800-238-7514 Info...It replaces Dynatel Subscriber Loop Analyzer 965DSP. The 965AMS has a bigger,...

E-1

Wire FinderLocates path of wires behind walls, in ceilings and underground. Use on energized or de-energized wires up to 120 VAC. Capable of locating a specific circuit breaker, pinpointing ends of

terminated wires or measuring depth up to 3'.Part No. 508S

Long Range Wire LocatorPortable locating system including a Transmitter, Inductive Coupler, Inductive Antenna and Receiver. Built in antenna allows locating in remote areas. Operates on dead or active lines.

No earth grounds required in most situations. Silent RF locating tone minimizes interference to other circuits.Part No. 501

Wire SorterEasily sorts up to six single or six pair of unpowered wires with or without a known ground path. Quickly identifies unmarked wiring. Locates proper wiring in bundled groups. Works on non-energized circuits. Includes TL-65

lead set. From Ideal Industries.Part No. 61530

Shielded Modular JacksLinkMaster™ UTP/STP tester with one remote. From Ideal Industries.Part No. 62200

TelScout® TS90 TDRCable tester for telephone applications

Finds faults on telephone twisted pair cable. Designed specifically for telephone local loop applications.Two pair test capability15km fault location capability

Pair comparison and splits/crosstalk modesIntermittent fault locationMeasures distance to fault in feet, meters or timeConfigurable for any cable type and Vp (0.3 to 1)

From Tempo.Part No. TS90

••

••••

TelScout® TS100 TDRFinds faults on telephone twisted pair cable. Designed specifically for telephone local loop applications. Two pair and coax testing in a single unit (optional).15km fault location capability

Short pulse width option (includes coax testing capability)Pair comparison and splits/crosstalk modesIntermittent fault locationMeasures distance to fault in feet, meters or timeConfigurable for any cable type and Vp (0.3" to 1")Internal storage for 20 waveforms and notes

From Tempo.Part No. TS10001

Voice Cabling/Phone SystemsPart No. 33864 - Tone and Probe KitPart No. 62094 - Tele4™ Modular Adapter, Banjo Adapter for Voice CircuitsPart No. 62180 - ABS™ and Probe Tester, Dial Tone Monitoring

Smart6™ Modular AdapterReverse-wire adapter designed for voice circuit testing. LED indicators for polarity, jack addresses and incom-ing call identification. Test button allows testing of pair one or two for

power. Easy-to-read label identifies individual conduc-tors and pins with number, color and polarity. Sturdy stainless steel belt clip. From Ideal Industries.Part No. 62096

Data8™ Modular AdapterAdapter with straight-through wiring tests T568A, T568B, 10Base-T, Token Ring and TP-PMD systems. Use with tone generators, butt-in test sets and other devices to access data

lines without service interruption. Features TIA/EIA Category 5 jacks and a unique internal circuit design to reduce attenuation, coupling and NEXT. May be placed as a coupler in a Category 5 link without exceeding acceptable NEXT values for link certification. From Ideal Industries. Part No. 62098

•

••

•••••

6209462094

Test Equipment - Copper

[email protected] 800-238-7514

E-2

Modular AdapterProvides a quick connect to modular telephone jacks using any standard butt-in test set equipped with spring clips. Part No. 10113000

In-Line Modular AdaptersDesigned to permit testing on working lines. Allows circuit access without disconnecting equipment. Line Cords, accessories and replacement components available.Part No. 10210100 - 4-wirePart No. 10220100 - 6-wirePart No. 10230100 - 8-wire

Sidekick® Twisted Pair TesterLightweight, handheld meter that quickly and accurately uncovers intermittent troubles. Identifies faults in locations ranging from outside plant cable to inside wiring, and from closures to connecting blocks.

Measures resistance, AC/DC volts and capacitive kickProvides tone for twisted pair or crossed conductor identificationSingle setup for testing Tip-Ring, Tip-Ground and Ring-GroundMinimal drying effect in all rangesField replaceable leadsLow-battery indicator light

From Tempo.Part No. 11345029 - Sidekick 7BPart No. 11375002 - Sidekick T&N: Loop Current 0-100mA, Circuit Noise 0-75 dBrnC, Circuit Loss -15 to +1 dB, Power Influence 50-100 dBrnC

•

•

•

•••

VDV Multimedia Cable Tester KitAn easy-to-use cable testing and verifica-tion device that can quickly test all wiring requirements found throughout today’s residential and commercial environments. Tests for opens, shorts, miswires, reversalsand split pairs and also identifies cable voltages. Can support additional optional remotes, making it efficient for one person testing.

Voice – Tests 3-pair USOC and 6-position RJ-11/12 jacks for voice cable testingData – Tests both shielded and unshielded, cable testing to T568A/B (RJ-45)Video – Tests coax cable for opens and shorts with F-Connector interface

From Ideal Industries.Part No. 33856

TS®90 Cable Fault FinderINSTANTLY finds opens and shorts, with a capability of up to 2,500'Measure length of cable on a spool – great for inventory managementSend tone – includes SmartTone™, a tone generator offering five different tones - short the far end of the correct pair and the tone will change to allow

you to identify your pair with certainty.From Fluke Networks.Part No. 2327758

TS®100 Cable Fault FinderMonitor cable inventory in trucks and warehousesGenerate accurate bids by quickly assessing needsMeasure remaining cable on open spools up to 3,000'Find and fix cable troubles without pulling new wire or blindly cutting into walls or streets

From Fluke Networks.Part No. 2327747

•

•

•

•

•

•

•

•

•

•



E-3

NAVITEK™ Active LAN TesterOptimized for passive and active structured data cable network testing, the NAVITEK gives you step-by-step network troubleshooting responsiveness.Comprehensive testing and

troubleshooting tool for structured data networksVerifies the integrity of the physical network and validates active network connectivity with PING and Hub blinkingDetects port services such as Ethernet, ISDN, POTS and Token RingDisplays Ethernet network speed and capabilitiesPerforms length measurement up to 1500 feet (457.2 meters)Tests both shielded and unshielded structured cable to T568A/B standards with fault identificationSupports four-tone generation for cable tracing Easy-to-read backlit LCD display


Tel-Line Tester™

Plugs into 5-pin connector blocks to isolate the Central Office from the field at SLC Remotes, building entrances and Central OfficesLook IN or OUT with butt sets or voltmetersFollow the Bell System Practice

(BSP). Close out troubled line and pull next job ticket when using Craft Access terminal.

