7.0 Texan Playcenter Install Manual...2016/03/07 · swing set should be located a safe distance...

Tools Needed for AssemblyTape Measure 24” Level Angle SquarePhillips Screw Driver 3/8” Cordless Drill or Electric Drill 3/8” Drive Ratchet or Electric Impact Gun Claw Hammeror Rubber Mallet Pliers or Vise Grips 7/16” Deep Well Socket 9/16” Deep Well Socket 3/4” Deep Well Socket 1/8”, 1/4”, and 9/16” Drill Bits Phillips Head Screw Bits An Adult with two Adult Helpers

Please familiarize yourself with the install manual, parts/components and general construction process of your new swing set before getting started. Approximate assembly time: 6 to 8 hours. 6 foot unobstructed safety perimeter around swing set recommended.

7.0 Texan Playcenter Install Manual

Version 3.14

Houston, tX 77041 • www.treefrogsswingsets.com • © 2013 kiD structures inc.

When choosing a location for your swing set, always keep your child or children’s safety in mind. Here are some recommendations to help you locate and install a safe play area.● This play set is designed for the use of 4 occupants who have a combined weight not exceeding 800 pounds on the elevated floor; 3 occupants who have a combined weight of 525 pounds on the swing area; for a total unit capacity of 5 occupants who have a combined weight of 1325. (this weight is not including the picnic table area)● on-site adult supervision is required.● The swing set should be located on level ground. The stationary components such as ladders and slides are required to be a minimum of six feet from any structure or obstruction such as a fence, garage, house, tree, overhanging branches, electrical wires, clotheslines, etc. Any swinging equipment is also required to be a minimum distance twice the height of the swing beam away from these obstructions or structures as well. The swing set should be located a safe distance from any water hazards, such as a lake, river, bayou, swimming pool, etc.● Do not install this residential swing set in a commercial setting. this swing set is not manufactured for commercial usage and will void all warranties. tree frogs wooden swing set factory is not responsible for any damages or injuries resulting from this swing set being used in a commercial setting.

● never install this swing set indoors; or over concrete, asphalt, packed earth, grass, carpet or any other hard surface. A fall onto a hard surface can result in serious or fatal injury.

● the u.s. consumer Product safety commission (cPsc) recommends that you install and maintain a resilient surface under your swing set. The CPSC’s Consumer Information Sheet for Playground Surfacing Materials is on the next page. A resilient surface, should be installed after the swing set has been completely assembled according to these instructions. The swing set must rest on solid ground. Please note that this swing set has a maximum fall height of 7’.

Here are some maintenance tips required to insure safe play on your swing set for years of fun.● At the beginning of each usage season and every two weeks during, check: nuts and bolts and tighten as needed, swing seats, chains, ladders, slides, rope and wood components for sign of deterioration and replace if necessary.● On a yearly basis, we recommend that you coat your swing set with a sealant or preservative. You may also want to spot sand any areas prior to sealing.** Special note: Although we recommend that you reseal your swing set annually, you may have to touch up the high traffic areas and/or areas that have a high exposure to direct sunlight.**● Be sure that the sealant you select is non-toxic and child safe. Your local tree frogs wooden swing set factory dealer may offer a complete power wash and reseal and maintenance program.● Do not use line trimmers or “weed eaters” around your swing set. The line will remove both paint and wood from uprights and base pieces. Any damage resulting from this type of abuse is not covered under our limited warranty.● remove plastic swing seats and take in doors or do not use when temperature drops below 0°f.

Please keep this install manual for future reference.

Weight Limits for Tree Frogs Swing Sets fort Platform: 800 Lbs. total weight swing Belts: 175 Lbs. trapeze: 125 Lbs. full Bucket swing: 50 Lbs. toddler Bucket swing: 50 Lbs. tire swing: 125 Lbs. total weight rope Ladder: 75 Lbs. rock wall: 150 Lbs. All slides: 125 Lbs. tree frogs recommends that the weight limits for all components must not be exceeded. failure to adhere to these and other safety guidelines could result in damage to the swing set and/or injury to the users.

to insure sAfe PLAY adults must teach children:● not to walk close to, in front of, behind, or between moving items.● not to swing empty swing seats.● not to swing sideways into the path of adjacent swings.● not to use the swing set in a manner other than that for which it is intended.● not to get off the equipment while it is in motion.● not to jump off the tower.● not to stand in the swing seats.● not to swing so high that chains become slack, or above the height of the swing support.● not to jump on a slide.● not to climb on top of the swing support.● not to attach to the swing set any item that is not specifically designed for use with the equipment, such as (but not limited to) jump ropes, clotheslines, pet leashes, cables, and chains. these may become strangulation hazards.● to hold on to swings and climbers with both hands.● to slide feet first, never head first.● to watch for other children while swinging or playing near the swing set.

to also insure sAfe PLAY adults must:

● Limit climbing and swinging heights to each child’s ability.● Verify that suspended climbing ropes are secured at both ends.● Verify that suspended climbing ropes cannot be looped back on themselves.● Dress children appropriately for play. use well-fitted shoes that do not have slippery soles.● Avoid ponchos, scarves, hoods, loose fitting clothing, neckties, and any clothing with a drawstring. Serious injury could result should any part of the children’s clothing become entangled in the swing set.● Do not allow children to play wearing helmets.● Remember that children are inventive. When they develop games that are unsafe, be alert and change the rules.

imPortAnt - PLeAse reADAs fresh lumber acclimates to its new environment, the natural tendencies of the tree can show itself in the form of

checks, or “cracks” in the lumber. In almost all cases this is normal and it will not affect the structural integrity of your play set.Cosmetic defects that do not affect the structural integrity of the product, or natural defects of wood such as warping, checking or any other physical properties of wood that do not present a safety hazard, are not covered by this warranty.Defects that develop because the product is exposed to extreme climate conditions are not covered by this warranty.Defects that develop as a result of faulty or improper installation of the product are also not covered by this warranty.Most cracks are not warrantable, however if you believe that the integrity of your play set is compromised by this natural occurrence, please contact the tree frogs swing set Dealer that you purchased your swing set from.We appreciate your purchase and know that you will enjoy your play system for many years to come.

