769-00861 snowthrower

1
To the Customer: For shipping purposes, the control cables have not been attached to the snow thrower. Please follow instructions below to attach these cables using hardware listed here. Hardware Provided (See Figure 1) NOTE: These items replace the items listed in Group E of the Hardware Pack on page 5 of the owner’s manual (Form no. 770-10001F). Figure 1 Attaching Control Cables NOTE: These instructions replace those on pages 8 & 9 of the owner’s manual (Form no. 770-10001F) under the heading Attaching Control Cables. Take a Z fitting from the hardware pack and insert the Z end into the hole on the left clutch grip on the handle panel. See Figure 2. Figure 2 If the hex nut was not threaded on to the Z fitting before shipping, do so now. Refer to Figure 1. Route the left cable between engine and speed selector plate and then between handle panel and clutch lever pivot rod. Make sure the cable is routed correctly in the cable roller guides located at the lower rear of the unit. Thread cable onto the left Z fitting. Assemble the right Z fitting on the right clutch grip and attach the right cable in the same manner. Both cables should have minimal slack, but not tight. Tighten or loosen hex nuts on Z fittings to adjust. Once properly adjusted, tighten the jam nut against the coupling end of the cable to lock it in position. IMPORTANT: If the right lock-out cable is not adjusted, the wheels will tend to turn. If the left lock-out cable is not adjusted, the augers will keep on rotating. The drive clutch cable is routed over the axle. NOTE: Follow Auger Control Test on page 13 of the owner’s manual prior to operating your snow thrower. Hex Nuts* 712-0121 (2) Hex Nut (2) Z Fitting (2) NOTE: Two extra nuts are included in the hardware pack in the event either is lost during shipping. WARNING: Do not over-tighten the clutch cables. Tension on either cable in the disengaged (up) position may override the safety features of the machine. “Z” Fitting Hex Nut Clutch Grip Handle Panel DATE: August 1, 2003 SUBJECT: Assembly Instructions MODELS: Snow Thrower Model 611 Supplement Sheet FORM NO. 769-00861

description

snow thrower

Transcript of 769-00861 snowthrower

Page 1: 769-00861 snowthrower

To the Customer:

For shipping purposes, the control cables have not been attached to the snow thrower. Please follow instructions below to attach these cables using hardware listed here.

Hardware Provided (See Figure 1)

NOTE: These items replace the items listed in Group Eof the Hardware Pack on page 5 of the owner’s manual(Form no. 770-10001F).

Figure 1

Attaching Control CablesNOTE: These instructions replace those on pages 8 &9 of the owner’s manual (Form no. 770-10001F) underthe heading Attaching Control Cables.

• Take a Z fitting from the hardware pack and insert the Z end into the hole on the left clutch grip on the handle panel. See Figure 2.

Figure 2

• If the hex nut was not threaded on to the Z fitting before shipping, do so now. Refer to Figure 1.

• Route the left cable between engine and speed selector plate and then between handle panel and clutch lever pivot rod. Make sure the cable is routed correctly in the cable roller guides located at the lower rear of the unit.

• Thread cable onto the left Z fitting.• Assemble the right Z fitting on the right clutch grip

and attach the right cable in the same manner. Both cables should have minimal slack, but not tight.

• Tighten or loosen hex nuts on Z fittings to adjust.• Once properly adjusted, tighten the jam nut against

the coupling end of the cable to lock it in position.

IMPORTANT: If the right lock-out cable is not adjusted, the wheels will tend to turn. If the left lock-out cable is not adjusted, the augers will keep on rotating. The drive clutch cable is routed over the axle.

NOTE: Follow Auger Control Test on page 13 of theowner’s manual prior to operating your snow thrower.

Hex Nuts*712-0121 (2)

Hex Nut (2)

Z Fitting (2)

NOTE: Two extra nutsare included in thehardware pack in theevent either is lost duringshipping.

WARNING: Do not over-tighten the clutch cables. Tension on either cable in the disengaged (up) position may override the safety features of the machine.

“Z” Fitting

Hex Nut

Clutch Grip

Handle Panel

DATE: August 1, 2003

SUBJECT: Assembly Instructions

MODELS: Snow Thrower Model 611Supplement Sheet

FORM NO. 769-00861