85557446 Tong Hop Lenh Ericsson

Glossary (danh sch, cc t chuyn mn)

BSC Base Station ControllerCF Central Functions-nhim v chnh, chc nng trung tmCON LAPD Concentrator-tp trungDP Digital PathIS Interface SwitchMO Managed ObjectRX ReceiverTF Timing Function(chc nng nh thi)TG Transceiver GroupTRXC Transceiver ControllerTS Time Slot Handler-b iu khin khe thi gianTX Transmitter-my phtpooltraf The number of transcoder resources currently used in traffic

per pool. DCP=dcp Digital connection point number-s im kt ni sDCP1=dcp1 Digital Connection Point (DCP) number used for the

signalling path to the TRXCNumeral 0 - 511

DCP2=dcp2 DCP number used for the speech and data connections to the TRXC

Two DCP2s, for TRXCs using 16 Kbps Abis paths, or eight DCP2s, for TRXCs using 64 Kbps Abis paths, must be given. The DCP2s given must be consecutive(lin tc). The DCP2s are sorted into ascending order. If two DCP2s are given, the lower range DCP2 value is associated(kt hp) with TSs 0 to 3, and the higher range DCP2 is associated with TSs 4 to 7. If eight DCP2s are given, the lower range DCP2 value is associated with TS 0 and the higher range DCP2 value is associated with TS 7.Numeral 0 - 511

SIG=sig Signalling type UNCONC UnconcentratedCONC LAPD ConcentrationMPLEX16

16K MultiplexMPLEX32 32K Multiplex

TEI Terminal Endpoint Identifier(nhn dng)OML Operation and Maintenance(bo dng) LinkRXD RECEIVER DIVERSITY- nhy thu

BCCH Broadcast Control Channel-knh iu khin qung b

DCHNO=dchno(TCH) Absolute radio frequency channel number(ng,chnh xc) Maximum 32 Absolute Radio Frequency Channel Number (ARFCNs) per channel group are allowed. (31 if channel group 0).Numeral 128 - 251 (GSM 800) Numeral 1 - 124 (GSM 900, P-band) Numeral 0, 975 - 1023 (GSM 900, G1-band) Numeral 512 - 810 (GSM 1900) Numeral 512 - 885 (GSM 1800)

HOP=hop Frequency hopping status OFF The hopping status for the channel group is non-hopping. ON The hopping status for the channel group is hopping for Traffic Channel (TCH) and Stand-alone Dedicated Control Channel (SDCCH).

HSN=hsn Hopping sequence numberNumeral 0 - 63

CBCH=cbch Cell broadcast channel This parameter indicates if Cell Broadcast Channel (CBCH) is included in the Stand Alone Dedicated Control Channel (SDCCH).YES CBCH will be included in one of the SDCCH/8 for a cell or a channel groupNO No SDCCH/8 for a cell or a channel group will include CBCH

CELL=cell Cell designation

This is a symbolic name of a defined cell.CHGR=chgr Channel group number

Numeral 0 - 15 SDCCH=sdcch Required number of SDCCH/8

Numeral 0 - 32 (with combined BCCH 31) TN=tn Timeslot number

Numeral 0 - 7 cgi Cell global identification- nhn dng ton cu(khu

vc) Expressed as(biu din,trnh by) mcc-mnc-lac-ci where:mcc Mobile country codemnc Mobile network codelac Location area codeci Cell identity- nhn dng

BCCHNO=bcchno Absolute radio frequency channel number for Broadcast Control Channel (BCCH) Absolute Radio Frequency Channel Number (ARFCN) already defined for a dedicated channel cannot be given.Numeral 128 - 251 (GSM 800) Numeral 1 - 124 (GSM 900, P-band) Numeral 975 - 1023, 0 (GSM 900, G1-band) Numeral 512 - 885 (GSM 1800) Numeral 512 - 810 (GSM 1900)

BCCHTYPE=bcchtype BCCH type This parameter indicates the combinatons of wanted logical channels on the frequency and timeslot defined for the BCCH in the cell.COMB Combined control channelIndicates that the cell has a combined BCCH and Stand Alone Dedicated Control Channel (SDCCH)/4.COMBC Combined control channel with a Cell Broadcast Channel (CBCH) subchannel

Indicates that the cell has a combined BCCH and SDCCH/4 with a CBCH subchannel.NCOMB Non-combined control channelIndicates that the cell does not have any type of combined BCCH and SDCCH/4.This parameter applies only to internal cells

RLCRP:CELL= 64k 64kbit/s Mode Supported CS3CS4 The Basic Physical Channel (BPC) supports General Packet Radio Service (GPRS) CS-3 or CS-4

EGPRS The BPC supports Enhanced(lm tng, nng cao) General Packet Radio Service (EGPRS)

NONE The BPC does not support EGPRS or GPRS CS-3 or CS-4

bcch Broadcast Control Channels (BCCHs) This parameter indicates the number of deblocked BCCHs in the cell.

bpc Basic Physical Channel individual

This individual is also printed in the RADIO X-CEIVER ADMINISTRATION MANAGED OBJECT CONFIGURATION DATA printout, thus linking the configured logical channels with the Base Transceiver Station (BTS) equipment used for them.

cbch Cell Broadcast Channels (CBCHs) This parameter indicates the number of deblocked CBCHs in the cell.

cell Cell designation This is a symbolic name of a defined cell.

channel Logical channel identity

This parameter consists of the channel type and an individual number.

chband Channel band This parameter indicates the frequency band for the logical channel.The channel band is printed for deblocked channels.800

GSM 800The BPC holding the channel is configured on one or several Absolute Radio Frequency Numbers (ARFCN) within the GSM 800 band in the range 128 - 251.

1800 GSM 1800

The BPC holding the channel is configured on one or several ARFCNs within the GSM 1800 band in the range 512- 885.

1900 GSM 1900The BPC holding the channel is configured on one or several ARFCNs within the GSM 1900 band in the range 512- 810.

P900 Primary GSM 900The BPC holding the channel is configured on one or several ARFCNs exclusively within the primary GSM 900 band in the range 1 - 124.

E900 Extended GSM 900The BPC holding the channel is configured on at least one ARFCN in the extended 'G1' GSM 900 band in the range 0, 975 - 1023.

chgr Channel group numberchrate Channel rate

FR Full rate

HR Half rate

chtype Channel type BCCH

Broadcast Control ChannelCBCH

Cell Broadcast ChannelSDCCH

Stand Alone Dedicated Control ChannelTCH

Traffic Channelicmband Current idle channel interference band

The interference is measured on an idle channel and the value range,from negativeto positive infinity (dBm), is divided into 5 intervals which are called idle channel interference bands. Interference band 1 is the band with the lowest interference. Interference band 5 is the band with the highest interference. An idle or busy SDCCH or TCH belongs to one of the idle channel interference bands.

Numeral 1 - 5noofch Number of deblocked logical channels

A logical channel in state idle, busy or locked is regarded as a deblocked channel.

nooftch Number of traffic channels This number can have a lower and an upper limit. This is because there are BPCs configured with the possibility to be

allocated either as full rate traffic channels (then counted as one channel) or half rate traffic channels (then counted as two channels). These channels are called dual rate channels. In a channel group or a cell, dual rate channels can be mixed with those of a fixed channel rate.

sdcch Stand Alone Dedicated Control Channel (SDCCH) This parameter indicates the number of deblocked SDCCHs in the cell.

spv Speech version If a traffic channel is configured with the possibility to be allocated for either of several speech versions, this parameter shows all the possible speech versions (for example spv = 1,2).

state Logical channel state BLOC

BlockedBUSY

BusyIDLE

IdleLOCK

LockedIf a BPC is configured with the possibility to be allocated either as a full rate traffic channel or two half rate traffic channels, the channel state LOCK is applicable. When one channel rate is allocated to a BPC, the logical channel or channels of the other rate on the same BPC are locked.

NONE No data existed to be printed.

EOT DURING PRINTOUT The operator has cancelled the printout.

FAULT INTERRUPTfault type

A fault interruption occurred during printing.

Fault type:

FORMAT ERRORThe command was incorrectly specified.

UNREASONABLE VALUE

details A parameter was specified with an unreasonable value.

FAULT CODE 3CELL NOT DEFINEDdetails

The cell is not defined. FAULT CODE 19CELL RESOURCES HAVE CHANGED

Cell Resources have changed since printout started. FAULT CODE 27CELL DATA CHANGE IN PROGRESS

Modification of cell data by a command is in progress.

FAULT CODE 38COMMAND NOT VALID FOR EXTERNAL CELLSdetails

The command is not valid for external cells. FAULT CODE 120CELL STATE NOT ACTIVEdetails

The cell has not been activated.

BA-list BCCH Allocation list

1.rxtcp:cell=hni,moty=rxotg; xem TG ca trm Parameters: thng s, tham s, tham bit, gii hn Associated: kt hp, lin kt dedicated to: c tnh cht chuyn mn represented by: trnh by bi, biu din bi

2.dtdii:dip=,snt=,dipp=; Initiate: bt u, khi u, xng Sequence: trnh t, kt ni

3.ntcop:snt=all; xem lung tha hay thiu

SNT=snt Switching network terminal

DIPINF Digital path information related to the Switching Network Terminal (SNT)

ALL All switching network terminals

SNTP=sntp Switching network terminal connection point

4.rlcrp:cell=hni; lnh kim tra thu bao chim knh - CBCH: Cell Broadcast Channel-knh qung b- NOOFTCH: Number of traffic channels

This number can have a lower and an upper limit. This is because there are BPCs configured with the possibility to be(c kh nng,c th) allocated(phn phi,cp pht,nh r v tr) either as(chn 1 trong hai vn ) full rate traffic channels (then counted as one channel) or half rate traffic channels (then counted as two channels). These channels are called dual(hai, i) rate channels. In a channel group or a cell, dual rate channels can be mixed(ln ln,pha trn,hn hp) withthose of a fixed(ng yn,c nh) channel rate.

icmband Current idle channel interference band The interference is measured on an idle channel and the value range,from negativeto positive infinity (dBm), is divided into 5 intervals which are called idle channel interference bands. Interference band 1 is the band with the lowest interference. Interference band 5 is the band with the highest interference. An idle or busy SDCCH or TCH belongs to one of the idle channel interference bands.

BPC Basic Physical Channel

5.rxcdp:mo=rxotg-tg; xem cu hnh ca trm - arfcn:Absolute Radio Frequency Channel Number: s knh tn s radio chun-txad:TX logical address. Numeric value in the range 0 to 31

C0f Carrier zero filling(lm y,ph y) YES

Carrier zero filling is turned on.NO

Carrier zero filling is turned off.