● Depending on your experience, assembly of our play sets can take as little as 6 hours up to 24 hours, depending on size, after inventory of parts; therefore, we recommend you set aside a full two days for assembly.● identify all of the parts for your play set. empty each box and lay out boards so you can see each part. Your instruction book will have detailed drawings that will make it easy for you to recognize individual parts. keep all hardware and metal parts separate from wooden pieces.● After everything is laid out, check carefully to ensure all parts are present. make sure there are no broken boards.● find an area to sort your hardware. it is best to open the hardware on a solid surface so that you do not lose any pieces in the grass. This will save time and familiarize you with all the different pieces in the hardware bag.**Important note: Wood has some natural defects such as knots, surface cracks, etc... We reject parts that are structurally defective. We use a high quality lumber in our structures; however, you should inspect each part for splinters or rough spots and sand them smooth to prevent injury.**● After familiarizing yourself with all of the components, read all instructions thoroughly. reading instructions after you have studied the parts will help you understand more clearly the installation process, and help to eliminate unnecessary mistakes.● Pay close attention to the diameter and length of each bolt and screw.● never tighten hardware completely at first. it helps to have some adjustment for bolt alignment while you are attaching parts together. After everything is square, tighten each joint.● After the main unit is assembled it is critical that the floor is level and square. if the main frame is not level, the walls and floor will be out of square.● After you complete installation, make sure every bolt, screw, and nut is tight, and every board is secure. wood will expand and contract with the seasons.● Place the set on level ground, not less than 6ft from any structure or obstruction such as a fence, garage, house, overhanging branches, laundry lines, or electrical wires.● All 1/4” and 3/8” lag bolts must have pre-drilled holes 1-1/2” to 2” deep. use a 1/8” drill bit for the 1/4” lag bolts and 1/4” drill bit for 3/8” lag bolts. use pre-drilled holes in facias as a reference for placing lag bolt pilot holes.● if a board lifts or rises causing a gap between boards when running in lag bolts or screws, back out the screw or lag bolt and press or apply pressure (but not enough to crack or break board) while re¬running in the lag bolt or screw in the same hole.● Do not over tighten bolts, lag bolts or screws. You can damage boards, break hardware, and/or strip out the hardware.● when using hammer do not beat on the hardware, but gently tap it in. never beat on the wood as it will leave marks.

● complete the steps which will be the basic frame of the fort {i.e. four corner posts with base (sand box boards) and deck supports}● Position in the most level area chosen for the play set, keeping in mind the location and size of the swing beam, ladder, slides, etc. that extend off the fort.● once the frame is in the final position, check for vertical and horizontal levelness to determine which side(s) will need to be dug into the ground to level the play set.● with a shovel, score the ground around the outside edges of the sandbox boards on the ‘high’ side of the fort. this is the area that will be dug in. make sure to score deep enough; the scored lines will be your digging template.● Push the frame off and away from the scored area, far enough to dig and remove dirt to reach the appropriate depth.● Dig a channel along the scored line(s) for the base of the fort (corner post and sandbox boards) to rest into. Dig the channel(s) to the same level depth. the bottom of the channel(s) should be level to each other so your frame doesn’t teeter or rock because the channel(s) are uneven.● once you have removed enough grass and dirt, slide/push the frame into the channel(s). Place a level on the vertical and horizontal boards of the frame to determine if enough soil, or too much, was removed.● repeat this process until the basic frame is plumb and level and in its final position before completing the rest of the assembly.● measure to make sure fort is square.

** Important: if you require a channel depth of more than 6”,then we recommend you have your play set area professionally graded before completing assembly. **

consumer informAtion sHeet for PLAYgrounD surfAcing mAteriALs

the u.s. consumer Product safety commission (cPsc) estimates that about 100,000 playground equipment related injuries resulting from falls to the ground surface are treated annually in U.S. hospital emergency rooms.Injuries involving this hazard pattern tend to be among the most serious of all playground injuries, and have the potential to be fatal, particularly when the injury is to the head. The surface under and around playground equipment can be a major factor in determining the injury-causing potential of a fall. it is self-evident that a fall onto a shock-absorbing surface is less likely to cause a serious injury than a fall onto a hard surface. However, it should be recognized that some injuries from falls will occur no matter what playground surfacing material is used.

Playground equipment should never be placed on hard surfaces such as concrete or asphalt. Grass may appear to be acceptable, but can turn to hard packed earth in areas of high traffic. shredded bark mulch, wood chips, or fine gravel are considered to be acceptable shock absorbing surfaces when installed and maintained at a sufficient depth under and around play equipment.

tABLe 1 -criticAL HeigHts (in feet) of testeD mAteriAL

MATERIAL UNCOMPRESSED DEPTH COMPRESSED DEPTH 6 Inch 9 Inch 12 Inch 9 inchWood Chips 7 10 11 10Double Shredded Bark Mulch 6 10 11 7engineered wood fibers 6 7 >12 6fine sand 5 5 9 5coarse sand 5 5 6 4fine gravel 6 7 10 6medium gravel 5 5 6 5shredded tires** 10-12 n/A n/A n/A

** This is data from tests conducted by independent testing laboratories on a 6 inch depth of uncompressed shredded tire samples produced by four manufacturers. The test reported critical heights, which varied from 10 feet to greater than 12 feet. It is recommended that persons seeking to install shredded tires as a protective surface request test data from the supplier showing the critical height of the material when it was tested in accordance with Astm f1292.

