60HZ ALTERNATORS Product Catalog - Linz Electric€¦ · sinGle-phase brushless synchronous...
Transcript of 60HZ ALTERNATORS Product Catalog - Linz Electric€¦ · sinGle-phase brushless synchronous...
-
60HZ ALTERNATORSProduct Catalog
-
2 For more information and support contact: T.+1 (847) 595 1473 - [email protected] - www.linzelectric.us
4 POLE ALTERNATORS
THREE-PHASE BRUSHLESS SYNCHRONOUS ALTERNATORS WITH AVR: E1X13/4 - SLT - PRO18 - PRO22 - PRO28 - PRO35-PRO40 6
4 POLE THREE-PHASE ALTERNATORS EFFICIENCY TABLE 8
SINGLE-PHASE BRUSHLESS SYNCHRONOUS ALTERNATORS WITH AVR: E1X13/4 1PH- SLS - PRO18 1PH - PRO22 1PH 9
TECHNICAL FEATURES E1X - SL - PRO 10
ACCESSORIES FOR E1X - SL - PRO 11
THREE-PHASE SYNCHRONOUS ALTERNATORS WITH BRUSHES: E1S13/4 12
SINGLE-PHASE BRUSHLESS SYNCHRONOUS ALTERNATORS WITH CAPACITOR: E1C13/4 13
GENERAL FEATURES 14
2 POLE ALTERNATORS
THREE-PHASE BRUSHLESS SYNCHRONOUS ALTERNATORS WITH AVR: E1X13/2 16
SINGLE-PHASE BRUSHLESS SYNCHRONOUS ALTERNATORS WITH AVR: E1X13/2 1PH 17
TECHNICAL FEATURES E1X/2 18
SINGLE-PHASE BRUSHLESS SYNCHRONOUS ALTERNATORS WITH CAPACITOR: SP10 - E1C10 - E1C11 - E1C13/2 19
TECHNICAL FEATURES SP10-E1C 20
THREE-PHASE SYNCHRONOUS ALTERNATORS WITH BRUSHES: E1S10- E1S11 - E1S13/2 21
THREE-PHASE SYNCHRONOUS ALTERNATORS WITH BRUSHES AVR AND COMPOUND: E1S10/KE - E1S11/KE 22
GENERAL FEATURES 23
CONNECTIONS TO THE TERMINAL BOARD 24
TECHNICAL DRAWINGS AND DIMENSIONS 26
TABLE OF CONTENTS
-
THE COMPANY
LINZ ELECTRIC S.p.A., part of the Pedrollo Group, is specialized in the production of alternators and rotating welders. It was founded in 2002 and became in few years one of the major players in the sector. The knowledge and long experience of its designers together with the strong propensity for innovation and a natural tendency for investment has quickly led to the development of a full range of products whose high quality standards are recognized and appreciated worldwide by the most important gen-sets manufacturers. In accordance with its deep values the main focus of Linz Electric has always been the Customer Satisfaction by controlling the key points of the production through a strong vertical integration, a constant focus on the Product Quality and a quick and complete Service.
LINZ ELECTRIC lands in the States in 2015, with a new subsidiary, LINZ ELECTRIC INC. based in Northbrook, Illinois. Thanks to this important step and to the proximity to the market we have been offering an optimized pre- and after-sales service to our North American customers , quick deliveries and customer support through the competence that always distinguishes Linz Electric and its people.
Arcole, Verona, Italy
Northbrook, IL, USA
-
4-POLE ALTERNATORS
-
6 For more information and support contact: T.+1 (847) 595 1473 - [email protected] - www.linzelectric.us
MODEL
3 Phase277/480V - High WYE 138/240V - Low WYE
kVA
3 Phase 240/416V - High WYE 120/208V - Low WYE
kVA
Single Phase120/240V - Series Parallel
kVA
Net weight SAE(lbs)
150/40 125/40 105/40 80/40 150/40 125/40 105/40 80/40 150/40 125/40 105/40 80/40
E1X1
3/4
E1X13S A/4 9 8 7.5 6.5 8 7.5 6.5 5.5 5 5 4.5 4 140
E1X13S B/4 10.5 10 9.5 8.5 9.5 9 8.5 7.5 6 6 5.5 5 154
E1X13S C/4 13 12 11 9.5 12.5 11 10.5 9 8 7 7 6 169
E1X13M E/4 18 17 15.5 13.5 14.5 14 13 11.5 9.5 9 8.5 7.5 212
E1X13M F/4 21 19 17.5 15.5 18.5 17 15.5 13.5 12 11 10 8.5 221
SLT SLT18 MC 19 18 17 15 16.5 16 15 13 11 10.5 10 8.5 251
SLT18 MD 26 24 22 19 24 21 20 17.5 15.5 13.5 13 11.5 256
PRO1
8
PRO18S A/4 26 24 22 19 24 21 20 17.5 15.5 13.5 13 11.5 267
PRO18S B/4 32 30 27.5 24 28.5 26 24 21 18.5 17 15.5 13.5 297
PRO18S C/4 38 36 33.5 29 36 34 32 28 23.5 22 21 18.5 331
PRO18M D/4 45 42 38.5 33.5 40 38.5 36 31.5 26 25 23.5 20.5 375
PRO18M E/4 55 50 47 41 50 48 45 39.5 32.5 31 29.5 26 441
PRO18L F/4 64 60 54 47 58 56 48 42 38 36.5 31 27 522
PRO18L G/4 76 72 66 57.5 62 60 50 43.5 40.5 39 32.5 28.5 590
PRO2
2
PRO22S A/4 83 75 70.5 61.5 71 65 61 53.5 46 42.5 39.5 34.5 581
PRO22S B/4 95 90 83 72.5 86 81 75 65.5 56 52.5 49 43 651
PRO22S C/4 110 100 95 83 100 94 88 77 65 61 57 50 697
PRO22S D/4 130 120 111.5 97.5 118 110 101 88 76.5 71.5 69.5 57 781
PRO22M E/4 167 155 145 126.5 148 139 129 113 96 90.5 84 73.5 957
PRO22M F/4 195 180 167.5 146 162 150 139 121 105 97.5 90.5 79 1046
PRO22M G/4* 210 190 176 153.5 180 165 150 131 117 107 97.5 85 1046
• IP23 PROTECTION • COMPACT AND MECHANICALLY RESISTANT • EXCELLENT WAVE FORM• MINIMUM MAINTENANCE• HIGH EFFICIENCY• WITH AUXLIARY WINDING (see page 10)• UL RECOGNIZED INSULATION SYSTEM (Standards: UL 1446, Systems of Insulating Materials - General
