6200 Gas/LPG CE Operarot Manual (En)az295482.vo.msecnd.net/globalassets/globalassets/all...

6200

*330379*

330379Rev. 12 (4-2012)

(Gas/LPG)

SweeperEnglish EN

Operator Manual

To view, print or downloadthe latest manual, visit:

www.tennantco.com/manuals

This manual is furnished with each new model. It provides necessary operation and maintenance instructions.

Read this manual completely and understandthe machine before operating or servicing it.

This machine will provide excellent service. However, the best results will be obtained at minimum costs if:

S The machine is operated with reasonable care.

S The machine is maintained regularly - per the machine maintenance instructions provided.

S The machine is maintained with manufacturer supplied or equivalent parts.

PROTECT THE ENVIRONMENTPlease dispose of packaging materials,old machine components such asbatteries, hazardous fluids such asantifreeze and oil, in an environmentallysafe way according to local wastedisposal regulations.

Always remember to recycle.

MACHINE DATAPlease fill out at time of installation for future reference.

Model No. --

Serial No. --

Machine Options --

Sales Rep. --

Sales Rep. phone no. --

Customer Number --

Installation Date --

Tennant N.V.Industrielaan 6 5405 ABP.O. Box 6 5400 AA Uden--The [email protected]

Specifications and parts are subject to change without notice.

Original instuctions, Copyright E 1999--2003, 2005--2008, 2010, 2012 TENNANT Company, Printed in The Netherlands

DECLARATION OF CONFORMITY FOR MACHINERY(according to Annex II A of the Machinery Directive)

TENNANT N.V.

Industrielaan 6 5405 ABP.O. Box 6 5400 AAUden -- The NetherlandsUden, 21--05--2010

EN

Herewith declares, on our own responsibility, that the machinery

6200-- is in conformity with the provisions of the Machinery Directive (2006/42/EC), as amended and with nationalimplementing legislation

-- is in conformity with the provisions of the Electro Magnetic Compatibility Directive 2004/108/EC-- is in conformity with the provisions concerning noise emission for outdoor use (Directive 2000/14/CE) andwith national implementing legislation

and that-- the following harmonized standards or parts of these standards have been applied: EN ISO 14121--1, EN1037, EN 60335--1, EN 60204--1, EN ISO 13849--1, EN ISO 13849--2, EN 60529, EN ISO 4413, EN 349, EN55012, EN 61000--6--2, EN ISO 11201, EN ISO 4871, EN ISO 3744*, EN ISO 13059*, EN ISO 3450, EN60335--2--72.

-- the following national standards or parts of these standards have been used:

CONTENTS

16200 Gas/LPG 330379 (2--2010)

CONTENTS

PageCONTENTS 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . .SAFETY PRECAUTIONS 2. . . . . . . . . . . . . . . . .OPERATION 4. . . . . . . . . . . . . . . . . . . . . . . . . . . .

OPERATOR RESPONSIBILITY 4. . . . . . . . .MACHINE COMPONENTS 5. . . . . . . . . . . . .SYMBOL DEFINITIONS 6. . . . . . . . . . . . . . . .CONTROLS AND INSTRUMENTS 7. . . . . .OPERATION OF CONTROLS 8. . . . . . . . . .

DIRECTIONAL PEDAL 8. . . . . . . . . . . . . .BRAKE PEDAL 9. . . . . . . . . . . . . . . . . . . .PARKING BRAKE PEDAL 9. . . . . . . . . . .LARGE DEBRIS TRAP PEDAL 9. . . . . . .IGNITION SWITCH 10. . . . . . . . . . . . . . . . .HORN BUTTON 10. . . . . . . . . . . . . . . . . . . .SIDE BRUSH LEVER 10. . . . . . . . . . . . . . .OPERATING LIGHTS SWITCH

(OPTION) 11. . . . . . . . . . . . . . . . . . . . . .OPERATING/HAZARD LIGHTS

SWITCH (OPTION) 11. . . . . . . . . . . . . .MAIN BRUSH LEVER 12. . . . . . . . . . . . . . .CHARGING SYSTEM LIGHT 12. . . . . . . .LOW OIL WARNING INDICATOR 12. . . .FUEL LEVEL GAUGE 13. . . . . . . . . . . . . . .GASOLINE ENGINE CHOKE KNOB 13. .VACUUM FAN/FILTER SHAKER

SWITCH 14. . . . . . . . . . . . . . . . . . . . . . . .STEERING WHEEL 14. . . . . . . . . . . . . . . .HOURMETER 14. . . . . . . . . . . . . . . . . . . . .HOPPER SWITCH 15. . . . . . . . . . . . . . . . .HOPPER DOOR SWITCH 15. . . . . . . . . . .CIRCUIT BREAKERS 16. . . . . . . . . . . . . . .OPERATOR SEAT 17. . . . . . . . . . . . . . . . . .ADJUSTABLE OPERATOR SEAT

(OPTION) 17. . . . . . . . . . . . . . . . . . . . . .DELUXE SUSPENSION SEAT

(OPTION) 17. . . . . . . . . . . . . . . . . . . . . .HOPPER SUPPORT BAR 18. . . . . . . . . . .

HOW THE MACHINE WORKS 19. . . . . . . . . .PRE-OPERATION CHECKLIST 19. . . . . . . . .

CHANGING AN LPG FUEL TANK 20. . . .STARTING THE MACHINE 22. . . . . . . . . . . . .OPERATION ON INCLINES 24. . . . . . . . . . . .SWEEPING AND BRUSH INFORMATION 25SWEEPING 26. . . . . . . . . . . . . . . . . . . . . . . . . .STOP SWEEPING 28. . . . . . . . . . . . . . . . . . . .EMPTYING THE HOPPER 29. . . . . . . . . . . . .STOPPING THE MACHINE 31. . . . . . . . . . . .POST-OPERATION CHECKLIST 32. . . . . . . .ENGAGING HOPPER SUPPORT BAR 33. .DISENGAGING HOPPER SUPPORT BAR 35OPTIONS 37. . . . . . . . . . . . . . . . . . . . . . . . . . . .

QUICK MOP 37. . . . . . . . . . . . . . . . . . . . . . .MACHINE TROUBLESHOOTING 39. . . . . . .

MAINTENANCE 40. . . . . . . . . . . . . . . . . . . . . . . . .MAINTENANCE CHART 40. . . . . . . . . . . . . . .LUBRICATION 42. . . . . . . . . . . . . . . . . . . . . . . .

ENGINE 42. . . . . . . . . . . . . . . . . . . . . . . . . . .STEERING GEAR CHAIN 42. . . . . . . . . . .STEERING CASTOR PIVOT BEARING 43

PageHYDRAULICS 44. . . . . . . . . . . . . . . . . . . . . . . .

HYDRAULIC FLUID RESERVOIRS 44. . .HYDRAULIC FLUID 46. . . . . . . . . . . . . . . .HYDRAULIC HOSES 47. . . . . . . . . . . . . . .

ENGINE 47. . . . . . . . . . . . . . . . . . . . . . . . . . . . .AIR FILTER 47. . . . . . . . . . . . . . . . . . . . . . . .FUEL LINES 48. . . . . . . . . . . . . . . . . . . . . . .CARBURETOR 49. . . . . . . . . . . . . . . . . . . .SPARK PLUGS 49. . . . . . . . . . . . . . . . . . . .BATTERY 49. . . . . . . . . . . . . . . . . . . . . . . . .

BELTS AND CHAINS 50. . . . . . . . . . . . . . . . . .VACUUM FAN BELT 50. . . . . . . . . . . . . . . .MAIN BRUSH BELT 50. . . . . . . . . . . . . . . .HYDRAULIC PUMP BELT 51. . . . . . . . . . .JACKSHAFT BELT 51. . . . . . . . . . . . . . . . .STEERING GEAR CHAIN 52. . . . . . . . . . .STATIC DRAG CHAIN 52. . . . . . . . . . . . . .

DEBRIS HOPPER 53. . . . . . . . . . . . . . . . . . . . .HOPPER DUST FILTER 53. . . . . . . . . . . . .

REMOVING HOPPER DUSTFILTER 54. . . . . . . . . . . . . . . . . . . . . .

THERMO SENTRY 57. . . . . . . . . . . . . . . . .BRUSHES 58. . . . . . . . . . . . . . . . . . . . . . . . . . . .

MAIN BRUSH 58. . . . . . . . . . . . . . . . . . . . . .REPLACING MAIN BRUSH 58. . . . . . .CHECKING AND ADJUSTING MAIN

BRUSH PATTERN 59. . . . . . . . . . . .SIDE BRUSH 61. . . . . . . . . . . . . . . . . . . . . .

