manual Rev: 1.0 Release Date: July 2003 FCC-B Radio Frequency

1-5

Getting Started

DIM

M 1

DIM

M 3

DIM

M 2

DIM

M 4

AGP Slot

T: Mouse B: Keyboard

T: Line-Out

B: Mic

Line-InM:

JSP1

CNR

JCD1

JMD1

JAUX1Codec

Intel82547EI

BATT+

BIOS

Win

bond

8362

7HF-

AW

ICH5

Intel865G

IDE

1

IDE

2

FDD

1

PCI Slot 1

PCI Slot 2

PCI Slot 3

CPU_FAN

JCOM1

SYS_FAN

JFP1

JPW1

ATX

1

JBAT1

JCI1

JUSB1

SATA2SATA1

JUSB2JAUD1

865GM3 Series (MS-6763 v1.X) Micro ATX Mainboard

Page 13: 865GM3/865PEM2 Seriesmsi-ftp.de/Manuals/6763-englv1.0-865GM3865PEM2Series.pdf · 2009-08-19 · 865GM3/865PEM2 Series. ii Manual Rev: 1.0 Release Date: July 2003 FCC-B Radio Frequency

2-1

Hardware Setup

Chapter 2. HardwareSetup

Hardware Setup

This chapter provides you with the information about hard-ware setup procedures. While doing the installation, be carefulin holding the components and follow the installationprocedures. For some components, if you install in the wrongorientation, the components will not work properly.

Use a grounded wrist strap before handling computercomponents. Static electricity may damage the components.

Page 14: 865GM3/865PEM2 Seriesmsi-ftp.de/Manuals/6763-englv1.0-865GM3865PEM2Series.pdf · 2009-08-19 · 865GM3/865PEM2 Series. ii Manual Rev: 1.0 Release Date: July 2003 FCC-B Radio Frequency

2-2

MS-6763 M-ATX Mainboard

Quick Components Guide

JBAT1, p.2-25

DDR DIMMs, p.2-7

CPU_FAN, p.2-19

FDD1, p.2-16

JCI1, p.2-16

JUSB1/2, p.2-23

JAUD1, p.2-22

Back PanelI/O, p.2-10

JPW1, p.2-9

SYS_FAN,p.2-19

JCD1, p.2-20

IDE2/1,p.2-17

CPU, p.2-3

ATX1, p.2-9

JFP1, p.2-21

AGP1, p.2-26

PCI 1~3,p.2-26

JAUX1,p.2-20

JCOM1, p.2-11

JSP1, p.2-20SATA2/1,p.2-18

J1394_1, p.2-24

JMD1, p.2-20

CNR1, p.2-26

Page 15: 865GM3/865PEM2 Seriesmsi-ftp.de/Manuals/6763-englv1.0-865GM3865PEM2Series.pdf · 2009-08-19 · 865GM3/865PEM2 Series. ii Manual Rev: 1.0 Release Date: July 2003 FCC-B Radio Frequency

2-3

Hardware Setup

Central Processing Unit: CPU

CPU Core Speed Derivation Procedure

If CPU Clock = 100MHzCore/Bus ratio = 24

then CPU core speed = Host Clock x Core/Bus ratio= 100MHz x 24= 2.4 GHz

MSI Reminds You...OverheatingOverheating will seriously damage the CPU and system, al-ways make sure the cooling fan can work properly to protectthe CPU from overheating.

Replacing the CPUWhile replacing the CPU, always turn off the ATX power sup-ply or unplug the power supply’s power cord from groundedoutlet first to ensure the safety of CPU.

The mainboard supports Intel® Pentium® 4 processors in the 478 pinpackage. The mainboard uses a CPU socket called PGA478 for easy CPUinstallation. When you are installing the CPU, make sure the CPU has aheat sink and a cooling fan attached on the top to prevent overheating. Ifyou do not find the heat sink and cooling fan, contact your dealer to purchaseand install them before turning on the computer.

Page 16: 865GM3/865PEM2 Seriesmsi-ftp.de/Manuals/6763-englv1.0-865GM3865PEM2Series.pdf · 2009-08-19 · 865GM3/865PEM2 Series. ii Manual Rev: 1.0 Release Date: July 2003 FCC-B Radio Frequency

2-4

MS-6763 M-ATX Mainboard

1. Please turn off the power andunplug the power cord beforeinstalling the CPU.

2. Pull the lever sideways awayfrom the socket. Make sure toraise the lever up to a 90-de-gree angle.

3. Look for the gold arrow. Thegold arrow should point to-wards the lever pivot. TheCPU can only fit in the cor-rect orientation.

4. If the CPU is correctlyinstalled, the pins should becompletely embedded into thesocket and can not be seen.Please note that any violationof the correct installation pro-cedures may cause permanentdamages to your mainboard.

5. Press the CPU down firmlyinto the socket and close thelever. As the CPU is likely tomove while the lever is beingclosed, always close the leverwith your fingers pressingtightly on top of the CPU tomake sure the CPU is prop-erly and completely embed-ded into the socket.

CPU Installation Procedures for Socket 478

Open Lever

90 degreeSliding Plate

Close Lever

Press downthe CPU

Gold arrow

Gold arrow

Gold arrow

Correct CPU placement

Incorrect CPU placement

X

O

Page 17: 865GM3/865PEM2 Seriesmsi-ftp.de/Manuals/6763-englv1.0-865GM3865PEM2Series.pdf · 2009-08-19 · 865GM3/865PEM2 Series. ii Manual Rev: 1.0 Release Date: July 2003 FCC-B Radio Frequency

2-5

Hardware Setup

Installing the CPU FanAs processor technology pushes to faster speeds and higher performance,

thermal management becomes increasingly important. To dissipate heat, youneed to attach the CPU cooling fan and heatsink on top of the CPU. Followthe instructions below to install the Heatsink/Fan:

2. Position the heatsink onto the reten-tion mechanism.

1. Locate the CPU and its retentionmechanism on the motherboard.

3. Mount the fan on top of the heatsink.Press down the fan until its four clipsget wedged in the holes of the reten-tion mechanism.

4. Press the two levers down to fastenthe fan. Each lever can be presseddown in only ONE direction.

retention mechanism

levers

Page 18: 865GM3/865PEM2 Seriesmsi-ftp.de/Manuals/6763-englv1.0-865GM3865PEM2Series.pdf · 2009-08-19 · 865GM3/865PEM2 Series. ii Manual Rev: 1.0 Release Date: July 2003 FCC-B Radio Frequency

2-6

MS-6763 M-ATX Mainboard

5. Connect the fan power cable from the mounted fan to the 3-pin fan power connectoron the board.

fan power cable

NOTES

Page 19: 865GM3/865PEM2 Seriesmsi-ftp.de/Manuals/6763-englv1.0-865GM3865PEM2Series.pdf · 2009-08-19 · 865GM3/865PEM2 Series. ii Manual Rev: 1.0 Release Date: July 2003 FCC-B Radio Frequency

2-7

Hardware Setup

The mainboard provides four 184-pin unbuffered PC3200/PC2700/PC2100 DDR DIMMs and supports the memory size up to 4GB. To operateproperly, at least two DIMM modules must be installed onboard.

Memory

DDR DIMM Slots(DIMM 1~4)

DDR Population RulesInstall at least one DIMM module on the slots. Each DIMM slot supports

up to a maximum size of 1GB. Users can install either single- or double-sidedmodules to meet their own needs. Please note that each DIMM can workrespectively for single-channel DDR, but there are some rules while usingdual-channel DDR (Please refer to the suggested DDR population table on p.2-8). Users may install memory modules of different type and density ondifferent-channel DDR DIMMs. However, the same type and density memorymodules are necessary while using dual-channel DDR, or instability may occur.

Memory Speed/CPU FSB Support Matrix

DDR200 DDR266 DDR333 DDR400

FSB400 V V X X

FSB533 V V V X

FSB800 V V V V

Page 20: 865GM3/865PEM2 Seriesmsi-ftp.de/Manuals/6763-englv1.0-865GM3865PEM2Series.pdf · 2009-08-19 · 865GM3/865PEM2 Series. ii Manual Rev: 1.0 Release Date: July 2003 FCC-B Radio Frequency

2-8

MS-6763 M-ATX Mainboard

Installing DDR Modules1. The DDR DIMM has only one notch on the center of module. The mod-

ule will only fit in the right orientation.2. Insert the DIMM memory module vertically into the DIMM slot. Then

push it in until the golden finger on the memory module is deeply in-serted in the socket.

3. The plastic clip at each side of the DIMM slot will automatically close.

MSI Reminds You...You can barely see the golden finger if the module is properly inserted in the socket.

