Edition Date: 11-19 Printed in U.S.A Catalog No: SUB580J–8-16-03 Rev/A

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations. Replaces: SUB580J–8-16-02

580J*08-16 LEGACY™ LINE SERIES SINGLE PACKAGE ROOFTOP

GAS HEATING/ELECTRIC COOLING UNITS TWO-STAGE/TWO-CIRCUIT AND

TWO-STAGE/ONE-CIRCUIT COOLINGCAPACITY CONTROL

— PERFORMANCE DATA

— CERTIFIED DIMENSION PRINTS

— CERTIFIED ROOF CURB DETAILS

2

JOB NAME: LOCATION:

BUYER: BUYER PO #: BRYANT#:

UNIT NUMBER: MODEL NUMBER:

PERFORMANCE DATA CERTIFIED BY:

DESCRIPTION580J units are single-packaged electric cooling, gas heating units that are pre-wired and pre-charged with Puron® (R-410A)HFC refrigerant. The units are factory tested in both heating and cooling modes. These units meet the DOE-2018 (Departmentof Energy), ASHRAE (American Society of Heating, Refrigerating, and Air-Conditioning Engineers) 90.1-2016, andIECC-2015* (International Energy Conservation Code) minimum efficiency requirements. Models with two-stage cooling andtwo-circuit design (08-16 sizes) come standard with two-speed indoor fan motor for U.S. installations. Models with two-stagecooling and one-circuit design does not require two-speed fan motor to meet U.S. minimum efficiencies for DOE.

FEATURESStandard Base Unit (United States Models)• Two-stage/two-circuit cooling capacity control on 08-16

models• Two-stage/one-circuit cooling capacity control on 08,

09, and 12 models.• Energy saving two-speed indoor fan motor on two-cir-

cuit (08-16). Required in U.S. installations. Not avail-able or required to meet DOE on 580J*N models 08, 09,and 12

• DOE-2018, ASHRAE 90.1-2016, and IECC-2015energy compliant

• Rated in accordance with AHRI Standard 340/360• Designed in accordance with Underwriters Laboratories

Std 1995• Listed by ETL and ETL-Canada• Non-corrosive composite sloping design; side or center

drain condensate pan. Meets ASHRAE Standard 62• Standard cooling operating range from 40°F up to 115°F

(4°C up to 46°C). Field installable accessory extends theminimum down to –20°F (–29°C)

• Field convertible from vertical to horizontal airflow forslab mounting

• Two-inch disposable return air filters• Thru-the-bottom power and gas entry capability• Single point gas and electric connections• 24-volt control circuit protected with resettable circuit

breaker and 75-VA transformer• Belt drive, constant torque, permanently lubricated

evaporator-fan motor• Totally enclosed condenser motors with permanently

lubricated bearings• Low-pressure and high-pressure switches• Full perimeter base rail with built-in rigging adapters

and fork truck slots• Central Terminal Board for component and unit wiring

connectionsStandard Base Unit (Non-United States Models)• All features listed above• IEERs:

—up to 11.8 with standard motor—up to 12.8 with 2 speed/VFD indoor fan motor

• Two-stage/one-circuit cooling capacity control (sizes 08to 12)

Cabinet (All)• Access panels with easy grip handles and NO-STRIP

screw collars• Pre-painted exterior panels and primer-coated interior

panels tested to 500 hours salt spray protection• Fully insulated cabinet• Tool-less filter access door

Refrigerant System (All)• Accutrol† and/or TXV refrigerant metering system• Liquid line filter drier• Scroll compressors with internal line-break overload

protection• Copper tube, aluminum fin evaporator coils• Top cover removable gauge line plugs for reading

refrigerant pressure with unit panels in place• Round Tube/Plate Fin (RTPF) condenser coils on all

model sizes or Novation® all aluminum condenser coilsavailable on sizes 08-14 with two-stage/two-circuit

Gas Heat (All)• IGC solid-state gas heat exchanger control for on-board

diagnostics, anti-cycle protection, LED error code des-ignation, burner control logic and energy saving indoorfan motor delay