REPLACING SIDE BRUSH 62. . . . . . .SIDE BRUSH GUARD 62. . . . . . . . . . . . . .

SKIRTS AND SEALS 63. . . . . . . . . . . . . . . . . .SIDE SKIRTS 63. . . . . . . . . . . . . . . . . . . . . .LARGE DEBRIS TRAP SKIRT 63. . . . . . .SIDE RECIRCULATION SKIRTS 63. . . . .REAR SKIRTS 64. . . . . . . . . . . . . . . . . . . . .HOPPER SEALS 65. . . . . . . . . . . . . . . . . . .HOPPER DOOR SEAL 65. . . . . . . . . . . . . .HOPPER LIP SEAL 65. . . . . . . . . . . . . . . . .VACUUM SEAL 66. . . . . . . . . . . . . . . . . . . .HOPPER FILTER SEALS 66. . . . . . . . . . . .AIR INTAKE SEAL 66. . . . . . . . . . . . . . . . . .

BRAKES AND TIRES 67. . . . . . . . . . . . . . . . . .BRAKES 67. . . . . . . . . . . . . . . . . . . . . . . . . .TIRES 68. . . . . . . . . . . . . . . . . . . . . . . . . . . .

PUSHING, TOWING, AND TRANSPORTINGTHE MACHINE 69. . . . . . . . . . . . . . . . . . . . .PUSHING OR TOWING THE MACHINE 69TRANSPORTING THE MACHINE 69. . . .

MACHINE JACKING 71. . . . . . . . . . . . . . . . . . .STORING MACHINE 71. . . . . . . . . . . . . . . . . .

SPECIFICATIONS 72. . . . . . . . . . . . . . . . . . . . . . .GENERAL MACHINE

DIMENSIONS/CAPACITIES 72. . . . . . . . .GENERAL MACHINE PERFORMANCE 72. .POWER TYPE 73. . . . . . . . . . . . . . . . . . . . . . . .STEERING 73. . . . . . . . . . . . . . . . . . . . . . . . . . .HYDRAULIC SYSTEMS 73. . . . . . . . . . . . . . . .BRAKING SYSTEM 73. . . . . . . . . . . . . . . . . . .TIRES 73. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .MACHINE DIMENSIONS 74. . . . . . . . . . . . . . .

SAFETY PRECAUTIONS

6200 Gas/LPG 330379 (4--2012)2

SAFETY PRECAUTIONS

The following symbols are used throughout thismanual as indicated in their description:

WARNING: To warn of hazards or unsafepractices that could result in severepersonal injury or death.

FOR SAFETY: To identify actions thatmust be followed for safe operation ofequipment.

The machine is suited to sweep disposable debris.Do not use the machine other than described inthis Operator Manual. The machine is notdesigned for use on public roads.

The following information signals potentiallydangerous conditions to the operator orequipment:

WARNING: Engine emits toxic gases.Severe respiratory damage orasphyxiation can result. Provideadequate ventilation. Consult with yourregulatory authorities for exposurelimits. Keep engine properly tuned.

WARNING: Lift arm pinch point. Stayclear of hopper lift arms.

WARNING: Raised hopper may fall.Engage hopper support bar.

FOR SAFETY:

1. Do not operate machine:-- Unless trained and authorized.-- Unless operation manual is read andunderstood.

-- Unless mentally and physicallycapable of following machineinstructions.

-- In flammable or explosive areas unlessdesigned for use in those areas.

-- In areas with possible falling objectsunless equipped with overhead guard.

2. Before starting machine:-- Check for fuel leaks.-- Keep sparks and open flame awayfrom refueling area.

-- Make sure all safety devices are inplace and operate properly.

-- Check brakes and steering for properoperation.

3. When starting machine:-- Keep foot on brake and directionalpedal in neutral.

4. When using machine:-- Do not pickup up burning or smokingdebris, such as cigerettes, matches orhot ashes.

-- Use brakes to stop machine.-- Go slowly on inclines and slipperysurfaces.

-- Use care when reversing machine.-- Do not carry riders on machine.-- Always follow safety and traffic rules.-- Report machine damage or faultyoperation immediately.

5. Before leaving or servicing machine:-- Stop on level surface.-- Set parking brake.-- Turn off machine and remove key.

6. When servicing machine:-- Avoid moving parts. Do not wear loosejackets, shirts, or sleeves whenworking on machine.

-- Block machine tires before jacking upmachine.

-- Jack up machine at designatedlocations only. Block machine up withjack stands.

-- Use hoist or jack that will support theweight of the machine.

-- Wear eye and ear protection if usingpressurized air or water.

-- Disconnect battery connections beforeworking on machine.

-- Avoid contact with battery acid.-- Use cardboard to locate leakinghydraulic fluid under pressure.

-- Use Tennant supplied or equivalentreplacement parts.

7. When loading/unloading machineonto/off truck or trailer:-- Turn off machine.-- Use truck or trailer that will supportthe weight of the machine.

-- Use winch. Do not drive the machineonto/off the truck or trailer unless theload height is 380 mm (15 in) or lessfrom the ground.

-- Set parking brake after machine isloaded.

-- Block machine tires.-- Tie machine down to truck or trailer.

SAFETY PRECAUTIONS

36200 Gas/LPG 330379 (9--1999)

The following safety labels are mounted on themachine in the locations indicated. If these or anylabels become damaged or illegible, install a newlabel in its place.

FOR SAFETY LABEL -- LOCATED ON THESIDE OF THE OPERATOR COMPARTMENT.

HOPPER LIFT ARMS LABEL --LOCATED ON BOTH LIFT ARMS.

EMISSIONS LABEL -- LOCATEDBEHIND THE OPERATOR’S SEAT.

352944

HOPPER SUPPORT LABEL -- LOCATED ONLEFT SIDE HOPPER LIFT ARM AND BOTHSIDES OF THE HOPPER COMPARTMENT.

OPERATION

6200 Gas/LPG 330379(9--2002)4

OPERATION

OPERATOR RESPONSIBILITY

- The operator’s responsibility is to take careof the daily maintenance and checkups ofthe machine to keep it in good workingcondition. The operator must inform theservice mechanic or supervisor when themaintenance intervals are required as statedin the MAINTENANCE section of thismanual.

- Read this manual carefully before operatingthe machine.

FOR SAFETY: Do not operate machine,unless operation manual is read andunderstood.

- Check the machine for shipping damage.Check to make sure the machine iscomplete per shipping instructions.

- Keep your machine regularly maintained byfollowing the maintenance information in thismanual. We recommend taking advantage ofa regularly scheduled service contract fromyour Tennant representative.

- Order parts and supplies directly from yourauthorized Tennant representative. Use theparts manual provided when ordering parts.

- After operation, follow the recommendeddaily and hourly procedures stated in theMAINTENANCE CHART.

07324

OPERATION

56200 Gas/LPG 330379(6--2007)

MACHINE COMPONENTS

BC

D

E

G

F

A

H

A. Operator seatB. Steering wheelC. Instrument panelD. Side brushE. Control pedalsF. HopperG. Hopper filterH. Fuel tank

OPERATION

6200 Gas/LPG 330379(2--2010)6

SYMBOL DEFINITIONS

These symbols identify controls, displays, andfeatures on the machine:

On Voltmeter

Off Filter shaker

Start Operating lights

Vacuum Fan Hazard light

Circuit breaker #1 Hopper lift

Circuit breaker #2 Hopper lower

Circuit breaker #3 Open hopper

Circuit breaker #4 Close hopper

Circuit breaker #5 Main brush down

Circuit breaker #6 Main brush up

Circuit breaker #7 Side brush down and on

Circuit breaker #8 Side brush up and off

Circuit breaker #9 Horn

Choke Unleaded fuel only

OPERATION

76200 Gas/LPG 330379(3--2006)

CONTROLS AND INSTRUMENTS

A B CD E

G

F

HJ

K

LO MQ

P

I

R

N

A. Side brush leverB. Ignition switchC. HornD. Charging system lightE. HourmeterF. Fuel level gaugeG. Steering wheelH. Main brush leverI. Directional pedalJ. Brake pedalK. Parking brake pedalL. Vacuum fan/filter shaker switchM. Hopper door switchN. Low oil warning indicatorO. Hopper switchP. Operating/Hazard lights switch (option)Q. Large debris trap pedalR. Engine choke knob

OPERATION

6200 Gas/LPG 330379(6--1999)8

OPERATION OF CONTROLS

DIRECTIONAL PEDAL

The directional pedal controls the direction oftravel and the propelling speed of the machine.Change the speed of the machine with thepressure of your foot on the pedal; the harder youpress the faster the machine travels.