Table 1 should be read as follows: If, for example, uncompressed wood chips are used at a minimum of 6 inches, the Critical Height is 7 feet. If 9 inches of uncompressed wood chips are used, the Critical Height is 10 feet. It should be noted that, for some materials, the Critical Height decreases when the material is compressed. It is recommended that a shock absorbing material should extend a minimum of 6 feet in all directions from the perimeter of stationary equipment such as climbers and slides. However, because children may deliberately jump from a moving swing, the shock absorbing material should extend in the front and rear of a swing a minimum distance of 2 times the height of the pivot point measured from a point directly beneath the pivot on the supporting structure.this information is intended to assist in comparing the relative shock-absorbing properties of various materials. no particular material is recommended over another. However, each material is only effective when properly maintained. Materials should be checked periodically and replenished to maintain correct depth as determined necessary for your equipment. The choice of a material depends on the type and height of the playground equipment, the availability in your area, and its cost.

this information has been extracted from the cPsc publications “Playground surfacing-technical information guide” and “Handbook for Public Playground Safety.” Copies of these reports can be obtained by sending a postcard to:

office of Public AffairsU.S. Consumer Product Safety Commission

Washington, D.C. 20207toll-free Hotline: 1-800-638-2772 or at http://www.cpsc.gov

Playcenter Universal Bundle 1 &2Item No.

uB-1uB-2uB-3uB-4uB-5uB-6uB-7uB-8uB-9uB-10uB-11uB-12

Part Number17-4-0018616-4-0021316-4-0021616-4-0021717-4-0010617-4-0010716-4-0021512-4-0014116-4-0021816-4-0021416-4-0022316-4-00224

Part DescriptionUNIVERSAL PLAYCENTER MAINBEAMUNI. PLAYCENTER CENTER POST(L) gusset BrAcket(r) gusset BrAcket(L) PLAYcenter suPPort gusset(r) PLAYcenter suPPort gussetuniVersAL roPe BLockUNIVERSAL RAIL BOTTOMuniVersAL entrAPment BLockUNI. PLAYCENTER CORNER POSTUNI. PC. TOP jOIST W/ SWING HOLESUNI. PC. TOP jOIST

QTY.225522131411

Texan PLaycenTer BUndLetX-1tX-2tX-3tX-4tX-5tX-6

16-4-0022012-4-0014612-4-0014516-4-0022116-4-0021916-4-00222

TExAN PLAYCENTER UPPER ROPE ARMTExAN PLAYCENTER TARP BOARDUNIVERSAL TARP BOARDTExAN PLAYCENTEER GROUND RUNNERTExAN PLAYCENTER LOWER ROPE RUNNERTExAN PLAYCENTER UPPER ACCESSORY ARM

121111

7.0 Texan PLaycenTer BUndLe c.7tX-17tX-27tX-37tX-47tX-57tX-67tX-77tX-87tX-97tX-10

17-4-0016917-4-0017017-4-0017120-4-0000117-4-0017217-4-0017311-4-0010311-4-0010211-4-0010164-6-00003

(L) PLAYcenter wooD steP LADDer LegCENTER WOOD STEP/ CHAIN LADDER LEG(r) PLAYcenter cHAin LADDer Leg7 1/4” WOOD STEP(r) Pc rockwALL LADDer Leg(L) Pc rockwALL LADDer LegtX Pc rockwALL BoArD w/ out HoLestX Pc rockwALL BoArD w/ HoLestX Pc rockwALL BoArD w/ roPe HoLeroPe run-ceDAr

11181171018

Texan PLaycenTer Wood rooF BUndLeItem No.

wr-1wr-2wr-3wr-4wr-5wr-6wr-7wr-8wr-9wr-10wr-11wr-12wr-13wr-14wr-15wr-16

Part Number10-4-0034812-4-0020412-4-0020519-4-0009219-4-0009312-4-0020812-4-0020910-4-0034610-4-0034720-4-0000510-4-0020910-4-0021210-4-0021010-4-0021310-4-0021410-4-00211

Part DescriptiontX Pc wooD roof tArP BoArDuni. Pc (L) wooD roof suPPortuni. Pc (r) wooD roof suPPorttX Pc wooD roof BoArDtX Pc wooD roof BoArD riPPeDqc Pc wooD roof runnerqc Pc wooD roof runner #2qc Pc wooD roof center suPPortqc Pc wooD roof center suPPort #2uniVersAL center fAn BoArDuniVersAL Pc Bottom fAn BoArDuniVersAL Pc center fAn BoArDuni. Pc. Long (L) siDe fAn BoArDuni. Pc. Long (r) siDe fAn BoArDuni. Pc. sHort (r) siDe fAn BoArDuni. Pc. sHort (L) siDe fAn BoArD

QTY.12232244222222222

UniverSaL raiL(coUnT iS For a SingLe raiL)

rA-1rA-2rA-3

UNIVERSAL RAIL TOPUNIVERSAL RAIL BOTTOMUNIVERSAL SPINDLE

115

UniverSaL deck

7.0 Texan Pc Box a. or B.(coLor dePendS on Box)

7Pc-17Pc-27Pc-37Pc-47Pc-57Pc-67Pc-77Pc-87Pc-97Pc-107Pc-11

36-1-0002336-1-0002465-7-0001865-7-0002037-1-0001937-1-0001851-1-0003351-1-0003456-1-0001560-1-0000654-2-00002

LArge rock (muLti- coLor)LArge rock (green)18’ YELLOW ROPE19’ YELLOW ROPE19” sHiPs wHeeL (green)19” sHiPs wHeeL (YeLLow)66” PLAstisoL coAteD cHAin (YeLLow)66” PLAstisoL coAteD cHAin (green)tire swiVeL(Brown)20” trAPeze BAr w/ rings (YeLLow)1 1/4” X 25” PLAYgriP tuBe Pc coAteD

2020131133112

Deck-1Deck-2Deck-3Deck-4

12-4-0013813-4-0006312-4-0013913-4-00064

Deck runnerDeck suPPortsmALL Deck BoArDLArge Deck BoArD

4286

TarP BagS (coLor dePendS on Box)

