Vaxcare:AUST: 1300 36 4040NZ: 0800 800 900Vaxcare:AUST: 1300 36 4040NZ: 0800 800 900www.vax.com.auInstruction ManualMODIFIED AUGUST 2008Please read carefully before using this cleaner.Always fully extend the mains cable before use.Retain for future reference.MultifunctionInstruction ManualModel No. V2000 - Sukka - VHN - Pet VAX - Family VAXVAXCARE Service & Help:AUSTRALIA 1300 36 4040NEW ZEALAND 0800 800 900If you have any queries or concerns about using your Vax, call VAXCARE. Please make a note of the part number or model number of the appliance before calling. (Aust only: Mon-Fri. 10.00am to 6.00pm. EST)Calls are charged at the local rate.An answerphone is available out of these hours. There are over 300 approved Vax Service Agents in Australia and New Zealand. For the nearest Service Agent, please refer to your Vax warranty or call VAXCARE or visit www.vax.com.auTechnical SpecicationWeight:Net 8.0KgSize:Height 54cms x 34cms diameterMotor:1200 watts max. / 450 watts min variable power. 2 stage bypass motor completely insulated and sealed against water contamination.Structure:Moulded high-impact resistant ABSDust Bags: Supplied with machine.Clean Water Reservoir:4 litres of clean water.RecoveryBucket:8 litre capacity.Hose:1.8m long, crush resistant hose with 360 (degree) swivels at each end.Subject to technical change without notice.21. Important Safety InformationTHIS EASY GUIDE SHOULD BE READCOMPLETELYANDREFERREDTOAT ALL TIMES BEFORE USING YOUR VAX.This easy guide should be retained with your VAX for future reference.IfyourVAXissoldortransferredtoanew owner,thisguideshouldbepassedonso that the new owner can become acquainted withthemachineandthisinformation.The following information is provided in the interest of safety.Please read it before using your VAX.DOSUse only genuine VAX replacement parts.Use of non VAX uids, lters and accessories maydamageyourmachineandvoidyour warranty.Ensurethemainscableisfullyunwound and straightened before use.Ifthesupplycordisdamaged,itmustbe replaced by the manufacturer or its service agent or a similarly qualied person in order to avoid a hazard.Ensurethemainscableiskeptwellaway fromtherevolvingbrushes(wheretted) ofyourVAX,whenitisturnedonand running.Keep the mains cable away from heat, oil, sharp edges and rough surfaces and avoid damage in any other way.Exerciseextremecarewhencleaningstair carpets. Ensure that your VAX is in a stable positionateitherthetoporbottomofthe stairswithoutover-stretchingthehose orcable.Whencleaningthestairtreads, always keep a hand rmly on your VAX. You may prefer to remove the castors.Followtheinstructionsinthisuserguide when tting accessories or tools.Remove the plug from the wall socket before carryingoutanymaintenancespeciedin this guide.Changedustbagandltersatregular intervals.Store your VAX in a dry place.HaveyourVAXservicedbyanauthorised VAX Service Agent only using genuine VAX spare parts.DONTSThisapplianceisnotintendedforuse byyoungorinrmpersonsunlessthey havebeenadequatelysupervisedbya responsible person to ensure that they can use the appliance safely.Youngchildrenshouldbesupervised toensurethattheydonotplaywiththe appliance.Never drag your VAX by the mains cable.Never tug at the mains cable to remove the plug from the wall socket.Neverallowthecompletecoiledmains cable to drop on the oor as this may result inkinksorknotsoccurringinthecable, causing premature failure.Dontletanyonetouchtherotatingbrush bar(wheretted)unlessyourVAXis disconnected from the mains.NeveruseyourVAXinthepresenceof ammable gases.Avoidsuckinguphotitems,hazardous liquidsoranyothermaterialwhichcould damage your VAX.Never leave your VAX running unattended.Never use your VAX without a