• Gas efficiencies up to 82%• Designed in accordance with ANSI Z21.47 (design and

test standard for gas furnaces) and ANSI Z233.1(National Fuel Gas code relating to appliance installa-tion requirements)

• Induced draft combustion• Redundant gas valve, with up to 2 stages of heating• Flame roll-out safety protector• Solid-state electronic direct spark ignition systemStandard Limited Parts Warranty• 15-year limited on all gas heat exchanger parts -

Stainless Steel• 10-year limited on all gas heat exchanger parts -

Aluminized• 5-year limited on all compressor parts• 5-year parts on Factory Installed Ultra Low Leak

Economizer• 3-year limited on all Novation condenser coil parts• 1-year limited on all Round Tube/Plate Fin (RTPF con-

denser coil parts• 1-year limited on all parts

* IECC is a registered trademark of International Code Council Inc.† Accutrol is a trademark of Accutrol LLC.

3

PERFORMANCE DATAUnit Operating Weight __________________________ lb

COOLING

Gross Total Capacity __________________________ Btuh

at Condenser Air Temperature __________________ °F

Gross Sensible Capacity _______________________ Btuh

Compressor Power Input _______________________ kW

Indoor Entering: db __________ °F / wb __________ °F

Airflow _____ CFM External Static Pressure _____ in. wg

Indoor Fan Motor Size __________________________ HP

Exhaust Fan Motor Size ________________________ HP

Curb Weight __________________________________ lb

HEATING (GAS)

Heating Capacity:

Stage 1 ____________________________________ Btuh

Stage 2 ____________________________________ Btuh

Heating Capacity Total _______________________ Btuh

Stage 1 ____________________________________ kW

Stage 2 ____________________________________ kW

Heating Capacity Total _______________________ kW

ELECTRICAL DATA

Power Supply to Unit ____________________________________

Volts _________________________________________________

Phase _________________________________________________ Hz

Maximum Circuit Amps __________________________________

Maximum Overcurrent Protection __________________________

SUBMITTAL DATA

Job Name _____________________________________________

Architect ______________________________________________

Engineer _____________________________________________

Contractor _____________________________________________

Unit Designation ________________________________________

Use of the AHRI CertifiedTM Mark indicates amanufacturer’s participation in the program. For verification of certification for individual products, go to www.ahridirectory.org.

4

FACTORY-INSTALLED OPTIONS

Economizer with DRY BULB Sensing and Baro-metric ReliefLow Leak Air Dampers —

Models with W7212 controller provide standardnon-diagnostic control (EconoMi$er® IV system).Models with W7220 controller meet CaliforniaTitle 24-2016 (Section 120.2) for FaultDetection and Diagnostic (FDD) requirements(EconoMi$er X system).Models with RTU Open controller meet Califor-nia Title 24-2016 (Section 120.2) FaultDetection and Diagnostic (FDD) requirements(EconoMi$er 2 system).

Economizer with ENTHALPY Sensing and Baro-metric ReliefLow Leak Air Dampers —

Models with W7212 controller provide standardnon-diagnostic control (EconoMi$er® IV system).Models with W7220 controller meet CaliforniaTitle 24-2016 (Section 120.2) Fault Detection andDiagnostic (FDD) requirements (EconoMi$er Xsystem).Models with RTU Open controller meet Califor-nia Title 24-2016 (Section 120.2) FaultDetection and Diagnostic (FDD) requirements(EconoMi$er 2 system).

Economizer with DRY BULB Sensing and Baro-metric ReliefULTRA LOW LEAK Air Dampers —

