61508778 58421991 Paint Inspection and Control
-
Upload
pramod-athiyarathu -
Category
Documents
-
view
516 -
download
5
Transcript of 61508778 58421991 Paint Inspection and Control
Paint SchoolJPS-E / Control / 1
Inspection and
Control
Paint SchoolJPS-E / Control / 2
What is QA What is QA -- QC ?QC ?
QA = Quality Assurance(A documented management system)
QC = Quality Control (Inspection and testing routines)
Paint SchoolJPS-E / Control / 3
The Tasks of the Paint InspectorThe Tasks of the Paint Inspector• To ensure that the requirements of the coating specification are met.
• Verify the quality of work carried out by the contractor/yard.
• Prepare written records of the standardof work
- Approval (Satisfactory ? / Conforming ?)- Non-conformance
Paint SchoolJPS-E / Control / 4
An InspectorAn Inspector’’s Work Includes:s Work Includes:
• Be capable of interpreting the specifications• Understand the objective of the inspection • Inspect all structures to be painted• Ensure that all specified requirements are met• Document the results from the inspections• In case of non-conformance: Issue written reports
Paint SchoolJPS-E / Control / 5
• All paints that will be used• All relevant inspection methods and
inspection tools• Relevant standards• Methods involved in cleaning, pre-treatment
and paint application • The equipment used for pre-treatment and
application: Benefits and limitations
An Inspector Needs to Know:An Inspector Needs to Know:
Paint SchoolJPS-E / Control / 6
What Needs to be Inspected ?What Needs to be Inspected ?
• Shop-priming of the steel• The steel work
(Pre-blasting preparation)• Cleaning and surface preparation
prior to paint application • Application of paint • The applied paint film and its curing
conditions.
If relevant, the following stagesof the production need to be inspected
Paint SchoolJPS-E / Control / 7
Inspection at Shop primingInspection at Shop priming
• Cleanliness (No salt, oil, grease or other contaminants)
• Rust grade. A or B acc. To ISO 8501-1• Shot or grit blasted steel, to Sa 2 ½ acc. to
ISO 8501-1• Correct DFT (Usually 10 - 25 microns)• Satisfactory drying• No damages caused by conveyor.
Paint SchoolJPS-E / Control / 8
Inspection of steel work Inspection of steel work (Pre(Pre--blasting preparation)blasting preparation)
•Rounding of sharp edges.•Smoothing of rough welding seams.•Removal / grinding of weld spatter and
beads.•Cracks and pittings.•Surface faults like laminates etc.
The following items need to be inspected during construction
Paint SchoolJPS-E / Control / 9
Inspection of Cleaning and Inspection of Cleaning and Surface Preparation Prior to Surface Preparation Prior to
Application Application
•Cleanliness (salt, oil, grease and dust/dirt)
•Evaluation of present condition (rust grade)
•Surface preparation (e.g. blast cleaning)•Cleanliness of prepared surface
(salts, oil, grease, dust and dirt)•Climatic conditions
(temperature, relative humidity etc)
If relevant, the following conditionesmust be inspected / verified
Paint SchoolJPS-E / Control / 10
Inspection During ApplicationInspection During Application
• Ensure proper mixing of 2-pack paints• Ensure use of the correct thinner• Measuring the wet film thickness (WFT)• Number of coats as given in the
specification• Cleanliness between coats (salts, dust, oil
etc.)• Drying time / recoating intervals• Control of equipment: Pressure, nozzle etc.• Climatic conditions (Ventilation, Air and
steel temperature and the relative humidity)
The following must be verified,inspected or tested:
Paint SchoolJPS-E / Control / 11
Inspection After ApplicationInspection After Application
•Climatic conditions (Ventilation,Temperature and humidity)
•Curing / drying of the film•Dry film thickness (DFT)•Adhesion•Holiday detection
After application the following must be checked
Paint SchoolJPS-E / Control / 12
An Inspector Deals With An Inspector Deals With Several Parties Several Parties
• Customer / owner• The Yard• Contractor / sub-contractor• Paint supplier• Suppliers of equipment• Classification society
Paint SchoolJPS-E / Control / 13
Utstyr utlagt
Inspection ToolsInspection Tools
Paint SchoolJPS-E / Control / 14
Våtfilm måler
Wet FilmWet Film TThicknesshickness GaugeGauge
• ISO 2808• Wet film thickness gauge• To be used on flat, even
surfaces• 1. coat no problem• 2. Coat: Be careful if
First Coat is not fully cured/driedor ifFirst coat is soft or resoluble
Paint SchoolJPS-E / Control / 15
Tørrfilm målere Elektr. Magn.
Magnetic and Electromagnetic Magnetic and Electromagnetic Dry Film Thickness GaugesDry Film Thickness Gauges
• ISO 2808• Dry film thickness gauge• Calibrate on smooth surface
to zero and to thickness similar to be measured
• Check with your calibration foil frequently
• Plastic material foils wear easily. Replace frequently.
• No internal memory in gauge
Paint SchoolJPS-E / Control / 16
speil, lykt
Inspection Tools: Mirror and Flash lightInspection Tools: Mirror and Flash light
• Visual inspection• Important tools to be
able to inspect areas difficult to access
• For inspection in confined spaces: Use Ex approved equipment
Paint SchoolJPS-E / Control / 17
Jan, speil, lykt
Using Inspection Tools: Mirror and Flash lightUsing Inspection Tools: Mirror and Flash light
• Visual inspection• Important tools to be
able to inspect areas difficult to access
Paint SchoolJPS-E / Control / 18
MagnifierMagnifier
• Visual inspection• Handy tool when
looking for defects, to verify cleanliness and roughness of the substrate
Paint SchoolJPS-E / Control / 19
Clemco
Compartor
Surface Roughness acc. to ISO 8503Surface Roughness acc. to ISO 8503
• Example of a reference comparator: Clemco
• Surface profile comparator comprising four segments.
• Clemco - grit• Clemco shot also available • Check if the profile is
according to specification and the paint manufacturer’s recommendation
Paint SchoolJPS-E / Control / 20
Steel temperature
Contact ThermometerContact Thermometer
• Electronic instrument for measuring the steel temperature
• Steel temperature must be min. 3oC above the dew point
• Other types of thermometers are also available. E.g. magnetic thermometers
Paint SchoolJPS-E / Control / 21
Measuring the Relative HumidityMeasuring the Relative Humidity
• ISO 8502 - 4• Photo: Sling hygrometer for
measuring:- Dry temperature- Wet temperature
• Measure the temperature in the vicinity.
