7369v1.0 G52-73691X5
description
Transcript of 7369v1.0 G52-73691X5
-
iK9N Neo V2/ V3 SeriesMS-7369 (V1.X) Mainboard
G52-73691X5
-
ii
Copyright Notice
The material in this document is the intellectual property of MICRO-STARINTERNATIONAL. We take every care in the preparation of this document, but noguarantee is given as to the correctness of its contents. Our products are undercontinual improvement and we reserve the right to make changes without notice.
Trademarks
All trademarks are the properties of their respective owners.
NVIDIA, the NVIDIA logo, DualNet, and nForce are registered trademarks or trade-marks of NVIDIA Corporation in the United States and/or other countries.AMD, Athlon, Athlon XP, Thoroughbred, and Duron are registered trade-marks of AMD Corporation.Intel , Pentium, CoreTM are registered trademarks of Intel Corporation.PS/2 and OS/2 are registered trademarks of International Business MachinesCorporation.W indows 95/98/2000/NT/XP/Vista are registered trademarks of Microsof tCorporation.Netware is a registered trademark of Novell, Inc.Award is a registered trademark of Phoenix Technologies Ltd.AMI is a registered trademark of American Megatrends Inc.
Revision History
Revision Revision History DateV1.0 First release for Europe August 2007
Technical Support
If a problem arises with your system and no solution can be obtained from the usersmanual, please contact your place of purchase or local distributor. Alternatively,please try the following help resources for further guidance.
Visit the MSI website for FAQ, technical guide, BIOS updates, driver updates,and other in f ormat ion: ht tp: / /g lobal .msi.com.tw/ index.php?func=faqIndexContact our technical staff at: http://support.msi.com.tw/
-
iii
Safety Instructions
CAUTION: Danger of explos ion if bat tery is incorrectly replaced.Replace only with the same or equivalent type recommended by themanufacturer.
1. Always read the safety instructions carefully.2. Keep this Users Manual for future reference.3. Keep this equipment away from humidity.4. Lay this equipment on a reliable f lat surface before setting it up.5. The openings on the enclosure are for air convection hence protects the equip-
ment from overheating. DO NOT COVER THE OPENINGS.6. Make sure the voltage of the power source and adjust properly 110/220V be-
fore connecting the equipment to the power inlet.7. Place the power cord such a way that people can not step on it. Do not place
anything over the power cord.8. Always Unplug the Power Cord before inserting any add-on card or module.9. All cautions and warnings on the equipment should be noted.10. Never pour any liquid into the opening that could damage or cause electrical
shock.11. If any of the following situations arises, get the equipment checked by a service
personnel: The power cord or plug is damaged. Liquid has penetrated into the equipment. The equipment has been exposed to moisture. The equipment has not work well or you can not get it work according to
Users Manual. The equipment has dropped and damaged. The equipment has obvious sign of breakage.
12. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT UNCONDITIONED, STOR-AGE TEMPERATURE ABOVE 600 C (1400F), IT MAY DAMAGE THE EQUIPMENT.
-
iv
FCC-B Radio Frequency Interference Statement
This equipment has beentested and found to complywith the limits for a Class Bdigital device, pursuant to Part15 of the FCC Rules. These limits are designed to provide reasonable protectionagainst harmful interference in a residential installation. This equipment generates,uses and can radiate radio frequency energy and, if not installed and used in accor-dance with the instructions, may cause harmful interference to radio communications.However, there is no guarantee that interference will not occur in a particularinstallation. If this equipment does cause harmful interference to radio or televisionreception, which can be determined by turning the equipment off and on, the user isencouraged to try to correct the interference by one or more of the measures listedbelow.
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that towhich the receiver is connected.
Consult the dealer or an experienced radio/television technician for help.
Notice 1The changes or modif ications not expressly approved by the party responsible forcompliance could void the users authority to operate the equipment.
Notice 2Shielded interface cables and A.C. power cord, if any, must be used in order tocomply with the emission limits.
VOIR LA NOTICE DINSTALLATION AVANT DE RACCORDER AU RESEAU.
Micro-Star InternationalMS-7369
This device complies with Part 15 of the FCC Rules. Operation is subject to thefollowing two conditions:(1) this device may not cause harmful interference, and(2) this device must accept any interference received, including interference that
may cause undesired operation.
-
vWEEE (Waste Electrical and Electronic Equipment) Statement
-
vi
-
vii
-
viii
CONTENTSCopyright Notice ......................................................................................................... iiTrademarks .................................................................................................................. iiRevision History ......................................................................................................... iiTechnical Support ...................................................................................................... iiSafety Instructions ................................................................................................... iiiFCC-B Radio Frequency Interference Statement ............................................. ivWEEE (Waste Electrical and Electronic Equipment) Statement ....................... vEnglish ...................................................................................................................... En-1
Specifications .................................................................................................... En-2Central Processing Unit: CPU ........................................................................... En-5Memory............................................................................................................... En-7Connectors, Jumpers, Slots ............................................................................. En-9Back Panel ........................................................................................................ En-18BIOS Setup ....................................................................................................... En-21Software Information ...................................................................................... En-25
Deutsch ....................................................................................................................De-1Spezif ikationen .................................................................................................. De-2Hauptprozessor: CPU ....................................................................................... De-5Speicher ............................................................................................................. De-7Anschlsse, Steckbrcken und Slots ............................................................. De-9Hinteres Anschlusspaneel ............................................................................. De-18BIOS Setup ....................................................................................................... De-21Software-Information ...................................................................................... De-25
Franais .....................................................................................................................Fr-1Spcificits ......................................................................................................... Fr-2Central Processing Unit: CPU ............................................................................ Fr-5Mmoire ............................................................................................................... Fr-7Connecteurs, Cavaliers, Slots .......................................................................... Fr-9Panneau Arrire ............................................................................................... Fr-18Configuration du BIOS ...................................................................................... Fr-21Information de Logiciel ..................................................................................... Fr-25
....................................................................................................................Ru-1 ............................................................................................... Ru-2 (CPU) ..................................................................... Ru-5 ............................................................................................................... Ru-7, , ............................................................ Ru-9 ............................................................................................... Ru-18 BIOS .............................................................................................. Ru-21 ................................................... Ru-25
-
En-1
Engl
ish
K9N Neo V2/ V3Users Guide
English
-
En-2
MS-7369 Mainboard
Specifications
Processor Support- AMD Athlon 64/ 64X2 & Sempron in the socket AM2 package(For the latest information about CPU, please visit http://global.msi.com.tw/index.php?func=cpuform)
Supported FSB- HyperTransport supporting speed up to 1 GHz (2000MT/s)
Chipset- nVidia nForce 520/ nForce 560 chipset
Memory Support- DDR2 533/667/800 SDRAM (240pin/ non-ECC)- 4 DDR2 DIMMs (8GB Max)(For more information on compatible components, please visit http://global.msi.com.tw/index.php?func=testreport)
LAN- Supports Giga LAN 10/100/1000 Fast Ethernet by Realtek RTL8111B/ RTL8211BL (optional)
Audio- Controlled by Realtek ALC888- Supports 7.1 channels audio out- Compliant with Azalia Spec
IDE- 1 IDE port- Supports Ultra DMA 66/100/133, PIO & Bus Master operation mode
SATA- 4 SATA ports support 4 SATA devices- Supports storage and data transfers at up to 300 MB/s
RAID- SATA1~4 support RAID 0/ 1/ 0+1/ 5 or JBOD mode (RAID 5mode only for nForce 560)
-
En-3
Engl
ishFloppy
- 1 floppy port- Supports 1 FDD with 360KB, 720KB, 1.2MB, 1.44MB and 2.88MB
Connectors
Back panel- 1 PS/2 mouse port- 1 PS/2 keyboard port- 1 Serial port- 1 Parallel port support SPP/EPP/ECP mode- 4 USB 2.0 Ports- 1 LAN jack- 6 audio jacks
On-Board Pinheaders- 3 USB 2.0 pin headers- 1 Chassis Intrusion Switch pinheader- 1 SPDIF-Out pinheader- 1 Front Panel Audio pinheader- 1 CD-In pinheaderSlots- 1 PCI Express x 16 slot- 2 PCI Express x 1 slots- 3 PCI slots, support 3.3V/ 5V PCI bus Interface
Form Factor- ATX (30.5 cm X 20.0 cm)
Mounting- 6 mounting holes
-
En-4
MS-7369 Mainboard
Quick Components Guide of K9N Neo V2/ K9N Neo V3 Series(MS-7369 v1.X) Mainboard
1 En-5
AEn-18
BEn-18
CEn-18
G
En-19
HEn-20
J M
I
L
NK
En-20
En-20
En-20
3 En-7
4 En-9
4En-9
21 En-15
6 En-9
7 En-10
8 En-10
10 En-115 En-911
En-1114
En-12
En-1112
20 En-15
15 En-12
27 En-17
26 En-17
23En-16
4En-9
-
En-5
Engl
ish
The mainboard supports AMD processor. The mainboard uses a CPU socketcalled Socket AM2 for easy CPU installation. If you do not have the CPU cooler,consult your dealer before turning on the computer.For the latest information about CPU, please visit http://global.msi.com.tw/index.php?func=cpuform
1
Central Processing Unit: CPU
CPU Installation Procedures for Socket AM21. Please turn off the power and unplug the power cord be-
fore installing the CPU.2. Pull the lever sideways away from the socket. Make sure to
raise the lever up to a 90-degree angle.3. Look for the gold arrow of the CPU. The gold arrow should
point as shown in the picture. The CPU can only fit in thecorrect orientation.
4. If the CPU is correctly installed, the pins should be com-pletely embedded into the socket and can not be seen. Please note that anyviolation of the correct installation procedures may cause permanent damages toyour mainboard.
5. Press the CPU down firmly into the socket and close the lever. As the CPU is likely tomove while the lever is being closed, always close the lever with your fingers press-ing tightly on top of the CPU to make sure the CPU is properly and completelyembedded into the socket.
Gold arrow
Correct CPUplacement
Important
OverheatingOverheating will seriously damage the CPU and system. Always make sure thecooling fan can work properly to protect the CPU from overheating. Make surethat you apply an even layer of thermal paste (or thermal tape) between the CPUand the heatsink to enhance heat dissipation.Replaceing the CPUWhile replacing the CPU, always turn off the ATX power supply or unplug thepower supplys power cord from the grounded outlet first to ensure the safety ofCPU.OverclockingWe do not guarantee the damages or risks caused by inadequate operation orbeyond product specifications.
-
En-6
MS-7369 Mainboard
Installing CPU Cooler SetWhen you are installing the CPU, make sure the CPU has a heat sink and a coolingfan attached on the top to prevent overheating. If you do not have the CPU cooler,consult your dealer before turning on the computer.
1. Position the cooling set onto the retention mechanism. Hook one end of the clip tohook first.
2. Then press down the other end of the clip to fasten the cooling set on the top of theretention mechanism. Locate the Fix Lever and lift up it .
3. Fasten down the lever.4. Attach the CPU Fan cable to the CPU fan connector on the mainboard.
Fixed Lever
Important
Mainboard photos shown in this section are for demonstration of the CPU/ coolerinstallation only. The appearance of your mainboard may vary depending on themodel you purchase.