Models with W7220 controller meet CaliforniaEnergy Commission Title 24-2016 perspectivesection 140.4 (damper leakage, etc.), and man-datory section 120.2.i for Fault Detection andDiagnostic controls. Economizers meetASHRAE 90.1-2016 damper leakage require-ments as stated in section 6.5.1.1.4 and Table6.4.3.4.3, and meet 2016 Fault Detection andDiagnosis requirements in section 6.4.3.12. Foroutside air, return, and relief air damper leakagerequirements economizers meet IECC 2012section C402.4.5.2 and, IECC 2015 sectionsC403.2.4.3 and C403.3.3.5 and IECC 2015 sec-tion C403.2.4.7 for Fault Detection and Diag-nostic requirements. NOTE: IECC 2015 section C403.2.4.7.1 re-quires differential return air sensor, which mustbe ordered separately.Outside air, return air, and relief air (volume)dampers are AMCA rated — plus 5 year limitedparts warranty (EconoMi$er X system).Models with RTU Open meet California EnergyCommission Title 24-2016 perspective section140.4 (damper leakage, etc.) and mandatorysection 120.2.i for Fault Detection and Diag-nostic requirements. Economizers meetASHRAE 90.1-2016 damper leakage require-ments as stated in section 6.5.1.1.4 and Table

6.4.3.4.3, and meet 2016 Fault Detection andDiagnosis requirements in section 6.4.3.12.Economizers meet IECC 2012 sectionC402.4.5.2 and, IECC 2015 sectionsC403.2.4.3 and C403.3.3.5 for outside air, re-turn air, and relief air damper leakage require-ments and IECC 2015 section C403.2.4.7 forFault Detection and Diagnostic requirements. NOTE: IECC 2015 section C403.2.4.7.1 re-quires differential return air sensor, which mustbe ordered separately.Outside air, return air, and relief air (volume)dampers are AMCA rated — plus 5 year limitedparts warranty (EconoMi$er 2 system).

Economizer with ENTHALPY Sensing and Baro-metric ReliefULTRA LOW LEAK Air Dampers —

Models with W7220 controller meet CaliforniaEnergy Commission Title 24-2016 perspectivesection 140.4 (damper leakage, etc.), and man-datory section 120.2.i for Fault Detection andDiagnostic controls. Economizers meetASHRAE 90.1-2016 damper leakage require-ments as stated in section 6.5.1.1.4 and Table6.4.3.4.3, and meet 2016 Fault Detection andDiagnosis requirements in section 6.4.3.12. Foroutside air, return, and relief air damper leakagerequirements economizers meet IECC 2012section C402.4.5.2 and, IECC 2015 sectionsC403.2.4.3 and C403.3.3.5 and IECC 2015 sec-tion C403.2.4.7 for Fault Detection and Diag-nostic requirements. NOTE: IECC 2015 section C403.2.4.7.1 re-quires differential return air sensor, which mustbe ordered separately.Outside air, return air, and relief air (volume)dampers are AMCA rated — plus 5 year limitedparts warranty (EconoMi$er X system).Models with RTU Open meet California EnergyCommission Title 24-2016 perspective section140.4 (damper leakage, etc.) and mandatorysection 120.2.i for Fault Detection and Diag-nostic requirements. Economizers meetASHRAE 90.1-2016 damper leakage require-ments as stated in section 6.5.1.1.4 and Table6.4.3.4.3, and meet 2016 Fault Detection andDiagnosis requirements in section 6.4.3.12.Economizers meet IECC 2012 sectionC402.4.5.2 and, IECC 2015 sectionsC403.2.4.3 and C403.3.3.5 for outside air, re-turn air, and relief air damper leakage require-ments and IECC 2015 section C403.2.4.7 forFault Detection and Diagnostic requirements. NOTE: IECC 2015 section C403.2.4.7.1 re-quires differential return air sensor, which mustbe ordered separately.Outside air, return air, and relief air (volume)dampers are AMCA rated — plus 5 year limitedparts warranty (EconoMi$er 2 system).

5

FACTORY-INSTALLED OPTIONS (CONT)

Standard Base Unit (United States Models) RTU Open multi-protocol controller communicates toBACnet*, Modbus†, LonWorks**, and Johnson N2protocols.