Use the brake pedal to stop the machine.

Forward: Press the top of the directional pedalwith the toe of your foot.

Note: The machine will not travel unless theoperator is sitting in the operator’s seat.

Reverse: Press the bottom of the directional pedalwith the heel of your foot.

Neutral: Take your foot off the directional pedaland it will return to the Neutral position.

OPERATION

96200 Gas/LPG 330379(6--1999)

BRAKE PEDAL

The brake pedal stops the machine.

Stop: Remove your foot from the directional pedaland let it return to the Neutral position. Step onthe brake pedal to prevent the machine fromrolling.

PARKING BRAKE PEDAL

The parking brake pedal sets and releases thefront wheel brake.

Set: Hold the brake pedal with the right foot. Presson the parking brake pedal with the left foot to lockthe parking brake pedal in place.

FOR SAFETY: Before leaving orservicing machine, stop on levelsurface, set parking brake, turn offmachine, and remove key.

Release: Press down on the brake pedal until theparking brake releases.

LARGE DEBRIS TRAP PEDAL

The large debris trap pedal opens the large debrisflap in front of the main sweeping brush.

Open: Press on the trap pedal when sweeping uplarger debris. The flap in front of the mainsweeping brush will open to take in large debris.

Close: Release the pedal and the flap will close,trapping larger debris into the hopper.

OPERATION

6200 Gas/LPG 330379(6--1999)10

IGNITION SWITCH

The ignition switch controls machine power andmain sweeping brush with a key.

Start: Turn the key all the way clockwise, andrelease the key as soon as the engine starts. Thevacuum fan and main brush both operate whilethe engine is running.

FOR SAFETY: When starting machine,keep foot on brake and directional pedalin neutral.

Stop: Turn the key counterclockwise.

HORN BUTTON

The horn button operates the horn.

Sound: Press the button.

SIDE BRUSH LEVER

The side brush lever controls the position and thepower of the side brush.

Side brush down and on: Pull the lever left andforward into the Side brush down and onposition. The brush will automatically startrotating.

Side brush up and off: Pull the lever back and tothe right into the Side brush up and off position.

OPERATION

116200 Gas/LPG 330379(6--1999)

OPERATING LIGHTS SWITCH (OPTION)

The operating lights switch powers on and off theheadlights and taillights option.

On: Press the top of the operating lights switch.

Off: Press the switch to the middle position.

OPERATING/HAZARD LIGHTS SWITCH(OPTION)

The operating/hazard lights switch powers on andoff the headlights and taillights option and thehazard light option.

Operating lights on: Press the top of theoperating/hazard lights switch.

Operating/Hazard lights on: Press the bottom ofthe operating/hazard lights switch.

Off: Press the operating/hazard lights switch in themiddle position.

OPERATION

6200 Gas/LPG 330379(3--2006)12

MAIN BRUSH LEVER

The main brush lever controls the position of themain brush.

Main brush down: Pull the lever to the right andback into the Main brush down position.

Main brush up: Push the lever up and to the leftinto the Main brush up position.

CHARGING SYSTEM LIGHT

The charging system light comes on when thealternator is not operating within the normal range;13.5 to 14.5 V. If the light comes on, stopoperating the machine. Locate the problem andhave it corrected.

LOW OIL WARNING INDICATOR

The low oil warning indicator will illuminate whenthe engine oil level drops below a certain level.When the engine oil level is too low, the enginewill automatically shut itself off.

The engine will not restart and the indicator willnot go out until the proper amount of engine oilhas been added.

OPERATION

136200 Gas/LPG 330379(9--2005)

FUEL LEVEL GAUGE

The LPG fuel level gauge is located on the top ofthe fuel tank. It indicates how much fuel is left inthe fuel tank.

The fuel level gauge for gasoline poweredmachines serial number 6200130 xxx and above,is located on the instrument panel. It indicateshow much fuel is left in the fuel tank.

NOTE: Do not use leaded fuels. The use ofleaded fuels will cause permanent damage to thesystem’s oxygen sensor and catalytic converter.

Gasoline powered machines below serial number6200130 xxx do not have a fuel level gauge.Check the fuel level by looking into the fuel tank.

GASOLINE ENGINE CHOKE KNOB

The engine choke knob controls the engine chokeon gasoline powered machines.

On: For cold starting, pull the engine choke knobout.

Off: Push the engine choke knob in.

OPERATION

6200 Gas/LPG 330379(6--1999)14

VACUUM FAN/FILTER SHAKER SWITCH

The vacuum fan/filter shaker switch controls boththe vacuum fan damper and the VCS VibratingComb Shaker. The vacuum fan damper should beopen when sweeping dry debris, and closed whensweeping wet debris.

Vacuum fan damper open: Press the top of theswitch to the vacuum fan damper open positionfor dry sweeping.

Vacuum fan damper closed: Press the switch tothe middle vacuum fan damper closed positionfor wet sweeping.

Start filter shaker: Press and hold the bottom ofthe switch for eight to ten seconds.

Note: Excessive heat in the hopper will cause theThermo Sentry to close the vacuum fan damper. Ifthis happens, stop the machine, eliminate thesource of heat, and reset the switch to thevacuum fan damper open position.

STEERING WHEEL

The steering wheel controls the machine’sdirection. The machine is very responsive to thesteering wheel movements.

Left: Turn the steering wheel to the left.

Right: Turn the steering wheel to the right.

HOURMETER

The hourmeter records the number of hours themachine has been operated. The hourmeterdisplays the number of hours in tenths of an hour.Use this information to determine machinemaintenance intervals.

OPERATION

156200 Gas/LPG 330379(6--1999)

HOPPER SWITCH

The hopper switch raises and lowers the hopper.

Raise hopper: Press and hold the top of theswitch until the hopper is in the desired raisedposition.

Hold: Release the hopper switch into the middleposition.

Lower hopper: Press and hold the bottom of theswitch until the hopper is in the desired loweredposition.

HOPPER DOOR SWITCH

The hopper door switch opens and closes thehopper door.

Open hopper door: Press and hold the top of theswitch until the door is in the desired openposition.

Hold: Release the hopper door switch into themiddle position.

Close hopper door: Press and hold the bottom ofthe switch until the door is in the desired closedposition.

OPERATION

6200 Gas/LPG 330379(9--1999)16

CIRCUIT BREAKERS

The circuit breakers are resettable electrical circuitprotection devices. Their design stops the flow ofcurrent in the event of a circuit overload. Once acircuit breaker is tripped, it must be resetmanually. Press the reset button after the breakerhas cooled down. The circuit breakers will notreset until they have had a chance to cool down.

If the overload that caused the circuit breaker totrip is still there, the circuit breaker will continue tostop current flow until the problem is corrected.

Circuit breakers 1 through 7 are located above thefoot pedals in the circuit breaker panel.

The chart lists the circuit breakers and theelectrical components they protect.

Circuit Breaker Rating Circuit Protected

CB-1 15 A Horn, Reverse,Back up alarm opt.

CB-2 15 A Filter shaker

CB-3 15 A Side brush(es)

CB-4 40 A Hopper lift motor

CB-5 15 A Main

CB-6 15 A Hopper door

CB-7 15 A Headlight, TaillightWarning light opt.

1 3

4

5 7

26

OPERATION

176200 Gas/LPG 330379(6--1999)

OPERATOR SEAT

The operator seat is a fixed back style.

ADJUSTABLE OPERATOR SEAT (OPTION)

The adjustable operator seat is a fixed back stylewith a forward--backward adjustment.

Adjust: Pull the lever in, slide the seat backward orforward to the desired position, and release thelever.

DELUXE SUSPENSION SEAT (OPTION)

The deluxe suspension seat has four adjustments.The adjustments are for the lumbar support,backrest angle, operator weight adjustment andfront to back adjustment.

The lumbar adjustment knob controls the firmnessof the lumbar support.

Increase firmness: Turn knob clockwise.

Decrease firmness: Turn knob counterclockwise.

The backrest angle knob adjusts the angle of thebackrest.

Increase angle: Turn the angle adjustment knobcounterclockwise.

Decrease angle: Turn the angle adjustment knobclockwise.

OPERATION

6200 Gas/LPG 330379(6--1999)18

The weight adjustment knob controls the firmnessof the operator’s seat.

Increase firmness: Turn the weight adjustmentknob clockwise.