6. rxmfp:mo=rxots-TG-TRX-TS 0&&-TS7; xem s cuc gi trn ts.

conerrcnt Counter for the number of abnormally(khc thng) terminated connections

concnt Counter for the number of connection setup attempts(c gng

lm g)

7. H cu hnh:-dtstp:dip=m trm;(xem trm nm BSC no)-rxtcp:moty=rxotg,cell=m trm1;(xem TG) (rxmfp:mo=rxotg-TG;)-rxmsp:mo=rxotg-TG,subord;(xem cu hnh ca trm) -rxbli:mo=rxotrx-TG-TRX,subord,force;;(lnh blok TRX)-rxese:mo=rxotrx-TG-TRX,subord;;(lnh xa TRX)

rxmoe:mo=RXOTX-125-6 ; rxmoe:mo=RXOTS-125-6-0 ; rxmoe:mo=RXOTS-125-6-1 ; rxmoe:mo=RXOTS-125-6-2 ; rxmoe:mo=RXOTS-125-6-3 ; rxmoe:mo=RXOTS-125-6-4 ; rxmoe:mo=RXOTS-125-6-5 ; rxmoe:mo=RXOTS-125-6-6 ; rxmoe:mo=RXOTS-125-6-7 ; rxmoe:mo=RXORX-125-6 ; rxmoe:mo=RXOTRX-125-6 ;

(rxcdp:mo=rxotg-TG;) +execute: thc hin,thc hin ch dn ca my tnh,hnh hnh, hnh quyt. -rxmsp:mo=rxotg-TG,subord;(xem cu hnh ca trm) FORCE Forced blocking indication(s ch dn)SUBORD Subordinate MOs (di quyn)

All of the MO instances subordinate to the specified MO are included. Parameter SUBORD may be used for a Transceiver Group (TG) or Transceiver Controller (TRXC) in Base Transceiver Station (BTS) logical model G01 and TG, Central Function (CF) or TRXC in the BTS logical model G12.

8.Tch hp trm:-rlcfp:cell=m trm;(xem SDCCH,nhy tn)-rldep:cell= m trm;(xem CGI)-dtqup:dip= m trm;(lnh xem h s trt ca bit)-rxmop:mo=rxotg-tg;(ly version)Khai mi:-ntcop:snt=etm...;

-dtdii:dip=m trm,snt=emt...,dipp=...;;-dtbli:dip=m trm;;-dtble:dip=m trm;;-dtstp:dip=m trm;(xem lung c hay cha)Xe m ta lung ti BSC: -dtdip:dip=ten tram;

i tn dip (khi khai lung nhng b nhm v khi c dip) -dtpnc:dip=m trm mi,newdip=...,-dtble:dip=m trm;-dtstp:dip=m trm; Xa dip:-dtbli:dip=m trm;;-dtdie:dip=m trm;;Khai inner( bn trong, ni b ) cell:

----- Khai bao cell tren MSC-----mgcei:cell=M trm1,CGI= mcc-mnc-lac-ci1,BSC=BHNI;mgcei:cell=M trm2,CGI= mcc-mnc-lac-ci2,BSC=BHNI;mgcei:cell=M trm3,CGI= mcc-mnc-lac-ci3,BSC=BHNI;

a, ParametersBSC=bsc Base Station Controller (BSC) name

The BSC to which the cell is connected.

See Application Information for block MTRAN.CELL=cell Cell name

See Application Information for block MTRAN.CGI=cgi Cell Global Identity (CGI)

See Application Information for block MBSSD.

b, Function

This command initiates a new mobile telephony cell in the Mobile Services Switching Centre and Visitor Location Register (MSC/VLR) Server. The new cell is connected to a Base Station Controller.When the first cell is defined in location area, it defines the location area as well.The order remains after system restart.

Ch : mgcep:cell=m trm bt k no 1;(lnh in ra)Ch : lnh xa CGI trn MSC : phi print cc cell ny trn BSC xem cell ny cn tn ti khng sau mi thc hin cng vic xo:

mgcee:cell=m trm cell1;mgcee:cell=m trm cell2;mgcee:cell=m trm cell3;

Khai GPRS:rlgsi:cell=m trm...;(khai c 3 cell) Khai outer( bn ngoi ) cell(nu cdd yu cu gia cc MSC): mgoci:cell=HTY3156,cgi=452-04-12121-21926,msc=MHN2;

Cc li c th trong CG:Khai bao INTERNAL:+ BSIC: phi l hai ch s(v d: 8=08)Khai bao TCH cho cell(xem tht k)+rlcfi:cell=NDH3064,CHGR=1,DCHNO=768&771&774&777&780&783&786&789&792&795&798&801&804&807;+rlcfi:cell=NDH3065,CHGR=1,DCHNO=769&772&775&778&781&784&787&790&793&796&799&802&805&808;+rlcfi:cell=NDH3066,CHGR=1,DCHNO=770&773&776&779&782&785&788&791&794&797&800&803&806&809; +relation.Thong tin tram moi:Xem version(thay i version):+ RXMOI:MO=RXOTG-tg,TRACO=POOL,COMB=HYB,RSITE=m trm,SWVER=B4402R011L;Xem m cell:+ RXMOC:MO=RXOTRX-tg-trx0, CELL=m trm...;(i vi trm 1800 s cell c nh l cell4,cell5,cell6).CH :Khai bao POWERCONTROL(ch phin bn phn mm)Khai bao Power UL(ch phin bn phn mm)Khi to dev:

BLODI:DEV=RBLT;

(Lnh ny c s dng deblock device s chuyn t trng Idle thi thnh trng thi ABL(Automatic Block))

EXDAE:DEV=RBLT;(Lnh ny c s dng a cc Time Slot (tng ng thut ng Device) chuyn t trng thi In Service thnh trng thi pre-post service)

EXDAI:DEV=RBLT;(Lnh ny c s dng a cc Time Slot (tng ng thut ng Device) chuyn t trng thi pre-post

service thnh trng thi In Service)

BLODE:DEV=RBLT;(Lnh ny c s dng deblock device s chuyn t trng thi ABL(Automatic Block) thnh trng thi Idle)

Chy lnh v Dng li kim tra:+ Khi to Abis: RXAPI:MO=RXOTG-tg,DEV=RBLT2-513&&-543,DCP=1&&31;(Lnh ny c s dng nh ngha mt hoc nhiu Abis paths gia mt BSC v mt BTS. RBLT l device (TS) kt ni t BSC ti BTS.

DCP l s nhn dng device .) + Lnh active cell.+ a cc MO sang trng thi In- Service RXESI:MO=RXOTG-28,SUBORD;(ch full cnh bo v)Lnh ny c s dng a MO (bao gm TG, CF, CON, TF, TRX, TX, RX, TS) vo dch v. C ti 32 MO c th nh ngha trong mt lnh. Nh s dng thng s SUBORD m ta ch dng 1 lnh m c th tc ng n tt c cc MO con ca TG-nh v d trn.+ Deblock cc MO: RXBLE:MO=RXOTG-28,SUBORD;Lnh ny c s dng deblock MO.RLSTC: CELL=HNIPDL1,STATE=ACTIVE;RLSTC: CELL=HNIPDL2,STATE=ACTIVE;RLSTC: CELL=HNIPDL3,STATE=ACTIVE;Lnh ny c s dng thay i trng thi ca Cell hoc CHGR. C cc trng thi l ACTIVE hoc HALTED.C h : nu TCH HP b hin tng local mode c th do cc nguyn nhn sau: -khai sai TEI(c th do c BSC v BTS) -trong lc tch hp mt kt ni hoc do DXU c vn

-cha active dch v(EXDAI, BLODE, RXAPI) -do di trm BTS cha chuyn sang ch remove+ , nu do BSC sai do khai TEI th cch cha li nh sau: -rxbli:mo=rxotg-tg,subord,force; -rxese:mo=rxotg-tg,subord; -rxmoc:mo=rxotg-tg,tei=62(thm nu i sang Con hoc Uncon); -rxesi:mo=rxotg-tg,subord; -rxble:mo=rxotg-tg,subord; 9.T hay i tham s handover: -RLIHC:CELL=cell,iho=;-RLIHC:CELL=cell, SSOFFSETULP=gi tr dng, SSOFFSETULN=ga tr m, QOFFSETULP=gi tr dng, QOFFSETULN=ga tr m, SSOFFSETDLP= ga tr dng, SSOFFSETDLP= ga tr m, MAXIHO=, TMAXIHO=, TIHO=,-RLLUC:CELL=cell, QLIMUL=;

10.Thay i lac:-RLSTC:CELL=,STATE=HALTED;-rldep:cell=,cgi= mcc-mnc-lac-ci;-rldec:cell=,cgi= mcc-mnc-lac-ci;-rlsbc:cell=,t3212=;mcc

Mobile country code Numeral 3 digits

mnc Mobile network code For the number of digits see the Application Information for block ROEPC.

lac Location area codeNumeral 1 - 65535

ci Cell identityNumeral 0 - 65535

CH :-Xem s lng thu bao(mgsvp;) MSC trc v sau khi thay i LAC(ghi li gi-s thu bao)-phi gim T3212 theo yu cu ca CDD trc khi thay-Nu khng c LAI MSC khi thay i LAC th dng lnh khai: MGLAI:LAI=--;-khai inner cell v outer theo yu cu ca CDD (mgbsp:bsc=all; xem tn BSC)-(mgnmp:msc=all; xem tn MSC)

11. Thay i con-uncon: khi nng cp ri( khng cn thit ) Nu l dng con:

-rxmop:mo=rxocon-tg;(xem con)-rxmoc:mo=rxocon-tg,dcp=64&&87;(dng cho con)-rxesi:mo=rxocon-tg;(xa)-rxble:mo=rxocon-tg;(to li con)

12. Lnh reset trm:-rxbli:mo=rxotg-tg,subord,force;(bloking-ngt i)-rxble:mo=rxotg-tg,subord;(deblok-to li)

Lnh reset cell:-rxbli:mo=rxotrx-TG-TRX,subord,force;;(lnh blok TRX)-rxble:mo=rxotrx-TG-TRX,subord;;(deblok-to li TRX)

13. dtbli:dip=m trm;

/ \|dip...|

DTBLI:DIP=+ +;|ALL|\ /

a , Parameters DIP=dip Digital path name Identifier(nhn ra, nhn dng) 1 - 7 characters

ALL All digital paths

b, Function

The command initiates(bt u) blocking of the specified digital path.The order(cp, bc, loi, hng) remains after system restart.

14. Lnh deblock dip:

/ \|dip...|

DTBLE:DIP=+ +;|ALL |\ /

a, Parameters

DIP=dip Digital Path (DIP) nameIdentifier 1 - 7 characters ALL All DIPs See the Application Information for block DIPST.

b, FunctionThis command deblocks the specified DIPs.The order remains after system restart.

15. Lnh kim tra card(hoc reset):-exemp:rp=all,em=all;-dirrp:rp=all;-blrpi:rp=RP,forced;(block)-blrpe:rp=RP;(deblock)

16. Lnh khng a vo dch v:

a, Command / \ |MO=mo... |RXESE:+ +; |MO=mo[,SUBORD]| \ /

b, ParametersMO=mo Managed Object (MO) instance

See Application Information for block RXCTA for the format and the value range of this parameter. All MO classes are valid.