-
En-7
Engl
ish
Memory
DDRSpecification : 184-pin, 2.5v.Single channel definition : All DIMM slots are GREEN color.Dual channels definition : DIMM slot(s) on Channel A are marked in GREEN color.DIMM slot(s) on Channel B are marked in Purple color.
DDR2Specification : 240-pin, 1.8v.Single channel definition : All DIMM slots are GREEN color.Dual channels definition : DIMM slot(s) on Channel A are marked in GREEN color.DIMM slot(s) on Channel B are marked in Orange color.
40x2=80 pin 52x2=104 pin
2
3
Important
- DDR2 memory modules are not interchangeable with DDR and the DDR2 standard is not backwards compatible. You should always install DDR2 memorymodules in the DDR2 DIMM slots.
- In Dual-Channel mode, make sure that you install memory modules of the sametype and density in different channel DIMM slots.
- To enable successful system boot-up, always insert the memory modules into theDIMM1 first.
64x2=128 pin56x2=112 pin
-
En-8
MS-7369 Mainboard
Installing Memory ModulesYou can find the notch on the memory modules and the volt on the DIMM slots whetherDDR or DDR2. Follow the procedures below to install the memory module properly.
1. The memory modules has only one notch on the center and will only fit in the rightorientation.
2. Insert the memory module vertically into the DIMM slot. Then push it in until thegolden finger on the memory module is deeply inserted in the DIMM slot.
3. The plastic clip at each side of the DIMM slot will automatically close.
Important
You can barely see the golden finger if the memory module is properly inserted inthe DIMM slot.
Volt Notch
-
En-9
Engl
ish
Connectors, Jumpers, SlotsFan Power Connectors
The fan power connectors support system cooling fan with +12V. The CPU FAN supportsSmart FAN function. When connect the wire to the connectors, always take note that thered wire is the positive and should be connected to the +12V, the black wire is Groundand should be connected to GND. If the mainboard has a System Hardware Monitorchipset on-board, you must use a specially designed fan with speed sensor to takeadvantage of the fan control.
4
SYS FAN/ NB FAN/POWER FAN
CPU FAN
Floppy Disk Drive ConnectorThis connector supports 360KB, 720KB, 1.2MB, 1.44MB or 2.88MB floppy disk drive.
5
IDE connectorThis connector supports IDE hard disk drives, optical disk drives and other IDE devices.
6
Important
1. Please refer to the recommended CPU fans at processors official website orconsult the vendors for proper CPU cooling fan.
2. Fan cooler set with 3 or 4 pins power connector are both available for CPUFAN.3. CPUFAN supports fan control. You can setup it in BIOS Setup. Or CPUFAN
supports fan control. You can install Dual Core Center utility that willautomatically control the CPU fan speed according to the actual CPUtemperature.
Important
If you install two IDE devices on the same cable, you must configure the drivesseparately to master / slave mode by setting jumpers. Refer to IDE devicesdocumentation supplied by the vendors for jumper setting instructions.
SENSOR+12VGND
ControlSENSOR+12VGND
-
En-10
MS-7369 Mainboard
Front Panel ConnectorsThese connectors are for electrical connection to the front panel switches and LEDs.The JFP1 is compliant with Intel Front Panel I/O Connectivity Design Guide.
IEEE1394 Connector (Green)This connector allows you to connect the IEEE1394 device via an optional IEEE1394bracket.
8
9
Serial ATA ConnectorThis connector is a high-speed Serial ATA interface port. Each connector can connect toone Serial ATA device.
7
Important
Please do not fold the Serial ATA cable into 90-degree angle. Otherwise, dataloss may occur during transmission.
IEEE1394 Bracket(Optional)
1 2
9 10
TPA+
Gro
und
TPB
+C
able
pow
erK
ey (n
o pi
n)
TPA
-G
roun
dTP
B-
Cab
le po
wer
Gro
und
12
910
HDDLED
ResetSwitch
PowerLED
PowerSwitch
JFP1
Speaker
JFP2
78
PowerLED
12
-
En-11
Engl
ish
SPDIF Bracket (Optional)
Front USB Connector (Yellow)This connector, compliant with Intel I/O Connectivity Design Guide, is ideal for con-necting high-speed USB interface peripherals such as USB HDD, digital cameras, MP3players, printers, modems and the like.
Important
Note that the pins of VCC and GND must be connected correctly to avoid possibledamage.
10
Front Panel Audio Connector (Azalia Spec)This connector allows you to connect the front panel audio and is compliant with IntelFront Panel I/O Connectivity Design Guide.
11
12
USB 2.0 Bracket(Optional)U
SBO
C
10 1 2
VC
CU
SB0
-U
SB0+
GN
DK
ey (n
o pi
n)
VC
CU
SB1
-U
SB1+
GN
D
9
v S/PDIF-Out Connector (Optional, for HDMI graphics card only)This connector is used to connect S/PDIF (Sony & Philips Digital Interconnect Format)interface for digital audio transmission to the HDMI graphics card.
SPDIFO GND
12
910
MIC
_L
MIC
_R
LIN
E o
ut_R
Fron
t_JD
LIN
E o
ut_L
Gro
und
Pres
ence
#M
IC_J
DN
C(N
o pi
n)LI
NE
out
_JD
-
En-12
MS-7369 Mainboard
CD-In ConnectorThis connector is provided for external audio input.
Chassis Intrusion ConnectorThis connector connects to the chassis intrusion switch cable. If the chassis is opened,the chassis intrusion mechanism will be activated. The system will record this status andshow a warning message on the screen. To clear the warning, you must enter the BIOSutility and clear the record.
Front Panel Audio Connector (AC97 Spec)This connector allows you to connect the front panel audio and is compliant with IntelFront Panel I/O Connectivity Design Guide.
15
1 2
9 10
AUD_MICAUD_MIC_BIAS
AUD_FPout_RHP_ON
AUD_FPout_L
AUD_GNDAUD_VCCAUD_RET_RKeyAUD_RET_L
13
Important
If you dont want to connect to the front audio header, pins 5 & 6, 9 & 10 haveto be jumpered in order to have signal output directed to the rear audio ports.Otherwise, the Line-Out connector on the back panel will not function.
14
GNDRL
12
CINTRUGND
-
En-13
Engl
ish
Infrared Module ConnectorThis connector allows you to connect to infrared module and is compliant with IntelFront Panel I/O Connectivity Design Guide. You must configure the setting through theBIOS setup to use the infrared function.
Serial Port ConnectorThis connector is a 16550A high speed communication port that sends/receives 16bytes FIFOs. You can attach a serial device.
TV-Out ConnectorThis connector is for you to attach an optional TV-Out bracket that offers some types ofTV-Out connectors. Select the appropriate one to connect to an television.
65
21NC
VCC5IRTX
NCGroundIRRX
16
17
18
1
9
2DCDSINSOUTDTRGroundDSRRTSCTSRI
5
1 2Ground
YoutCout
COMP or CVBSGround
-
En-14
MS-7369 Mainboard
1
9
2
10
DBG1DBG2DBG3DBG4
Key
DBR1DBR2DBR3DBR4NC
BIOS Sign OnThis will start showing informationabout logo, processor brand name,etc...
Testing Base and Extended MemoryTesting base memory from 240K to640K and extended memory above1MB using various patterns.
Assign Resources to all ISA.
Initializing Hard Drive ControllerThis will initialize IDE drive andcontroller.
Initializing Floppy Drive ControllerThis will initialize Floppy Drive andcontroller.
Boot AttemptThis will set low stack and boot viaINT 19h.
Operating System Booting
System Power ONThe D-LED will hang here if theprocessor is damaged or not in-stalled properly.
Initializing Keyboard Controller.
Testing VGA BIOSThis will start writing VGA sign-onmessage to the screen.
Processor InitializationThis will show information regardingthe processor (like brand name, sys-tem bus, etc...)
Testing RTC (Real Time Clock)
Description
Red Green
LED Signal
1 2
3 4
1 2
3 4
1 2
3 4
1 2
3 4
1 2
3 4
1 2
3 4
1 2
3 4
1 2
3 4
DescriptionLED Signal
1 2
3 4
1 2
3 4
1 2
3 4
1 2
3 4
1 2
3 4
1 2
3 4
1 2
3 4
1 2
3 4
Early Chipset Initialization
Memory Detection TestTesting onboard memory size. TheD-LED will hang if the memory mod-ule is damaged or not installedproperly.
Decompressing BIOS image to RAMfor fast booting.
Initializing Video InterfaceThis will start detecting CPU clock,checking type of video onboard. Then,detect and initialize the video adapter.
D-Bracket 2 ConnectorThis connector is for you to connect to the D-Bracket2 which integrates four LEDs andUSB ports. It allows users to identify system problems through 16 various combinationsof LED signals.
19
D-Bracket 2(Optional)
Connected to D-Bracket 2 connectorConnected to USB connector
-
En-15
Engl
ish
Clear CMOS JumperThere is a CMOS RAM onboard that has a power supply from an external battery to keepthe data of system configuration. With the CMOS RAM, the system can automaticallyboot OS every time it is turned on. If you want to clear the system configuration, set thejumper to clear data.
Power Supply AttachmentBefore inserting the power supply connector, always make sure that all components areinstalled properly to ensure that no damage will be caused. All power connectors onthe mainbnoard have to connect to the ATX power supply and have to work together toensure stable operation of the mainboard.
ATX 24-Pin Power ConnectorThis connector allows you to connect an ATX 24-pin power supply. To connect the ATX24-pin power supply, make sure the plug of the power supply is inserted in the properorientation and the pins are aligned. Then push down the power supply firmly into theconnector.You may use the 20-pin ATX power supply as you like. If youd like to use the 20-pin ATXpower supply, please plug your power supply along with pin 1 & pin 13.
20
Clear Data
Important
You can clear CMOS by shorting 2-3 pin while the system is off. Then return to 1-2 pin position. Avoid clearing the CMOS while the system is on; it will damagethe mainboard.
21
1
12 24
13+3.3V+3.3VGND+5V
GND+5V
GNDPWR OK
5VSB+12V+12V
+3.3V GND+5V+5V+5VNCGNDGNDGNDPS-ON#GND-12V+3.3V
Keep Data (default)
1
3
1
3
1
-
En-16
MS-7369 Mainboard
ATX 12V Power Connector (2x2-Pin)This 12V power connector is used to provide power to the CPU.
ATX 12V Power Connector (2x4-Pin)This 12V power connector is used to provide power to the CPU.
ATX 12V Power Connector (1x4-Pin)This 12V power connector is used to provide power to the graphics card.
8 4
15GNDGNDGNDGND
+12V+12V+12V+12V
4
21
3
5VGNDGND12V
ATX 20-Pin Power ConnectorThis connector allows you to connect an ATX 20-pin power supply. To connect the ATX20-pin power supply, make sure the plug of the power supply is inserted in the properorientation and the pins are aligned. Then push down the power supply firmly into theconnector.