Volt Notch

Please refer to the following table for detailed dual-channel DDRpopulation rules. Other combination not listed below will function as single-channel DDR.DIMM1 (CH A) DIMM2 (CH A) DIMM3 (CH B) DIMM4 (CH B) System Density128MB~1GB 128MB~1GB 256MB~2GB128MB~1GB 128MB~1GB 256MB~2GB

128MB~1GB 128MB~1GB 256MB~2GB128MB~1GB 128MB~1GB 256MB~2GB

128MB~1GB 128MB~1GB 128MB~1GB 384MB~3GB128MB~1GB 128MB~1GB 128MB~1GB 384MB~3GB128MB~1GB 128MB~1GB 128MB~1GB 384MB~3GB

128MB~1GB 128MB~1GB 128MB~1GB 384MB~3GB128MB~1GB 128MB~1GB 128MB~1GB 128MB~1GB 512MB~4GB

Page 21: 865GM3/865PEM2 Seriesmsi-ftp.de/Manuals/6763-englv1.0-865GM3865PEM2Series.pdf · 2009-08-19 · 865GM3/865PEM2 Series. ii Manual Rev: 1.0 Release Date: July 2003 FCC-B Radio Frequency

2-9

Hardware Setup

PIN SIGNAL

1 GND2 GND3 12V4 12V

JPW1 Pin Definition

Power SupplyThe mainboard supports ATX power supply for the power system. Be-

fore inserting the power supply connector, always make sure that all compo-nents are installed properly to ensure that no damage will be caused.

ATX 20-Pin Power Connector: ATX1This connector allows you to connect to an ATX power supply. To

connect to the ATX power supply, make sure the plug of the power supply isinserted in the proper orientation and the pins are aligned. Then push downthe power supply firmly into the connector.

ATX 12V Power Connector: JPW1This 12V power connector is used to provide power to the CPU.

PIN SIGNAL

11 3.3V12 -12V13 GND14 PS_ON15 GND16 GND17 GND18 -5V19 5V20 5V

PIN SIGNAL

1 3.3V2 3.3V3 GND4 5V5 GND6 5V7 GND8 PW_OK9 5V_SB10 12V

ATX1 Pin Definition

1

3

JPW1

2

4

ATX1

10

1

20

11

Page 22: 865GM3/865PEM2 Seriesmsi-ftp.de/Manuals/6763-englv1.0-865GM3865PEM2Series.pdf · 2009-08-19 · 865GM3/865PEM2 Series. ii Manual Rev: 1.0 Release Date: July 2003 FCC-B Radio Frequency

2-10

MS-6763 M-ATX Mainboard

The back panel provides the following connectors:

Back Panel

Mouse/Keyboard ConnectorThe mainboard provides a standard PS/2® mouse/keyboard mini DIN

connector for attaching a PS/2® mouse/keyboard. You can plug a PS/2® mouse/keyboard directly into this connector. The connector location and pin assign-ments are as follows:

PS/2 Mouse/Keyboard(6-pin Female)

2 1

34

56 PIN SIGNAL DESCRIPTION

1 Mouse/Keyboard Data Mouse/Keyboard data2 NC No connection3 GND Ground4 VCC +5V5 Mouse/Keyboard Clock Mouse/Keyboard clock6 NC No connection

Pin Definition

MouseParallel

USB Ports USB PortsKeyboardMic-InL-Out

L-InLAN(Optional)

COM A VGA Port(for 865GM3)

1394 Port(for 865PEM2)

Page 23: 865GM3/865PEM2 Seriesmsi-ftp.de/Manuals/6763-englv1.0-865GM3865PEM2Series.pdf · 2009-08-19 · 865GM3/865PEM2 Series. ii Manual Rev: 1.0 Release Date: July 2003 FCC-B Radio Frequency

2-11

Hardware Setup

Serial Port Connectors: COMA & JCOM1The mainboard offers two 9-pin serial ports COMA and JCOM1. All

ports are 16550A high speed communication ports that send/receive 16 bytesFIFOs. You can attach a serial mouse or other serial device directly to them.

COMA

1 2 3 4 5

6 7 8 9

VGA Connector (for 865GM3 Series only)The mainboard provides a DB 15-pin female connector to connect a

VGA monitor.

Pin Signal Description 1 RED 2 GREEN 3 BLUE 4 N/C 5 GND 6 GND 7 GND 8 GND 9 +5V 10 GND 11 N/C 12 SDA 13 Horizontal Sync 14 Vertical Sync 15 SCL

VGA Connector(DB 15-pin)

15

1115

PIN SIGNAL DESCRIPTION

1 DCD Data Carry Detect2 SIN Serial In or Receive Data3 SOUT Serial Out or Transmit Data4 DTR Data Terminal Ready5 GND Ground6 DSR Data Set Ready7 RTS Request To Send8 CTS Clear To Send9 RI Ring Indicate

Pin Definition

JCOM1

1 2

9

Page 24: 865GM3/865PEM2 Seriesmsi-ftp.de/Manuals/6763-englv1.0-865GM3865PEM2Series.pdf · 2009-08-19 · 865GM3/865PEM2 Series. ii Manual Rev: 1.0 Release Date: July 2003 FCC-B Radio Frequency

2-12

MS-6763 M-ATX Mainboard

Parallel Port Connector: LPT1The mainboard provides a 25-pin female centronic connector as LPT.

A parallel port is a standard printer port that supports Enhanced Parallel Port(EPP) and Extended Capabilities Parallel Port (ECP) mode.

13 1

1425

PIN SIGNAL DESCRIPTION1 STROBE Strobe2 DATA0 Data03 DATA1 Data14 DATA2 Data25 DATA3 Data36 DATA4 Data47 DATA5 Data58 DATA6 Data69 DATA7 Data710 ACK# Acknowledge11 BUSY Busy12 PE Paper End13 SELECT Select14 AUTO FEED# Automatic Feed15 ERR# Error16 INIT# Initialize Printer17 SLIN# Select In18 GND Ground19 GND Ground20 GND Ground21 GND Ground22 GND Ground23 GND Ground24 GND Ground25 GND Ground

Pin Definition

Page 25: 865GM3/865PEM2 Seriesmsi-ftp.de/Manuals/6763-englv1.0-865GM3865PEM2Series.pdf · 2009-08-19 · 865GM3/865PEM2 Series. ii Manual Rev: 1.0 Release Date: July 2003 FCC-B Radio Frequency

2-13

Hardware Setup

LAN Jack: 10/100Mbps LAN (for 865PEM2 Series) or Giga-bit LAN (for 865GM3 Series)

The mainboard provides one standard RJ-45 jack for connection to Lo-cal Area Network (LAN). Two LAN chipsets are available upon request:

1. 10/100Mbps LAN for 865PEM2-IL mainboard.2. Gigabit LAN for 865GM3-F mainboard.

Gigabit LAN enables data to be transferred at 1000, 100 or 10Mbps. 10/100 LAN enables data to be transferred at 100 or 10Mbps. You can connect anetwork cable to this LAN jack.

RJ-45 LAN Jack

10/100 LAN Pin Definition

PIN SIGNAL DESCRIPTION

1 TDP Transmit Differential Pair

2 TDN Transmit Differential Pair

3 RDP Receive Differential Pair

4 NC Not Used

5 NC Not Used

6 RDN Receive Differential Pair

7 NC Not Used

8 NC Not Used

Gigabit LAN Pin Definition

PIN SIGNAL DESCRIPTION

1 D0P Differential Pair 0+

2 D0N Differential Pair 0-

3 D1P Differential Pair 1+

4 D2P Differential Pair 2+

5 D2N Differential Pair 2-

6 D1N Differential Pair 1-

7 D3P Differential Pair 3+

8 D3N Differential Pair 3-

Page 26: 865GM3/865PEM2 Seriesmsi-ftp.de/Manuals/6763-englv1.0-865GM3865PEM2Series.pdf · 2009-08-19 · 865GM3/865PEM2 Series. ii Manual Rev: 1.0 Release Date: July 2003 FCC-B Radio Frequency

2-14

MS-6763 M-ATX Mainboard

USB ConnectorsThe mainboard provides a UHCI (Universal Host Controller Interface)

Universal Serial Bus root for attaching USB devices such as keyboard, mouseor other USB-compatible devices. You can plug the USB device directly intothe connector.

USB Ports

1 2 3 4

5 6 7 8

PIN SIGNAL DESCRIPTION

1 VCC +5V2 -Data 0 Negative Data Channel 03 +Data0 Positive Data Channel 04 GND Ground5 VCC +5V6 -Data 1 Negative Data Channel 17 +Data 1 Positive Data Channel 18 GND Ground

USB Port Description

IEEE1394 Port (Optional for 865PEM2 Series only)The back panel provides one standard IEEE 1394 port. The standard

IEEE1394 port connects to IEEE1394 devices without external power. TheIEEE1394 high-speed serial bus complements USB by providing enhancedPC connectivity for a wide range of devices, including consumer electronicsaudio/video (A/V) appliances, storage peripherals, other PCs, and portabledevices.

IEEE1394 Port

Page 27: 865GM3/865PEM2 Seriesmsi-ftp.de/Manuals/6763-englv1.0-865GM3865PEM2Series.pdf · 2009-08-19 · 865GM3/865PEM2 Series. ii Manual Rev: 1.0 Release Date: July 2003 FCC-B Radio Frequency

2-15

Hardware Setup

Audio Port ConnectorsLine Out is a connector for Speakers or Headphones. Line In is used

for external CD player, Tape player, or other audio devices. Mic is a connec-tor for microphones.

1/8” Stereo Audio Connectors

Mic In

Line Out

Line In

Page 28: 865GM3/865PEM2 Seriesmsi-ftp.de/Manuals/6763-englv1.0-865GM3865PEM2Series.pdf · 2009-08-19 · 865GM3/865PEM2 Series. ii Manual Rev: 1.0 Release Date: July 2003 FCC-B Radio Frequency

2-16

MS-6763 M-ATX Mainboard

The mainboard provides connectors to connect to FDD, IDE HDD, case,audio, LAN, USB Ports, and CPU/System fans.

