50 Ken Garff - Amazon S3 · mdp main distribution panel mg motor generator mh manhole min minimum...
21
324 S. State St., Suite 400 Salt Lake City, UT 84111 800-678-7077 801-328-5151 fax: 801-328-5155 www.spectrum-engineers.com Ken Garff Automotive Group COPYRIGHTED DOCUMENT THIS DRAWING AND THE BIM/CAD FILE FROM WHICH IT HAS BEEN GENERATED ARE PROVIDED AS AN INSTRUMENT OF SERVICE FOR THIS PROJECT. THESE DOCUMENTS ARE THE SOLE PROPERTY GOREE ARCHITECTS. ANY USE OF THESE DOCUMENTS, DATA AND DESIGNS FOR PURPOSES OTHER THAN THOSE ASSOCIATED WITH THIS PROJECT WITHOUT THE EXPRESSED, WRITTEN PERMISSION OF FRED GOREE ARCHITECTS IS PROHIBITED. Revision History: Project No: 1503 Date: Mark: t. 713-660-6102 4710 Bellaire Blvd. #105 Bellaire, Texas 77401 G O R E E A R C H I T E C T S 50 1963-2013 YEARS 11/03/15 DD SET DATE: 11/11/2015 SHEET INDEX, ABBREVIATIONS, AND GENERAL NOTES E-001 DOWNTOWN SALT LAKE Jaguar - Land Rover 150 E 500 S, SALT LAKE CITY, UT 84111 A NEW AUTOMOTIVE FACILITY DESIGN FOR ELECTRICAL SHEET INDEX E-001 SHEET INDEX, ABBREVIATIONS, AND GENERAL NOTES E-100 POWER PLAN E-101 MEZZANINE POWER PLAN E-102 ROOF POWER PLAN E-103 LIGHTING PLAN E-104 MEZZANINE LIGHITNG PLAN E-105 FIRE ALARM PLAN E-106 MEZZANINE FIRE ALARM PLAN E-107 TELECOM PLAN E-108 MEZZANINE TELECOM PLAN E-401 ENLARGED TELECOM PLANS E-601 ONE-LINE DIAGRAM E-602 FIRE ALARM RISER E-603 EQUIPMENT SCHEDULE E-604 INTERIOR LIGHTING FIXTURE SCHEDULE E-605 PANEL SCHEDULES E-606 PANEL SCHEDULES E-607 TELECOM SCHEDULES AND NOTES E-608 TELECOM RISER DIAGRAMS E-701 TYPICAL MOUNTING HEIGHT DETAILS GENERAL ELECTRICAL NOTES 3. EXPOSED STRUCTURE AREAS (EXCLUDING MECHANICAL, ELECTRICAL, AND COMMUNICATION SPACES): INSTALL RACEWAYS BETWEEN DECK AND STRUCTURE WHEREVER POSSIBLE IN EXPOSED STRUCTURE CEILING AREAS. ROUTE RACEWAYS IN CONCEALED AREAS WHEREVER POSSIBLE. REFER ALL CONDITIONS WHERE RACEWAYS MUST BE INSTALLED WHICH CANNOT COMPLY WITH THESE REQUIREMENTS TO THE ARCHITECT. 4. SUBMITTALS: PROVIDE ORIGINAL ELECTRONIC PDF FORMAT, BOUND, BOOKMARKED (EACH SECTION AND PRODUCT), AND HIGHLIGHTED. JOB NAME AND SUBCONTRACTOR SHALL BE ON THE FRONT COVER. PREPARE INDEX OF EQUIPMENT SUBMITTED IN EACH TAB. 5. REFLECTED CEILING PLANS: COORDINATE THE LOCATION OF LIGHT FIXTURES WITH THE ARCHITECTURAL REFLECTED CEILING PLANS. REFER ALL DISCREPANCIES TO THE ARCHITECT AND ENGINEER. 6. ALL WORK SHALL BE DONE ACCORDING TO THE CURRENT NATIONAL ELECTRIC CODE (NEC), IBC, NFPA, AND IFC. COMPLIANCE AND FINAL APPROVAL IS SUBJECT TO THE ON SITE FIELD INSPECTION OF THE AHJ. 1. CLARIFICATION METHODS: AT THE TIME OF BIDDING, BIDDERS SHALL FAMILIARIZE THEMSELVES WITH THE DRAWINGS AND SPECIFICATIONS. ANY QUESTIONS, MISUNDERSTANDINGS, CONFLICTS, DELETIONS, DISCONTINUED PRODUCTS, CATALOG NUMBER DISCREPANCIES, DISCREPANCIES BETWEEN THE EQUIPMENT SUPPLIED AND THE INTENT OR FUNCTION OF THE EQUIPMENT, ETC, SHALL BE SUBMITTED TO THE ARCHITECT/ENGINEER IN WRITING FOR CLARIFICATION PRIOR TO ISSUANCE OF THE FINAL ADDENDUM AND BIDDING OF THE PROJECT. WHERE DISCREPANCIES OR MULTIPLE INTERPRETATIONS OCCUR, THE MOST STRINGENT (WHICH IS GENERALLY RECOGNIZED AS THE MOST COSTLY) THAT MEETS THE INTENT OF THE DOCUMENTS SHALL BE ENFORCED. 2. OWNER FURNISHED ITEMS: THE OWNER WILL FURNISH MATERIAL AND EQUIPMENT AS INDICATED IN THE CONTRACT DOCUMENTS TO BE INCORPORATED INTO THE WORK. THESE ITEMS ARE ASSIGNED TO THE INSTALLER AND COSTS FOR RECEIVING, HANDLING, STORAGE, IF REQUIRED, AND INSTALLATION ARE INCLUDED IN THE CONTRACT SUM. A. THE INSTALLER'S RESPONSIBILITIES ARE THE SAME AS IF THE INSTALLER FURNISHED THE MATERIALS OR EQUIPMENT. B. THE OWNER WILL ARRANGE AND PAY FOR DELIVERY OF OWNER FURNISHED ITEMS FREIGHT ON BOARD JOB SITE AND THE INSTALLER WILL INSPECT DELIVERIES FOR DAMAGE. IF OWNER FURNISHED ITEMS ARE DAMAGED, DEFECTIVE OR MISSING, DOCUMENT DAMAGED ITEMS WITH THE TRANSPORT COMPANY AND THE OWNER WILL ARRANGE FOR REPLACEMENT. THE OWNER WILL ALSO ARRANGE FOR MANUFACTURER'S FIELD SERVICES, AND THE DELIVERY OF MANUFACTURER'S WARRANTIES AND BONDS TO THE INSTALLER. C. THE INSTALLER IS RESPONSIBLE FOR DESIGNATING THE DELIVERY DATES OF OWNER FURNISHED ITEMS AND FOR RECEIVING, UNLOADING AND HANDLING OWNER FURNISHED ITEMS AT THE SITE.THE INSTALLER IS RESPONSIBLE FOR PROTECTING OWNER FURNISHED ITEMS FROM DAMAGE, INCLUDING DAMAGE FROM EXPOSURE TO THE ELEMENTS, AND TO REPAIR OR REPLACE ITEMS DAMAGED AS A RESULT OF HIS OPERATIONS. DEFINITIONS NOTE: ALL DEFINITIONS MAY NOT BE USED. INDICATED: THE TERM "INDICATED" REFERS TO GRAPHIC REPRESENTATIONS, NOTES, OR SCHEDULES ON THE DRAWINGS, OTHER PARAGRAPHS OR SCHEDULES IN THE SPECIFICATIONS, AND SIMILAR REQUIREMENTS IN THE CONTRACT DOCUMENTS. WHERE TERMS SUCH AS "SHOWN", "NOTED", "SCHEDULED", AND "SPECIFIED" ARE USED, IT IS TO HELP THE READER LOCATE THE REFERENCE, NO LIMITATION ON LOCATION IS INTENDED. DIRECTED: TERMS SUCH AS "DIRECTED", "REQUESTED", AUTHORIZED", "SELECTED", "APPROVED", "REQUIRED", AND "PERMITTED" MEAN "DIRECTED BY THE ENGINEER", "REQUESTED BY THE ENGINEER", AND SIMILAR PHRASES. APPROVED: THE TERM "APPROVED", WHERE USED IN CONJUNCTION WITH THE ENGINEER'S ACTION ON THE CONTRACTOR'S SUBMITTALS, APPLICATIONS, AND REQUESTS, IS LIMITED TO THE ENGINEER'S DUTIES AND RESPONSIBILITIES AS STATED IN GENERAL AND SUPPLEMENTARY CONDITIONS. FURNISH: THE TERM "FURNISH" IS USED TO MEAN "SUPPLY AND DELIVER TO THE PROJECT SITE, READY FOR UNLOADING, UNPACKING, ASSEMBLY, INSTALLATION, AND SIMILAR OPERATIONS." INSTALL: THE TERM "INSTALL" IS USED TO DESCRIBE OPERATIONS AT PROJECT SITE INCLUDING THE ACTUAL "UNLOADING, UNPACKING, ASSEMBLY, ERECTION, PLACING, ANCHORING, APPLYING, WORKING TO DIMENSION, FINISHING, CURING, PROTECTING, CLEANING, AND SIMILAR OPERATIONS." PROVIDE: THE TERM "PROVIDE" MEANS "TO FURNISH AND INSTALL, COMPLETE AND READY FOR THE INTENDED USE." INSTALLER: AN "INSTALLER" IS THE CONTRACTOR OR AN ENTITY ENGAGED BY THE CONTRACTOR, EITHER AS AN EMPLOYEE, SUBCONTRACTOR, OR SUB- SUBCONTRACTOR, FOR PERFORMANCE OF A PARTICULAR CONSTRUCTION ACTIVITY, INCLUDING INSTALLATION, ERECTION, APPLICATION, AND SIMILAR OPERATIONS. INSTALLERS ARE REQUIRED TO BE EXPERIENCED IN THE OPERATIONS THEY ARE ENGAGED TO PERFORM. TECHNOLOGY SYSTEMS: THE TERM "TECHNOLOGY SYSTEMS" IS USED TO DESCRIBE ALL LOW VOLTAGE SYSTEMS GENERALLY REFERRED TO AS "SPECIAL SYSTEMS". THESE SYSTEMS INCLUDE BUT ARE NOT NECESSARILY LIMITED TO ALL SYSTEMS WHICH UTILIZE VOLTAGES OF LESS THAN 71 VOLTS SUCH AS SOUND SYSTEMS, VIDEO SYSTEMS, TV SYSTEMS, SECURITY SYSTEMS, VOICE AND DATA CABLING SYSTEMS, ETC... ABBREVIATIONS NOTE: ALL ABBREVIATIONS MAY NOT BE USED. kVA KILOVOLT AMPERE kVAR KILOVOLT AMPERE REACTIVE kW KILOWATT kWh KILOWATT HOUR LED LIGHT EMITTING DIODE LFMC LIQUID TIGHT FLEXIBLE METAL CONDUIT LFNC LIQUID TIGHT FLEXIBLE NONMETALLIC CONDUIT LPS LOW PRESSURE SODIUM LRA LOCKED ROTOR AMPS LTG LIGHTING LV LOW VOLTAGE MATV MASTER ANTENNA TELEVISION SYSTEM MAX