SUBORD Subordinate MOs

All of the MO instances subordinate to the specified MO are included. Parameter SUBORD may be used for a Transceiver

Group (TG) or Transceiver Controller (TRXC) in the Base Transceiver Station (BTS) logical model G01 and TG, Central Function (CF) or TRXC in the BTS logical model G12.

c, Function

This command orders the removing managed objects from service into prepost service. The MO must be manually blocked, that is in state COM. Up to 32 MOs can be specified. The MO instances(trng hp,v d) from different BTS logical models can not be mixed(hn hp).

The answer printout RADIO X-CEIVER ADMINISTRATION MANAGED OBJECT OUT OF SERVICE COMMAND RESULT will be printed giving the result of the command for all specified MO.

The subsequent result printout RADIO X-CEIVER ADMINISTRATION MANAGED OBJECT OUT OF SERVICE COMMAND RESULT will be printed giving the result of the command for all specified MO.

The appearance of answer or result printout depends on exchange property OSSPRINTVER described in Application Information for block ROEPC.

If this MO instance was the last removed object from service in a TG, the observation alarm RADIO X-CEIVER ADMINISTRATION MANAGED OBJECTS IN TRANSCEIVER GROUP MANUALLY BLOCKED will be ceased.

The order in which the MOs are brought out of service in BTS logical model G01 is Time Slot (TS) and Receiver (RX) before the corresponding TRXC; TRXC, Timing Function (TF) and Transmitter (TX) before the corresponding TG.

The order in which the MOs are brought out of service in BTS logical model G12 is RX, TX and TS before the corresponding TRXC; Interface Switch (IS), Concentrator (CON), TRXC, TF, and Digital Path (DP) before the corresponding CF; CF before the corresponding TG.

The parameter SUBORD allows the specified MO instance and its subordinates to be brought out of service.

The order remains after system restart.

17. Lnh a vo dch v :

a, Command / \ |MO=mo... |RXESI:+ +; |MO=mo[,SUBORD[,NOPRINT]] | \ /

b, ParametersMO=mo Managed Object (MO) instance

See Application Information for block RXCTA for format and value range of this parameter. All MO classes are valid.

NOPRINT No result printout

This parameter suppresses the result printout when parameter SUBORD has been specified.

SUBORD Subordinate MOs

All of the MO instances subordinate to the specified MO are included. Parameter SUBORD may be used for a Transceiver Group (TG) or Transceiver Controller (TRXC) in the Base Transceiver Station (BTS) logical model G01 and TG, Central Function (CF) or TRXC in the BTS logical model G12.

c, Function

This command orders bringing Managed Objects into service from prepost service. Up to 32 MOs can be specified. The MOs must be defined, that is, in state DEF. The MO instances from different BTS logical models can not be mixed.

Once an MO has been brought into service it will initially be manually blocked, that is, in state COM. An attempt is then made to load the MO.

The answer printout RADIO X-CEIVER ADMINISTRATION MANAGED OBJECT IN SERVICE COMMAND RESULT will be printed giving the result of the order for each of the MO instances specified by the MO parameter.

A subsequent result printout RADIO X-CEIVER ADMINISTRATION MANAGED OBJECT IN SERVICE RESULT will be given when the in-service order is completed for all MO instances.

If this MO is the first object brought into service in a TG, the observation alarm RADIO X-CEIVER ADMINISTRATION MANAGED OBJECTS IN TRANSCEIVER GROUP MANUALLY BLOCKED will be raised.

The order in which the MOs are brought into service in BTS logical model G01 is TG before the corresponding TRXC, Transmitter (TX) and Timing Function (TF); TRXC before the corresponding Time Slot (TS) and Receiver (RX).

The order in which the MOs are brought into service in BTS logical model G12 is TG before the corresponding CF; CF before the corresponding Interface Switch (IS), Concentrator (CON), TRXC, TF and Digital Path (DP); TRXC before the corresponding RX, TX and TS.

The parameter SUBORD, which may only be used in conjunction with a single MO instance, will print the status of that MO instance and all its subordinates. Upto a maximum of one-hundred and eighty-three MOs can be returned when specifying the SUBORD parameter.

When using parameter SUBORD, MO instances will only be processed if their superior MOs are also defined.

The parameter NOPRINT, which may only be used in conjunction with parameter SUBORD, suppresses the result printout.


18. Lnh xem lung v xem casce ca trm:

rxapp:mo=rxotg-TG;

19.Ch khi nng cp:

-nhy tn-Thay i gia con v uncon;(c th phi xem cu hnh trc ca trm l dng con hay uncon bng lnh: rmop:mo=rxotf-

tg;). Nu nng ln cu hnh 4/4/4 th phi dng CON cho tt c cc TRX. RXMOC:MO=RXOCF-TG,TEI=62,SIG=CONC; RXMOI:MO=RXOCON- TG,DCP=64&&87; RXMOI:MO=RXOTRX- TG TEI,DCP1=..,DCP2.., SIG=CONC;(Thm cc TRX c lin quan) RXMOI:MO=RXOTRX- TG -TEI, DCP1=..,DCP2.., SIG=CONC;(Thm cc TRX c lin quan)

RXMOC:MO=RXOTRX-TG-TRX,SIG=CONC;(Thay i cc TRX khng lin quan)

-Dng lnh halted v active:rlstc:cell=m trm1,state=halted;rlstc:cell=m trm2 ,state=halted;rlstc:cell=m trm3 ,state=halted;

rlstc:cell=m trm1,state=active;rlstc:cell=m trm2,state=active;

rlstc:cell=m trm3,state=active;Khng dng nhy tn hay nhy tn:-Change cells (when FHOP=BB and cell C has one CHGR=0) RLCCC:CELL=m trm1,SDCCH=2,TN=2; RLCFI:CELL=m trm1,DCHNO=;

-when FHOP=SY and cell C has two CHGRs=0,1! RLCCC:CELL= m trm1,CHGR=1,SDCCH=1,TN=1;

20. Xa cell:rlcrp:cell=cell;rxtcp:cell= cell,moty=rxotg;rlvle:cell= cell,chtype=tch;(xa gim st)rlvle:cell= cell,chtype=sdcch;(xa gim st)

rldee:cell= cell(lnh xa)

21. Lnh tng SAE: saaep:sae=502,BLOCK=RTAPH;

saaii:sae=502,BLOCK=RTAPH,ni=2048;(s ni ph thuc vo s thay i ca sae)RXMOI:MO=RXOTRX-67-6, TEI=6, DCP1=146, DCP2=147&148, SIG=UNCONC;rxmoe:mo=rxotrx-67-6;

22. Thm tn s cho cell:-Them tan so: trm BTS v thay rlccc ging nh rlcfp theo cr: rlcfi:cell=sla0221,CHGR=0,DCHNO=68; rlcfi:cell=sla0222,CHGR=0,DCHNO=72;Hin tng Unused hoc Block TRX: -Trm unused c th do thiu tn s.-C th halted li cell ri active nu l Unused.(Xem lnh RXMSP)-Dng lnh RLBDC thay i NUMREQBPC(khi khng th thay i c knh SDCCH) nu l Unused.-Nu khng tng c knh SDCCH do TN(TN=1, hay TN=1&2)-Khi chuyn trm m mt s trm c hin tng block mt s TRX th c th do nhm lung.-Do khai sai bng tn GSM900-GSM1800, cng sut pht 47dbm-45dbm nu Block.-Do gn sai TEI cho cell nn TX b block.-i vi chgr=2 trm chung TG nu TX unused v MISMATCH=cell th c th do li khai sai TRX gn cho mt tn cell ca trm khc.

2 3. Dng cho trm chung TG: RXMsc:MO=RXOTF-TG1,TFMODE=M;(tram chu) RXMsc:MO=RXOTF-TG2,TFMODE=S,TFCOMPNEG= 4580(do ti u-hi ng cu);

TFCOMPNEG Timing function negative compensation value This is the distribution delay between the master TG and slave TG,plus own TG transmitter chain delay, minus the master TG transmitter chaindelay, given in nanoseconds.

Numeral 1 - 10000 TFCOMPPOS Timing function positive compensation value

This is the distribution delay between the master TG and slave TG,

plus own TG transmitter chain delay, minus the master TG transmitter chaindelay, given in nanoseconds.

Numeral 0 - 10000 OMT

TF compensation value configured from OMT within the TG Synchronization function

TFMODE Timing function synchronization mode This is the mode of the timing function in the TG.M

Master, synchronized from the synchronization source and distributed to other TFsThe availability of this parameter value depends on commercial agreements.

S Slave, synchronized from other TFThe availability of this parameter value depends on commercial agreements.

SA Standalone, synchronized from synchronization source

24. Xa TCH v thm TCH: Rlstc:cell=,state=halted;Rlcfe:cell=,chgr=,dchno=;Rlcfi:cell=,chgr=,dchno=;Rlstc:cell=,state=active;

25. Lnh xa chgr v tn s:Rlstc:cell=,state=halted;RLCHC:CELL=,CHGR=,HOP=on hoc off,HSN=hoc 0,maio=,bccd=;(thay i Yes hoc No)Rxtce:mo=rxotg-tg,cell=,chgr;(ngt chgr)Rldge:cell=,chgr;(xa chgr)Rlstc:cell=,state=active;

26. Quan h gia cc cell: RLNRC:CELL=cell,CELLR=cellr,+Nu l xa: RLNRE

1, Functiona, Format 1This command changes neighbour relation data for defined relations.Format 1 is used for the Ericsson1 algorithm. See parameter EVALTYPE in command RLLBC.Issuing a command of format 1 with all optional parameters included will result in a too long command line exceeding the maximum input buffer size of 140 characters. In this case, the command needs to be given two times with some optional parameters in the first command and the rest in the second command so that the maximum input buffer size is not exceeded.For details about the default values see Application Information for block RQCD.The order remains after system restart. b, Format 2This command changes neighbour relation data for defined relations.Format 2 is used for the Ericsson3 locating algorithm. See parameter EVALTYPE in command RLLBC.For details about the default values see Application Information for block RQCD.The order remains after system restart.

27 . BA list v Relation:

BA list:

1.1 Command:

RLMFC:CELL=cell,MBCCHNO=mbcchno...[,LISTTYPE=listtype] [,MRNIC];

1.2 Parameters


This is a symbolic name of a defined cell.LISTTYPE=listtype Type of measurement frequency list.

This parameter indicates in which mode the Mobile Station (MS) will measure on the frequencies in the list.

ACTIVE Measurement frequency list to be used by active MSs

IDLE Measurement frequency list to be used by idle MSs

MBCCHNO=mbcchno Absolute Radio Frequency (RF) channel number for measurement on Broadcast Control Channel (BCCH)

The number is the absolute RF channel number for the BCCH for cells to be measured on by a MS in the cell.Numeral 128 - 251 (GSM 800) Numeral 1 - 124 (GSM 900, P-band) Numeral 975 - 1023, 0 (GSM 900, G1-band) Numeral 512 - 885 (GSM 1800) Numeral 512 - 810 (GSM 1900)

MRNIC Measurement results not interpreted correctly

At updating of the measurement frequencies, measurement results are not interpreted correctly for a period of time.