CSA-C22.2 No. 0, Appendix B, General Requirements - Canadian Electrical Code, Part II)• cCSAus CERTIFICATION (Standards: CAN/CSA –C22.2 No. 100-14 (R2009) Motors and Generators, UL1004-1
2nd ed. Rotating Electrical Machines–General Requirements, UL1004-4 2nd ed. Electric Generators)
• For overall dimensions see from page 26 to 30
INSULATION SYSTEM 250H
PRO18
• Brushless synchronous alternators with AVR • 0.8 Power Factor • Class H Insulation• 12 Leads (*6 Leads)• With Auxiliary Winding
60HZ - THREE PHASE4 POLE / 1800 RPMBRUSHLESS WITH AVR
-
7For more information and support contact: T.+1 (847) 595 1473 - [email protected] - www.linzelectric.us
MODEL
3 Phase277/480V - High WYE 138/240V - Low WYE
kVA
3 Phase 240/416V - High WYE 120/208V - Low WYE
kVA
Single Phase120/240V - Series Parallel*240V - Delta riconnected
kVA
Net weight SAE(lbs)
150/40 125/40 105/40 80/40 150/40 125/40 105/40 80/40 150/40 125/40 105/40 80/40
PRO2
8
PRO28S A/4 234 215 192 168 213 196 175 153 138 127 114 100 1243
PRO28S B/4 260 240 210 183 245 225 200 175 159 146 130 113 1303
PRO28S C/4 305 270 240 209 290 260 225 196 188 169 146 127 1473
PRO28S D/4 320 300 250 218 310 290 240 209 201 188 156 136 1611
PRO28M E/4 370 360 300 262 345 335 277 242 224 218 180 157 1838
PRO28M F/4 435 420 360 314 400 390 335 292 260 253 218 190 2092
PRO28L G/4* 490 480 430 375 435 430 386 337 283 279 251 219 2280
PRO3
5
PRO35S B/4 575 540 485 423 520 480 440 384 338 312 286 250 2610
PRO35S C/4* 635 600 540 471 575 550 495 432 374 357 322 281 2783
PRO35S D/4 695 660 590 515 615 580 510 445 400 377 331 289 2960
PRO35M E/4* 760 720 660 576 680 640 590 515 442 416 383 334 3294
PRO35M F/4* 840 800 730 637 750 715 650 567 487 465 422 368 3308
PRO35M G/4 920 870 780 681 830 785 700 611 539 510 455 397 3656
PRO35L H/4* 1040 960 935 816 915 870 860 759 595 565 559 493 4116
PRO4
0
PRO40S A/4* 1200 1116 1044 920 1090 1050 975 850 740 680 620 540 4473
PRO40S B/4* 1370 1260 1176 1000 1130 1100 1020 900 870 800 730 640 4508.5
PRO40M C/4* 1500 1400 1300 1150 1300 1250 1150 1000 980 900 820 720 4965
PRO40M D/4* 1750 1620 1540 1300 1600 1480 1400 1200 1090 1000 910 800 5809
PRO40L E/4* 1920 1800 1650 1470 1750 1650 1500 1350 1200 1100 1000 880 7220
• IP23 PROTECTION • COMPACT AND MECHANICALLY RESISTANT • EXCELLENT WAVE FORM• MINIMUM MAINTENANCE• HIGH EFFICIENCY• WITH AUXLIARY WINDING (see page 10)• UL RECOGNIZED INSULATION SYSTEM (Standards: UL 1446, Systems of Insulating
Materials - General CSA-C22.2 No. 0, Appendix B, General Requirements - Canadian Electrical Code, Part II)
• For overall dimensions see from page 31 to 33
INSULATION SYSTEM 250H
PRO35
• Brushless synchronous alternators with AVR • 0.8 Power Factor • Class H Insulation• 12 Leads (*6 Leads)• With Auxiliary Winding
60HZ - THREE PHASE4 POLE / 1800 RPMBRUSHLESS WITH AVR
-
8 For more information and support contact: T.+1 (847) 595 1473 - [email protected] - www.linzelectric.us
60HZ - THREE PHASE4 POLE / 1800 RPMEFFICIENCY TABLE
MODEL Leads
3 Phase277/480V - High WYE 138/240V - Low WYE
60 Hz - 1800 rpm - cosφ = 0.8125/40
kVA eff.%
E1X1
3/4
E1X13S A/4 12 8 81E1X13S B/4 12 10 83E1X13S C/4 12 12 84.6E1X13M E/4 12 17 86E1X13M F/4 12 19 86.4
SLT SLT18 MC 12 18 87.4
SLT18 MD 12 24 87.8
PRO1
8
PRO18S A/4 12 24 87.8PRO18S B/4 12 30 88.2PRO18S C/4 12 36 88.8PRO18M D/4 12 42 90.4PRO18M E/4 12 50 91.1PRO18L F/4 12 60 91.2PRO18L G/4 12 72 91.4
PRO2
2
PRO22S A/4 12 76 90.4PRO22S B/4 12 90 90.4PRO22S C/4 12 102 90.6PRO22S D/4 12 120 90.9PRO22M E/4 12 156 92.5PRO22M F/4 12 180 92.8PRO22M G/4 6 192 93.5
SLT18
INSULATION SYSTEM 250H
MODEL Leads
3 Phase277/480V - High WYE 138/240V - Low WYE
60 Hz - 1800 rpm - cosφ = 0.8125/40
kVA eff.%
PRO2
8
PRO28S A/4 12 215 92.5PRO28S B/4 12 240 92.5PRO28S C/4 12 270 92.7PRO28S D/4 12 300 93.2PRO28M E/4 12 360 93.3PRO28M F/4 12 420 94PRO28L G/4 6 480 94.2
PRO3
5PRO35S B/4 12 540 95.5PRO35S C/4 6 600 95.9PRO35S D/4 12 660 95.9PRO35M E/4 6 720 95.7PRO35M F/4 6 804 95.4PRO35M G/4 12 870 96.2PRO35L H/4 6 960 96.5
PRO4
0
PRO40S A/4 6 1116 96.1
PRO40S B/4 6 1260 96.3
PRO40M C/4 6 1400 96.5
PRO40M D/4 6 1620 96.5
PRO40L E/4 6 1800 96.9
-
9For more information and support contact: T.+1 (847) 595 1473 - [email protected] - www.linzelectric.us
MODELSingle Phase Dedicated
120/240V - Series ParallelkVA
Net weight SAE(lbs)
Eff%cosφ = 1
150/40 125/40 105/40 80/40