Item No.tB-1tB-2tB-3

Part Number61-8-0005561-8-0005661-8-00054

Part DescriptiontX Pc tArP BAg (BYB)tX Pc tArP BAg (rYr)tX Pc tArP BAg (green)

QTY.111

TireTIRE 34-1-00003 TIRE SWING TIRE 1

Tx PLaycenTer- STandard Box hardWarest-1st-2st-3st-4st-5st-6st-7st-8st-9st-10st-11st-12st-13st-14st-15st-16st-17st-18st-19st-20

40-1-0008440-1-0008340-1-0008240-1-0008140-1-0007440-1-0007340-1-0002840-1-0006440-1-0001340-1-0001240-1-0004340-1-0006140-1-0005940-1-0005640-1-0005540-1-0006940-1-0007041-1-0002540-1-0000140-1-00002

3/4” uss fLAtwAsHer1/2” uss fLAtwAsHer3/8” uss fLAtwAsHer1/4” uss fLAtwAsHer1/2” sPLit LockwAsHer3/8” sPLit LockwAsHer1/2” HEx NUT3/8” nYLon insert Locknut1/2” x 7” CARRIAGE BOLT1/2” x 4 1/2” CARRIAGE BOLT3/8” X 5” HeX BoLt3/8” X 5” LAg BoLt3/8” x 3 1/2” LAG BOLT1/4” x 4 1/2” LAG BOLT1/4” x 3” LAG BOLT#14 X 1 1/4” PAn PHiLLiPs ts#14 X 2” PAn PHiLLiPs ts3/8” BOLT CUP3/8” ACORN NUT1/2” ACORN NUT

222251472242242024113620122154422

Tx PLaycenTer STandard Boxtst-1tst-2tst-3tst-4tst-5tst-6tst-7tst-8tst-9tst-10

53-1-0001254-2-0000454-2-0000257-2-0000457-2-0000556-1-0001259-1-0001159-1-0001337-1-0002159-1-00008

21” X 63” cHAin LADDer- (YeLLow)1 1/4” x 44” PLAYGRIP TUBE PC COATED1 1/4” X 25” PLAYgriP tuBe Pc coAteD1 1/4” PLAYgriP sAfetY HAnDLes1 1/4” PLAYGRIP LADDER HANDLESDUCTILE IRON SWING HANGERSSPRING CLIPS 10MM x 100MMtree frogs PLAqueTELESCOPETIRE SWING EYE BOLT

1114225113

7.0 Tx PLaycenTer- hardWare Bag7Pc-127Pc-137Pc-147Pc-157Pc-167Pc-17

40-1-0002240-1-0005640-1-0006740-1-0007740-1-0008140-1-00111

2 1/2” coAteD Deck screws1/4” x 4 1/2” LAG BOLT1/4” x 1 1/2” PAN PHILLIPS M/S1/4” X 7/16 4 Prong t-nut1/4” uss fLAtwAsHer2” METAL TAP SCREW

72324040728

Texan PLaycenTer Wood rooF hardWareItem No.

wr-17wr-18wr-19wr-20wr-21wr-22wr-23wr-24wr-25wr-25wr-26

Part Number40-1-0008340-1-0008240-1-0008140-1-0007340-1-0002640-1-0000140-1-0011540-1-0005640-1-0005540-1-0005440-1-00020

Part Description1/2” uss fLAtwAsHer3/8” uss fLAtwAsHer1/4” uss fLAtwAsHer3/8” sPLit LockwAsHer3/8” HEx NUT3/8” ACORN NUT3/8” X 5” cArriAge BoLt1/4” x 4 1/2” LAG SCREW1/4” x 3” LAG SCREW1/4” x 2” LAG SCREW1 5/8” coAteD Deck screws

QTY.4438444424214210

UniverSaL raiL hardWare(coUnT For one raiL)

rA-4 40-1-00022 2 1/2” coAteD Deck screws 20

Playcenter Universal BUndle 1 & 2#UB1

17-4-00186Universal Pc Main Beam 107”

Qty. 2

#UB216-4-00213

Uni. Pc center Post 88”Qty. 2

#UB316-4-00216

(l) Gusset Bracket 19”Qty. 5

#UB416-4-00217

(r) Gusset Bracket 19”Qty. 5

#UB517-4-00106

(l) Pc support Gusset 16”Qty. 2

#UB617-4-00107

(r) Pc support Gusset 16”Qty. 2

#UB716-4-00215

Universal rope Block 11”Qty. 1

#UB812-4-00141

Universal rail Bottom 25”Qty. 3

#UB916-4-00218

Universal ent. Block 25”Qty. 1

#UB1016-4-00214

Uni. Pc. corner Post 39”Qty. 4

#UB1116-4-00223

Uni. Pc. top Joist w swing Holes 125”Qty. 1

#UB1216-4-00224

Uni. Pc. top Joist 125”Qty. 1

Playcenter Universal BUndle 1 & 2#tX-1

16-4-00220tX Pc Upper rope arm 105 1/2”

Qty. 1

#tX-212-4-00146

tX Pc tarp Board 68”Qty. 2

#tX-312-4-00145

Universal tarp Board 61”Qty. 1

#tX-416-4-00221

tX Pc Ground runner 71”Qty. 1

#tX-516-4-00219

tX Pc lower rope runner 107”Qty. 1

#tX-616-4-00222

tX Pc Upper acc. arm 105 1/2”Qty. 1

7.0 teXan Pc BUndle c.#7tX-1

17-4-00169(l) Pc Wood step ladder leg 99”

Qty. 1

#7tX-217-4-00170

center Wood step/ chain ladder leg 99”Qty. 1

#7tX-317-4-00171

(r) Pc chain ladder leg 99”Qty. 1

7.0 teXan Pc BUndle c. cont.#7tX-4

13-4-00066Wood step 18 1/2”