2 Function

This command initiates or adds frequencies that MSs will measure on in the cell. If the type of measurement frequency list is not specified, then both idle and active lists are changed. The command is only valid for internal cells, which are, cells belonging to the current Base Station Controller (BSC).

If MRNIC is specified, or the cell state is halted, then the updating of the measurement frequencies is performed immediately. In this case the measurement results are not interpreted correctly for a period of time. EXECUTED will be printed.

If MRNIC is not specified, the updating of the measurement frequencies is performed over a period of time and the measurement results are interpreted correctly. ORDERED will be printed and the result printout ADDITION OF CELL MEASUREMENT FREQUENCIES COMPLETED is received.

If the global system type is MIXED, it is possible to add frequencies in the combination of GSM 800 band, GSM 900 band, and GSM 1800 or GSM 1900 band.

The frequencies in G1 band can only be defined in a cell if the feature Extended GSM Frequency Band support is available. The availability of this feature depends on commercial agreements.

Basically up to 32 measurement frequencies can be defined in a frequency list.

If the global system type is MIXED, the following restrictions will apply according to the band in which the BCCH is defined and the combination of measurement frequency bands. The following restrictions apply to both IDLE and ACTIVE list types. In a few cases, when BCCH is in GSM 900 P band or undefined, the restrictions apply to IDLE list only (See Note 5 below). If the list type is not specified, it is set to BOTH. When the list type is set to BOTH, the restrictions are checked for both IDLE and ACTIVE lists.

Li:

EXECUTEDORDEREDNOT ACCEPTEDfault type

Fault type:

FUNCTION BUSY The function is busy.

FORMAT ERRORdetails

The command or a parameter was incorrectly specified.

UNREASONABLE VALUEdetails

The parameter was specified with an unreasonable value.

FAULT CODE 3 CELL NOT DEFINED

The cell is not defined.

FAULT CODE 14 MBCCHNO ALREADY GIVENdetails

The measurement frequency has already been given.

FAULT CODE 21 MAXIMUM NUMBER OF MBCCHNO EXCEEDED

The maximum number of measurement frequencies is exceeded. See chapter "2 Function" in this document for the maximum number of measurement frequencies that can be defined in a measurement frequency list.

FAULT CODE 38 COMMAND NOT VALID FOR EXTERNAL CELLS

The command must not be used for external cells, which are cells belonging to another BSC.

FAULT CODE 50 ACTIVE BA-LIST RECORDING IS ACTIVE

It is not possible to change neither the active list nor the idle list when the function Active BA-List Recording is active for the cell.

FAULT CODE 171 PARAMETER VALUE NOT SUPPORTED BY THIS EXCHANGEdetails

The possibility to define an MBCCHNO in G1 GSM band depends on commercial agreements. Contact the sales organization.

Relation:

1.1 Command

RLNRI:CELL=cell,CELLR=cellr[,SINGLE];

1.2 Parameters


This is a symbolic name of a defined cell.CELLR=cellr Related cell designation

This is a symbolic name of a defined related cell.SINGLE Single direction cell relation

This parameter defines the relation to be a one way relation between the cell and cellr. It means that handover can only be made from CELL to CELLR

When SINGLE is not given, the relation will be mutual, which means that handover in both directions is allowed.

2 Function

This command defines relations between cells. The type of relation between the cells can be either mutual or one-way. When relation is mutual, handover in both directions is allowed.

Mutual relation is default. Relation to an external cell, which is a cell in another Base Station Controller (BSC) or a cell using another Radio Access Technology (RAT), must be SINGLE.

To change the direction of a relation, the neighbour relation must be deleted using command RLNRE and a new relation defined.

It is allowed to define up to 64 Global System for Mobile Communication (GSM) neighbours and 64 UMTS Terrestrial Radio Access Network (UTRAN) Frequency Division Duplex (FDD) neighbours to a cell.


28 . Radio Control Cell, Dynamic HR Allocation Data, Change : RLDHC:CELL=cell+[,DHA=dha][,DTHAMR=dthamr][,DTHNAMR=dthnamr]+;

29. Thay i nhy tn-BB hoc SY:

In BTS Logical Model G01 /RXMOC:MO=mo...+[,FHOP=fhop][,SWVER=swver][,COMB=comb] \

[,RSITE=rsite][,TRACO=traco][,CONFACT=confact] \ [,CONFMD=confmd][,EMG=emg]+; /In BTS Logical Model G12 /RXMOC:MO=mo...+[,FHOP=fhop][,SWVER=swver][,COMB=comb] \ [,RSITE=rsite][,TRACO=traco][,CONFACT=confact] [,CONFMD=confmd][,SIGDEL=sigdel][,AHOP=ahop] \ [,ABISALLOC=abisalloc]+; /

30. Layer (Tng, lp) :

RLLHC:CELL=HNI5093,LAYER=2,LAYERTHR=80,LAYERHYST=2,PSSTEMP=0,PTIMTEMP=0,FASTMSREG=OFF;

31. Thay i CLS state: rllci:cell=HTY0032;(active hay inactive) / |/ \/ \RLLCC:CELL=cell+|,CLSLEVEL=clslevel||,CLSACC=clsacc| |\ /\ / \ / \ |,HOCLSACC=hoclsacc| \ / \ / \/ \| |,RHYST=rhyst||,CLSRAMP=clsramp|+; \ /\ /| /

32. Thay i tham s HR cho cell: RLDMI:Cell=.;(bt hay tt DMSUPP- RLDME) /RLDMC:CELL=cell+[,DMQB=dmqb] \[,DMQG=dmqg] [,DMQBAMR=dmqbamr] [,DMQBNAMR=dmqbnamr] [,DMQGAMR=dmqgamr] [,DMQGNAMR=dmqgnamr] [,DMTHAMR=dmthamr] \ [,DMTHNAMR=dmthnamr]+;

/

33. Xem EM v xem TRX:EXEMP:RP=ALL,EM=ALL;ntcop:snt=all;34. Kim tra s TRXs:Command to check current number of TRXs: RXMSP:MOTY=RXOTRX;

Select the appropriate action according to the fault:

LOF or LOS Failure(mt kh nng) in receive direction(s iu khin) detected(nhn ra,pht hin ra) by local termination equipment. Go to Step 34.

ALL1 or AIS Alarm indication(du hiu) signal transmitted by remote(t xa, xa) end termination equipment due to(do , nh c) failure upstreams. Further action is outside the scope of this Operational Instruction. Consult the next level of maintenance support and return to Step 50 in this Operational Instruction.

RDI Remote defect(mt ht) indication. Failure in transmit(truyn ,pht tn hiu) direction detected by remote end termination equipment. Go to Step 34.

ERATE or CS ES Severe degradation of signal. Go to Step 43. LOMF or REFM Faults related to multiframe signalling (TS16). Go to Step 38.

AISM Alarm indication signal in TS16 transmitted by remote end termination equipment due to failure affecting the signalling upstreams. Further action is outside the scope of this Operational Instruction. Consult the next level of maintenance support and return to Step 50 in this Operational Instruction.Other faults Further action is outside the scope of this Operational Instruction. Consult the next level of maintenance support and return to Step 50 in this Operational Instruction.

35. Khi to ng dn cuc gi:RAPTI:LCH=2485;

Tracing(dau vet, lan theo) and printing(in ra) of connections using logical channel number 2485 is made.36. Xem s TG dang hoat dong va so TRX dang su dung:

rxmsp:moty=rxotg;rxmsp:moty=rxotrx;

37. Li v LRDEC: FAULT CODE 50 ACTIVE BA-LIST RECORDING( c ghi) IS ACTIVE

When the cell state is ACTIVE and Active BA-List Recording is active for the cell, it is not possible to change the RF channel for BCCH.

Sa li 1:

a, Command

/ \ |rid...|RABRP:RID=+ +; |ALL | \ /

b, ParametersRID=rid Active BA-list Recording Identity Identifier BARID00 - BARID63

ALL All RIDs C,Function

This command is used to print the details of one, severalor all RIDs. The printout ACTIVE BA-LIST RECORDING DETAILSwill be given.The order does not remain after system restart.

Sa li 2:

A, CommandRABRE:RID=rid[,MRNIC];

B, ParametersMRNIC Measurement Results Not Interpreted(trnh din,th hin) Correctly(ng n,ph hp) When re-creating the active BA-lists, Measurement Results are interpreted incorrectly during(trong thi gian) a few minutes.

RID=rid Active BA-list Recording Identity Identifier BARID00 - BARID63

C, FunctionThis command is used to interrupt a recording for oneRID, before the duration time has elapsed.The command is only accepted for RIDs that are in stateRECORDING or CONFIGURATION OF BA-LISTS. The state of theinterrupted RID will then change to RECORDING COMPLETE.If MRNIC is specified, then the re-creation of the activeBA-lists is performed immediately. In this case themeasurement results are interpreted incorrectly duringa few minutes, e.g. a faulty handover can occur. Otherwise,the re-creation of the active BA-lists is performed overa period of time and the measurement results are

interpreted correctly.The printout ACTIVE BA-LIST RECORDING TERMINATION RESULT will be given when the recording is ended. The printout isrouted both to the ordering IO device and to the IO deviceindicated by the printout category.The order does not remain after system restart.

D, Examples

3.1 Example 1

RABRE:RID=BARID00,MRNIC;The active BA-list recording will be terminatedfor the RID BARID00. When updating the active BA-lists,measurement result will not be interpreted correctlyfor a period of time.

38. Lin qua n BA-list(dng khc c th cha dng)

/ \ |,CELL=cell... | | / \| |,CELL=ALL |,CSYSTYPE=csystype|| RABDE:RID=rid + \ /+; | / \ | | |tmbcchno...| | |,TMBCCHNO= + + | | |ALL | | \ /

a, ParametersCELL=cell Cell designation

Symbolic name, maximum 7 characters

ALL All Internal cells

CSYSTYPE=csystype System Type Identifier GSM800

GSM 800GSM900

GSM 900GSM1800

GSM 1800GSM1900

GSM 1900RID=rid Active BA-list Recording Identity

Identifier BARID00 - BARID63 TMBCCHNO=tmbcchno Absolute Radio Frequency (RF) channel number for test

measurement on BCCHNumeral 128 - 251 (GSM 800)

Numeral 0 - 124 (GSM 900) Numeral 975 - 1023 (GSM 900) Numeral 512 - 885 (GSM 1800) Numeral 512 - 810 (GSM 1900)

The number is the absolute RF channel number for the BCCH for cells to be measured on by a mobile station in the cell.