Through the base connectors for gas and electricconduit/piping

Stainless steel gas heat exchanger (includes tubes,vestibule plate and collector box)

Perfect Humidity™ adaptive dehumidification system(RTPF condenser coil units only)

Two-position motorized outdoor air damper Non-fused disconnect Powered 115-volt convenience outlet Non-powered 115-volt convenience outlet High static evaporator fan motor Return Air smoke detector Supply Air smoke detector

CO2 sensor Condenser hail guard-louvered style Special coating protection for evaporator andcondenser coils

Hinged access doors Condensate overflow switch Stainless steel gas heat exchanger

Standard Base Unit (Non-United States Models) 2-speed indoor fan system

Optional Warranties Complete unit parts only, up to 5 years Complete unit parts and labor, up to 5 years

Many other optional warranties are available. See theCommercial Start-Up and Optional ExtendedWarranty Price pages for further information.

* BACnet is a registered trademark of ASHRAE (American Society of Heating, Refrigerating and Air-Conditioning Engineers).† Modbus is a registered trademark of Schneider Electric.** LonWorks is a registered trademark of Echelon Corporation.

6

FIELD-INSTALLED ACCESSORIES

Economizer with DRY BULB Sensing and Baro-metric ReliefStandard Leak Air Dampers —

Models with W7212 controller provide standardnon-diagnostic control (EconoMi$er® IV system).Models with W7220 controller meet CaliforniaTitle 24-2016 Section 120.2.i for FaultDetection and Diagnostic (FDD) requirements.(EconoMi$er X system).Models with RTU Open controller meet Califor-nia Title 24-2016 Section 120.2.i FaultDetection and Diagnostic (FDD) requirements.(EconoMi$er 2 system).

Economizer with ENTHALPY Sensing and Baro-metric ReliefStandard Leak Air Dampers —

Models with W7212 controller provide standardnon-diagnostic control (EconoMi$er IV system).Models with W7220 controller meet CaliforniaTitle 24-2016 Section 120.2.i Fault Detection andDiagnostic (FDD) requirements (EconoMi$er Xsystem).Models with RTU Open controller meet Califor-nia Title 24-2016 Section 120.2.i FaultDetection and Diagnostic (FDD) requirements(EconoMi$er 2 system).

Economizer with DRY BULB Sensing and Baro-metric ReliefULTRA LOW LEAK Air Dampers —

Models with W7220 controller meet CaliforniaEnergy Commission Title 24-2016 perspectivesection 140.4 (damper leakage, etc.), and man-datory section 120.2.i for Fault Detection andDiagnostic controls. Economizers meetASHRAE 90.1-2016 damper leakage require-ments as stated in section 6.5.1.1.4 and Table6.4.3.4.3, and meet 2016 Fault Detection andDiagnosis requirements in section 6.4.3.12. Foroutside air, return, and relief air damper leakagerequirements economizers meet IECC 2012section C402.4.5.2 and, IECC 2015 sectionsC403.2.4.3 and C403.3.3.5 and IECC 2015 sec-tion C403.2.4.7 for Fault Detection and Diag-nostic requirements.NOTE: IECC 2015 section C403.2.4.7.1 re-quires differential return air sensor, which mustbe ordered separately.Outside air, return air, and relief air (volume)dampers are AMCA rated (EconoMi$er Xsystem).

Models with RTU Open meet California EnergyCommission Title 24-2016 perspective section140.4 (damper leakage, etc.) and mandatorysection 120.2.i for Fault Detection and Diag-nostic requirements. Economizers meetASHRAE 90.1-2016 damper leakage require-ments as stated in section 6.5.1.1.4 and Table6.4.3.4.3, and meet 2016 Fault Detection andDiagnosis requirements in section 6.4.3.12.Economizers meet IECC 2012 sectionC402.4.5.2 and, IECC 2015 sectionsC403.2.4.3 and C403.3.3.5 for outside air, re-turn air, and relief air damper leakage require-ments and IECC 2015 section C403.2.4.7 forFault Detection and Diagnostic requirements. NOTE: IECC 2015 section C403.2.4.7.1 re-quires differential return air sensor, which mustbe ordered separately.Outside air, return air, and relief air (volume)dampers are AMCA rated (EconoMi$er 2system).