Qty. 8

#7tX-517-4-00172

(r) Pc rockwall ladder leg 99”Qty. 1

#7tX-617-4-00173

(l) Pc rockwall ladder leg 99”Qty. 1

#7tX-711-4-00103

tX Pc rW Board W/ out Holes 43 1/2”Qty. 4

#7tX-811-4-00102

tX Pc rW Board W/ Holes 43 1/2”Qty. 8

#7tX-911-4-00101

tX Pc rW Board W/ rope Hole 43 1/2”Qty. 1

teXan Pc Wood rooF BUndle #Wr-1

10-4-00348tX Pc Wood roof tarp Board”

Qty. 1

#Wr-212-4-00204

Uni. Pc (l) Wood roof support 79”Qty. 2

#Wr-312-4-00205

Uni. Pc (r) Wood roof support 79”Qty. 2

teXan Pc Wood rooF BUndle cont.#Wr-4

19-4-00092tX Pc Wood roof Board 68”

Qty. 32

#Wr-519-4-00093

tX Pc Wr Board ripped 68”Qty. 2

#Wr-612-4-00208

Qc Pc Wood roof runner 36”Qty. 4

#Wr-712-4-00209

Qc Pc Wood roof runner 39 1/2”Qty. 4

#Wr-810-4-00346

Qc Pc Wood roof center support 36”Qty. 2

#Wr-910-4-00347

Qc Pc Wood roof center support 39 1/2”Qty. 2

#Wr-1020-4-00005

Universal center Fan Board 15 1/4”Qty. 2

#Wr-1110-4-00209

Uni. Pc Bottom Fan Board 62”Qty. 2

#Wr-1210-4-00212

Uni. Pc center Fan Board 20 1/4”Qty. 2

#Wr-1310-4-00210

Uni. Pc long (l) side Fan Board 19”Qty. 2

#Wr-1410-4-00213

Uni. Pc long (r) side Fan Board 19”Qty. 2

#Wr-1510-4-00214

Uni. Pc short (r) side Fan Board 14”Qty. 2

#Wr-1510-4-00211

Uni. Pc short (l) side Fan Board 14”Qty. 2

rail BUndlera-1

12-4-00140Universal rail top

Qty. 3

ra-212-4-00141

Universal rail BottomQty. 3

ra-315-4-00008

Universal rail PicketQty. 15

decK BUndledecK-1

12-4-00138deck runner

Qty. 4

decK-213-4-00063

deck supportQty. 2

decK-312-4-00139

small deck BoardQty. 8

decK-413-4-00064

large deck BoardQty. 6

7.0 Texan Box A. & B.

#7PC-637-1-00018

19” Ship’s Wheel- YellowQTY. 1

#7PC-537-1-00019

19” Ship’s Wheel- GreenQTY. 1

#7PC-136-1-00023

Large Rock (Multi Color)QTY. 20

#7PC-236-1-00024

Large Rock (Green)QTY. 20

#7PC-365-7-00018

18’ Yellow RopeQTY. 1

#7PC-465-7-00020

19’ Yellow RopeQTY. 3

#7PC-751-1-00033

66” Plastisol Coated Chain (Yellow)QTY. 3

#7PC-851-1-00034

66” Plastisol Coated Chain (Green)QTY. 3

#7PC-956-1-00015Tire Swivel

QTY. 1

#7PC-1060-1-00006

20” Trapeze w/ 43” Chain- YellowQTY. 1

#7PC-1154-2-00005

1 1/4” x 25” Tube PC CoatedQTY. 2

Tarp (Color Varies With Order)#TB-1

61-8-00055TX PC Tarp Bag- BYB

QTY. 1

#TB-261-8-00056

TX PC Tarp Bag-RYRQTY. 1

#TB-361-8-00054

TX PC Tarp Bag- GreenQTY. 1

Texan PC Standard Box#TST-1

53-1-0001221 x 63” Chain Ladder- (Yellow)

QTY. 1

#TST-254-2-00004


#TST-354-2-00005


#TST-457-2-00004

1 1/4” Playgrip Safety HandlesQTY. 4

#TST-554-2-00004

1 1/4” Playgrip Ladder HandlesQTY. 2

#TST-656-1-00012

Ductile Iron hangersQTY. 2

#TST-759-1-00011

Spring Clips 10 x 100mm QTY. 2

#TST-859-1-00013

Tree Frogs PlaqueQTY. 1

#TST-937-1-00021Telescope

QTY. 1

#TST-1059-1-00008

Tire Swing Eye BoltQTY. 1

Texan STandard Hdwr.InSTaLLer nOTe: (YOU MUST aSSeMBLe THIS PrOdUCT In aCCOrdanCe wITH THeSe aSSeMBLY InSTrUCTIOnS. wHen COMPLeTe

GIVe ManUaL TO Owner.)

MeasureMent taken froM bottoM of bolt head to the bottoM of bolt

USE THE RULER TO MEASURE YOUR BOLTS AND SCREWS. HARDWARE VIEWS SHOWN ABOVE ARE 1:1 SCALE AND CAN BE USED TO MATCH HARDWARE SIZES.