ALL All TMBCCHNOs connected to the RID

b,Function

This command removes cells or frequencies from an active recording. During the recording the frequencies are included in the active BCCH Allocation (BA) lists, for all cells connected to the RID.

It is possible to remove one cell, several cells, all cells or all cells of a specific system type from a RID or remove one frequency, several frequencies or all frequencies from a RID.

The command is only accepted for RIDs that are in state ALLOCATED, USED or RECORDING COMPLETE.

If all cells are removed from the RID the state is changed to ALLOCATED.

The order does not remain after system restart.

C, Examples

- Example 1RABDE:RID=BARID15,CELL=KNA11;

Removes the cell KNA11 from the RID BARID15.

- Example 2RABDE:RID=BARID25,CELL=ALL,CSYSTYPE=GSM1900;

Removes all cells of the system type GSM 1900 from the RID BARID25.

- Example 3RABDE:RID=BARID37,TMBCCHNO=530&&550;

Removes TMBCCHNOs 530 up to 550 from the RIDBARID37.

- Example 4RABDE:RID=BARID53,TMBCCHNO=ALL;

Removes all the test BCCH frequencies from the RID BARID53.

39.Lnh print cc ETM:

1.1 Command / \ |SDIP=sdip... |TPSTP:[IO=io,]+ +; |SDIP=ALL[,STATE=state...]| \ /

1.2 ParametersIO=io Input/Output (IO) device name

Identifier 1 - 7 characters SDIP=sdip Synchronous Digital Path (SDIP) name

Identifier 1 - 7 characters ALL

All SDIPsSTATE=state State of SDIP

BLOC Blocked

PBLOC Partly blocked

TRAFBLOC Traffic blocked

TRAFLIM Traffic limited

WO Working

2 Function

This command prints the state of specified SDIP on specified or default IO device.

Printout SYNCHRONOUS DIGITAL PATH STATE is received.

Up to 10 SDIPs can be specified in each command.


3 Examples

3.1 Example 1TPSTP:SDIP=LONDON;

The state of SDIP LONDON is printed.

3.2 Example 2TPSTP:IO=AT-4,SDIP=LONDON&OSLO;

The state of the SDIPs LONDON and OSLO is printed on IO device AT-4.

3.3 Example 3TPSTP:SDIP=ALL;

The state of all SDIPs is printed.

3.4 Example 4TPSTP:IO=AT-4,SDIP=ALL,STATE=WO&BLOC;

All working and all blocked SDIPs are printed on IO device AT-4.

40. Deblock cc ETM:

1.1 Command / // \\\ | ||,MS=ms...||| |sdip|+,HP +|| | ||,HP=hp...|||TPBLE:SDIP=+ ||,LP=lp...||+; | \\ //| |sdip... | | | |ALL | \ /

1.2 ParametersHP=hp Higher order Path (HP)

For the value ranges, see the Application Information for SDIP owning block.

LP=lp Lower order Path (LP)


MS=ms Multiplex Section (MS)


SDIP=sdip Synchronous Digital Path (SDIP) nameIdentifier 1 - 7 characters ALL

All SDIPs

2 Function

This command deblocks either the whole SDIP including all existing lower layers, or only the MS, the HP, or the LP when they are specified.

Result printout SYNCHRONOUS DIGITAL PATH DEBLOCKING RESULT is received.

Up to 10 SDIPs can be specified in each command.


3 Examples

3.1 Example 1TPBLE:SDIP=LONDON;

The whole SDIP LONDON is manually deblocked.

3.2 Example 2TPBLE:SDIP=LONDON,MS=MS-0&-1;

The MS-0 and MS-1 within SDIP LONDON are manually deblocked.

3.3 Example 3TPBLE:SDIP=LONDON,HP;

The HP within SDIP LONDON is manually deblocked.

3.4 Example 4TPBLE:SDIP=LONDON,LP=VC12-0&&-47;

The LPs VC12-0 to VC12-47 within SDIP LONDON are manually deblocked.

3.5 Example 5TPBLE:SDIP=LONDON&OSLO&NACKA;

The SDIPs LONDON, OSLO, and NACKA are manually deblocked.

3.6 Example 6TPBLE:SDIP=ALL;

All SDIPs are manually deblocked.

3.7 Example 7TPBLE:SDIP=CHICAGO,HP=STS1-0&-1

The HPs STS1-0 and STS1-1 within SDIP CHICAGO are manually deblocked.

41. Dng blocking RP:

1.1 Command

BLRPI:RP=rp[,FORCED];

1.2 Parameters

RP=rp Regional Processor (RP) addressNumeral 0 - 1023

The maximum value is defined by the Size Alteration Event (SAE) 304FORCED Blocks RP regardless of Extension Module (EM) state and device state.

2 Function

This command is used when blocking an RP, where the logical state of the RP is set to Manually Blocked (MB). The bus senders are blocked from sending signals on the RP bus.

In the case of RPs with an EM bus, the control of the connected equipment, EMs, is transferred automatically, if possible, to the twin RP through local restarts of the EMs.

If the control of EMs cannot be transferred, all EMs linked to the RP and all devices connected to the EMs must be manually blocked before the command can be accepted.

For some RPs without EM bus it is sufficient that all devices connected to the EMs are manually blocked before the command can be accepted.

If the parameter FORCED is given, the RP is blocked regardless of EM state and device state. This parameter shall be used with care as it can result in traffic disturbance. Special checks requested by EM owner to ensure that critical IO-channel system resources are not lost, are still done.

For some RP types without an EM bus, the commands for blocking and deblocking of EM are not applicable. The operational state for the EM is then controlled by blocking and deblocking the RP. For these RPs, some checks normally performed at BLEMI are performed at BLRPI instead.


3 Examples

3.1 Example 1

BLRPI:RP=2;

An RP with address 2 is blocked (if EM state and device state are manually blocked).

3.2 Example 2

BLRPI:RP=5,FORCED;

An RP with address 5 is blocked regardless of EM state and device state.

42. Remove EM(expension module):

1.1 Command

EXEME:RP=rp[,RPT=rpt],EM=em;

1.2 Parameters

EM=em Extension Module (EM) addressNumeral 0 - 63


Actual maximum value is defined by Size Alteration Event (SAE) 304.RPT=rpt RP address for twin(sinh i, cp i) RP

Numeral 0 - 1023

Actual maximum value is defined by SAE304.

2 Function

The command is used in order to remove the definition of an EM. Devices connected to the EM must be manually blocked. Also the EM must be blocked except(tr ra, loi ra) for the RP-types for which EM blocking command is not applicable(c th ng dng c). For these RP-types the RP must be blocked instead(thay vi, thay cho). If the EM is controlled by an RP pair, both the RP addresses must be indicated(chi ra).


3 Examples

3.1 Example 1

EXEME:RP=16,RPT=17,EM=4;

The definition of the EM with address 4, in the RP pair which consists of RPs 16 and 17, is removed.

3.2 Example 2

EXEME:RP=50,EM=5;

The definition of the EM with address 5, in the single RP 50, is removed.

43. Lnh ny dng xa Regional Software Units (RSU):

1.1 Command

/ \ | / \| | |ALL || / \ |SUNAME=+ +| |RP=rp... | | |suname||EXRUE:+ +,+ \ /+; |RP=rp,RPT=rpt| | / \ | \ / | |ALL | | |SUID=+ + | | |suid| | | \ / | \ /

1.2 Parameters


The maximum value is defined by Size Alteration Event (SAE) 304.RPT=rpt Regional Processor Twin (RPT) address

Numeral 0 - 1023

The maximum value is defined by SAE=304.SUID=suid Software Unit (SU) identity

Identifier 1 - 32 characters

If the identifier contains any character, other than letters or digits then the string must be given within quotation marks.

SUNAME=suname SU nameIdentifier 1 - 8 characters

2 Function

Command EXRUE is used to delete defined Regional Software Units (RSU) in an RP (RP pair) or in a suite of RPs. The specified suite of RPs must not consist of more than 128 RPs.

The specified RP or RPs must be manually blocked (not blocked for repair or blocked for function change). Parameter SUID must be specified if more than one version of the specified SU is defined.

If a specific SUNAME (SUID) is given, it must be defined in all the specified RPs.

The RSUs must be deleted at the same time for both RPs in an RP pair. The two addresses in the pair can be specified in two different ways as follows:

With parameters RP and RPT With parameter RP for both addresses

If the command is used to delete definitions of SUs in more than one RP (RP pair) at a time, all the RP addresses (including the RPT addresses) must be specified with parameter RP.

An RSU of type Firmware Replacement Package (FRP) shall not be deleted unless it shall be replaced or it is faulty. This is to avoid that, at repair of RPs, an RP board is entered and started with an old FRP RSU. Although an FRP RSU is removed by command EXRUE the FRP RSU will continue to be working in the RP (if it once has been loaded to the RP).


3 Examples

3.1 Example 1

EXRUE:RP=7,RPT=8,SUNAME=RPFDR;

The definition of the RSU with name RPFDR in RP 7 and RPT 8 is deleted.

3.2 Example 2

EXRUE:RP=7,SUID="5/CAA1053092/1R1A02";

The definition of an RSU with product identity 5/CAA 105 3092/1 R1A02 in RP 7 is deleted.

3.3 Example 3

EXRUE:RP=7&20,SUNAME=RPFDR;

The definition of the RSU with name RPFDR in RP 7 and RP 20 is deleted.

3.4 Example 4

EXRUE:RP=7&&20,SUNAME=RPFDR;

The definition of the RSU with name RPFDR in the RP suite RP 7 through RP 20 is deleted.

3.5 Example 5

EXRUE:RP=7&&20,SUNAME=ALL;

All RSU definitions in the RP suite RP 7 through RP 20 are deleted.

3.6 Example 6

EXRUE:RP=25,SUID="9000/CXC 152 001 R1A01";

The FRP RSU definition with product identity 9000/CXC 152 001 R1A01 in RP 25 is deleted. If loaded to the RP, the FRP will not be removed from the RP.

44. Lnh ny dng remove cc RP:

1.1 Command

EXRPE:RP=rp[,RPT=rpt];

1.2 Parameters


The maximum value is defined by Size Alteration Event (SAE) 304.RPT=rpt RP twin address

Numeral 0 - 1023

The maximum value is defined by SAE 304.

2 Function

This command is used in order to remove the definition of an RP or an RP pair.

The command requires that the affected RP is manually blocked and and that the definition of associated equipment has been removed.

If the RP is loadable, all Software Unit (SU) definitions must also be removed (by command EXRUE).


3 Examples

3.1 Example 1

EXRPE:RP=17;

The definition of a single RP, with address 17, is removed.

3.2 Example 2

EXRPE:RP=17,RPT=8;

The definition of an RP pair, with addresses 17 and 8, is removed.

