7.OWG001206 Signaling Data Configuration ISSUE1.0

7/22/2019 7.OWG001206 Signaling Data Configuration ISSUE1.0

1/41

Wireless Curriculum Development Section

ISSUE

OWG001206 MSOFTX3000

Signaling Data Configuration

1.0


2/41

2Confidential Information of Huawei.

No Spreading without Permission. Security Level: Internal

Course Objectives

Upon completion of this course, the trainees should be

able to:

Understand signaling table relation

Master the signaling link and GT configuration


3/41



References

MSOFTX3000 Operation Manual-Data Configuration


4/41



Course Contents

Chapter 1 Basic concepts

Chapter 2 MTP Data Configuration

Chapter 3 SCCP Data Configuration

Chapter 4 Examples


5/41



Hierarchy of SS7 protocol

MAP CAP

TCAP

BSSAP+

SCCP

MTP

TCAP: Transaction Capabilities Application PartSCCP: signaling connection control part

MTP: message transfer part


6/41



Basic Concepts of No.7 Signaling System

Signaling Link

Signaling Link set

SLC

Signaling Route

SLS


7/41





8/41

8Confidential Information of Huawei.No Spreading without Permission. Security Level: Internal

Signaling link:

one of the elements of the signaling

network, which are the physical links

connecting all the signaling points and

signaling transfer points, and over whichthe signaling messages are transmitted.



9/41


A number of parallel signalling

links that directly interconnect two

signalling points constitute a

Signalling LinkSet.

Signaling linkset:



10/41


SLC: Signaling link code

Each link in one linkset must be

numbered uniformly.

We call this number SLC.

SLC must be same between twooffices.



11/41


SLS: Signaling link Selection

SLS is used to signaling link/routeselection.

In MSOFTX3000/SSP/IP, SLS

cooperates with MASK in data

configuration, and implement theload sharing between signaling

linkset/link.



12/41


The path leading from the local

signaling point to the destination

signaling point is called signaling

route.

Signaling Route:



13/41


Course Contents




Chapter 4 Examples


14/41


Relationship of MTP Configuration table


15/41

15

Confidential Information of Huawei.


ConfigurationProcedure

MTP Data Configuration

Configure signalinglink set

End

Configure DSP

Configure signalinglink

Configure signalingroute


16/41

16



Configurationfor new signaling links in existed linkset


Modify signalinglink set configuration

End

Configure signaling

link


17/41

17



Configurationfor new DSP using existed linksets


End

Configure DSP

Configure signalingroute


18/41

18



Course Contents




Chapter 4 Examples


19/41

19



Procedure for SCCP data configuration

SCCP DSP table (ADD SCCPDPC) SCCP SSN table (ADD SCCPSSN)

GT table (ADD SCCPGT)


20/41

20



SCCP DSP table

Like the MTP destination signaling

point table, only the destination

signaling point data which can be seen

at the SCCP layer and can transmit the

SCCP messages should be set.


21/41

21



SCCP addressing mode

SubSystem

SCCP

MTP

SubSystem

SCCP

MTP

SubSystem

SCCP

MTP

DPC+GT DPC

SPA STP SPB


22/41

22



SCCP SSN table

SCCP SSN table (ADD SCCPSSN) Local office

MSC,VLR, BSSAP, CAP, and SCMG,RANAP

Other Office

HLR:HLR,SCMG

Other MSOFTX3000:MSC,SCMG,VLR,MAP

BSC:BSSAP/INAP, SCMG

STP: SCMG

RNC:RANAP,SCMG


23/41

23



In this table,you should configure:

Local office

MSC/VLR No.

For location update

E.214 code for MS E.164 code for HLR No.

For the called MS

E.164 code for MS

For Short Messages

E.164 code for SMC No.