Economizer with ENTHALPY Sensing and Baro-metric ReliefULTRA LOW LEAK Air Dampers —

Models with W7220 controller meet CaliforniaEnergy Commission Title 24-2016 perspectivesection 140.4 (damper leakage, etc.), and man-datory section 120.2.i for Fault Detection andDiagnostic controls. Economizers meetASHRAE 90.1-2016 damper leakage require-ments as stated in section 6.5.1.1.4 and Table6.4.3.4.3, and meet 2016 Fault Detection andDiagnosis requirements in section 6.4.3.12. Foroutside air, return, and relief air damper leakagerequirements economizers meet IECC 2012section C402.4.5.2 and, IECC 2015 sectionsC403.2.4.3 and C403.3.3.5 and IECC 2015 sec-tion C403.2.4.7 for Fault Detection and Diag-nostic requirements.NOTE: IECC 2015 section C403.2.4.7.1 re-quires differential return air sensor, which mustbe ordered separately.Outside air, return air, and relief air (volume)dampers are AMCA rated (EconoMi$er Xsystem).Models with RTU Open meet California EnergyCommission Title 24-2016 perspective section140.4 (damper leakage, etc.) and mandatorysection 120.2.i for Fault Detection and Diag-nostic requirements. Economizers meetASHRAE 90.1-2016 damper leakage require-ments as stated in section 6.5.1.1.4 and Table6.4.3.4.3, and meet 2016 Fault Detection andDiagnosis requirements in section 6.4.3.12.Economizers meet IECC 2012 sectionC402.4.5.2 and, IECC 2015 sectionsC403.2.4.3 and C403.3.3.5 for outside air, re-turn air, and relief air damper leakage require-ments and IECC 2015 section C403.2.4.7 forFault Detection and Diagnostic requirements. NOTE: IECC 2015 section C403.2.4.7.1 re-quires differential return air sensor, which mustbe ordered separately.Outside air, return air, and relief air (volume)dampers are AMCA rated (EconoMi$er 2system).

7

FIELD-INSTALLED ACCESSORIES (CONT)

Display Kit for Variable Frequency Drive (VFD), 2-speed indoor fan motor system. Allows additional set up and diagnostics of the unit VFD controller. Can be unit mounted or used with any other compatible VFD model as a reusable device.

Prop power exhaust Two-position motorized outdoor air damper Manual outside air damper 25% Manual outside air damper 50% Roof Curb — 14 inch (356 mm) tall Roof Curb — 24 inch (610 mm) tall Thru-the-bottom connections (electrical only) Thru-the-bottom connections (electrical and gas) Condenser hail guard (louvered style) Flue shield Flue discharge deflector Liquid propane (LP) conversion kit High altitude conversion kit Phase monitor (loss of phase/phase reversal) Winter start kit, down to 25°F (–4°C)

Low ambient head pressure controller, down to 0°F (–18°C)

Low ambient head pressure controller, down to –20°F (–29°C)

Time Guard II compressor anti-cycle protection Thermostats and Sensors Supply duct kit (size 16 units only) Disconnect switch bracket (size 16 units only) Condensate overflow switch Non-powered 115-volt (20 amp) convenience outlet Side access hinged filter door kit Horn/strobe annunciator

Economizer Sensors Single Dry bulb control Differential Dry bulb control Single enthalpy control Differential enthalpy control CO2 — wall mounted CO2 — duct mounted CO2 — unit mounted

8

CE

RT

IFIE

D D

IME

NS

ION

PR

INT

Fig

. 1 —

580

J*08

-12

Dim

ensi

on

al D

raw

ing

9

CE

RT

IFIE

D D

IME

NS

ION

PR

INT

Fig

. 2 —

580

J*08

-12

Co

rner

Wei

gh

ts

10

CE

RTI

FIE

D D

IME

NS

ION

PR

INT

Fig

. 3 —

580

J*14

Dim

ensi

on

al D

raw

ing

11

CE

RTI

FIE

D D

IME

NS

ION

PR

INT

Fig

. 4 —

580

J*14

Co

rner

Wei

gh

ts

12

CE

RTI

FIE

D D

IME

NS

ION

PR

INT

Fig

. 5 —

580

J*16

Dim

ensi

on

al D

raw

ing

13

CE

RTI

FIE

D D

IME

NS

ION

PR

INT

Fig

. 6 —

580

J*16

Co

rner

Wei

gh

ts

14

CE

RTI

FIE

D R

OO

F C

UR

B D

ETA

ILS

Fig

. 7 —

580

J*08

-14

Ro

of

Cu

rb D

etai

ls

7/16

"[1

1]