From Westek.Part No. TCTLTS1A - Tester unit onlyPart No. TCTLTS2 - Tester, looping plug and craft access wall cord

SecuriTEST™ CCTV/Security TesterSix essential CCTV tools in one

Combines a CCTV video tester, PTZ camera controller, Digital Multi-meter, UTP cable tester, video test pattern generator and PTZ protocol analyzer in a single compact pack-age. Includes 6 AA batteries and AC

Adapter/charger. From Ideal Industries.Part No. 33891

•

•

•

••

•

••

•

•

•

Subscriber Loop Tester Ohms to distance conversionA load coil counter and ringers counter A wide range of voice band tests for twisted pair diagnosisSelf-calibrationGraphical user interface – user-friendly, icon-based display of test resultsReplaceable test leads

Backlit high resolution/high contrast LCD displayAmong the tests available are voltage, current, resistance, opens, tone, loss, noise, power influence and balance. Rugged, weather-resistant design. Housed in a light-weight, hand-held case for portability and ease of handling. Weighs only 1 lb. From 3M. Call for details.Model No. 945DSP

Dynatel™ Advanced Modular System 965AMS

The new handheld Dynatel 965AMS provides full-featured testing for the triple play services. It replaces Dynatel Subscriber Loop Analyzer 965DSP. The 965AMS has a bigger, brighter display that features 3M Vikuiti display enhancement technology, a user-friendly, icon-based, graphical user interface that requires minimial training and field-swappable modules.

The unit’s rugged, waterproof design meets or exceeds the stringent IEC-529 IP67 immersion test and five-foot drop test for reliable outdoor use in all weather conditions. The 965AMS is available with an optional ADSL2+ service interface modem module, and, in the future, will feature additional hardware and software options to support testing of VDSL2, FTTx fiber test, VoIP and other triple play technologies yet to come.

Six models available:

From 3M. Call for details.

•••

••

••

BasicTDRTDR and SA

•••

Basic and ADSL2+Basic, TDR and ADSL2+SA and ADSL2+

•••

BasicTDRTDR and SA

•••

Basic and ADSL2+Basic, TDR and ADSL2+SA and ADSL2+

•••



E-4

Qualification Tester CableIQ™ A cabling bandwidth tester for network technician.Qualifies - Sees if your existing cabling has the bandwidth to support voice, 10/100, VoIP or Gigabit EthernetShows why existing cabling cannot support the network's bandwidth requirement

Detects what's at the end of any cable and displays device configuration (speed/duplex/pairing)Identifies unused switch ports that can be reallocatedGraphically maps wiring configuration and shows distance to faults with Intelligent WiremapTests all copper cabling media: twisted-pair, coax, and audio cabling

From Fluke Networks. Call for details.

TS®19 Test SetBack-to-basics dual function test setBoth tone and pulse operationLast number redialSolid state circuitry and a high imped-ance monitor so it is also data safeFrom Fluke Networks.Part No. 2326569

TS®22 Test SetBuilt-in amplified speakerLast number redial, pause button and mute switchHands free listening, audible ringer for call backsVery rugged, waterproof constructionDropSafe™ - passes 20' drop test

Includes piercing pin cordMeets or exceeds all the specs of the TS-21


•

•

•

••

•

••••

••

•

••

••

TS®22A “Hands Free” ButtsetTwo-way speakerphone keeps both hands free to work while you are talking over the buttsetLast number redial, a pleasant ringer, a mute button, and a speed-dialing bankVery rugged, waterproof construction

DropSafe™ - passes 20' drop testIncludes piercing pin clips


TS®25D Test Set with LCDFeatures caller ID and call waiting caller IDData lockout and lockout over-ride means safety in talk or monitor mode DSL/POTS filtering technology allows you to safely draw dial tone

without downing DSLBuilt-in tone generator simplifies wire IDAmplified speaker means hands-free workTalk Battery function provides voltage to carry voice conversation on non-powered pairsCompact unit with oversized robust liquid crystal display (LCD) makes easy-to-use menus


TS®30 Test SetHigh impedance Monitor for DataSafe operation, allowing techni-cians to clip onto a line in Monitor mode without disrupting existing traffic.Hook flash buttonMute switch, last number redial, an audible ringer for callbacksVery rugged, waterproof constructionDropSafe™ - passes 20' drop testFrom Fluke Networks.

Part No. 2328041

•

•

•••

•

•

•••

•

••

••



E-5

TS®42 Deluxe Test SetDataSafe® Protection – a superior High Impedance Monitor to protect data lines in Monitor Mode. 2-way hands-free amplified speakerphone“Always-on” monitor modeLow/high voltage indication/warningErgonomic waterproof design

DropSafe™ - passes 20' drop testIncludes angled piercing pin clips


TS®44 Pro Test SetDataSafe® Pro Data Protection Technology: Featuring superior high-impedance monitoring, making you completely safe in Talk, Monitor or Override Mode.DSL/POTS Filtering Technology: A technician can butt in on a live DSL line and pull dial tone to test the POTS service without downing or disrupting

the data service. From Fluke Networks.Part No. 2329235 - Includes angled piercing pin clipsPart No. 2329247 - Includes angled bed of nails

HD-4 TesterThe HD-4 has all of the basic features needed by a technician, delivered in a low cost craft-grade design. Extremely rugged and reliable, the HD-4 model is THE value leader in basic craft-quality test sets.High Impedance “Safe For Data” Monitor Mode > 120K OhmsRugged - meets 12' and 20' drop tests

Built-in ringer to indicate incoming callsLast Number Redial - 23 digits - T/POvervoltage/Overcurrent ProtectionDTMF (tone) and Rotary (pulse) DialingLEDs for polarity indication

From HD Telecom.Part No. HD4

••••

••

•

••••••

Series 6 Test SetsThe Series 6 provides a full set of advanced features in a craft-grade design. All Series 6 models include SIGNALSHIELD™ circuit for the protection of digital/data circuits for testing POTS/analog service on DSL circuits without harming the data or being locked out. SIGNALSHIELD™ works both in talk and monitor modes.