Floppy Disk Drive Connector: FDD1The mainboard provides a standard floppy disk drive connector that

supports 360K, 720K, 1.2M, 1.44M and 2.88M floppy disk types.

Connectors

FDD1

Chassis Intrusion Switch Connector: JCI1 (Optional)This connector is connected to 2-pin connector chassis switch. If the

chassis is open, the switch will be short. The system will record this status. Toclear the warning, you must enter the BIOS setting and clear the status.

JCI1

CINTRUGND

1

Page 29: 865GM3/865PEM2 Seriesmsi-ftp.de/Manuals/6763-englv1.0-865GM3865PEM2Series.pdf · 2009-08-19 · 865GM3/865PEM2 Series. ii Manual Rev: 1.0 Release Date: July 2003 FCC-B Radio Frequency

2-17

Hardware Setup

MSI Reminds You...If you install two hard disks on cable, you must configure thesecond drive to Slave mode by setting its jumper. Refer to thehard disk documentation supplied by hard disk vendors forjumper setting instructions.

Ultra ATA HDD Connectors: IDE1, IDE2The mainboard has a 32-bit Enhanced PCI IDE and Ultra DMA 33/66/

100 controller that provides PIO mode 0~4, Bus Master, and Ultra DMA 33/66/100 function. You can connect up to four hard disk drives, CD-ROM,120MB Floppy (reserved for future BIOS) and other devices. These connec-tors support the provided IDE hard disk cable.

IDE1 (Primary IDE Connector)The first hard drive should always be connected to IDE1. IDE1 canconnect a Master and a Slave drive. You must configure second harddrive to Slave mode by setting the jumper accordingly.

IDE2 (Secondary IDE Connector)IDE2 can also connect a Master and a Slave drive.

IDE1IDE2

Page 30: 865GM3/865PEM2 Seriesmsi-ftp.de/Manuals/6763-englv1.0-865GM3865PEM2Series.pdf · 2009-08-19 · 865GM3/865PEM2 Series. ii Manual Rev: 1.0 Release Date: July 2003 FCC-B Radio Frequency

2-18

MS-6763 M-ATX Mainboard

Serial ATA HDD Connectors: SATA1, SATA2The mainboard provides dual high-speed Serial ATA interface ports.

The ports support 1st generation Serial ATA data rates of 150MB/s and arefully compliant with Serial ATA 1.0 specifications. Each Serial ATA connec-tor can connect to 1 hard disk drive.

PIN SIGNAL PIN SIGNAL

1 GND 2 TXP3 TXN 4 GND5 RXN 6 RXP7 GND

Pin Definition

Connect to SATA1 or SATA2

Take out the dust cover andconnect to the hard disk devices

Optional Serial ATA cable

SATA2

SATA1

17

MSI Reminds You...Please do not fold the Serial ATA cable into 90-degree angle.Otherwise, the loss of data may occur during transmission.

Page 31: 865GM3/865PEM2 Seriesmsi-ftp.de/Manuals/6763-englv1.0-865GM3865PEM2Series.pdf · 2009-08-19 · 865GM3/865PEM2 Series. ii Manual Rev: 1.0 Release Date: July 2003 FCC-B Radio Frequency

2-19

Hardware Setup

MSI Reminds You... Always consult the vendors for proper CPU cooling fan.

CPU_FANSensor+12VGND

Fan Power Connectors: CPU_FAN/SYS_FANThe CPU_FAN (processor fan) and SYS_FAN (system fan) support sys-

tem cooling fan with +12V. It supports three-pin head connector. When con-necting the wire to the connectors, always take note that the red wire is thepositive and should be connected to the +12V, the black wire is Ground andshould be connected to GND.

SYS_FANSENSOR+12VGND

Page 32: 865GM3/865PEM2 Seriesmsi-ftp.de/Manuals/6763-englv1.0-865GM3865PEM2Series.pdf · 2009-08-19 · 865GM3/865PEM2 Series. ii Manual Rev: 1.0 Release Date: July 2003 FCC-B Radio Frequency

2-20

MS-6763 M-ATX Mainboard

Connected to JSP1

SPDIF Bracket (Optional)

CD-In Connector: JCD1The connector is for CD-ROM audio connector.

Modem-In Connector: JMD1 (Optional)The connector is for modem with internal audio connector.

Aux Line-In Connector: JAUX1 (Optional)The connector is for DVD add-on card with Line-in connector.

SPDIF-Out Connector: JSP1 (Optional)This connector is used to connect SPDIF (Sony & Philips Digital Inter-

connect Format) interface for digital audio transmission.

JCD1

GNDR L

JAUX1

GNDR L

JSP1

VCC

SPDIF

GND

Phone_InMono_Out

JMD1

GND

Page 33: 865GM3/865PEM2 Seriesmsi-ftp.de/Manuals/6763-englv1.0-865GM3865PEM2Series.pdf · 2009-08-19 · 865GM3/865PEM2 Series. ii Manual Rev: 1.0 Release Date: July 2003 FCC-B Radio Frequency

2-21

Hardware Setup

PIN SIGNAL DESCRIPTION

1 HD_LED_P Hard disk LED pull-up2 FP PWR/SLP MSG LED pull-up3 HD_LED_N Hard disk active LED4 FP PWR/SLP MSG LED pull-up5 RST_SW_N Reset Switch low reference pull-down to GND6 PWR_SW_P Power Switch high reference pull-up7 RST_SW_P Reset Switch high reference pull-up8 PWR_SW_N Power Switch low reference pull-down to GND9 RSVD_DNU Reserved. Do not use.

JFP1 Pin Definition

Front Panel Connectors: JFP1The mainboard provides one front panel connector for electrical con-

nection to the front panel switches and LEDs. The JFP1 is compliant withIntel® Front Panel I/O Connectivity Design Guide.

12

910

JFP1

HDDLED

ResetSwitch

PowerLED

PowerSwitch

Page 34: 865GM3/865PEM2 Seriesmsi-ftp.de/Manuals/6763-englv1.0-865GM3865PEM2Series.pdf · 2009-08-19 · 865GM3/865PEM2 Series. ii Manual Rev: 1.0 Release Date: July 2003 FCC-B Radio Frequency

2-22

MS-6763 M-ATX Mainboard

Front Panel Audio Connector: JAUD1The JAUD1 front panel audio connector allows you to connect to the

front panel audio and is compliant with Intel® Front Panel I/O ConnectivityDesign Guide.

MSI Reminds You...If you don’t want to connect to the front audioheader, pins 5 & 6, 9 & 10 have to be jumpered inorder to have signal output directed to the rearaudio ports. Otherwise, the Line-Out connector onthe back panel will not function.

PIN SIGNAL DESCRIPTION

1 AUD_MIC Front panel microphone input signal2 AUD_GND Ground used by analog audio circuits3 AUD_MIC_BIAS Microphone power4 AUD_VCC Filtered +5V used by analog audio circuits5 AUD_FPOUT_R Right channel audio signal to front panel6 AUD_RET_R Right channel audio signal return from front panel7 NC No connection8 KEY No pin9 AUD_FPOUT_L Left channel audio signal to front panel10 AUD_RET_L Left channel audio signal return from front panel

Pin Definition

JAUD112

910

5

610

9

Page 35: 865GM3/865PEM2 Seriesmsi-ftp.de/Manuals/6763-englv1.0-865GM3865PEM2Series.pdf · 2009-08-19 · 865GM3/865PEM2 Series. ii Manual Rev: 1.0 Release Date: July 2003 FCC-B Radio Frequency

2-23

Hardware Setup

Front USB Connectors: JUSB1, JUSB2The mainboard provides two USB 2.0 pin headers JUSB1/2 that are

compliant with Intel® I/O Connectivity Design Guide. USB 2.0 technologyincreases data transfer rate up to a maximum throughput of 480Mbps, whichis 40 times faster than USB 1.1, and is ideal for connecting high-speed USBinterface peripherals such as USB HDD, digital cameras, MP3 players,printers, modems and the like.

PIN SIGNAL PIN SIGNAL

1 VCC 2 VCC

3 USB0- 4 USB1-

5 USB0+ 6 USB1+

7 GND 8 GND

9 Key 10 USBOC

Pin Definition

Connected to JUSB1or JUSB2

USB 2.0 Bracket(Optional)

1 9 2 10

JUSB1/2

Page 36: 865GM3/865PEM2 Seriesmsi-ftp.de/Manuals/6763-englv1.0-865GM3865PEM2Series.pdf · 2009-08-19 · 865GM3/865PEM2 Series. ii Manual Rev: 1.0 Release Date: July 2003 FCC-B Radio Frequency

2-24

MS-6763 M-ATX Mainboard

IEEE 1394 Connector: J1394_1 (Optional for 865PEM2 Series)The mainboard provides one 1394 pin header that allows you to connect

IEEE 1394 ports via an external IEEE1394 bracket (optional).