dust bag.If your VAX fails to operate, never attempt to repair it yourself as repairs carried out by an unauthorised or inexperienced person may cause injury to you or damage to your VAX and void your warranty.Never alter the specication or modify your VAX in any way.EXTENSION CABLEIf using an extension cable always ensure that the insulation sheath is in good condition and is not damaged in any way.Make sure that the plug and socket are tted totheextensioncablecorrectly,ifindoubt have it checked by a qualied electrician.Always use the extension cable in accordance with the manufacturers instructions.IMPORTANT:Whencarryingoutany maintenanceorcleaningoperationsonthis product, it is essential that the plug is removed from the wall socket.In the interests of product improvement, theCompanyreservestherightto introducemodicationsoralterations without notice.112. TheSockFilterthat encasestheHEPA lter,actsasapre-lterandprotectsit fromthemajorityof dust.TocleantheSock FiltergentlypeelitbackfromtheHEPA (Fig/14.2).Shaketoremovetheexcessdirtand handwashatnormaltemperature.Do notmachinewashortumbledry.Donot replacethesockwhenitisstilldampor wet.WhenreplacingtheSockFilteronthe HEPA ensure that the sock is pulled down completely all round.TheSockFiltercanbecleanedupto 5timesinthiswayandshouldthenbe replaced.3. Withthesockremoved,theHEPAFilter canbecleanedbygentlytappingona hard surface. The HEPA Filter should never be washed or exposed to water.VAX recommends that the HEPA Filter be replaced every 12 months to maintain peak performance.TIPThe HEPA lter can also be cleaned by taking the vacuum outside, removing the HEPA and vacuumingtheHEPAonlywiththedusting tool.Ensureallltersarereplacedbefore vacuuming your home.15. Removing debris from the Mini TurboTool(Model: Pet VAX only. Optional with other models.)1. Switchthe vacuumcleaner off and disconnect thepowerplug from the electrical outlet.Rotate orremove thelockingring (Fig/15.1).2. Liftthetopcover off and remove any debris (Fig/15.2).3. Tore-assemble, ensurethatthe tabs are engaged. Pivotthelower housing closed and rotateorreplace thelockingring 180 (Fig/15.3).16. Removing hair from TurboBrush(Model:PetVAX&FamilyVAXoroptional extra with other models).Over time hair and lint will build up around the brushbar. This must be removed to maintain performanceandpreventdamagetothe tool.1. Switchthevacuumcleaneroffand disconnectthepowerplugfromthe electrical outlet.2. Turnthebrushbar overandusingapair ofscissorsrunthe bottom blade along the length of the brushbar cutting the hair as you go (Fig/16.1).USE SCISSORS WITH THEPOINTOFTHE BLADEAWAYFROM YOUR BODY.3. Once the hair and lint around the brush bar hasbeencut,removethehairoutofthe brushes.17. StorageIMPORTANT:Alwaysunplugthevacuum cleanerfromtheelectricaloutletandrewind the power cord as directed before storing.NOTE:Alwaysstorethevacuumcleaner base down.Replacement3 Filter PackDisposable PaperBags Pack (5)ReplacementCloth BagMoulded ConeFilter Pack (2)P/N 90630 P/N 90600 P/N 90620 P/N 20310HEPA Filter & SMS Filter CoverP/N 905005. Thewashingtoolisatonthesurface being washed.6. Thepowercontroliscorrectly adjustedwithinthewashing range.Turnhigherthan minimumwashsettingfor uneven or higher pile if required (Fig/12.4).7. There are no kinks in the solution tube.Remove kinks by rubbing the tube between nger & thumb8. That the recovery bucket is not full, causing theautomaticcutoffvalvetostopthe suction.32. Parts Checklist1012. If You Have Washing DifcultiesIF YOU HAVE WASHING DIFFICULTIES, CHECK...1. The pump washing button is switched on.2. The tube valve is properly connected (Fig/12.1).Before using your VAX, please read Important safety information