#st-140-1-00084

3/4” uss flatwasherQtY. 22

#st-240-1-00083


#st-340-1-00082


#st-440-1-00081


#st-540-1-00074

1/2” split lockwasherQtY. 22

#st-640-1-00073


#st-740-1-00028

1/2” hex nutQtY. 22

#st-840-1-00064

3/8” nylon locknutQtY. 4

#st-940-1-00013

1/2” x 7” Carriage boltQtY. 20

#st-1940-1-00001

3/8” acorn nutQtY. 4

#st-2040-1-00002

1/2”acorn nutQtY. 22




#st-1040-1-00012

1/2” x 4 1/2” Carriage boltQtY. 2

#st-1140-1-00043

3/8” x 5” hex boltQtY. 4

#st-1240-1-00061

3/8” x 5” lag boltQtY. 11

#st-1340-1-00059

3/8” x 3 1/2” lag boltQtY. 36

#st-1440-1-00056

1/4” x 4 1/2” lag boltQtY. 20

#st-1540-1-00055





7.0 tX PC hardware bag

#st-1640-1-00069

#14 x 1 1/4” Pan Phillips tsQtY. 2

#st-1740-1-00070

#14 x 2” Pan PhillipsQtY. 15

#st-1841-1-00025

3/8” bolt CupQtY. 4

#7PC-1140-1-00022

2 1/2” Coated deck screwQtY. 72

#7PC-1240-1-00056

1/4” x 4 1/2” lag boltQtY. 32

#7PC-1340-1-00067

1/4” x 1 1/2” Pan PhillipsQtY. 40

#7PC-1440-1-00077

1/4” x7/16 4 Prong t-nutQtY. 40

#7PC-1540-1-00081


#7PC-1640-1-00111

2” Metal tap screwQtY. 8

Texan wOOd rOOF Hdwr.InSTaLLer nOTe: (YOU MUST aSSeMBLe THIS PrOdUCT In aCCOrdanCe wITH THeSe aSSeMBLY InSTrUCTIOnS. wHen COMPLeTe



#wr-1740-1-00083


#wr-1840-1-00082


#wr-1940-1-00081


#wr-2040-1-00073


#wr-2140-1-00026

3/8” hex nutQtY. 4

#wr-2240-1-00001

3/8” acorn nutQtY. 4

#wr-2340-1-00115

3/8” x 5” Carriage boltQtY. 4

#wr-2440-1-00056

1/4” x 4 1/2” lag bolt QtY. 24#wr-25

40-1-000551/4” x 3” lag bolt

QtY. 2

#wr-2640-1-00054


#wr-2740-1-00020

1 5/8” Coated deck screwQtY. 210

rail hardware#ra-4

40-1-00022 2 1/2” Coated deck screw

QtY. 20

Ladder/ Chain Ladder AssemblyPARTS

#7TX- 1- (L) Playcenter Wood Step Ladder Leg- (1)#7TX- 2- Center Wood Step/ Chain Ladder Leg- (1)#7TX- 3- (R) Playcenter Chain Ladder Leg- (1)#7TX- 4- 5 1/4” Wood Step- (6)

HARdwARe#7PC- 13- 1/4” X 4 1/2” Lag Bolt- (28) #7PC- 16- 1/4” USS Flatwasher- (28)#7PC- 17- 2” Metal Tap Screw- (8) #7PC-11- 1 1/4” x 25” Tube- (2)#TST- 2 - 1 1/4” x 44” Playgrip Tube PC Coated- (1)#TST- 3 - 1 1/4” x 25” Playgrip Tube PC Coated- (1)#TST- 1 - 21 x 63” Chain Ladder- (1)

6PC-16

6PC-13

6PC-17

7TX-3

TST-1 TST-3

7PC-11

TST-2

7TX-2

7TX-47TX-1

7PC-11

Metal Tap screw the end of each Tube

Ladder/ Chain Ladder AssemblyPARTS

#TX-4 - Texan Playcenter Ground Runner- (1)#UB-3 - (L) Gusset Bracket- (1)#UB-4 - (R) Gusset Bracket- (1)

HARdwARe#ST- 12 - 3/8” X 5” Lag Bolt- (3)#ST- 3 - 3/8” USS Flatwasher- (7)#ST- 13 - 3/8” x 3 1/2” Lag Bolt- (4)

ST-12

ST-3

ST-13

ST-3

TX-4 UB-4 UB-3

Rockwall AssemblyPARTS

#7TX-5- (R) Rockwall Ladder Leg (1)#7TX-6- (L) Rockwall Ladder Leg (1)#7TX-7- TX PC Rockwall Board W/ Out Holes- (7)#7TX-8- TX PC Rockwall Board W/ Holes- (10)#7TX-9- TX PC Rockwall Board W/ Rope Hole- (1)

HARdwARe#7PC-12- 2 1/2” Coated Deck Screws (56)#7PC-14- 1/4” x 1 1/2” Pan Phillips M/S- (32)#7PC-16- 1/4” USS Flatwasher- (32)#7PC-15- 1/4” x 7/16” 4 Prong T-Nut (32)#7PC-1 or 2- Large Rock- (16)

7PC-15

7TX-87PC-14

7PC-16 7PC-1 or 2

7TX-8

7PC-12

7TX-7

7TX-9

7TX-8

Rockwall AssemblyPARTS

#TX-5 - Texan Playcenter Lower Rope Runner- (1)#UB-3 - (L) Gusset Bracket- (1)#UB-4 - (R) Gusset Bracket- (1)

HARdwARe#ST- 12 - 3/8” X 5” Lag Bolt- (2)#ST- 3 - 3/8” USS Flatwasher- (6)#ST- 13 - 3/8” x 3 1/2” Lag Bolt- (4)

12” Space

TX-5

ST-12

ST-3

UB-3

UB-4

ST-3

ST-13

Rail Assembly

2 13/16” Gap Between Spindles

3 1/2” Gap

Main AssemblyPARTS

#RA-1- Universal Rail Top- (1)#RA-2- Universal Rail Bottom- (1)#RA-3- Universal Spindle- (5)#UB-1- Universal PC Main Beam- (2)

HARdwARe#RA-4- 2 1/2” Coated Deck Screw- (20) #ST-20- 1/2” Acorn Nut- (4)#ST-9- 1/2” X 7” Carriage Bolt- (4) #ST-1- 3/4” USS Flatwasher- (4)#ST-2- 1/2” USS Flatwasher- (4) #ST-5- 1/2” Split Lockwasher-(4)#ST-7- 1/2” Hex Nut- (4)

RA-1

RA-3

RA-2

RA-4

UB-1

ST-20ST-7

ST-5

ST-2

ST-1

ST-9

Main AssemblyPARTS

#UB-5- (L) Playcenter Support Gusset- (2)#UB-6- (R) Playcenter Support Gusset- (2)#UB-2- Uni. Playcenter Center Post- (2)#UB-10- Uni. Playcenter Corner Post- (4)