Pin Definition

PIN SIGNAL PIN SIGNAL

1 TPA+ 2 TPA-

3 Ground 4 Ground

5 TPB+ 6 TPB-

7 Cable power 8 Cable power

9 Key (no pin) 10 Ground

IEEE1394 Bracket (Optional)

FoolproofDesign

J1394_1

1 9 2 10

Page 37: 865GM3/865PEM2 Seriesmsi-ftp.de/Manuals/6763-englv1.0-865GM3865PEM2Series.pdf · 2009-08-19 · 865GM3/865PEM2 Series. ii Manual Rev: 1.0 Release Date: July 2003 FCC-B Radio Frequency

2-25

Hardware Setup

The motherboard provides the following jumpers for you to set thecomputer’s function. This section will explain how to change yourmotherboard’s function through the use of jumpers.

Clear CMOS Jumper: JBAT1There is a CMOS RAM on board that has a power supply from external

battery to keep the data of system configuration. With the CMOS RAM, thesystem can automatically boot OS every time it is turned on. If you want toclear the system configuration, use the JBAT1 (Clear CMOS Jumper ) to cleardata.

Jumpers

MSI Reminds You...You can clear CMOS by shorting 2-3 pin while the system is off.Then return to 1-2 pin position. Avoid clearing the CMOS whilethe system is on; it will damage the mainboard.

JBAT1

1

Clear Data

1

3

Keep Data

1

3

Page 38: 865GM3/865PEM2 Seriesmsi-ftp.de/Manuals/6763-englv1.0-865GM3865PEM2Series.pdf · 2009-08-19 · 865GM3/865PEM2 Series. ii Manual Rev: 1.0 Release Date: July 2003 FCC-B Radio Frequency

2-26

MS-6763 M-ATX Mainboard

Slots

PCI Slots

AGP (Accelerated Graphics Port) SlotThe AGP slot allows you to insert the AGP graphics card. AGP is an

interface specification designed for the throughput demands of 3D graphics.It introduces a 66MHz, 32-bit channel for the graphics controller to directlyaccess main memory. The slot supports 8x/4x cards at 0.8V (AGP 3.0) or 4xcards at 1.5V (3.3V not supported).

PCI (Peripheral Component Interconnect) SlotsThe PCI slots allow you to insert the expansion cards to meet your needs.

When adding or removing expansion cards, make sure that you unplug thepower supply first. Meanwhile, read the documentation for the expansion cardto make any necessary hardware or software settings for the expansion card,such as jumpers, switches or BIOS configuration.

CNR (Communication Network Riser) SlotThe CNR slot allows you to insert the CNR expansion cards. CNR is a

specially designed network, audio, or modem riser card for ATX familymotherboards. Its main processing is done through software and controlledby the motherboard’s chipset.

AGP Slot

The motherboard provides one AGP slot, three 32-bit PCI bus slots, andone CNR slot.

CNR Slot

Page 39: 865GM3/865PEM2 Seriesmsi-ftp.de/Manuals/6763-englv1.0-865GM3865PEM2Series.pdf · 2009-08-19 · 865GM3/865PEM2 Series. ii Manual Rev: 1.0 Release Date: July 2003 FCC-B Radio Frequency

2-27

Hardware Setup

PCI Interrupt Request RoutingThe IRQ, acronym of interrupt request line and pronounced I-R-Q, are

hardware lines over which devices can send interrupt signals to themicroprocessor. The PCI IRQ pins are typically connected to the PCI bus INTA# ~ INT D# pins as follows:

Order 1 Order 2 Order 3 Order 4

PCI Slot 1 INT A# INT B# INT C# INT D#

PCI Slot 2 INT B# INT C# INT D# INT A#

PCI Slot 3 INT C# INT D# INT A# INT B#

Page 40: 865GM3/865PEM2 Seriesmsi-ftp.de/Manuals/6763-englv1.0-865GM3865PEM2Series.pdf · 2009-08-19 · 865GM3/865PEM2 Series. ii Manual Rev: 1.0 Release Date: July 2003 FCC-B Radio Frequency

3-1

BIOS Setup

Chapter 3. BIOS Setup

This chapter provides information on the BIOS Setup pro-gram and allows you to configure the system for optimum use.You may need to run the Setup program when:

An error message appears on the screen during the systembooting up, and requests you to run SETUP.

You want to change the default settings for customizedfeatures.

BIOS Setup

Page 41: 865GM3/865PEM2 Seriesmsi-ftp.de/Manuals/6763-englv1.0-865GM3865PEM2Series.pdf · 2009-08-19 · 865GM3/865PEM2 Series. ii Manual Rev: 1.0 Release Date: July 2003 FCC-B Radio Frequency

3-2

MS-6763 M-ATX Mainboard

Entering Setup

Control Keys

Power on the computer and the system will start POST (Power On SelfTest) process. When the message below appears on the screen, press <DEL>key to enter Setup.

Press DEL to enter SETUP

If the message disappears before you respond and you still wish to enterSetup, restart the system by turning it OFF and On or pressing the RESETbutton. You may also restart the system by simultaneously pressing <Ctrl>,<Alt>, and <Delete> keys.

<↑> Move to the previous item<↓> Move to the next item<←> Move to the item in the left hand<→> Move to the item in the right hand<Enter> Select the item<Esc> Jumps to the Exit menu or returns to the main menu from a submenu<+/PU> Increase the numeric value or make changes<-/PD> Decrease the numeric value or make changes<F1> General help, only for Status Page Setup Menu and Option

Page Setup Menu<F5> Restore the previous CMOS value from CMOS, only for Option

Page Setup Menu<F10> Save all the CMOS changes and exit

Page 42: 865GM3/865PEM2 Seriesmsi-ftp.de/Manuals/6763-englv1.0-865GM3865PEM2Series.pdf · 2009-08-19 · 865GM3/865PEM2 Series. ii Manual Rev: 1.0 Release Date: July 2003 FCC-B Radio Frequency

3-3

BIOS Setup

Getting HelpAfter entering the Setup menu, the first menu you will see is the Main

Menu.

Main MenuThe main menu lists the setup functions you can make changes to. You

can use the arrow keys ( ↑↓ ) to select the item. The on-line description of thehighlighted setup function is displayed at the bottom of the screen.

Sub-MenuIf you find a right pointer symbol (as shown in the right view) appears

to the left of certain fields that means asub-menu can be launched from this field.A sub-menu contains additional optionsfor a field parameter. You can use arrowkeys ( ↑↓ ) to highlight the field and press<Enter> to call up the sub-menu. Then you can use the control keys to entervalues and move from field to field within a sub-menu. If you want to returnto the main menu, just press the <Esc >.

General Help <F1>The BIOS setup program provides a General Help screen. You can call

up this screen from any menu by simply pressing <F1>. The Help screen liststhe appropriate keys to use and the possible selections for the highlighteditem. Press <Esc> to exit the Help screen.

MSI Reminds You...The items under each BIOS category described in this chapterare under continuous update for better system performance.Therefore, the description may be slightly different from the lat-est BIOS and should be held for reference only.

Page 43: 865GM3/865PEM2 Seriesmsi-ftp.de/Manuals/6763-englv1.0-865GM3865PEM2Series.pdf · 2009-08-19 · 865GM3/865PEM2 Series. ii Manual Rev: 1.0 Release Date: July 2003 FCC-B Radio Frequency

3-4

MS-6763 M-ATX Mainboard

The Main Menu

Standard CMOS FeaturesUse this menu for basic system configurations, such as time, date etc.

Advanced BIOS FeaturesUse this menu to configure the special enhanced features.

Advanced Chipset FeaturesUse this menu to change the values in the chipset registers and optimize yoursystem’s performance.

Integrated PeripheralsUse this menu to specify your settings for integrated peripherals.

Power Management SetupUse this menu to specify your settings for power management.

Once you enter Award BIOS CMOS Setup Utility, the Main Menu willappear on the screen. The Main Menu displays twelve configurable functionsand two exit choices. Use arrow keys to move among the items and press<Enter> to enter the sub-menu.

Page 44: 865GM3/865PEM2 Seriesmsi-ftp.de/Manuals/6763-englv1.0-865GM3865PEM2Series.pdf · 2009-08-19 · 865GM3/865PEM2 Series. ii Manual Rev: 1.0 Release Date: July 2003 FCC-B Radio Frequency

3-5

BIOS Setup

PNP/PCI ConfigurationsThis entry appears if your system supports PnP/PCI.

PC Health StatusThis menu shows the status of your CPU, fan, overall system status, etc. Moni-tor function is available only if there is hardware monitoring mechanismonboard.

Frequency/Voltage ControlUse this menu to specify your settings for frequency/voltage control.

Load Default SettingUse this menu to load the BIOS default values that are factory settings foroptimal system operations.

Set Supervisor/User PasswordUse this menu to set user and supervisor passwords.

Save & Exit SetupSave changes to CMOS and exit setup.

Exit Without SavingAbandon all changes and exit setup.

Page 45: 865GM3/865PEM2 Seriesmsi-ftp.de/Manuals/6763-englv1.0-865GM3865PEM2Series.pdf · 2009-08-19 · 865GM3/865PEM2 Series. ii Manual Rev: 1.0 Release Date: July 2003 FCC-B Radio Frequency

3-6

MS-6763 M-ATX Mainboard

Standard CMOS FeaturesThe items inside Standard CMOS Features menu are divided into 10

categories. Each category includes none, one or more setup items. Use thearrow keys to highlight the item you want to modify and use the <PgUp> or<PgDn> keys to switch to the value you prefer.