For SCP

E.164 code for SCP No. which has

relationship with the local office

GT table


24/41

24



Course Contents




Chapter 4 Examples


25/41

25



Chapter 4 Examples

2.1 HLR

2.2 SMC

2.3 SGSN

2.4 GMLC


26/41

26



Procedures for configuring data at MSOFTX3000

for interworking with HLR

Procedure Command

1. Configure MTP

1) Add MTP DSP

2) Add MTP link set

3) Add MTP route

4) Add MTP link

ADD N7DSP

ADD N7LKS

ADD N7RT

ADD N7LNK

2. Configure SCCP

1) Add SCCP remote signaling point

2) Add SCCP subsystem

3) Add SCCP GT

ADD SCCPDSP

ADD SCCPSSN

ADD SCCPGT


27/41

27



GT table

When MSOFTX3000 is directly connected to HLR in signaling, it isrequired to configure the following GT data for the three cases.

1)IMSI GT and HLR-NUMBER GT for location update

2)Ordinary GT (HLR-MSISDN GT) when the subscriber is called

3)Local MSC GT to be queried when the local office performs

second-stagenumber analysis.


28/41

28



Chapter 4 Examples

2.1 HLR

2.2 SMC

2.3 SGSN

2.4 GMLC


29/41

29



Networking and protocols between MSOFTX3000

and SMC

MSOFTX3000

TDM

TCAP

SCCP

MTP3

MTP2

MTP1

SMCE

MAP

TDM based

TCAP

SCCP

MTP3

MTP2

MTP1

E

MAP


30/41

30



Procedures for configuring data at MSOFTX3000

for interworking with SMC

Procedure Command

1. Configure MTP

1) Add MTP3 DSP

2) Add MTP3 link set

3) Add MTP3 route

4) Add MTP link

ADD N7DSP

ADD N7LKS

ADD N7RT

ADD N7LNK

2. Configure SCCP1) Add SCCP remote signaling point

2) Add SCCP subsystem (SCMG,MSC

subsystem)

3) Add SCCP GT

ADD SCCPDPC

ADD SCCPSSN

ADD SCCPGT

3. Modify MAP configuration parameter

tableMOD MAPACCFG


31/41

31



Parameter relationship between MSOFTX3000 and

SCP

ADD N7DSP

[DSP index]

[O PC]

ADD N7LKS

[LinkSet Index]

ADD N7RT

[Priority]

ADD N7LNK

[Link No]

[Start Circuit No ]

[LinkSet Index]

[Signaling Link Code ]

SMC

Peer end MSC DPC

Signaling network indicator

SMC OPC

[Adjacent DSP Index]

[LinkSet Index]

[DSP index]ADD SCCPDSP

[DPC]

ADD SCCPSSN

[SSN]

[OPC]

ADD SCCPGT

SLC

ADD N7DSP

[DPC]

ADD N7LKS

ADD N7RT

ADD N7LNK

[Link No.]

[Start Circuit No. ]

[ ]

[Signaling Link Code ]

MSOFTX3000 parametersparameters

[DSP index]

ADD SCCPSSN

[NI]

[SPC]

ADD SCCPGT

[GT Address Information]

[NI ]

[SPC]

[OPC]

[NI ]

[NI]

SMC NUMBER


32/41

32



Chapter 4 Examples

2.1 HLR

2.2 SMC

2.3 SGSN

2.4 GMLC


33/41

33




and SGSN

TDM

BSSAP+

SCCP

MTP3

MTP2

MTP1

SGSNGs

TDM

BSSAP+

SCCP

MTP3

MTP2

MTP1

SGSNGs

MSOFTX3000

TDM

BSSAP+

SCCP

MTP3

MTP2

MTP1

SGSNGs

TDM based

BSSAP+

SCCP

MTP3

MTP2

MTP1

SGSNGs


34/41

34



Data configuration procedures

Procedure Command

Configure MTP

1) Add MTP DSP

2) Add MTP link set

3) Add MTP route

4) Add MTP link

ADD N7DSP

ADD N7LKS

ADD N7RT

ADD N7LNK

Configure SCCP

1) Add SCCP remote signaling point

2) Add SCCP subsystem (Gs, SCMG)