The test sets feature two kinds of memory dialing: three “One-Touch” memory buttons on top and the ability to store 10 more numbers in speed dial. From HD Telecom

630iThe 630i is a top-of-the-line model with all of the standard features plus a SIGNALALERT™ circuit to provide an audio and visual alert, indicating the presence of digital signals, and a speakerphone for hands-free operation.Part No. HD630

620Same full set of features as the HD-630i, but without the SIGNALALERT™ circuit.Part No. HD620

610Same full feature set as the HD-630i, but without the SIGNALALERT™ circuit or speakerphone. The HD-610 includes a battery powered speaker for amplified listening in talk and monitor modes.Part No. HD610

ADSL/POTS SplitterSafely draws dial tone from anywhere on the line without disrupting ADSL service. The first hand-held splitter in the field with bridging capability – it can trouble-shoot the permanent-installed

POTS splitter at the NID without disrupting the ADSL service - remaining on-line during servicing is critical to data subscribers. It is tough, small and lightweight. Part No. 10410100





Cable Tracing KitOffers a complete signal tracing solution. Includes tone generator, amplifier probe, cable assemblies, flat tip and nylon carrying case.Part No. 33864

Tone and Probe KitIncludes high power tone test set, induc-tive amplifier and Cordura carrying case with belt loop and protective Velcro flap.Part No. 701K

CATV Cable Tone Test SetSend tone through any passive device along the cable path - through splitters, taps, directional couplers and more.Part No. 402K

Security/Alarm KitIncludes the Model 620 Loop Verifier, Model 200EP Inductive Amplifier and 700C Carrying Case for a complete toning and testing solution.Part No. 620K

Modular Cable TesterTests 258, T568A, 10BASE-T and USOC systems. Identifies opens, shorts, reversals, and transposed pairs and can send a tone to identify cable at remote locations.Part No. 468

Tone Test SetA continuous or alternating tone generator, continuity tester and volt-age tester. Equipped with a modular connector for standard telephone jacks. Generates a distinctive audio tone detectable with a handset or inductive amplifier.Part No. 77M

High Power Tone Test Set Tone generator, continuity and volt-age tester, equipped with a modular connector for standard phone jacks. Powerful enough to tone through central office battery.Part No. 77HP

Inductive AmplifierDesigned to work with any tone genera-tor to identify and trace wires within a group, without damaging insulation.

Part No. 200EP

Filter ProbeBlocks A/C interference by filtering out power related noise. For locating and identifying phone, data and computer

cabling; security and alarm circuits; HVAC and building automatic wiring, and de-energized electrical wiring.Part No. 200FP

Residential KitData T®-Cutter; UTP Stripper; Punchmaster™ with 110 Blade; Crimpmaster™ RJ-45; CATV Die Set; Stripmaster® RG-6; RG-6 Quad Shield Stripmaster® Blade; F-Connector Tool; Journeyman’s

Pouch. From Ideal Industries. Part No. 33905

E-7

Pro Residential KitJourneyman’s Pouch; Punchmaster™ 110/66 Blade; UTP Stripper; 5-in-1 Screwdriver; Probe Pic; Lever™-Snips; Data T®-Cutter; Coax Stripper; F-Connector Tool; Tone Generator; Amplifier; CATV Crimpmaster™ RJ-45 Die Set. From Ideal Industries.Part No. 33925

Technician's Service KitPunchmaster™ II Punch Down Tool with 110 blade; 66 blade Electricians Scissors with stripping notch; UTP/STP Stripper; Screwdriver; Probe Pic and Spudger; Nylon Case with Belt Clip. From Ideal Industries.Part No. 33505

Cable Service Kit Punchmaster™ with 110 blade; 66 blade only; Electricians Scissors with stripping notches; UTP/STP Stripper; 5-in-1 Screwdriver; Probe Pic and Spudger; Tone Generator;

Amplifier Probe; Journeyman’s Electricians Tote. From Ideal Industries.Part No. 33605

LinkMaster™ PRO Economy KitsPerform all test functions with one remote each for both twisted pair and coax cable in this economy kit with carrying case.Tests for shorts, opens, mis-wires, reversals, split pairs,

and shield continuity Measures length on UTP, ScTP and coax with or without remotes Identifies up to eight twisted pair and coax remotes Tone generator sends up to four different tones Test results displayed in wire map format Snap-off battery cap allows for easy battery change Two size kits with unshielded and shielded cable assemblies


•

•

•••••

LinkMaster™ PRO Tester KitEverything you need to perform all test functions for up to eight remote mapping locations on twisted pair and coax cable is included in this kit.

Kit includes:Main tester Eight twisted pair remotes Eight CATV color-coded F-Terminators Nine RJ-45 shielded jumper cables Nine RJ-11 jumper cables RJ-45 and RJ-11 adapter RJ-45 to alligator clip cable assembly RJ-11 to alligator clip cable assembly Carrying case


Electrical Contractor Telecom II Kit

Provides all the basic items need to get started in tele-communications. Electrical Contractor Telecom Test Kit I also available. Includes the TS®30 Test Set instead of the Pro2000™ Tone & Probe Kit. All other items in the kit are the same as Test Kit II.