Decrease firmness: Turn the weight adjustmentknob counterclockwise.

Use the gauge next to the weight adjustment knobto help determine proper seat firmness for theoperator.

The front--to--back adjustment lever adjusts theseat position.

Adjust: Pull the lever out and slide the seatforward or backward to the desired position.Release the lever.

HOPPER SUPPORT BAR

The hopper support bar is located on the hydrauliccylinder. It is manually moved into place when thecylinder is fully extended to prevent the hopperfrom lowering. Lift it off the cylinder beforelowering the hopper.

WARNING: Raised hopper may fall.Engage hopper support bar

OPERATION

196200 Gas/LPG 330379(6--1999)

HOW THE MACHINE WORKS

The steering wheel controls the direction ofmachine travel. The directional pedal controls thespeed and forward/reverse direction. The brakepedal slows and stops the machine.

The side brush sweeps debris into the path of themain sweeping brush. The main brush sweepsdebris from the floor into the hopper. The largedebris trap pedal opens and closes the largedebris trap, kicking large debris into the hopper.The vacuum system pulls dust and air into thehopper through the Instant Access filter.

When sweeping is finished, clean the InstantAccess filter and empty the hopper.

PRE-OPERATION CHECKLIST

- Check the engine oil level.

- Check the hydraulic fluid level

- Check the air filter indicator.

- Check the skirts and seals for damage andwear.

- Check the condition of the sweepingbrushes. Remove any string, banding, plasticwrap, or other debris wrappedaround them.

- Check the sweeping brush patterns foradjustment.

- Check the condition of the hopper dust filterand seals. Clean as required.

- Check the brakes and steering for properoperation.

- Check the fuel level

- Empty the debris hopper.

- Check the service records to determinemaintenance requirements.

OPERATION

6200 Gas/LPG 330379(1--2000)20

CHANGING AN LPG FUEL TANK

1. Park the machine in a designated safe area.

2. Close the tank service valve on the LPGtank located under the operator seat.

3. Operate the engine until it stops from lack offuel, then set the machine parking brake.

FOR SAFETY: When servicing machine,keep flames and sparks away from fuelsystem service area. Keep area wellventilated.

4. Put on gloves and remove thequick-disconnect tank coupling.

5. Unlatch and remove the empty LPG fueltank from the machine and store the tank ina designated, safe area.

6. Carefully put the filled LPG tank in themachine so that the tank centering pinenters the aligning hole in the tank collar.

NOTE: Make sure the LPG fuel tank matches thefuel system (vapor tank with vapor system).

7. Fasten the tank hold-down clamp to lock thetank in position.

OPERATION

216200 Gas/LPG 330379(1--2000)

8. Connect the LPG fuel line to the tank’s vaporservice coupling. Make sure the servicecoupling is clean and free of damage. Alsomake sure it matches the machine servicecoupling.

9. Open the tank service valve slowly andcheck for leaks. Close the service valveimmediately if an LPG leak is found, and tellthe appropriate personnel.

OPERATION

6200 Gas/LPG 330379(1--2000)22

STARTING THE MACHINE

1. LPG powered machines: Open the vaporservice valve slowly.

NOTE: Opening the service valve too quickly maycause the service check valve to stop the flow ofLPG fuel. If the check valve stops the fuel flow,close the service valve, wait a few seconds andopen the valve slowly again.

2. Sit in the operator’s seat and engage thebrakes with the directional pedal in neutral.


3. Pull out the choke knob for the gasolineengine when the engine is cold. Push in thechoke knob after the engine is runningsmoothly.

OPERATION

236200 Gas/LPG 330379(6--1999)

4. Turn the ignition switch key clockwise untilthe engine starts.

NOTE: Do not operate the starter motor for morethan 10 seconds at a time or after the engine hasstarted. Allow the starter to cool between startingattempts or damage to the starter motor mayoccur.

5. Allow the engine to warm up two to threeminutes.

WARNING: Engine emits toxic gases.Severe respiratory damage orasphyxiation can result. Provideadequate ventilation. Consult with yourregulatory authorities for exposurelimits. Keep engine properly tuned.

6. Release the machine parking brake.

7. Drive the machine to the area to be cleaned.

OPERATION

6200 Gas/LPG 330379(6--1999)24

OPERATION ON INCLINES

Drive the machine slowly on inclines. Use thebrake pedal to control machine speed whendescending inclines.

The maximum rated incline is 6_/11% with a fullhopper and 10_/18% with an empty hopper.

FOR SAFETY: When using machine, goslowly on inclines and slipperysurfaces.

OPERATION

256200 Gas/LPG 330379(9--2001)

SWEEPING AND BRUSH INFORMATION

Pick up oversized debris before sweeping. Flattenor remove bulky cartons from aisles beforesweeping. Pick up pieces of wire, twine, string,etc., which could become entangled in the brushor brush plugs.

Plan the sweeping in advance. Try to arrange longruns with minimum stopping and starting. Do anentire floor or section at one time. Drive thestraightest path possible. Avoid bumping intoposts or scraping the sides of the machine.Overlap the brush paths.

Avoid turning the steering wheel too sharply whenthe machine is in motion. The machine is veryresponsive to the movement of the steering wheel.Avoid sudden turns, except in emergencies.

For best results, use the correct brush type foryour sweeping application. The following arerecommendations for main sweeping and sidebrush applications.

Polypropylene 8-single row main brush --Superior pick-up of sand, gravel, and paper litter.Polypropylene retains its stiffness when wet andcan be used indoors or outdoors with equalperformance. Not recommended forhigh-temperature debris.

Natural Fiber main brush -- The natural choicefor cleaning fine debris on carpet and sweepingvery heavy dust and other fine particles on hardsurfaces. When cleaning carpet, check brush andperma filter panel regularly for carpet debris.

Sand wedge main brush -- A fine brush thathandles large quantities of dust and sand withease.

OPERATION

6200 Gas/LPG 330379(9--2002)26

Side Brush (2 Row) -- A good general purposebrush for sweeping of light to medium debris inboth indoor and outdoor applications. This brush isrecommended when bristles may get wet.

Side Brush (3 Row) -- Improved sweepingperformance of fine materials on smooth indoorsurfaces.

Stiff Side Brush -- A longer life, general purposebrush that is recommended for rough surfaces.

SWEEPING

1. Press the top of the vacuum fan/filter shakerswitch to the vacuum fan damper openposition.

2. Lower the main brush with the main brushlever.

OPERATION

276200 Gas/LPG 330379(6--1999)

3. Lower and start the side brush with the sidebrush lever.

4. Begin sweeping.

5. Press down on the large debris trap pedalwhen sweeping large debris.

6. Release the pedal, and the flap will lowerover the debris.

7. The flap will trap large debris back into thehopper.

OPERATION

6200 Gas/LPG 330379(6--1999)28

STOP SWEEPING

1. Raise and stop the side brush with the sidebrush lever.

2. Raise the main brush with the main brushlever.

3. Activate the filter shaker by pressing downand holding the bottom of the vacuum fan/filter shaker switch for eight to ten seconds.

OPERATION

296200 Gas/LPG 330379(6--1999)

EMPTYING THE HOPPER

1. Stop sweeping. See the STOP SWEEPINGsection of the manual.

2. Drive the machine to the debris site or debriscontainer.

3. Press and hold the top of the hopper switchto raise the hopper to the desired height.Release the switch into the hold position.

FOR SAFETY: When using machine,make sure adequate clearance isavailable before raising hopper.


NOTE: Be aware that the minimum ceiling heightneeded to high dump the hopper is 2286 mm.

4. Back the machine up to the debris container.Position the hopper over the debriscontainer.

FOR SAFETY: When using machine, usecare when reversing machine.

OPERATION

6200 Gas/LPG 330379(6--1999)30

5. Press and hold the top of the hopper doorswitch until the hopper is fully open. Releasethe switch into the hold position.

6. Press and hold the bottom of the hopperdoor switch until the hopper door is fullyclosed.

7. Press and hold the bottom of the hopperswitch until the hopper is fully lowered.


OPERATION

316200 Gas/LPG 330379(6--1999)

STOPPING THE MACHINE

1. Stop sweeping. See the STOP SWEEPINGsection of the manual.

2. Take your foot off the directional pedal. Stepon the brake pedal.

3. Set the machine parking brake.

4. Turn the ignition switch keycounterclockwise to turn the machine poweroff. Remove the switch key


5. LPG powered machines: Close the LPGtank’s vapor service valve.

OPERATION

6200 Gas/LPG 330379(9--2005)32

POST-OPERATION CHECKLIST

Check this list of items after you have finishedsweeping:

- Check the engine oil level.