MAXIMUM MC METAL CLAD MCA MINIMUM CIRCUIT AMPS MCB MAIN CIRCUIT BREAKER MCC MOTOR CONTROL CENTER MCP MOTOR CIRCUIT PROTECTION MDP MAIN DISTRIBUTION PANEL MG MOTOR GENERATOR MH MANHOLE MIN MINIMUM MLO MAIN LUGS ONLY MOCP MAXIMUM OVERCURRENT PROTECTION NA NOT APPLICABLE NC NORMALLY CLOSED NEC NATIONAL ELECTRICAL CODE NEMA NATIOANL ELECTRICAL MANUFACTURERS ASSOCIATION NFC NATIONAL FIRE CODE NFPA NATIONAL FIRE PROTECTION ASSOCIATION NIC NOT IN CONTRACT NL NIGHT LIGHT NO NORMALLY OPEN NTS NOT TO SCALE OC ON CENTER OCP OVER CURRENT PROTECTION OF/CI OWNER FURNISHED/ CONTRACTOR INSTALLED OF/OI OWNER FURNISHED/ OWNER INSTALLED OFP OBTAIN FROM PLANS OH DR OVERHEAD (COILING) DOOR OL OVERLOAD PB PUSHBUTTON PF POWER FACTOR PH PHASE PNL PANEL PT POTENTIAL TRANSFORMER PTZ PAN/TILT/ZOOM QTY QUANTITY R REMOVE RCP REFLECTED CEILING PLAN RMC RIGID METAL CONDUIT RNC RIGID NONMETAL CONDUIT RPM REVOLUTIONS PER MINUTE RR REMOVE AND RELOCATE S/S START/STOP SCA SHORT CIRCUIT AMPS SCBA STANDARD COLOR AS SELECTED BY ARCHITECT SF SQUARE FOOT (FEET) SFBA STANDARD FINISH AS SELECTED BY ARCHITECT SPDT SINGLE POLE, DOUBLE THROW SPEC SPECIFICATION SPST SINGLE POLE, SINGLE THROW ST SINGLE THROW SWBD SWITCHBOARD SWGR SWITCHGEAR TL TWIST LOCK TP TELEPHONE POLE TP TWISTED PAIR TTB TELEPHONE TERMINAL BOARD TV TELEVISION TVSS TRANSIENT VOLTAGE SURGE SUPPRESSER TYP TYPICAL UF UNDERFLOOR UGND UNDERGROUND UPS UNINTERRUPTIBLE POWER SUPPLY V VOLTS VA VOLT AMPERE VFC/VFD VARIABLE FREQUENCY MOTOR CONTROLLER W/ WITH W/O WITHOUT WP WEATHERPROOF XFMR TRANSFORMER 1P SINGLE POLE 1PH SINGLE-PHASE 1WAY ONE-WAY 2/C TWO-CONDUCTOR 2WAY TWO-WAY 3/C THREE-CONDUCTOR 3WAY THREE-WAY 4OUT QUADRUPLE RECEPTACLE OUTLET 4PDT FOUR-POLE DOUBLE THROW 4PST FOUR-POLE SINGLE THROW 4W FOUR-WIRE 4WAY FOUR-WAY A ABOVE COUNTER AC ARMORED CABLE ADA AMERICANS WITH DISABILITIES ACT ADJ ADJACENT AFF ABOVE FINISHED FLOOR AFG ABOVE FINISHED GRADE AIC AMPERE INTERRUPTING CAPACITY ALUM ALUMINUM AMP AMPERE ANN ANNUNCIATOR AP ACCESS POINT (WIRELESS DATA) AR AS REQUIRED ASC AMPS SHORT CIRCUIT ATS AUTOMATIC TRANSFER SWITCH AV AUDIO VISUAL AWG AMERICAN WIRE GAGE BB XFMR BUCK-BOOST TRANSFORMER C CEILING MOUNTED CATV COMMUNITY ANTENNA TELEVISION CB CIRCUIT BREAKER CCBA CUSTOM COLOR AS SELECTED BY ARCHITECT CCTV CLOSED CIRCUIT TELEVISION CF/CI CONTRACTOR FURNISHED/ CONTRACTOR INSTALLED CF/OI CONTRACTOR FURNISHED/ OWNER INSTALLED CFBA CUSTOM FINISH AS SELECTED BY ARCHITECT CKT CIRCUIT CM CONSTRUCTION MANAGER CND CONDUIT CO CONVENIENCE OUTLET COR CONTRACTING OFFICER'S REPRESENTATIVE CP CONTROL PANEL CT CURRENT TRANSFORMER CTV CABLE TELEVISION CU COPPER dBA UNIT OF SOUND LEVEL DPDT DOUBLE POLE, DOUBLE THROW DS DISCONNECT SWITCH EA EACH EM EMERGENCY EMT ELECTRICAL METALLIC TUBING ENT ELECTRIC NONMETALLIC TUBING EPO EMERGENCY POWER OFF EQUIP EQUIPMENT EX EXISTING F FURNITURE MOUNTED FA FIRE ALARM FCP FIRE ALARM CONTROL PANEL FLA FULL LOAD AMPS FMC FLEXIBLE METAL CONDUIT FOB FREIGHT ON BOARD FVNR FULL VOLTAGE NON-REVERSING FVR FULL VOLTAGE REVERSING G GROUND GEN GENERATOR GFCI GROUND FAULT INTERRUPTER GFP GROUND FAULT PROTECTION HD HEAVY DUTY HID HIGH INTENSITY DISCHARGE HOA HAND-OFF-AUTOMATIC HP HORSE POWER HPF HIGH POWER FACTOR HPS HIGH PRESSURE SODIUM HV HIGH VOLTAGE HZ HERTZ I/O INPUT/ OUTPUT IG ISOLATED GROUND IMC INTERMEDIATE METAL CONDUIT IN/IS INSULATED/ ISOLATED IR INFRARED J-BOX JUNCTION BOX kV KILOVOLT SYMBOL DESCRIPTION SYMBOLS LEGEND SYMBOL DESCRIPTION SYMBOLS LEGEND SYMBOL DESCRIPTION SYMBOLS LEGEND SWITCH, TIMER OPERATED. T 50 SWITCH, DOUBLE POLE ("x" INDICATES FIXTURES CONTROLLED). X 2 41 SWITCH, THREE-WAY ("x" INDICATES FIXTURES CONTROLLED). X 3 42 SWITCH, FOUR-WAY ("x" INDICATES FIXTURES CONTROLLED). X 4 43 SWITCH, KEY OPERATED. K 45 FLUSH FLOOR BOX. "#" SHOWN ON DRAWINGS. REFER TO WIRING DEVICE SCHEDULE IN THE ELECTRICAL SPECIFICATIONS FOR CONFIGURATION AND DEVICES. FB# 36 POWER POLE. "#" SHOWN ON DRAWINGS. REFER TO WIRING DEVICE SCHEDULE IN THE ELECTRICAL SPECIFICATIONS FOR CONFIGURATION AND DEVICES. PP# 37 FLUSH FIRE RATED POKE THRU. "#" SHOWN ON DRAWINGS. REFER TO WIRING DEVICE SCHEDULE IN THE ELECTRICAL SPECIFICATIONS FOR CONFIGURATION AND DEVICES. PT# 38 SWITCH, DIMMER. D 39 SWITCH, SINGLE POLE ("x" INDICATES FIXTURES CONTROLLED). X 40 R RECEPTACLE, RANGE: NEMA 14-50R. 31 DROP CORD. SEE DETAIL. D 34 RECEPTACLE, QUADRAPLEX: NEMA 5-20R. 22 RECEPTACLE, QUADRAPLEX WITH GROUND FAULT CIRCUIT INTERRUPTER: NEMA 5-20R. 27 RECEPTACLE, SPECIAL PURPOSE. PROVIDE RECEPTACLE TO MATCH EQUIPMENT PLUG. 28 RECEPTACLE, DUPLEX, WEATHERPROOF: NEMA 5-20R. WP 11 RECEPTACLE, DUPLEX ON EMERGENCY POWER: NEMA 5-20R. 13 RECEPTACLE, DUPLEX WITH GROUND FAULT CIRCUIT INTERRUPTER: NEMA 5-20R. 16 RECEPTACLE, DUPLEX WITH GROUND FAULT CIRCUIT INTERRUPTER, WEATHERPROOF: NEMA 5-20R. WP 19 RECEPTACLE, DUPLEX WITH GROUND FAULT CIRCUIT INTERRUPTER, WET LABEL, "WEATHERPROOF IN USE": NEMA 5-20R. W 10 S RECEPTACLE, DUPLEX, SWITCHED: NEMA 5-20R. 08 DF RECEPTACLE, DUPLEX WITH GROUND FAULT CIRCUIT INTERRUPTER, DRINKING FOUNTAIN: CONCEAL WATER COOLER RECEPTACLE BEHIND WATER COOLER. SEE MECHANICAL/PLUMBING SHOP DRAWINGS FOR INSTALLATION REQUIREMENTS. 06 RECEPTACLE, DUPLEX, DEDICATED CIRCUIT: NEMA 5-20R. D 05 RECEPTACLE, DUPLEX, CEILING: NEMA 5-20R. C 04 RECEPTACLE, DUPLEX, ABOVE COUNTER: NEMA 5-20R. A 03 RECEPTACLE, DUPLEX: NEMA 5-20R. 02 WIRING DEVICES 00 SITE ELECTRICAL AND COMMUNICATIONS UTILITIES 00 UTILITY POLE. 03 TRANSFORMER. T 17 PANELBOARD WITH MAIN LUGS ONLY. BUS SIZE AND PHASE AS SHOWN (ONE-LINE DIAGRAM). 225/3 "1H" 23 PANELBOARD (ONE-LINE DIAGRAM). "1H" 22 PANELBOARD WITH MAIN CIRCUIT BREAKER. SIZE AND PHASE AS SHOWN (ONE-LINE DIAGRAM). 225/3 "1H" 24 PANELBOARD WITH MAIN AND SUB FEED CIRCUIT BREAKER (ONE-LINE DIAGRAM). 60/3 225/3 "1H" 25 TRANSFORMER (ONE-LINE DIAGRAM). 16 MOTOR. 12 CIRCUIT BREAKER, SOLID STATE WITH GROUND FAULT PROTECTION (ONE-LINE DIAGRAM). GFP 11 CIRCUIT BREAKER, SOLID STATE (ONE-LINE DIAGRAM). 10 CIRCUIT BREAKER, MOLDED CASE (ONE-LINE DIAGRAM). 07 CIRCUIT BREAKER, MOLDED CASE WITH SHUNT TRIP (ONE-LINE DIAGRAM). 08 DISCONNECT, FUSED (ONE-LINE DIAGRAM). 02 ELECTRICAL POWER AND DISTRIBUTION 00 EXIT SIGN: DOUBLE FACE; WALL MOUNTED 10 EXIT SIGN: SINGLE FACE; CEILING MOUNTED 07 EXIT SIGN: DOUBLE FACE; CEILING MOUNTED 09 EXIT SIGN: SINGLE FACE; WALL MOUNTED 08 LIGHTING (REFER TO FIXTURE SCHEDULE FOR SYMBOLS) 00 FIXTURE IDENTIFICATION: (W-3) INDICATES FIXTURE TYPE AS SCHEDULED. (W-3) 01 FIXTURE IDENTIFICATION, EMERGENCY WITH BATTERY PACK, CONNECTED TO GENERATOR AS INDICATED: (W-3) INDICATES FIXTURE TYPE AS SCHEDULED. (W-3) 02 EM EMERGENCY. 03 NL NIGHT LIGHT: DO NOT SWITCH. 04 EGRESS DIRECTION ARROW (EXIT SIGNS). 05 VACANCY SENSOR, DUAL TECHNOLOGY, WALL. 07 VACANCY SENSOR, DUAL TECHNOLOGY, OMNI-DIRECTIONAL, CEILING. 06 LIGHTING CONTROL 00 OCCUPANCY SENSOR, DUAL TECHNOLOGY, OMNI-DIRECTIONAL, CEILING. 01 OCCUPANCY SENSOR, DUAL TECHNOLOGY, WALL. 02 OCCUPANCY SENSOR, DUAL TECHNOLOGY, DIRECTIONAL. 