5C EMP and EMPS Barrel Cl. I, Div. 1 & 2, Groups B, C, D … · 2020. 12. 23. · All barrel...
3
5C 584 www.crouse-hinds.com US: 1-866-764-5454 CAN: 1-800-265-0502 Copyright © 2013 Eaton’s Crouse-Hinds Business 5C EMP and EMPS Barrel Assemblies Cl. I, Div. 1 & 2, Groups B, C, D Cl. II, Div. 1, Groups E, F, G Cl. II, Div. 2, Groups F, G Cl. III II 2 G Ex d IIB + H2, T5 Explosionproof Dust-Ignitionproof Raintight Wet Locations NEMA 3, 7BCD, 9EFG As indicated in the listings, certain barrel assemblies are the same as those used in complete EMP units and may be utilized as replacements. The remainder are primarily for use with hazardous area boxes to assemble special control stations. For additional information, see pages 576–583 describing custom- built control panels. Certifications and Compliances: • Class I, Division 1 & 2, Groups B, C, D • Class II, Division 2, Groups E, F, G • Class III • NEMA/EEMAC: 3, 7BCD, 9EFG • UL Standard 1203 • CSA Standard C22.2 No 30 • CENELEC • ATEX Certificate ITS07 ATEX 15652U Ordering Information: Select the Cat. No. from the listings. For pilot lights and illuminated pushbuttons, specify color of jewel using symbols from the table below. For pushbuttons and selector switches, optional markings may be specified in the tables below. Group 1: Standard assemblies are for replacement in complete EMP units or for custom-built control panels. Short assemblies are for custom-built control panels only. Both assemblies may be used with System 4 Control Stations. Pilot light‡ Diagram Standard Assembly Cat. # (120V)* EMP009 ➀ Single pushbutton Double pushbutton, single operator Diagram Short Cat. # Standard Cat. # EMPS019 ➁ EMP019 ➁ EMPS029 ➁ EMP029 ➁ Double pushbutton, double operator Diagram Short Assembly Cat. # Standard Assembly Cat. # EMPS039 ➁ EMP039 ➁ Two-position selector switch Diagram Short Assembly Standard Assembly Position 1 Position 2 Cat. # Cat. # EMPS049 ➁ EMP049 ➁ EMPS059 ➁ EMP059 ➁ Three-position selector switch Diagram Short Assembly Standard Assembly ✠ Position 1 Position 2 Position 3 Cat. # Cat. # EMPS069 ➁ EMP069 ➁ EMPS079 ➁ EMP079 ➁ EMPS089 ➁ EMP089 ➁ ➀Add color symbol for each pilot light from table below. Color Symbol Color Symbol Red J1 Clear J10 Green J3 Blue J11 Amber J6 ➁If desired, markings on indicating plates may be added to catalog number. Select from the list of standard markings below: Push Button Station Marking START OFF RESET LIGHT ON EMERGENCY OPEN DOWN RAISE STOP RUN TRIP HAND FORWARD CLOSE IN LOWER ON JOG TEST AUTOMATIC REVERSE UP OUT ‡ LED pilot lights can be furnished in place of standard incandescent pilot lamps. Add suffix LED to end of catalog number after last color symbol. * Other voltages available. Consult factory. For 24 VDC operation, add suffix S300. ✠ The following suffixes may be used with these catalog numbers: S634 - Momentary contact clockwise, spring return to center; S635 - Momentary contact counter-clockwise, spring return to center.
Transcript of 5C EMP and EMPS Barrel Cl. I, Div. 1 & 2, Groups B, C, D … · 2020. 12. 23. · All barrel...