- Check the hydraulic fluid level

- Check the air filter indicator.

- Check the skirts and seals for damage andwear.

- Check the condition of the sweepingbrushes. Remove any string, banding, plasticwrap, or other debris wrappedaround them.

- Check the sweeping brush patterns foradjustment.

- Check the condition of the hopper dust filterand seals. Clean as required.

- Check the brakes and steering for properoperation.

- Check the fuel level

- Empty the debris hopper.

- Check the service records to determinemaintenance requirements.

OPERATION

336200 Gas/LPG 330379(6--1999)

ENGAGING HOPPER SUPPORT BAR

1. Set the machine parking brake.


2. Start the machine.

3. Press and hold the top of the hopper switchuntil the hopper is fully raised. Release theswitch into the hold position.


FOR SAFETY: When using machine,make sure adequate clearance isavailable before raising hopper.


OPERATION

6200 Gas/LPG 330379(6--1999)34

4. Push the hopper support bar in place ontothe support cylinder.

WARNING: Raised hopper may fall.Engage hopper support bar

5. Slowly lower the hopper by pressing downand holding the hopper switch until thehopper support bar rests on the support barstop.


6. Turn the machine power off.

OPERATION

356200 Gas/LPG 330379(6--1999)

DISENGAGING HOPPER SUPPORT BAR

1. Start the machine.

2. Raise the hopper slightly by pressing up andholding the hopper switch. Release theswitch into the hold position.


3. Move the hopper support bar off the cylinderinto the storage position.


OPERATION

6200 Gas/LPG 330379(6--1999)36

4. Press and hold the bottom of the hopperswitch until the hopper is in the fully loweredposition.


5. Turn the machine power off.

OPERATION

376200 Gas/LPG 330379(1--2000)

OPTIONS

QUICK MOP

The QuickMop is a front end sweeping attachmentthat widens the machine’s sweeping path.

1. Drive the machine close to QuickMopattachment.

2. Set the machine parking brake and turn themachine power off.


3. Connect the QuickMop attachment to themounting bracket on the front of themachine.

4. Fasten the latches on the front of themounting bracket. Release the parking brakeand drive to the designated area to beswept.

OPERATION

6200 Gas/LPG 330379(1--2000)38

5. Pull the release lever to raise or lower eachside of the QuickMop.

6. Turn the vacuum and brushes on, lowerbrushes and begin sweeping.

7. Remove and refasten the QuickMop headcovers with the easy to remove snaps.Remove the head covers to rotate, shakeand clean at regular intervals.

OPERATION

396200 Gas/LPG 330379(1--2000)

MACHINE TROUBLESHOOTING

Problem Cause Remedy

Excessive dusting Vacuum fan damper closed Press the vacuum fan / filtershaker switch to the on position

Brush skirts and dust seals worn,damaged, out of adjustment

Replace or adjust brush skirts ordust seals

Hopper dust filter clogged Shake and/or clean or replacedust filter

Hopper full Empty hopper

Vacuum fan failure Contact Tennant service person-nel

Hopper not fully lowered Lower hopper

Poor sweeping performance Brush bristles worn Replace brushes

Main and side brushes notadjusted properly

Adjust main and side brushes

Debris caught in main brush drivemechanism

Remove debris from drivemechanism

Main brush drive failure Contact Tennant servicepersonnel

Side brush drive failure Contact Tennant servicepersonnel

Hopper full Empty hopper

Hopper lip skirts worn ordamaged

Replace lip skirts

Wrong sweeping brush Contact Tennant representativefor recommendations

Large debris trap damaged Repair or replace large debris trap

Hopper dust filter clogged Shake and/or clean or replacedust filter

Machine will not start Engine oil level low Check and fill

Fuel tank valve closed Open valve -- LPG tank valve orvalve beneath gasoline tank

Fuel tank empty Fill fuel tank

MAINTENANCE

6200 Gaas/LPG 330379(9--2005)40

MAINTENANCE

13

13

12

14 7

2

1415

1 2

2

7

4

5

6891011 27

3

3

MAINTENANCE CHART

NOTE: Check procedures indicated (H) after the first 50 hours of operation.

Interval Key Description ProcedureLubricant/

Fluid

No. ofServicePoints

Daily 1 Engine Check oil level EO 1

Check air intake and coolingareas for debris

-- 1

2 Brush compartment skirts Check for damage, wear andadjustment

-- 5

3 Side skirts Check for damage, wear andadjustment

-- 2

9 Main brush Check for damage, wear andadjustment

-- 1

6 Side brush(es) Check for damage, wear andadjustment

-- 1 (2)

Check brush pattern -- 1 (2)

13 Hopper dust filter Shake -- 1

25 Hours 1 Engine Clean and re--oil air filterpre cleaner element

-- 1

50 Hours 9 Main brush Rotate end-for-end -- 1

Check brush pattern -- 1

1 Fuel lines Check for damage and wear -- All

-- QuickMop broom (Option) Rotate or wash sweep heads -- 2

MAINTENANCE

416200 Gas/LPG 330379(2--2010)

Interval Key Description ProcedureLubricant/

Fluid

No. ofServicePoints

100 Hours 1 Engine Change oil EO 1

Clean or replace spark plugs -- 1

Replace air filter element -- 1

Clean air intake screen andshrouds

-- 1

13 Hopper dust filter Check for damage, clean orreplace

-- 1

7 Tires Check for damage or wear -- 3

4 Steering castor pivotbearing

Lubricate SPL 1

13 Hopper seals Check for damage or wear -- 6

13 Hopper filter seals Check for damage or wear -- 2

13 Vacuum seal Check for damage or wear -- 1

1 Air intake seal Check for damage or wear -- 1

11 Vacuum fan belt Check tension and wear -- 1

10 Main brush belt Check tension and wear -- 1

14 Hydraulic pump belt Check tension and wear -- 1

15 Jackshaft belt Check tension and wear -- 1

14 Hydraulic fluid reservoirs Check fluid levels -- 2

200 Hours 5 Brake Check adjustment -- 1

4 Steering gear chain Lubricate EO 1

6 Side brush(es) guard Check for damage or wear -- 1 (2)

800 Hours 14 Hydraulic hoses Check for wear and damage -- All

14 Main hydraulic reservoircap

Replace cap -- 1

7 Wheels Check rear wheel axle torque -- 2

8 Battery HClean and tighten battery cableconnections

-- 2

1200Hours

14 Hydraulic fluid filter * Change filter element -- All

2400Hours

14 Hydraulic fluid reservoir * Replace suction strainer -- 1* Change hydraulic fluid HYDO 2

NOTE: Change the hydraulic fluid, filter, and suction strainer, indicated (*), after every 800 hours formachines NOT originally equipped with TennantTrue premium hydraulic fluid. (See Hydraulics section).LUBRICANT/FLUIDEO Engine oil, SAE 10W--30, CD/CE rated. . . .HYDO TennantTrue premium hydraulic fluid or equivalent.SPL Special lubricant, Lubriplate EMB grease (TENNANT part no. 01433--1). . .

NOTE: More frequent intervals may be required in extremely dusty conditions.

MAINTENANCE

6200 Gaas/LPG 330379(9--2002)42

LUBRICATION

ENGINE

Check the engine oil level daily. Change theengine oil after every 100 hours of operation. Use30 SAE SG/SH rated engine oil.

Fill the engine with oil to the level indicated on theoil dipstick. The engine oil capacity is 1.2 L.

STEERING GEAR CHAIN

The steering chain turns the front wheel as thesteering wheel is turned to steer the machine.Lubricate the steering chain with 30 SAE engineoil after every 200 hours of operation.

MAINTENANCE

436200 Gas/LPG 330379(1--2000)

STEERING CASTOR PIVOT BEARING

The steering castor bearing is located under thefloor plate. Remove the floor plate, and lubricatethe bearing every 100 hours with Lubriplate EMBgrease (TENNANT part no. 01433--1).

MAINTENANCE

6200 Gaas/LPG 330379(2--2010)44

HYDRAULICS

HYDRAULIC FLUID RESERVOIRS

The 6200 has two hydraulic fluid reservoirs, themain hydraulic reservoir and the hopper liftreservoir.

The main hydraulic reservoir is located in theengine compartment.

A filler cap is mounted on top of the mainreservoir. It has a built-in breather and fluid leveldipstick. Lubricate the filler cap gasket with a filmof hydraulic fluid before putting the cap back onthe reservoir. Replace the cap after every 800hours of operation.