HARdwARe#ST- 9- 1/2” X 7” Carriage Bolt- (6) #ST-1- 3/4” USS Flatwasher- (6) #ST- 2- 1/2” USS Flatwasher- (6) #ST-5- 1/2” Split Lockwasher- (6)#ST- 7- 1/2” Hex Nut- (6) #ST-20- 1/2” Acorn Nut- (6)#ST- 13- 3/8” x 3 1/2” Lag Bolt- (16) #ST -3 - 3/8” USS Flatwasher- (16)

UB-5

UB-6

ST-3

ST-13

ST-9ST-1

ST-2

ST-5

ST-20

ST-7

deck AssemblyPARTS

DeCk-1- DeCk RUNNeR- (4)DeCk-2- DeCk SUPPORT- (2)DeCk-3- SMALL DeCk BOARD- (8)DeCk-4- LARGe DeCk BOARD- (6)

HARdwAReDeCk-5- 2 1/2” COATeD DeCk SCReW- (84)

3 1/2” Gap 3 1/2” Gap

24 1/4” Gap

12 1/4” Gap

DeCk-1

DeCk-1

DeCk-2

DeCk-4

DeCk-4

DeCk-3

DeCk-5DeCk-5

Main AssemblyPARTS

Deck- Universal Deck (2)HARdwARe

#ST-14- 1/4” X 4 1/2” Lag Bolt- (8)#ST- 4- 1/4” USS Flatwasher (8)

DeCk

ST-4 ST-14

Main AssemblyPARTS

#UB-3- (L) Gusset Bracket- (2)#UB-4- (R) Gusset bracket- (2)#UB-11- Uni. PC Top Joist W/ Swing Holes- (1)#UB-12- Uni. PC Top Joist- (1)

HARdwARe#ST- 9- 1/2” X 7” Carriage Bolt- (6) #ST-1- 3/4” USS Flatwasher- (6) #ST- 2- 1/2” USS Flatwasher- (6) #ST-5- 1/2” Split Lockwasher- (6)#ST- 7- 1/2” Hex Nut- (6) #ST-20- 1/2” Acorn Nut- (6)#ST- 13- 3/8” x 3 1/2” Lag Bolt- (8) #ST -3 - 3/8” USS Flatwasher- (8)

UB-12

UB-11

UB-4

UB-3

ST-20

ST-7

ST-5ST-2

ST-1

ST-9

ST-13ST-3

Main AssemblyPARTS

#TX-1- TX PC Upper Rope Arm- (1)#TX-6- TX PC Upper Accessory Arm- (1)

HARdwARe#ST- 9- 1/2” X 7” Carriage Bolt- (4) #ST-1- 3/4” USS Flatwasher- (4) #ST- 2- 1/2” USS Flatwasher- (4) #ST-5- 1/2” Split Lockwasher- (4)#ST- 7- 1/2” Hex Nut- (4) #ST-20- 1/2” Acorn Nut- (4)#ST- 12 - 3/8” x 5” Lag Bolt- (4) #ST -3 - 3/8” USS Flatwasher- (4)

TX-6

TX-1

ST-9

ST-1

ST-20

ST-7ST-5ST-2

ST-3

ST-12

Main AssemblyPARTS

#UB-3- (L) Gusset Bracket- (1)#UB-4- (R) Gusset Bracket- (1)#TST-6- Ductile Iron Swing Hangers- (2)

HARdwARe#ST- 11- 3/8” X 5” Hex Bolt- (4) #ST-3- 3/8” USS Flatwasher- (8) #ST- 18- 3/8” Bolt Cup- (4) #ST-6- 3/8” Split Lockwasher- (4)#ST- 8- 3/8” Hex Nut- (4) #ST-19- 3/8” Acorn Nut- (4)#ST- 13 - 3/8” x 3 1/2” Lag Bolt- (4)

ST-11

ST-18

ST-6

ST-19

ST-3ST-8

TST-6

ST-3

ST-13

UB-4

UB-3

Main AssemblyPARTS

#RAIL- Universal Rail- (1)#UB-8- Universal Rail Bottom- (3)

HARdwARe#ST-14- 1/4” X 4 1/2” Lag Bolt- (6) #ST-4- 1/4” USS Flatwasher- (18)#ST-15- 1/4” x 3” Lag Bolt- (12)

ST-4

ST-14

ST-14

ST-4

ST-4

ST-15

UB-8

Tarp Assembly Trapeze InstallPARTS

#TX-2- TX Playcenter Tarp Board- (2)#TX-3- Universal Tarp Board- (1)#6PC-10- 20” Trapeze Bar (Yellow)- (1)

HARdwARe#ST-14- 1/4” X 4 1/2” Lag Bolt- (6)#ST-4- 1/4” USS Flatwasher- (6)

ST-14

ST-4

TX-2

TX-3

Rope Ladder Assembly

In this step we are connecting the Rope Blockon the Texan Playcenter Upper Rope Arm andthe Texan Playcenter Lower Rope Runner.1.) Thread the Rockwall Rope through theRope Block and tie a knot.2.) Tie 4 knots spaced evenly throughout thelength of the Rockwall Rope.3.)Place the Rockwall Rope through the TexanPlaycenter Lower Rope Runner on the backside.

In this step we are connecting the Rope Ladderto the Texan Playcenter Upper Rope Arm and theTexan Playcenter Lower Rope Runner.1.)Thread the Ladder Ropes through the TexanPlaycenter Upper Rope Arm and tie knots.2.) Slide a Rope Rung up the Ladder Ropes withabout 10”-11” between bottom of the TexanPlaycenter Upper Rope Arm and Rope Rung, tiea single knot on each rope, directly below itemRope Rung.3.) Repeat step 2 for the remaining Rope Rungswith about 10”-11” between each Rope Rung.