03 PHOTOCELL. P 08 STRUCTURED CABLING 00 TELEPHONE, WALL MOUNTED ("X" INDICATES QUANTITY OF CABLES). X 01 TELEPHONE, WALL MOUNTED: WALL PHONE. W 03 OUTLET, DATA COMMUNICATION ("X" INDICATES QUANTITY OF CABLES). X 04 OUTLET, BUILDING STANDARD COMBINATION TELEPHONE/ DATA COMMUNICATION. 05 TELEPHONE TERMINAL BOARD, FIRE TREATED PLYWOOD PAINTED. 07 LAN RACK, FLOOR STANDING. 08 09 CONTRACT LIMIT LINE: DASHDOT, WIDE LINE. 17 PROPERTY LINE: DASHED, WIDE LINE. 16 HIDDEN FEATURES LINE: HIDDEN, THIN LINE 13 NEW LINE: MEDIUM LINE. 12 MATCH LINE INDICATOR: CENTER, EXTRA WIDE LINE. MATCH LINE SEE XX/X-XXX 11 BREAK, ROUND 10 BREAK, STRAIGHT: TO BREAK PARTS OF DRAWING 09 CU-1 EQUIPMENT INDICATOR. 07 REVISION INDICATOR. 1 06 KEYNOTE INDICATOR. 1 05 ROOM IDENTIFIER WITH ROOM NAME AND NUMBER. ROOM NAME 100 04 ELEVATION OR SECTION INDICATOR, EXTERIOR: A5 INDICATES ELEVATION OR SECTION NUMBER, E-201 INDICATES DRAWING SHEET WHERE ELEVATION OR SECTION IS SHOWN. A5 E-201 02 DETAIL INDICATOR: A5 INDICATES DETAIL NUMBER, E-501 INDICATES DRAWING SHEET WHERE DETAIL IS SHOWN. A5 E-501 01 REFERENCE AND LINE SYMBOLS 00 MECHANICAL EQUIPMENT CONNECTION. REFER TO EQUIPMENT SCHEDULE FOR REQUIREMENTS. 25 JUNCTION BOX, CEILING. C J 22 EARTH GROUND (ONE-LINE DIAGRAM). 21 CABLE TRAY ABOVE ACCESSIBLE CEILING. C C 19 PULL BOX. PB 18 JUNCTION BOX, SECURITY SYSTEM. PROVIDE CONDUIT AND ROUGH-IN PER SECURITY DRAWINGS. SE J 15 JUNCTION BOX, SYSTEMS FURNITURE COMMUNICATION CONNECTION. SC J 14 JUNCTION BOX. J 13 ADA ACCESS PUSH PLATE HC 12 CONDUCTOR & CONDUIT ("CC") SCHEDULE INDICATOR. REFER TO ONE-LINE DIAGRAM. 1 11 CONDUIT STUB. DIMENSION RECORD DRAWINGS AND MARK. 10 LOW VOLTAGE WIRING: DIVIDE, MEDIUM LINE. 09 WIRING AND/OR RACEWAY: THIN LINE. WHERE "X" = : CATV = CABLE TELEVISION NC = NURSE CALL CCTV = CLOSED CIRCUIT P = POWER TELEVISION RC = RIGID CONDUIT FA = FIRE ALARM S = SOUND FO = FIBER OPTICS T = TELEPHONE I = INTERCOM TV = TELEVISION OTHERS AS NOTED IN OTHER SCHEDULES. RACEWAYS AND WIRING SHALL BE SIZED AS SHOWN AND/OR SPECIFIED. X 08 BRANCH CIRCUIT HOME RUN TO PANELBOARD: NUMBER OF ARROWS INDICATES NUMBER OF CIRCUITS. LETTER AND NUMBER NOTATIONS IDENTIFY PANEL AND CIRCUIT NUMBERS. SMALL CROSS LINES INDICATE NUMBER OF CONDUCTORS OR CABLES. LARGER CROSS LINE INDICATES EQUIPMENT GROUND. WAVY CROSS LINE INDICATES INSULATED/ ISOLATED GROUND. FOR BRANCH WIRING, CROSS LINES INDICATE #12 CONDUCTORS, EXCEPT #10 CONDUCTORS SHALL BE INSTALLED IF DISTANCES EXCEED THOSE SPECIFIED IN THE ELECTRICAL SPECIFICATIONS. A-1,3,5 06 BRANCH CIRCUIT HOME RUN TO PANELBOARD: NUMBER OF ARROWS INDICATES NUMBER OF CIRCUITS. LETTER AND NUMBER NOTATIONS IDENTIFY PANEL AND CIRCUIT NUMBERS. NUMBER IN BOX REFERS TO THE CONDUCTOR AND CONDUIT SCHEDULE. FOR BRANCH WIRING USE #12 CONDUCTORS, EXCEPT #10 CONDUCTORS SHALL BE INSTALLED IF DISTANCES EXCEED THOSE SPECIFIED IN THE ELECTRICAL SPECIFICATIONS. A-1,3,5 1 05 BRANCH CIRCUIT HOME RUN TO PANELBOARD: NUMBER OF ARROWS INDICATES NUMBER OF CIRCUITS. LETTER AND NUMBER NOTATIONS IDENTIFY PANEL AND CIRCUIT NUMBERS. USE #12 CONDUCTORS, EXCEPT #10 CONDUCTORS SHALL BE INSTALLED IF DISTANCES EXCEED THOSE SPECIFIED IN THE ELECTRICAL SPECIFICATIONS. A-1,3,5 04 WIRING TURNED DOWN OR AWAY FROM OBSERVER. 03 WIRING TURNED UP OR TOWARDS OBSERVER. 02 WIRING. 01 WIRING METHODS 00 ACCESSIBLE DOOR ENTRY PUSH PLATE OPERATOR. HC 77 LP LIGHTING RELAY, CONTACTOR PANEL, OR DIMMING ENCLOSURE. 51 LIGHTING CONTROL STATION. 52 DIMMING ENTRY STATION OR CONTROL STATION, FLUSH MOUNTED. 53 SWITCH, TOGGLE MOTOR STARTER WITH OVERLOAD PROTECTION. ST 55 75 TRANSFORMER: NUMBER INDICATES kVA. 56 DISCONNECT SWITCH, UNFUSED. 42 DISCONNECT SWITCH, FUSED. 41 PUSHBUTTON. 45 PUSHBUTTONS, MOTOR CONTROL. 46 PANELBOARD CABINET, FLUSH MOUNTED. 47 PANELBOARD CABINET, SURFACE MOUNTED, 1 SECTION. 48 PANELBOARD CABINET, SURFACE MOUNTED, 2 SECTION. 49 DP#__ DISTRIBUTION PANEL OR SWITCHBOARD. 50 TRANSFER SWITCH (ONE-LINE DIAGRAM). 31 GENERATOR, POWER (ONE-LINE DIAGRAM). G 35 METER. M 36 VARIABLE FREQUENCY MOTOR CONTROLLER (ONE-LINE DIAGRAM). VFD VFC 38 CT CABINET PER UTILITY'S REQUIREMENTS (ONE-LINE DIAGRAM). 30 DETECTOR, FLOW SWITCH: FLOW SWITCHES SHALL BE PROVIDED AND INSTALLED WITH FIRE SPRINKLER SYSTEM AND SHALL BE CONNECTED TO LOCATIONS SHOWN ON THE FIRE SPRINKLER SHOP DRAWINGS. 35 DETECTOR, TAMPER SWITCH WITH VALVE: TAMPER SWITCHES SHALL BE PROVIDED AND INSTALLED WITH FIRE SPRINKLER SYSTEM AND SHALL BE CONNECTED TO LOCATIONS SHOWN ON THE FIRE SPRINKLER SHOP DRAWINGS. 36 FSD FIRE AND SMOKE DAMPER. 38 75 ALARM, HORN/STROBE, ONE ASSEMBLY, CEILING MOUNTED. SUBSCRIPT INDICATES CANDELA RATING. 42 75 ALARM, STROBE, CEILING MOUNTED. SUBSCRIPT INDICATES CANDELA RATING. 44 DETECTOR, SMOKE, DUCT WITH HOUSING AND SAMPLING TUBE. 22 DETECTOR, HEAT. 23 75 STROBE. SUBSCRIPT INDICATES CANDELA RATING. 26 WP ALARM, HORN/SPEAKER, WEATHERPROOF. 27 75 ALARM, HORN/STROBE, ONE ASSEMBLY. SUBSCRIPT INDICATES CANDELA RATING. 29 MAGNETIC DOOR HOLDER. 11 DETECTOR, SMOKE. 15 CONTROL MODULE. CM 07 MONITOR MODULE. MM 08 FIRE ALARM MANUAL PULL STATION. P 09 SHUT DOWN RELAY: INSTALL RELAY IN CONTROL CIRCUIT OF EQUIPMENT TO BE CONTROLLED IN THE EVENT OF A FIRE. R 10 FIRE ALARM 00 FIRE SYSTEM ANNUNCIATOR. FSA 01 FIRE ALARM CONTROL PANEL, SEMI-RECESSED. FCP 02 FIRE ALARM NOTIFICATION POWER SUPPLY. FPS 03 S SPEAKER, SURFACE. S 14 X TECHNOLOGY SYSTEM CABLE. SEE SPECIFIC JOB EQUIPMENT LIST FOR APPLICABLE DESIGNATIONS. EXAMPLES: C = CONTROL CABLE G = GROUND CABLE, 10 AWG, 1 CONDUCTOR, GREEN INSULATED M = MICROPHONE CABLE S = SPEAKER CABLE, 70 VOLT SYSTEM Z = SPEAKER CABLE, 8 OHM SYSTEM 01 TECHNOLOGY SYSTEMS 00 00 CCTV 03 CCTV CCTV HEADEND EQUIPMENT. 05 CCTV CAMERA/ENCLOSURE WITH LENS, TYPICAL. SEE SCHEDULE. 07 KEYPAD/CARD READER COMBINATION. KCR 06 CARD READER. CR 05 CARD ACCESS DOOR TYPE #1 OR AS NOTED. SEE SCHEDULE. #1 04 INTRUSION DETECTION HEADEND EQUIPMENT. SEC 03 SECURITY CONTROL PANEL. CTR 02 ACCESS CONTROL HEADEND EQUIPMENT. ACC 01 SECURITY CABLE. SEE EQUIPMENT SCHEDULE FOR CABLE TYPE. X 00 SECURITY 07 TV OUTLET. TV DISTRIBUTION 00
Transcript of 50 Ken Garff - Amazon S3 · mdp main distribution panel mg motor generator mh manhole min minimum...
-
324 S
. S
tate
St., S
uite 4
00
Salt L
ake C
ity, U
T 84111
800-6
78-7
077
801-3
28-5
151
fax: 801-3
28-5
155
ww
w.s
pectr
um
-engin
eers
.com
Ken G
arf
fA
uto
mo
tive
Gro
up
CO
PY
RIG
HT
ED
DO
CU
ME
NT
TH
IS D
RA
WIN
G A
ND
TH
E B
IM/C
AD
FIL
E F
RO
M W
HIC
H IT
HA
S B
EE
N G
EN
ER
AT
ED
AR
E P
RO
VID
ED
AS
AN
IN
ST
RU
ME
NT
OF
SE
RV
ICE
FO
R T
HIS
PR
OJE
CT
. T
HE
SE
DO
CU
ME
NT
S A
RE
TH
E S
OL
E P
RO
PE
RT
Y G
OR
EE
AR
CH
ITE
CT
S. A
NY
US
E O
F T
HE
SE
DO
CU
ME
NT
S, D
AT
A A
ND
DE
SIG
NS
FO
R P
UR
PO
SE
S O
TH
ER
TH
AN
TH
OS
E A
SS
OC
IAT
ED
WIT
H T
HIS
PR
OJE
CT
WIT
HO
UT
TH
E E
XP
RE
SS
ED
, W
RIT
TE
N P
ER
MIS
SIO
N O
F F
RE
D G
OR
EE
AR
CH
ITE
CT
S IS
PR
OH
IBIT
ED
.
