Customer Customer PO# SE:

CATALOG #: KVA: QTY: SO#: PART#:

PHASE: FLUID: TEMP: COOLING: HERTZ: CONDUCTOR: AMBIENT:

THREE TYPE II OIL 65 C ONAN 60 HZ # ALUMINUM 30 C avg.

SINGLE VOLT ESSO 55 C ONAN / ONAF-FFA 50 HZ # COPPER 40 C avg.

ENVIROTEMP(FR3) 55/65 C ONAN / ONAF-less fans OTHER

BIOTEMP OTHER ONAN / ONAF

SILICONE NOTE: If less flammable fluid 5 LEGGED CORE

GROUNDING is used, rating is KNAN or KNAF TERTIARY

RECTIFIER: PULSE respectively. TRIPLEX CORE/COIL

HIGH VOLTAGE TAPS: LOW VOLTAGE

HV: 2-2 1/2% FCAN & BN LV:

BIL: kV 4-2 1/2% FCBN BIL: kV

CONNECTION: 2-2 1/2% FCAN & 4-2 1/2% FCBN CONNECTION:

DELTA OTHER DELTA

WYE With single Phase Mid-Tap Coil

HO Bushing w/full BIL HO Ground Strap ES SHIELD WYE

Neutral internal & isolated BALANCED TAPS XO bushing

Neutral internally grounded WET WIND XO bushing w/ground strap

GROUNDED WYE (HO-XO Comm.) GROUNDED WYE (XO-HO Comm.)

DELTA-WYE IMPEDANCE: % DELTA-WYE

ZIG ZAG MIN NOM MAX ZIG ZAG

VECTOR CONNECTION:

HV CONFIGURATION: HV BUSHINGS LV BUSHINGS:

Radial Feed LIVE FRONT or . . . DEAD FRONT Standard

Loop feed 5/8" eyebolt Wells 4-hole spade

Dual Radial feed 2-hole G spade INSERTS FACTORY INSTALLED 6-hole spade

(Alternate Source) OTHER Inserts QTY LB NLB 8-hole spade

6 Bushings (RADIAL FEED) Feed thru QTY 10-hole spade

3 for incoming feeders One Pc. 200A LB 12-hole spade

3 for arresters Cable Supports One Pc. 600A Deadbreak OTHER

Other Bushing Supports

Cable Supports Lugs

ACCESSORIES: FUSES: STANDARD FAN PACKAGE

Thermometer (std) Internal Weak Link Without Fans

w/ 2 contacts ** w/ 3 contacts ** Bay-o-net With Fans

Liquid Level Gauge (std) Dual Sensing Fault (Current) Sensing Explosion Proof

w/ low contact ** w/ 2 low contacts ** High Current Partial Range ELSP CL back-up CPT

w/ high & low contacts ** ELS BON (current limiting) Fan Voltage

Pressure Vacuum Gague (std) Drywell Canisters Run from Oil Temp Wind Temp

w/ contacts** Non-Loadbreak - INTERLOCKED

Bleeder Valve (std. above 2500 kVA) Loadbreak ARRESTERS: TRIAL FIT & SHIP SEPARATE

Winding temp therm 2 contacts 3 contacts NX Clip Style

Sudden Pressure Rise Relay Arc Strangler Fused Switch Dead front MOVE kV

Seal in relay V AC DC AC/DC Spares QTY Distribution Class kV

Pressure Relief Valve (std. on all units) OTHER Intermediate Class kV

Pressure Relief Device (std. above 2500 kVA) Station Class kV

w/contacts semaphore shroud SWITCHES: Internal Under Oil kV

Resistance Temp Detector w/ 4-20mA On-Off (2 position)

Gas Sample Valve (std) Qty Amps Qty Amps SECONDARY METERING & PROTECTION:

Bolted Tank Cover Dual Radial (A/Open/B/Open) KWH Meter type:

1" fill plug & filter press conn (std 2500 & below) Loop Feed "V" Blade Stainless Steel Socket

1" fill valve (std above 2500 kVA) ** Loop Feed "T" Blade Socket Only

1" DV&S (std 2500 kVA & below) Dual Voltage Switch Panelboard Amps:

2" DV&S (std above 2500 kVA) ** Delta-Wye Switch Mounting Provisions Only

Key Interlock * Switch Interlocked w/Fuse Holders Secondary Circuit Breaker

Provisions ONLY Amps: Qty:

Phase Barriers HV LV AUX WIR CABINET TYPE: Line Lugs Load Lugs

Front Barriers HV LV ALL WIRING IN RIGID CONDUIT Supplied by others-Manufacturer installed

Seismic Anchoring Pads STRIP HEATER, BREAKER & THERM Mounting provisions only

Pentahead Locking Device (std) WIR CAB HV COMP LV COMP PT Ratio:

Hexhead Locking Device ** CT Ratio(s):

** in lieu of standard * location

PADMOUNT SPECIFICATION SUMMARY SHEET

HV LV

QF5226 Page 1

Orig Issue Date: 2/9/2009

C/O Date:____________ Rev. 12/31/2008

Customer Customer PO# SE:

CATALOG #: KVA: QTY: SO#: PART#:

EXACT DUPLICATE to: SPECIAL DIMENSIONS:

PART# SERIAL#

SIMILAR to:

PART# SERIAL#

Maintain Dimensions

Exceptions:

DRAWING/PHOTOS attached

DRAWING REF#

RADIATORS

STAINLESS STEEL (refer to S.S. section) MANUFACTURER'S ID PLATE CUSTOMER ID PLATE

GALVANIZED NOT PAINTED UL LABEL Required Non-PCB Label (Std)

REMOVABLE RADIATORS UL FAN MODIFICATION Danger Signs

SHIPPED INSTALLED ID TAG# Qty

SHIPPED SEPARATELY

PAINT COLOR: (Standard finish is industrial enamel) MISCELLANEOUS ITEMS

Padmount Green ASA 24 CONTAINMENT PAN

ASA 61 ASA 49 BRACED FOR FULL VACUUM FILLING

ASA 70 OTHER BRACED FOR MINE DUTY

PAINT TYPE: HIGH ELEVATION :

STANDARD BRACED FOR % TILT

TOUCH-UP PAINT POSITIVE PRESSURE NITROGEN SYSTEM

EPOXY MASTIC UNDERCOAT STEP-UP DUTY GENERATOR STEP-UP DUTY

EPOXY PAINT & PRIMER BRACED FOR MOTOR STARTING:

EPOXY PRIMER ONLY SOFT START ACROSS THE LINE

DURETHANE OVERLOAD:

CARBOLINE NON-SINUSOIDAL LOAD OF K-FACTOR

OTHER CORE GROUND BUSHING

STAINLESS STEEL 304L 316L SPECIAL STANDARD AND/OR LOSS/EFFICIENCY REQUIREMENTS:

BASE CSA STANDARD REQUIREMENTS CSA STANDARD REQUIREMENTS

COMPARTMENT CSA C2.1-06 (Distribution) CSA CSA C88-M90 (Power)

HARDWARE (nuts, bolts, studs, washers) CSA C802.1 (High Efficiency) CSA C802.3 (Maximum Losses)

RADIATORS (SS valve not available) CSA C227-.4-2007 (Dead Front) TP1 EFFICIENCIES

NOT PAINTED CSA C802.1 (High Efficiency) DOE EFFICIENCIES

FILL / DRAIN VALVE without sampler CSA C227.2-88 (Live Front)

CSA C802.1 (High Efficiency)

CUSTOMER SPECIAL REQUIREMENTS SPECIAL SHIPPING REQUIREMENTS

WITNESS TESTING PALLET

FINAL INSPECTION POSITIVE PRESSURE NITROGEN BLANKET

ANSI FULL SERIES IMPULSE TEST IMPACT RECORDER

ANSI MODIFIED SERIES IMPULSE TEST CUSTOMER SUPPLIED:

ANSI SOUND LEVEL TEST SHIPMENT DETAILS REQUIRED PRIOR TO SHIPMENT

ANSI TEMPERATURE RISE TEST FOR CUSTOMER TAGGING

DISSOLVED GAS ANALYSIS ITEMS THAT MUST SHIP WITH TRANSFORMERS

SPECIAL OIL TEST REQUIRED. SEE QF5623A

OTHER: OTHER:

SPECIAL ITEMS & SPECIFICATIONS:

PADMOUNT SPECIFICATION SUMMARY SHEET

NOT PAINTED

TANK (parking stands, jack lugs, rectangular

handhole cover, PRD ring, PRD cover)

NOTE: Engineering decides if fluid ships in

tank or barrels (indicated on construction

note)

QF5226 Page 2

Orig Issue Date: 2/9/2009

C/O Date:____________ Rev. 12/31/2008