1
10 20
113.3V3.3V
GND5V
GND5V
GNDPWR OK
5VSB12V 5V
5V-5VGNDGNDGNDPS-ONGND-12V3.3V
22
23
24
25
13
4 2GND12V
12V GND
-
En-17
Engl
ish
PCI Express Slot (x16/ x4/ x1)The PCI Express slot supports the PCI Express interface expansion card.The PCI Express x 16 supports up to 4.0 GB/s transfer rate.The PCI Express x 8 supports up to 2.0 GB/s transfer rate.The PCI Express x 4 supports up to 1.0 GB/s transfer rate.The PCI Express x 1 supports up to 250 MB/s transfer rate.
PCI Express x 16 Slot
PCI Express x 4 Slot
PCI Express x 1 Slot
PCI (Peripheral Component Interconnect) SlotThe PCI slot supports LAN card, SCSI card, USB card, and other add-on cards thatcomply with PCI specifications.
AGP (Accelerated Graphics Port) SlotThe AGP slot allows you to insert the AGP graphics card. AGP is an interface specifica-tion designed for the throughput demands of 3D graphics. It introduces a 66MHz, 32-bitchannel for the graphics controller to directly access main memory.
26
27
28
Important
When adding or removing expansion cards, make sure that you unplug the powersupply first. Meanwhile, read the documentation for the expansion card to configureany necessary hardware or software settings for the expansion card, such asjumpers, switches or BIOS configuration.
-
En-18
MS-7369 Mainboard
Back PanelMouse/Keyboard
The standard PS/2 mouse/keyboard DIN connector is for a PS/2 mouse/keyboard.
Parallel PortA parallel port is a standard printer port that supports Enhanced Parallel Port (EPP) andExtended Capabilit ies Parallel Port (ECP) mode.
Serial PortThe serial port is a 16550A high speed communications port that sends/ receives 16bytes FIFOs. You can attach a serial mouse or other serial devices directly to theconnector.
VGA PortThe DB15-pin female connector is provided for monitor.
(9-Pin Male Connector)
1 5
6 9
A
B
C
D
PS/2 Mouse connector (Green/ 6-pin female)
PS/2 Keyboard connector (Purple/ 6-pin female)
13 1
1425
(25-pin female connector)
(15-Pin Female DIN Connector)
15
1115
-
En-19
Engl
ish
1394 PortThe IEEE1394 port on the back panel provides connection to IEEE1394 devices.
DVI-D PortThe DVI-D (Digital Visual Interface Digital) connector allows you to connect an LCDmonitor. It provides a high-speed digital interconnection between the computer and itsdisplay device. To connect an LCD monitor, simply plug your monitor cable into the DVIconnector, and make sure that the other end of the cable is properly connected to yourmonitor (refer to your monitor manual for more information.)
1
2417
8
Important
Please note that the DVI connector does not support connecting the DVI-D to D-sub converter.
LANThe standard RJ-45 LAN jack is for connection to the Local Area Network (LAN). You canconnect a network cable to it.
LED Color LED State Condition
Off LAN link is not established.
Left Orange On (steady state) LAN link is established.
On (brighter & pulsing) The computer is communicating with another computer on the LAN.
Green Off 10 Mbit/sec data rate is selected.
Right On 100 Mbit/sec data rate is selected.
Orange On 1000 Mbit/sec data rate is selected.
E
F
G
-
En-20
MS-7369 Mainboard
USB PortThe USB (Universal Serial Bus) port is for attaching USB devices such as keyboard,mouse, or other USB-compatible devices.
Audio Port ConnectorsThese audio connectors are used for audio devices. You can differentiate the color ofthe audio jacks for different audio sound effects.
Line-Out (Green) - Line Out, is a connector for speakers or headphones.Line-In (Blue) - Line In, is used for external CD player, tapeplayer or other audiodevices.MIC (Pink) - Mic In, is a connector for microphones.CS-Out (Orange) - Center/ Subwoofer Out in 5.1/ 7.1 channel mode.RS-Out (Black) - Rear-Surround Out in 4/ 5.1/ 7.1 channel mode.SS-Out (Gray) - Side-Surround Out 7.1 channel mode.
Coaxial S/PDIF-outThis S/PDIF (Sony & Philips Digital Interconnect Format) connector is provided fordigital audio transmission to external speakers through a coaxial cable.
Optical S/PDIF-outThis S/PDIF (Sony & Philips Digital Interconnect Format) connector is provided fordigital audio transmission to external speakers through an optical fiber cable.
H
IJ
KL
NM
O
P
HDMI PortThe High-Definition Multimedia Interface (HDMI) is an all-digital audio/video interfacecapable of transmitting uncompressed streams. HDMI supports all TV format, includingstandard, enhanced, or high-definition video, plus multi-channel digital audio on asingle cable.
Q
-
En-21
Engl
ish
BIOS Setup
This chapter provides basic information on the BIOS Setup program and allows you toconfigure the system for optimum use. You may need to run the Setup program when:* An error message appears on the screen during the system booting up, and requests
you to run BIOS SETUP.* You want to change the default settings for customized features.
Important
1. The items under each BIOS category described in this chapter are undercontinuous update for better system performance. Therefore, the descriptionmay be slightly different from the latest BIOS and should be held for referenceonly.
2. Upon boot-up, the 1st line appearing after the memory count is the BIOSversion. It is usually in the format:
A7369NMS V1.0 061507 where:1st digit refers to BIOS maker as A = AMI, W = AWARD, and P = PHOENIX.2nd - 5th digit refers to the model number.6th refers to the Chipset vender as A = ATi, I = Intel, V = VIA, N = Nvidia, U = ULi.7th - 8th digit refers to the customer as MS = all standard customers.V1.0 refers to the BIOS version.061507 refers to the date this BIOS was released.
-
En-22
MS-7369 Mainboard
Entering SetupPower on the computer and the system will start POST (Power On Self Test) process.When the message below appears on the screen, press key to enter Setup.
Press DEL to enter SETUPIf the message disappears before you respond and you still wish to enter Setup, restartthe system by turning it OFF and On or pressing the RESET button. You may also restartthe system by simultaneously pressing , , and keys.
Getting HelpAfter entering the Setup menu, the first menu you will see is the Main Menu.
Main MenuThe main menu lists the setup functions you can make changes to. You can use thearrow keys ( ) to select the item. The on-line description of the highlighted setupfunction is displayed at the bottom of the screen.
Sub-MenuIf you find a right pointer symbol (as shown in the right view)appears to the left of certain fields that means a sub-menucontaining additional opt ions can be launched from thisfield. You can use control keys ( ) to highlight the fieldand press to call up the sub-menu. Then you canuse the control keys to enter values and move from field to field within a sub-menu. Ifyou want to return to the main menu, just press .
General Help The BIOS setup program provides a General Help screen. You can call up this screenfrom any menu by simply pressing . The Help screen lists the appropriate keys touse and the possible selections for the highlighted item. Press to exit the Helpscreen.
-
En-23
Engl
ish
Standard CMOS FeaturesUse this menu for basic system configurations, such as time, date etc.Advanced BIOS FeaturesUse this menu to setup the items of special enhanced features.Integrated PeripheralsUse this menu to specify your settings for integrated peripherals.Power Management FeaturesUse this menu to specify your settings for power management.PNP/PCI ConfigurationsThis entry appears if your system supports PnP/PCI.H/W MonitorThis entry shows your PC health status.Frequency/ Voltage ControlUse this menu to specify your settings for fequency/voltage control and overclocking.Load Fail-Safe DefaultsUse this menu to load the default values set by the BIOS vendor for stable systemperformance.Load Optimized DefaultsUse this menu to load the default values set by the mainboard manufacturer specificallyfor optimal performance of the mainboard.BIOS Setting PasswordUse this menu to set the Password.Save & Exit SetupSave changes to CMOS and exit setup.Exit Without SavingAbandon all changes and exit setup.
The Main MenuOnce you enter AMI or AWARD BIOS CMOS Setup Utility, the Main Menu will appearon the screen. The Main Menu allows you to select from ten setup functions and two exitchoices. Use arrow keys to select among the items and press to accept or enterthe sub-menu.
-
En-24
MS-7369 Mainboard
When enter the BIOS Setup utility, follow the processes below for general use.1. Load Optimized Defaults : Use control keys ( ) to highlight the Load Optimized
Defaults field and press , a message as below appears:
Press [Ok] to load the default settings for optimal system performance.
2. Setup Date/ Time : Select the Standard CMOS Features and press to enterthe Standard CMOS Features-menu. Adjust the Date, Time fields.
3. Save & Exit Setup : Use control keys ( ) to highlight the Save & Exit Setup fieldand press , a message as below appears:
Press [Ok] to save the configurations and exit BIOS Setup utility.
Important
The configuration above are for general use only. If you need the detailedsettings of BIOS, please see the manual in English version on MSI website.
-
En-25
Engl
ish
Software Information
Take out the Driver/Utility CD that is included in the mainboard package, and place itinto the CD-ROM driver. The installation will auto-run, simply click the driver or utilt iyand follow the pop-up screen to complete the installation. The Driver/Utility CD con-tains the:Driver menu - The Driver menu shows the available drivers. Install the driver by your desire and to activate the device.Utility menu - The Utility menu shows the software applications that the mainboard supports.WebSite menu- The WebSite menu shows the necessary websites.
Important
Please visit the MSI website to get the latest drivers and BIOS for better systemperformance.
-
De-1
Deu
tsch
K9N Neo V2/ V3Benutzerhandbuch
Deutsch
-
De-2
MS-7369 Mainboard
Spezifikationen
Prozessoren- AMD Athlon 64/ 64X2 & Sempron fr Socekel AM2(Weitere CPU Informationen finden Sie unter http://global.msi.com.tw/index.php?func=cpuform)
HyperTransport (HT)- Untersttzt eine Hochgeschwindigkeitsverbindung von bis zu
1 GHz (2000MT/s) ber den HyperTransport
Chipsatz- NVIDIA nForce 520 (K9N Neo V2)- NVIDIA nForce 560 (K9N Neo V3)
Speicher- DDR2 533/667/800 SDRAM (240Pin/ non-ECC)- 4 DDR2 DIMMs (max. 8GB)(W eitere Informationen zu kompatiblen Speichermodulen findenSie unter http://global.msi.com.tw/index.php?func=testreport)
LAN- Untersttzt Giga LAN 10/100/1000 Fast Ethernet ber Realtek RTL8111B/ RTL 8211BL (optional)
Audio- Onboard Realtek ALC888 Soundchip- 7.1-Kanal Audio-Ausgang- Erfl lt die Azalia Spezifikationen
IDE- 1 IDE Port- Untersttzt die Betriebmodi Ultra DMA 66/100/133 und PIO &
Bus Mastering
SATA- 4 SATA Ports- Untersttzt 4 SATA Gerte- Datenbertragungsraten von bis zu 300 MB/s
RAID- SATA1~4 untersttzt die Modi RAID 0/ 1/ 0+1/ 5 oder JBOD
(Die Modi RAID 5 nur fr nForce 560)
-
De-3
Deu
tsch
Disket ten Laufwerk- 1 Disketten Anschluss- Untersttzt ein Diskettenlauferk mit 360KB, 720KB, 1.2MB, 1.