Date (mm:dd:yy)This allows you to set the system to the date that you want (usually the currentdate). The format is <day><month> <date> <year>.

day Day of the week, from Sun to Sat, determined byBIOS. Read-only.

month The month from Jan. through Dec.date The date from 1 to 31 can be keyed by numeric

function keys.year The year can be adjusted by users.

Time (hh:mm:ss)This allows you to set the system time that you want (usually the currenttime). The time format is <hour> <minute> <second>.

IDE Channel 0/1 Master/SlavePress PgUp/<+> or PgDn/<-> to select Manual, None, Auto type. Note thatthe specifications of your drive must match with the drive table. The hard disk

Page 46: 865GM3/865PEM2 Seriesmsi-ftp.de/Manuals/6763-englv1.0-865GM3865PEM2Series.pdf · 2009-08-19 · 865GM3/865PEM2 Series. ii Manual Rev: 1.0 Release Date: July 2003 FCC-B Radio Frequency

3-7

BIOS Setup

will not work properly if you enter improper information for this category. Ifyour hard disk drive type is not matched or listed, you can use Manual todefine your own drive type manually.If you select Manual, related information is asked to be entered to the follow-ing items. Enter the information directly from the keyboard. This informationshould be provided in the documentation from your hard disk vendor or thesystem manufacturer.If the controller of HDD interface is SCSI, the selection shall be “None”. Ifthe controller of HDD interface is CD-ROM, the selection shall be “None”.

Access Mode The settings are CHS, LBA, Large, Auto.Capacity The formatted size of the storage device.Cylinder Number of cylinders.Head Number of heads.Precomp Write precompensation.Landing Zone Cylinder location of the landing zone.Sector Number of sectors.

Drive A/BThis item allows you to set the type of floppy drives installed. Availableoptions are None, 360K, 5.25 in., 1.2M, 5.25 in., 720K, 3.5 in., 1.44M, 3.5 in.,2.88M, 3.5 in.

VideoThe setting controls the type of video adapter used for the primary monitor ofthe system. Available options are EGA/VGA , CGA 40, CGA 80 and Mono.

Halt OnThe setting determines whether the system will stop if an error is detected atboot. Available options are:

All Errors The system stops when any error is detected.No Errors The system doesn’t stop for any detected error.All, But Keyboard The system doesn’t stop for a keyboard error.All, But Diskette The system doesn’t stop for a disk error.All, But Disk/Key The system doesn’t stop for either a disk or a key-

board error.

Page 47: 865GM3/865PEM2 Seriesmsi-ftp.de/Manuals/6763-englv1.0-865GM3865PEM2Series.pdf · 2009-08-19 · 865GM3/865PEM2 Series. ii Manual Rev: 1.0 Release Date: July 2003 FCC-B Radio Frequency

3-8

MS-6763 M-ATX Mainboard

Advanced BIOS Features

Hard Disk Boot PriorityThis setting determines the boot priority of the installed hard disk drives.

Virus WarningThe item is to set the Virus Warning feature for IDE Hard Disk boot sectorprotection. If the function is enabled and any attempt to write data into thisarea is made, BIOS will display a warning message on screen and beep. Set-ting options: Disabled, Enabled.

CPU L1 & L2 CacheCache memory is additional memory that is much faster than conventionalDRAM (system memory). When the CPU requests data, the system transfersthe requested data from the main DRAM into cache memory, for even fasteraccess by the CPU. The settings enable/disable the internal cache (also knownas L1 or level 1 cache) and external cache (also known as L2 or level 2 cache).Setting options: Disabled, Enabled.

HT CPU FunctionWith Intel® Hyper-Threading Technology, a single Hyper-Threading-enabledprocessor can simultaneously process two threads of code, improving the per-formance of multi-threaded code running on a single processor platform. Set-ting this function to Enabled will improve overall system performance, in-

Page 48: 865GM3/865PEM2 Seriesmsi-ftp.de/Manuals/6763-englv1.0-865GM3865PEM2Series.pdf · 2009-08-19 · 865GM3/865PEM2 Series. ii Manual Rev: 1.0 Release Date: July 2003 FCC-B Radio Frequency

3-9

BIOS Setup

crease number of users a platform can support, improve reaction and responsetime, and increase number of transaction that can be executed. Setting options:Enabled, Disabled.

Quick BootThe setting allows the system to skip certain tests while booting. This willdecrease the time needed to boot the system. Setting options: Enabled,Disabled.

Full Screen Logo ShowThis item enables you to show the company logo on the bootup screen. Set-tings are:

Disabled Shows the POST messages at boot.Enabled Shows a still image (logo) on the full screen at boot.

First/Second/Third Boot DeviceThese settings allow you to set the sequence of boot devices where BIOSattempts to load the disk operating system. Setting options:

Floppy The system will boot from floppy drive.LS120 The system will boot from LS-120 drive.Hard Disk The system will boot from the HDD.CDROM The system will boot from the CD-ROM.ZIP The system will boot from ATAPI ZIP drive.USB-FDD The system will boot from the floppy drive at USB ports.USB-ZIP The system will boot from the ZIP drive at USB ports.USB-CDROM The system will boot from the CD-ROM at USB ports.

MSI Reminds You...Enabling the functionality of Hyper-Threading Technology foryour computer system requires ALL of the following platformComponents:*CPU: An Intel® Pentium® 4 Processor with HT Technology;*Chipset: An Intel® Chipset that supports HT Technology;*BIOS: A BIOS that supports HT Technology and has it enabled;and*OS: An operating system that supports HT Technology.For more information on Hyper-threading Technology, go to:

http://www.intel.com/info/hyperthreading

Page 49: 865GM3/865PEM2 Seriesmsi-ftp.de/Manuals/6763-englv1.0-865GM3865PEM2Series.pdf · 2009-08-19 · 865GM3/865PEM2 Series. ii Manual Rev: 1.0 Release Date: July 2003 FCC-B Radio Frequency

3-10

MS-6763 M-ATX Mainboard

USB-HDD The system will boot from the HDD at USB ports.LAN The system will boot from the Network drive.Disabled Disable this sequence.

Boot Other DeviceSetting the option to Enabled allows the system to try to boot from otherdevices if the system fails to boot from the 1st/2nd/3rd boot device.

Swap Floppy DriveSetting to Enabled will swap floppy drives A: and B:.

Boot Up Floppy SeekSetting to Enabled will make BIOS seek floppy drive A: before booting thesystem. Setting options: Disabled, Enabled.

Boot Up NumLock StatusThis setting is to set the Num Lock status when the system is powered on.Setting to On will turn on the Num Lock key when the system is powered on.Setting to Off will allow users to use the arrow keys on the numeric keypad.Setting options: On, Off.

Gate A20 OptionThis item is to set the Gate A20 status. A20 refers to the first 64KB of ex-tended memory. When the default value Fast is selected, the Gate A20 iscontrolled by Port92 or chipset specific method resulting in faster systemperformance. When Normal is selected, A20 is controlled by a keyboard con-troller or chipset hardware.

Typematic Rate SettingThis item is used to enable or disable the typematic rate setting includingTypematic Rate & Typematic Delay.

Typematic Rate (Chars/Sec)After Typematic Rate Setting is enabled, this item allows you to set the rate(characters/second) at which the keys are accelerated. Settings: 6, 8, 10, 12,15, 20, 24 and 30.

Typematic Delay (Msec)This item allows you to select the delay between when the key was first pressedand when the acceleration begins. Settings: 250, 500, 750 and 1000.

Page 50: 865GM3/865PEM2 Seriesmsi-ftp.de/Manuals/6763-englv1.0-865GM3865PEM2Series.pdf · 2009-08-19 · 865GM3/865PEM2 Series. ii Manual Rev: 1.0 Release Date: July 2003 FCC-B Radio Frequency

3-11

BIOS Setup

Security OptionThis specifies the type of BIOS password protection that is implemented. Set-tings are described below:

APIC ModeThis field is used to enable or disable the APIC (Advanced ProgrammableInterrupt Controller). Due to compliance with PC2001 design guide, the sys-tem is able to run in APIC mode. Enabling APIC mode will expand availableIRQ resources for the system. Settings: Enabled and Disabled.

MPS Version Control for OSThis field allows you to select which MPS (Multi-Processor Specification)version to be used for the operating system. You need to select the MPS ver-sion supported by your operating system. To find out which version to use,consult the vendor of your operating system. Settings: 1.4, 1.1.

OS Select For DRAM > 64MBThis allows you to run the OS/2® operating system with DRAM greater than64MB. Setting options: OS2, Non-OS2.

HDD S.M.A.R.T. CapabilityThis allows you to activate the S.M.A.R.T. (Self-Monitoring Analysis & Re-porting Technology) capability for the hard disks. S.M.A.R.T is a utility thatmonitors your disk status to predict hard disk failure. This gives you an op-portunity to move data from a hard disk that is going to fail to a safe placebefore the hard disk becomes offline. Settings: Enabled, Disabled.

Report No FDD For WIN95For compatibility with Windows 95 logo certification, select Yes to releaseIRQ6 when the system contains no floppy drive. When this setting is set toYes, users have to select Disabled for the Onboard FDC Controller in theIntegrated Peripherals menu. Setting options: No, Yes.

Option DescriptionSetup The password prompt appears only when end users try to

run Setup.

System A password prompt appears every time when the com-puter is powered on or when end users try to run Setup.