E1X1
3/4 1
PH
E1X13S A/4 1PH 6.5 6 5.5 4.8 140 81
E1X13S B/4 1PH 7.5 7 7 6 154 82
E1X13S C/4 1PH 9.5 9 8 7 169 84.5
E1X13M E/4 1PH 13 12.5 11.5 10 212 85.5
E1X13M F/4 1PH 15.5 14 13 11.5 221 86
SLS SLS18 MC 13 12 11 9.5 247 85.8
SLS18 MD 18.5 18 16.5 14.5 254 87
PRO1
8 1PH
PRO18S A/4 1PH 18.5 18 16.5 14.5 267 87
PRO18S B/4 1PH 23.5 22 20 17.5 297 87
PRO18S C/4 1PH 28 26.5 24.5 21.5 331 88.2
PRO18M D/4 1PH 33 30.5 28 24.5 375 90
PRO18M E/4 1PH 40 36.5 34.5 30 441 90.6
PRO18L F/4 1PH 46.5 44 39.5 34.5 522 90.8
PRO18L G/4 1PH 55.5 52.5 48 42 590 92
PRO2
2 1PH
PRO22S A/4 1PH 58 54 50 44 581 90
PRO22S B/4 1PH 69 65 60 55 651 90.2
PRO22S C/4 1PH 76 72 67 60 697 90
PRO22S D/4 1PH 91 86 80 72 781 90.5
PRO22M E/4 1PH 118 112 103 95 957 92
PRO22M F/4 1PH 130 125 118 110 1046 92.1
• IP23 PROTECTION • COMPACT AND MECHANICALLY RESISTANT • EXCELLENT WAVE FORM• MINIMUM MAINTENANCE• HIGH EFFICIENCY• WITH AUXLIARY WINDING (see page 10)• UL RECOGNIZED INSULATION SYSTEM (Standards: UL 1446, Systems of Insulating Materials -
General CSA-C22.2 No. 0, Appendix B, General Requirements - Canadian Electrical Code, Part II)• cCSAus CERTIFICATION (Standards: CAN/CSA –C22.2 No. 100-14 (R2009) Motors and Generators,
UL1004-1 2nd ed. Rotating Electrical Machines–General Requirements, UL1004-4 2nd ed. Electric Generators)
• For overall dimensions see from page 26 to 30INSULATION SYSTEM 250H
E1X13
• Brushless synchronous alternators with AVR • Dedicated Single-phase• 1 Power Factor• Class H Insulation• With Auxiliary Winding
60HZ - SINGLE PHASE4 POLE / 1800 RPMBRUSHLESS WITH AVR
-
10 For more information and support contact: T.+1 (847) 595 1473 - [email protected] - www.linzelectric.us
MECHANICAL CHARACTERISTICSE1X, SL and PRO series are compact, durable and mechanically resistant. The casing, front and rear shields are made of vibration resistant aluminium alloy and steel. The shafts are made of high resistant steel and the bearings are lifelong lubricated. Rotors are extremely strong in order to resist the escape velocity of the drive engines and they are equipped with a damping cage to ensure excellent performance even during single-phase distorting and unbalanced three-phase loads.All standard motor couplings used in the market are available.
ELECTRICAL FEATURESThe rotor and stator insulation is made of class H materials and the winding is tropicalised. The magnetic lamination is low loss rate to ensure maximum performance.
WINDINGS: All windings are all made of class H materials. The quality of the copper undergoes a double check to guarantee the very best standard in the market.Three-phase 12 leads windings are wound to 2/3 pitch to reduce the total harmonic voltage distortion by keeping it constantly within 3% during all electrical function conditions.
DAMPING CAGE: Every model in the E1X, SL and PRO series has a damping cage as standard which allows the alternator to work in parallel stand-alone or connected to the grid and operating with single-phase distorting and unbalanced three-phase loads. The damping cage on all the models provides added value since the market for applications using electronic loads is growing rapidly (UPS , inverter, chopper and switching power supply units). These loads need to be managed by power switching devices with a good quality voltage wave form even when loaded.
AUXILIARY POWER WINDING: The important aim of the auxiliary winding function is to guarantee that the power supply to the electronic regulator is not affected by the load connected to the generator. This winding ensures that the regulator operates perfectly whatever the load type, even with a severe non-linear load.The auxiliary winding is galvanically insulated and independent of the main windings. It has been dimensioned to guarantee a permanent short-circuit current equal to 3 times the rated current for at least 10 seconds, thus providing optimal function during heavy start-up transients of asynchronous motors.This auxiliary winding is the technological answer to the PMG (permanent magnet generator) power supply system, used in the past to support short circuit current, a function that this special auxiliary winding now carries out perfectly.
OVERLOADS AND SHORT CIRCUIT CURRENT: Overload of 10% of the rated power for 1 hour every 6 hours is allowed.In case of a three-phase symmetric short circuit, the permanent current is, on average, 300% of the rated current. This value can be sustained for 10 seconds.