on page 2.All VAX Multifunctions include:3. The weight on the end ofthesolutiontubeis atthebottomofthe waterreservoirand nottrappedbetween themotorandwater reservoir (Fig/12.2).4. Therocker switchis posi ti oned t o w a r d s theback (Fig/12.3).13. Looking After Your VAXItemsbelowareavailablefromyourVax Retailer or from VAX direct.REGULARLY (when you buy a new pack of5disposablepaperbagsor1new cloth bag)Replace cone lterAvailableinapack oftwo.Alsoavailable withabondinilterand exhaust lter in a 3 lter pack.Clean the Bondini lterAvailablewithacone lter and exhaust lter in a 3 lter pack. Wash lter in warm water. Squeeze itdryandreplaceit. Your VAX will work more efciently if the Bondini lter is replaced with a new one occasionally.Clean the exhaust lterAvailablewithacone lter and bondini lter in a 3 lter pack. Wash lter in warm water. Squeeze dry and replace.Filter housing unitMotor unitWater reservoirFlexible Suction Hose and Hand gripStainless Steel Extendible WandDust bagsVAXCarpetCleaningFluidCombination toolUpholsteryToolDustingBrushCrevice toolUpholsterywashing toolRecovery bucketFibreflow CarpetWashing ToolLiquid Delivery TubeOn/off switchVariablespeedcontrolPump on/off switchHyrdo Dry HardFloor Wash HeadHEPAfilterSpillPick-up ToolMiniTurbo BrushTurbo BrushHard Floor BrushOther Accessories:14. Looking After Your HEPA Filter (Model Family VAX and Sukka only. Optional extra with other models. Contact VAXCARE for information)1. RemovetheHEPA Filterbyturning a n t i c l o c k w i s e (Fig/14.1).1. Set up for washing, but dont connect the solutiontubeorputwaterinthewater reservoir (Fig/11.1).Ifthespillissoapy,VAXDefoamerwillbe requiredin therecovery bucket.Refer toinstructions onDefoamer bottle. 2. Use the metal extension tube or extendible wand or connect the washing tool directly to the hand grip.3. Turn the suction power tomaximumand switch on (Fig/11.2).4. Suck up the spill.ThesoundyourVAXmakeswillchange and the suction will drop when the recovery bucket is full. Time to empty it!3. Dry Vacuuming1. Fitadustbagby pushing it rmly into the recovery bucket beforeconnecting hose (Fig/3.1).2. Push the connector on the end of the hose. Turn it clockwise to lock (Fig/3.2).3. Fitthelterhousingandmotortothe recovery bucket.Ensure the two retaining clips are secured. Youmayhavetopushdownhardonthe edgesofthemotorunitabovetheclips. They are a tight t (Fig/3.3).4. Fittheextendible wandtothehose hand grip.Adjustwand length by pressing buttoninthe directionofthe arrow (Fig/3.4).5. Choosesuctionpowerbyturningthedial located at the front of the motor.Vacuum carpets on high power.Vacuumfabricsandupholsteryonlow power.6. Choose the right tool for the job.The smaller tools can be tted to the back of your VAX when not in use.7. Switch on and begin vacuuming.TIPAs your VAX is very powerful, you may nd thatthedustbagllsupquicklytherst time you use it.Shouldablockageoccurinthesuction hose/hand grip it can usually be unblocked byreversingthehoseandrunningthe machine for a few seconds or so. It may be necessary to bind the hand grip end of the hose with a cloth to form a temporary seal betweenthehandgripandtheconnector socket on the recovery bucket.UpholsteryTool:Foruseoncarpet, upholstery, stairs etcDustingBrush:Forcleaningdelicate surfaces.Crevice Tool: For cleaning in narrow gaps.MiniTurboBrush:RotatingBrushBar dislodges hair and lint from upholstery (Model: Pet VAX only).Combination Tool: Use the lever to switch between vacuuming hard oors and carpets.Turbo Brush: Rotating Brush Bar dislodges hairandlintfromcarpets(Model:PetVAX and Family VAX only).SpillPick-upTool:Takesupsmallliquid spills (Model: Pet VAX only).For information on accessories contact VAXCARE.4 910. How to Unblock Sinks1. Set up for washing, but dont connect the extendible wand, solution tube or put water in the water reservoir.Ifthewaterinyoursinkissoapy,VAX Defoamerwillberequiredintherecovery bucket. 