VisionPRO® TH8000 SeriesTouch-screen Programmable Thermostat

® U.S. Registered Trademark. Copyright © 2012 Honeywell International Inc.

All rights reserved.

Installation Guide

69-2693-01

System Types• Gas,oil,orelectricheatwithair

conditioning

• Warmair,hotwater,highefficiencyfurnaces,heatpumps,steam,gravity

• Heatonly—two-wiresystems,power to open and close zone valves(Series20),andnormallyopen zone valves

• Heatonlywithfan

• Coolonly

• 750mVheatingsystems

This manual covers the following models• TH8110U:For1Heat/1Coolsystems

• TH8320U:Forupto3Heat/2Coolsystems

• TH8321U:Forupto3Heat/2Coolsystemswithdehumidification

(Pull thermostat from wallplate and turn over to find model number)

Need Help?Forassistancewiththisproductpleasevisithttp://customer.honeywell.com

or call Honeywell Customer Care toll-free at 1-800-468-1502

This thermostat contains a Lithium battery which may contain Perchlorate material.PerchlorateMaterial—specialhandlingmayapply, Seewww.dtsc.ca.gov/hazardouswaste/perchlorate

Installation Guide

269-2693—01

ENGLISH

MCR29481

+

+ +

MCR29480

Wallplate installation

1. Separate wallplate from thermostat.

2. Mount wallplate as shown below.

MERCURY NOTICEIfthisproductisreplacingacontrolthatcontainsmercuryinasealedtube,donot place the old control in the trash. Contact your local waste management authority for instructions regarding recycling and proper disposal.

Grasptopandbottomofwallplate and pull to remove from thermostat.

CAUTION: ELECTRICAL HAZARDCan cause electrical shock or equipment damage. Disconnect power before beginning installation.

Drill3/16”holesfordrywall.Drill7/32”holesforplaster.

Wallanchors

Wirehole Mounting screws

Must be installed by a trained, experienced technician• Readtheseinstructionscarefully.Failuretofollowtheseinstructions

can damage the product or cause a hazardous condition.

VisionPROTM TH8000 Series

3 69-2693—01

ENGLISH

NOTUSED

MCR29483

NOTUSED

MCR29482

For24VACprimarypower,connectcommonsideoftransformerto“C”terminal.

Insert supplied batteries for primary or backup power.

Power options

Push excess wire back into the wall opening. Plug wall opening with non-flammable insulation.

Remove factory-installed jumper only for two-transformer systems.

Conventional Terminal Letters:R Heating power. Connect to secondary

side of heating system transformer.Rc Cooling power. Connect to secondary

side of cooling system transformer.C Common wire from secondary side of

cooling transformer (if 2 transformers).W 1st stage heat relay.W2 2nd stage heat relay.Y 1st stage compressor contactor.Y2 2nd stage compressor contactor.G Fanrelay.S1 Optional outdoor or remote sensor.S2 Optional outdoor or remote sensor.

Heat Pump Terminal Letters:R Heating power. Connect to secondary

side of heating system transformer.Rc Cooling power. Connect to secondary

side of cooling system transformer.C Common wire from secondary side of

cooling system transformer.Y 1st stage compressor contactor.Y2 2nd stage compressor contactor.Aux/EAuxiliary/Emergencyheatrelay.G Fanrelay.L Heat pump reset (powered continuously

whenSystemissettoEmHeat;systemmonitorwhensettoHeat,CoolorOff).

O/B Changeover valve for heat pumps.S1 Optional outdoor or remote sensor.S2 Optional outdoor or remote sensor.

Terminal Designations Shaded areas below apply only to TH8320/TH8321.

Wiring

Installation Guide

469-2693—01

ENGLISH

Wiring guide—conventional systems

Wiring

1H/1C System (1 transformer)Rc Power [1]R [R+Rc joined by jumper]W Heat relayY Compressor contactorG FanrelayC 24VACcommon[3]S1 Optionaloutdoor/remotesensorS2 Optionaloutdoor/remotesensor

Heat Only SystemRc Power [1]R [R+Rc joined by jumper]W Heat relayC 24VACcommon[3]S1 Optionaloutdoor/remotesensorS2 Optionaloutdoor/remotesensor