Kit includes:Pro2000™ Tone & Probe KitD814™ Impact ToolCable Stripper Adjustable Cable Cutter/StripperProbePic ProbeElectrician’s D-Snips™

Standard Modular Adapter66/110 EverSharp™ BladeSoft-sided Zippered Case


•••••••••

••••••••



E-8

LAN Cable TesterTests up to 300 MHz exceeding the requirement for emerging Cat 6/Class E standardsPerforms all advanced Power Sum measurements up to 300 MHzSupports up to 15 different tests individually or in a test suite

Supports Distance-to-Fault with TDR technologyOptions for single mode and multimode fiber optic and talkset capabilitiesLT-Record Manager software supports all record keeping, reporting and certification requirementsEasy-to-use button interface

From Ideal Industries.Part No. LT8600TSP

LANTEK® Cable Certifier KitsLANTEK offers a family of high-perfor-mance cable certification testers to support a full range of LAN cable testing. The testers uses the IDEAL patented measure-ment system that removes the effects of ordinary patchcords, making channel and permanent link certification of a cable

standard such as Cat 6A or ISO-F possible without changing adapters. The same patented technology also makes DUALmode Testing possible. Each kit includes a case, two headsets, AC adapters and hanging straps, a serial cable and USB cable and LANTEK Reporter software.From Ideal Industries. Call for details.

LANTEK 6A Level III verified LAN certification tester designed to support up to CAT 6/ISO-E cabling. Includes soft shell case and Cat 6 universal adapters and reference cables.

LANTEK 6ADesigned to support the emerging Cat 6A Standard to certify LAN cabling to support applications up to 10G Ethernet. Kit includes a soft shell case and Cat 6A universal adapters and reference cables.

LANTEK 6A PremiumSame features as LANTEK 6A, but comes in a hard shell case. Kit also includes a PCMCIA adapter card and reader, 64MB compact-flash memory card, two extra batteries and DUAL bay rapid battery charger.

•

•

•

••

•

•

LANTEK 7GThe world’s first independently verified Level IV accu-rate LAN cable certification tester capable of testing installations up to 1 GHz, exceeding the requirements for Cat 6A/7/ISO-F. Kit includes Cat 6A and Cat 7 adapters and reference cables.

LANTEK 7G PremiumSame features at the LANTEK 7G, but comes in a hard shell case. Kit also includes a PCMCIA adapter card and reader, 64MB compact-flash memory card, two extra batteries and DUAL bay rapid battery charger.

LANTEK® 10GB Alien Crosstalk Kit Add Alien Crosstalk testing capability to any LANTEK 6A or 7G certifier. Kit includes two dual-port AXT adapters, 12 AXT terminators, shielded patch cords, manual, firmware update and PC reporting software.Unique Dual-port AXT adapter allows PSANEXT testing with just

one handset for quick initial site testing. Dual-handset mode allows complete AXT certification four times faster than other AXT test systems. No PC required in the field - all test results calculated on-the-fly for instant pass/fail indication. From Ideal Industries. Call for details.

FIBERTEK™ Advanced fiber test option for use with LANTEK products

Measures signal loss length and delay over Multimode and Single mode fiber. Enables bi-directional dual wave-length measurements for both Multimode and Single mode fiber. Talkset capability for both Multimode and Single mode fiber available for enhanced communications.

Basic and premium FIBERTEK kits available for multimode, single mode or both. Premium kits include TRACETEK™ adapter for analyzing reflections along a fiber and reports distance to events as well as magnitude. From Ideal Industries. Call for details.

Test Equipment - Copper/Fiber


Purchase of a LANTEK includesfree demo and training from Ideal!

E-9

Handheld Services Tester HST-3000A rugged unit designed for use in the field, the HST-3000 offers support for electrical and optical Ethernet testing in a single unit. The IPv6 option enables installation and troubleshooting of IPv6 networks.Modular hardware and software architec-ture is flexible and easily upgraded in the field. The unit supports Triple Play and

FTTx testing as well as TDM network testing and is a future-proof solution for circuit-switch to packet-switch migration. It is fully configurable, easy to upgrade as needs change. From JDSU. Call for details.

DTX Digital Cable Analyzers and Certification Testers

Test and certify Cat 6 cable in 12 sec-onds compared to more than 30 seconds for most other testers. In addition, the units suggest potential actions to correct the problem. Each tester's internal memory stores up to 250 graphical Cat 6 test results or up to 2,000 text reports. LinkWare software for link to a PC is included. From Fluke Networks.

DTX 1200Features a maximum testing bandwidth of 350 MHz, allowing all tests to be done in just 12 seconds in full compliance with industry standards.

DTX 1800 Features a maximum testing bandwidth of 900 MHz, allowing testing of video distribution, Class F, CATV and 10 Gigabit Ethernet cables.

Compact Optical Test Platform from JDSU

T-BERD 6000A compact, lightweight test platform for both installation and maintenance, the T-BERD 6000 offers the high levels of performance and upgradeability.

Modular in design, the unit features more than 40 different fiber modules supporting a wide range of applications, and is a single source for future fiber and photonic testing needs.Applications:

Fault LocatorOTDR and power level testingCWDM/DWDM testingPMD and spectral attenuation profileChromatic Dispersion (CD) testingInsertion Loss (IL) and Optical Return Loss (ORL) testing

T-BERD 8000The T-BERD 8000 is a field-scal-able optical test platform for both installation and maintenance. A single Transport Module provides an integrated solution for Ethernet, SONET, SDH, PDH, and T-carrier networks. Optical

Modules allow thorough testing of short-haul, long-haul, FTTx, CWDM, DWDM and ROADM networks.Applications:

OTDR and power level testing10GigE LAN and 1 GigE optical interfaces10/100/1000 Mb/s electrical Ethernet interfacesSONET/SDH testing at 51 Mb/s, 155 Mb/s, 622 Mb/s, 2.5 Gb/s and 10 Gb/sT-carrier/PDH testing at T1, E1, E3, DS3 and E4 ratesCWDM/DWDM and ROADM testing, channel isola-tor up to 12.5GbpsPMD and spectral attenuation profileLoss (IL) and Optical Return Loss (ORL) testing.Chromatic Dispersion (CD) testingOptical Spectrum Analyzers for WDM and ROADM testing

••••••

••••

•

•

••••

Test Equipment - Fiber


E-10

OptiFiber Multimode OTDR The OptiFiber integrates power/loss, fiber length measurement, OTDR analysis and fiber connector end-face imaging to provide a higher tier of fiber certification and diagnostics. The unit allows network owners of all levels to certify fiber to customer specifications and industry standards, troubleshoot

connection-rich links and document results.Features:

Diagnose and solve fiber problems with integrated ChannelMap, Auto OTDR and fiber end-face inspectionEasy-to-use interface and small, lightweight designCertify fiber using Auto OTDR analysis, automated loss and length measurements and fiber end-face inspectionEnhance visibility into premise, campus and metro networks with short event deadzonesThe companion LinkWare PC software documents, reports and manages all test data

OF-500-01 - Multimode OTDR (62.5µm accessories)OF-500-02 - Advanced multimode OTDR (62.5µm accessories)OF-500-03 - Single mode OTDRFrom Fluke Networks.

Handheld OTDRs AXS-100 SeriesThe AXS-100 series covers the whole range of short-haul OTDR test applica-tions. Featuring event dead zones and first-class dynamic ranges, it includes four models to better suit your specific OTDR testing requirements. From EXFO. Call for details.

AXS-100 Access OTDRDesigned for single mode OTDR troubleshooting, this model features an in-service PON troubleshooting option and offers the 1310, 1550 and 1625nm wavelengths, with respective dynamic ranges of 29, 28 and 28 dB.

AXS-110-SM single mode OTDRIdeal for FTTx/access and CATV testing, this model offers the 1310 and 1550nm wavelengths, with respec-tive dynamic ranges of 32 and 30 dB.

•

••

•

•

AXS-110-MM Multimode OTDROptimized for enterprise testing on both 50 and 62.5µm multimode fiber, this model offers the 850 and 1300nm wavelengths, with respective dynamic ranges of 24 and 25 dB.

AXS-110 All-Fiber OTDRCombining single mode and multimode capabilities for enterprise, campus and access networks, this model offers the 850, 1300, 1310 and 1550nm wavelengths, with respective dynamic ranges of 24, 25, 32 and 30 dB.

Optical Loss Tester AXS-200/350Features a pass/fail LED indicator and lets you set your own thresholds for loss measurements, specifically designed for first-class ease of use. The unit is ideal for FTTh deployments as well as WDM and DWDM network assessment FIP and VFL capabilities.Clear, LED-based pass/fail assessmentError-free, semi-automatic loss testing

Straightforward step-by-step loss testing wizardPlatform advantages: modularity, connectivity and a high-legibility color screenFiber inspection probe port to prevent dirty and damaged connector problemsVisual fiber location capabilities for quick and easy troubleshootingCWDM test solution ready and high power detector

From EXFO.

Fiber Certifier AXS-200/360Allows the user to easily and accu-rately perform all fiber certification and troubleshooting tasks. Optimized for various applications such as 10 Gbit/s transmission, the AXS-200/360 delivers optical loss measurements at multiple wavelengths automatically, verifies user-inputted fiber lengths, inspects

connectors with the optional fiber inspection probe (FIP) and detects breaks with the optional visual fault locator (VFL). From EXFO.

••

••

•

•

•



E-11

Advanced Cable Maintenance Test SetSidekick® Plus 1155-5000

A multifunction test tool that will improve any technician's testing and troubleshooting capabilities on twisted pair. Building on a trusted design and patented technology, this lightweight, hand-held meter quickly and accurately uncovers intermittent troubles that other test sets can't detect. It uses digital technology

to combine VOM and loop current tests, longitudinal balance (Stress Test), transmission and noise, open locator, load coil detection, RFL and a powerful TDR into one easy-to-use test set. Test functions can be selected and used individually, or run automatically by using the innovative Auto-test. From Tempo.Part No. 11555000

Cable Acceptance Testing and Fault Locating OTDR 920XC

Greenlee’s 920XC is a handheld, full-fea-tured OTDR for cable acceptance testing and fault locating. The Autotest function automatically chooses the optimal mea-surement settings, scans the fiber under test and performs fiber analysis displaying length of fiber, loss of each event in an

easy to read table. The user may also use the graphical user interface to navigate the trace signature for more detailed views of specific fiber events.

Handheld OTDR M200A full-featured OTDR weighing only 2 lbs. and designed to accept both multimode (850/1300nm) and single mode (1310/1550nm) modules for testing flexibility. Replaces popular M600 Mini-OTDR. Designed for Tier 2 testing of premise networks, FTTx PON certification and troubleshooting, fast

fault location, splice verification, network documenta-tion. From AFL Telecommunications.Part No. M200KQUAD - Single mode and multimodePart No. M200KSM - Single modePart No. M200KMM - Multimode

Model 340 OTDR Plus Multitester IISmartTest™ Function provides a fast, one-button analysis of the entire fiberAutoIncrement™ Function speeds up repetitive as-built testing in

high-fiber-count projects, saving time, money and reducing errorDualTrace™ Function shows optimal traces at both wavelengths on one graph for easy analysisLarge variety of high-performance modules available - single mode up to 46 dB offers significant distance capacity and enhances event search capabilitiesMulti-test capabilities offer all-in-one convenience on a field-upgradeable platformSoftView™ Emulation Software for batch printing and editing, trace overlay and bidirectional analysisLarge display with active matrix color eases eye-strain during periods of extended useTests both MM and SM fiber

From Corning Cable Systems.