Page 51: 865GM3/865PEM2 Seriesmsi-ftp.de/Manuals/6763-englv1.0-865GM3865PEM2Series.pdf · 2009-08-19 · 865GM3/865PEM2 Series. ii Manual Rev: 1.0 Release Date: July 2003 FCC-B Radio Frequency

3-12

MS-6763 M-ATX Mainboard

Advanced Chipset Features

MSI Reminds You...Change these settings only if you are familiar with the chipset.

DRAM Timing SelectableSelects whether DRAM timing is controlled by the SPD (Serial PresenceDetect) EEPROM on the DRAM module. Setting to By SPD enables DRAMtimings to be determined by BIOS based on the configurations on the SPD.Selecting Manual allows users to configure the DRAM timings manually.

CAS Latency TimeThis controls the timing delay (in clock cycles) before SDRAM starts a readcommand after receiving it. Settings: 2, 2.5, 3 (clocks). 2 (clocks) increasesthe system performance the most while 3 (clocks) provides the most stableperformance.

Active to Precharge DelayThe field specifies the idle cycles before precharging an idle bank. Settings: 8,7, 6, 5 (clocks).

DRAM RAS# to CAS# DelayThis field allows you to set the number of cycles for a timing delay between

Page 52: 865GM3/865PEM2 Seriesmsi-ftp.de/Manuals/6763-englv1.0-865GM3865PEM2Series.pdf · 2009-08-19 · 865GM3/865PEM2 Series. ii Manual Rev: 1.0 Release Date: July 2003 FCC-B Radio Frequency

3-13

BIOS Setup

the CAS and RAS strobe signals, used when DRAM is written to, read fromor refreshed. Fast speed offers faster performance while slow speed offersmore stable performance. Settings: 4, 3, 2 (clocks).

DRAM RAS# PrechargeThis item controls the number of cycles for Row Address Strobe (RAS) to beallowed to precharge. If insufficient time is allowed for the RAS to accumu-late its charge before DRAM refresh, refresh may be incomplete and DRAMmay fail to retain data. This item applies only when synchronous DRAM isinstalled in the system. Available settings: 4, 3, 2 (clocks).

Memory Frequency ForUse this item to configure the clock frequency of the installed DRAMs. Set-ting options: Auto, DDR266, DDR333, DDR400.

System BIOS CacheableSelecting Enabled allows caching of the system BIOS ROM at F0000h-FFFFFh, resulting in better system performance. However, if any programwrites to this memory area, a system error may result. Setting options: Enabled,Disabled.

Video BIOS CacheableSelecting Enabled allows caching of the video BIOS ROM at C0000h toC7FFFh, resulting in better video performance. However, if any program writesto this memory area, a system error may result. Setting options: Disabled,Enabled.

Memory Hole At 15M-16MIn order to improve performance, certain space in memory can be reservedfor ISA peripherals. This memory must be mapped into the memory spacebelow 16MB. When this area is reserved, it cannot be cached. Settings:Enabled, Disabled.

Delay Prior to ThermalWhen the CPU temperature reaches a factory preset level, a thermal monitor-ing mechanism will be enabled following the appropriate timing delay speci-fied in this field. With the thermal monitoring enabled, clock modulationcontrolled by the processor’s internal thermal sensor is also activated to keepthe processor within allowable temperature limit. Setting options: 4 Min, 8Min, 16 Min, 32 Min.

Page 53: 865GM3/865PEM2 Seriesmsi-ftp.de/Manuals/6763-englv1.0-865GM3865PEM2Series.pdf · 2009-08-19 · 865GM3/865PEM2 Series. ii Manual Rev: 1.0 Release Date: July 2003 FCC-B Radio Frequency

3-14

MS-6763 M-ATX Mainboard

AGP Aperture Size (MB)This setting controls just how much system RAM can be allocated to AGP forvideo purposes. The aperture is a portion of the PCI memory address rangededicated to graphics memory address space. Host cycles that hit the aperturerange are forwarded to the AGP without any translation. The option allowsthe selection of an aperture size of 4, 8, 16, 32, 64, 128, and 256.

Init Display FirstThis item specifies which VGA card is your primary graphics adapter. Settings:PCI Slot, Onboard/AGP.

**On-Chip VGA Setting**

On-Chip VGAThis setting determines whether the system RAM can be allocated to on-chipvideo controller for video purposes. When setting to Enabled, up to 128MBsystem RAM will be allocated to on-chip video controller. Settings: Disabled,Enabled.

On-Chip Frame Buffer SizeFrame Buffer is the video memory that stores data for video display (frame).This field is used to determine the memory size for Frame Buffer. Largerframe buffer size increases video performance. Settings: 1MB, 8MB, 16MB.

Boot DisplayUse this field to select the type of device you want to use as the display(s) ofthe system. Settings: Auto, CRT, TV, EFP. The option EFP refers to the LCDdisplay.

Page 54: 865GM3/865PEM2 Seriesmsi-ftp.de/Manuals/6763-englv1.0-865GM3865PEM2Series.pdf · 2009-08-19 · 865GM3/865PEM2 Series. ii Manual Rev: 1.0 Release Date: July 2003 FCC-B Radio Frequency

3-15

BIOS Setup

OnChip IDE DevicePress <Enter> to enter the sub-menu and the following screen appears:

IDE HDD Block ModeBlock mode is also called block transfer, multiple commands, or multi-ple sector read/write. If your IDE hard drive supports block mode (mostnew drives do), select [Enabled] for automatic detection of the optimalnumber of block read/write per sector the drive can support. Settingoptions: Disabled, Enabled.

Integrated Peripherals

Page 55: 865GM3/865PEM2 Seriesmsi-ftp.de/Manuals/6763-englv1.0-865GM3865PEM2Series.pdf · 2009-08-19 · 865GM3/865PEM2 Series. ii Manual Rev: 1.0 Release Date: July 2003 FCC-B Radio Frequency

3-16

MS-6763 M-ATX Mainboard

IDE DMA Transfer AccessThis setting is used to enable or disable the DMA transfer function ofIDE hard drives under certain operating systems that do not support IDEdrivers, ex: DOS. Setting options: Enabled, Disabled.

On-Chip Primary/Secondary PCI IDEThe integrated peripheral controller contains an IDE interface with sup-port for two IDE channels. Choose Enabled to activate each channelseparately.

IDE Primary/Secondary Master/Slave PIOThe four IDE PIO (Programmed Input/Output) fields let you set a PIOmode (0-4) for each of the four IDE devices that the onboard IDE inter-face supports. Modes 0 through 4 provide successively increasedperformance. In Auto mode, the system automatically determines the bestmode for each device. The settings are: Auto, Mode 0, Mode 1, Mode 2,Mode 3, Mode 4.

IDE Primary/Secondary Master/Slave UDMAUltra DMA/33 implementation is possible only if your IDE hard drivesupports it and the operating environment includes a DMA driver(Windows 95 OSR2 or a third-party IDE bus master driver). If your harddrive and your system software both support Ultra DMA/33, Ultra DMA/66 and Ultra DMA/100, select Auto to enable BIOS support. The settingsare: Auto, Disabled.

**On-Chip Serial ATA Setting**

On-Chip Serial ATAThis setting controls the Serial ATA controller on the south bridge.Options: Disabled, Auto, Legacy Mode, Native Mode. When set toDisabled, the SATA controller will be disabled. When set to Auto, theSATA controller will be automatically controlled by the BIOS. When setto Legacy Mode, the PATA & SATA controllers are combined to sup-port a maximum of 2 IDE drives in each channel. When set to NativeMode, both SATA and PATA controllers are enabled to support a maxi-mum of 6 IDE drives (The support of 6 IDE drives depends on the oper-ating system installed. Currently only Windows 2000 & Windows XPsupport this function.)

Page 56: 865GM3/865PEM2 Seriesmsi-ftp.de/Manuals/6763-englv1.0-865GM3865PEM2Series.pdf · 2009-08-19 · 865GM3/865PEM2 Series. ii Manual Rev: 1.0 Release Date: July 2003 FCC-B Radio Frequency

3-17

BIOS Setup

Serial ATA Port 1/2 ModeWhen On-Chip Serial ATA is set to Legacy Mode, setting options willshow as follows:1. Primary Master=> Serial ATA Port 1/2 will be set to Primary Master.2. Primary Slave=> Serial ATA Port 1/2 will be set to Primary Slave.3. Secondary Master=> Serial ATA Port 1/2 will be set to Secondary Master.4. Secondary Slave=> Serial ATA Port 1/2 will be set to Secondary Slave.

When On-Chip Serial ATA is set to Native Mode, setting options willshow as follows:1. SATA1 Master=> Serial ATA Port 1 will be set to Native Mode Master.2. SATA2 Master=> Serial ATA Port 2 will be set to Native Mode Master.

Onboard DevicePress <Enter> to enter the sub-menu and the following screen appears:

For 865G

Page 57: 865GM3/865PEM2 Seriesmsi-ftp.de/Manuals/6763-englv1.0-865GM3865PEM2Series.pdf · 2009-08-19 · 865GM3/865PEM2 Series. ii Manual Rev: 1.0 Release Date: July 2003 FCC-B Radio Frequency

3-18

MS-6763 M-ATX Mainboard

For 865PE

CSA LAN (Gigabit-LAN) (for 865G)This setting is used to enable/disable the onboard Gigabit LAN controller.Setting options: Disabled, Enabled.