-
5C
584 www.crouse-hinds.com US: 1-866-764-5454 CAN: 1-800-265-0502 Copyright© 2013 Eaton’s Crouse-Hinds Business
5C EMP and EMPS BarrelAssemblies
Cl. I, Div. 1 & 2, Groups B, C, DCl. II, Div. 1, Groups E, F, GCl. II, Div. 2, Groups F, GCl. IIIII 2 G Ex d IIB + H2, T5
ExplosionproofDust-IgnitionproofRaintightWet LocationsNEMA 3, 7BCD, 9EFG
As indicated in the listings, certain barrelassemblies are the same as those used incomplete EMP units and may be utilized asreplacements.
The remainder are primarily for use withhazardous area boxes to assemble specialcontrol stations. For additional information,see pages 576–583 describing custom-built control panels.
Certifications andCompliances:• Class I, Division 1 & 2, Groups B, C, D• Class II, Division 2, Groups E, F, G• Class III• NEMA/EEMAC: 3, 7BCD, 9EFG• UL Standard 1203• CSA Standard C22.2 No 30• CENELEC• ATEX Certificate ITS07 ATEX 15652U
Ordering Information:Select the Cat. No. from the listings. Forpilot lights and illuminated pushbuttons,specify color of jewel using symbols fromthe table below. For pushbuttons andselector switches, optional markings maybe specified in the tables below.
Group 1:Standard assemblies are for replacementin complete EMP units or for custom-builtcontrol panels. Short assemblies are forcustom-built control panels only. Bothassemblies may be used with System 4Control Stations.
Pilot light‡
Diagram
StandardAssemblyCat. #
(120V)* EMP009 ➀
Single pushbutton Double pushbutton, single operator
DiagramShortCat. #
StandardCat. #
EMPS019 ➁ EMP019 ➁
EMPS029 ➁ EMP029 ➁
Double pushbutton, double operator
Diagram
ShortAssemblyCat. #
StandardAssemblyCat. #
EMPS039 ➁ EMP039 ➁
Two-position selector switch
DiagramShortAssembly
StandardAssembly
Position 1 Position 2 Cat. # Cat. #
EMPS049 ➁ EMP049 ➁
EMPS059 ➁ EMP059 ➁
Three-position selector switch
DiagramShortAssembly
StandardAssembly ✠
Position 1 Position 2 Position 3 Cat. # Cat. #
EMPS069 ➁ EMP069 ➁
EMPS079 ➁ EMP079 ➁
EMPS089 ➁ EMP089 ➁
➀Add color symbol for each pilot light fromtable below.Color Symbol Color SymbolRed J1 Clear J10Green J3 Blue J11Amber J6
➁If desired, markings on indicating plates may be added to catalog number. Select from thelist of standard markings below: Push Button Station MarkingSTART OFF RESET LIGHT ON EMERGENCY OPEN DOWN RAISESTOP RUN TRIP HAND FORWARD CLOSE IN LOWERON JOG TEST AUTOMATIC REVERSE UP OUT
‡ LED pilot lights can be furnished in place of standard incandescent pilot lamps. Add suffix LED to end of catalog numberafter last color symbol.* Other voltages available. Consult factory. For 24 VDC operation, add suffix S300.✠ The following suffixes may be used with these catalog numbers: S634 - Momentary contact clockwise, spring return tocenter; S635 - Momentary contact counter-clockwise, spring return to center.
584-585.qxp 12/23/2013 3:09 PM Page 584
-
5C
585www.crouse-hinds.com US: 1-866-764-5454 CAN: 1-800-265-0502 Copyright© 2013 Eaton’s Crouse-Hinds Business
EMP and EMPS BarrelAssemblies
Cl. I, Div. 1 & 2, Groups B, C, DCl. II, Div. 1, Groups E, F, GCl. II, Div. 2, Groups F, GCl. IIIII 2 G Ex d IIB + H2, T5
ExplosionproofDust-IgnitionproofRaintightWet LocationsNEMA 3, 7BCD, 9EFG
Group 2: For custom-builtcontrol panels.