Model 500 Optical Multi-tester Large, color display with touch screenHard buttons plus application-specific soft keysTwo platform sizes for your appli-cation optimization

Multiple powering options: Li-Ion battery or ACMultiple I/O ports for easy connection of accessories, including USB, 10/100 MB Ethernet and two PC card (PCMCIA) slotsIncludes modular CD-ROM; CD-RW upgrade availableFeatures online assistance, operator's manual and support CDTests both MM and SM fiber


•

•

•

•

•

•

•

•

•

•

•

••

••

•



E-12

OTDR OV1000 For testing and troubleshooting LAN, telco, CATV and FTTx networks. Combines a rugged platform with field-interchange-able multimode, single mode and advanced testing modules.

Utilizes Windows® CE technology6.4" color TFT touch screenFuture-ready with the ability to accept protocol testing modulesAvailable as a stand-alone product or as part of a kit


Fiber Inspection Microscope100X magnification for viewing multimode connectorsIncludes 2.5mm connector “Universal Adapter” for FC-, ST- and SC-style connectors

Oblique illumination provides excellent view of ferrule cleanliness and core conditionRugged, rubberized metal housing, precision glass optics and a built-in laser safety filterWhite LED illumination delivers 100,000 hours bulb lifeSoft padded carrying case includedOptional 200X Conversion Eyepiece threads on for viewing finish/polish of single mode connectors


Visual Fault FinderLaser light source used to locate breaks, faulty splices and crimpsUseful over a distance of 5km (3 miles)High output, class 2, 670nm laser diodeFitted with standard ST® adapterIncludes carrying case, lens cap, bat-teries, lanyard, and instruction sheetRugged, metal housingFrom Ideal Industries.Part No. VFF5

•••

•

•

•

•

•

•

••

•

••

••

•

Fiber Optic Inspection MicroscopesUsed to inspect optical fiber connectors on fiber optic cables, patch cords or test jumpers for scratches, dirt, pits, or other problems normally associated with poor transmission performance. By using threaded adapter mounts, Noyes fiber scopes can inspect the fiber and surrounding ferrule of virtually any connector style. From Noyes.

OFS 300The OFS 300-200C, with 200X magnification, is for inspection of multimode or single mode fibers. It offers 60 hours of continuous battery life, and a low battery indicator will flash when approxi-

mately eight hours of optimum brightness remains, reducing the risk of eyestrain.

VS 300 - View SafeRemoves concerns for eye safety while inspecting optical fiber connectors. The design eliminates the optical path to the eye by utilizing a miniature camera and a state-of-the-art micro-display that

achieves unparalleled clarity and resolution. No optical path to the user’s eyeNTSC video outputLightweight and has a molded easy grip case with easy access battery compartmentUses all the OFS 300-200C adapter caps and has an energy saving automatic shutoff

Part No. VS300

ID-L/DA Light SourceSingle button control to change the output mode from CW, 270Hz, 1kHz, and 2kHz. Operates more than 16 hours by battery (auto shutdown function)SC, FC, ST, DIN and DIA connectors are availableLightweight design for easy handling

Removable adapter for easy cleaningUsed in conjunction with the Fitel ID-L LightFinder™

optical identifierFrom Fitel.Part No. IDL

•••

•

•

•

•

•••



E-13

ID-H Fiber IdentifierSafely and effectively identifies the transmission direction, fiber path, and relative core power on live optical fibers. Used in conjunction with the Fitel ID-L Light Source.Detects the tone signal (270Hz, 1kHz, 2kHz) and traffic signal without requiring disconnection of the optical fiber

Super low insertion lossLED displays and audible tone indicators for clear identification

From Fitel.Part No. IDH

FiberViewer™

Fiber microscope ensures multi-mode and single mode terminations are clean and ready for optical transmission. Special safety filter helps protect eyes from infrared rays.

FT120 - 200X magnificationFT140 - 400X magnificationFrom Fluke Networks.

VisiFault™

A laser-powered visual fault locator which traces fibers, verifies continuity and polarity and helps find breaks in cables, connectors and splices. Continuous and flashing modes for easier identification. Compatible with 2.5mm and 1.25mm connectors. From Fluke Networks.

Fiber Inspection Probe FIP 400Featuring the best optical resolution in the industry, the FIP 400 checks fiber connec-tors and other terminations for polish quality and cleanliness down to 1μm. The probe can be used with a PC, with an EXFO test set or with its lightweight, handheld monitor. It is compat-ible with a wide range of single and multifiber con-nector types and is ideal for inspecting hard-to-reach connectors due to its slim design.

•

••

Optical Light Sources OLS-5, OLS-6Designed for dual-wavelength measurement in various single mode or multimode applications alongside PocketClass™ or SMART™ optical power meters.OLS-5 - Ideal for multimode operations, features 850 and 1300nm LEDs on one output port.

OLS-6 - Designed for various single mode applica-tions, features two laser diodes (1310/1550nm or 1550/1625nm) on two output ports. These separate optical ports for each wavelength test various applica-tions such as dense wavelength division multiplexing (DWDM) and FTTx installations. From JDSU.

Visual Fault Finder 170XLQuickly identifies bending losses and breaks in optical fibers.Continuous wave output mode for steady fault locationFind breaks to 3km

Blinking output mode increases viewing contrastEasy-to-use quick interface fits all 2.5mm connector interfaces (FC, SC, ST)1.0mW output powerErgonomic rotary switch permits easy one-handed operationRugged, compact and splash proof aluminum designTwo AA batteries provide 48 hours continuous operationNylon belt holster included

From Greenlee.Part No. 170XL

•

•••

••

••

•



E-14

Optical Light Meters OLP-5, OLP-6, OLP-8

Offers quick, easy and convenient field measurement of optical power and attenuation in fiber networks. For use on their own for simple output tests or with a light source for insertion loss measurements. OLP-5 - For LAN/multimode or single mode applications. Dynamic range of -60 to +5 dBm.OLP-6 - Covers most standard telecom

applications. Dynamic range of -65 to +10 dBm.OLP-8 - For higher power applications in the range of -50 to +23 dBm. such as Cat 5 (CATV) networks, dense wavelength division multiplexing (DWDM) systems and erbium doped fiber amplifier (EDFA) testing. From JDSU.