• Calculate the relative humidity
• Use together with dew point calculator
Paint SchoolJPS-E / Control / 22
Dew Point CalculatorDew Point Calculator• ISO 8502 - 4• For calculation of dew point• To be used together with
surface temperature thermometer and sling hygrometer.
• Use this frequently during pre-treatment, application and drying of the paint.
• Recommendation: Every 6 hours and when weather conditions are changing
Paint SchoolJPS-E / Control / 23
Tools for Marking Areas With DefectsTools for Marking Areas With Defects• Photo: Chalk for marking
areas during inspection• To be used both after pre-
treatment and painting• Areas with defects must be
marked properly• Other tools than chalk can be
usedNOTE: NOTE: Chalk may be considered
as contamination for some paint systems, and might have to be removed
Paint SchoolJPS-E / Control / 24
Gitter tester m prøveplate
Cross Cut Adhesion TestCross Cut Adhesion Test
• ISO 2409• Cross cut adhesion test• Cut vertical and horizontal
lines to form a grid• Apply a strong tape• Pull off the tape• Evaluate according to the
standard
Paint SchoolJPS-E / Control / 25
L.V. pore test
Low Voltage Pore DetectorLow Voltage Pore Detector
• ASTM G-62 -85, method A• Photo: Low voltage pore
detector• Detecting pinholes, voids or
metal particles in paint film up to 250 microns
• Non destructive test method• Will only detect defects down
to bare metal• The sponge must be wetted• Do not use excessive water
Paint SchoolJPS-E / Control / 26
Brunner H.V.P.D
Bruker.
High Voltage Pore DetectorHigh Voltage Pore Detector
• ASTM G-62-85, method B• Photo: High voltage pore detector• Destructive test method for detecting
pinholes, voids and thin spots in paint film
• Adjust voltage according to the film thickness or the paint manufacturers recommendation
• Gives a light or signal when pinhole or weak point is detected
Paint SchoolJPS-E / Control / 27
BSRA Instrument With ProbeBSRA Instrument With Probe
• For measuring the surface roughness
• Used prior to and after application of the paint
• Particularly for under water areas
• Important to follow instructions for use given by supplier
Paint SchoolJPS-E / Control / 28
Nærbilde ruhetsmåler
BSRA ProbeBSRA Probe
• Close up photo of B.S.R.A. Probe
• The probe is mounted on wheels
• Move slowly and steadily along the surface
• Do not lift the probe from the surface during the measurement
• Make sure to keep the probe and the wheels clean
Paint SchoolJPS-E / Control / 29
Bresle sett
Salt Test Equipment Salt Test Equipment -- Bresle TestBresle Test
• ISO 8502 - 6 (Sampling)• ISO 8502 - 9
(Conductivity) • Equipment for measuring
content of water soluble salt on substrate
• Bresle method
Paint SchoolJPS-E / Control / 30
Bresle sprøyte
8 - 41
Syringe Syringe -- Bresle Test: SamplingBresle Test: Sampling
• Bresle salt test • Syringe for injecting
distilled water• Shows how to inject the
distilled water through the frame and into the pad
• The water must be pumped in and out several times. Follow the standard
Paint SchoolJPS-E / Control / 31
Conductivity Meter Conductivity Meter -- Bresle testBresle test
• ISO 8502 - 9 (Conductivity)• Instrument for measuring the
conductivity • Salt level is measured as the
conductivity of the solution• Instrument shows the
conductivity which have to be recalculated to give the salt level on the substrate.
• Only water soluble salts !
Bresle instrument
8 - 44
Paint SchoolJPS-E / Control / 32
3 test plater
0590 - 50
Different Types of Salt Have Different Different Types of Salt Have Different Affinity to Water / HumidityAffinity to Water / Humidity
• Laboratory test.• Different types of salt are
applied on two test panels• Several month of exposure • Right: Clean water, no rust• Middle: Iron Sulphate, little
rust• Left: Sodium Chloride.
Heavy rust develops• At similar levels: Chlorides
more severe than Sulphates
Sodium Iron NoChloride Sulphate salt
Paint SchoolJPS-E / Control / 33
Insp. måler bunn
Using Using ““PIGPIG”” Universal on a ShipsUniversal on a Ships’’ HullHull
• PIG = Paint Inspection Gauge
• Destructive test method• Possible to verify the
number of coats applied• Possible to measure the
thickness of each individual coat
Paint SchoolJPS-E / Control / 34
Insp. avstrekk
8 - 49
PullPull--off Testing Of Paint On A Structureoff Testing Of Paint On A Structure
• ISO 4624• Pull off adhesion test.• Destructive test method• Here, connecting of the
device for pulling off the dollies
• Read and note the value• Several types of
instruments are available
Paint SchoolJPS-E / Control / 35
Dollys
8 - 46
PullPull--off Dollies Glued To The Structureoff Dollies Glued To The Structure
• ISO 4624• Pull off adhesion test• Dollies are glued to the
structure with a strong glue
• Prior to pull-off: Cut around the dolly, through the paint film and down to the substrate material
Paint SchoolJPS-E / Control / 36
Resultat
8 - 51
Area After PullArea After Pull--off Testingoff Testing
• ISO 4624• Pull off adhesion test• The adhesiveadhesive failure - fracture
between coats - or between coating and substrate must be evaluated
• Note adhesion failure, %• The cohesivecohesive failure - fracture
within the coating- must be evaluated.