Heat Only System (Series 20)Rc [R+Rc joined by jumper]R Series20valveterminal“R”[1]W Series20valveterminal“B”Y Series20valveterminal“W”C 24VACcommon[3]S1 Optionaloutdoor/remotesensorS2 Optionaloutdoor/remotesensor

2H/2C System (1 transformer)Y2 Cool relay 2W2 Heat relay 2Rc Power [1]R [R+Rc joined by jumper]W Heat relay 1Y Cool relay 1G FanrelayC 24VACcommon[3]S1 Optionaloutdoor/remotesensorS2 Optionaloutdoor/remotesensor

1H/1C System (2 transformers)Rc Power (cooling transformer) [1,2]R Power (heating transformer) [1,2]W Heat relayY Compressor contactorG FanrelayC 24VACcommon[3,4]S1 Optionaloutdoor/remotesensorS2 Optionaloutdoor/remotesensor

Heat Only System With FanRc Power [1]R [R+Rc joined by jumper]W Heat relayG FanrelayC 24VACcommon[3]S1 Optionaloutdoor/remotesensorS2 Optionaloutdoor/remotesensor

Cool Only SystemRc Power [1]R [R+Rc joined by jumper]Y Compressor contactorG FanrelayC 24VACcommon[3]S1 Optionaloutdoor/remotesensorS2 Optionaloutdoor/remotesensor

2H/2C System (2 transformers)Y2 Cool relay 2W2 Heat relay 2Rc Power (cooling transformer) [1,2]R Power (heating transformer) [1,2]W Heat relay 1Y Cool relay 1G FanrelayC 24VACcommon[3,4]S1 Optionaloutdoor/remotesensorS2 Optionaloutdoor/remotesensor

See [notes] below [1] Power supply. Provide disconnect means and overload protection as required. [2] Remove jumper for 2-transformer systems. [3] Optional24VACcommonconnection. [4] Common connection must come from cooling transformer.

Shaded areas below apply only to TH8320/TH8321.

VisionPROTM TH8000 Series

5 69-2693—01

ENGLISH

1H/1C Heat Pump (no auxiliary heat)Rc Power [1]R [R+Rc joined by jumper]O/B Changeover valve [5]Y Compressor relayG FanrelayC 24VACcommon[3]S1 Optionaloutdoor/remotesensorS2 Optionaloutdoor/remotesensor

2H/1C Heat Pump (with auxiliary heat)L Equipmentmonitor[6,7]Aux/E Auxiliary/Emergencyheatrelay(Heat2)Rc Power [1]R [R+Rc joined by jumper]O/B Changeover valve [5]Y Compressor relayG FanrelayC 24VACcommon[3]S1 Optionaloutdoor/remotesensorS2 Optionaloutdoor/remotesensor

2H/2C Heat Pump (no auxiliary heat)Y2 Compressor 2 relayRc Power [1]R [R+Rc joined by jumper]O/B Changeover valve [5]Y Compressor 1 relayG FanrelayC 24VACcommon[3]S1 Optionaloutdoor/remotesensorS2 Optionaloutdoor/remotesensor

3H/2C Heat Pump (with auxiliary heat)Y2 Compressor 2 relayL Equipmentmonitor[6,7]Aux/E Auxiliary/Emergencyheatrelay(Heat2)Rc Power [1]R [R+Rc joined by jumper]O/B Changeover valve [5]Y Compressor 1 relayG FanrelayC 24VACcommon[3]S1 Optionaloutdoor/remotesensorS2 Optionaloutdoor/remotesensor

Shaded areas below apply only to TH8320/TH8321.

Wiring guide—heat pump systems

Wiring

See [notes] below [1] Power supply. Provide disconnect means and overload protection as required. [3] Optional24VACcommonconnection. [5] O/B set to control as either O or B in installer setup. [6] If Lterminalisused,24VACcommon(terminalC)must be connected. [7] Heatpumpreset(poweredcontinuouslywhenthermostatissettoEm.Heat;systemmonitor

whensettoHeat,Cool,orOff).

Installation Guide

669-2693—01

ENGLISH

SCHED HOLD

TUE

FAN

AUTO

Inside

70

aM6:00

SYSTEM

HEAT

DONE

200120

DONE CANCEL

aM6:00

SYSTEM

HEAT

MCR29486

DONE

TUE

15

62012

DONE

TUE

PM1:00

MCR29485

MCR29484

Remove tab.