THD (TOTAL HARMONIC DISTORTION): With linear and balanced load is less than 3% with or without load (L-L and L-N)
ELECTRONIC REGULATORS: The voltage regulators are designed, manufactured and tested entirely in our factories. They are made with state-of-the-art electronic components and technologies that ensure reliability and sturdiness under any generator working conditions. Two models are available: single phase voltage reference model HVR-11 and three-phase voltage reference HVR-30 with three separate inputs. The standard E1X-SL-PRO alternators series include the following electronic regulators: HVR-11 on E1X, SL, PRO18 and PRO22 (HVR30 is supplied on request) and HVR-30 on PRO28, PRO35 and PRO40.
Main features of the regulators- Voltage adjustment within the limit of ±1%- Stability control adjustment to guarantee the best dynamic response for any situation (type of drive motor or alternator size) - Output voltage adjustment - Adjustment of the low frequency protection - Adjustment of the over-excitation protection setting caused by abnormal loads- Remote potentiometer inlet - 50Hz or 60Hz working possibility- Parallel operation with a specific kit (DP01) All adjustments are made with multi-turn trimmers that allow an extremely accurate setting.
TECHNICAL FEATURES E1X-SL-PRO
-
11For more information and support contact: T.+1 (847) 595 1473 - [email protected] - www.linzelectric.us
PD (PARALLEL DEVICE/DROP DEVICE): This device is recommendend for paralleling two or more alternators. Furthermore, our AVR are equipped with a (0-5)Vdc input to connect external governors running parallel operation. ANTI-CONDENSATION HEATERS: Anti-condensation heaters, specifically made to apply onto the main stator during the winding final stage production, are available for the entire PRO series.
IMPREGNATIONS FOR MARINE USE: The main stator of all E1X, SL and PRO alternators undergoes a standard treatment with a red paint: a protective class F high temperature insulating enamel phenolic resin that can be applied to all the generator wound parts forming a flexible film with excellent mechanical, heat and chemical resistance. It is suggested for use in high humidity or salinity environments.
Characteristics of red phenolic resin:• Excellent chemical resistance to water, salt mineral and acids• Oil and moisture restistant• Thermal class: 175°C• Excellent heat resistance
THERMAL PROBES: On request, thermal capsules with an NC switch (normally closed) and PT100 probes can be fitted into the windings. The PRO35 series comes complete with bimetallic thermal protectors.
GEAR BOXES: The E1X, PRO18 and PRO22 series can be supplied with gear box for PTO drive.
SUPPRESSION OF RADIO INTERFERENCE: all our products comply with the EN55014-1, EN55011 and VDE0875 directives, guaranteeing a grade G and N level. Moreover, radio interference filters are available in order to match the requirements of the most restrictive norms.
ACCESSORIES E1X13 SLS-SLT PRO18 PRO22 PRO28 PRO35-PRO40
B3/B14 mounting form • n.a. • • • •
Gear box • n.a. • • n.a. n.a.
Impregnation for marine environment • • • • • •
Regulator HVR30 n.a. n.a. • • std. std.
Device for parallel operations n.a. n.a. • • • std.
EMI filter • • • • • std.
Anticondensation heaters • • • • • •
Bimetallic thermal protections • • • • • std.
PT100 for bearings • • • • • •
PT100 for windings • • • • • •
PMG n.a. n.a. n.a. n.a. • •
ACCESSORIES FOR E1X-SL-PRO
• n.a.: not available for this model• std.: available and no overprice for this option on this model
-
12 For more information and support contact: T.+1 (847) 595 1473 - [email protected] - www.linzelectric.us
MODEL
3 Phase 127/220V or 220/380V
kVANet weight SAE
(lbs)Eff%
cosφ = 0.8150/40 125/40 105/40 80/40
E1S1
3/4
E1S13S A/4 10.3 9.6 9 8 128 81.4
E1S13S B/4 13 12 11 9.6 142 83.5
E1S13M D/4 16.5 16 14.5 12.6 171 85
E1S13M E/4 21 19 17.5 15 200 86.3
E1S13M F/4 26 24 22 19 207 86.5
TECHNICAL FEATURES
E1S13/4 series are three-phase 4 pole alternators with brushes and compound voltage transformer regulation. This series has been designed for applications requiring high start-up capability of inductive loads such as electric motors, electric water pumps, air compressors.
VOLTAGE: Standard 220/380V or 127/220 V at 60 Hz . Special voltage on request.
VOLTAGE ACCURACY: ± 4% froload to full load, cosφ = 0.8 at constant rotation speed.
SHORT CIRCUIT CURRENT: In case of short circuit the permanent current is 350% of the rated current. This value can be sustained for 10 seconds.
OVERLOAD: 10% overload for one hour every 6 hours is accepted. Short overloads can be very high (three times the rated current).
ASYNCHRONOUS MOTORS STARTING: 1 HP per kVA of the generator can be started.
OUTPUT VOLTAGE WAVE FORM: The low harmonic content (
-
13For more information and support contact: T.+1 (847) 595 1473 - [email protected] - www.linzelectric.us
• MECHANICALLY RESISTANT • MINIMUM MAINTENANCE• UL RECOGNIZED INSULATION SYSTEM (Standards: UL 1446, Systems of Insulating Materials - General CSA-C22.2 No. 0, Appendix B, General Requirements - Canadian
Electrical Code, Part II)• cCSAus CERTIFICATION (Standards: CAN/CSA –C22.2 No. 100-14 (R2009) Motors and Generators, UL1004-1 2nd ed. Rotating Electrical Machines–General Requirements,
UL1004-4 2nd ed. Electric Generators)
• For overall dimensions see from page 34 to 35
MODEL
Single Phase120/240V - Series Parallel
kVANet weight SAE
(lbs)Eff%
cosφ = 1150/40 125/40 105/40 80/40
E1C1
3/4
E1C13S A/4 7.5 7 6.5 5.5 113 81.7
E1C13S B/4 9.3 8.5 7.5 6.5 127 82
E1C13S C/4 10.5 9.75 8.8 7.5 141.5 82.6
E1C13S D/4 12 11 10 8.5 151 82.8
E1C13M E/4 14.5 14 12.5 11 184.5 83
E1C13M F/4 16 15 13 11.5 192 83.2
TECHNICAL FEATURES
E1C13/4 series are single-phase 4 poles brushless alternators with an auxiliary winding loaded onto highly insulated dielectric capacitors regulating the voltage. This series has been designed for single-phase generating sets and lighting towers.