USB ControllerThis setting is used to enable/disable the onboard USB 1.1 controller.Setting options: Disabled, Enabled.

USB 2.0 ControllerThis setting is used to enable/disable the onboard USB 2.0 controller.This setting works only when the operating system installed supportsUSB 2.0 driver, such as Windows 2000/XP/ME. Setting options: Disabled,Enabled.

USB Keyboard/Mouse SupportSet to Enabled if you need to use a USB mouse/keyboard in the operat-ing system that does not support or have any USB keyboard/mouse driverinstalled, such as DOS and SCO Unix.

AC97 AudioAuto allows the motherboard’s BIOS to detect whether you’re using anyaudio device. If so, the onboard audio controller will be enabled. If not,the onboard audio controller will be disabled. If you want to use differ-ent controller cards to connect audio connectors, set the field to Disabled.Setting options: Disabled, Auto.

Page 58: 865GM3/865PEM2 Seriesmsi-ftp.de/Manuals/6763-englv1.0-865GM3865PEM2Series.pdf · 2009-08-19 · 865GM3/865PEM2 Series. ii Manual Rev: 1.0 Release Date: July 2003 FCC-B Radio Frequency

3-19

BIOS Setup

AC97 ModemAuto allows the mainboard to detect whether a modem is used. If a mo-dem is detected, the onboard AC’97 modem controller will be enabled;if not, it is disabled. Disable the controller if you want to use other con-troller cards to connect a modem. Settings: Auto, Disabled.

Onboard LAN Device (for 865PE)This setting is used to enable/disable the onboard 10/100Mbps LANcontroller. Setting options: Disabled, Enabled.

Onboard 1394 Device (for 865PE)This setting is used to enable/disable the onboard IEEE1394 controller.Setting options: Disabled, Enabled.

Super IO DevicePress <Enter> to enter the sub-menu and the following screen appears:

Onboard FDC ControllerSelect Enabled if your system has a floppy disk controller (FDD) in-stalled on the system board and you wish to use it. If you install add-onFDC or the system has no floppy drive, select Disabled in this field. Thesettings are: Enabled and Disabled.

Onboard Serial Port 1/Port 2Select an address and corresponding interrupt for the first and secondserial ports. The settings are: 3F8/IRQ4, 2E8/IRQ3, 3E8/IRQ4, 2F8/IRQ3,Disabled, Auto.

Page 59: 865GM3/865PEM2 Seriesmsi-ftp.de/Manuals/6763-englv1.0-865GM3865PEM2Series.pdf · 2009-08-19 · 865GM3/865PEM2 Series. ii Manual Rev: 1.0 Release Date: July 2003 FCC-B Radio Frequency

3-20

MS-6763 M-ATX Mainboard

Onboard Parallel PortThere is a built-in parallel port on the on-board Super I/O chipset thatprovides Standard, ECP, and EPP features. It has the following options:

Disabled3BC/IRQ7 Line Printer port 0278/IRQ5 Line Printer port 2378/IRQ7 Line Printer port 1

Parallel Port ModeSPP : Standard Parallel PortEPP : Enhanced Parallel PortECP : Extended Capability PortECP + EPP: Extended Capability Port + Enhanced Parallel PortTo operate the onboard parallel port as Standard Parallel Port only, choose“SPP.” To operate the onboard parallel port in the EPP modesimultaneously, choose “EPP.” By choosing “ECP”, the onboard paral-lel port will operate in ECP mode only. Choosing “ECP + EPP” willallow the onboard parallel port to support both the ECP and EPP modessimultaneously.

EPP Mode SelectThe onboard parallel port is EPP Spec. compliant, so after the user choosesthe onboard parallel port with the EPP function, the following messagewill be displayed on the screen: “EPP Mode Select.” At this time eitherEPP 1.7 spec or EPP 1.9 spec can be chosen.

PWRON After PWR-FailThis item specifies whether your system will reboot after a power failureor interrupt occurs. Available settings are:

Off Leaves the computer in the power off state.On Leaves the computer in the power on state.Former-sts Restores the system to the status before power failure or

interrupt occurred.

Page 60: 865GM3/865PEM2 Seriesmsi-ftp.de/Manuals/6763-englv1.0-865GM3865PEM2Series.pdf · 2009-08-19 · 865GM3/865PEM2 Series. ii Manual Rev: 1.0 Release Date: July 2003 FCC-B Radio Frequency

3-21

BIOS Setup

Power Management Setup

ACPI Suspend TypeThis item specifies the power saving modes for ACPI function. If your oper-ating system supports ACPI, such as Windows 98SE, Windows ME and Win-dows 2000, you can choose to enter the Standby mode in S1(POS) or S3(STR) fashion through the setting of this field. Options are:

S1 (POS) The S1 sleep mode is a low power state. In this state, nosystem context is lost (CPU or chipset) and hardwaremaintains all system context.

S3 (STR) The S3 sleep mode is a lower power state where the information of system configuration and open applications/files is saved to main memory that remains poweredwhile most other hardware components turn off to saveenergy. The information stored in memory will be usedto restore the system when a “wake up” event occurs.

MSI Reminds You...S3-related functions described in this section are available onlywhen your BIOS supports S3 sleep mode.

Page 61: 865GM3/865PEM2 Seriesmsi-ftp.de/Manuals/6763-englv1.0-865GM3865PEM2Series.pdf · 2009-08-19 · 865GM3/865PEM2 Series. ii Manual Rev: 1.0 Release Date: July 2003 FCC-B Radio Frequency

3-22

MS-6763 M-ATX Mainboard

Run VGABIOS if S3 ResumeSelecting [Enabled] allows BIOS to call VGABIOS to initialize the VGA cardwhen system wakes up (resumes) from S3 sleep state. The system resumetime is shortened when you disable the function, but system will need an AGPdriver to initialize the VGA card. Therefore, if the AGP driver of the carddoes not support the initialization feature, the display may work abnormallyor not function after resuming form S3.

Power ManagementThis item is used to select the degree (or type) of power saving and is relatedto these modes: Suspend Mode and HDD Power Down. There are three op-tions for power management:

Min Saving Minimum Power Management. Suspend Mode=1 HourMax Saving Maximum Power Management. Suspend Mode=1 MinUser Define Allows end users to configure each mode separately.

Video Off MethodThis determines the manner in which the monitor is blanked.

V/H SYNC+Blank This selection will cause the system to turn offthe vertical and horizontal synchronization portsand write blanks to the video buffer.

Blank Screen This option only writes blanks to the videobuffer.

DPMS Initial display power management signaling.

Video Off In SuspendThis option enables the monitor to be turned off during the suspend mode.Settings: Yes, No.

Suspend TypeThis setting allows you to select the type of Suspend mode. Setting options:Stop Grant (saves the state of the entire system to disk and then powers off thesystem), PwrOn Suspend (the CPU and core system remain powered on in avery low-power mode).

MODEM Use IRQThis determines the IRQ in which the MODEM can use. Activity of the se-lected IRQ always awakens the system. Settings: 3, 4, 5, 7, 9, 10, 11, NA..

Page 62: 865GM3/865PEM2 Seriesmsi-ftp.de/Manuals/6763-englv1.0-865GM3865PEM2Series.pdf · 2009-08-19 · 865GM3/865PEM2 Series. ii Manual Rev: 1.0 Release Date: July 2003 FCC-B Radio Frequency

3-23

BIOS Setup

Suspend ModeIf system activity is not detected for the length of time specified in this field,all devices except CPU will be shut off. Settings are Disabled, 1 Min, 2 Min,4 Min, 8 Min, 12 Min, 20 Min, 30 Min, 40 Min and 1 Hour.

HDD Power DownIf HDD activity is not detected for the length of time specified in this field, thehard disk drive will be powered down while all other devices remain active.Settings: Disabled, 1 through 15 Min.

Soft-Off by PWR-BTTNThis feature allows users to configure the power button function. Settingsare:

Instant-Off The power button functions as a normal power-on/-offbutton.

Delay 4 Sec. When you press the power button, the computer entersthe suspend/sleep mode, but if the button is pressed formore than four seconds, the computer is turned off.

CPU THRM-ThrottlingThe item allows you to specify the CPU speed (at percentage) to which it willslow down when the CPU reaches the predetermined overheat temperature.Settings range from 12.5% to 87.5% at 12.5% increment.

Wake-Up By PCI Card, USB KB Wake-Up From S3These fields specify whether the system will be awakened from power savingmodes when activity or input signal of the specified hardware peripheral orcomponent is detected.

Resume By AlarmThe field is used to enable or disable the feature of booting up the system ona scheduled time/date.

Date (of Month) AlarmThe field specifies the date for Resume By Alarm. Settings: 0~31.Time (hh:mm:ss) AlarmThe field specifies the time for Resume by Alarm. Format is <hour><minute><second>.

Page 63: 865GM3/865PEM2 Seriesmsi-ftp.de/Manuals/6763-englv1.0-865GM3865PEM2Series.pdf · 2009-08-19 · 865GM3/865PEM2 Series. ii Manual Rev: 1.0 Release Date: July 2003 FCC-B Radio Frequency

3-24

MS-6763 M-ATX Mainboard

**Reload Global Timer Events**Primary/Secondary IDE 0/1, FDC/COM/LPT Port, PCI PIRQ [A-D]#Global Timer Events are I/O events whose occurrence can prevent the systemfrom entering a power saving mode or can awaken the system from such amode. In effect, the system remains alert for anything which occurs to a de-vice that is configured as Enabled, even when the system is in a power downmode.