Revis
ion
His
tory
:
Pro
ject
No
: 150
3
Da
te:
Mark
:
t. 71
3-66
0-61
0247
10 B
ella
ire B
lvd.
#10
5B
ella
ire, T
exas
774
01
GO
RE
EARCHITECTS
50
1963-2013
YEARS
11
/03
/15
DD
SE
T
DATE: 11/11/2015
SHEET INDEX,
ABBREVIATIONS,
AND GENERAL
NOTES
E-001
DO
WN
TO
WN
SA
LT
LA
KE
Jagu
ar
- L
an
d R
over
150 E
500 S
, S
AL
T L
AK
E C
ITY
, U
T 8
4111
A N
EW
AU
TO
MO
TIV
E F
AC
ILIT
Y D
ES
IGN
FO
R
ELECTRICAL SHEET INDEXE-001 SHEET INDEX, ABBREVIATIONS, AND GENERAL NOTES
E-100 POWER PLAN
E-101 MEZZANINE POWER PLAN
E-102 ROOF POWER PLAN
E-103 LIGHTING PLAN
E-104 MEZZANINE LIGHITNG PLAN
E-105 FIRE ALARM PLAN
E-106 MEZZANINE FIRE ALARM PLAN
E-107 TELECOM PLAN
E-108 MEZZANINE TELECOM PLAN
E-401 ENLARGED TELECOM PLANS
E-601 ONE-LINE DIAGRAM
E-602 FIRE ALARM RISER
E-603 EQUIPMENT SCHEDULE
E-604 INTERIOR LIGHTING FIXTURE SCHEDULE
E-605 PANEL SCHEDULES
E-606 PANEL SCHEDULES
E-607 TELECOM SCHEDULES AND NOTES
E-608 TELECOM RISER DIAGRAMS
E-701 TYPICAL MOUNTING HEIGHT DETAILS
GENERAL ELECTRICAL NOTES
3. EXPOSED STRUCTURE AREAS (EXCLUDING MECHANICAL, ELECTRICAL, ANDCOMMUNICATION SPACES): INSTALL RACEWAYS BETWEEN DECK AND STRUCTUREWHEREVER POSSIBLE IN EXPOSED STRUCTURE CEILING AREAS. ROUTERACEWAYS IN CONCEALED AREAS WHEREVER POSSIBLE. REFER ALL CONDITIONSWHERE RACEWAYS MUST BE INSTALLED WHICH CANNOT COMPLY WITH THESEREQUIREMENTS TO THE ARCHITECT.
4. SUBMITTALS: PROVIDE ORIGINAL ELECTRONIC PDF FORMAT, BOUND,BOOKMARKED (EACH SECTION AND PRODUCT), AND HIGHLIGHTED. JOB NAME ANDSUBCONTRACTOR SHALL BE ON THE FRONT COVER. PREPARE INDEX OFEQUIPMENT SUBMITTED IN EACH TAB.
5. REFLECTED CEILING PLANS: COORDINATE THE LOCATION OF LIGHT FIXTURESWITH THE ARCHITECTURAL REFLECTED CEILING PLANS. REFER ALLDISCREPANCIES TO THE ARCHITECT AND ENGINEER.
6. ALL WORK SHALL BE DONE ACCORDING TO THE CURRENT NATIONAL ELECTRICCODE (NEC), IBC, NFPA, AND IFC. COMPLIANCE AND FINAL APPROVAL IS SUBJECTTO THE ON SITE FIELD INSPECTION OF THE AHJ.
1. CLARIFICATION METHODS: AT THE TIME OF BIDDING, BIDDERS SHALL FAMILIARIZETHEMSELVES WITH THE DRAWINGS AND SPECIFICATIONS. ANY QUESTIONS,MISUNDERSTANDINGS, CONFLICTS, DELETIONS, DISCONTINUED PRODUCTS,CATALOG NUMBER DISCREPANCIES, DISCREPANCIES BETWEEN THE EQUIPMENTSUPPLIED AND THE INTENT OR FUNCTION OF THE EQUIPMENT, ETC, SHALL BESUBMITTED TO THE ARCHITECT/ENGINEER IN WRITING FOR CLARIFICATION PRIORTO ISSUANCE OF THE FINAL ADDENDUM AND BIDDING OF THE PROJECT. WHEREDISCREPANCIES OR MULTIPLE INTERPRETATIONS OCCUR, THE MOST STRINGENT(WHICH IS GENERALLY RECOGNIZED AS THE MOST COSTLY) THAT MEETS THEINTENT OF THE DOCUMENTS SHALL BE ENFORCED.
2. OWNER FURNISHED ITEMS: THE OWNER WILL FURNISH MATERIAL AND EQUIPMENTAS INDICATED IN THE CONTRACT DOCUMENTS TO BE INCORPORATED INTO THEWORK. THESE ITEMS ARE ASSIGNED TO THE INSTALLER AND COSTS FORRECEIVING, HANDLING, STORAGE, IF REQUIRED, AND INSTALLATION ARE INCLUDEDIN THE CONTRACT SUM.
A. THE INSTALLER'S RESPONSIBILITIES ARE THE SAME AS IF THE INSTALLERFURNISHED THE MATERIALS OR EQUIPMENT.
B. THE OWNER WILL ARRANGE AND PAY FOR DELIVERY OF OWNER FURNISHEDITEMS FREIGHT ON BOARD JOB SITE AND THE INSTALLER WILL INSPECTDELIVERIES FOR DAMAGE. IF OWNER FURNISHED ITEMS ARE DAMAGED,DEFECTIVE OR MISSING, DOCUMENT DAMAGED ITEMS WITH THETRANSPORT COMPANY AND THE OWNER WILL ARRANGEFOR REPLACEMENT. THE OWNER WILL ALSO ARRANGE FOR MANUFACTURER'S FIELD SERVICES, AND THE DELIVERY OFMANUFACTURER'S WARRANTIES AND BONDS TO THE INSTALLER.
C. THE INSTALLER IS RESPONSIBLE FOR DESIGNATING THE DELIVERY DATESOF OWNER FURNISHED ITEMS AND FOR RECEIVING, UNLOADING ANDHANDLING OWNER FURNISHED ITEMS AT THE SITE.THE INSTALLER IS RESPONSIBLE FOR PROTECTING OWNER FURNISHED ITEMS FROMDAMAGE, INCLUDING DAMAGE FROM EXPOSURE TO THE ELEMENTS, AND TO REPAIR OR REPLACE ITEMS DAMAGED AS A RESULT OF HISOPERATIONS.
DEFINITIONSNOTE: ALL DEFINITIONS MAY NOT BE USED.
INDICATED: THE TERM "INDICATED" REFERS TO GRAPHIC REPRESENTATIONS,NOTES, OR SCHEDULES ON THE DRAWINGS, OTHER PARAGRAPHS ORSCHEDULES IN THE SPECIFICATIONS, AND SIMILAR REQUIREMENTS IN THECONTRACT DOCUMENTS. WHERE TERMS SUCH AS "SHOWN", "NOTED","SCHEDULED", AND "SPECIFIED" ARE USED, IT IS TO HELP THE READERLOCATE THE REFERENCE, NO LIMITATION ON LOCATION IS INTENDED.
DIRECTED: TERMS SUCH AS "DIRECTED", "REQUESTED", AUTHORIZED","SELECTED", "APPROVED", "REQUIRED", AND "PERMITTED" MEAN "DIRECTED BYTHE ENGINEER", "REQUESTED BY THE ENGINEER", AND SIMILAR PHRASES.
APPROVED: THE TERM "APPROVED", WHERE USED IN CONJUNCTION WITH THEENGINEER'S ACTION ON THE CONTRACTOR'S SUBMITTALS, APPLICATIONS,AND REQUESTS, IS LIMITED TO THE ENGINEER'S DUTIES ANDRESPONSIBILITIES AS STATED IN GENERAL AND SUPPLEMENTARYCONDITIONS.
FURNISH: THE TERM "FURNISH" IS USED TO MEAN "SUPPLY AND DELIVER TOTHE PROJECT SITE, READY FOR UNLOADING, UNPACKING, ASSEMBLY,INSTALLATION, AND SIMILAR OPERATIONS."
INSTALL: THE TERM "INSTALL" IS USED TO DESCRIBE OPERATIONS ATPROJECT SITE INCLUDING THE ACTUAL "UNLOADING, UNPACKING, ASSEMBLY,ERECTION, PLACING, ANCHORING, APPLYING, WORKING TO DIMENSION,FINISHING, CURING, PROTECTING, CLEANING, AND SIMILAR OPERATIONS."
PROVIDE: THE TERM "PROVIDE" MEANS "TO FURNISH AND INSTALL,COMPLETE AND READY FOR THE INTENDED USE."
INSTALLER: AN "INSTALLER" IS THE CONTRACTOR OR AN ENTITY ENGAGED BYTHE CONTRACTOR, EITHER AS AN EMPLOYEE, SUBCONTRACTOR, OR SUB-SUBCONTRACTOR, FOR PERFORMANCE OF A PARTICULAR CONSTRUCTIONACTIVITY, INCLUDING INSTALLATION, ERECTION, APPLICATION, AND SIMILAROPERATIONS. INSTALLERS ARE REQUIRED TO BE EXPERIENCED IN THEOPERATIONS THEY ARE ENGAGED TO PERFORM.
TECHNOLOGY SYSTEMS: THE TERM "TECHNOLOGY SYSTEMS" IS USED TODESCRIBE ALL LOW VOLTAGE SYSTEMS GENERALLY REFERRED TO AS"SPECIAL SYSTEMS". THESE SYSTEMS INCLUDE BUT ARE NOT NECESSARILYLIMITED TO ALL SYSTEMS WHICH UTILIZE VOLTAGES OF LESS THAN 71VOLTS SUCH AS SOUND SYSTEMS, VIDEO SYSTEMS, TV SYSTEMS, SECURITYSYSTEMS, VOICE AND DATA CABLING SYSTEMS, ETC...
ABBREVIATIONSNOTE: ALL ABBREVIATIONS MAY NOT BE USED.