Tarp Assembly

Figure A. Figure B.(Figure A.)- Take one corner of the VINYL TARP and place it flush in the corner.Tap the snap with a blunt object, leaving an indention of the snap in the wood. Repeat thisprocess until all the snaps have been indented in the wood on both sides of the Playcenter.

(Figure B.)- Using the indentions you just made with the snaps, take the 5/8” PHILLIPS SCReW SNAPS and drill one into each indention.

Tarp Assembly 8 Board Roof Panel

Take the corner of the VINYL TARP and start placing the snaps on the PHILLIPSSCReW SNAPS. Fold the VINYL TARP over the top of the UNIVeRSAL TARP BOARD. Pulltight and place the snaps on the PHILLIPS SCReW SNAPS.

PARTS#WR-4- TX PC Wood Roof Board- (16)#WR-6- QC PC Wood Roof Runner- (4)

HARdwARe#WR-26- 1 5/8” Coated Deck Screws- (64)

#WR-26

Repeat this step one more time for 2, 8 Board Roof Panels

5“ Gap

#WR-4 #WR-6

Place WR-6 to the inner lip of the 1st Wood Roof Board

32 1/4“ Gap

PARTS#WR-9- QC PC Wood Roof Center Support- (2)#WR-7- QC PC Wood Roof Runner #2- (4)#WR-5- TX PC Wood Roof Board Ripped- (2)#WR-4- TX PC Wood Roof Board- (16)



#WR-9

#WR-26

8 Board Roof Panel 9 Board Roof Panel


#WR-26

13/16“ Gap #WR-4

5“ Gap

#WR-5

9 Board Roof PanelPARTS

#WR-8- QC PC Wood Roof Center Support- (2)#WR10- Universal Center Fan Board- (2)#WR-11- Universal PC Bottom Fan Board- (2)


#WR-26


32 1/4“ Gap#WR-8

wood Roof Fan

Repeat this step one more time for 2, Wood Roof Fans

#WR-26

#WR-10#WR-1119 1/8” Gap

wood Roof FanPARTS

#WR-12- Universal PC Center Fan Board- (2)#WR-13- Uni. PC Long(L) Side Fan Board- (2)#WR-14- Uni. PC Long(R) Side Fan Board- (2)#WR-15- Uni. PC Short (R) Side Fan Board- (2)#WR-16- Uni. PC Short (L) Side Fan Board- (2)


#WR-26

#WR-12 #WR-14

#WR-15 #WR-16

#WR-13

#WR-26

Repeat this step one more time for 2, Wood Roof Fans

25” Gap

wood Roof AssemblyPARTS

#WR-1- TX PC Wood Roof Tarp Board- (1)#WR-2- Uni. PC (L) Wood Roof Support- (2)#WR-3- Uni. PC (R) Wood Roof Support- (2)

HARdwARe#WR-23- 3/8” x 5” Carriage Bolt- (4) #WR-25- 1/4” x 3” Lag Bolt- (2)#WR-17- 1/2” USS Flatwasher- (4) #WR-18- 3/8” USS Flatwasher- (4)#WR-20- 3/8” Split lockwasher- (4) #WR-21- 3/8” Hex Nut- (4)#WR-22- 3/8” Acorn Nut- (4) #WR-19- 1/4” USS Flatwasher- (2)

#WR-3

#WR-2

#WR-22#WR-20

#WR-21

#WR-18

#WR-23

#WR-17

#WR-1

#WR-25

#WR-19

wood Roof AssemblyPARTS

Wood Roof 8 Board Panels- (2)Wood Roof 9 Board Panels- (2)

HARdwARe#WR-24- 1/4” X 4 1/2” Lag Screw- (24)#WR-19- 1/4” USS Flatwasher- (24)

#WR-24

#WR-24

#WR-19

#WR-19

8 Board Roof Panel

9 Board Roof Panel

PARTS#UB-9- Universal ent. Block- (1)Wood Roof Fan- (2)

HARdwARe#ST-12- 3/8” X 5” Lag Bolt- (2)#ST-3- 3/8” USS Flatwasher- (2)#WR-25- 1/4” x 2” Lag Screw- (14)#WR-19- 1/4” USS Flatwasher- (14)

ST-12

ST-3

Slide Install

#WR-FAN

#WR-19

#WR-25

wood Roof Fan

Slide Install Safety Handle InstallPARTS

#TST-4- 1 1/4” Playgrip Safety Handles- (4)HARdwARe

#ST-16- #14 X 1 1/4” Pan Phillips- (11)#ST- 4- 1/4” USS Flatwasher- (3)

ST-16

ST-4 ST-16

Ladder Handle Install Ships wheel InstallPARTS

#TST-5- 1 1/4” Playgrip Ladder Handles- (2)#5PC-5 or 6- 19” Ships Wheel w/ Hardware- (1)

HARdwARe#ST-17- #14 X 1 1/4” Pan Phillips- (4)

ST-17

TST-5

Telescope Install Tire Swing InstallPARTS

#TST-9- Telscope- (4)#TST-10- Tire Swing eye Bolts- (3)

Tire Swing Assembly

Using a pencil or pen mark the holes in the center of the deck.

Drill Marked Holes from previous step using a 9/16” bit.

PARTSPencil- (1)9/16” Drill Bit- (1)

Tire Swing AssemblyPARTS

#5PC-9- Tire Swivel- (1)HARdwARe

#ST-10- 1/2” x 4 1/2” Carriage Bolt- (2) #ST-1- 3/4” USS FLatwasher- (2)#ST-2- 1/2” USS Flatwasher- (2) #ST-5- 1/2” Split Lockwasher- (2)#ST-7- 1/2” Hex Nut- (2) #ST-20- 1/2” Acorn Nut- (2)

ST-10 ST-1

5PC-9ST-2

ST-5

ST-7

ST-20

7.0 Texan Playcenter Install Manual...2016/03/07 · swing set should be located a safe distance...

Documents

Transcript of 7.0 Texan Playcenter Install Manual...2016/03/07 · swing set should be located a safe distance...