Illuminated pushbutton‡
Diagram
LongAssemblyCat. #
120V pilotlight EMP0090 ➀
120V pilotlight EMP0098 ➀
5C
Two-position selectorswitch, key operated
Diagram
Position 1 Position 2KeyRemoval
ShortAssemblyCat. #
StandardAssemblyCat. #
Both positions EMPS0491 ➁ EMP0491 ➁Left only EMPS0492 ➁ EMP0492 ➁Right only EMPS0493 ➁ EMP0493 ➁
Both positions EMPS0591 ➁ EMP0591 ➁Left only EMPS0592 ➁ EMP0592 ➁Right only EMPS0593 ➁ EMP0593 ➁
Three-position selector switch, key operatedDiagram
Position 1 Position 2 Position 3KeyRemoval
ShortAssemblyCat. #
StandardAssemblyCat. # ✠
All EMPS0691 ➁ EMP0691 ➁Center only EMPS0692 ➁ EMP0692 ➁Left only EMPS0693 ➁ EMP0693 ➁Right only EMPS0694 ➁ EMP0694 ➁
All EMPS0791 ➁ EMP0791 ➁Center only EMPS0792 ➁ EMP0792 ➁Left only EMPS0793 ➁ EMP0793 ➁Right only EMPS0794 ➁ EMP0794 ➁
All EMPS0891 ➁ EMP0891 ➁Center only EMPS0892 ➁ EMP0892 ➁Left only EMPS0893 ➁ EMP0893 ➁Right only EMPS0894 ➁ EMP0894 ➁
Maintained ContactPushbutton
DiagramUp Down
LongAssemblyCat. #
EMP098 ➁
➀Add color symbol for each pilot light from table below.Color Symbol Color SymbolRed J1 Clear J10Green J3 Blue J11Amber J6
➁If desired, markings on indicating plates may be added to catalog number. Select from thelist of standard markings below: Push Button Station MarkingSTART OFF RESET LIGHT ON EMERGENCY OPEN DOWN RAISESTOP RUN TRIP HAND FORWARD CLOSE IN LOWERON JOG TEST AUTOMATIC REVERSE UP OUT
‡ LED pilot lights can be furnished in place of standard incandescent pilot lamps. Add suffix LED to end of catalog number after last color symbol.✠ The following suffixes may be used with these catalog numbers: S634 - Momentary contact clockwise, spring return to center; S635 - Momentary contact counter-clockwise, spring return to center.
584-585.qxp 12/23/2013 3:09 PM Page 585
-
5C
586 www.crouse-hinds.com US: 1-866-764-5454 CAN: 1-800-265-0502 Copyright© 2013 Eaton’s Crouse-Hinds Business
5C
All barrel assemblies are 3/4"-14 NPSM thread size.
Dimensions*In Inches:
EMP009
EMP-EMPS049, 059, 069, 079, 089
EMP-EMPS029
EMP-EMPS039
EMP098
EMP-EMPS019
EMP0090
EMP-EMPS0491, 0591, 0691, 0791, 0891 Series
EMP0098
*Dimensions are approximate, not for construction purposes.
EMP and EMPS BarrelAssemblies
Cl. I, Div. 1 & 2, Groups B, C, DCl. II, Div. 1, Groups E, F, GCl. II, Div. 2, Groups F, GCl. IIIII 2 G Ex d IIB + H2, T5
ExplosionproofDust-IgnitionproofRaintightWet LocationsNEMA 3, 7BCD, 9EFG
586-587.qxp 12/16/2013 4:48 PM Page 586
![WELCOME []...Emp B = $2350 Emp C = $500 Emp C = $3500 Emp D = $1500 Lag Quarter Emp D = $500 Claim filed Emp D = $150 The claimant must have been paid sufficient …](https://static.fdocuments.in/doc/165x107/607bc797dd97122c8938e959/welcome-emp-b-2350-emp-c-500-emp-c-3500-emp-d-1500-lag-quarter.jpg)