Check the hydraulic fluid level of the mainreservoir at operating temperature after every 100hours of operation. The end of the dipstick ismarked with FULL and ADD levels to indicate thelevel of hydraulic fluid in the reservoir.

ATTENTION! Do not overfill thehydraulic fluid reservoir or operate themachine with a low level of hydraulicfluid in the reservoir. Damage to themachine hydraulic system may result.

Drain and refill the hydraulic fluid reservoir withnew TennantTrue premium hydraulic fluid afterevery 2400 hours of operation. Machines have ablue colored drop (left photo) on the hydraulic fluidlabel if originally equipped with TennantTruepremium hydraulic fluid.

TennantTrue Fluid Previous Fluid

NOTE: Change the hydraulic fluid, filter, andsuction strainer after every 800 hours for ALLmachines that have NOT consistently usedTennantTrue premium hydraulic fluid orequivalent.

The main hydraulic reservoir has a built-in straineroutlet that filters hydraulic fluid before it enters thesystem. Replace the strainer after every 2400hours of operation.

MAINTENANCE

456200 Gas/LPG 330379(2--2010)

The hydraulic fluid filter is located in the enginecompartment next to the hydraulic reservoir.Replace the filter element after every 1200 hoursof operation.

The hydraulic hopper lift reservoir is locatedbehind the hopper compartment.

A filler cap is mounted on top of the reservoir. It isnot a breather cap, and requires no regularmaintenance.

Check the hydraulic fluid level of the hopper liftreservoir at operating temperature after every 100hours of operation. Make sure the hopper supportbar is in place before checking hydraulic fluidlevel. The side of the reservoir is marked withFULL and ADD levels to indicate the level ofhydraulic fluid in the reservoir.



MAINTENANCE

6200 Gaas/LPG 330379(2--2010)46

HYDRAULIC FLUID

The quality and condition of the hydraulic fluid playa very important role in how well the machineoperates. Tennant’s hydraulic fluid is speciallyselected to meet the needs of Tennant machines.

Tennant’s hydraulic fluids provide a longer life forthe hydraulic components. There are two fluidsavailable for different temperature ranges:

TennantTrue premiumhydraulic fluid (Extended Life)

Partnumber

Ambienttemperature

ISOGrade

Ca-pacity

1057710 above 7_ C (45_ F) 100 3.8 L(1 gal)

1057711 above 7_ C (45_ F) 100 19 L(5 gal)

1057707 below 7_ C (45_ F) 32 3.8 L(1 gal)

1057708 below 7_ C (45_ F) 32 19 L(5 gal)

The higher temperature fluid has a higher viscosityand should not be used at the lower temperatures.Damage to the hydraulic pumps may occurbecause of improper lubrication.

The lower temperature fluid is a thinner fluid forcolder temperatures. This fluid should be used forthe hydraulic lift cylinder at all times.

If a locally available hydraulic fluid is used, makesure the specifications match Tennant hydraulicfluid specifications. Using substitute fluids cancause premature failure of hydraulic components.

ATTENTION! Hydraulic componentsdepend on system hydraulic fluid forinternal lubrication. Malfunctions,accelerated wear, and damage will resultif dirt or other contaminants enter thehydraulic system.

MAINTENANCE

476200 Gas/LPG 330379(2--2010)

HYDRAULIC HOSES

Check the hydraulic hoses after every 800 hoursof operation for wear or damage.

Fluid escaping at high pressure from a very smallhole can be almost invisible, and can causeserious injuries.

See a doctor at once if injury results fromescaping hydraulic fluid. Serious infection orreaction can develop if proper medical treatment isnot given immediately.

FOR SAFETY: When servicing machine,use cardboard to locate leakinghydraulic fluid under pressure.

If you discover a fluid leak, contact your mechanicor supervisor.

ENGINE

Maintaining cooling system efficiency is important.Engine temperatures must be brought up to andmaintained within the satisfactory range forefficient operation. However, the engine must bekept from overheating in order to prevent damageto the valves, pistons, and bearings. Check the airintake and cooling areas for debris daily, clean ifnecessary.

Clean the intake screen, shrouds and externalsurfaces after every 100 hours of operation.

FOR SAFETY: When servicing machine,wear eye and ear protection if usingpressurized air or water.

AIR FILTER

The engine air filter is made up of two parts, anouter precleaner element and an inner air filterelement. The precleaner element must be cleanedand re--oiled after every 25 hours of operation.The air filter element should be replaced afterevery 100 hours of operation. The air filterelement must be replaced if it is damaged.

To clean the precleaner element, remove the airfilter cover. Remove the precleaner element, washin liquid detergent and water, and squeeze it dry ina cloth. After cleaning the precleaner element,inspect it for damage.

Oil the precleaner element with 30cc of cleanengine oil. Squeeze the precleaner element todistribute the oil evenly throughout the foam.

00002

MAINTENANCE

6200 Gaas/LPG 330379(2--2010)48

Remove the air filter element. Carefully clean thecovers and the interior of the housing with a dampcloth. Clean the housing sealing surfaces. Inspectthe inner air filter element for damage. Theslightest rupture requires replacement of theelement. Inspect the seals on the ends of theelement. They should be flexible and undamaged.

FUEL LINES

Check the fuel lines every 50 hours of operation. Ifany band clamps are loose, apply oil to the screwof the band, and securely tighten the band.

Made of rubber, the fuel lines may become wornout whether the engine has been used much ornot. Replace the fuel lines and hose clamps everytwo years.

FOR SAFETY: When servicing machine,keep flames and sparks away from fuelsystem service area. Keep area wellventilated

If the fuel lines and hose clamps are found wornor damaged before two years’ time, replace orrepair them at once. Bleed the fuel system afterreplacement of any fuel lines. When the fuel linesare not installed, plug both ends with clean clothor paper to prevent dirt from entering the lines.

There is a fuel valve located under the gasolinetank. This valve can be used to shut off the fuelflow if the fuel lines need to be serviced.

MAINTENANCE

496200 Gas/LPG 330379(1--2000)

CARBURETOR

The carburetor is designed to deliver the correctfuel--to--air mixture to the engine under alloperating conditions. The high idle is set at thefactory and cannot be adjusted. The low idle fueladjusting needle is also set at the factory andnormally does not need adjustment.

If the engine is hard--starting, hard starting orstalls at low idle speed, it may be necessary toadjust or service the carburetor.

SPARK PLUGS

Clean or replace and set the gap of the sparkplugs after every 100 hours of operation.

The proper spark plug gap is 0.6 mm.

BATTERY

The battery for the machine is a low maintenancebattery. Do not add water to the battery, or removethe battery vent plugs.

The battery is located in the engine compartment.

After the first 50 hours of operation, and afterevery 800 hours after that, clean and tighten thebattery connections.

FOR SAFETY: When servicing machine,avoid contact with battery acid.

MAINTENANCE

6200 Gaas/LPG 330379(9--2002)50

BELTS AND CHAINS

VACUUM FAN BELT

The vacuum fan belt drives the vacuum system.Check the belt for wear and tension after every100 hours of operation.

The correct tension is when the belt deflects13 mm from a force of 17 kg at belt midpoint.

FOR SAFETY : When servicing machine,avoid moving parts. Do not wear loosejackets, shirts or sleeves when workingon machine.

MAIN BRUSH BELT

The main brush belt drives the main brush. Checkthe main brush belt for wear and tension afterevery 100 hours of operation.

Set the tension with the top sheave.The correcttension on the belt is when the top sheave isputting 6 kg of pressure on the main brush belt.


MAINTENANCE

516200 Gas/LPG 330379(1--2000)

HYDRAULIC PUMP BELT

The hydraulic pump belt drives the hydraulicpump. Check the belt for tension and wear every100 hours of operation.

The correct tension is when the belt deflects4.0 mm from a force of 0.45 kg at belt midpoint ofthe longest span.


JACKSHAFT BELT

The jackshaft belt turns the jackshaft that drivesthe main brush and vacuum fan belts. Check thebelt for tension and wear every 100 hours ofoperation.

The correct tension is when the belt deflects6.0 mm from a force of 0.45 kg at belt midpoint ofthe longest span.


MAINTENANCE

6200 Gaas/LPG 330379(1--2000)52

STEERING GEAR CHAIN

The steering gear chain turns the front wheel asthe steering wheel is turned to steer the machine.Lubricate the steering chain with 30 SAE engineoil after every 200 hours of operation. The chaindoes not need to be checked for tension.

STATIC DRAG CHAIN

A static drag chain prevents the buildup of staticelectricity in the machine. The chain is attached tothe machine by a rear main brush skirt retainingbolt.