2. Wrapacloth aroundthe bent end tube tocreatea sealbetween thetubeand theplughole (Fig/10.1).3. Turnthesuctionpowertomaximumand switch on.ThesoundyourVAXmakeswillchange and the suction will drop when the recovery bucket is full. Time to empty it!11. How to Suck Up Large SpillsIf your washing machine oods or the deepfreeze has been defrosted, leaving pools ofwater about, your VAX can help.Fig/11.2 Fig/10.19. What to Do After WashingAFTER WASHING - ALWAYSKeep your VAX assembled. Clean the washing tool, stainless steel wand and hose, by sucking up some clean warm water. After sucking up thewater,leaveyourVAXswitchedon.Air owing through the hose will help dry it out.AFTER WASHINGClean out the washing toolstopreventdirt andresiduefrom drying out (Fig/9.1)8 51Vacuum the area you intend to wash.2Removethemotorlterhousing,hose, dust bag and vacuuming tool.3Whendustbagis removed, re-t the hose.Pushand turnclockwise (Fig/5.1).4Fill the water reservoir withwarmwater (nothot),tothelevel markedonit.Fitthe waterreservoirinto therecoverybucket (Fig/5.2).5AddVAXCarpet Cleanertotheclean water.Refertothe instructionsonthe carpet cleaner bottle.8. How to Wash Hard Floors(Model Family VAX only. Optional with other models.) 1. SetupyourVaxasdescribedonpage5 changingthecarpetcleaningsolutionfor hard oor solution. 2. ConnecttheHydro-dryhardoorwash head to the end of the extendible wand and t the solution tube to the Hydro-dry head. 3. Switch the power button ON. 4. Turn suction power to wash setting.5. Start the washing solution owing. To start thesolutionowthroughthewashhead, push down the rocker switch on the Hydro dryheadsothattheswitchispushed towards you (Fig/8.1).This also lowers the sponge and brushes to scrub the oor surface (Fig/8.2).6.Glidethe Hydro-dry headbackand forth overtheoorsurface.Washanareaof around 3 square metres.7.Tostopthewashingsolutionow,push therockerswitchforward.Thiswillalso raisethespongeandbrushesexposing rubber blades. 8.Turn the suction power to maximum.9.ContinuetomovetheHydro-dryhead overtheoorsurfacetopickupexcess water.10. Move to the next area and repeat steps 3 to 9.Sponge &Brushes4. How to Use theSpill Pick-up Tool (ModelPetVAXonly.Optionalwithother models. Contact VAXCARE for information)The Spill-pick up tool can be used while dry vacuuming to pick up small liquid spills.1. Attachthespill pick-uptoolto thevacuuming hose.TurnyourVAX on.Suckupthe spillkeeping thespillpick-up facingdown.Do not overll above themaxlevel mark (Fig/4.1). NOTE: Do not tip the tool upside down or the uid will leak out.2. Removethespillpick-up from the hose.Releasetheconnector bypushingtheblack release button and pull to disconnect.Disposethe spill (Fig/4.2).Fig/4.25. Getting Ready to Wash3 ITEMS OUTFilter housing unit3 ITEMS INWater reservior with water and carpet cleanerLiquid delivery tube Dust bagWashing tool Vacuuming tool3. Separatethepartsand rinse.Drycomponentsbefore replacing (Fig/4.3).NOTEThespillpick-upis designed to pick-up uid. Anystainingormarking canbewashedusing yourVAXttedwiththe appropriate washing tool.9.Tostopthesolutionow,pullthecollar onthewashtoolbackward.Goback over the area you have just washed. This willremoveexcessmoisturefromthe upholstery (Fig/7.3).10. Move to the next area and repeat steps 6 to 9.11. Whennomorewaterreachesthewash tool the pump will make a sound due to sucking air.Rellthewaterreservoirwithwaterand VAXCarpetcleaner.Emptytherecovery bucket when you rell the water reservoir. The