VOLTAGE ACCURACY: ± 5% from no load to full load, cosφ =1 at constant rotation speed.
SHORT CIRCUIT CURRENT: In case of short circuit the permanent current exceeds rated current by three times, ensuring the correct operation of protections.
OVERLOAD: A 10% overload for one hour every 6 hours is accepted.
TRANSIENT VOLTAGE DIP AT RATED LOAD INSERTION: The voltage dip when the load is inserted is lower than 10% at cosφ =1 and nominal rpm.
INSULATION SYSTEM 250H
E1C13
60HZ - SINGLE PHASE4 POLE / 1800 RPMBRUSHLESS WITH CAPACITOR
• Brushless Synchronous Alternators With Capacitor
• 1 Power Factor• Class H Insulation
-
REFERENCE STANDARDSOur alternators are built in accordance with the provisions specified in the :• EN 60034-1, EN 60204-1, EN61000-6-2, EN61000-6-4, EN 55014-1, EN 55011 standards • 2006/95/CE and 2004/108/CE directives• cURus - Recognized insulation system under UL1446 standard (file number E481753)
E1X, SL, PRO18,PRO22, E1C13/4 series are listed by CSA Group as certified (cCSAus - CAN/CSA - C22.2 No.100-14 ) and are also built in accordance with UL 1004-1 and UL1004-4 (file number 260717)
OPERATING CONDITIONSThe performance data reported in the present catalogue are valid for operation at an altitude not exceeding 1000m (3300 ft) and ambient temperature not exceeding 40°C (104°F). If operation takes place in different conditions, consult the table below.
14 For more information and support contact: T.+1 (847) 595 1473 - [email protected] - www.linzelectric.us
Power variation according to temperature and altitude
ALTITUDE m / ft
Ambient temperature25 °C / 77°F 40 °C / 104°F 45 °C / 113°F 50 °C / 122°F 55 °C / 131°F
< 1000 / 3300
1.09 1 0.96 0.93 0.91
1000-1500 / 3300-4900
1.01 0.96 0.92 0.89 0.87
1500-2000 /4900-6600
0.96 0.91 0.87 0.84 0.83
2000-3000 / 6600-9900
0.9 0.85 0.81 0.78 0.76
GENERAL FEATURES
-
2-POLE ALTERNATORS
-
16 For more information and support contact: T.+1 (847) 595 1473 - [email protected] - www.linzelectric.us
MODEL
3 Phase277/480V - High WYE 138/240V - Low WYE
kVA
3 Phase 240/416V- High WYE 120/208V - Low WYE
kVA
Single Phase120/240V - Series Parallel
kVA
Net weight SAE (lbs)
150/40 125/40 105/40 80/40 150/40 125/40 105/40 80/40 150/40 125/40 105/40 80/40
E1X1
3/2
E1X13S A/2 11 10 9.2 8 9.8 9 8.2 7.5 6.3 5.5 5 4.5 134
E1X13S B/2 13.5 12.5 11.5 10 12 11 10 8.7 7.5 7 6.5 5.7 145.5
E1X13S C/2 16.4 15 14 12 14 13 12 10.5 9 8.5 8 7 161
E1X13M D/2 21 19.5 18 16 18.2 17 15.5 14 11.5 11 10 9 198.5
E1X13M E/2 28 26 24 21 24.5 23 21 18.5 16 15 13.7 12 223
• COMPACT AND MECHANICALLY RESISTANT • EXCELLENT WAVE FORM• MINIMUM MAINTENANCE• HIGH EFFICIENCY• WITH AUXLIARY WINDING (see page 10)• UL RECOGNIZED INSULATION SYSTEM (Standards: UL 1446, Systems of Insulating Materials - General CSA-C22.2 No. 0, Appendix B, General Requirements - Canadian
Electrical Code, Part II)• cCSAus CERTIFICATION (Standards: CAN/CSA –C22.2 No. 100-14 (R2009) Motors and Generators, UL1004-1 2nd ed. Rotating Electrical Machines–General Requirements,
UL1004-4 2nd ed. Electric Generators)
• For overall dimensions see from page 26 to 27
MODEL Leads
3 Phase277/480V - High WYE
138/240 - Low WYE60 Hz - 1800 rpm - cosφ = 0.8
125/40kVA eff.%
E1X13S A/2 12 10 80.6
E1X13S B/2 12 12.5 82
E1X13S C/2 12 15 83.4
E1X13M D/2 12 19.5 85.5
E1X13M E/2 12 26 86.2
EFFICIENCY TABLE
60HZ - THREE PHASE2 POLE / 3600 RPMBRUSHLESS WITH AVR
• Brushless synchronous alternators with AVR• 0.8 Power Factor• Class H Insulation• 12 Leads• With Auxiliary Winding
INSULATION SYSTEM 250H
E1X13
-
17For more information and support contact: T.+1 (847) 595 1473 - [email protected] - www.linzelectric.us
MODEL
Single Phase120/240V - Series Parallel
kVANet weight SAE
(lbs)Eff%
cosφ = 1150/40 125/40 105/40 80/40
E1X1
3/2 1
PH
E1X13S A/2 8 7.5 7 6.5 134 80.5
E1X13S B/2 9.7 9 8.4 7.8 145.5 81.5
E1X13S C/2 13 12 11 10 161 84.2
E1X13M D/2 16 15 14 13 198.5 86
E1X13M E/2 21.5 20 18.5 17.5 222.5 86.8
• COMPACT AND MECHANICALLY RESISTANT • EXCELLENT WAVE FORM• MINIMUM MAINTENANCE• HIGH EFFICIENCY• WITH AUXLIARY WINDING (see page10)• UL RECOGNIZED INSULATION SYSTEM (Standards: UL 1446, Systems of Insulating Materials - General CSA-C22.2 No. 0, Appendix B, General Requirements - Canadian
Electrical Code, Part II)• cCSAus CERTIFICATION (Standards: CAN/CSA –C22.2 No. 100-14 (R2009) Motors and Generators, UL1004-1 2nd ed. Rotating Electrical Machines–General Requirements,
UL1004-4 2nd ed. Electric Generators)
• For overall dimensions see from page 26 to 27
60HZ - SINGLE PHASE2 POLE / 3600 RPMBRUSHLESS WITH AVR
• Brushless synchronous alternators with AVR• Dedicated Single-phase• 1 Power Factor • Class H Insulation• With Auxiliary Winding
INSULATION SYSTEM 250H
E1X13
-
18 For more information and support contact: T.+1 (847) 595 1473 - [email protected] - www.linzelectric.us
TECHNICAL FEATURES E1X/2
WINDINGS AND VOLTAGE: all windings are made of Class H materials. A double layer with shortened 2/3 pitch is ensuring a low harmonic content by keeping it constantly within 3% during all electrical function conditions. E1X three phase alternators are equipped with a 12 terminal winding (see page 26 for possible connections and voltages). Special voltages are available on request.