Optical Loss Test Kits SimpliFiber®

SimpliFiber kits include all the tools to verify proper installation and maintain multimode and single mode fiber cabling systems.Verify system loss and power levels at 800, 1310nm and 1550nmInspect connector endfaces at 200XLocate cable faults, polarity and connector problems

Carrying case provides equipment protection and transportation

Six kits available for a variety of applications. From Fluke Networks.

Fiber Certifier CertiFiber® Tests and certifies the compliance of multimode fiber optic networks to industry standards.Measures multimode fiber length and optical lossMeasures optical power and loss at 850 and 1300nm using LED dual-wavelength sourcesSaves 1,000 AutoTest results under

customized job and circuit ID nameFeatures a standards library for easy setupIncorporates interchangeable connector adapters for simple network connection

From Fluke Networks.

•

••

•

•

•

•

••

Video Microscope FiberInspector™ Pro A portable, dual magnification video microscope for all types of installed fiber terminations in hardware devices and patch panels.Easily inspects fiber connectors already installed on patch panelsQuickly determines what condition fiber connectors on a hardware device are in without disassembling the deviceContains high-magnification optics that

provide crisp, clear images of microscopic debris and end-face damage. From Fluke Networks.

Model No. FT600

Multifunction Loss Tester FOT-930 MaxTester

The new FOT-930 MaxTester is designed to help network service providers address CAPEX and OPEX issues, enable installers to easily adapt to all network types and provide CATV operators with a single-unit solution to their back-reflection, fiber-length, high-power

and bidirectional loss measurement needs. Combined with its video fiber inspection probe, this unit also enables the easy detection of dirty or damaged connec-tors, providing a clear view of connectors and fiber ends on the FOT-930’s high-resolution display.From EXFO.

PON Power MeterThe industry's first PON-specific power meter, the PPM-350B is the flagship of EXFO's line of test instruments spe-cifically intended for FTTh and FTTp systems. Available in four models: PPM-351B, PPM-352B, PPM-352B-EG and PPM-352B-EG-ER. Pass-through connection for ONT

signal measurement and simultaneous measurement of all PON signalsFiltered detectors for individual measurement of each wavelengthUpstream burst detection at 1310nmQuick, on-site test and measurement of PON signals, anywhere on the networkFault identification and isolation

From EXFO.

•

•

•

•

•

••

•



E-15

Optical Power Meter 560XLUsed to measure optical power or in conjunction with a LED or laser source to perform insertion loss testing on multi-mode and single mode fiber optic cabling. Easy to use - three buttons control allfunctionsLoss measurements in dB, power mea-

surements in dBm.01dB measurement resolutionMulti-wavelength storage - store and recall reference power levels for faster, more efficient measurementsSnap-On connector interface adapts to FC, SC and ST connectorsLong battery lifeUser selectable auto shut-off

From Tempo.

Optical Light Source 570XLDesigned for performing insertion loss testing in multimode fiber optic cabling. Dual wavelength output (850 and 1300nm) enables fast and accurate insertion loss measurements. Once the user has set the reference with an optical power meter, the 570XL provides a stable

output for hours of continuous work. Three models available for FC, SC and ST fiber optic connectors. From Tempo.

Optical Power Meter OPM1A portable optical power meter, the OPM1 measures optical power in premises, telco or broadband fiber optic networks. When used with an LED or laser light source, the unit also measures the attenuation (inser-tion loss) of multimode or single mode cables. 850, 1300, 1310 and 1550nm.Premises (Ge) and broadband (InGaAs) models

Displays optical power (dBm)Simple to use - only on/off and wavelength controlsN.I.S.T traceable

From Noyes.

•

•

••

•

••

•

•••

Fiber Loss Test Kitsfrom AFL Telecommunications

SMLP 4-4 OPM/OLS KitSingle mode and Multimode

Combines an OPM 4-2C optical power meter and an OLS-4 optical light source and is ideally suited for testing fiber optic networks with hybrid (single mode and multimode) cables. Measures loss

results at 850 and 1300nm for multimode fibers and 1310 and 1550nm for single mode fibers. The OLS-4 is an integrated, two-port LED and Laser light source. SC, ST and FC connector types available.

SMLP 5-5 OPM/OLS KitSingle mode and Multimode with Data Storage

Combines an OPM5-2C optical power meter and an OLS-4 optical light source and is ideally suited for testing fiber optic networks with hybrid (single mode and multimode) cables.Measures and stores loss results

at 850 and 1300nm for multimode fibers and 1310 and 1550nm for single mode fibers. The OLS-4 is an integrated, two-port LED and Laser light source. With supplied PC software, saved test results can be transferred to a PC for storage, printing and analysis. SC, ST and FC connector types available.

MLP 1 Series - Basic MultimodeFor testing multimode and single mode systems. By joining the OPM-1 optical power meter and the OLS-1 optical light source, the MLP 1 is a great kit for beginners or network owners. ST connector type only available.

Part No. MLP11S - Measures 850nmPart No. MLP12 - Measures 850 and 1300nm



E-16

MLP 4-2 - Multimode with Set Reference FeatureOffers accurate fiber optic testing. Combining the OPM-4-2C optical power meter and the OLS-1-2C optical light source in a rugged carry case, the MLP 4-2 is a complete test kit for fiber optic LANs and WANs.

Used during installations or maintenance, the MLP 4-2 performs insertion loss measurements on multimode fiber at 850 and 1300nm, as well as single mode fiber at 1300nm. The auto zero feature stores reference values at each wavelength for direct loss readings in dB. SC, ST and FC connector types available.