kVA KILOVOLT AMPERE
kVAR KILOVOLT AMPERE REACTIVE
kW KILOWATT
kWh KILOWATT HOUR
LED LIGHT EMITTING DIODE
LFMC LIQUID TIGHT FLEXIBLE METALCONDUIT
LFNC LIQUID TIGHT FLEXIBLENONMETALLIC CONDUIT
LPS LOW PRESSURE SODIUM
LRA LOCKED ROTOR AMPS
LTG LIGHTING
LV LOW VOLTAGE
MATV MASTER ANTENNA TELEVISIONSYSTEM
MAX MAXIMUM
MC METAL CLAD
MCA MINIMUM CIRCUIT AMPS
MCB MAIN CIRCUIT BREAKER
MCC MOTOR CONTROL CENTER
MCP MOTOR CIRCUIT PROTECTION
MDP MAIN DISTRIBUTION PANEL
MG MOTOR GENERATOR
MH MANHOLE
MIN MINIMUM
MLO MAIN LUGS ONLY
MOCP MAXIMUM OVERCURRENTPROTECTION
NA NOT APPLICABLE
NC NORMALLY CLOSED
NEC NATIONAL ELECTRICAL CODE
NEMA NATIOANL ELECTRICALMANUFACTURERSASSOCIATION
NFC NATIONAL FIRE CODE
NFPA NATIONAL FIRE PROTECTIONASSOCIATION
NIC NOT IN CONTRACT
NL NIGHT LIGHT
NO NORMALLY OPEN
NTS NOT TO SCALE
OC ON CENTER
OCP OVER CURRENT PROTECTION
OF/CI OWNER FURNISHED/CONTRACTOR INSTALLED
OF/OI OWNER FURNISHED/ OWNERINSTALLED
OFP OBTAIN FROM PLANS
OH DR OVERHEAD (COILING) DOOR
OL OVERLOAD
PB PUSHBUTTON
PF POWER FACTOR
PH PHASE
PNL PANEL
PT POTENTIAL TRANSFORMER
PTZ PAN/TILT/ZOOM
QTY QUANTITY
R REMOVE
RCP REFLECTED CEILING PLAN
RMC RIGID METAL CONDUIT
RNC RIGID NONMETAL CONDUIT
RPM REVOLUTIONS PER MINUTE
RR REMOVE AND RELOCATE
S/S START/STOP
SCA SHORT CIRCUIT AMPS
SCBA STANDARD COLOR ASSELECTED BY ARCHITECT
SF SQUARE FOOT (FEET)
SFBA STANDARD FINISH ASSELECTED BY ARCHITECT
SPDT SINGLE POLE, DOUBLE THROW
SPEC SPECIFICATION
SPST SINGLE POLE, SINGLE THROW
ST SINGLE THROW
SWBD SWITCHBOARD
SWGR SWITCHGEAR
TL TWIST LOCK
TP TELEPHONE POLE
TP TWISTED PAIR
TTB TELEPHONE TERMINAL BOARD
TV TELEVISION
TVSS TRANSIENT VOLTAGE SURGESUPPRESSER
TYP TYPICAL
UF UNDERFLOOR
UGND UNDERGROUND
UPS UNINTERRUPTIBLE POWERSUPPLY
V VOLTS
VA VOLT AMPERE
VFC/VFD VARIABLE FREQUENCY MOTORCONTROLLER
W/ WITH
W/O WITHOUT
WP WEATHERPROOF
XFMR TRANSFORMER
1P SINGLE POLE
1PH SINGLE-PHASE
1WAY ONE-WAY
2/C TWO-CONDUCTOR
2WAY TWO-WAY
3/C THREE-CONDUCTOR
3WAY THREE-WAY
4OUT QUADRUPLE RECEPTACLEOUTLET
4PDT FOUR-POLE DOUBLE THROW
4PST FOUR-POLE SINGLE THROW
4W FOUR-WIRE
4WAY FOUR-WAY
A ABOVE COUNTER
AC ARMORED CABLE
ADA AMERICANS WITH DISABILITIESACT
ADJ ADJACENT
AFF ABOVE FINISHED FLOOR
AFG ABOVE FINISHED GRADE
AIC AMPERE INTERRUPTINGCAPACITY
ALUM ALUMINUM
AMP AMPERE
ANN ANNUNCIATOR
AP ACCESS POINT (WIRELESSDATA)
AR AS REQUIRED
ASC AMPS SHORT CIRCUIT
ATS AUTOMATIC TRANSFER SWITCH
AV AUDIO VISUAL
AWG AMERICAN WIRE GAGE
BBXFMR
BUCK-BOOST TRANSFORMER
C CEILING MOUNTED
CATV COMMUNITY ANTENNATELEVISION
CB CIRCUIT BREAKER
CCBA CUSTOM COLOR AS SELECTEDBY ARCHITECT
CCTV CLOSED CIRCUIT TELEVISION
CF/CI CONTRACTOR FURNISHED/CONTRACTOR INSTALLED
CF/OI CONTRACTOR FURNISHED/OWNER INSTALLED
CFBA CUSTOM FINISH AS SELECTEDBY ARCHITECT
CKT CIRCUIT
CM CONSTRUCTION MANAGER
CND CONDUIT
CO CONVENIENCE OUTLET
COR CONTRACTING OFFICER'SREPRESENTATIVE
CP CONTROL PANEL
CT CURRENT TRANSFORMER
CTV CABLE TELEVISION
CU COPPER
dBA UNIT OF SOUND LEVEL
DPDT DOUBLE POLE, DOUBLE THROW
DS DISCONNECT SWITCH
EA EACH
EM EMERGENCY
EMT ELECTRICAL METALLIC TUBING
ENT ELECTRIC NONMETALLICTUBING
EPO EMERGENCY POWER OFF
EQUIP EQUIPMENT
EX EXISTING
F FURNITURE MOUNTED
FA FIRE ALARM
FCP FIRE ALARM CONTROL PANEL
FLA FULL LOAD AMPS
FMC FLEXIBLE METAL CONDUIT
FOB FREIGHT ON BOARD
FVNR FULL VOLTAGENON-REVERSING
FVR FULL VOLTAGE REVERSING
G GROUND
GEN GENERATOR
GFCI GROUND FAULT INTERRUPTER
GFP GROUND FAULT PROTECTION
HD HEAVY DUTY
HID HIGH INTENSITY DISCHARGE
HOA HAND-OFF-AUTOMATIC
HP HORSE POWER
HPF HIGH POWER FACTOR
HPS HIGH PRESSURE SODIUM
HV HIGH VOLTAGE
HZ HERTZ
I/O INPUT/ OUTPUT
IG ISOLATED GROUND
IMC INTERMEDIATE METALCONDUIT
IN/IS INSULATED/ ISOLATED
IR INFRARED
J-BOX JUNCTION BOX
kV KILOVOLT
SYMBOL DESCRIPTION
SYMBOLS LEGENDSYMBOL DESCRIPTION
SYMBOLS LEGENDSYMBOL DESCRIPTION
SYMBOLS LEGEND
SWITCH, TIMER OPERATED.T50
SWITCH, DOUBLE POLE ("x" INDICATES FIXTURES CONTROLLED).X2
41
SWITCH, THREE-WAY ("x" INDICATES FIXTURES CONTROLLED).X3
42
SWITCH, FOUR-WAY ("x" INDICATES FIXTURES CONTROLLED).X4
43
SWITCH, KEY OPERATED.K45
FLUSH FLOOR BOX. "#" SHOWN ON DRAWINGS. REFER TOWIRING DEVICE SCHEDULE IN THE ELECTRICAL SPECIFICATIONSFOR CONFIGURATION AND DEVICES.
FB#
36
POWER POLE. "#" SHOWN ON DRAWINGS. REFER TO WIRINGDEVICE SCHEDULE IN THE ELECTRICAL SPECIFICATIONS FORCONFIGURATION AND DEVICES.
PP#
37
FLUSH FIRE RATED POKE THRU. "#" SHOWN ON DRAWINGS.REFER TO WIRING DEVICE SCHEDULE IN THE ELECTRICALSPECIFICATIONS FOR CONFIGURATION AND DEVICES.
PT#
38
SWITCH, DIMMER.D39
SWITCH, SINGLE POLE ("x" INDICATES FIXTURES CONTROLLED).X40
R RECEPTACLE, RANGE: NEMA 14-50R.31
DROP CORD. SEE DETAIL.D34
RECEPTACLE, QUADRAPLEX: NEMA 5-20R.22
RECEPTACLE, QUADRAPLEX WITH GROUND FAULT CIRCUITINTERRUPTER: NEMA 5-20R.
27
RECEPTACLE, SPECIAL PURPOSE. PROVIDE RECEPTACLE TOMATCH EQUIPMENT PLUG.
28
RECEPTACLE, DUPLEX, WEATHERPROOF: NEMA 5-20R.WP
11
RECEPTACLE, DUPLEX ON EMERGENCY POWER: NEMA 5-20R.13
RECEPTACLE, DUPLEX WITH GROUND FAULT CIRCUITINTERRUPTER: NEMA 5-20R.
16
RECEPTACLE, DUPLEX WITH GROUND FAULT CIRCUITINTERRUPTER, WEATHERPROOF: NEMA 5-20R.WP
19
RECEPTACLE, DUPLEX WITH GROUND FAULT CIRCUITINTERRUPTER, WET LABEL, "WEATHERPROOF IN USE":NEMA 5-20R.W
10
S RECEPTACLE, DUPLEX, SWITCHED: NEMA 5-20R.08
DF
RECEPTACLE, DUPLEX WITH GROUND FAULT CIRCUIT INTERRUPTER,DRINKING FOUNTAIN: CONCEAL WATER COOLER RECEPTACLEBEHIND WATER COOLER. SEE MECHANICAL/PLUMBING SHOPDRAWINGS FOR INSTALLATION REQUIREMENTS.
06
RECEPTACLE, DUPLEX, DEDICATED CIRCUIT: NEMA 5-20R.D
05
RECEPTACLE, DUPLEX, CEILING: NEMA 5-20R.C
04
RECEPTACLE, DUPLEX, ABOVE COUNTER: NEMA 5-20R.A
03
RECEPTACLE, DUPLEX: NEMA 5-20R.02
WIRING DEVICES00
SITE ELECTRICAL AND COMMUNICATIONS UTILITIES00
UTILITY POLE.03
TRANSFORMER.T17
PANELBOARD WITH MAIN LUGS ONLY. BUS SIZE AND PHASE ASSHOWN (ONE-LINE DIAGRAM).
225/3
"1H"
23
PANELBOARD (ONE-LINE DIAGRAM)."1H"
22
PANELBOARD WITH MAIN CIRCUIT BREAKER. SIZE AND PHASE ASSHOWN (ONE-LINE DIAGRAM).
225/3
"1H"
24
PANELBOARD WITH MAIN AND SUB FEED CIRCUIT BREAKER(ONE-LINE DIAGRAM).
60/3
225/3
"1H"
25
TRANSFORMER (ONE-LINE DIAGRAM).
16
MOTOR.12
CIRCUIT BREAKER, SOLID STATE WITH GROUND FAULTPROTECTION (ONE-LINE DIAGRAM).
GFP
11
CIRCUIT BREAKER, SOLID STATE (ONE-LINE DIAGRAM).
10
CIRCUIT BREAKER, MOLDED CASE (ONE-LINE DIAGRAM).
07
CIRCUIT BREAKER, MOLDED CASE WITH SHUNT TRIP(ONE-LINE DIAGRAM).
08
DISCONNECT, FUSED (ONE-LINE DIAGRAM).
02
ELECTRICAL POWER AND DISTRIBUTION00
EXIT SIGN: DOUBLE FACE; WALL MOUNTED10
EXIT SIGN: SINGLE FACE; CEILING MOUNTED07
EXIT SIGN: DOUBLE FACE; CEILING MOUNTED09
EXIT SIGN: SINGLE FACE; WALL MOUNTED08
LIGHTING (REFER TO FIXTURE SCHEDULE FOR SYMBOLS)00
FIXTURE IDENTIFICATION: (W-3) INDICATES FIXTURE TYPE ASSCHEDULED.
(W-3)01
FIXTURE IDENTIFICATION, EMERGENCY WITH BATTERY PACK,CONNECTED TO GENERATOR AS INDICATED: (W-3) INDICATESFIXTURE TYPE AS SCHEDULED.
(W-3)02
EM EMERGENCY.03
NL NIGHT LIGHT: DO NOT SWITCH.04
EGRESS DIRECTION ARROW (EXIT SIGNS).05
VACANCY SENSOR, DUAL TECHNOLOGY, WALL.07
VACANCY SENSOR, DUAL TECHNOLOGY,OMNI-DIRECTIONAL, CEILING.
06
LIGHTING CONTROL00
OCCUPANCY SENSOR, DUAL TECHNOLOGY,OMNI-DIRECTIONAL, CEILING.
01
OCCUPANCY SENSOR, DUAL TECHNOLOGY, WALL.02
OCCUPANCY SENSOR, DUAL TECHNOLOGY, DIRECTIONAL.03
PHOTOCELL.P08
STRUCTURED CABLING00
TELEPHONE, WALL MOUNTED ("X" INDICATES QUANTITY OFCABLES).
X01
TELEPHONE, WALL MOUNTED: WALL PHONE.W03
OUTLET, DATA COMMUNICATION ("X" INDICATES QUANTITY OFCABLES).
X04
OUTLET, BUILDING STANDARD COMBINATION TELEPHONE/ DATACOMMUNICATION.
05
TELEPHONE TERMINAL BOARD, FIRE TREATED PLYWOODPAINTED.