45. Khi to li RP:

1.1 Command

EXRPI:RP=rp[,RPT=rpt],TYPE=type[,DEFRSU];

1.2 Parameters

DEFRSU Define Regional Software UnitsRP=rp Regional Processor (RP) address

Numeral 0 - 1023

The maximum value is defined by Size Alteration Event (SAE) 304.RPT=rpt RP twin address

Numeral 0 - 1023

The maximum value is defined by SAE 304.TYPE=type RP type

Text string 1 - 7 characters

2 Function

This command initiates RP equipment for the specified RP-address (or addresses) and for the specified type of RP.

If parameter DEFRSU is given then default Operating System (OS) Regional Software Units (RSU), as specified in database table RPSDEFOSRSUS, are defined for the RP. The effect of parameter DEFRSU is the same as if these RSUs had been defined by command EXRUI after command EXRPI.

Possible RP types are described in Application Information for block RPADM.

All valid types of RPs, with characteristics and properties of the different types, can be listed by printing the database tables RPSRPTYPES, RPSTYPESTOPROPS and RPSRPPROPERTIES.Use generic DBS print command DBTSP.


Note: Also an RSU of type Firmware Replacement Package (FRP) can be defined for the RPs by use of parameter DEFRSU. FRP RSUs can be included in the DBS table RPSDEFOSRSUS.

3 Examples

3.1 Example 1

EXRPI:RP=17,TYPE=RPM1A;

An RP of type RPM1A is defined. It has RP address 17.

3.2 Example 2

EXRPI:RP=17,RPT=8,TYPE=RPM6A;

An RP pair of type RPM6A is defined. The pair will control the same EMs. The pair has RP addresses 17 and 8.

3.3 Example 3

EXRPI:RP=30,RPT=31,TYPE=RPM2B;

An RP pair of type RPM2B is defined. It has RP addresses 30 and 31.

3.4 Example 4

EXRPI:RP=20,type=STC1A;

A Signalling Terminal Central (STC) with RP address 20 is defined.

3.5 Example 5

EXRPI:RP=40,TYPE=RPI1A,DEFRSU;

An RP of type RPI1A is defined. Default OS RSUs are defined for the RP. The RP has RP address 40.

46. Khi to cc kt ni SNT:

1.1 Command

/ \ |[SNTP=sntp,]SNT=snt...[,IDLEP=idlep] |

| | |SNTP=sntp...,SNT=snt[,IDLEP=idlep] | | |NTCOI:+SNTP=sntp,SNT=snt,EQLEV=eqlev,PROT=prot[,IDLEP=idlep] +,SNTV=sntv; | | |SNTP=sntp,SNT=snt[,MODE=mode][,PROT=prot][,IDLEP=idlep]| | | |EXTP=extp,SNT=snt[,MG=mg] | \ /

1.2 Parameters

EQLEV=eqlev Equipping level

This parameter is only intended for Switching Network Terminal (SNT) with Subordinate SNTs and protection.

For value range, see the Application Information for SNT-owning block. EXTP=extp External Hardware Connection Point

This parameter is only intended for the connection of SNT to External Hardware Switch.

If the SNT-owning block supports parameter MG then the EXTP parameter value has to be written within quotation marks.

For string range, see the Application Information for SNT-owning block. IDLEP=idlep Idle pattern

For value range, see the Application Information for block SNTH.MG=mg Media Gateway

This parameter is only intended for the connection of SNT to External Hardware Switch.Text string 1 - 7 characters

MODE=mode Mode

This parameter is only intended for the connection of DL34 SNTs.

For value range, see the Application Information for SNT-owning block. PROT=prot Protection

This parameter indicates if equipment protection is used.

This parameter is only intended for SNT with Subordinate SNTs and protection.

For value range, see the Application Information for SNT-owning block. SNT=snt Switching network terminal

Expressed as snt-n where:

snt Switching network terminal typeIdentifier 1 - 13 characters

n Switching network terminal numberNumeral 0 - 65535

The maximum value of the switching network terminal number is determined by Size Alteration Event (SAE) in the SNT-owning block (SAE 529).

For alternative expressions, see the Application Information for block TRAN and the relevant SNT-owning block.

SNTP=sntp Switching network terminal connection point

Expressed as a-b-c where:

a Switch unit nameIdentifier 1 - 7 characters

b Switch unit number

c Switching network terminal point

See Application Information for block TRASAD.

Expressed as a-b-f or a-d-e-f where:

a Switch unit nameIdentifier 1 - 7 characters

b Switch unit number

d Switch unit row number

e Switch unit column number

f Digital link number

See Application Information for block SNTHSNTV=sntv Switching network terminal variant

For value range, see the Application Information for SNT-owning block.

2 Function

This command connects a Switching Network Terminal (SNT) to a Group Switch (GS), a Subscriber Switch (SS), or an External Switch. For SNTs with subordinate

SNTs or SNTs to be connected to an external switch, one SNT can be connected in one command issue. For SNTs of any other type, the maximum of 32 SNTs can be connected. For an SNT with several hardware connections to the GS, the connection is made in consecutive order according to the designations of these connections.

For DL3 SNTs with subordinate SNTs the number of the subordinate SNTs to be connected are indicated by parameter EQLEV. Also the equipment protection can be specified for this type of SNT with parameter PROT .

For DL34 SNTs with subordinate SNTs, the number of Multiple Points (MUPs) to be reserved by the GS is indicated by parameter MODE.

For SNTs connected to an External Switch, parameter SNTP is not allowed. Parameter EXTP should be used instead indicating the connection point (port) of the External Hardware Switch. If this SNT supports connection to a Media Gateway (MG), parameter MG should be used indicating the MG name.

Parameter IDLEP may be specified only when this parameter is supported by the specified SNTs.

Note: Three adaptation blocks exist in the AXE, SNTPCD, SNTET and SNTMJ. These are used to connect device types which are not SNT owners. For SNTs connected in adaptation blocks, the SNT type is defined when the first SNT of that type is connected. This is not specified in a separate parameter but is implicit in the command.


3 Examples

3.1 Example 1

NTCOI:SNT=SNTPCD32-2,SNTP=TSM-1-2,SNTV=5;

The SNT of type SNTPCD 32, variant 5 and individual 2 is connected to the SNT connection point 2 in Time Switch Module (TSM) 1.

3.2 Example 2

NTCOI:SNT=ET1-0,SNTV=1;

The SNT of type ET1, variant 1 and individual 0 is connected to the SNT connection.

3.3 Example 3

NTCOI:SNTP=TSM-12-3&&-4,SNT=ASAM-0,SNTV=1;

The SNT of type ASAM, variant 1 and individual 0 is connected to the SNT connection points 3 and 4 in TSM 12.

3.4 Example 4

NTCOI:SNTP=TSM-1-0,SNT=SNTETET8-2&&-4,SNTV=2;

The SNTs of type SNTETET8, variant 2, with individuals 2, 3, and 4 are connected in consecutive order to the SNT connection points 0,1 and 2 in TSM 1.

3.5 Example 5

NTCOI:SNTP=TSM-8-13,SNT=SNTETET8-2&&-6,SNTV=2;

The SNTs of type SNTETET8, variant 2, with individuals 2,3 and 4 are connected in consecutive order to the SNT connection points 13,14 and 15 in TSM 8. Since connection position 15 is the last position in TSM 8, the sequence continues in TSM 9. Therefore individuals 5 and 6 are connected to connection points 0 and 1 in TSM 9.

3.6 Example 6

NTCOI:SNT=ET155-2,SNTP=TSM-1-0,SNTV=1,EQLEV=1,PROT=1;

The SNT ET155, individual 2 of variant 1 is connected to the TSM 1. The EQLEV parameter indicates that one SUBSNT is connected to the switch. Also that the SNT has equipment protection is defined.

3.7 Example 7

NTCOI:SNT=ET155-3,SNTP=TSM-1-0,SNTV=1,EQLEV=3,PROT=3;

The SNT ET155, individual 3 of variant 1, is connected in consecutive order to the TSM 1, 2 and 3. The EQLEV parameter indicates that three subordinate SNTs are connected to the switch. Also that the SNT has equipment protection is defined.

3.8 Example 8

NTCOI:SNT=MBTRCS-0,SNTP=TSM-0-0&TSM-1-0,SNTV=1;

The SNT MBTRCS, individual 0 of variant 1, is connected to TSM 0 and TSM 1 at the same connection point of both TSMs (0 in this example).

3.9 Example 9

NTCOI:SNT=VET-2, EXTP=32-4-8-5, SNTV=0;

The VET SNT, individual 2 of variant 0 is connected to an external hardware connection point which is positioned in subrack 32 in slot 4 on subport 5 of port 8.

3.10 Example 10

NTCOI:SNTP=MUX3-8-4,SNT=SNTETET8-2&&-6,SNTV=2,IDLEP=1;

The SNTs of type SNTETET8, variant 2, with individuals 2 to 6, are connected in consecutive order to the access points 4,5,6,7 and 8 in MUX3 8.

3.11 Example 11

NTCOI:SNT=ET155-2,SNTP=XM-1-2-8,SNTV=1,MODE=128,PROT=1;

The SNT ET155, individual 2 of variant 1 is connected to the XM in row 1 and column 2. The number of MUPs to be allocated by the GS for this SNT is specified in parameter MODE. Also equipment protection for the SNT is defined.

3.12 Example 12

NTCOI:EXTP="28-2-5-3",SNT=VET-1,MG=AXDWA,SNTV=0;

The VET SNT, individual 1 of variant 0, is connected to an external hardware connection point of the MG AXDWA which is positioned in subrack 28 in slot 2 on subport 3 of port 5.

47. Khi to v test cc SNT:

1.1 Command

NTTEI:SNT=snt [,SUBSNT=subsnt];

1.2 Parameters

SNT=snt Switching Network Terminal (SNT)


snt SNT typeIdentifier 1 - 13 characters

n SNT numberNumeral 0 - 65535

The maximum value of the SNT number, is determined by the Size Alteration Event (SAE) in the SNT owning block (SAE 529).

For alternative expressions, see the Application Information for block TRAN and the relevant SNT owning block.

SUBSNT=subsnt Subordinate switching network terminal

For value ranges, see the Application Information for the relevant

SNT owning block.

2 Function

This command initiates testing of a manually blocked SNT or a subordinate SNT. When an SNT with subordinate SNTs is specified in the command, only the specified subordinate SNTs are tested. Otherwise, the complete SNT is tested.

Result printout SWITCHING NETWORK TERMINAL TEST RESULT is received.


3 Examples

3.1 Example 1

NTTEI:SNT=SNTPCD32-9;

SNT 9 of type PCD32 is tested.

3.2 Example 2

NTTEI:SNT=SNTETBT4-2;

SNT 2 controlled by device block BT4 is tested.

3.3 Example 3

NTTEI:SNT=ET155-4,SUBSNT=3;

Subordinate SNT 3 of ET155 SNT 4 is tested.

48. Deblock cc SNT:

1.1 Command

/ \ |snt... |NTBLE:SNT=+ +; |snt [,SUBSNT=subsnt...]| \ /

49. XM bi block:

1.2 Parameters

SNT=snt Switching Network Terminal (SNT)


snt Switching network terminal typeIdentifier 1 - 13 characters

n Switching network terminal numberNumeral 0 - 65535

The maximum value of the switching network terminal number, is determined by the Size Alteration Event (SAE) in the SNT owning block (SAE 529).