• Note cohesion failure, %• Also: Note glue failure, %
Paint SchoolJPS-E / Control / 37
Standards Relating Methods for Standards Relating Methods for Evaluation of Degradation of Coatings Evaluation of Degradation of Coatings
Property Standard / Test methodBlistering ISO 4628 - 2, ASTM D 714
DIN 53209, BS 3900 H2
Rust gradeISO 4628 - 3, ASTM D 610DIN 53210, BS 3900 H3
Cracking ISO 4628 - 4, ASTM D 661DIN ISO 4628, BS 3900 H4
Flaking ISO 4628 - 5, DIN ISO 4628BS 3900 H5
Chalking ISO 4628 - 6
Paint SchoolJPS-E / Control / 38
Standards for Testing of Standards for Testing of Corrosion Protective PropertiesCorrosion Protective Properties
Property / Environment Standard / Test methodHumidity chamberCondensation
ISO 6270 (Condensation, water at 40 C)DIN 50017ASTM D 2247 (Condensation, water at 38 C)ASTM D 1735 (Humidity chamber)
Salt sprayISO 7253, ASTM B 117, BS 3900 - F12, DIN 53167, DIN 50021 ASTM G 85 (Prohesion test)
Natural weather exposure ISO 2810BS 3900 F 6
Weather-o-meter ASTM G 53
Cathodic disbonding ASTM G 8 (1500 mV/Ag-AgCl at 20 CASTM G 42 (1500 mV/Ag-AgCl at 60 C
Cathodic protection BS 3900 F 11
o
o
oo
Paint SchoolJPS-E / Control / 39
Standards for Evaluation Standards for Evaluation of Coated Surfaces of Coated Surfaces
Property Standard / Test method
Paint film thickness ISO 2808 (Wet and dry)SSPC - PA 2
Holiday detection ASTM G 62 (Low and high voltage)
Degradation of coatings ISO 4628
Paint SchoolJPS-E / Control / 40
Standards Relating toStandards Relating toMechanical PropertiesMechanical Properties
Property Standard / Test methodAdhesion (Cross cut) ISO 2409, DIN 53251, BS 3900-E6, ASTM 3359Adhesion (Pull-off) ISO 4624, ASTM 4541, BS 3900 - E10Adhesion (Shear strength)
ASTM D 1002 (Specified for Chartek)
Hardness ISO 2815 (Buchholz - methode)Hardness ISO 1522 (Kønig - pendel)Hardness BarcholElasticiy ISO 1520 (Cupping test)Flexibility ISO 6860 ASTM D 522
BS 3900 - E11 (Conical mandrel)Impact resistance ISO/TR 6272 - 79E ASTM D 2794 - 84
DIN 55669 BS 3900 - E3
Paint SchoolJPS-E / Control / 41
Standards Relating to Standards Relating to Physical PropertiesPhysical Properties
Property StandardSolids, % by weight ISO 1515 (105 °C - 3 hours)Solids by % volume ASTM D 2697 (1 hour - 110°C - dip)Drying time ISO 1517 (Surface dry)Flash point ISO 1523 (Closed cup)
ISO 3679 (Zeta flash)Milling grade ISO 1524Viscosity ISO 2431 (Flow cup)Paint film thickness ISO 2808Density ISO 2811 (Psykrometer)Gloss ISO 2813 (60 °C commonly used)Covering capacity ISO 2814Recoatability ASTM D 1640Curing of Zn-silicate ASTM D 4752 - 87
Paint SchoolJPS-E / Control / 42
A General Standard for A General Standard for Corrosion Protection: ISO 12944Corrosion Protection: ISO 12944
Part 1 General introduction.Part 2 Classification of environments.Part 3 Design considerations.Part 4 Types of surface and surface preparation.Part 5 Protective paint systems.Part 6 Laboratory performance test methods.Part 7 Execution and supervision of paint work.Part 8 Development of specifications for new work
and maintenance.
Paints and varnishes - Corrosion protection of steel structures by protective paints systems.
Paint SchoolJPS-E / Control / 43
Relevant Standards for Assessing Relevant Standards for Assessing Surfaces Prior to Paint ApplicationSurfaces Prior to Paint Application
Standard AreaISO 8501 Visual assessments of surface cleanliness.
ISO 8502 Tests for the assessment of surface cleanliness.
ISO 8503 Surface roughness characteristics of blast-cleaned steel substrates.
ISO 8504 Surface preparation methods.
Paint SchoolJPS-E / Control / 44
Surface PreparationSurface PreparationISO 8501 ISO 8501 -- 11
• Visual assessment of surface cleanliness
• Rust grades and preparation grades of uncoated steel
• Rust grades and preparation grades of steel after overall removal of previous coating
• Photographic examples of steel when blast cleaned with different abrasives
Paint SchoolJPS-E / Control / 45
ISO 8501
Rust grade A, B, C and D
Surface PreparationSurface PreparationStandard for Deciding Rust Grades Standard for Deciding Rust Grades
Paint SchoolJPS-E / Control / 46
Sa: Blast cleaning (grades 1, 2, 2 ½ and 3)
St.: Hand and power tool cleaning (grades 2 and 3)
Fl: Flame-cleaning (one grade)
Standard for deciding Preparation gradesStandard for deciding Preparation gradesISO 8501 ISO 8501 -- 11
Paint SchoolJPS-E / Control / 47
Surface PreparationSurface PreparationISO 8501 ISO 8501 -- 22
As for ISO 8501-1, but:For steel where previous coating has been
removed locally, not completely.
Paint SchoolJPS-E / Control / 48
PSa : Localised blast cleaning (grades 2, 2 ½ and 3)
PSt : Localised hand and power tool cleaning(grades 2 and 3)
PMa : Localised machine abrading (one grade)
Standard for deciding Preparation gradesStandard for deciding Preparation gradesISO 8501 ISO 8501 -- 22
Paint SchoolJPS-E / Control / 49
Surface PreparationSurface PreparationISO 8501 ISO 8501 -- 33
Visual assessment of surface cleanliness
Preparation grades of welds, cut edges and surface imperfections.
June 1998: Not yet approved
Paint SchoolJPS-E / Control / 50
Determination of Water Soluble SaltsDetermination of Water Soluble Salts
• Conductivity• Titration• Colour-reactions
Other Methods:• SCM 400 Salt Contamination Meter
The most frequently used methods are:
Paint SchoolJPS-E / Control / 51
Tests for the assessment of Tests for the assessment of Surface cleanliness: ISO 8502 Surface cleanliness: ISO 8502 (1 of 2)(1 of 2)
Part 1 Field test for soluble iron corrosion products Part 2 Laboratory determination of chloride on cleaned
surfaces.Part 3 Assessment of dust on steel surfaces prepared for
painting (pressure- sensitive tape method)Part 4 Guidance on the estimation of the probability of
condensation prior to paint application.Part 5 Measurement of chloride on steel surfaces
prepared for painting. Ion detector tube method.
Paint SchoolJPS-E / Control / 52
Tests for the assessment of Tests for the assessment of Surface cleanliness: ISO 8502 Surface cleanliness: ISO 8502 (2 of 2)(2 of 2)
Part 6 Sampling of soluble impurities on surfaces to be painted. Bresle method.
*Part 9 Analysis of soluble impurities on surfaces to be painted
Analysis methods for field use for ferrous salts.Part 10 Analysis of soluble impurities on surfaces to be
painted. Analysis methods for field use for oil and grease.