44MB oder 2.88MB Kapazitt
Anschlsse
Hintere Ein-/ und Ausgnge- 1 PS/2 Mausanschluss- 1 PS/2 Tastaturanschluss- 1 Serielle Schnittstelle- 1 Parallele Schnittstelle, untersttzt die Betriebsmodi SPP/EPP/
ECP- 4 USB 2.0 Anschlsse- 1 LAN Buchse- 6 Audiobuchsen
On-Board Stiftleiste/ Anschlsse- 3 USB 2.0 Stiftleisten- 1 Gehusekontaktschalter- 1 SPDIF-Ausgang Stiftleiste- 1 Audio Stiftleiste fr Gehuse Audio Ein-/ Ausgnge- 1 CD Stiftleiste fr Audio EingangSchnittstellen- 1 PCI Express x 16 Schnittstelle- 2 PCI Express x 1 Schnittstellen- 3 PCI Schnittstellen, untersttzt 3.3V/ 5V PCI Bus Interface
Form Faktor- ATX (30.5 cm X 20.0 cm)
Montage- 6 Montagebohrungen
-
De-4
MS-7369 Mainboard
bersicht Eingenschaften der K9N Neo V2/ K9N Neo V3Mainboard Series (MS-7369 v1.X)
1 De-5
ADe-18
BDe-18
CDe-18
G
De-19
HDe-20
J M
I
L
NK
De-20
De-20
De-20
3 De-7
4 De-9
4De-9
21 De-15
6 De-9
7 De-10
8 De-10
10 De-115 De-911
De-1114
De-12
De-1112
20 De-15
15 De-12
27 De-17
26 De-17
23De-16
4De-9
-
De-5
Deu
tsch
Das Mainboard untersttzt AMD Prozessoren und verwendet hierfr einen CPUSockel mit der Bezeichnung Sockel-AM2, um das Einsetzen der CPU zu erleichtern.Verfgen Sie ber keinen Khler, setzen Sie sich bitte mit Ihrem Hndler in Verbindung,um einen solchen zu erwerben und danach zu installieren, bevor Sie Ihren Computeranschalten.Um die neuesten Informationen zu untersttzten Prozessoren zu erhalten, besuchenSie bitte http://global.msi.com.tw/index.php?func=cpuform
1
Hauptprozessor: CPU
Vorgehensweise CPU Einbau beim Sockel AM21. Bitte Schalten Sie das System aus und ziehen Sie den
Netzstecker, bevor Sie die CPU einbauen.2. Ziehen Sie den Hebel leicht seitlich weg vom Sockel,
heben Sie ihn danach bis zu einem Winkel von ca. 90 an.3. Suchen Sie nach einem goldenen Pfeil. Der goldene Pfeil
sollte die gleiche Ausrichtung wie in der Grafik haben. DieCPU passt nur in der korrekten Aus-richtung.
4. Ist die CPU korrekt instal liert, sollten die Pins an derUnterseite vollstndig versenkt und nicht mehr sichtbar sein. Beachten Sie bitte,dass jede Abweichunng von der richtigen Vorgehensweise beim Einbau Ihr Mainboarddauerhaft beschdigen kann.
5. Drcken Sie die CPU fest in den Sockel und drcken Sie den Hebel wieder nachunten bis in seine Ursprungsstellung. Da die CPU whrend des Schlieens desHebels dazu neigt, sich zu bewegen, sichern Sie diese bitte whrend des Vorgangsdurch permanenten Fingerdruck von oben, um sicherzustellen, dass die CPU richtigund vollstndig im Sockel sitzt.
Gold arrow
Correct CPUplacement
Wichtig
berhitzungberhitzung beschdigt die CPU und das System nachhaltig, stellen Sie stetseine korrekte Funktionsweise des CPU Khlers sicher, um die CPU vorberhitzung zu sch tzen. berprfen Sie eine gleichmige Schicht derthermischen Paste (oder thermischen Klebeandes) zwischen der CPU und demKhlblech anwenden, um Wrmeableitung zu erhhen.CPU WechselStellen Sie vor einem Wechsel des Prozessors stets sicher, dass das ATXNetzteil ausgeschaltet und der Netzstecker gezogen ist, um die Unversehrtheitder CPU zu gewhrleisten.bertaktenWir bernehmen keinerlei Garantie fr die Schden und Risiken, die ausunzulssigem oder Betrieb jenseits der Produktspezifikationen resultieren.
-
De-6
MS-7369 Mainboard
Fixed Lever
Installation des KhlersetsWenn Sie die CPU einbauen, stellen Sie bitte sicher, dass Sie auf der CPU einenKhlkrper mit aktiven Prozessorlfter anbringen, um berhitzung zu vermeiden.Verfgen Sie ber keinen aktiven Prozessorlfter, setzen Sie sich bitte mit Ihrem Hndlerin Verbindung, bevor Sie Ihren Computer anschalten.
1. Setzen Sie das Khlerset auf den Rckhaltemechanismus. Haken Sie zuerst einEnde des Haltebgels ein, dann drcken Sie das andere Ende des Bgels herunter,um das Khlerset auf dem Rckhaltemechanismus zu befestigen.
2. Machen Sie den Sicherungshebel, den Sicherungshaken und den Sicherungsbolzenausfindig. Heben Sie den Sicherungshebel an.
3. Drcken Sie den Sicherungshebel herab.4. Stel len Sie sicher, dass der S icherungshaken den Sicherungsbolzen des
Rckhaltemechanismus voll-stndig umfasst.5. Verbinden Sie das Stromkabel des CPU Lfters mit dem Anschluss auf dem Mainboard.
Wichtig
Die Mainboardfotos in diesem Abschnitt dienen nur zur Illustration des CPU/Khlereinbaus. Die Erscheinung Ihres Mainboards kann in Abhngigkeit vomModel abweichen.
-
De-7
Deu
tsch
Speicher
DDRSpezifikation : 184-Pin, 2.5v.Bestimmung Einkanalbetrieb : All DIMM Slots sind GRNE Farbe.Bestimmung Zweikanalbetrieb : Die DIMM Slot(s) des Kanals A sind in GRN gehalten.Die DIMM Slot(s) des Kanals B sind LILA.
DDR2Spezifikation : 240-Pin, 1.8V.Bestimmung Einkanalbetrieb : Alle DIMM Slots sind GRNE Farbe.Bestimmung Zweikanalbetrieb : Die DIMM Slot(s) des Kanals A sind in GRN gehalten.Die DIMM Slot(s) des Kanals B sind ORANGE.
64x2=128 Pin 56x2=112 Pin
40x2=80 Pin 52x2=104 Pin
2
3
Wichtig
- DDR2 und DDR knnen nicht untereinander getauscht werden und der StandardDDR2 ist nicht rckwrtskompatibel, installieren Sie DDR2 Speichermodule stetsin DDR2 DIMM Slots und DDR2 Speichermodule stets in DDR2 DIMM Slots.
- Stellen Sie im Zweikanalbetrieb bitte sicher, dass Sie Module des gleichenTyps und identischer Speicherdichte in den DDR DIMM Slots unterschiedlicherKanle verwenden.
- Um einen sicheren Systemstart zu gewhrleisten, bestcken Sie immer DIMM 1zuerst.
-
De-8
MS-7369 Mainboard
Volt Notch
Vorgehensweise beim Einbau von Speicher ModulenSie finden Kerbe und Stromfhrung (Volt) sowohl an DDR als auch DDR2 Modulen.B efolgen S ie d ie folgenden E inbauh inweise, um d ie DDR/ DDR2 Modu leordnungsgem einzusetzen.
1. Diese Speichermodulen haben nur eine Kerbe in der Mitte des Moduls. Sie passennur in einer Richtung in den Sockel.
2. Setzen Sie den DIMM- Speicherbaustein senkrecht in den DIMM- Sockel, danndrcken Sie ihn hinein, bis die goldenen Kontakte tief im DIMM Sockel sitzen.
3. Die Plastikklammern an den Seiten des DIMM- Sockels schlieen sich automatisch.
Wichtig
Sie knnen den goldenen Finger kaum sehen, wenn das Speichermodule richtigim DIMM Steckplatz eingesetzt wird.
-
De-9
Deu
tsch
Anschlsse, Steckbrcken und Slots
Anschluss des DiskettenlaufwerksDiese Anschluss untersttzt einen Diskettenlaufwerke mit 360KB, 720KB, 1.2MB, 1.44MB oder 2.88MB Kapazitt.
5
Stromanschlsse fr LfterDie Anschlsseuntersttzen aktive Systemlfter mit + 12V. CPU FAN kann Smart FANFunktion untersttzen. Wenn Sie den Anschluss herstellen, sollten Sie immer daraufachten, dass der rote Draht der positive Pol ist, und mit +12V verbunden werden sollte,der schwarze Draht ist der Erdkontakt und sollte mit GND verbunden werden. Ist IhrMainboard mit einem Chipsatz zur berwachung der Systemhardware versehen, dannbrauchen Sie einen speziellen Lfter mit Tacho, um die Vorteile der Steuerung desCPU Lfters zu nutzen.
4
IDE AnschlussDieser Anschluss knnen bis zu IDE Festplatten, optical Diskettenlaufwerke und andereGerte angeschlossen werden.
6
CPU FAN(Lfter)
Wichtig
1. Bitte informieren Sie sich auf der offiziellen Website vom Prozessor berempfohlene CPU Khler oder fragen Sie Ihren Hndler nach einem geeignetenLfter.
2. CPUFAN kann die Lfter mit drei- und vierpolige Stecker untersttzen.3. Der Anschluss CPUFAN1 untersttzt eine aktive Lfterkontrolle Ihres
Prozessorlf ters. Die MSI Dual Core Center Software regelt dieLfterdrehzahl in Abhngigkeit der CPU Temperatur (Software auf CDenthalten).
Wichtig
Verbinden Sie zwei Laufwerke ber ein Kabel, mssen Sie das zweite Laufwerkim Slave-Modus konfigurieren, indem Sie entsprechend den Jumper setzen.Entnehmen Sie bi t te die Anweisungen zum Setzen des Jumpers derDokumentation der IDE Gerte, die der Festplattenhersteller zur Verfgungstellt.
SENSOR+12VGND
Control
SYS FAN/ NB FAN/POWER FAN (System-,Northbridge- und Netzteillfter)
SENSOR+12VGND
-
De-10
MS-7369 Mainboard
Frontpanel AnschlsseDiese Anschlsse sind fr das Frontpanel dienen zum Anschluss der Schalter und LEDsdes Frontpaneels. JFP1 erfllt die Anforderungen des Intel Front Panel I/O Connectiv-ity Design Guide.
8
Serial ATA AnschlussDieser Anschluss ist ein hoch-Geschwindigkeit Schnittstelle der Serial ATA . An jedenconnector can Anschluss kann eine Serial ATA Anschluss angeschlossen werden.
7
Wichtig
Bitte falten Sie das Serial ATA Kabel nicht in einem Winkel von 90 Grad, dadies zu Datenverlusten whrend der Datenbertragung fhrt.
IEEE1394 Anschluss (Grn)Dieser Anschluss erlaubt Ihren,die Vorrichtung IEEE1394 ber ein externes IEEE1394Slotblech anzuschlieen.