For alternative expressions, see the Application Information for block TRAN and the relevant SNT owning block.

SUBSNT=subsnt Subordinate switching network terminal

For value ranges, see the Application Information for the relevant SNT owning block.

2 Function

This command deblocks an SNT or a subordinate SNT. When an SNT with subordinate SNTs is specified in the command, only the specified subordinate SNTs are deblocked. Otherwise, the complete SNT is deblocked.

A maximum of 128 SNTs or 1 SNT with SUBSNTs or specified SUBSNTs, can be specified in one command issue.

The supervision is activated for the entire deblocked SNT, or for the deblocked subordinate SNT.

Result printout SWITCHING NETWORK TERMINAL DEBLOCKING RESULT is received.


3 Examples

3.1 Example 1

NTBLE:SNT=SNTETBT3-18&&-21;

SNT of type SNTETBT3 with individuals 18, 19, 20, and 21 are manually deblocked.

3.2 Example 2

NTBLE:SNT=ET6-27&&-29;

SNT of type ET6 with individuals 27, 28, and 29 are manually deblocked.

3.3 Example 3

NTBLE:SNT=ET155-0,SUBSNT=0&&3;

Subordinate SNT 0, 1, 2, and 3 of ET155 SNT 0 are manually deblocked.

3.4 Example 4

NTBLE:SNT=ET155-0&&-2;

SNT of type ET155 with individuals 0, 1, and 2 are manually deblocked.

3.5 Example 5

NTBLE:SNT=ET155-10,SUBSNT=1&5;

Subordinate SNT 1 and 5 of ET155 SNT 10 are manually deblocked.

1.1 Command / / / \ \ \ | |UNIT=unit...|,DETAIL| | |GDSTP|:+ \ / + |; | |TYPE=type | | \ \ / /

1.2 ParametersDETAIL Detailed printoutTYPE=type Type of Distributed Group Switch unit to be printedUNIT=unit Distributed Group Switch unit identifier

Expressed as clm-n, mux-p-n, or xm-p-r-c where:

c Individual column number

clm Clock module name

mux Multiplexer unit name

n Unit number

p Plane identifier

r Individual row number

xm Switch matrix unit name

A Plane A

B

Plane B

Note: See Application Information for block GIOH and each unit specific AI.

2 Function

This command prints the state of Distributed Group Switch units.

The command accepts the specification of a single unit, multiple units of varying types, all units of a particular type, or all units in the Distributed Group Switch.

If parameter TYPE is specified, the state of all the Distributed Group Switch units of the type specified in the command are printed.

Repetition is allowed for all unit types.

For switch matrix units, repetition is only allowed on the column identifier.

When a range of units is specified and if no units are connected to the Distributed Group Switch in the given range then NONE is printed. Otherwise, only the state of the units that are connected are printed.

If parameter DETAIL is specified, the states of the whole chain of downstream Distributed Group Switch units connected to the units specified in the command are printed. It is not allowed to specify a Clock unit together with parameter DETAIL.

The answer printout DISTRIBUTED GROUP SWITCH STATE is received.


1.1 CommandGDBLI:UNIT=unit;

1.2 ParametersUNIT=unit Distributed Group Switch unit

Expressed as clm-n, mux-p-n, or xm-p-r-c where:


clm Clock Module (CLM) name


n Unit number

p Plane identifier

A Plane A

B Plane B


xm Switch Matrix (XM) unit name

See Application Information for block GIOH and each unit specific AI (CLM, MUX3, MUX34, MUXSP , MUXTS, XM).

1.3 Dialogue ParametersNO; Manual blocking of the specified CLM is not to take place.YES; Manual blocking of the specified CLM unit is to take place.

2 Function

This command initiates blocking of a unit in the Distributed Group Switch, provided the blocking will not result in traffic restrictions.

Result printout DISTRIBUTED GROUP SWITCH UNIT BLOCKING RESULT is received.

Manual blocking of automatically blocked units is always permitted, but not in units which are not connected.

Manual blocking of a CLM means considerable risk for the exchange as there are only two CLMs in the Distributed Group Switch. For this reason unnecessary blocking must be avoided. In the case of an unnecessary blocking attempt on a CLM, the dialogue procedure starts and answer printout WARNING, ACCEPTANCE MEANS CONSIDERABLE RISK FOR THE WHOLE EXCHANGE, ANSWER WITH YES IF YOU WANT TO CONTINUE will be received. Indicate with YES if the blocking is to be executed. Indicate with NO if the blocking is not to be executed, and the printout BLOCKING ORDER CANCELLED will be received.

An observation alarm DISTRIBUTED GROUP SWITCH UNIT MANUALLY BLOCKED indicating that the unit is now blocked is added in the alarm list.

If the alarm DISTRIBUTED GROUP SWITCH FAULT is present for the unit being manually blocked, then the fault alarm is ceased.

This command cannot be given immediately after an initial start or if the switch type is not initiated.


1.1 CommandGDBLE:UNIT=unit;

1.2 ParametersUNIT=unit Distributed Group Switch unit identifier

Expressed as clm-n, mux-p-n or xm-p-r-c where:


clm Clock Module (CLM) name


n Unit number

p Plane identifier

A Plane A

B Plane B


xm Switch Matrix (XM) unit name

See Application Information for block GIOH and each unit specific AI (CLM, MUX3, MUX34, MUXSP , MUXTS, XM).

2 Function

This command ends the blocking of a unit in the Distributed Group Switch.

Result printout DISTRIBUTED GROUP SWITCH UNIT DEBLOCKING RESULT is received.

An observation alarm DISTRIBUTED GROUP SWITCH UNIT MANUALLY BLOCKED indicating that the unit was blocked is no longer in the alarm list.

This command cannot be given immediately after an initial start or if the switch type is not initiated.


3 Examples

3.1 Example 1GDBLE:UNIT=CLM-1;

This command ends the blocking of CLM unit 1.

3.2 Example 2GDBLE:UNIT=MUX3-B-2;

This command ends the blocking of the Digital Link version 3 Multiplexer (MUX3) in plane B, unit 2.

3.3 Example 3GDBLE:UNIT=MUX34-A-3;

This command ends the blocking of the Digital Link adaptable from version 3 to 4 Multiplexer (MUX34) in plane A, unit 3.

3.4 Example 4GDBLE:UNIT=MUXSP-B-1;

This command ends the blocking of the Multiplexer based on Space Switch Module (MUXSP) in plane B, unit 1.

3.5 Example 5GDBLE:UNIT=MUXTS-A-2;

This command ends the blocking of the Multiplexer based on Time Switch Module (MUXTS) in plane A, unit 2.

3.6 Example 6GDBLE:UNIT=XM-B-1-4;

This command ends the blocking of XM in plane B, row 1, column 4.

50. Xem RP/EM:

1.1 Command / \ |DEV=dev... | | | | / \ |RADRP:+ |dety...| +; |DETY=+ +[,PPS]| | |ALL | | | \ / | \ /

1.2 ParametersDETY=dety Device type ALL All device typesDEV=dev DevicePPS Pre-Post Service If this parameter is given, then data is printed only for devices in Pre-Post Service State. If the parameter is omitted, then data is printed only for devices not in Pre-Post Service State.

2 FunctionThe command orders a printout of device RP/EM data.The printout DEVICE RP/EM DATA IN BSC is received forspecified devices, all devices of a device type, or alldevices.If the parameter PPS is specified in the command, thenonly devices which are in Pre-Post Service State will beincluded on the printout.If the parameter PPS is omitted, when only devices whichare not in Pre-Post Service State will be included onthe printout.Up to sixteen (16) such commands may be given simultaneously.All DEVICE RP/EM DATA IN BSC printouts are interruptedand terminated on commencement of an EXCHANGE DATA command,to prevent the possibility of out-of-date printouts beingobtained.The order does not remain after system restart.

50. Lnh pint v tng sae:

1.1 Command

/ \ / / \\|sae| | |block||

SAAEP:SAE=+ + |,BLOCK= + +|;|ALL| | |ALL ||\ / \ \ //

1.2 Parameters

BLOCK=block Block name Identifier 1 - 7 characters

ALL All loaded blocksSAE=sae Size Alteration Event Numeral 0 - 8192 The maximum value is defined in the Operating System Area as highest usable SAE number.

ALL All defined SAEs

2 FunctionThis command is used to print file size information of Size Alteration Events (SAEs) defined in the system.The parameter SAE specifies the Size Alteration Eventnumber. The SAE type can be local or global. The tableindicates the number range for local and global SAEs:

Table 1 SAE Type SAE number rangeGLOBAL 0 - 499LOCAL 500 - 899GLOBAL 900 - highest usable SAE number defined in the Operating System

AreaIf the SAE number specified in parameter SAE is oftype LOCAL, the parameter BLOCK must also be specified.If value ALL is specified for parameter BLOCK then file size information of the specified LOCAL SAE inall participating blocks are printed.If the SAE number specified in parameter SAE is oftype GLOBAL, the parameter BLOCK must not be specified.If parameter value ALL is specified for parameter SAEthen file size information of all SAEs defined in thesystem are printed. If a block name is specified togetherwith ALL for parameter SAE, then all SAEs defined in thespecified block are printed.The function uses the SAE database tables where all SAEs that are defined in the system are stored. If theSAE database tables are not complete, the function allowsfile size information of one SAE to be printed.The order does not remain after system restart.

3 Examples

3.1 Example 1

SAAEP:SAE=4;This command prints file size information ofof Global SAE 4.

3.2 Example 2

SAAEP:BLOCK=RE,SAE=513;This command prints file size information ofLocal SAE 513 participated by block RE.

3.3 Example 3

SAAEP:BLOCK=RE,SAE=ALL;This command prints file size information ofall SAEs participated by block RE.

3.4 Example 4

SAAEP:SAE=500,BLOCK=ALL;This command prints file size information ofLocal SAE 500 in all participating blocks.

3.5 Example 5

SAAEP:SAE=ALL;

3 Examples

3.1 Example 1RADRP:DEV=RXTRA-1;Printout device RP/EM data for device RXTRA-1.

3.2 Example 2RADRP:DEV=RXTRA-33&&-47;Printout device RP/EM data for devices RXTRA-33 toRXTRA-47 inclusive.

3.3 Example 3RADRP:DETY=RXTRA,PPS;Printout device RP/EM data for all RXTRA-devices inPre-Post Service State.

3.4 Example 4RADRP:DETY=ALL;Printout device RP/EM data for all devices not inPre-Post Service State.L i: FAULT CODE 6INVALID DEVICE TYPE SPECIFIEDdetails Command not permitted for this device type.FAULT CODE 7DEVICE TYPE DOES NOT HAVE PPS FUNCTIONdetails Device type does not have the Pre-Post Service state function associated with it.FAULT CODE 18NO DEVICE DATA AVAILABLE FOR OUTPUTdetails No device data available for output.FAULT CODE 29DATA CHANGE IN PROGRESS Command not allowed, data change command in progress.51. Tng SAE t ng:

1.1 Command

SAALI;

1.2 Parameters

-

2 FunctionCommand SAALI orders the execution of the Size AlterationEvents in the Size Alteration Action List.The command is terminated if the Automatic Size AlterationState is set Passive.The order remains after system restart.