* Part 7 and 8 are not prepared
Paint SchoolJPS-E / Control / 53
Merckoquant test for iron• Quantitative test for detection of watersoluble
iron-salts• Indicator test strips impregnated with 2,2 bipyridyl• Sensitive within the range of 5mg/l to 250 mg/l• Destilled water• Specified test area 25 x 10 cm• Cotton• Glass/plastic containers
ISO 8502 Part 1ISO 8502 Part 1
Paint SchoolJPS-E / Control / 54
Soluble Iron Salts On Blast Cleaned Soluble Iron Salts On Blast Cleaned Surfaces. ISO 8502 Surfaces. ISO 8502 -- 1 Part 11 Part 1
Merckoquant test on steel substrate
Visual comparison with the standard
Steel substrate
Beaker with test solution
Paint SchoolJPS-E / Control / 55
Water Soluble Salts on BlastWater Soluble Salts on Blast--cleaned Steel. cleaned Steel. ISO 8502 ISO 8502 -- 1. Annex 31. Annex 3
• Potassium Hexacyanoferrate (III) test paper• The filter paper is impregnated with Potassium
Hexacyanoferrate (III)• Water / humidity• In case of the presence of Iron salts the colour will
turn blue• A qualitative , not a quantitative test
Paint SchoolJPS-E / Control / 56
Filter paper impregnated with Potassium Hexacyanoferrate
Blast cleaned steel
Blue spots
Water Soluble Salts on Blast Cleaned Steel Water Soluble Salts on Blast Cleaned Steel ISO 8502ISO 8502--1. Annex. 31. Annex. 3
Paint SchoolJPS-E / Control / 57
Laboratory Test Method for Laboratory Test Method for Determining Chlorides. ISO 8502Determining Chlorides. ISO 8502--2 2
Laboratory test method for determination of Chlorides
on a clean substrate
Paint SchoolJPS-E / Control / 58
ApprovedNot approved
Tape Blast cleaned steel
Assessment of Dust on Steel Surfaces Assessment of Dust on Steel Surfaces Prepared for Painting. ISO 8502Prepared for Painting. ISO 8502--33
Paint SchoolJPS-E / Control / 59
1.Quantity ratings 1, 2, 3, 4 and 5 corresponding to pictorial ref.
2.Dust size classes 0, 1, 2, 3, 4 and 5
Assessment of DustAssessment of DustISO 8502 ISO 8502 -- 33
Assessment for dust on Assessment for dust on steel surface prepared for paintingsteel surface prepared for painting
Paint SchoolJPS-E / Control / 60
Guidance on Estimating Probability of Guidance on Estimating Probability of Condensation prior to Paint ApplicationCondensation prior to Paint Application
Wet rag
Thermometres
ISO 8502ISO 8502--44
Paint SchoolJPS-E / Control / 61
1. Air temperature2. % Relative humidity3. Steel temperature4. Dew point
Steel temperature min. 3 oC above the dew point
HumidityHumidityISO 8502 ISO 8502 -- 44
Guidance on the estimation of the probability Guidance on the estimation of the probability of condensation prior to paint applicationof condensation prior to paint application
Paint SchoolJPS-E / Control / 62
Relative HumidityRelative Humidity
R.H.: % water vapour in the air as percentage of the total amount water vapour the air can contain at the same temperature.
ExampleAir at 20oC can contain 17.31 g. water/m3, but contain 15 g/m3. What is the R.H. ?
R.H. = = 86.65 %15 x 10017.31
Paint SchoolJPS-E / Control / 63
Chlorides on Steel SurfacesChlorides on Steel SurfacesISO 8502 ISO 8502 -- 55
Measurement of Chloride on steel surfaces prepared for painting
(The ion detection method)
Paint SchoolJPS-E / Control / 64
The Bresle MethodThe Bresle Method..ISO 8502 ISO 8502 -- 66
A method for assessment of soluble salts on the steel substrate:
The Bresle method
This is a quantitative test
Paint SchoolJPS-E / Control / 65
ConductometricConductometric Measurement of Measurement of Soluble Salts. Soluble Salts. ISO 8502 ISO 8502 -- 99
Field method for measuring conductivity (μ S) of solutions containing
water soluble salts
Paint SchoolJPS-E / Control / 66
Calculating Calculating the Salt Content on a Surfacethe Salt Content on a Surface
(L2 - L1) x 6 = mg. salt pr. m2
L2 = µS after washing
L1 = µS before washing
Used washing water, in ml.: 10 15 20 50Converting factor: 4 6 8 20
Paint SchoolJPS-E / Control / 67
UnitsUnits
1 mg = 1000 micro grams (µg)1 m2 = 10 000 cm2
1 mg/m2 = 0,1 micro g/cm2 (µg)1µg/cm2 = 10 mg/m2
Na+ + Cl- = NaCl (Sodium Chloride)Mol Weights = Cl- : 35,5 NaCl : 58,5
1 mg Cl- is corresponding to 58,5/35,5 mg NaCl= 1,6 mg NaCl
Paint SchoolJPS-E / Control / 68
Surface Roughness Characteristics of Surface Roughness Characteristics of BlastBlast--cleaned Steel Substrates: ISO 8503 cleaned Steel Substrates: ISO 8503
Part 1Specifications and definitions for ISO surface profile comparatives for the assessment of abrasive blast-cleaned surfaces.
Part 2 Method for the grading of surface profile of abrasive blast- cleaned steel - Comparator procedure.
Part 3Method for the calibration of ISO surface profile comparators and for the determination of surface profile- Focusing microscope procedure.
Part 4Method for the calibration of ISO surface profile comparatives and for the determination of surface profile - Stylus instrument procedure
Paint SchoolJPS-E / Control / 69
ISO 8503 ISO 8503 -- 11Nominal values and tolerancesNominal values and tolerances
a) Comparators for steel, blast-cleaned with grit abrasives
Segment Nominal reading µm
Toleranceµm
1 25 32 60 103 100 154 150 20
b) Comparators for steel, blast-cleaned with shot abrasives
Segment Nominal reading µm
Toleranceµm
1 25 32 40 53 70 104 100 15
Paint SchoolJPS-E / Control / 70
ISO 8503 ISO 8503 -- 11Limits of Profile GradesLimits of Profile Grades
a) Comparators for steel. Blast-cleaned with grit abrasives
Fine (G) Profiles equal to segment 1 and up to but excludingsegment 2
Medium (G) Profiles equal to segment 2 and up to but excludingsegment 3
Coarse (G) Profiles equal to segment 3 and up to but excludingsegment 4
b) Comparators for steel. Blast-cleaned with shot abrasives
Fine (S)
Medium (S)
Coarse (S)
Profiles equal to segment 1 and up to but excludingsegment 2Profiles equal to segment 2 and up to but excludingsegment 3Profiles equal to segment 3 and up to but excludingsegment 4
Paint SchoolJPS-E / Control / 71
Surface Roughness ProfileSurface Roughness Profile
• Stylus instruments• Elcometer Mod. 123• Testex Press-O-film• Microscope• Comparators
RugotestISO 8503 etc.