3) Configure SCCP GT

ADD SCCPDPC

ADD SCCPSSN

ADD SCCPGT

Configure SGSN

1) Configure SGSN number

2) Configure Gs interface network

indicator

3) Modify MAP configuration

parameter table

ADD SGSNNOMOD MSFP

MOD MAPACCFG


35/41

35




SGSN

ADD N7DSP

[DSP index]

[OPC]

ADD N7LKS

[LinkSet Index]

ADD N7RT

[Priority]

ADD N7LNK[Link No]

[Start Circuit No

[[LinkSet Index]

[Signaling Link Code

SGSN parameters

Peer MSC DPC

Signaling network indicator

SGSN OPC

[Adjacent Point Index]

[LinkSet Index]


[DPC]

ADD SCCPSSN

[SSN ]

[SPC

[OPC]

ADD SCCPGT


SLC

ADD N7DSP

[DPC]

ADD N7LKS

ADD N7RT

[Priority]

ADD N7LNK[Link No.

[Start Circuit No.]

[

[Signaling Link Code]

MSOFTX3000 parameters


[DSP index]

[SSN]

[NI]

[SPC]

ADD SCCPGT

[NI]

[SPC]

[OPC]

[NI]

[NI]

ADD SGSNNO

[SGSN NUMBER]SGSN number


36/41

36



Chapter 4 Examples

2.1 HLR

2.2 SMC

2.3 SGSN

2.4 GMLC

i SO 3000


37/41

37




and GMLC

MSOFTX3000

TDM

TCAP

SCCP

MTP3

MTP2

MTP1

GMLCMAP

MAP

TDM based

MAP

C fi i d f i ki b


38/41

38



Configuration procedure of interworking between

MSOFTX3000 and GMLC

Procedure CommandConfigure MTP

1) Add MTP3 destination signaling point

2) Add MTP3 link set

3) Add MTP3 route

4) Add MTP3 link

ADD N7DSP

ADD N7LKS

ADD N7RT

ADD N7LNK

Configure SCCP1) Add SCCP remote signaling point

2) Add SCCP subsystem (GMLC, SCMG)

3) Add SCCP GT to GMLC

ADD SCCPDSP

ADD SCCPSSN

ADD SCCPGT

Configure LCS data

1) Configure GMLC number

2) Configure client GMLC information3) Configure emergency call GMLC number

4) Configure emergency service category

information

5) Add called analysis data (optional)

ADD GMLC

ADD GMLCCLTADD GMLCECL

ADD ESRVCAT

ADD CNACLD

P t l ti hi b t MSOFTX3000 d


39/41

39




GMLC

ADD N7DSP

[DSP index]

[OPC]

ADD N7LKS

[LinkSet Index]

ADD N7RT

[Priority]

ADD N7LNK

[Link No]

[Start Circuit No.]

[LinkSet Index]

[Signaling Link Code]

GMLC parameters

MSC DPC

Network Indicator

GMLC OPC


[LinkSet Index]


[DPC]

ADD SCCPSSN

[SSN]

[SPC]

[OPC]

ADD SCCPGT


[NI]

[DPC]

ADD N7LKS

ADD N7LNK

[Link No.]

MSOFTX3000 parameters

[DSP index]

ADD SCCPSSN

[SSN]

[NI]

[SPC]

ADD SCCPGT

[NI]

[SPC]

Singaling Link Code (SLC)

[OPC]

[NI]

[NI]

ADD GMLC

[GMLC NUMBER]GMLC No.

ADD GMLCCLT

[GMLC NUMBER]

[GMLC CLIENT ID]

ADD GMLCECL

[GMLC NUMBER]

[GCI OR LAI]

ADD ESRVCAT

[Service Dial Number]

[Emergency Services]

[Emergency Call Number]


40/41

40



Summary

Master data configuration steps

MTP

SCCP

Master data configuration method of the followingproducts

HLR

SMC

SGSN

GMLC


41/41

41

7.OWG001206 Signaling Data Configuration ISSUE1.0

Documents

Transcript of 7.OWG001206 Signaling Data Configuration ISSUE1.0