4 9/

16"

[115

.5]

1/4"

[7.0

]

"A"

1 3/

4"[4

4.5]

1 3/

4"[4

4.4]

20-3

/4"

[513

]IN

SID

E

"A"

81 3

/4"

[207

6.3]

53 1

/2"

[135

8.9]

1 3/

4"[4

4.5]

40 3

/16"

[102

0.8]

2 1/

4"[5

7.2]

26"

[660

.4]

4 3/

16"

[106

.0]

6 3/

64"

[153

.5]

32 9

/16"

[827

.1]

23 1

/16"

[585

.8]

31 1

7/32

"[8

00.9

]1

3/4"

[44.

5]

15 1

3/16

"[4

01.6

]

11.4

2"[2

90.0

]

1 3/

4"[4

4.4]

3"[7

6.2]

2-3/

8"[6

1]

14 3

/4"

[374

.7]

6' 6

-1/4

"[1

987.

5]

1-3

/4"

TYP

[44.

5]

4' 2

"[1

270.

0]

15 1

5/32

[392

.9]

1.00

"[2

5.4]

CR

BTM

PWR

002A

013/

4" [1

9] N

PT1

1/4"

[31.

7] N

PTC

RR

FCU

RB0

04A0

1

CO

NN

ECTO

R P

KG. A

CC

.G

AS C

ON

NEC

TIO

N T

YPE

GAS

FIT

TIN

GPO

WER

WIR

ING

FI

TTIN

GC

ON

TRO

L W

IRIN

G

FITT

ING

ACC

ESSO

RY

CO

NVE

NIE

NC

E O

UTL

ET W

IRIN

G C

ON

NEC

TOR

THR

U T

HE

CU

RB

1/2"

[12.

7] N

PT1/

2" [1

2.7]

NPT

CR

BTM

PWR

004A

01TH

RU

TH

E BO

TTO

M

RO

OF

CU

RB

ACC

ESSO

RY

#A

CR

RFC

UR

B003

A01

14"

[356

]

24"

[610

]

ECN

NO

.AP

P'D

CH

K'D

BYD

ATE

REV

ISIO

N R

ECO

RD

REV

1067

898

--

MM

C4/

22/1

36'

61/

4" W

AS 6

' 7 1

/6",

4'2'

WAS

4' 2

13/

16";

18 G

A W

AS 1

6 G

A.; 1

5 13

/16"

WAS

15

15/1

6"; N

AIL

FIEL

D S

UPP

LIED

WAS

WIT

H C

UR

BC

DR

AWIN

G R

ELEA

SE L

EVEL

:PR

OD

UC

TIO

NTH

IRD

AN

GLE

PRO

JEC

TIO

N

UN

LESS

OTH

ERW

ISE

SPEC

IFIE

DD

IMEN

SIO

NS

ARE

IN IN

CH

ESTO

LER

ANC

ES O

N:

THIS

DO

CU

MEN

T AN

D T

HE

INFO

RM

ATIO

N C

ON

TAIN

ED T

HER

EIN

IS P

RO

PRIE

TAR

Y TO

CAR

RIE

R C

OR

POR

ATIO

N A

ND

SH

ALL

NO

TBE

USE

D O

R D

ISC

LOSE

D T

O O

THER

S, IN

WH

OLE

OR

IN P

ART,

WIT

HO

UT

THE

WR

ITTE

N A

UTH

OR

IZAT

ION

OF

CAR

RIE

R C

OR

POR

ATIO

N.