Paint SchoolJPS-E / Control / 72
Surface preparation methods: Surface preparation methods: ISO 8504.ISO 8504.
Part 1 General principles. Part 2 Abrasive blast-cleaning.Part 3 Hand- and power-tool cleaning.
Paint SchoolJPS-E / Control / 73
• Methods• Effectiveness• Fields of application
ISO 8504 ISO 8504 -- 22Abrasive blastAbrasive blast--cleaningcleaning
Paint SchoolJPS-E / Control / 74
• Methods• Equipment to be used• Procedure to be
followed
ISO 8504 ISO 8504 -- 33HandHand-- and Powerand Power--tool Cleaningtool Cleaning
Paint SchoolJPS-E / Control / 75
ISO 8504 ISO 8504 -- 11General PrinciplesGeneral Principles
• Selection of methods
Paint SchoolJPS-E / Control / 76
Method 1:
Method 2:
Method 3:
Method 4:
Method 5:
Determination of wet film thickness.
Determination of dry-film thickness by calculation from mass
Measurement of dry-film thickness by mechanically contacting method
Measurement of dry-film thickness by the profilometer method
Measurement of dry-film thickness using microscope method
Paints and varnishes Paints and varnishes -- Determination of Determination of film thickness: ISO 2808 film thickness: ISO 2808 -- 97 97 (1 of 2)(1 of 2)
Paint SchoolJPS-E / Control / 77
Method 6:
Method 7:
Method 8:
Method 9:
Method 10:
Magnetic method
Eddy current method
Non-contact methods
Gravimetric method (dissolving methods)
Determination of dry-film thickness on blast-cleaned steel substrates
Paints and varnishes Paints and varnishes -- Determination of Determination of film thickness: ISO 2808 film thickness: ISO 2808 -- 97 97 (2 of 2)(2 of 2)
Paint SchoolJPS-E / Control / 78
Wet paint100 90 80 70 60 50 40 30 20 10
Microns
Steel
Thickness given in microns
Wet Film Measuring CombWet Film Measuring CombISO 2808 ISO 2808 -- 97 Method No.197 Method No.1
Paint SchoolJPS-E / Control / 79
Paints and varnishes Paints and varnishes -- Determination of Determination of film thickness: ISO 2808 film thickness: ISO 2808 -- 9797Method No. 6: Magnetic method
• Magnetic (Method 6B) or magnetic instrument (Method 6A) for measuring total DFT
• Instruments for magnetic, metallic substrates• Calibration must be done in accordance
with instructions from the manufacturer• Before testing the paint system
must be properly cured.
Paint SchoolJPS-E / Control / 80
Paint and varnishes Paint and varnishes -- Determination of Determination of film thickness: ISO 2808 film thickness: ISO 2808 -- 9797
Method No. 7 - Eddy current method
• High frequency electromagnetic instrument• For non-magnetic substrates• Calibration in accordance with the
manufacturers instruction
Paint SchoolJPS-E / Control / 81
Method No. 10 - On blast cleaned steel substrates• Electromagnetic instruments• Calibration on a smooth steel surface min. 1,2 mm thick• For DFT not less than 25 microns and above 50 microns• Number of readings, as a guide:
– Reference area: at least 3 readings evenly– 2 reference areas every square meter on flat plates– 3 reference areas every length of a web– 2 reference areas every metre length for a flange– 2 reference areas every metre length for a pipe
Paint and varnishes Paint and varnishes -- Determination of Determination of film thickness: ISO 2808 film thickness: ISO 2808 -- 9797
Paint SchoolJPS-E / Control / 82
Measuring DFT on Small Areas Measuring DFT on Small Areas According to SSPC According to SSPC -- PA 2PA 2
Procedure1. Area of 10 m2: 5 spot measurements2. Each spot measurement: The average of 3 individual
readings made on one small area3. The average of 5 spot measurements must be within
specified range of film thickness4. Single spot measurements may be as low as 80% of
specified minimum film thickness5. Individual readings included in the spot measurements
may be less than 80% of minimum thickness
Paint SchoolJPS-E / Control / 83
Number of Film Thickness Number of Film Thickness Measurements acc. to SSPC Measurements acc. to SSPC -- PA 2PA 2
1. 10 m2 5 spots (on each spot: 3 measurements)
2. 30 m2 As for case 1 for each 10 m2
3. Up to100 m2 Select 3 areas, each of 10 m2
4. Above 100 m2 The first 100 m2 as for case 3For each following 100 m2 select randomly one area of 10 m2
Note: If measurements outside the specification for any 10 m2 in case 3 or 4 above are found then each 10 m2 shall be measured
Case Area Selection of Measurements
Paint SchoolJPS-E / Control / 84
Glove RagMEK
Rubbing 50 x
No Zinc on the Rag:CuredApproved
Curing Test of Zinc Curing Test of Zinc -- ethylsilicateethylsilicate with with MEK. (ASTM.D4752MEK. (ASTM.D4752--87)87)
A lot of Zinc on Rag:Not curedFurther curing / Reblasting
Paint SchoolJPS-E / Control / 85
Adhesion Testing by Knife and Adhesion Testing by Knife and Adhesive Tape: ASTM D 3359Adhesive Tape: ASTM D 3359--8787
• There are two test methods• The method to select depends on the DFT
Methode A: DFT above 125 micronsMethode B: DFT below 125 microns
(Above 125 if wider cuts are used)
Methode A: X - cut. Tape testMethode B: Cross - cut. Tape test
Paint SchoolJPS-E / Control / 86
Holiday Detection. Holiday Detection. LowLow Voltage.Voltage.ASTM G 62 Method AASTM G 62 Method A
• Low voltage: < 75 V DC• To detect pinholes, voids or metal particles to
be in the range of 25-250 microns.• Effective for paint films up to a DFT of 500
microns if a wetting agent is used in the water.• This is a non-destructive test.