MLP 5-2B Multimode with Data StorageCombines OPM 5-2C optical power meter and the OLS-1-Dual light source in a rugged carrying case. Used during installations, the MLP 5-2B performs insertion loss measurements on multimode fiber at 850 and 1300nm, as well as

measurements on single mode fiber at 1300nm.The OPM-5-2C stores 500 loss readings for each wavelength for future down-loading to a computer or printer. Re-measures any specific memory location without erasing or modifying other loss readings. SC, ST and FC connector types available.

SLP 4-6D - SingIe mode with Set Reference Feature

Combines an OPM-4-4C optical power meter and the OLS 2-Dual light source. Used during instal-lations, the SLP 4-60 performs insertion loss measurements on single mode fiber at 1310 and 1550nm. SC, ST and FC connector types available.

Test Kit for Mobile Test, Conversion and Patch

Build your own cords for your test requirements. Durable nylon carrying case contains both transmit and receive cords and all the plug ends needed. Durable and mobile Does the job of six cords Tests on any DSX-3 panel Easy handling and storage

From Westek.Part No. KT290041

••••

Field Portable Test SetsTempo's line of basic test sets for fiber optic applica-tions feature all the equipment required for testing, troubleshooting, certification and maintenance. The rugged, splash-proof instruments are conveniently packaged in a water- and air-tight hard case.

MT-RJ Test SetsDesigned for multimode optical links, the MT-RJ test sets are an efficient solution for conducting insertion loss and link loss measure-ments on fiber optic network and premises applications incorporating the MT-RJ small form factor (SFF) duplex connector. Two single

wavelength sets are available with 850 or 1300nm LED sources and optical power meter.

Single Mode Test SetsDesigned to test, troubleshoot and maintain Telco, CATV, LAN and single mode network applications, these test sets can be used to measure output power and certify end-to-end attenua-tion on deployed fiber spans. The standard DIN-PC set includes an

optical power meter, dual wavelength 1310/1550nm LED source. Sets for FC-PC, ST-PC and SC-PC also are available.

Multimode Test SetsDesigned to test, troubleshoot and maintain LAN and other network applications, the multimode DIN-PC set includes an optical power meter and dual wavelength 850/1300nm LED source. Sets for E2000-PC, FC-PC, ST-PC and SC-PC also are available.



E-17

Dynatel™ LocatorsDynatel™ cable/pipe and fault loca-tors help find the exact path and estimated depth of power conduc-tors, fiber optic and telephone cables, metallic and non-metallic pipes with tracer wire, and they provide toning of aerial cable.

The hand-held cable/pipe and fault locators also identify and measure

points of cable damage where there is metallic contact to earth via a conductor or cable shield. They utilize proven fault detection methods with enhanced speed, sensitivity and noise rejection. The multi-antenna design provides high accuracy and performance while the user interface makes it simple and intuitive to use. From 3M. Call for details.

2210 Cable LocatorUsed to find the exact path and estimated depth of buried cables. Features two operator-selectable frequencies as well as visual cable locates.

2250 Cable LocatorUsed to find the exact path and estimated depth of buried cables or pipes with metallic tracer wires. Features four operator-selectable frequencies, visual cable locates and a direct readout of active duct probe.

2250M-iD Cable LocatorBest-in-class speed, sensitivity and accuracy. Includes 2250M Receiver with EMS-iD locating capabilities, 5 Watt Transmitter, 3" inductive coupler and direct connect cable for Telco/CATV applications.

2273 Cable/Sheath Fault LocatorUsed to find the exact path and estimated depth of CATV and telephone cables or pipes with metallic tracer wires. Features four operator-selectable frequen-cies, visual cable locates and a direct readout of active duct probe. Accessories also available.

2273M-iD Cable/Sheath Fault LocatorBest-in-class speed, sensitivity and accuracy. Includes a 2273M Receiver with EMS-iD locating capabilities, 5 Watt Transmitter, 3" inductive coupler, direct connect cable for Telco/CATV applications and fault locating accessories.

Electronic Marker System (EMS)The Electronic Marker System features durable, passive mark-ers that can be buried over key facilities during construction or used to mark existing facilities

during maintenance. After installation, EMS allows the user to find power, gas, water, wastewater, CATV and telephone utilities in the heaviest of traffic.

Each marker contains passive antennas within a water-resistant, PE shellOperate even in the presence of metal conduit or pipe, metallic conductors, fences, AC power lines and electronic markers of other utilitiesColor-coded to APWA standards for visual reference and each utility has its own specific frequency

Four EMS types are available: Near-Surface Markers, Ball Markers, Mini-Markers and Full-Range Markers. From 3M. Call for details.

EMS Locating AccessoryThe Dynatel™ 2205/2206 accessory provides the cable locator with the additional ability to pinpoint the exact location of buried EMS markers. It also allows the operator to simultaneously

trace a cable path while finding buried markers along the way. From 3M. Call for details.

Dynatel™ Rechargeable Battery for 5-Watt TransmittersA 5.4 Amp Hour sealed gel-cell battery used as an auxiliary battery in the Dynatel Transmitters 2200 Series. Plugs into external power plug and provides battery powering for the transmitter. Can be used for the same application that the current alkaline ‘C’ cells are used for in 0.5 Watt and 3.0 Watt output levels. Allows access to the 5.0 Watt output level of the transmitter that requires the external input.Comes complete with a battery, 2-stage charger, hook and loop fasteners that are pre-mounted to the battery and an installation instruction sheet. From 3M.Part No. 2200RB

•

•

•



Notes

E-18

Test Equipment


800-238-7514 Info...It replaces Dynatel Subscriber Loop Analyzer 965DSP. The 965AMS has a bigger,...

Documents

Transcript of 800-238-7514 Info...It replaces Dynatel Subscriber Loop Analyzer 965DSP. The 965AMS has a bigger,...