sound your VAX makes will change andthesuctionwilldropiftherecovery bucket is full. Time to empty it!TipUsetheupholsterywashingtoolforspot cleaning small patches on either carpet or upholstery.6 76. How to Wash Carpets1. Set up your VAX as described on page 5.2. Switch ON.3. Switch on the power washing button.4. Turnthesuction powertothewash settingorhigher, dependingonthe carpet pile (Fig/6.1).5. To allow water to ow through the Fibreow wash head, ensure that the rocker switch (A)ispositionedtowardsthebackofthe wash head (Fig/6.2).6. Withthesolutionowing,washasection ofcarpetapprox3metresx3metresby pushingthewashheadbackwardsand forwards over the area.7. Stopthesolutionowbymovingthe rocker switch (A) to the forward position on the Fibreow wash head. This will prevent waterow,allowingexcesswatertobe removedfromthesectionjustwashed (Fig/6.3).8. Turn the pump washing button off and turn the suction power to maximum.Gobackovertheareayouhavejust washed.Thiswillnowextractexcess moisture from the carpet.9.Move to the next area and repeat steps 3 to 8.10. Whennomorewaterreachesthewash tool the pump will make a sound due to sucking air.Rellthewaterreservoirwithwaterand VAXCarpetcleaner.Emptytherecovery bucket when you rell the water reservoir. The sound your VAX makes will change andthesuctionwilldropiftherecovery bucketisover-full.Timetoemptyit! (Fig/6.4)TipALWAYSTESTFORCOLOUR FASTNESSWITHSOMEUNDILUTED CARPETCLEANERONAHIDDEN AREA FIRST.Startfromthecornerofaroomandwork backwards towards the door.Ifyouarewashingverydirtycarpets,you may have to wash them several times over aperiodoftimetobringallthedirttothe surface.Whenwashingstairs,placeyourVAX above the area you are washing. ALWAYS ENSUREYOURVAXISSTABLE.The castorsonyourVAXwillpulloff,givingit extra stability on stairs or slopes. DO NOT PULL EXCESSIVELY ON THE HOSE.Metalorwoodenfurniturelegsmaymark awetcarpet.Waituntilthecarpetisdry orplacealuminiumfoilunderthefeetof furniture.When washing deep pile carpets, move the washingtoolinthesamedirectionasthe pile lays.Dontallowchildrenoranimalsontothe carpet until it is dry.7. How to Wash Upholstery1.SetupyourVAXasdescribedonpage 5,BUTdontusetheextendiblemetal wand.2.Connecttheupholsterywashingtoolto theshortbentendandwindtheexcess solution tube around a portion of the hand grip.Connectthetubetotheupholstery washing tool (Fig/7.1).3.Switch power button ON.4.Switch ON the pump washing button.5.Turnthesuctionpowertothewash setting.6.To start the solution ow, push the collar on the wash tool forward (Fig/7.2).7.When you see water swirling in the washing tool you are ready to start washing.8.Draw the washing tool backwards across the upholstery. Cover a small area at a time. Dont push thetoolbackwardsandforwardsasthis may stretch the fabric.6.Wrap Solution Tube (A) to Hose (B) using Clipsprovided(C) toholditinplace. Ensurethatthe solutiontubeis wrappedloosely enoughtoallow the solution to ow freelythroughthe tube (Fig/5.3).7.Fittheextendiblewandtothesuction hose.8.Fit the washing tool andpushendof SolutionTubeonto connectingvalve ontheCarpet/ UpholsteryWash Tool (Fig/5.4).TIPToachievecorrectlengthlaytubewithclips parallel to hose and wand before attaching.9.Unclip the transparent tube on the bottom of the motor unit. Ensure the tube is positioned atthebottomofthe washingsolution (Fig/5.5).10. Fitthemotorunit (makesurethe transparenttubeis nottrappedwhen youdothis)Secure clipsonbothsideof motor.11. Locatethetube valve, push in rmly and turn clockwise (Fig/5.6).YOUARENOW READYTOSTART WASHINGTIPIfyourcarpethasbeenpreviouslywashed withahighfoamingshampoo,pourVAX Defoamer into the recovery bucket.VAX Defoamer is available through your VAX Stockist.