9
IEEE1394 Slotblech(Optional)
12
910
HDDLED
ResetSwitch
PowerLED
PowerSwitch
JFP1
Speaker
JFP2
78
PowerLED
12
1 2
9 10
TPA+
Gro
und
TPB
+C
able
pow
erK
ey (n
o pi
n)
TPA
-G
roun
dTP
B-
Cab
le po
wer
Gro
und
-
De-11
Deu
tsch
Audioanschluss des Frontpanels (Azalia Spec)Dieser Anschluss ermglicht den Anschluss von Audioein- und -ausgngen einesFrontpanels. Der Anschluss entspricht den Richtlinien des Intel Front Panel I/O Con-nectivity Design Guide.
12
SPDIF Slotblech (Optional)
11
USB Vorderanschluss (Gelb)Dieser Anschluss entspricht den Richtlinien des Intel I/O Connectivity Design Guide, istbestens geeignet, Hochgeschwindigkeits- USB- Peripheriegerte anzuschlieen, wie z.B. USB Festplattenlaufwerke, Digitalkameras, MP3-Player, Drucker, Modems undhnliches.
10
Bitte beachten Sie, dass Sie die mit VCC (Stromfhrende Leitung) und GND(Erdleitung) bezeichneten Pins korrekt verbinden mssen, ansonsten kann es zuSchden kommen.
Wichtig
USB 2.0 Slotblech(Optional)
USB
OC
10 1 2
VC
CU
SB0
-U
SB0+
GN
DK
ey (n
o pi
n)
VC
CU
SB1
-U
SB1+
GN
D
9
SPDIFO GND
12
910
MIC
_L
MIC
_R
LIN
E o
ut_R
Fron
t_JD
LIN
E o
ut_L
Gro
und
Pres
ence
#M
IC_J
DN
C(N
o pi
n)LI
NE
out
_JD
S/PDIF-Out Anschluss (Optional, fr HDMI Grafikkarten)Der Anschluss S/PDIF (Sony & Philips Digital Interconnect Format) bertrgt digitaleAudiosignale vom Mainboard zur HDMI Grafikkarte.
-
De-12
MS-7369 Mainboard
CD- EingangDieser Anschluss wird fr externen Audioeingang zur Verfgung gestellt.
GehusekontaktanschlussDieser Anschluss wird mit einem Kontaktschalter verbunden. Wird das Gehuse geffnet,wird der Schalter geschlossen und das System zeichnet dies auf und gibt auf demBildschirm eine W arnung aus. Um die W arnmeldung zu lschen, muss das BIOSaufgerufen und die Aufzeichnung gelscht werden.
GND RL
Audioanschluss des Frontpanels (AC97 Spec)Dieser Anschluss ermglicht den Anschluss von Audioein- und -ausgngen einesFrontpaneels. Der Anschluss entspricht den Richtlinien des Intel Front Panel I/OConnectivity Design Guide.
15
1 2
9 10
AUD_MICAUD_MIC_BIAS
AUD_FPout_RHP_ON
AUD_FPout_L
AUD_GNDAUD_VCCAUD_RET_RKeyAUD_RET_L
13
Wichtig
Wenn Sie die vorderen Audioanschlsse nicht verwenden, mssen die Pins 5 &6 und 9 & 10 mit sog. Jumpern gebrckt werden, um die Signalausgabe auf diehinteren Audioanschlsse umzuleiten. Andernfalls ist der Line -Out Ausgang imhinteren Anschlussfeld ohne Funktion.
14
12
CINTRUGND
-
De-13
Deu
tsch
Infrarotmodul StifleisteGestattet zu jeder Zeit den Anschluss eines Infrarotmoduls und entspricht den Richtliniendes Intel Front Panel I/O Connect ivity Design Guide. Sie mssen im BIOS dienotwendigen Einstellungen vornehmen, um die IR Funktion nutzen zu knnen.
Serielle SchnittstelleBei der Anschluss handelt es sich um eine 16550A Hochgeschwindigkeitskommunikations-schnittstelle, die 16 Bytes FIFOs sendet/empfngt. An den Stecker knnen Sie direkteine Serielles Gert anschlieen.
TV- AusgangDer TV- Ausgang dient zum Anschluss eines Slotbleches mit TV- Ausgang. Das Slotblechbietet mehrere Arten von TV Ausgngen. Whlen Sie einen geeigneten, um einFernsehgert anzuschlieen.
65
21NC
VCC5IRTX
NCGroundIRRX
16
17
18
1
9
2DCDSINSOUTDTRGroundDSRRTSCTSRI
5
1 2Ground
YoutCout
COMP or CVBSGround
-
De-14
MS-7369 Mainboard
1
9
2
10
DBG1DBG2DBG3DBG4
Key
DBR1DBR2DBR3DBR4NC
D-Bracket 2 AnschlussDieser Anschluss ist, damit Sie an das D-Bracket 2 anschlieen, das vier LED und USBTore integriert. Es erlaubt Benutzern, System Probleme durch 16 verschiedeneKombinationen der LED Signale zu kennzeichnen.
19
BIOS Anmeldung
Ze i g t i n fo rm a t i one n , Lo go ,Prozessorhersteller, etc...
Test des Basis- und erweitertenSpeichers - Test des Basisspeichersvon 240K bis 640K und des erweitertenSpeichers ber 1MB mit unter-schiedlichen Mustern.
Zuweisung der Resourcen an alleISA Komponenten
Initialisierung FestplattenkontrollerInitialisiert die Festplatte und denKontroller
Initialisierung des Diskettenkon-trollers.
Initialisiert das Diskettenlaufwerkund den Kontroller.
Versuch hoch zu fahren.
Setzt den niedrigen Stapel undbooted ber INT 19h.
Hochfahren des Betriebssystems
System ANDie D-LED bleibt hier stehen, wennder Prozessor beschdigt ist odernicht richtig installiert.
Initialisierung Tastatur Kontroller.
Test VGA BIOS
Hier wird die VGA- Anmeldung amBildschirm angezeigt.
Prozessorinitialisierung
Zeigt Informationen zum Prozessor(wie Name der Marke, Systembus,etc...)
Test der Echtzeituhr (RTC - RealTime Clock)
Description
Rot Grn
LED Signal
1 2
3 4
1 2
3 4
1 2
3 4
1 2
3 4
1 2
3 4
1 2
3 4
1 2
3 4
1 2
3 4
DescriptionLED Signal
1 2
3 4
1 2
3 4
1 2
3 4
1 2
3 4
1 2
3 4
1 2
3 4
1 2
3 4
1 2
3 4
Frhe Initialisierung des Chipsatzes
Speichertest - Test der Gre desSpeichers onboard. Die D-LEDbleibt bei beschdigtem oderfehlerhaft eingesetztem Modulhngen.
Entpacken des BIOS ins RAM zumschnellen Hochfahren.
Initialisierung Video Schnittstelle -startet Erm itt l ung CPU Takt,berprfing Video onboard. DanachErkennung und Initialisierung derGrafiklsung.
D-Bracket 2(Optional)
Verbindungzum JDB1
Verbindung zur USBStiftleiste
-
De-15
Deu
tsch
Steckbrcke zur CMOS- LschungAuf dem Mainboard gibt es einen sogenannten CMOS Speicher (RAM), der ber eineBatterie gespeist wird und die Daten der Systemkonfiguration enthlt. Er ermglicht esdem Betriebssystem, mit jedem Einschalten automatisch hochzufahren. Wollen Sie dieSystemkonfiguration lschen, verwenden Sie hierfr JBAT1 (Clear CMOS Jumper -Steckbrcke zur CMOS Lschung).
Zustzlicher Hinweis StromversorgungBevor Sie eine Verbindung mit den Stromanschlssen herstellen, stellen Sie immersicher, dass alle Komponenten ordnungsgem eingebaut sind, um jegliche Schdenauszuschlieen. Alle Stromanschlsse auf dem Mainboard mssen mit einem ATX Netzteilverbunden werden und mssen gemeinsam den stabilen Betrieb des Mainboards sicherstellen.
ATX 24-Pin StromanschlussHier knnen Sie ein ATX 24-Pin Netzteil anschl ieen. Wenn Sie die Verbindungherstellen, stellen Sie sicher, dass der Stecker in der korrekten Ausrichtung eingestecktwird und die Pins ausgerichtet sind. Drcken Sie dann den Netzteilstecker fest in denSteckersockel.Sie knnen auch ein 20-Pin ATX Netzteil verwenden, wenn Sie mchten. Wenn Sie ein20-Pin ATX Netzteil einsetzen mchten, stecken Sie bitte Ihr Netzteil beginnend beiden PinS 1 und 13 ein.
20
21
1
12 24
13+3.3V+3.3VGND+5V
GND+5V
GNDPWR OK
5VSB+12V+12V
+3.3V GND+5V+5V+5VNCGNDGNDGNDPS-ON#GND-12V+3.3V
Daten lschenDaten erhalten (Werkseinstellung)
Wichtig
Sie knnen den CMOS lschen, indem Sie die Pins 2-3 verbinden, whrend dasSystem ausgeschaltet ist. Kehren Sie danach zur Pinposition 1-2 zurck. LschenSie den CMOS nicht, solange das System angeschaltet ist, dies wrde dasMainboard beschdigen.
1
3
1
3
1
-
De-16
MS-7369 Mainboard
ATX 12V Stromanschluss (2x2-Pin)Dieser 12V Stromanschluss wird verwendet, um die CPU mit Strom zu versorgen.
ATX 12V Stromanschluss (2x4-Pin)Dieser 12V Stromanschluss wird verwendet, um die CPU mit Strom zu versorgen.
ATX 12V Stromanschluss (1x4-Pin)Dieser 12V Stromanschluss wird verwendet, um die Grafikkarte mit Strom zu versorgen.
8 4
15GNDGNDGNDGND
+12V+12V+12V+12V
4
21
3
5VGNDGND12V
ATX 20-Pin StromanschlussHier knnen Sie ein ATX 20-Pin Netzteil anschl ieen. Wenn Sie die Verbindungherstellen, stellen Sie sicher, dass der Stecker in der korrekten Ausrichtung eingestecktwird und die Pins ausgerichtet sind. Drcken Sie dann den Netzteilstecker fest in denSteckersockel.
1
10 20
113.3V3.3V
GND5V
GND5V
GNDPWR OK
5VSB12V 5V
5V-5VGNDGNDGNDPS-ONGND-12V3.3V
22
23
24
25
13
4 2GND12V
12V GND
-
De-17
Deu
tsch
PCI Express Slot (x16/ x4/ x1)Der PCI Express Slot unterstutzt die PCI Express Schnittstelle Erweiterungskarten.Der PCI Express x 16 unterstutzt die Datenubertragunsraten von bis zu 4.0 GB/s.Der PCI Express x 8 unterstutzt die Datenubertragunsraten von bis zu 2.0 GB/s.Der PCI Express x 4 unterstutzt die Datenubertragunsraten von bis zu 1.0 GB/s.Der PCI Express x 1 unterstutzt die Datenubertragunsraten von bis zu 250 MB/s.
PCI Express x 16 Slot
PCI Express x 4 Slot
PCI Express x 1 Slot
PCI (Peripheral Component Interconnect) SlotDie PCI Steckpltze unterst tzt LAN Karte, SCSI Karte, USB Karte und andereZusatzkarten cards,die mit PCI Spezifikationen bereinstimmen.