Paint SchoolJPS-E / Control / 87
Holiday Detection. Holiday Detection. HighHigh Voltage.Voltage.ASTM G 62 Method BASTM G 62 Method B
High voltage: 900 - 20.000 V
Used to detect pinholes, voids andareas with thin paint films
This is a destructive test.
Paint SchoolJPS-E / Control / 88
Adhesion TestingAdhesion TestingASTM 3359ASTM 3359--87. Method B87. Method B
• < 50 microns = 1 mm apart (11 cuts)• 50 - 125 microns = 2 mm apart (6 cuts)• > 125 microns = Method A or 3 mm between cuts
1. Cuts: 20 mm long2. Brush with a soft brush3. Examine4. Cuts: 20 mm long at 90o on the original cuts5. Brush with...6. Tape 75 mm7. Within 90 + 30 sec. remove tape
Paint SchoolJPS-E / Control / 89
CrossCross--cut Test cut Test ISO 2409ISO 2409
Cutting toolSingle bladed knifeMulti-blade cutting tool with 6 cutting edges spaced1 mm or 2 mm apartSpacing of cuts0 - 60 microns - 1 mm spacing, hard substrates60- 120 microns - 2 mm spacing, soft substrates121 - 250 microns - 3 mm spacing, hard/soft substrates
Paint SchoolJPS-E / Control / 90
Procedure:Procedure:• Make 6 parallel cuts with defined space in the coating.• Repeat operation, crossing original cuts at 90o so that a
grid pattern is formed.• Brush with soft brush.• Apply adhesive tape and pull off.• Classify results in accordance with table 1.
CrossCross--cut Testcut TestISO 2409ISO 2409
Paint SchoolJPS-E / Control / 91
Classification of Cross Cut TestClassification of Cross Cut Test
Classi-fication Description Appearance of surface Six parallel cuts
0 Completely smooth: none of the squares detached1 Small flakes at the Intersections. Area affected 5 %
2 Flaked along the edges and/or at theIntersections. Area affected: 5-15%
3Flaked along the edges, wholly in large ribbons, and/or partly or wholly on different parts of the squares. Area affected: 15-35%
4Flaked along the edges in large ribbons and/orsome squares have detached partly or wholly. Area affected: 35-65%
5 Any degree of flaking that cannot even be classified by 4.
Paint SchoolJPS-E / Control / 92
ISO 4624ISO 4624PullPull--off test for adhesionoff test for adhesion
Procedure:• Test dollies glued onto the coating• Adhesive: Cyano-acrylate or solvent free epoxy• Remove adhesive and coating around the dollies• Pull off test-dollies vertical to the surface• Read adhesion value and report the type of fracture
Fractures:• Adhesion failure - fracture between coats or substrate and 1. coat• Cohesion failure - fracture within a coat
Paint SchoolJPS-E / Control / 93
Instruments:Instruments:• Elcometer Adhesion Tester• Saeberg Adhesion Tester (pneumatic)• Hate Adhesion Tester (hydraulic)• PAT
ISO 4624ISO 4624PullPull--off test for adhesionoff test for adhesion
Paint SchoolJPS-E / Control / 94
Paint Failures Commonly OccurringPaint Failures Commonly Occurring
• Holidays, too low DFT• Sags and runs• Orange peel• Dry spraying• Over spray• Pinholes, popping• Fish-eye• Wrinkling / lifting
• Sweating• Poor drying / curing• Blisters• Rust penetration• Cracking• Flaking• Chalking• Discolouration
Paint SchoolJPS-E / Control / 95
ISO 4628ISO 4628
• Evaluation of degradation of paint coatings
• Designation of intensity, quality and size of common types of defect
Paint SchoolJPS-E / Control / 96
Content of the StandardContent of the StandardISO 4628ISO 4628
Part 1 General principles and rating schemesPart 2 Designation of degree of blisteringPart 3 Designation of degree of rustingPart 4 Designation of degree of cracking
Part 5 Designation of degree of flakingPart 6 Designation of degree of chalking
The standard consists of six parts
Paint SchoolJPS-E / Control / 97
ISO 4628/1ISO 4628/1Part 1: General principles and rating schemesPart 1: General principles and rating schemes
Uniform deterioration.Rating scheme for designation the intensity of deterioration
consisting of a uniform change in the visual appearance of the paint coating.
Rating Intensity of change0 unchanged, i.e. no perceptible change12345
very slight, i.e. just perceptible changeslight i.e. clearly perceptible changemoderate, i.e. very clearly perceptible changeconsiderable, i.e. pronounced changesevere, i.e. intense change
Paint SchoolJPS-E / Control / 98
ISO 4628/1ISO 4628/1Part 1: General principles and rating schemesPart 1: General principles and rating schemes
Scattered defects.Rating scheme for designating the quantity of defects consisting
of discontinuities or other local imperfections of the paint coating.
RatingQuantity of defects
(relative to a test surface area of 1 to 2 dm²)0 none, i.e. no detectable defects
1
2
3
4
5
very few, i.e. some just significant defects
few, i.e. small but significant amount of defects
Moderate, i.e. medium amount of defects
considerable, i.e. serious amount of defects
dense, i.e. dense pattern of defects
Paint SchoolJPS-E / Control / 99
ISO 4628/1ISO 4628/1Part 1: General principles and rating schemesPart 1: General principles and rating schemes
Rating scheme for designating the size (order of magnitude) of defects
Class Size of defect0
1
2
3
4
5
not visible under 10 X magnification
only visible under magnification up to 10 X
just visible with normal corrected vision
clearly visible with normal corrected vision (up to 0,5 mm)
range 0,5 to 5 mm
larger than 5 mm
Paint SchoolJPS-E / Control / 100
ISO 4628/1ISO 4628/1Test reportTest report
The test report shall contain at least the following information:a) the type and identification of the product tester;b) a reference to this International Standard (ISO 4628/1);c) the type of defect;d) the intensity of the defect (table 1) or,e) the quantity of the defect (table 2);f) the rating, if any, of the size of the defect in brackets preceded
by the letter “S”.Examples: cratering of top coat : 2 (S3)
whitening : 4rivelling : 3 (S2)
Paint SchoolJPS-E / Control / 101
ISO 4628/2ISO 4628/2Part 2: Designation of degree of blisteringPart 2: Designation of degree of blistering
RatingRate the density and size of the blisters in a paint coating by means of the pictorial standards
NOTE - The photographic reference standards have been adopted from ASTM D 714-56The correlation between the ISO and the ASTM rating system is as shown in the table.