Make sure the chain is touching the floor at alltimes.

MAINTENANCE

536200 Gas/LPG 330379(4--2008)

DEBRIS HOPPER

HOPPER DUST FILTER

The hopper filter filters the air pulled up from thehopper. The dust filter is equipped with a shaker toremove the accumulated dust particles. The dustfilter shaker is operated by the main brush,vacuum and filter shaker switch.

Shake the dust filter before emptying the hopperand at the end of every work shift. Check andclean or replace the filter and filter seals afterevery 100 hours of operation.

To clean the dust filter, use one of the followingmethods:

D SHAKING -- Press and hold the main brush,vacuum and filter shaker switch to the Filtershaker position.

D TAPPING -- Remove the filter and tap thefilter gently on a flat surface with the dirtyside down. Do not damage the edges of thefilter element and seals, or the filter will notseat properly in the filter frame.

D AIR -- Always wear eye protection whenusing compressed air. Blow air through thedust filter opposite the direction of thearrows. Never use more than 690 kPa (100psi) of air pressure and never closer than 50mm (2 in) away from the filter. This may bedone with the dust filter in the machine.

FOR SAFETY: When servicing machine,wear eye and ear protection if usingpressurized air or water.

MAINTENANCE

6200 Gaas/LPG 330379(1--2000)54

REMOVING HOPPER DUST FILTER

1. Stop the machine, set the parking brake andturn the machine power off.


2. Unlatch and remove hopper cover.

3. Unplug the filter shaker from the mainharness.

Note: Carefully pull the wires apart from thebodies of the plugs. Do not unplug theconnections from the shaking mechanism. Do notpull on the wires. Damage could occur to the wiresor the shaking mechanism.

4. Lift dust filter assembly out of hopper.

MAINTENANCE

556200 Gas/LPG 330379(1--2000)

5. Lift the VCS system filter shaker off ofthe filter.

6. Clean or discard the Instant Access filter asrequired.

7. Replace the VCS system filter shaker. Usecare to insert the shaking pin into the filtercomb correctly.

8. Place the edges of the shaker firmlybetween the filter and the filter seal.

NOTE: When installed properly, the shaker platecannot move in either front--to--back orside--to--side directions. If the shaker is loose, itwill not function properly.

MAINTENANCE

6200 Gaas/LPG 330379(1--2000)56

9. The filter shaker should lay flat against thefilter. Check to make sure the comb tab isnot caught below the filter shaker plate.

10. Check the shaker solenoid gap with the endof the shipping tab. The gap should be thesame width as the tab. If it is not, loosen themounting screws, adjust the gap byrepositioning the shaker solenoid, thenretighten the screws.

11. Return the filter back to the machine.

MAINTENANCE

576200 Gas/LPG 330379(1--2000)

12. Reconnect the main harness to the shakermechanism.

NOTE: Even if the wires are connected inopposite order of their original positions, theshaker will still function properly.

13. Check the dust filter seals.

14. Replace hopper cover and secure withlatches.

THERMO SENTRY

The Thermo Sentry is located above the debrishopper.

If a fire ignites in the hopper, the Thermo Sentrywill close the vacuum fan damper. The damper willcut off air flow and help extinguish the fire. If thisoccurs, drive the machine to a safe location andeliminate the source of heat. Turn the machine offand back on to reset the Thermo Sentry.

MAINTENANCE

6200 Gaas/LPG 330379(2--2010)58

BRUSHES

MAIN BRUSH

The main brush is cylindrical and spans the widthof the machine, sweeping debris into the hopper.

Check the brush daily for wear or damage.Remove any string or wire tangled on the mainbrush, main brush drive hub, or main brush idlerhub.

Check the main brush pattern every 50 hours ofoperation. The pattern should be 50 to 75 mmwide with the main brush in the lowered position.

Rotate the main brush end-for-end after every 50hours of operation for maximum brush life andbest sweeping performance.

Replace the main brush when it no longer cleanseffectively.

REPLACING MAIN BRUSH



2. Open the left side main brush access door.

3. Loosen the idler arm mounting knob andthree other side skirt mounting knobs.Remove the brush idler arm assembly.

MAINTENANCE

596200 Gas/LPG 330379(1--2000)

4. Grasp the main brush; pull it off the brushdrive plug and out of the main brushcompartment.

5. Put the new or rotated end-for-end mainbrush on the floor next to the access door.

6. Slide the main brush onto the drive plug.Rotate the brush until it engages the driveplug, and push it all the way onto the plug.

7. Check that the recirculation skirt is tucked inbehind the frame.

8. Slide the main brush idler arm plug onto themain brush.

9. Secure the idler arm on the bolts. Handtighten the mounting knobs.

10. Close the main brush access door.

CHECKING AND ADJUSTING MAIN BRUSHPATTERN

1. Apply chalk, or some other material that willnot blow away easily, to a smooth, levelfloor.

2. Raise the side brush and main brush andposition the main brush over the chalkedarea.

3. Start and lower the main brush for 15 to 20seconds while keeping a foot on the brakesto keep the machine from moving.

NOTE: If chalk or other material is not available,allow the brushes to spin on the floor for twominutes. A polish mark will remain on the floor.

4. Raise the main brush.

5. Drive the machine off the test area.

MAINTENANCE

6200 Gaas/LPG 330379(1--2000)60

6. Observe the width of the brush pattern. Theproper brush pattern width is 50 to 75 mm.

The brush taper is factory set and should notneed adjustment unless parts of the brushsystem have been replaced.

If the main brush pattern is tapered, morethan 15 mm on one end than the other,adjust the taper as follows:

1. Loosen the brush shaft bearing bracketmounting bolt and the idler armsecuring head.

2. Allow the brush to operate and float intoposition for approximately 30 seconds.

3. Tighten the adjustment bolt and idlerarm securing knob.

4. Check the main brush pattern andreadjust as necessary.

00582

00601

MAINTENANCE

616200 Gas/LPG 330379(2--2010)

SIDE BRUSH

The side brush sweeps debris along edges intothe path of the main brush.

Check the brush daily for wear or damage.Remove any string or wire found tangled on theside brush or side brush drive hub.

Check the side brush pattern daily. The side brushbristles should contact the floor in a 10 o’clock to 3o’clock pattern when the brush is in motion.

Replace the brush(es) when it no longer cleanseffectively.

Adjust the side brush pattern by loosening the hexscrew located above the side brush pulley. Movethe pulley mount bracket up or down to achievethe proper side brush pattern. Retighten the hexscrew.

350327

MAINTENANCE

6200 Gaas/LPG 330379(1--2000)62

REPLACING SIDE BRUSH



2. Remove the side brush retaining pin fromunder the side brush drive shaft by pullingthe pin keeper off over the end of the pin.

3. Slide the side brush off the side brush driveshaft.

4. Slide the new side brush onto the side brushdrive shaft.

5. Insert the side brush retaining pin throughthe side brush hub and shaft.

6. Secure the pin by clipping the pin keeperover the end of the pin.

SIDE BRUSH GUARD

Check the side brush guard for damage or wearevery 200 hours of operation. Replace the guardwhen it becomes worn.

MAINTENANCE

636200 Gas/LPG 330379(1--2000)

SKIRTS AND SEALS

SIDE SKIRTS

The side skirts are located on both sides of themachine in front of the main brush compartment.The side skirts should clear the floor up to 5 mm.

Check the skirts for damage, wear and adjustmentdaily.

LARGE DEBRIS TRAP SKIRT

The large debris trap skirt is located along thefront of the main brush. This skirt is raised andlowered by the large debris trap pedal, allowinglarger debris to be trapped and swept up into thehopper.

Check the skirt for damage and wear daily.

SIDE RECIRCULATION SKIRTS

The side recirculation skirts are located on bothsides of the main brush compartment. The siderecirculation skirts should clear the floor up to 5mm.


MAINTENANCE

6200 Gaas/LPG 330379(1--2000)64

REAR SKIRTS

The two rear skirts are located on the bottom rearof the main brush compartment. The vertical skirtshould clear the floor up to 5 mm. The rearrecirculation skirt requires no adjustment.


NOTE: The rear recirculation skirt must be foldedin between the brush and the machine framebefore the brush door is mounted for the machineto work properly.

MAINTENANCE

656200 Gas/LPG 330379(1--2000)

HOPPER SEALS

The hopper seals are located around the edge ofthe opening between the main brush and thehopper. The hopper rests against the seals whenthe hopper is in the closed position.

Check the seals for wear or damage after every100 hours of operation.