AGP (Accelerated Graphics Port) SlotDer AGP Steckplatz gestattet Ihnen den Einsatz von AGP Grafikkarten. AGP ist eineSchnittstellenspezifikation, die gem den Anforderungen von 3D Grafiken an denDatendurchsatz entwickelt wurde. Mit ihr hat die direkte Anbindung des Grafikkontrollersan den Hauptspeicher mit mit 66MHz getakteten 32-Bit Kanal Einzug gehalten.
26
27
28
Wichtig
Stellen Sie vor dem Einsetzen oder Entnehmen von Karten sicher, dass Sie denNetzs t ec ker gezogen haben. S t ud ie ren Sie b i t t e d ie A n lei t ung zurErweiterungskarte, um jede notwendige Hard - oder Softwareeinstellung fr dieErweiterungskarte vorzunehmen, sei es an Steckbrcken (Jumpern), Schalternoder im BIOS.
-
De-18
MS-7369 Mainboard
Hinteres AnschlusspanelMaus-/Tastatur
Die Standard PS/2 Maus/Tastatur Stecker Mini DIN ist fr eine PS/2 Maus/Tastatur .
Parallele SchnittstelleDie Parallele Schnittstelle ist eine Standard Druckerschnittstelle, die ebenso als En-hanced Parallel Port (EPP) und als Extended Capabilities Parallel Port (ECP) betriebenwerden kann.
Serielle SchnittstelleBei der Seriellen Schnittstelle handelt es sich um eine 16550A Hochgeschwindigkeits-kommunikationsschnittstelle, die 16 Bytes FIFOs sendet/empfngt. An den Stecker knnenSie direkt eine Serielle Maus oder ein anderes Serielles Gert anschlieen.
VGA AnschlussDie DB 15-Pin Buchse dient zum Anschluss eines VGA Monitors.
(15-Pin DIN Buchse)
15
1115
A
B
C
D
PS/2 Mausanschluss (Grn/ 6-Pin Buchse)
PS/2 Tastaturanschluss (Lila/ 6-Pin Buchse)
13 1
1425
(25-Pin Centronics Anschlussbuchse)
(9-Pin DIN Steckeranschluss)
1 5
6 9
-
De-19
Deu
tsch
1394 PortDas IEEE 1394 Port auf der hintere Anschlusspanel zu den Vorrichtungen IEEE1394.
DVI-D PortDer DVI (Digital Visual Interface-Digital) Anschluss erlaubt Ihnen, einen LCD Monitoranzuschlieen. Es stellt eine digitale Hochgeschwindigkeitsverbindung zwischem demComputer und dem Bildschirm her. Um einen LCD Monitor anzuschlieen, verbindenSie dessen Stecker einfach mit dem DVI Anschluss des Mainboards und stellen Siesicher, dass das andere Ende des Kabels ordnungsgem mit dem Monitor verbundenist.(Weitere Informationen knnen Sie dem Handbuch Ihres Monitors entnehmen.)
1
2417
8
Wichtig
Bitte beachten Sie, dass dieser DVI Anschluss keinen D-Sub Anschluss bereinen DVI Konverter zulsst.
LANDie Standard RJ-45 Buchse ist fr Anschlus zum an ein Lokales Netzwerk (Local AreaNetwork - LAN). Hier kann ein Netzwerkkabel angeschlossen werden.
LED Farbe LED Status Zustand
Aus Keine Verbindung mit dem LAN.
Links Orange An (Dauerleuchten) Verbindung mit dem LAN.
An (heller & pulsierend) Der Computer kommuniziert mit einem anderen Rechner im LAN.
Grn Aus Gewhlte Datenrate 10 MBit/s.
Rechts An Gewhlte Datenrate 100 MBit/s.
Orange An Gewhlte Datenrate 1000 MBit/s.
G
F
E
-
De-20
MS-7369 Mainboard
USB PortDieser USB (Universal Serial Bus) Anschluss zum direkten Anschluss von USB- Gerten,wie etwa Tastatur, Maus oder weiterer USB-kompatibler Gerte.
AudioschnittstellenDiese Audioanschlsse werden im Zusammenspiel mit Audioein-/ ausgabegertenverwendet . Anhand der Farbe der Audiobuchsen kann man unterschiedl icheVerwendungen unterscheiden.
Line-Ausgang (Grn) - Line Ausgang, fr Lautsprecher und Kopfhrer.Line-Eingang (Blau) - Line Eingang , kann fr externe CD oder Kasettenspieler oderandere Audiogerte verwendet werden.MIK (Pink) - Mikrofon, fr Mikrofoneingang.CS-Ausgang (Orange) - Center-/ Subwooferausgang im 5.1/ 7.1 Kanalbetrieb.RS-Ausgang (Schwarz) - Hinteres Surroundsignal im 4/ 5.1/ 7.1 Kanalbetrieb.SS-Ausgang (Grau) - Seitlichen Surroundsignal im 7.1 Kanalbetrieb.
Koaxialer S/PDIF- AusgangDieser S/PDIF (Sony & Philips Digital Interconnect Format) Ausgang dient als digitaleSchnittstelle zur Audioausgabe zur den externen Lautsprechern durch ein Koaxialkabel.
Optischer S/PDIF-AusgangDieser S/PDIF (Sony & Philips Digital Interconnect Format) Ausgang dient als digitaleSchnittstelle zur Audioausgabezur den externen Lautsprechern durch ein optischenFasernkabel.
H
IJ
K
LMN
P
O
HDMI-Port (optional)High Definition Multimedia (kurz HDMI) ist eine neu entwickelte Schnittstelle fur dievolldigitale Ubertragung von Audio- und Video-Daten (Musik, Filme; Verbindung desPC zum Monitor).HDMI wurde von der Industrie zielgerichtet fur den Bereich der privat genutztenUnterhaltungselektronik (engl. "home entertainment") eingefuhrt.
Q
-
De-21
Deu
tsch
BIOS Setup
Dieses Kapitel enthlt Informationen ber das BIOS Setup und ermglicht es Ihnen, IhrSystem optimal auf Ihre Anforderungen einzustellen. Notwendigkeit zum Aufruf desBIOS besteht, wenn:* Whrend des Bootvorgangs des Systems eine Fehlermeldung erscheint und Sie zum
Aufruf des BIOS SETUP aufgefordert werden.* Sie die Werkseinstellungen zugunsten individueller Einstellungen ndern wollen.
Wichtig
1. Die Menpunkte jeder BIOS Kategorie, die in diesem Kapitel beschriebenwird, werden permanent auf den neues ten Stand gebracht , um dieSystemleistung zu verbessern. Aus diesem Grunde kann die Beschreibunggeringfgig von der aktuellsten Version des BIOS abweichen und solltedementsprechend lediglich als Anhaltspunkt dienen.
2. Whrend des Hochfahrens, wird die BIOS Version in der ersten Zeile nach demHochzhlen des Speichers angezeigt, blicherweise im Format dieses Beispiels:
A7369NMS V1.0 061507 wobei:Die erste Stellen den BIOS-Hersteller bezeichnet, dabei gilt A = AMI, W = AWARD,und P = PHOENIX.2te - 5te Stelle bezeichnet die Modelnummer.6te Stelle bezeichnet den Chipsatzhersteller, A = ATi, I = Intel, V = VIA, N =Nvidia, U = ULi.7te - 8te Stelle bezieht sich auf den Kunden, MS=alle Standardkunden.V1.0 bezieht sich auf die BIOS Version.061507 bezeichnet das Datum der Verffentlichung des BIOS.
-
De-22
MS-7369 Mainboard
Aufruf des BIOS SetupsNach dem Einschalten beginnt der Computer den POST (Power On Self Test -Selbstberprfung nach Anschalten). Sobald die Meldung unten erscheint, drcken Siedie Taste () um das Setup aufzurufen.
Press DEL to enter SETUPWenn die Nachricht verschwindet, bevor Sie reagieren und Sie mchten immer nochins Setup, starten Sie das System neu, indem Sie es erst AUS- und danach wiederANSCHALTEN, oder die RESET-Taste am Gehuse bett igen. Sie knnen das Sys-tem auerdem neu starten, indem Sie gleichzeitig die Tasten , und drcken (bei manchen Tastaturen , und ).
Hilfe findenNach dem Start des Setup Mens erscheint zuerst das Hauptmen.
HauptmenDas Hauptmen l istet Funkt ionen auf, die Sie ndern knnen. Sie knnen dieSteuertasten ( ) verwenden, um einen Menpunkt auszuwhlen. Die Online-Beschreibung des hervorgehobenen Menpunktes erscheint am unteren Bildschirmrand.
UntermensW enn Sie an der l inken Sei te bestimmter Felder einDreieckssymbolf finden (wie rechts dargestellt), bedeuted dies,dass Sie ber das entsprechende Feld ein Untermen mit zustzlichen Optionen aufrufenknnen. Durch die Steuertasten ( ) nnen Sie ein Feld hervorheben und durchDrcken der Eingabetaste in das Untermen gelangen. Dort knnen Sie mitden Steuertasten Werte eingeben und navigieren. Durch Drcken von kommenSie zurck ins Hauptmen.
Allgemeine Hilfe Das BIOS Setup verfgt ber eine Allgemeine Hilfe (General Help). Sie knnen dieseaus jedem Men einfach durch Drcken der Taste aufrufen. Sie listet die Tastenund Einstellungen zu dem hervorgehobenen Menpunkt auf. Um die Hilfe zu verlassen,drcken Sie .
-
De-23
Deu
tsch
Standard CMOS FeaturesIn diesem Men knnen Sie die Basiskonfiguration Ihres Systems anpassen, so z.B.Uhrzeit, Datum usw.Advanced BIOS FeaturesVerwenden Sie diesen Menpunkt, um weitergehende Einstellungen an Ihrem Systemvorzunehmen.Integrated PeripheralsVerwenden Sie dieses Men, um die Einstellungen fr in das Board integriertePeripheriegerte vorzunehmen.Power Management FeaturesVerwenden Sie dieses Men , um die Einstellungen fr die Stromsparfunkt ionenvorzunehmen.PNP/PCI ConfigurationsDieser Eintrag erscheint, wenn Ihr System Plug and Play- Gerte am PCI- Bus untersttzt.H/W MonitorDieser Eintrag zeigt den generellen Systemstatus.Frequency /Voltage ControlHier knnen Sie ihre Einstellungen zur Kontrolle von Frequenz und Spannung und zurbertaktung vornehmen.Load Fail-Safe DefaultsIn diesem Men knnen Sie die werkseitigen Einstellung des BIOS fr einenstabilen Betrieb laden.Load Optimized DefaultsI n d iesem Men kn nen S ie d ie B I O S -Vorein st e l l un gen l aden, d ie d erMainboardhersteller zur Erzielung der besten Systemleistung vorgibt.BIOS Setting PasswordVerwenden Sie dieses Men, um das Kennwort fr das BIOS einzugeben.Save & Exit SetupAbspeichern der BIOS-nderungen im CMOS und verlassen des BIOS.Exit Without SavingVerlassen des BIOS ohne Speicherung, vorgenommene nderungen verfallen.