07
LAN RACK, FLOOR STANDING.08
09
CONTRACT LIMIT LINE: DASHDOT, WIDE LINE.17
PROPERTY LINE: DASHED, WIDE LINE.16
HIDDEN FEATURES LINE: HIDDEN, THIN LINE13
NEW LINE: MEDIUM LINE.12
MATCH LINE INDICATOR: CENTER, EXTRA WIDE LINE.MATCH LINE
SEE XX/X-XXX
11
BREAK, ROUND10
BREAK, STRAIGHT: TO BREAK PARTS OF DRAWING09
CU-1 EQUIPMENT INDICATOR.07
REVISION INDICATOR.106
KEYNOTE INDICATOR.105
ROOM IDENTIFIER WITH ROOM NAME AND NUMBER.ROOM NAME
10004
ELEVATION OR SECTION INDICATOR, EXTERIOR: A5 INDICATESELEVATION OR SECTION NUMBER, E-201 INDICATES DRAWINGSHEET WHERE ELEVATION OR SECTION IS SHOWN.
A5
E-201
02
DETAIL INDICATOR: A5 INDICATES DETAIL NUMBER, E-501INDICATES DRAWING SHEET WHERE DETAIL IS SHOWN.
A5
E-501
01
REFERENCE AND LINE SYMBOLS00
MECHANICAL EQUIPMENT CONNECTION. REFER TO EQUIPMENTSCHEDULE FOR REQUIREMENTS.
25
JUNCTION BOX, CEILING.CJ22
EARTH GROUND (ONE-LINE DIAGRAM).21
CABLE TRAY ABOVE ACCESSIBLE CEILING.C C19
PULL BOX.PB18
JUNCTION BOX, SECURITY SYSTEM. PROVIDE CONDUIT ANDROUGH-IN PER SECURITY DRAWINGS.SE
J15
JUNCTION BOX, SYSTEMS FURNITURE COMMUNICATIONCONNECTION.SC
J14
JUNCTION BOX.J13
ADA ACCESS PUSH PLATEHC12
CONDUCTOR & CONDUIT ("CC") SCHEDULE INDICATOR. REFERTO ONE-LINE DIAGRAM.
111
CONDUIT STUB. DIMENSION RECORD DRAWINGS AND MARK.10
LOW VOLTAGE WIRING: DIVIDE, MEDIUM LINE.09
WIRING AND/OR RACEWAY: THIN LINE. WHERE "X" = :
CATV = CABLE TELEVISION NC = NURSE CALL
CCTV = CLOSED CIRCUIT P = POWER
TELEVISION RC = RIGID CONDUIT
FA = FIRE ALARM S = SOUND
FO = FIBER OPTICS T = TELEPHONE
I = INTERCOM TV = TELEVISION
OTHERS AS NOTED IN OTHER SCHEDULES. RACEWAYS ANDWIRING SHALL BE SIZED AS SHOWN AND/OR SPECIFIED.
X
08
BRANCH CIRCUIT HOME RUN TO PANELBOARD: NUMBER OFARROWS INDICATES NUMBER OF CIRCUITS. LETTER ANDNUMBER NOTATIONS IDENTIFY PANEL AND CIRCUIT NUMBERS.SMALL CROSS LINES INDICATE NUMBER OF CONDUCTORS ORCABLES. LARGER CROSS LINE INDICATES EQUIPMENT GROUND.WAVY CROSS LINE INDICATES INSULATED/ ISOLATED GROUND.FOR BRANCH WIRING, CROSS LINES INDICATE #12 CONDUCTORS,EXCEPT #10 CONDUCTORS SHALL BE INSTALLED IF DISTANCESEXCEED THOSE SPECIFIED IN THE ELECTRICAL SPECIFICATIONS.
A-1,3,5
06
BRANCH CIRCUIT HOME RUN TO PANELBOARD: NUMBER OFARROWS INDICATES NUMBER OF CIRCUITS. LETTER ANDNUMBER NOTATIONS IDENTIFY PANEL AND CIRCUIT NUMBERS.NUMBER IN BOX REFERS TO THE CONDUCTOR AND CONDUITSCHEDULE. FOR BRANCH WIRING USE #12 CONDUCTORS,EXCEPT #10 CONDUCTORS SHALL BE INSTALLED IF DISTANCESEXCEED THOSE SPECIFIED IN THE ELECTRICALSPECIFICATIONS.
A-1,3,5
1
05
BRANCH CIRCUIT HOME RUN TO PANELBOARD: NUMBER OFARROWS INDICATES NUMBER OF CIRCUITS. LETTER ANDNUMBER NOTATIONS IDENTIFY PANEL AND CIRCUIT NUMBERS.USE #12 CONDUCTORS, EXCEPT #10 CONDUCTORS SHALL BEINSTALLED IF DISTANCES EXCEED THOSE SPECIFIED IN THEELECTRICAL SPECIFICATIONS.
A-1,3,5
04
WIRING TURNED DOWN OR AWAY FROM OBSERVER.03
WIRING TURNED UP OR TOWARDS OBSERVER.02
WIRING.01
WIRING METHODS00
ACCESSIBLE DOOR ENTRY PUSH PLATE OPERATOR.HC77
LPLIGHTING RELAY, CONTACTOR PANEL, OR DIMMING ENCLOSURE.
51
LIGHTING CONTROL STATION.52
DIMMING ENTRY STATION OR CONTROL STATION, FLUSHMOUNTED.
53
SWITCH, TOGGLE MOTOR STARTER WITH OVERLOADPROTECTION.ST
55
75 TRANSFORMER: NUMBER INDICATES kVA.56
DISCONNECT SWITCH, UNFUSED.42
DISCONNECT SWITCH, FUSED.41
PUSHBUTTON.45
PUSHBUTTONS, MOTOR CONTROL.46
PANELBOARD CABINET, FLUSH MOUNTED.47
PANELBOARD CABINET, SURFACE MOUNTED, 1 SECTION.48
PANELBOARD CABINET, SURFACE MOUNTED, 2 SECTION.49
DP#__DISTRIBUTION PANEL OR SWITCHBOARD.
50
TRANSFER SWITCH (ONE-LINE DIAGRAM).
31
GENERATOR, POWER (ONE-LINE DIAGRAM).G35
METER.M36
VARIABLE FREQUENCY MOTOR CONTROLLER (ONE-LINEDIAGRAM).
VFDVFC38
CT CABINET PER UTILITY'S REQUIREMENTS (ONE-LINE DIAGRAM).
30
DETECTOR, FLOW SWITCH: FLOW SWITCHES SHALL BEPROVIDED AND INSTALLED WITH FIRE SPRINKLER SYSTEMAND SHALL BE CONNECTED TO LOCATIONS SHOWN ONTHE FIRE SPRINKLER SHOP DRAWINGS.
35
DETECTOR, TAMPER SWITCH WITH VALVE: TAMPER SWITCHESSHALL BE PROVIDED AND INSTALLED WITH FIRE SPRINKLERSYSTEM AND SHALL BE CONNECTED TO LOCATIONS SHOWN ONTHE FIRE SPRINKLER SHOP DRAWINGS.
36
FSD
FIRE AND SMOKE DAMPER.
38
75ALARM, HORN/STROBE, ONE ASSEMBLY, CEILING MOUNTED. SUBSCRIPT INDICATES CANDELA RATING.
42
75ALARM, STROBE, CEILING MOUNTED. SUBSCRIPTINDICATES CANDELA RATING.
44
DETECTOR, SMOKE, DUCT WITH HOUSING AND SAMPLING TUBE.
22
DETECTOR, HEAT.23
75 STROBE. SUBSCRIPT INDICATES CANDELA RATING.26
WP ALARM, HORN/SPEAKER, WEATHERPROOF.27
75ALARM, HORN/STROBE, ONE ASSEMBLY. SUBSCRIPTINDICATES CANDELA RATING.
29
MAGNETIC DOOR HOLDER.11
DETECTOR, SMOKE.15
CONTROL MODULE.CM07
MONITOR MODULE.MM08
FIRE ALARM MANUAL PULL STATION.P09
SHUT DOWN RELAY: INSTALL RELAY IN CONTROL CIRCUITOF EQUIPMENT TO BE CONTROLLED IN THE EVENT OF AFIRE.
R
10
FIRE ALARM00
FIRE SYSTEM ANNUNCIATOR.FSA01
FIRE ALARM CONTROL PANEL, SEMI-RECESSED.FCP02
FIRE ALARM NOTIFICATION POWER SUPPLY.FPS03
SSPEAKER, SURFACE.S
14
X
TECHNOLOGY SYSTEM CABLE. SEE SPECIFIC JOB EQUIPMENTLIST FOR APPLICABLE DESIGNATIONS.
EXAMPLES:C = CONTROL CABLEG = GROUND CABLE, 10 AWG, 1 CONDUCTOR, GREEN
INSULATEDM = MICROPHONE CABLES = SPEAKER CABLE, 70 VOLT SYSTEMZ = SPEAKER CABLE, 8 OHM SYSTEM
01
TECHNOLOGY SYSTEMS00
00CCTV
03CCTV CCTV HEADEND EQUIPMENT.
05CCTV CAMERA/ENCLOSURE WITH LENS, TYPICAL. SEE SCHEDULE.
07KEYPAD/CARD READER COMBINATION.KCR
06CARD READER.CR
05 CARD ACCESS DOOR TYPE #1 OR AS NOTED. SEESCHEDULE.
#1
04INTRUSION DETECTION HEADEND EQUIPMENT.SEC
03SECURITY CONTROL PANEL.CTR
02ACCESS CONTROL HEADEND EQUIPMENT.ACC
01 SECURITY CABLE. SEE EQUIPMENT SCHEDULE FOR CABLETYPE.
X
00SECURITY
07TV OUTLET.
TV DISTRIBUTION00
-
J
EXISTING VOLVO FACILITY
NOT IN SCOPE OF WORK
ST
AT
E S
TR
EE
T
EXISTING JAGUAR FACILITY
NOT IN SCOPE OF WORK
SO
UT
H 2
00 E
AS
T
500 SOUTH
EAST 600 SOUTH
EXISTING MERCEDES-BENZ FACILITY
NOT IN SCOPE OF WORK
EXISTING CAR WASH
NOT IN SCOPE OF WORK
EXISTING MERCEDES-BENZ
CERTIFIED PRE-OWNEDFACILITY
NOT IN SCOPE OF WORK
EXISTING FIAT FACILITY
NOT IN SCOPE OF WORK
JAGUAR / LAND ROVEROF DOWNTOWN SALT LAKE
LAND ROVER
SHOWROOM
JAGUAR
SHOWROOM
PARTS
RECIEVING
SERVICE
CENTER
MAKE-READY
SERVICE
RECEPTION
(PL-1)(PL-1)(PL-1)(PL-1)(PL-1)(PL-1)
(PL-2)(PL-2) (PL-2)
(PL-2) (PL-2) (PL-2)
(PL-2)
(PL-2)
(PL-2)
(PL-2)
1
1RB1RB1RB
777
77 7
7
1RB-9 1RB-10 1RB-11
1RB-12
1RB-13 1RB-141RB-15
EXISTING 4" CONDUIT FROM DATACENTER STUBBED. NEED TO TIE IN4" CONDUIT FROM IT ROOM
NEW 4" CONDUIT
324 S
. S
tate
St., S
uite 4
00
Salt L
ake C
ity, U
T 84111
800-6
78-7
077
801-3
28-5
151
fax: 801-3
28-5
155
ww
w.s
pectr
um
-engin
eers
.com
Ken G
arf
fA
uto
mo
tive
Gro
up
CO
PY
RIG
HT
ED
DO
CU
ME
NT
TH
IS D
RA
WIN
G A
ND
TH
E B
IM/C
AD
FIL
E F
RO
M W
HIC
H IT
HA
S B
EE
N G
EN
ER
AT
ED
AR
E P
RO
VID
ED
AS
AN
IN
ST
RU
ME
NT
OF
SE
RV
ICE
FO
R T
HIS
PR
OJE
CT
. T
HE
SE
DO
CU
ME
NT
S A
RE
TH
E S
OL
E P
RO
PE
RT
Y G
OR
EE
AR
CH
ITE
CT
S. A
NY
US
E O
F T
HE
SE
DO
CU
ME
NT
S, D
AT
A A
ND
DE
SIG
NS
FO
R P
UR
PO
SE
S O
TH
ER
TH
AN
TH
OS
E A
SS
OC
IAT
ED
WIT
H T
HIS
PR
OJE
CT
WIT
HO
UT
TH
E E
XP
RE
SS
ED
, W
RIT
TE
N P
ER
MIS
SIO
N O
F F
RE
D G
OR
EE
AR
CH
ITE
CT
S IS
PR
OH
IBIT
ED
.