Align pins on back of thermostat with slotsinwallplate,thenpushgentlyuntil thermostat snaps into place.

Remove tab and mount thermostat

Set date and time

Press st to set time

Press st to set date

Press st to set month

Press st to set year

Installer setup

Press DONE to save changes. Press DONE to save and exit.

1. Press SYSTEM. 2. Press and hold these two buttons until the display changes.

3. Changesettingsas required (see pages7-9).

VisionPROTM TH8000 Series

7 69-2693—01

ENGLISH

DONE

200120

DONE

200120

MCR29486

Installer setup

SettingFunction

Press DONE to exit & save settings.Press st to select function

Press st to change setting

Setup functions Settings & Options (factory default in bold)

Shaded areas below apply only to TH8320/TH8321.

0120 Year (first two digits)

20 (2001-2099)21 (2100-2178)

0130 Year (second two digits)

12 (2012) [Otheroptions:00-99]

0140 Month 6 [Otheroptions:1-12]

0150 Date 15 [Otheroptions:1-31]

0160 Schedule format 4 7-day programming0 Non-programmable

0170 System type 1 1 heat/1 cool conventional2 1heat/1coolheatpump(noaux.heat)3 Heatonly(2-wiresystems)4 Heatonlywithfan5 HotwaterSeries20system(powertoopen&closezone

valves/normallyopenzonevalves)6 Coolonly7 2heat/1coolheatpump(withaux.heat)8 2heat/2coolmultistageconventional9 2heat/1coolmultistageconventional10 1heat/2coolmultistageconventional11 2heat/2coolheatpump(noaux.heat)12 3heat/2coolheatpump(withaux.heat)

0180 Fan control (heating)

0 Gas/Oil heat (equipment controls heating fan)1 Electricfurnace(thermostatcontrolsheatingfan)

0190 Changeover valve (O/B terminal)

0 O/B terminal controls valve in cooling1 O/Bterminalcontrolsvalveinheating

0200 Auxiliary heat 0 Electric backup heat1 Fossilfuelbackupheat

0210 External fossil fuel kit

1 External fossil fuel kit controls backup heat0 Thermostat controls backup heat (outdoor sensor required)

0220 1st stage com- pressor cycle rate

3 Recommended for most compressors [Otheroptions:1,2,4,5or6CPH]

0230 2nd stage com- pressor cycle rate

3 Recommended for most compressors [Otheroptions:1,2,4,5or6CPH]

Continued on next page

Installation Guide

869-2693—01

ENGLISH

Setup functions Settings & Options (factory default in bold)

Shaded areas below apply only to TH8320/TH8321.

0240 First stage heat cycle rate (CPH= cycles per hour)

5 Gas or oil furnaces of less than 90% efficiency1 Steam or gravity systems3 Hotwatersystems&furnacesof90%+efficiency9 Electricfurnaces [Otheroptions:2,4,6,7,8,10,11,12CPH]

0250 Second stage heat cycle rate (CPH)

5 Gas or oil furnaces of less than 90% efficiency1 Steam or gravity systems3 Hotwatersystems&furnacesof90%+efficiency9 Electricfurnaces [Otheroptions:2,4,6,7,8,10,11,12CPH]

0260 Third stage heat cycle rate (CPH)

9 Electric auxiliary heat or electric furnaces1 Steam or gravity systems3 Hotwatersystems&furnacesof90%+efficiency5 Gasoroilfurnacesoflessthan90%efficiency [Otheroptions:2,4,6,7,8,10,11,12CPH]

0280 Backlight 0 Backlight on for approx. 8 seconds after keypress1 Backlightalwaysonlowintensity,fullbrightafterkey-

press(requires24VACconnection)

0300 Manual/Auto changeover

0 Manual changeover (Heat/Cool/Off)1 Automaticchangeover(Heat/Cool/Auto/Off)

0310 Auto changeover deadband

3 Heat/cool temperature 3°F apart (1.5°C) ** See page 11 [Otheroptions:2-9(2°Fto9°F/1.5°Cto5°C)]

0320 Temperature display

0 Fahrenheit1 Celsius

0330 Daylight savings 2 Auto-change to daylight savings time(2007andbe-yond,forareasthatusethenew2007DSTcalendar)

1 Auto-changetodaylightsavingstime(through2006,andfor areas that do notusethenew2007DSTcalendar)

0 Daylight savings time is turned off

0340 Remote sensor 0 No remote sensor1 Outdoor sensor (display only)2 Outdoor control sensor (select heat pumps) ** See page 113 Indoor sensor