VOLTAGE ACCURACY : ± 1% from no load to full load with Power Factor 0.8 and constant rotation speed.
OVERLOADS AND SHORT CIRCUIT CURRENT: Overload of 10% of the rated power for 1 hour every 6 hours is allowed. In case of a three-phase symmetric short circuit, the permanent current is, on average, 300% of the rated current. This value can be sustained for 10 seconds.
THD (TOTAL HARMONIC DISTORTION): With linear and balanced load is less than 3% with or without load (L-L and L-N)
ELECTRONIC REGULATION : E1X series is equipped with the last generation of the HVR11 electronic regulation. All adjustments are made with multi-turn trimmers that allow an extremely accurate setting.The main features of the regulator are:- Output voltage adjustment within the limit of ±1%- Stability control adjustment to guarantee the best dynamic response for any situation (type of drive motor or alternator size)- Adjustment of the low frequency protection- Adjustment of the over-excitation protection setting caused by abnormal loads- Remote potentiometer inlet- 50Hz or 60Hz working possibility.
-
19For more information and support contact: T.+1 (847) 595 1473 - [email protected] - www.linzelectric.us
MODEL
Single Phase120/240V - Series Parallel
kVANet weight
(lbs)Eff%
cosφ = 1150/40 125/40 105/40 80/40
SP10
SP10S A 2.2 2 1.8 1.6 25 73.5
SP10S B 3 2.7 2.4 2.1 29.8 74.5
SP10S C 3.5 3.2 2.9 2.5 33 75.5
SP10S D 4 3.7 3.3 2.9 36 76
SP10S E 4.7 4.3 3.9 3.4 39 76.5
SP10M F 5.5 5 4.7 4.1 43.6 77
SP10M G 6.6 6 5.5 4.8 46.3 77.5
MODEL
Single Phase120/240V - Series Parallel
kVANet weight
(lbs)Eff%
cosφ = 1150/40 125/40 105/40 80/40
E1C1
0
E1C10S B 3 2.7 2.4 2.1 34.8 74.5
E1C10S D 4 3.7 3.3 2.9 39.7 76
E1C10S E 4.7 4.3 3.9 3.4 44 76.5
E1C10S F 5.5 5 4.7 4.1 47 77
E1C10S G 6.6 6 5.5 4.8 50.7 77.5
E1C10M H 7.9 7.25 6.8 6 64.6 79
E1C10M I 9.3 8.5 8 7 71.2 80.5
E1C10M L 10.5 9.75 9 7.8 81.0 79.5
E1C1
1 E1C11M B 13.7 12.5 11.5 10 105.4 80E1C11M C 16.4 15 13 11.5 115 80.5
E1C13
/2 E1C13M D/2 20 18 17 15 170.6 81.5E1C13M E/2 24 22 20 17.5 195 82.1
• COMPACT AND MECHANICALLY RESISTANT • EXCELLENT WAVE FORM• MINIMUM MAINTENANCE• HIGH EFFICIENCY• UL RECOGNIZED INSULATION SYSTEM (Standards: UL 1446, Systems of Insulating Materials - General CSA-C22.2 No. 0, Appendix B, General Requirements - Canadian
Electrical Code, Part II)• cCSAus CERTIFICATION (Standards: CAN/CSA –C22.2 No. 100-14 (R2009) Motors and Generators, UL1004-1 2nd ed. Rotating Electrical Machines–General Requirements,
UL1004-4 2nd ed. Electric Generators)• For overall dimensions see from page 34 to 40
INSULATION SYSTEM 250H
INSULATION SYSTEM 250H
SP10
E1C10
60HZ - SINGLE PHASE2 POLE / 3600 RPMBRUSHLESS WITH CAPACITOR
• Brushless synchronous alternators with capacitor
• 1 Power Factor • Class H Insulation
-
20 For more information and support contact: T.+1 (847) 595 1473 - [email protected] - www.linzelectric.us
SP and E1C series are single-phase 2 poles brushless alternators with an auxiliary winding loaded onto highly insulated dielectric capacitors regulating the voltage. This series has been designed for portable single-phase generating sets and lighting towers .
VOLTAGES: standard 120/240V, 60Hz. Special voltages on request.
VOLTAGE ACCURACY: ± 5% from no load to full load, cosφ =1 at constant rotation speed.
SHORT CIRCUIT CURRENT: In case of short circuit the permanent current exceeds rated current by three times, ensuring the correct operation of protections.
OVERLOAD: A 10% overload for one hour every 6 hours is accepted.