MSI Reminds You...If you have changed this setting, you must let the system boot upuntil it enters the operating system, before this function will work.

Page 64: 865GM3/865PEM2 Seriesmsi-ftp.de/Manuals/6763-englv1.0-865GM3865PEM2Series.pdf · 2009-08-19 · 865GM3/865PEM2 Series. ii Manual Rev: 1.0 Release Date: July 2003 FCC-B Radio Frequency

3-25

BIOS Setup

PNP/PCI Configurations

This section describes configuring the PCI bus system and PnP (Plug &Play) feature. PCI, or Peripheral Component Interconnect, is a system whichallows I/O devices to operate at speeds nearing the speed the CPU itself useswhen communicating with its special components. This section covers somevery technical items and it is strongly recommended that only experiencedusers should make any changes to the default settings.

PNP OS InstalledWhen set to Yes, BIOS will only initialize the PnP cards used for booting(VGA, IDE, SCSI). The rest of the cards will be initialized by the PnP oper-ating system like Windows 98. When set to No, BIOS will initialize all thePnP cards. So, select Yes if your operating system is Plug & Play aware.

Reset Configuration DataNormally, you leave this field Disabled. Select Enabled to reset ExtendedSystem Configuration Data (ESCD) when you exit Setup if you have installeda new add-on card and the system reconfiguration has caused such a seriousconflict that the operating system cannot boot. Setting options: Enabled,Disabled.

Resources Controlled ByThe Award Plug and Play BIOS has the capacity to automatically configure

Page 65: 865GM3/865PEM2 Seriesmsi-ftp.de/Manuals/6763-englv1.0-865GM3865PEM2Series.pdf · 2009-08-19 · 865GM3/865PEM2 Series. ii Manual Rev: 1.0 Release Date: July 2003 FCC-B Radio Frequency

3-26

MS-6763 M-ATX Mainboard

all of the boot and Plug and Play compatible devices. However, this capabilitymeans absolutely nothing unless you are using a Plug and Play operating sys-tem such as Windows® 95/98. If you set this field to “manual” choose specificresources by going into each of the sub menu that follows this field (a submenu is preceded by a “ ”). Setting options: Auto (ESCD), Manual.

IRQ ResourcesThe items are adjustable only when Resources Controlled By is set to Manual.Press <Enter> and you will enter the sub-menu of the items. IRQ Resourceslist IRQ 3/4/5/7/9/10/11/12/14/15 for users to set each IRQ a type dependingon the type of device using the IRQ. Settings are:

PCI Device For Plug & Play compatible devices designed for PCIbus architecture.

Reserved The IRQ will be reserved for further request.

PCI/VGA Palette SnoopWhen set to Enabled, multiple VGA devices operating on different buses canhandle data from the CPU on each set of palette registers on every videodevice. Bit 5 of the command register in the PCI device configuration space isthe VGA Palette Snoop bit (0 is disabled). For example, if there are two VGAdevices in the computer (one PCI and one ISA):

The setting must be set to Enabled if any ISA bus adapter in the system re-quires VGA palette snooping.

INT Pin 1~8 AssignmentThese items specify the IRQ line for each PCI slot. Settings: 3, 4, 5, 7, 9, 10,11, 12, 14, 15, Auto. Selecting Auto allows BIOS to automatically determinethe IRQ line for each PCI slot.

VGA Palette Snoop Bit Setting Action

Disabled Data read or written by the CPU is only directed to the PCIVGA device’s palette registers.

Enabled Data read or written by the CPU is directed to both the PCIVGA device’s palette registers and the ISA VGA device’spalette registers, permitting the palette registers of both VGAdevices to be identical.

Page 66: 865GM3/865PEM2 Seriesmsi-ftp.de/Manuals/6763-englv1.0-865GM3865PEM2Series.pdf · 2009-08-19 · 865GM3/865PEM2 Series. ii Manual Rev: 1.0 Release Date: July 2003 FCC-B Radio Frequency

3-27

BIOS Setup

PC Health Status

This section shows the status of your CPU, fan, overall system status,etc. Monitor function is available only if there is hardware monitoring mecha-nism onboard.

Chassis Intrusion DetectThe field enables or disables the feature of recording the chassis intrusionstatus and issuing a warning message if the chassis is once opened. To clearthe warning message, set the field to Reset. The setting of the field will auto-matically return to Enabled later. Setting options: Enabled, Reset, Disabled.

CPU Warning TemperatureIf the CPU temperature reaches the upper limit preset in this setting, the warn-ing mechanism will be activated. This helps you to prevent the CPU overheatproblem.

Current System/CPU Temp, Current CPU/System Fan Speed, Vcore(V),VTT(V), Vcc3(V), +5V, +12V, -12V, -5V, VBAT(V), 5VSB(V)These items display the current status of all of the monitored hardware de-vices/components such as CPU voltages, temperatures and all fans’ speeds.

Shutdown TemperatureThis option is for setting the shutdown temperature level for the processor.When the processor reaches the temperature you set, the system will be shutdown.

Page 67: 865GM3/865PEM2 Seriesmsi-ftp.de/Manuals/6763-englv1.0-865GM3865PEM2Series.pdf · 2009-08-19 · 865GM3/865PEM2 Series. ii Manual Rev: 1.0 Release Date: July 2003 FCC-B Radio Frequency

3-28

MS-6763 M-ATX Mainboard

Warning BeepThis setting allows you to monitor the operation of the CPU fan. Setting toEnabled will activate the warning beep once the system detects the malfunc-tion/halt of the CPU fan.

Page 68: 865GM3/865PEM2 Seriesmsi-ftp.de/Manuals/6763-englv1.0-865GM3865PEM2Series.pdf · 2009-08-19 · 865GM3/865PEM2 Series. ii Manual Rev: 1.0 Release Date: July 2003 FCC-B Radio Frequency

3-29

BIOS Setup

Use this menu to specify your settings for frequency/voltage control.

Auto Detect PCI ClkThis item is used to auto detect the PCI slots. When set to Enabled, the systemwill remove (turn off) clocks from empty PCI slots to minimize the electro-magnetic interference (EMI). Setting options: Enabled, Disabled.

Spread SpectrumWhen the motherboard’s clock generator pulses, the extreme values (spikes)of the pulses creates EMI (Electromagnetic Interference). The Spread Spec-trum function reduces the EMI generated by modulating the pulses so that thespikes of the pulses are reduced to flatter curves. If you do not have any EMIproblem, leave the setting at Disabled for optimal system stability andperformance. But if you are plagued by EMI, setting to Enabled for EMIreduction. Remember to disable Spread Spectrum if you are overclockingbecause even a slight jitter can introduce a temporary boost in clockspeedwhich may just cause your overclocked processor to lock up.

CPU ClockThis setting specifies the clock frequency of the CPU host bus (FSB). It pro-vides a method for end users to overclock the processor accordingly.

Frequency/Voltage Control

Page 69: 865GM3/865PEM2 Seriesmsi-ftp.de/Manuals/6763-englv1.0-865GM3865PEM2Series.pdf · 2009-08-19 · 865GM3/865PEM2 Series. ii Manual Rev: 1.0 Release Date: July 2003 FCC-B Radio Frequency

3-30

MS-6763 M-ATX Mainboard

The Default Setting is the default values set by the mainboard manufac-turer specifically for optimal performance of the mainboard.

When you select Load Default Setting, a message as below appears:

Pressing Y loads the default factory settings for optimal systemperformance.

Load Default Setting

Page 70: 865GM3/865PEM2 Seriesmsi-ftp.de/Manuals/6763-englv1.0-865GM3865PEM2Series.pdf · 2009-08-19 · 865GM3/865PEM2 Series. ii Manual Rev: 1.0 Release Date: July 2003 FCC-B Radio Frequency

3-31

BIOS Setup

Set Supervisor/User Password

MSI Reminds You...About Supervisor Password & User Password:Supervisor password: Can enter and change the settings of

the setup menu.User password: Can only enter but do not have the

right to change the settings of the setupmenu.

When you select this function, a message as below will appear on thescreen:

Type the password, up to six characters in length, and press <Enter>.The password typed now will replace any previously set password from CMOSmemory. You will be prompted to confirm the password. Retype the pass-word and press <Enter>. You may also press <Esc> to abort the selection andnot enter a password.

To clear a set password, just press <Enter> when you are prompted toenter the password. A message will show up confirming the password will bedisabled. Once the password is disabled, the system will boot and you canenter Setup without entering any password.

When a password has been set, you will be prompted to enter it everytime you try to enter Setup. This prevents an unauthorized person from chang-ing any part of your system configuration.

Additionally, when a password is enabled, you can also have AwardBIOS to request a password each time the system is booted. This would pre-vent unauthorized use of your computer. The setting to determine when thepassword prompt is required is the Security Option of the ADVANCED BIOSFEATURES menu. If the Security Option is set to System, the password isrequired both at boot and at entry to Setup. If set to Setup, password promptonly occurs when you try to enter Setup.