0350 Heat pump compressor lockout

0 No heat pump compressor lockout [Otheroptions:15,20,25,30,35,40°F(-9.5°Cto7°C)]

0360 Heat pump auxiliary lockout

0 No heat pump auxiliary lockout [Otheroptions:40,45,50,55,60°F(4.5°Cto15.5°C)]

0380 Dehumidification control

0 No dehumidification control1 Thermostatcontrolsdehumidificationwithairconditioner

** See page 11

Installer setup

Continued on next page

VisionPROTM TH8000 Series

9 69-2693—01

ENGLISH

Setup functions Settings & Options (factory default in bold)

0500 Furnace filter change reminder

0 Off1 10-day run time (about 1 month)2 30-dayruntime(about3months)3 60-dayruntime(about6months)4 90-dayruntime(about9months)5 120-dayruntime(about1year)6 365-dayruntime(about3years)

0510 Humidifier pad change reminder

0 Off1 90calendardays2 180calendardays3 365calendardays

0520 UV lamp change reminder

0 Off1 365calendardays

0530 Adaptive Intelligent Recovery™

1 On ** See page 110 Off

0540 Program periods 4 4 program periods (Wake, Leave, Return, Sleep)2 2programperiods(Wake,Sleep)

0580 Compressor protection

5 5 minute compressor off time ** See page 11 [Otheroptions:0,1,2,3or4-minuteofftime]

0600 Heat temperature range stop

90 Max. heat temperature setting is 90°F (32°C) [Otheroptions:40-89°F(4.5°Cto32°C)]

0610 Cool temperature range stop

50 Min. cool temperature setting is 50°F (10°C) [Otheroptions:51-99°F(10.5°Cto37°C)]

0640 Clock format 12 12-hour time (i.e., “3:30 pm”)24 24-hourtime(i.e.,“15:30”)

0650 Extended fan timer (heat)

0 Off90 Fanrunsfor90secondsaftercallforheatends

0660 Extended fan timer (cool)

0 Off90 Fanrunsfor90secondsaftercallforcoolingends

0670 Keypad lock 0 Keypad unlocked (fully functional)1 Partially locked (access to temperature settings only)2 Fullylocked

0680 Heat temperature control

2 Standard temperature control (recommended)1 Choose if room is warmer than set temperature3 Chooseifroomdoesnotreachsettemperature

0690 Cool temperature control

2 Standard temperature control (recommended)1 Choose if room is cooler than set temperature3 Chooseifroomdoesnotreachsettemperature

0700 Temperature display offset

0 Thermostat displays actual room temperature [Otheroptions:-3,-2,-1,1,2,3°Foffset(-1.5°Cto1.5°C)

0710 RESET 0 No reset1 Reset installer options & program schedule to factory

default (only date and time settings are retained)

Installer setup

Installation Guide

1069-2693—01

ENGLISH

DONE

200120

DONE

1

0TEST

MCR29488

Duringinstallersetup,presst repeatedlyuntil“Test”appears.

Test number

System status

Press st to select test

Press st to change status

Press DONE to terminate testing.

Shaded areas below apply only to TH8320/TH8321.

1 Cooling system 0 Compressor and fan turn off1 Compressor and fan turn on2 Second stage compressor turns on

2 Fan system 0 Fanturnsoff1 Fanturnson

3 Heating system 0 Heat and fan turn off1 Heatturnson(fanonifFunction0170issetforheatpump,

orifFunction0180issetto“1”)**Seepage62 Second stage heat turns on3 Thirdstageheatturnson

4 Emergency heating system

0 Heat and fan turn off1 Heat and fan turn on

System test System status

CAUTION: EQUIPMENT DAMAGE HAZARD. Compressor protection is bypassed duringtesting.Topreventequipmentdamage,avoidcyclingthecompressorquickly.

Installer system test

VisionPROTM TH8000 Series

11 69-2693—01

ENGLISH

Auto Changeover(SetupFunction0300):WhensettoAuto,thethermostatautomaticallyselectsheating or cooling depending on the indoor temperature. Heat and cool settings must be at least 2 de-greesapart.Iffunction0380issettoOn,theheatandcoolsettingsmustbeatleast5degreesapart.