OUTPUT VOLTAGE WAVE FORM: The low harmonic content (
-
21For more information and support contact: T.+1 (847) 595 1473 - [email protected] - www.linzelectric.us
MODEL
3 Phase 127/220V or 220/380V
kVANet weight
(lbs)Eff%
cosφ = 0.8150/40 125/40 105/40 80/40
E1S1
0
E1S10M G 7.7 7 6.5 5.7 63.3 79
E1S10M H 9.3 8.5 8 7 73 81
E1S10M I 12 11 10 9 81.4 82.5
E1S10L L 13 12 11 9.7 91.3 82.7
E1S1
1 E1S11M AS 15 14 13 11.5 100 83.5E1S11M B 18 16.5 15.5 13.6 113.5 84
E1S1
3 E1S13S C/2 21 19.2 17.5 15.5 134.5 85.5E1S13M D/2 28 26.4 24 21 170.6 86.5
E1S13M E/2 35 32.4 29.5 26 195 87.5
• COMPACT AND MECHANICALLY RESISTANT • EXCELLENT WAVE FORM• HIGH STARTING CAPACITY OF INDUCTIVES LOADS• HIGH EFFICIENCY• UL RECOGNIZED INSULATION SYSTEM (Standards: UL 1446, Systems of Insulating Materials - General CSA-C22.2 No. 0, Appendix B, General Requirements - Canadian
Electrical Code, Part II)
• For overall dimensions see pages 34, 35, 41 and 42
TECHNICAL FEATURES E1SE1S/2 series are three-phase 2 pole alternators with brushes and compound voltage transformer regulation. This series has been designed for applications requiring high start-up capability of inductive loads such as electric motors, electric water pumps, air compressors.
VOLTAGE: Standard 220/380 or 127/220 at 60Hz. Special voltage on request.
VOLTAGE ACCURACY: ± 4% from no load to full load, PF 0.8 at constant rotation speed.
SHORT CIRCUIT CURRENT: In case of short circuit the permanent current is 350% of the rated current. This value can be sustained for 10 seconds.
OVERLOAD: 10% overload for one hour every 6 hours is accepted.
ASYNCHRONOUS MOTOR STARTING: 1 HP per kVA of the generator can be started.
THD (TOTAL HARMONIC DISTORTION): With linear and balanced load is less than 5% with or without load (L-L and L-N) and allows supplying any type of load, including distorting loads.
INSULATION SYSTEM 250H
E1S13
60HZ - THREE PHASE2 POLE / 3600 RPMWITH BRUSHES AND COMPOUND
• Brush Synchronous Alternators With Transformer Regulation/Compound
• 0.8 Power Factor• Class H Insulation• 6 Leads
-
22 For more information and support contact: T.+1 (847) 595 1473 - [email protected] - www.linzelectric.us
MODEL
3 Phase127/220V or 220/380V
kVA-Net weight
(lbs)Eff%
cosφ = 0.8150/40 125/40 105/40 80/40
E1S1
0 - KE
E1S10M G-KE 6 5.4 5 4.7 63.3 79
E1S10M H-KE 7.5 7 6.3 5.8 73 81
E1S10M I-KE 9.3 8.5 7.8 7 81.4 82.5
E1S10L L-KE 12 11 10 9 92.8 82.8
E1S11
-KE E1S11M AS-KE 13.2 12.5 11.5 10.5 100 83.7
E1S11M B-KE 15 14 12.8 11.8 113.5 84
TECHNICAL FEATURES
E1S KE series are three-phase 2 pole alternators with brushes and a double voltage regulation: Electronic (AVR) and voltage transformer regulation (COMPOUND). This series has been designed for applications requiring high start-up capability of inductive loads such as electric motors, electric water pumps, air compressors thus maintaining a voltage accuracy of +/1%.The “KE” system, envisaging the combined use of a compound and an electronic regulation, solves the typical inconveniences of an exclusively compound or electronic regulation. The electronic regulator has an ad-hoc delayed load insertion time to allow the compound to act during the transient voltage dip. After that period of time, the electronic regulation resumes the operations by correcting the output voltage. The generator can operate with both the compound regulation alone and the electronic regulation alone, increasing the reliability of the machine in case of failure of one of the two systems.
VOLTAGE: Standard 220/380 or 127/220 at 60Hz. Special voltage on request.
VOLTAGE ACCURACY: ± 1% from no load to full load, PF 0.8 at constant rotation speed.
SHORT CIRCUIT CURRENT: In case of short circuit the permanent current is 350% of the rated current. This value can be sustained for 10 seconds.
OVERLOAD: 10% overload for one hour every 6 hours is accepted.
ASYNCHRONOUS MOTOR STARTING: 1 HP per kVA of the generator can be started.
THD (TOTAL HARMONIC DISTORTION): With linear and balanced load is less than 5% with or without load (L-L and L-N) and allows supplying any type of load, including distorting loads.
• COMPACT AND MECHANICALLY RESISTANT• EXCELLENT WAVE FORM• HIGH STARTING CAPACITY OF INDUCTIVES LOADS AND ±1% VOLTAGE REGULATION• HIGH EFFICIENCY• UL RECOGNIZED INSULATION SYSTEM (Standards: UL 1446, Systems of Insulating Materials - General CSA-C22.2 No. 0, Appendix B, General Requirements - Canadian
Electrical Code, Part II)
• For overall dimensions see from page 41 to 42
INSULATION SYSTEM 250H
E1S10
60HZ - THREE PHASE2 POLE / 3600 RPMBRUSHES AVR AND COMPOUND
• Brush Synchronous Alternators With Mixed Regulation (AVR + COMPOUND)
• 0.8 Power Factor• Class H Insulation• 6 Leads
-
23For more information and support contact: T.+1 (847) 595 1473 - [email protected] - www.linzelectric.us
GENERAL FEATURES
MECHANICAL SPECIFICATIONSThe SP and E1 series are manufactured by means of advanced technology and high quality materials. The frame is made of vibration-resistant aluminum alloy. The shaft is in high tensile steel. The rotor is designed to resist the runaway speed of the traction motors. The bearings are life-long lubricated. Axial ventilation is ensured with intake from the side opposite to the coupling. Both rotation directions are possible.All the motor coupling standards available on the market are supported.
ELECTRICAL FEATURESInsulation is obtained with H class material for both stator and rotor and the windings are tropicalized. Low-loss lamination is used.
REFERENCE STANDARDSOur alternators series are built in accordance with the provisions specified in the :• EN 60034-1, EN 60204-1, EN 61000-6-2, EN 61000-6-4, EN 55014-1, EN 55011 standards• 2006/95/CE and 2004/108/CE directives• cUR us - Recognized insulation system under UL1446 standard (file number E481753)SP , E1C and E1X13/2 series are listed by CSA Group as certified (cCSA us - CAN /CSA - C22.2 No.100-14 ) and are also built in accordance with UL 1004-1 and UL 1004-4 (file number 260717).