Revis
ion
His
tory
:
Pro
ject
No
: 150
3
Da
te:
Mark
:
t. 71
3-66
0-61
0247
10 B
ella
ire B
lvd.
#10
5B
ella
ire, T
exas
774
01
GO
RE
EARCHITECTS
50
1963-2013
YEARS
11
/03
/15
DD
SE
T
DATE: 11/11/2015
ELECTRICAL SITE
PLAN
ES101
DO
WN
TO
WN
SA
LT
LA
KE
Jagu
ar
- L
an
d R
over
150 E
500 S
, S
AL
T L
AK
E C
ITY
, U
T 8
4111
A N
EW
AU
TO
MO
TIV
E F
AC
ILIT
Y D
ES
IGN
FO
R
SCALE: 1" = 30'-0"1ELECTRICAL SITE PLAN
SHEET KEYNOTES1 INTERCEPT (12) EXISTING SITE LIGHTING CIRCUITS IN JUNCTION BOX (CONCRETE
PRE-CAST BOX) AND EXTEND, USING WATER-TIGHT CONNECTIONS, TO RELAY PANEL"1RB". USE #8 WIRING IN 1"C.
-
J J J J J J J
J J J J J
JJ
J
J
ST
ST ST
ST
ST
ST ST ST
ST
ST
ST
ST ST
ST
ST
2
2
2ST
ST
ST ST ST
ST
2
J J J
J
J
J
J
JJ J J
J J
J
J J
J
J
J
J
J
JJ
JJ
J
C
C
E
E
F
F
G
G
H
H
2 2
4 4
3 3
LAND
ROVER
SALES
105
JAGUAR
SALES
104
CONF. /
TRAINING
110
BREAK
ROOM
120
JANITOR
122
HOSPITALITY
114
RECEPTION
101
OIL WASTE
152
MEN
121
STORAGE
159
WOMEN
123
CUSTOMER
LOUNGE
102
STORAGE
109
STORAGE
108
OIL /
COMPRESSOR-1
156-1
RISER
153
YARD
EQUIPMENT
154
PRE-OWNED
MANAGER
118
SALES
MANAGER
117
SALES
MANAGER
116
SERVICE
MANAGER
126
WARRANTY
129
RETAIL
PARTS
128
LAND
ROVER
SHOWROOM
106
JAGUAR
SHOWROOM
103
INTERNET
119
RETAIL
DISPLAY
127
ELECTRICAL
157
OIL /
COMPRESSOR-2
156-2
CORRIDOR
148
WOMEN
148A
SERVICE
SHOP
151
TECH
PARTS
142
SPECIAL
TOOLS
143
PARTS
MANAGER
130
WASH
ROOM
146LOCKER
145A
MEN
145
PARTS
STORAGE
147APARTS
RECIEVING
147C
BREAKROOM
149
CENTER
MGR.
113
F&I
112
F&I
111
NEW CAR
DELIVERY
107
USED TIRES
150
DETAIL
BAYS
158
COLOR /
TRIM
115
VESTIBULE
100
SERVICE
RECEPTION
125
SERVICE
ADVISORS
124
DF DF
A
AA
A
A
A A
REF
A
A
A
REF
A
A
DFDF
FB2 FB2 FB2 FB2 FB2FB2FB2FB2
FB2 FB
2
FB
2
FB
2
FB
2
FB
2
FB
2
FB
2F
B2
FB
2F
B2
FB2
FB2
FB2
AA A A A A
AA
A A AA A A
A
A
A
AA
AA
AA
1
AA
AA
AA
1
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
A
1 1 1 1 1
AA
AAAA A
AA
AA
AA
AA
AAA AA
AA
AA
AA
AAAA
1 1 1 1 1
L6-20R
L6-20RL6-20R
L6-20R
2
"MDP"
"LDP"
"ML1"
"ML2"
"1LA"
"1HA""1RA"
33
FB2 FB2
"CTE"
"T1"
EXISTING TRANSFORMER
1LB-11LB-2
1LB-31LB-4
1LB-5
1LB-6
1LB-71LB-8
1LB-91LB-10 1LB-11
1LB-12
1LB-14
1LB-15
1LB-16 4
4
1LB-17
1LB-18
1LB-19
"PARTS-L"
PARTS-L-1
PARTS-L-17
PARTS-L-3
PARTS-L-4PARTS-L-5
PARTS-L-6
A
1LB-13
1LB-20
1LB-21
1LB-22
1LB-23
1LB-24
5
6 6 6
6
6
ML3-14
ML3-13
1LB-25
1LB-28
1LB-27
1LB-30
1LB-291LB-32
1LB-31 1LB-34 1LB-33
1LB-36
1LB-35
1LB-38
1LB-37
1LB-39
1LB-42
1LB-41
7 7 7 7
1LB-40
1LB-44
1LB-43
1LB-46
"PARTS-H"
ML2-19
1LA-1
1LA-2 1LA1LA-4
1LA-31LA-61LA-51LA-8
1LB-45
1LB-48
1LB-47
1LB-501LB-49
ML3-9 ML3-10ML3-11
ML3-12
ML3-5
1LB-51
ML3-6 ML3-7 ML3-8
A
1LA-71LA-101LA-9
UH-1PARTS-L-11
RH-5PARTS-L-9
ML1-3,5ML1-2
ML1-4,6
ML1-7ML1-8,10ML1-9
ML1-11,13ML1-12ML1-14,16
ML1-15
ML1-17
1LA-12
1LA-11
ML1-18
ML1-19,21
1LA
1LA-13
1LA-14
ML1-20
ML1-22,24
ML1-23
ML1-25,27
1LA-15 1LA-16
ML1-26,28
7
ML1-1
ML1-29
ML1-30,32
ML1-31,33
ML1-34
ML1-35
ML1-36,38
ML1-37,39
ML1-401LA-17
1LA-18 1LA-19 1LA-20
ML1-41
ML1-42,44
ML1-43
ML1-45,47
1LA-21 1LA-22
ML1-46ML1-48,50
ML1-49
ML1-51,53
1LA-23
1LB-611LB-63
1LB-651LB-67
1LB-69
1LB-58
1LA
ML2-1
ML2-2 ML2-3ML2-4
ML2-5 ML2-6
ML2-7
ML2-8
ML2-8 ML2-9
ML2-10
ML2-11
ML2-12 ML2-13
1LA-24
1LA
UH-1PARTS-L-11
RH-3ML3-2
RH-3ML3-3
RH-3ML3-4
RH-2ML2-16
RH-4ML2-15
RH-2ML2-14
RH-2ML2-17
RH-2ML2-17
RH-2ML2-18
RH-4ML2-20
UH-3ML2-29,31
UH-3ML2-25,27
UH-2ML2-21,23
RH-2ML2-22
RH-1ML2-22
RH-2ML2-24
RH-2ML2-24
RH-1ML2-26
RH-1ML2-28
UH-3ML2-30,32
8
1RB
8
1RB
8
1RB
8
1RB
8
1RB
8
1RB99
1LB-26
99
1LB-60
999
1LB-62
C
9
9
PARTS-L-15 PARTS-L-2
9
1LB-64
9
FB
2 10
+42"+42"
+42"+42"
1LA-25
EXISTING
324 S
. S
tate
St., S
uite 4
00
Salt L
ake C
ity, U
T 84111
800-6
78-7
077
801-3
28-5
151
fax: 801-3
28-5
155
ww
w.s
pectr
um
-engin
eers
.com
Ken G
arf
fA
uto
mo
tive
Gro
up
CO
PY
RIG
HT
ED
DO
CU
ME
NT
TH
IS D
RA
WIN
G A
ND
TH
E B
IM/C
AD
FIL
E F
RO
M W
HIC
H IT
HA
S B
EE
N G
EN
ER
AT
ED
AR
E P
RO
VID
ED
AS
AN
IN
ST
RU
ME
NT
OF
SE
RV
ICE
FO
R T
HIS
PR
OJE
CT
. T
HE
SE
DO
CU
ME
NT
S A
RE
TH
E S
OL
E P
RO
PE
RT
Y G
OR
EE
AR
CH
ITE
CT
S. A
NY
US
E O
F T
HE
SE
DO
CU
ME
NT
S, D
AT
A A
ND
DE
SIG
NS
FO
R P
UR
PO
SE
S O
TH
ER
TH
AN
TH
OS
E A
SS
OC
IAT
ED
WIT
H T
HIS
PR
OJE
CT
WIT
HO
UT
TH
E E
XP
RE
SS
ED
, W
RIT
TE
N P
ER
MIS
SIO
N O
F F
RE
D G
OR
EE
AR
CH
ITE
CT
S IS
PR
OH
IBIT
ED
.
Revis
ion
His
tory
:
Pro
ject
No
: 150
3
Da
te:
Mark
:
t. 71
3-66
0-61
0247
10 B
ella
ire B
lvd.
#10
5B
ella
ire, T
exas
774
01
GO
RE
EARCHITECTS
50
1963-2013
YEARS
11
/03
/15
DD
SE
T
DATE: 11/11/2015
POWER PLAN
E-100
DO
WN
TO
WN
SA
LT
LA
KE
Jagu
ar
- L
an
d R
over
150 E
500 S
, S
AL
T L
AK
E C
ITY
, U
T 8
4111
A N
EW
AU
TO
MO
TIV
E F
AC
ILIT
Y D
ES
IGN
FO
R
GENERAL SHEET NOTES
SHEET KEYNOTES1 POWER FOR LIFTS SHALL RUN FROM JUNCTION BOX IN THE CEILING WITH FLEX
CONDUIT DOWN TO THE LIFT POWER INPUT. COORDINATE ROUGH-IN LOCATION WITHMANUFACTURER'S SHOP DRAWINGS PRIOR TO ROUGH-IN.
2 RUN CONDUIT UNDER SLAB, NOT OVERHEAD IN THIS AREA.
3 PROVIDE CONNECTIONS TO HAND DRYERS. COORDINATE ROUGH-IN LOCATION WITHARCHITECTURAL DRAWINGS.
4 PROVIDE CONNECTIONS TO MOTORIZED SCREEN. VERIFY LOCATION OF SCREEN ANDSWITCH WITH ARCHITECTURAL DRAWINGS AND PROVIDE CONNECTIONS BETWEENTHE TWO.
5 PROVIDE 8 SWITCHES IN HORIZONTAL LINE-UP IN THE WALL WITH ENGRAVED LABELSBELOW THE SWITCHES. LABELS SHALL READ AS FOLLOWS. 'FAN HEAT'. 'FAN COOL'.'PUMP COOL'. 'FAN COOL'. 'PUMP COOL'. 'FAN COOL'. 'PUMP COOL'. 'FAN HEAT'. SEEMECHANICAL CONTROL SCHEMATIC AND PROVIDE ALL WORK DESIGNATED TO BEPERFORMED BY DIVISION 26.