Remote Sensor(SetupFunction0340):Ifanoptionaloutdoorsensorisinstalled,thethermostatcandisplaytheoutsidetemperature.Ifanoptionalremoteindoorsensorisinstalled,thethermostatwilldisplay the temperature at the sensor location (the internal sensor in the thermostat is not used).

Adaptive Intelligent Recovery(SetupFunction0530):Allowsthethermostatto“learn”howlongthefurnaceandairconditionertaketoreachprogrammedtemperaturesettings,sothetemperatureisreached at the scheduled time.

Compressor Protection(SetupFunction0580):Forcesthecompressortowaitafewminutesbeforerestarting,topreventdamage.Duringthistime,themessage“Wait”flashesonthedisplay.

Dehumidification control(SetupFunction0380):TH8321models monitor the indoor humidity level and automatically activate the cooling system to reduce humidity by lowering the temperature by up to3degreesbelowthecurrentcoolsetting.

Heat Pump Temperature Lockout (with fossil-fuelbackup):Ifthethermostatisinstalledwithanoptionaloutdoorsensor,youcanselectacompressorlockouttemperature(Function0350).Whentheoutdoortemperatureisbelowthelockouttemperature,onlytheauxiliaryheatoperates.Whentheoutdoortemperatureisabovethelockouttemperature,onlythecompressoroperates.

Heat Pump Temperature Lockouts (with electric heatbackup):Ifthethermostatisinstalledwithanoptionaloutdoorsensor,youcanselectacompressorlockouttemperature(Function0350)and/oranauxiliaryheatlockouttemperature(Function0360).Whentheoutdoortemperatureisbelowthecompressorlockouttemperature,onlytheauxiliaryheatoperates.Whentheoutdoortemperatureisabovetheauxiliarylockouttemperature,onlythecompressoroperates.Iftheoutdoortemperatureisbetweenthecompressorandauxiliarylockouttemperatures,boththecompressorandauxiliaryheatcan operate.

Shaded areas below apply only to TH8320/TH8321.

Special functions

Please contact your distributor to order replacement parts.Outdoor temperature sensor .............................. PartNumberC7089U1006Remote indoor temperature sensor .................. PartNumberC7189U1005Cover plate* ............................................................ PartNumber32003796-001*(Use to cover marks left by old thermostats.)

Accessories & replacement parts

Installation Guide

Honeywell International Inc.

1985DouglasDriveNorth

GoldenValley,MN55422

http://customer.honeywell.com

Automation and Control Solutions

® U.S. Registered Trademark.© 2012 Honeywell International Inc.69-2693—01M.S.01-12Printed in U.S.A.

Temperature Ranges• Heat:40°to90°F(4.5°to32°C)• Cool:50°to99°F(10°to37°C)

Operating Ambient Temperature• 0°to120°F(-18°to48.9°C)

Shipping Temperature• -30°to150°F(-34°to66°C)

Operating Relative Humidity• 5%to90%(non-condensing)

Physical Dimensions• 4-9/16”Hx6”Wx1-3/8”D• 116mmHx152mmWx35mmD

Electrical Ratings

Terminal Voltage(50/60Hz) RunningCurrent

WHeating 20-30Vac 0.02-1.0A

(Powerpile) 750mVDC 100mADC

W2Heating 20-30Vac 0.02-0.6A

YCooling 20-30Vac 0.02-1.0A

Y2Cooling 20-30Vac 0.02-0.6A

Aux/EAux.heat 20-30Vac 0.02-1.0A Emergencyheat

O/BChangeover 20-30Vac 0.02-0.6A

LHeatpumpreset 20-30Vac 0.02-0.6A

Specifications

Need Help?Forassistancewiththisproductpleasevisithttp://customer.honeywell.com

or call Honeywell Customer Care toll-free at 1-800-468-1502

By using this Honeywell literature, you agree that Honeywell will have no liability for any damages arising out of your use or modification to, the literature. You will defend and indemnify Honeywell, its affiliates and subsidiaries, from and against any liability, cost, or damages, including attorneys’ fees, arising out of, or resulting from, any modification to the literature by you.