HOPPER DOOR SEAL

The hopper door seal is located on the bottom ofthe hopper and seals the hopper door when thehopper door is closed.

Check the seal for wear or damage after every100 hours of operation.

HOPPER LIP SEAL

The hopper lip seal is located on the inside of therear lip of the hopper door and seals the inside lipof the hopper door with the hopper


MAINTENANCE

6200 Gaas/LPG 330379(1--2000)66

VACUUM SEAL

The vacuum seal is located behind the debrishopper and seals with the hopper filter cover whenthe hopper is in the lowered position.


HOPPER FILTER SEALS

The hopper filter seals are located along theoutside edge of the top and the bottom of thehopper filter. The hopper filter seals seal thehopper filter in between the hopper baffle plateand the hopper filter cover when the hopper filtercover is latched down in the proper operatingposition.

Check the seals for wear or damage after every100 hours of operation.

AIR INTAKE SEAL

The air intake seal is located along the outer edgeof the air intake baffle and seals with the left sidepanel when the side panel is in place on themachine.


MAINTENANCE

676200 Gas/LPG 330379(1--2000)

BRAKES AND TIRES

BRAKES

The mechanical brake is located on the frontwheel. The brake is operated by the brake footpedal, connecting rods and cable.

Check the brake adjustment after every 200 hoursof operation. If the brake does not respond well topressure on the brake pedal, you may need toadjust the brake.

Adjust the brake cable tension with the cable nutsand the brake lever.

MAINTENANCE

6200 Gaas/LPG 330379(1--2000)68

TIRES

The tires on the machine are solid. Check the tiresafter every 100 hours of operation for damage orwear.

Check the torque on the rear wheel axles every800 hours of operation. The proper torque on rearwheel axle is 22.4--28 Nm.

MAINTENANCE

696200 Gas/LPG 330379(12--2000)

PUSHING, TOWING, AND TRANSPORTINGTHE MACHINE

PUSHING OR TOWING THE MACHINE

If the machine becomes disabled, it can bepushed or towed from the front or rear, but it iseasier and more stable to tow from the front end.

Only push or tow the machine for a very shortdistance and do not exceed 1.6 kp/h (1 mph). It isNOT intended to be pushed or towed a longdistance or at a high speed.

ATTENTION! Do not push or towmachine for a long distance or damagemay occur to the propelling system.

TRANSPORTING THE MACHINE

1. Position the front of the machine at theloading edge of the truck or trailer.

FOR SAFETY: Use truck or trailer thatwill support the weight of the machine.

NOTE: Empty the hopper before transporting themachine.

2. If the loading surface is not horizontal or ishigher than 380 mm (15 in) from the ground,use a winch to load machine.

If the loading surface is horizontal AND is380 mm (15 in) or less from the ground, themachine may be driven onto the truck ortrailer.

3. To winch the machine onto the truck ortrailer, attach the winching chains to the fronttie down located in the front of the machineframe.

FOR SAFETY: When loading machineonto truck or trailer, use winch. Do notdrive the machine onto the truck ortrailer unless the loading surface ishorizontal AND is 380 mm (15 in) or lessfrom the ground.

MAINTENANCE

6200 Gaas/LPG 330379(12--2000)70

4. Position the machine onto the truck or traileras far as possible. If the machine starts toveer off the centerline of the truck or trailer,stop and turn the steering wheel to centerthe machine.

5. Set the parking brake and block the machinetires. Tie down the machine to the truck ortrailer before transporting.

The front tie-down locations are the holes inthe front of the machine frame.

The rear tie-down locations are the holes inthe sides of the machine frame near the rearbumper.

6. If the loading surface is not horizontal or ishigher than 380 mm (15 in) from the ground,use a winch to unload machine.

If the loading surface is horizontal AND is380 mm (15 in) or less from the ground, themachine may be driven off the truck ortrailer.

FOR SAFETY: When unloading machineoff truck or trailer, use winch. Do notdrive the machine off the truck or trailerunless the loading surface is horizontalAND 380 mm (15 in) or less from theground.

MAINTENANCE

716200 Gas/LPG 330379(9--2002)

MACHINE JACKING

Empty the hopper before jacking the machine. Youcan jack up the machine for service at thedesignated locations. Use a hoist or jack that willsupport the weight of the machine. Always stopthe machine on a flat, level surface and block thetires before jacking up the machine.


The front jacking locations are on the flat bottomedge of the front of the machine frame.

The rear jacking locations are on the corners ofthe rear frame.

FOR SAFETY: When servicing machine,block machine tires before jacking upmachine.

FOR SAFETY: When servicing machine,jack up machine at designated locationsonly. Block machine up with jackstands.

STORING MACHINE

Before storing the machine for an extended time,the machine needs to be serviced to lessen thechance of rust, sludge, and other undesirabledeposits from forming.

SPECIFICATIONS

6200 Gas/LPG 330379(2--2010)72

SPECIFICATIONS

GENERAL MACHINE DIMENSIONS/CAPACITIES

Item Dimension/capacity

Length 1955 mm

Width 1070 mm

Width w/side brush 1117 mm

Height 1435 mm

Height with overhead guard 2045 mm

Track 94 mm

Wheelbase 97 mm

Main sweeping brush diameter 280 mm

Main sweeping brush length 710 mm

Side brush diameter 520 mm

Sweeping path width 710 mm

Sweeping path width with one side brush 1070 mm

Sweeping path width with two side brushes 1397 mm

Main sweeping brush pattern width 65 mm

Hopper weight capacity 135 kg

Hopper volume capacity 125 L

Dust filter area 4.5 sq m

GVWR 620 kg

Ceiling height minimum dumping clearance 2286 mm

Sound level -- continuous 81+ dB(A)

Sound level -- peak 81+ dB(A)

Vibration level at steering wheel does not exceed 2.5 m/s@

Vibration level at operator seat does not exceed 0.5 m/s@

GENERAL MACHINE PERFORMANCE

Item Measure

Maximum forward speed 8.0 km/h

Maximum reverse speed 4.8 km/h

Minimum aisle turn 2095 mm

Minimum turning radius, left 1400 mm

Minimum turning radius, right 1400 mm

Maximum rated incline with empty hopper 10_/18%

Maximum rated incline with full hopper 6_/11%

SPECIFICATIONS

736200 Gas/LPG 330379(2--2010)

POWER TYPE

Engine Type Ignition Cycle Aspiration Cylinders Bore StrokeRobin Piston Breakerless-

type spark4 Natural 1 84 mm 61 mm

Displacement Net power, governed Net power, maximum

338 cc 5.0 kw @ 2500 rpm 8.0 kw @ 3600 rpm

Fuel Cooling system Electrical system

Gasoline, 87 octaneminimum, unleaded. Fueltank: 7.2 L

Air cooled 12 V nominal

LPG,Fuel tank: 9 kg Vapor

50 A alternator

Idle speed (Fast) governed speed Firing order

2500 rpm (gov) 2500 rpm (gov) 1

Spark plug gap Valve clearance, cold Engine lubricating oil

0.6 mmGasoline and LPG

0.145 to 0.185 mm intake andexhaust

1.20 L 10W30SAE--SG/SH

STEERING

Type Power source Emergency steering

Front wheel, manual controlled Manual steering Manual

HYDRAULIC SYSTEMS

System Capacity Fluid TypeMain hydraulic reservoir 7.58 L (2 gal) ISO Grade 100 -- above 7_ C (45_ F)

ISO Grade 32 -- below 7_ C (45_ F)Main hydraulic total 9.48 L (2.5 gal)Hydraulic lift reservoir 0.53 L (.14 gal) ISO Grade 32 -- below 7_ C (45_ F)Hydraulic lift total 1.4 L (.37 gal)

BRAKING SYSTEM

Type OperationService brakes Mechanical disc brake (1), one front wheel, cable

actuatedParking brake Utilizes service brakes, cable actuated

TIRES

Location Type SizeFront (1) Solid 102 x 305 mmRear (2) Solid 90 x 305 mm

SPECIFICATIONS

6200 Gas/LPG 330379(9--2005)74

TOP VIEW

SIDE VIEW

1783 mm (70 in)

1067 mm(42 in)

2045 mm(80.5 in)

FRONT VIEW

1435 mm(56.5 in)

1397 mm(55 in)

352945

MACHINE DIMENSIONS

6200 Gas/LPG CE Operarot Manual (En)az295482.vo.msecnd.net/globalassets/globalassets/all...

Documents

Transcript of 6200 Gas/LPG CE Operarot Manual (En)az295482.vo.msecnd.net/globalassets/globalassets/all...