OPERATING CONDITIONSThe performance data reported in the present catalogue are valid for operation at an altitude not exceeding 1000m (3300 ft) and ambient temperature not exceeding 40°C (104°F). If operation takes place in different conditions, consult the table below.
Power variation according to temperature and altitude
ALTITUDE m / ft
Ambient temperature25 °C / 77°F 40 °C / 104°F 45 °C / 113°F 50 °C / 122°F 55 °C / 131°F
< 1000 / 3300
1.09 1 0.96 0.93 0.91
1000-1500 / 3300-4900
1.01 0.96 0.92 0.89 0.87
1500-2000 /4900-6600
0.96 0.91 0.87 0.84 0.83
2000-3000 / 6600-9900
0.9 0.85 0.81 0.78 0.76
-
24 For more information and support contact: T.+1 (847) 595 1473 - [email protected] - www.linzelectric.us
Series High WYE (Series Star)
Parallel Low WYE (Parallel Star)
Series Delta
Parallel Delta
Zig-Zag
Double Delta (single phase connection)
12 LEADS
CONNECTIONS TO THE TERMINAL BOARD
Hz L-N L-L
60 240 - 415
254 - 440
266 - 460
277 - 480
50 220 - 380
230 - 400
240 - 415
254 - 440
Hz L-N L-L
60 120 - 208
127 - 220
133 - 230
139 - 240
50 110 - 190
115 - 200
120 - 208
127 - 220
Hz L-N L-L
60 240
254
266
277
50 220
230
240
254
Hz L-N L-L
60 120
127
133
139
50 110
115
120
127
Hz L-N L-L
60 208 - 360
220 - 380
230 - 400
240 - 415
50 191 - 330
200 - 346
208 - 360
220 - 380
Hz L-M L-L
60 120 - 240
127 - 254
133 - 266
139 - 277
50 110 - 220
115 - 230
120 - 240
127 - 254
-
25For more information and support contact: T.+1 (847) 595 1473 - [email protected] - www.linzelectric.us
CONNECTIONS TO THE TERMINAL BOARD
Series High WYE (Series Star)
Series Delta
6 LEADS
Hz L-N L-L
60 240 - 415
254 - 440
266 - 460
277 - 480
50 220 - 380
230 - 400
240 - 415
254 - 440
Hz L-N L-L
60 240
254
266
277
50 220
230
240
254
-
TECHNICAL DRAWINGS AND DIMENSIONS E1X13S
26 For more information and support contact: T.+1 (847) 595 1473 - [email protected] - www.linzelectric.us
-
TECHNICAL DRAWINGS AND DIMENSIONS E1X13M
27For more information and support contact: T.+1 (847) 595 1473 - [email protected] - www.linzelectric.us
-
TECHNICAL DRAWINGS AND DIMENSIONS SLS-SLT
28 For more information and support contact: T.+1 (847) 595 1473 - [email protected] - www.linzelectric.us
-
TECHNICAL DRAWINGS AND DIMENSIONS PRO18
29For more information and support contact: T.+1 (847) 595 1473 - [email protected] - www.linzelectric.us
-
TECHNICAL DRAWINGS AND DIMENSIONS PRO22
30 For more information and support contact: T.+1 (847) 595 1473 - [email protected] - www.linzelectric.us
-
TECHNICAL DRAWINGS AND DIMENSIONS PRO28
31For more information and support contact: T.+1 (847) 595 1473 - [email protected] - www.linzelectric.us
-
TECHNICAL DRAWINGS AND DIMENSIONS PRO35
32 For more information and support contact: T.+1 (847) 595 1473 - [email protected] - www.linzelectric.us
-
TECHNICAL DRAWINGS AND DIMENSIONS PRO40
33For more information and support contact: T.+1 (847) 595 1473 - [email protected] - www.linzelectric.us
-
TECHNICAL DRAWINGS AND DIMENSIONS E1C13S-E1S13S
34 For more information and support contact: T.+1 (847) 595 1473 - [email protected] - www.linzelectric.us
-
TECHNICAL DRAWINGS AND DIMENSIONS E1C13M-E1S13M
35For more information and support contact: T.+1 (847) 595 1473 - [email protected] - www.linzelectric.us
-
TECHNICAL DRAWINGS AND DIMENSIONS SP10
36 For more information and support contact: T.+1 (847) 595 1473 - [email protected] - www.linzelectric.us
-
TECHNICAL DRAWINGS AND DIMENSIONS SP10
37For more information and support contact: T.+1 (847) 595 1473 - [email protected] - www.linzelectric.us
-
TECHNICAL DRAWINGS AND DIMENSIONS E1C10S
38 For more information and support contact: T.+1 (847) 595 1473 - [email protected] - www.linzelectric.us
-
TECHNICAL DRAWINGS AND DIMENSIONS E1C10M
39For more information and support contact: T.+1 (847) 595 1473 - [email protected] - www.linzelectric.us
-
TECHNICAL DRAWINGS AND DIMENSIONS E1C11
40 For more information and support contact: T.+1 (847) 595 1473 - [email protected] - www.linzelectric.us
-
TECHNICAL DRAWINGS AND DIMENSIONS E1S10M-L
41For more information and support contact: T.+1 (847) 595 1473 - [email protected] - www.linzelectric.us
-
TECHNICAL DRAWINGS AND DIMENSIONS E1S11
42 For more information and support contact: T.+1 (847) 595 1473 - [email protected] - www.linzelectric.us
-
60HZ ALTERNATORS PRODUCTS CATALOG 2020_rev.1 / LINZ ELECTRIC Inc. reserves the right to implement modifications.
-
44 For more information and support contact: T.+1 (847) 595 1473 - [email protected] - www.linzelectric.us
Find us on:North American Subsidiary:LINZ ELECTRIC INC.3005 Commercial Ave.Northbrook, IL 60062 - USAT.+1 (847) 595 [email protected]
Manufacturer:LINZ ELECTRIC S.P.A. Viale del lavoro 3037040, Arcole (Verona), Italy T.+39 (045) 7639 [email protected]