1 D

EC2

DEC

3 D

ECAN

GM

ATER

IAL

--

--

- - -

AUTH

OR

IZAT

ION

NU

MBE

RTI

TLE

1029

120

CU

RB

ASY,

RO

OF

ENG

INEE

RIN

GM

ANU

FAC

TUR

ING

ENG

INEE

RIN

G R

EQU

IREM

ENTS

--

--

SIZE

DR

AWIN

G N

UM

BER

REV

T-00

5, Y

-002

DR

AFTE

RC

HEC

KER

D50

HJ4

0501

2C

WEI

GH

T:-

MM

C12

/16/

09-

-SH

EET

5 O

F 5

SUR

FAC

E FI

NIS

HM

FG/P

UR

CH

MO

DEL

(IN

TER

NAL

USE

ON

LY)

NEX

T D

RAW

ING

SCAL

ED

ISTR

IBU

TIO

N

-PU

RC

H-

N/A

-

NO

TES:

1. R

OO

FCU

RB

ACC

ESSO

RY

IS S

HIP

PED

DIS

ASSE

MBL

ED.

2. IN

SULA

TED

PAN

ELS:

25.

4 [1

"] TH

K. P

OLY

UR

ETH

ANE

FOAM

, 44.

5 [1

-3/4

] # D

ENSI

TY.

3. D

IMEN

SIO

NS

IN [

] AR

E IN

MIL

LIM

ETER

S.4.

RO

OFC

UR

B: 1

8 G

AGE

STEE

L.5.

ATT

ACH

DU

CTW

OR

K TO

CU

RB.

(FLA

NG

ES O

F D

UC

T R

EST

ON

CU

RB)

.6.

SER

VIC

E C

LEAR

ANC

E 4

FEET

ON

EAC

H S

IDE.

7.

DIR

ECTI

ON

OF

AIR

FLO

W.

8. C

ON

NEC

TOR

PAC

KAG

E C

RBT

MPW

R00

2A01

IS F

OR

TH

RU

-TH

E-C

UR

B G

AS T

YPE

PA

CKA

GE

CR

BTM

PWR

004A

01 IS

FO

R T

HR

U-T

HE-

BOTT

OM

TYP

E G

AS C

ON

NEC

TIO

NS.

TYPI

CAL

(4) S

IDES

SUPP

LY A

IRR

ETU

RN

AIR

RO

OFI

NG

MAT

ERIA

L(F

IELD

SU

PPLI

ED)

CAN

T ST

RIP

(FIE

LD S

UPP

LIED

)

RO

OFI

NG

FEL

T(F

IELD

SU

PPLI

ED)

CO

UN

TER

FLA

SHIN

G(F

IELD

SU

PPLI

ED)

UN

ITG

ASKE

T(S

UPP

LIED

WIT

H C

UR

B)

RIG

ID IN

SULA

TIO

N(F

IELD

SU

PPLI

ED)

DU

CT

(FIE

LD S

UPP

LIED

)

NAI

L (F

IELD

SU

PPLI

ED)

CER

TIFI

ED D

RAW

ING

VIEW

"B"

CO

RN

ER D

ETAI

L

SEC

TIO

N T

HR

U S

IDE

SE

E V

IEW

"B

"

GAS

SER

VIC

E PL

ATE

THR

U T

HE

CU

RB

DR

ILL

HO

LE

2" [5

0.8]

@

ASSE

MBL

Y (IF

R

EQU

IRED

) (S

EE N

OTE

#8)

SEE

NO

TE #

2

12-1

/2" [

317.

5] W

IDE

INSU

LATE

D D

ECK

PAN

ELS

9-15

/16"

[252

.4] W

IDE

INSU

LATE

D D

ECK

PAN

EL

SUPP

LY A

IRR

ETU

RN

AIR

SUPP

LY A

IRO

PEN

ING

RET

UR

N A

IRO

PEN

ING

15

CE

RTI

FIE

D R

OO

F C

UR

B D

ETA

ILS

Fig

. 8 —

580

J*16

Ro

of

Cu

rb D

etai

ls

Copyright 2018 Bryant Heating & Cooling Systems Edition Date: 11-19 Printed in U.S.A Catalog No: SUB580J–8-16-03 Rev/A

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations. Pg 16 Replaces: SUB580J–8-16-02