Table - Correlation between ISO and ASTM rating systems
Density SizeASTM ISO ASTM ISO
None
(less than few)
Few
Medium
Medium - Dense
Dense
0
1
2
3
4
5
(smaller than 8)
8
6
4
2
1
2
3
4
5
Paint SchoolJPS-E / Control / 102
ISO 4628/2ISO 4628/2Part 2: Designation of degree of blisteringPart 2: Designation of degree of blistering
Test reportTest reportThe test report shall contain at least the following information:a) the type and identification of the product tested;b) a reference to this International Standard (ISO 462/2);c) the numerical rating of the density of blistering;d) the numerical rating of the size of blistering for example:
blisters 2 (S2)Where a test piece exhibits blisters of varying size, quote as the size rating that of the largest blisters which are numerous enough to be typical of the test piece.
e) the date of the examination
Paint SchoolJPS-E / Control / 103
ISO 4628/3ISO 4628/3Part 3: Designation of degree of rustingPart 3: Designation of degree of rusting
RatingRatingDesignate the degree of rust formation by reference to the pictorial standards
Degree Area rusted %Ri 0
Ri 1
Ri 2
Ri 3
Ri 4
Ri 5
0
0,05
0,5
1
8
40/50
Paint SchoolJPS-E / Control / 104
Assessment of Area Ratio for Assessment of Area Ratio for Corrosion Breakdown Corrosion Breakdown
0.1 %
.
..
...
. ..
.
1.0 %
10 %
30 %
3.0 %
20 %
Paint SchoolJPS-E / Control / 105
ISO 4628/3ISO 4628/3Part 3: Designation of degree of rustingPart 3: Designation of degree of rusting
Correlation between ISO and European rust scalesISO rust scale European rust scale
Ri 0Ri 1Ri 2Ri 3Ri 4Ri 5
Re 0Re 1Re 2Re 3Re 5Re 7
Approximate correlation between ISO and ASTM rust scalesISO rust scale European rust scale
Ri 0Ri 1Ri 2Ri 3Ri 4Ri 5
109764
1 to 2
Paint SchoolJPS-E / Control / 106
ISO 4628/3ISO 4628/3Part 3: Designation of degree of rustingPart 3: Designation of degree of rusting
Test report:Test report:The test report shall contain at least the following information:a) the type and identification of the product tested;b) a reference to this International Standard (ISO 4628/3);c) the numerical rating of the rusted area;d) the numerical rating of the size of the rust spots, if desired,
for example:Rust: Ri 3 (S4) = rusted area, as a percentage of rust, approximates standard 3, the sizes of the individual rust spots of the order of a few millimeters.
e) the date of the examination
Paint SchoolJPS-E / Control / 107
ISO 4628/4ISO 4628/4Part 4: Designation of degree of crackingPart 4: Designation of degree of cracking
RatingRate the quantity of cracking by reference to table 2 of ISO 4628/1 and using as examples figures 1 or2, depending on the type of cracking
Rating scheme for the designation of the size of cracks
Class Size of cracks012345
Not visible under 10 X magnificationOnly visible under magnification up to X 10Just visible with normal corrected visionClearly visible with normal corrected visionLarge cracks generally up to 1 mm wideVery large cracks generally more than 1 mm wide
Three main types of failure by cracking are to be distinguished:a) surface cracks which do not fully penetrate the top coatb) cracks which penetrate the top coat, the underlying coat(s) being substantially unaffected;c) cracks which penetrate the whole coating system
Paint SchoolJPS-E / Control / 108
ISO 4628/4ISO 4628/4Part 4: Designation of degree of crackingPart 4: Designation of degree of cracking
Test report:Test report:a) the type and identification of the product tested;b) a reference to this International Standard (ISO 4628/4);c) the numerical rating of the quantity of cracking;d) the numerical rating of the size of cracking;e) the depth of cracking (a. b. or c), where possible, for example:
cracking 2 (S3) bIf necessary, the standard assessment may be amplified in words, for example “linear cracking”. The use of such comments shall, however, be avoided wherever possible:
e) the date of the examination
Paint SchoolJPS-E / Control / 109
ISO 4628/5ISO 4628/5Part 5: Designation of degree of flakingPart 5: Designation of degree of flaking
Scale for the quantity of flakingClass Flaked area
012345
00,10,31315
Scale the average size of areasClass Size of flaking
0
12345
not visible under X magnification
up to 1 mmup to 3 mmup to 10 mmup to 30 mm
larger than 30 mm
The main types of failure by flaking are to be distinguished:
a) Top coats flaking from underlying coat;
b) Whole coating system flaking from substrate
Paint SchoolJPS-E / Control / 110
ISO 4628/5ISO 4628/5Part 5: Designation of degree of flakingPart 5: Designation of degree of flaking
Test reportTest reportThe test report shall contain at least the following information:a) the type and identification of the product tested;b) a reference to this International Standard (ISO 4628/5);c) the numerical rating of the quantity of flaking;d) the numerical rating of the size of flaking;e) the depth of cracking (a or b), for example;
flaking 3 (S2) a
Paint SchoolJPS-E / Control / 111
ISO 4628/6ISO 4628/6
Part 6:Rating of degree of chalking by tape methodSelf-adhesive, transparent tape, of width 25 mm + 10 mm
– Chalking is removed by adhering to the tape– Black or white background– Comparing the amount of chalk on the tape with
pictorial reference standard in figure 1
Paint SchoolJPS-E / Control / 112
ISO 4628/6ISO 4628/6Part 6: Rating of degree of chalking by tape methodPart 6: Rating of degree of chalking by tape method
Test reportTest reporta) all details necessary for the identification of the product tested;b) a reference to this International Standard (ISO 4628-6);c) the type of weathering (artificial or natural) of the coating;d) all details necessary for the identification of the adhesive tape
used;e) all details necessary for the identification of the substrate used as
background for the adhesive tape;f) the numerical rating of the degree of chalking;g) any deviation from the procedure specified;h) the date of the examination