3 Examples

3.1 Example 1

SAALI;The Size Alteration Events in the Size Alteration ActionList are executed.52. Khai BPCs:

1.1 Command /RLBDC:CELL=cell[,CHGR=chgr]+[,NUMREQBPC=numreqbpc] \ [,NUMREQEGPRSBPC=numreqegprsbpc] [,NUMREQCS3CS4BPC=numreqcs3cs4bpc] \ [,TN7BCCH=tn7bcch]+; /

1.2 ParametersCELL=cell Cell designation


Numeral 0 - 15 NUMREQBPC=numreqbpc Number of required BPCs

This parameter indicates the number of required Basic Physical Channels (BPCs) in a channel group. The parameter value must be specified as a multiple of 8.

Numeral 8 - 128

SYSDEF System defined limitNumber of BPCs is defined by the number of frequencies in the channel group.

NUMREQCS3CS4BPC=numreqcs3cs4bpc Number of required GPRS CS-3 or CS-4 BPCs

This parameter indicates the number of required BPCs in a channel group that can support General Packet Radio Service (GPRS) CS-3 or CS-4.Numeral 0 - 128

NUMREQEGPRSBPC=numreqegprsbpc Number of required EGPRS BPCs

This parameter indicates the number of required BPCs in a channel group that can support Enhanced General Packet Radio Service (EGPRS).Numeral 0 - 128

TN7BCCH=tn7bcch TN7 on BCCH frequency

This parameter indicates if Timeslot Number (TN) 7 on the Broadcast Control Channel (BCCH) frequency can be configured with Traffic Channels (TCHs) supporting EGPRS or GPRS only.

EGPRS TN7 on the BCCH frequency can be configured with TCHs supporting EGPRS.

GPRS TN7 on the BCCH frequency can be configured with TCHs supporting GPRS only.

2 Function

This command defines the number of required BPCs, and how many of the required BPCs that can support EGPRS or GPRS CS-3 or CS-4. It also defines if TN7 on the BCCH frequency can be configured with TCHs supporting EGPRS or GPRS only.

The number of TCHs for a channel group can be calculated by subtracting the BPCs used for control channels from the number of required BPCs. If the number of required BPCs is set to system defined, the number of required BPCs is equivalent to the number of defined frequencies times eight. An extended range cell only configures half of the BPCs.

There must be at least one frequency defined per eight number of required BPCs.

It is not allowed to set the number of required BPCs so that the Stand-alone Dedicated Control Channels (SDCCH/8s) set in command RLCCC cannot be configured.

The number of SDCCH/8s and the number of required BPCs that can support EGPRS or GPRS CS-3 or CS-4 cannot exceed the number of required BPCs in the channel group.

The parameter TN7BCCH is only valid for channel group 0.

If channel groups have been defined for the cell using command RLDGI, then the CHGR parameter is mandatory.

The command is not valid for external cells, that is, cells belonging to another Base Station Controller (BSC).


3 Examples

3.1 Example 1RLBDC:CELL=HLM1,NUMREQBPC=8;

The required number of BPCs for the cell HLM1 is set to 8.

3.2 Example 2RLBDC:CELL=HLM1,CHGR=1,NUMREQBPC=16;

The required number of BPCs in channel group 1 in cell HLM1 is set to 16.

3.3 Example 3RLBDC:CELL=HLM1,CHGR=1,NUMREQBPC=SYSDEF;

The required number of BPCs in channel group 1 in cell HLM1 is set to the number of BPCs defined by the number of frequencies in the channel group.

3.4 Example 4RLBDC:CELL=HLM1,CHGR=1,NUMREQBPC=16,NUMREQCS3CS4BPC=4;

The required number of BPCs in channel group 1 in cell HLM1 is set to 16. The required number of BPCs that support GPRS CS-3 or CS-4 in channel group 1 in cell HLM1 is set to 4.

3.5 Example 5RLBDC:CELL=HLM1,CHGR=0,NUMREQBPC=16,NUMREQEGPRSBPC=4,TN7BCCH=EGPRS;

The required number of BPCs in channel group 0 in cell HLM1 is set to 16. The required number of BPCs that support EGPRS in channel group 0 in cell HLM1 is set to 4. TN7 on the BCCH frequency can be configured with TCHs supporting EGPRS.

53. L nh dng Tng BPCs:

RLBDC:CELL=cell[,CHGR=chgr]+[,NUMREQBPC=numreqbpc] \ [,NUMREQEGPRSBPC=numreqegprsbpc] [,NUMREQCS3CS4BPC=numreqcs3cs4bpc] \ [,TN7BCCH=tn7bcch]+; /

1.2 ParametersCELL=cell Cell designation


Numeral 0 - 15 NUMREQBPC=numreqbpc Number of required BPCs

This parameter indicates the number of required Basic Physical Channels (BPCs) in a channel group. The parameter value must be specified as a multiple of 8.Numeral 8 - 128

SYSDEF System defined limitNumber of BPCs is defined by the number of frequencies in the channel group.

NUMREQCS3CS4BPC=numreqcs3cs4bpc Number of required GPRS CS-3 or CS-4 BPCs

This parameter indicates the number of required BPCs in a channel group that can support General Packet Radio Service (GPRS) CS-3 or CS-4.Numeral 0 - 128

NUMREQEGPRSBPC=numreqegprsbpc Number of required EGPRS BPCs

This parameter indicates the number of required BPCs in a channel group that can support Enhanced General Packet Radio Service (EGPRS).Numeral 0 - 128

TN7BCCH=tn7bcch TN7 on BCCH frequency

This parameter indicates if Timeslot Number (TN) 7 on the Broadcast Control Channel (BCCH) frequency can be configured with Traffic Channels (TCHs) supporting EGPRS or

GPRS only.

EGPRS TN7 on the BCCH frequency can be configured with TCHs supporting EGPRS.

GPRS TN7 on the BCCH frequency can be configured with TCHs supporting GPRS only.

2 Function

This command defines the number of required BPCs, and how many of the required BPCs that can support EGPRS or GPRS CS-3 or CS-4. It also defines if TN7 on the BCCH frequency can be configured with TCHs supporting EGPRS or GPRS only.

The number of TCHs for a channel group can be calculated by subtracting the BPCs used for control channels from the number of required BPCs. If the number of required BPCs is set to system defined, the number of required BPCs is equivalent to the number of defined frequencies times eight. An extended range cell only configures half of the BPCs.There must be at least one frequency defined per eight number of required BPCs.It is not allowed to set the number of required BPCs so that the Stand-alone Dedicated Control Channels (SDCCH/8s) set in command RLCCC cannot be configured.The number of SDCCH/8s and the number of required BPCs that can support EGPRS or GPRS CS-3 or CS-4 cannot exceed the number of required BPCs in the channel group.

The parameter TN7BCCH is only valid for channel group 0.

If channel groups have been defined for the cell using command RLDGI, then the CHGR parameter is mandatory.

The command is not valid for external cells, that is, cells belonging to another Base Station Controller (BSC).


3 Examples

3.1 Example 1RLBDC:CELL=HLM1,NUMREQBPC=8;

The required number of BPCs for the cell HLM1 is set to 8.

3.2 Example 2RLBDC:CELL=HLM1,CHGR=1,NUMREQBPC=16;

The required number of BPCs in channel group 1 in cell HLM1 is set to 16.

3.3 Example 3RLBDC:CELL=HLM1,CHGR=1,NUMREQBPC=SYSDEF;

The required number of BPCs in channel group 1 in cell HLM1 is set to the number of BPCs defined by the number of frequencies in the channel group.

3.4 Example 4RLBDC:CELL=HLM1,CHGR=1,NUMREQBPC=16,NUMREQCS3CS4BPC=4;

The required number of BPCs in channel group 1 in cell HLM1 is set to 16. The required number of BPCs that support GPRS CS-3 or CS-4 in channel group 1 in cell HLM1 is set to 4.

3.5 Example 5RLBDC:CELL=HLM1,CHGR=0,NUMREQBPC=16,NUMREQEGPRSBPC=4,TN7BCCH=EGPRS;

The required number of BPCs in channel group 0 in cell HLM1 is set to 16. The required number of BPCs that support EGPRS in channel group 0 in cell HLM1 is set to 4. TN7 on the BCCH frequency can be configured with TCHs supporting EGPRS.

54. Li ABIS PATH UNAVAIL: 117. Note:

In this result an ABIS PATH UNAVAIL(khong san co, khong co gia tri) fault may be received, this fault is also covered(che boi) by this OPI

Alarm ceasing printout:RADIO X-CEIVER ADMINISTRATION MANAGED OBJECTS IN TRANSCEIVER GROUP MANUALLY BLOCKED

1.1 CommandRXAPI:MO=mo,DEV=dev...,DCP=dcp...[,RES64K];

1.2 ParametersDCP=dcp Digital connection point number used as termination point in the Base

Transceiver Station (BTS) for the Abis pathNumeral 0 - 511

DEV=dev Transmission device used for the Abis path

See Application Information for block TRAN for the format and value range of this parameter.

MO=mo Managed object instance

See Application Information for block RXCTA for the format and value range of this parameter.

The Managed Object (MO) must be of class Transceiver Group (TG).RES64K A 64 kbit/s Abis path will be reserved for use by a suitably configured Time

Slot (TS) only.

2 Function

This command is used to define one or more Abis paths between the Base Station Controller (BSC) and the Base Transceiver Station (BTS).

Up to 124 Abis paths may be defined per TG. All Abis paths within a TG must be connected to devices of the same transmission type. See Application Information for block RBLT for valid transmission types.

Warning!

The setup of the transmission type must be considered when defining Abis paths as they may already be used by the transmission system for control purposes.

The first specified DEV argument is connected to the first specified DCP argument and the second specified DEV argument is connected to the second specified DCP argument, etc.

The answer printout RADIO X-CEIVER ADMINISTRATION ABIS PATH RESULT will show the results of the Abis path definition request.


3 Examples

3.1 Example 1RXAPI:MO=RXOTG-1,DEV=RBLT-1,DCP=1;

An Abis path is defined in BTS logical model G12 between the transmission device RBLT 1 and DCP 1 within TG 1.

3.2 Example 2RXAPI:MO=RXOTG-3,DEV=RBLT-2&&-4,DCP=4&&6;

Abis paths are defined in BTS logical m

85557446 Tong Hop Lenh Ericsson

Documents

Transcript of 85557446 Tong Hop Lenh Ericsson