Das HauptmenNachdem Sie das AMI oder AWARD BIOS CMOS Setup Utility, aufgerufen haben,erscheint das Hauptmen. Es weist zehn Setup- Funktionen und zwei Arten das Men zuverlassen auf. Verwenden Sie die Pfeiltasten, um im Men zu navigieren und drckenSie die Eingabetaste (), um ein Untermen aufzurufen.
-
De-24
MS-7369 Mainboard
Wenn hereinkommen Sie, grnden das BIOS Dienstprogramm, folgen Sie den Prozessenunten fr allgemeinen Gebrauch.1. Last optimierte Rckstellungen : Die Gebrauchsteuerschlssel ( ),, zum der Last
optimierten Rckstellungen hervorzuheben fangen auf und bettigen ,eine Anzeige wie erscheint unten:
Drcken Sie [ok], um die Standardannahmen fr optimale System Leistung zu laden.
2. Einstellung Datum/ Zeit : Whlen Sie die Standard-CMOS Eigenschaften vor undbett igen Sie um das Standard-CMOS Eigenschaft -Men einzutragen.Justieren Sie das Datum, Zeit fngt auf.
3. Auer u. Ausgang Einstellung : Die Gebrauchsteuerschlussel ( ), zum der Aueru. Ausgang Einstellung hervorzuheben fangen auf und bettigen , eineAnzeige wie erscheint unten:
Drcken Sie [ok], um die Konfigurationen speichern und das BIOS Einstellung Dienstprogramm herausnehmen.
Die Konfiguration oben dienen nur generellen Zwecken. Wenn Sie detaillierteBIOS- Einstellungen bentigen, dann sehen Sie bitte das Handbuch in EnglischerSprache auf der MSI Website ein.
Wichtig
-
De-25
Deu
tsch
Software-Informationen
Nehmen Sie den Treiber herausGebrauchs-CD, die im mainboard Paket eingeschlossenist, und setzen Sie es in den CD-ROM Treiber. Die Installation wird Automobil-laufenlassen, klicken Sie einfach den Treiber oder utiltiy und folgen Sie dem pop-up Schirm,um die Installation durchzufhren. Der TreiberGebrauchs-CD enthlt:Treibermen - das Treibermen zeigt die vorhandenen Treiber. Bringen Sie den Treiber
durch Ihren Wunsch und die Vorrichtung zu aktivieren an.Gebrauchsmenmen - das Gebrauchsmen zeigt die SoftwareAnwendungen das die
mainboard Untersttzungen.WebSite Men - das W ebsite Men zeigt die notwendigen Website.
Wichtig
Besichtigen Sie bitte die MSI Website, um die neuesten Treiber und BIOS frbessere System Leistung zu erhalten.
-
Fr-1
Fran
ais
K9N Neo V2/ V3Guide dUtilisation
Franais
-
Fr-2
La Carte mre MS-7369
Spcificits
Processeurs Supports- Processeurs AMD Athlon 64/ 64X2 et Sempron dans le paquet
de socket AM2(Pour plus dinformation sur le CPU, veuillez visiter http://global.msi.com.tw/index.php?func=cpuform)
FSB support- HyperTransport supporte la vitesse jusqu 1 GHz (2000MT/s)
Chipset- Chipset nVidia nForce 520/ nForce 560
Mmoire Support- DDR2 533/667/800 SDRAM (240pin/ non-ECC)- 4 DDR2 DIMMs (8GB Max)
(Pour plus d information sur les connecteurs compatibles, veuillezvisiter http://global.msi.com.tw/index.php?func=testreport)
LAN- Supporte Giga LAN 10/100/1000 Fast Ethernet par Realtek
RTL8111B/ RTL8211BL (optionnel)
Audio- Control par Realtek ALC888- Supporte canaux audio 7.1- Compatible avec Azalia Spec
IDE- 1 port IDE- Supporte Ultra DMA 66/100/133, PIO et le mode Bus Master
operation
SATA- 4 ports SATA supporte 4 devices SATA- Supporte un stockage et un taux de tranfert jusqu 300MB/s
RAID- SATA1~4 supporte RAID 0/ 1/ 0+1/ 5 or JBOD mode (RAID 5
mode seulement pour nForce 560)
-
Fr-3
Fran
ais
Disquet te- 1 port de disquette- Supporte 1 FDD avec 360KB, 720KB, 1.2MB, 1.44MB et 2.88MB
Connecteurs
Panneau arrire- 1 port souris PS/2- 1 port clavier PS/2- 1 port Serial- 1 port parallle supportant les modes SPP/EPP/ECP- 4 ports USB 2.0- 1 jack LAN- 6 jacks audio
Connecteurs intgrs- 3 connecteurs USB 2.0- 1 connecteur Chassis Intrusion Switch- 1 connecteur SPDIF-Out- 1 connecteur Audio avant- 1 connecteur CD-InSlots- 1 slot PCI Express x 16- 2 slots PCI Express x 1- 3 slots PCI, supporte interface bus PCI 3.3V/ 5V
Dimension- ATX (30.5 cm X 20.0 cm)
Montage- 6 trous de montage
-
Fr-4
La Carte mre MS-7369
Guide des composants de la K9N Neo V2/ K9N Neo V3 SriesLa carte mre (MS-7369 v1.X)
1 Fr-5
AFr-18
BFr-18
CFr-18
G
Fr-19
HFr-20
J M
I
L
NK
Fr-20
Fr-20
Fr-20
3 Fr-7
4 Fr-9
4Fr-9
21 Fr-15
6 Fr-9
7 Fr-10
8 Fr-10
10 Fr-115 Fr-911
Fr-1114
Fr-12
Fr-1112
20 Fr-15
15 Fr-12
27 Fr-17
26 Fr-17
23Fr-16
4Fr-9
-
Fr-5
Fran
ais
La carte mre supporte le processeur AMD. Elle ut ilise un Socket-AM2 pourlinstallation.Si vous ne possdez pas de systme de refroidissement du CPU, contactezvotre revendeur pour vous en procurer un et installet le avant dallumer lordinateur.Pour plus d informations, veuillez consulter: ht tp:/ /global.msi.com.tw/ index.php?func=cpuform
1
Central Processing Unit: CPU
Procdure dinstallation du CPU pour Socket AM2:
1. Veuillez teindre et dbrancher votre PC avantlinstallation du CPU.
2. Tirez le levier vers le haut. Assurez-vous que celui-ci estbien en position ouverte maximum (angle de 90)
3. Reprez la flche dore. La flche dore doit se trouvercomme indiqu sur le dessin. Le CPU ne peut treinstaller que dans un seul sens.
4. Si le CPU est correctement install alors les broches ne sont plus visibles. Unemauvaise installation pourrait entraner des dommages vis--vis de la carte mre.
5. Appuyez sur le CPU pendant que vous abaissez le levier. Il faut toujours exercerune pression sur le CPU pour viter que ce dernier ne soit pas bien fix une fois lelevier abaiss.
Gold arrow
Correct CPUplacement
Important
SurchauffeUne surshauffe peut srieusement endommager le CPU et le systme, assurezvous toujours que le systme de refroidissement fonctionne correctement pourprotger le CPU dune surchauffe. Assurez-vous davoir une couche de ptethermique (ou bande thermique) entre le CPU et le heatsink pour aml iorer ladissipation de chaleur.
Remplacer le CPUAvant de remplacer le CPU, teignez toujours lalimentation ATX ou dbranchezla prise pour assurer la scurit du CPU.OverclockingNous ne garantissons pas les dommages ou les risques causs par une oprationinsatisfaisante ou au-del des spcifications du produit.
-
Fr-6
La Carte mre MS-7369
Installation de CPU CoolerLors de linstallation du CPU, assurez-vous de bien installer un radiateur et unventilateur afin dviter la surchauffe. Si vous ne savez pas le modle quil vous faut,il est recommand de prendre contact avec votre revendeur.
1. Positionnez le systme de reffroidissement sur le mcanisme dattache.Accrochez une extrmit de laggrafe avant de tout accrocher.
2. Localisez le levier de fixation, et accrochez le bien sur son encoche.3. Fixez le levier vers le bas.4. Assurez vous que le crochet de scurit soit bien attach son encche sur le
mcanisme.
Fixed Lever
Les photos de la carte mre montres dans cette section sont pour ladmonstration de linstallation plus frache seulement pour le CPU. Laspect devotre carte mre peut changer selon le modle achet par vous.
Important
-
Fr-7
Fran
ais
Mmoire
DDRSpcificit : 184-pin, 2.5v.Dfinition du canal unique : Tous les slots DIMM sont Verts.Dfinition des canaux double : Slot(s) DIMM sur le canal A est en Vert. Slot(s) DIMM surle canal B est en violet .
DDR2Spcification : 240-pin, 1.8v.Dfinition du canal : Tous les slots DIMM sont Verts.Dfinition de canaux double: Slot(s) DIMM sur le canal A est en Vert. Slot(s) DIMM surle canal B est en Orange .
64x2=128 pin 56x2=112 pin
40x2=80 pin 52x2=104 pin
2
3
Important
- Les modules DDR2 ne sont pas interchangeables avec la DDR et le standard DDR2 nest pas compatible en arrire, vous devez toujours installer le module de la mmoire DDR2 dans la fente de DDR2 DIMM et la DDR dans la fente de DDR DIMM.- En mode canal double, assurez-vous bien dinstallez les modules de mmoire du mme type et de mme densit dans les diffrentes fentes du canal DDR DIMM.- Pour que le systme russi son initialisation-up, insrez les modules de mmoire dans le DIMM1 dabord.
-
Fr-8
La Carte mre MS-7369
Installation des Modules de Mmoire:Vous pouvez trouver lentaille sur les modules de mmoire et le volt sur les fentes de DIMM pourla DDR ou DDR2. Suivez les procdures ci-dessous pour installer le Module DDR/ DDR2correctement.1. Le module de mmoire ne possde quune encoche en son centre. Le module ne peut tre
mont que dans le bon sens.2. Insrez le module de mmoire DIMM verticalement dans le slot. Poussez-alors le dedans
jusqu' ce que le doigt d'or sur le module de mmoire soit profondment insr dans ladouille.
3. Le clip en plastique situ de chaque cot du module va se fermer automatiquement.
Volt Entaille
Important
Vous ne pouvez pas voir le doigt dor si le module de la mmoire nest pas insrcorrectement dans le slot DIMM.
-
Fr-9
Fran
ais
Connecteurs, Cavaliers, Slots
Connecteur Pilote de la DisquetteLa carte mre est pourvue dun connecteur de disquette qui supporte les disques de360K, 720K, 1.2M, 1.44M et 2.88M.
5
Connecteurs Alimentation du Ventilateur:Les connecteurs au systme du ventilateur supportent la puissance du ventilateur avec+12V. Le CPUFAN1 du CPU supporte la fonctione Smart FAN. Quand vous reliez le filaux connecteurs, notez que le fil rouge est positif et doit tre reli au +12V, le fil noirest rectifi et mis terre. Si la carte mre a un chipset intgr sur le moniteur dematriel du systme, vous devez utiliser un ventilateur particulier avec une sonde devitesse pour bien contler le ventilateur.
SYS FAN/ NB FAN/POWER FAN
4
Connecteru IDECette carte mre fournit un connecteur IDE qui supporte les lecteurs de disque dur, leslecteursCD-ROM et les autres dispositifs IDE.