Paint SchoolJPS-E / Control / 113
Specifications for metallic blast-cleaning abrasives.The standard consists of 5 parts
Part 1 Introduction
Part 2 Chilled iron grit
Part 3 High carbon cast steel shot and grit
Part 4 Low carbon cast steel shot
Part 5 Cut steel wire
Content of the Content of the Standard ISO 11124Standard ISO 11124
Paint SchoolJPS-E / Control / 114
Content of the Content of the Standard ISO 11125 Standard ISO 11125
Methods of test for metallic blast-cleaning abrasives.The standard consists of 8 parts
Part 1 SamplingPart 2 Determination of particle size distributionPart 3 Determination of hardnessPart 4 Determination of apparent densityPart 5 Determination of defective particles
and microstructurePart 6 Determination of matterPart 7 Determination of moisturePart 8 Abrasive mechanical properties
Paint SchoolJPS-E / Control / 115
Specification for non-metallic blast-cleaning abrasive.The standard consists of 10 parts
Part 1 IntroductionPart 2 Silica sandPart 3 Copper refinery slagPart 4 Coal furnace slagPart 5 Nickel refinery slagPart 6 Iron furnace slagPart 7 Fused aluminium oxidePart 8 Olivine sandPart 9 StaurolitePart 10 Garnet
Content of the Content of the Standard ISO 11126 Standard ISO 11126
Paint SchoolJPS-E / Control / 116
Content of the Content of the Standard ISO 11127Standard ISO 11127
Test methods for non-metallic blast-cleaning abrasives.The standard consists of 8 parts
Part 1 SamplingPart 2 Determination of particle size distributionPart 3 Determination of apparent densityPart 4 Determination of hardness by a glass slide testPart 5 Determination of moisture contentPart 6 Determination of water soluble
contamination by conductive measurementPart 7 Determination of water soluble chloridesPart 8 Abrasive mechanical properties
Paint SchoolJPS-E / Control / 117
Contamination of AbrasivesContamination of Abrasives
• Water• Oil and grease• Chlorides• Sulphates
The abrasives can be contaminated with
Paint SchoolJPS-E / Control / 118
The Content of Humidity of the The Content of Humidity of the Abrasives Acc. to ISO 11127 Abrasives Acc. to ISO 11127 -- 55
• Laboratory test
• Requirement: Maximum 0,2 %
Paint SchoolJPS-E / Control / 119
Content of Water soluble Content of Water soluble Contaminants acc. to ISO 11127 Contaminants acc. to ISO 11127 -- 66
Conductivity measurementsA sample of 100 g. of the abrasives100 ml of waterShake for 5 minutes and let rest for 1 hourShake again for another 5 minutesMeasure the conductivity at a temperature of 10 oCRequirement: Maximum conductivity of 25 mS/m
Paint SchoolJPS-E / Control / 120
• According to ASTM D 4940
• Mix 300 ml of abrasive and 300 ml water
• Stir for 1 min. let stand for 8 min., stir again for 1 min.
Oil content (AB-1)No presence of oil, either on top or as an emulsion after 30 min.
How to Control the AbrasivesHow to Control the Abrasives
Conductivity (AB-1)Fill the liquid for test and measure the conductivity.Max 25 mS/m
Paint SchoolJPS-E / Control / 121
Is the Abrasive Free From Is the Abrasive Free From Oil and Grease ?Oil and Grease ?
• Put a handful of the abrasives into a beaker• Pour clean, fresh water into the beaker• Shake the mixture• A film of oil will form on top of the water if
oil or grease are present
This is of particular importance to check when abrasives are recycled
Paint SchoolJPS-E / Control / 122
Testing and Evaluation.Testing and Evaluation.Marine Atmosphere Marine Atmosphere (1 of 2)(1 of 2)
Test method Standards CommentsPhysical testingAdhesionAdhesionFlexibilityElasticityHardnessImpact resistanceGlossAbrasion resistance
ISO 2409ISO 4624ISO 1510ISO 1520ISO 2815ISO 6272ISO 2813ASTM D 4060
Before and after exposureBefore and after exposureBefore and after exposureBefore and after exposure
Exposure conditions:SaltsprayProhesion testUV-cabinetCondensation chamberHumidity chamberWeatheringResistance to liquids
ISO 7253 or ASTM B 117
ASTM G 53ISO 6270BS 3900ISO 2810ISO 2812 Oil, petroleum , etc.
Paint SchoolJPS-E / Control / 123
Test method Standards Comments
Evaluation of paint films BlisteringRustCrackingDelaminationChalkingScribe
ISO 4628/2ISO 4628/3ISO 4628/4ISO 4628/5ISO 4628/6ASTM D 1654
Evaluation of the liquid paint
Appearance in tin
Application properties
ISO 2431
ISO 2884
“Flow time”
Viscosity
Testing and Evaluation.Testing and Evaluation.Marine Atmosphere Marine Atmosphere (2 of 2)(2 of 2)
Paint SchoolJPS-E / Control / 124
Surface RoughnessSurface Roughness
• Stylus instruments• Elcometer Mod. 123• Testex Press-O-film• Microskope• Comparator
–Rugotest No. 3–ISO 8503 etc.
Paint SchoolJPS-E / Control / 125
Steel
Rag soaked with solvent
No reaction:Chemically curing
Paint dissolves:Physically drying
Using Solvents to DetermineUsing Solvents to DetermineGeneric Type of PaintGeneric Type of Paint
2 coat paintLifting:
Oxidatively curing
Paint SchoolJPS-E / Control / 126
DaylyDayly LogsLogs
• Stål-temperatur• Luft-temperatur• Relativ fuktighet• Duggpunkt• Objekt malt• Navn på relevant personell• Hva ble diskutert• Film-tykkelse (skal måles,
også for flekking veddokking)
• NB-navn, nr, objekt• Prod. nr.• Malingens opprinnelsessted• Eksakt spesifikasjon• Areal - m2
• Forbehandling, spesifisert ogutført
• Andre kommentarer
Paint SchoolJPS-E / Control / 127
Surface temperature of the
structure must be minimum
3 3 °°C above the dew pointC above the dew point
Atmospheric Conditions.Atmospheric Conditions.Requirement During Blasting and PaintingRequirement During Blasting and Painting
Paint SchoolJPS-E / Control / 128
Part 1 General introduction and classification
Part 2 Silica sandPart 3 Copper Refinery SlagPart 4 Coal Furnace SlagPart 5 Nickel Refinery SlagPart 6 Iron Furnace SlagPart 7 Silica sand
ISO 11126 Standardises the ISO 11126 Standardises the NonNon--metallic Abrasivesmetallic Abrasives
Paint SchoolJPS-E / Control / 129
• Thank You !