6
CPU FAN
Important
Si vous installez 2 disques durs sur une mme nappe, vous devez configurer lesecond disque en mode Slave (esclave) en bougeant les cavaliers. Pour cela, ilfaut vous reporter la documentation du disque dur concernant le changement decavalier (jumpers).
SENSOR+12VGND
Control SENSOR+12VGND
Important
1.Veuillez rfrer-vous au ventilateur du CPU recommend dans le site webofficiel ou contactez au revendeur pour le ventilateur correct du CPU.
2.Ventilateur/radiateur avec 3 ou 4 pins sont disponibles pour CPUFAN.3.CPUFAN supporte la fonction contrler le ventilateur, vous pouvez le
configurer dans le BIOS, ou vous pouvez installer lutilitaire Dual CoreCenter qui contlera la vitesse du ventilateur du CPU automatiquementselon la temperature.
-
Fr-10
La Carte mre MS-7369
Connecteurs panneau en faadeLa carte mre possde deux connecteurs pour la connexion lectrique du panneauavant (LED, switch). JFP1 est compatible avec lIntel Front Panel I/O ConnectivityDesign Guide.
8
9
Connecteur Srie ATALe connecteur SATA supporte le port Serial ATA de hautes performances. Chaqueconnecteur de SATA peut se connecter un disque dur.
7
Important
Veuillez ne pas tordre le cble Srie ATA 90 degrs, cela entranera la pertede donnes lors des phases de transfert.
Connecteur IEEE 1394 (Vert)La carte comporte un connecteur 1394 qui vous permet la connexion de bracketexternes IEEE1394.
IEEE1394 Bracket(Optionnel)
12
910
HDDLED
ResetSwitch
PowerLED
PowerSwitch
JFP1
Speaker
JFP2
78
PowerLED
12
1 2
9 10
TPA+
Gro
und
TPB
+C
able
pow
erK
ey (n
o pi
n)
TPA
-G
roun
dTP
B-
Cab
le po
wer
Gro
und
-
Fr-11
Fran
ais
SPDIF Bracket (Optionnel)
10
Connecteurs panneau en faade (Azalia Spec)Le connecteur vous permet de connecter laudio en faade qui est compatible aveclIntel Front Panel I/O Connectivity Design Guide.
11
12
Connecteur USB en faade (Jaune)Ce connecteur est compatible avec IntelR I/O Connectivity Design Guide, il est idalpour la connexion de matriels possdant une interface USB tel que: disque dur USB,camra digitale, imprimante, lecteur MP3 et bien dautres priphriques.
Important
Notez que les pins de VCC et de GND doivent tre relis correctement pour viterdes dommages possibles.
USB 2.0 Bracket(Optionnel)U
SBO
C
10 1 2
VC
CU
SB0
-U
SB0+
GN
DK
ey (n
o pi
n)
VC
CU
SB1
-U
SB1+
GN
D
9
SPDIFO GND
Le connecteur de sortie S/PDIF (optionnel, pour les cartes graphiques HDMIseulement)Ce connecteur est utilise pour connecter l interface S/PDIF (Format dinterconnexionnumrique Sony et Philips) afin de transmettre le son audio numrique vers les cartesgraphiques HDMI.
12
910
MIC
_L
MIC
_R
LIN
E o
ut_R
Fron
t_JD
LIN
E o
ut_L
Gro
und
Pres
ence
#M
IC_J
DN
C(N
o pi
n)LI
NE
out
_JD
-
Fr-12
La Carte mre MS-7369
Connecteur CD-EntreCes connecteurs permettent laudio input externe..
Connecteur Chassis IntrusionCe connecteur est connect au cble de chassis intrusion switch. Si le chassis est ouvert,le switch en informera le systme, qui enregistrera ce statut et affichera un crandalerte. Pour effacer ce message dalerte, vous devez entrer dans le BIOS et dsactiverl alerte.
GND RL
Connecteurs Audio panneau en faade (AC97 Spec)Le connecteur vous permet de connecter l audio en faade qui est compatible
avec lIntel Front Panel I/O Connectivity Design Guide.
15
1 2
9 10
AUD_MICAUD_MIC_BIAS
AUD_FPout_RHP_ON
AUD_FPout_L
AUD_GNDAUD_VCCAUD_RET_RKeyAUD_RET_L
13
14
Important
Si vous ne voulez pas relier len-tte faade audio les pins 5 et 6, les pins9 et 10 doivent tre jumells afin davoir le rendement de signal dirig versles ports audio arrire. Autrement, le connecteur de Ligne-Sortie sur lepanneau arrire ne fonctionnera pas.
12
CINTRUGND
-
Fr-13
Fran
ais
Connecteur Module InfrarougeCe connecteur permet la mise en place dun module Infrarouge. Vous devez configurercette fonction dans le BIOS afin de pouvoir l utiliser. JIR1 est compatible avec lIntelFront Panel I/O Connectivity Design Guide.
Connecteur Port SrieLe port srie est un port de communication 16550A grande vitesse qui envoie/ reoit16 bytes FIFOs. Vous pouvez directement attacher un dispositif srie au connecteur.
Connecteur TV-SortieLe connecteur SortieTV vous permet dattacher un bracket Sortie-TV. Le bracket TVvous offre plusieurs types de connecteurs de SortieTV. Choisissez le connecteur appropripour vous relier une tlvision.
65
21NC
VCC5IRTX
NCGroundIRRX
16
17
18
3
1 4Ground
YoutCout
COMP or CVBSGround (5)
1
9
2DCDSINSOUTDTRGroundDSRRTSCTSRI
-
Fr-14
La Carte mre MS-7369
1
9
2
10
DBG1DBG2DBG3DBG4
Key
DBR1DBR2DBR3DBR4NC
BIOS ConnectCeci montre des informations sur lelogo, marque et processeur etc...
Essai de la mmoire basse etprolonge.Mmoire basse dessai de 240K 640K et mmoire prolonge plusde1MB en utilisant divers modls.
Ressources assignes tout
l ISA.
Contrleur dInitialisation duconducteur dur.Ceci initialise la commande et lecontrleur dIDE.
Contrleur Initialisation FloppyDrive.Ceci initialise le Floppy Drive et lecontrleur .
Tentative dinitialisation.Place la pile Basse et linitialisevia19h INTERNE.
Initialisation du Logicieldexploitation
Allumez le systme.Le D-LED sallumera si leprocesseur est endommag ouinstall de faon incorrecte.
Contrleur dInitialisation duClavier.
Essai VGA BIOS Ceci commence crire lemessage sign-on de VGA lcran.
Processeur d Initialisation.Ceci nous informe sur leprocesseur (comme le nom de lamarque, bus de systme, etc...)
TEssai RTC (Horloge en tempsrel)
Description
Rouge Vert
LED Signal
1 2
3 4
1 2
3 4
1 2
3 4
1 2
3 4
1 2
3 4
1 2
3 4
1 2
3 4
1 2
3 4
DescriptionLED Signal
1 2
3 4
1 2
3 4
1 2
3 4
1 2
3 4
1 2
3 4
1 2
3 4
1 2
3 4
1 2
3 4
Chipset en phase dinitialisation.
Essai de Dtection De Mmoire.Essai de la capacit de la mmoireintgre. Le D-LED sallumera si lemodule de mmoire estendommag ou non installcorrectement.
Dcompression de limage du BIOS la RAM pour initialiserrapidement.
IInterface Visuelle dInitialisation.Ceci dtecte lhorloge du CPU, lavrification du type de vido intgre.Puis, dtectez et initialisezladapteur visuel.
Connecteur D-Bracket 2Le connecteur est utilis pour connecter le D-Bracket 2. Le D-Bracket est pourvu de 4LED et ports USB et permet didentifier les problmes et ce laide de 16 combinaisonsde signaux LED.
19
D-Bracket 2(Optionnel)
Connecter surJDB1
Connecter surconnecteur USB
-
Fr-15
Fran
ais
Cavalier vacuer CMOSOn observe une RAM de CMOS qui comporte une alimentation dnergie de la batterieexterne pour garder les donnes de la configuration du systme. Avec la RAM deCMOS, le systme peut automatiquement initialiser lOS et il est allum chaquefois. Si vous voulez vacuer la configuration du systme, placez le JCMOS1 (ClearCMOS Jumper) pour vider la mmoire .
Attachement dAlimentation dnergie:Avant dinsrer le connecteur dalimentation dnergie, assurez-vous toujours que tousles composants sont installs correctement afin de ne pas causer de dommage. Tousles connecteurs de puissance sur la carte mre doivent se relier lalimentation dnergiedATX et doivent travailler ensemble pour une opration stable.
Connecteur Chassis Intrusion SwitchCe connecteur est connect au cble de chassis intrusion switch. Si le chassis est ouvert,le switch en informera le systme, qui enregistrera ce statut et affichera un crandalerte. Pour effacer ce message dalerte, vous devez entrer dans le BIOS et dsactiverl alerte.Vous pouvez utiliser lalimentation dnergie 20-pin ATX comme vous voulez. Si vousne voulez pas lutiliser, veuillez brancher votre alimentation dnergie au pin1 & pin13.
20
Evacuer donneG a rd e r d o n ne s(dfaut)
Important
Vous pouvez vacuer le CMOS en plaant le cavalier sur les broches 2-3, lorsquele systme est teint. Replacez ensuite le cavalier sur 1-2. Neffacez jamais leCMOS lorsque le systme est allum,cela endommagerait la carte mre.
21
1
12 24
13+3.3V+3.3VGND+5V
GND+5V
GNDPWR OK
5VSB+12V+12V
+3.3V GND+5V+5V+5VNCGNDGNDGNDPS-ON#GND-12V+3.3V
1
3
1
3
1
-
Fr-16
La Carte mre MS-7369
Connecteur Alimentation ATX 12V (2x2-Pin)Ces connecteurs de puissance 12V sont utiliss pour fournir de la puissance au CPU.
Connecteur Alimentation ATX 12V(2x4-Pin)Le connecteur dalimentation 12V est utilis pour alimenter le CPU.
Connecteur Alimentation ATX 12V (1x4-Pin)Ce connecteur de puissance 12V est utilis pour fournir de lnergie la carte mre.
8 4
15GNDGNDGNDGND
+12V+12V+12V+12V
4
21
3
5VGNDGND12V
Connecteur Alimentation ATX 20-PinCe connecteur vous permet de relier lalimentation offerte ATX 20-pin .Pour reliercette alimentation, assurez-vous que la prise dalimentation dnergie est insre danslorifice appropri et que les pins sont aligns. Abaissez alors lalimentation dnergie.
1
10 20
113.3V3.3V
GND5V
GND5V
GNDPWR OK
5VSB12V 5V
5V-5VGNDGNDGNDPS-ONGND-12V3.3V
22
23
24
25
13
4 2
GND12V12V GND
-
Fr-17
Fran
ais
Slot PCI Express (x16/ x4/ x1)Le slot PCI Express supporte la carte d'extension de l'interface PCI Express.Le slot PCI Express x 16 supporte un taux de transfert jusqu'a 4.0 GB/s.Le slot PCI Express x 8 supporte un taux de transfert jusqu'a 2.0 GB/s.Le slot PCI Express x 4 supporte un taux de transfert ju