6 PROVIDE 2 SWITCHES IN HORIZONTAL LINE-UP IN THE WALL WITH ENGRAVED LABELSBELOW THE SWITCH. ENGRAVED LABELS SHALL READ 'FAN COOL'. 'PUMP COOL'. SEEMECHANICAL CONTROL SCHEMATIC AND PROVIDE ALL WORK DESIGNATED TO BEPERFORMED BY DIVISION 26.
7 PROVIDE DISCONNECT SWITCH (TOGGLE SWITCH ACCEPTABLE) FOR OVERHEAD DOORTO CUT POWER TO THE MOTOR (LOCATE SWITCH ON WALL ADJACENT TO OPEN/CLOSEBUTTON FOR DOOR).
8 PROVIDE CONNECTIONS TO BUILDING SIGNAGE. ASSUME CONNECTION FOR EACHINDIVIDUAL LETTER (SEE ARCHITECTURAL ELEVATIONS FOR QUANTITY OF LETTERS).
9 PROVIDE DUPLEX POWER OUTLET INSIDE CHIEF BOX NOTED ON SHEET E107.
10 VERIFY LOCATION OF FLOOR BOX (TO BE USED FOR PRINTER) WITH ARCHITECT PRIORTO INSTALLATION.
1 FOR CIRCUIT HOMERUNS OVER 100', PROVIDE MINIMUM #10 AWG WIRING.
2 PROVIDE UNSWITCHED POWER TO ALL EM BALLASTS AND EXIT SIGNS.
SCALE: 3/32" = 1'-0"1POWER PLAN
N
0 6' 12' 24'
-
J
ST
ST2 2
E F G H
I.T. ROOM
201
MECH. /
ELEC.
202
PARTS
STORAGE
200
1
2
L5-20RQUAD
L5-15RL5-20R
"1RB"
"1HB"
"1LB"
"MH"
1LB-531LB-52
1LB-55
1LB-561LB-57
1LB-541LB-59
"ML3"
UH-1ML3-1
UH-1ML3-1
TO OUTDOOR UNIT
UH-3ML3-15,17
324 S
. S
tate
St., S
uite 4
00
Salt L
ake C
ity, U
T 84111
800-6
78-7
077
801-3
28-5
151
fax: 801-3
28-5
155
ww
w.s
pectr
um
-engin
eers
.com
Ken G
arf
fA
uto
mo
tive
Gro
up
CO
PY
RIG
HT
ED
DO
CU
ME
NT
TH
IS D
RA
WIN
G A
ND
TH
E B
IM/C
AD
FIL
E F
RO
M W
HIC
H IT
HA
S B
EE
N G
EN
ER
AT
ED
AR
E P
RO
VID
ED
AS
AN
IN
ST
RU
ME
NT
OF
SE
RV
ICE
FO
R T
HIS
PR
OJE
CT
. T
HE
SE
DO
CU
ME
NT
S A
RE
TH
E S
OL
E P
RO
PE
RT
Y G
OR
EE
AR
CH
ITE
CT
S. A
NY
US
E O
F T
HE
SE
DO
CU
ME
NT
S, D
AT
A A
ND
DE
SIG
NS
FO
R P
UR
PO
SE
S O
TH
ER
TH
AN
TH
OS
E A
SS
OC
IAT
ED
WIT
H T
HIS
PR
OJE
CT
WIT
HO
UT
TH
E E
XP
RE
SS
ED
, W
RIT
TE
N P
ER
MIS
SIO
N O
F F
RE
D G
OR
EE
AR
CH
ITE
CT
S IS
PR
OH
IBIT
ED
.
Revis
ion
His
tory
:
Pro
ject
No
: 150
3
Da
te:
Mark
:
t. 71
3-66
0-61
0247
10 B
ella
ire B
lvd.
#10
5B
ella
ire, T
exas
774
01
GO
RE
EARCHITECTS
50
1963-2013
YEARS
11
/03
/15
DD
SE
T
DATE: 11/11/2015
MEZZANINE
POWER PLAN
E-101
DO
WN
TO
WN
SA
LT
LA
KE
Jagu
ar
- L
an
d R
over
150 E
500 S
, S
AL
T L
AK
E C
ITY
, U
T 8
4111
A N
EW
AU
TO
MO
TIV
E F
AC
ILIT
Y D
ES
IGN
FO
R
SCALE: 3/32" = 1'-0"
MEZZANINE POWER PLAN1
GENERAL SHEET NOTES
SHEET KEYNOTES1 PROVIDE (2) 4" FIRE CAULKED SLEEVES (OR HILTI OR 3M SLEEVES THAT DO NOT
REQUIRE FIRE CAULKING BUT COMPRESS WHEN HEATED AROUND CABLE) TOACCESSIBLE CEILING BELOW.
2 PROVIDE 2" CONDUIT FROM CEILING OF THIS ROOM TO ROOF. PROVIDEWEATHERHEAD ON END OF CONDUIT AT ROOF. FLASH ALL PENETRATIONS AT ROOF.CONDUIT SHOULD PENETRATE INTO ROOM AT WEST SIDE OF ROOM (NOT ABOVERACKS).
1 FOR CIRCUIT HOMERUNS OVER 100', PROVIDE MINIMUM #10 AWG WIRING.
2 PROVIDE UNSWITCHED POWER TO ALL EM BALLASTS AND EXIT SIGNS.
N
0 6' 12' 24'
-
T
ST
C
C
E
E
F
F
G
G
H
H
2 2
4 4
3 3
1
EC-8PARTS-H-7,9,11
EC-8bPARTS-L-7
EF-8PARTS-H-1,3,5
W
PARTS-L-13
EC-4MH-43,45,47
EF-4MH-1,3,5EC-4B
ML2-33
EF-13MH-1,3,5
EF-5MH-1,3,5
1
EC-5MH-44,46,48 EC-5B
ML2-35
EF-6MH-2,4,6
1
EC-6MH-49,51,53 EC-6B
ML2-37
EF-14ML2-39
WW
W
1
EC-1MH-55,57,59 EC-1B
ML3-21
WMAU-1
MH-50,52,54EF-9
MH-26,28,30EF-1
MH-38,40,42EF-2
MH-31,33,35
1
EC-2MH-61,63,65 EC-2B
ML3-23
W
EF-3MH-32,34,36
EF-10MH-37,39,41
1
EC-3MH-62,64,66 EC-3B
ML3-20
W
MAU-2MH-67,69,71
EF-7MH-7,9,11
1
EC-7MH-56,58,60 EC-7B
ML3-24
W
RTU-6MH-8,10,12
W
RTU-1MH-13,15,17
W
RTU-2MH-14,16,18
RTU-5MH-19,21,23
W
RTU-3MH-20,22,24
RTU-4MH-25,27,29
EF-11ML3-22
EF-12ML3-19AC-1B
ML3-16,18
1LA-27
1LB-73
1LB-75
324 S
. S
tate
St., S
uite 4
00
Salt L
ake C
ity, U
T 84111
800-6
78-7
077
801-3
28-5
151
fax: 801-3
28-5
155
ww
w.s
pectr
um
-engin
eers
.com
Ken G
arf
fA
uto
mo
tive
Gro
up
CO
PY
RIG
HT
ED
DO
CU
ME
NT
TH
IS D
RA
WIN
G A
ND
TH
E B
IM/C
AD
FIL
E F
RO
M W
HIC
H IT
HA
S B
EE
N G
EN
ER
AT
ED
AR
E P
RO
VID
ED
AS
AN
IN
ST
RU
ME
NT
OF
SE
RV
ICE
FO
R T
HIS
PR
OJE
CT
. T
HE
SE
DO
CU
ME
NT
S A
RE
TH
E S
OL
E P
RO
PE
RT
Y G
OR
EE
AR
CH
ITE
CT
S. A
NY
US
E O
F T
HE
SE
DO
CU
ME
NT
S, D
AT
A A
ND
DE
SIG
NS
FO
R P
UR
PO
SE
S O
TH
ER
TH
AN
TH
OS
E A
SS
OC
IAT
ED
WIT
H T
HIS
PR
OJE
CT
WIT
HO
UT
TH
E E
XP
RE
SS
ED
, W
RIT
TE
N P
ER
MIS
SIO
N O
F F
RE
D G
OR
EE
AR
CH
ITE
CT
S IS
PR
OH
IBIT
ED
.
Revis
ion
His
tory
:
Pro
ject
No
: 150
3
Da
te:
Mark
:
t. 71
3-66
0-61
0247
10 B
ella
ire B
lvd.
#10
5B
ella
ire, T
exas
774
01
GO
RE
EARCHITECTS
50
1963-2013
YEARS
11
/03
/15
DD
SE
T
DATE: 11/11/2015
ROOF POWER
PLAN
E-102
DO
WN
TO
WN
SA
LT
LA
KE
Jagu
ar
- L
an
d R
over
150 E
500 S
, S
AL
T L
AK
E C
ITY
, U
T 8
4111
A N
EW
AU
TO
MO
TIV
E F
AC
ILIT
Y D
ES
IGN
FO
R
SCALE: 3/32" = 1'-0"1ROOF POWER PLAN
GENERAL SHEET NOTES
SHEET KEYNOTES1 SEE MECHANICAL SCHEMATIC FOR CONTROL/INTERCONNECT WIRING BY ELECTRICAL
CONTRACTOR. INTERCONNECT WIRING BETWEEN EVAPORATIVE COOLERS ANDEXHAUST FANS WILL HAVE CORRESPONDING NUMBERS (I.E. EC-4 AND EF-4).
1 FOR CIRCUIT HOMERUNS OVER 100', PROVIDE MINIMUM #10 AWG WIRING.
2 PROVIDE UNSWITCHED POWER TO ALL EM BALLASTS AND EXIT SIGNS.
N
0 6' 12' 24'
-
C
C
E
E
F
F
G
G
H
H
2 2
4 4
3 3
LAND
ROVER
SALES
105
JAGUAR
SALES
104
CONF. /
TRAINING
110
BREAK
ROOM
120
JANITOR
122
HOSPITALITY
114
RECEPTION
101
OIL WASTE
152
MEN
121
STORAGE
159
WOMEN
123
CUSTOMER
LOUNGE
102
STORAGE
109
STORAGE
108
OIL /
COMPRESSOR-1
156-1
RISER
153
YARD
EQUIPMENT
154
PRE-OWNED
MANAGER
118
SALES
MANAGER
117
SALES
MANAGER
116
SERVICE
MANAGER
126
WARRANTY
129
RETAIL
PARTS
128
LAND
ROVER
SHOWROOM
106
JAGUAR
SHOWROOM
103
INTERNET
119
RETAIL
DISPLAY
127
ELECTRICAL
157
OIL /
COMPRESSOR-2
156-2
CORRIDOR
148
WOMEN
148A
SERVICE
SHOP
151
TECH
PARTS
142
SPECIAL
TOOLS
143
PARTS
MANAGER
130
WASH
ROOM
146
LOCKER
145A
MEN
145
PARTS
STORAGE
147APARTS
RECIEVING
147C
BREAKROOM
149
CENTER
MGR.
113
F&I
112
F&I
111
NEW CAR
DELIVERY
107
USED TIRES
150
DETAIL
BAYS
158
COLOR /
TRIM
115
VESTIBULE
100
SERVICE
RECEPTION
125
SERVICE
ADVISORS
124
(B)
(B)
(B)
(B)
(A)
(A)
(A)
(A)
(A) (A)
(A) (A)
(B) (B)
(B)
(B) (B)
(B)
(B)
(B)
(B)
(B) (B)
(B)
(B)
(B)
(B)
(B)
(B)
(B)
(B)
(B)
(B)
(B)
(B)
(B)
(A)
(B)
(B)
(B)
(B)
(B)
(B)
(B)
(B)
(B)
(B)
(B)
(B)
(B)
(A)
(A)
(A)
(A)
(B)
(B)
(B)
(C)(C)(C)(C)
(I)
(I)
(I)
(I)
(I)
(I) (I)
(I)
(I)
(I)
(I)
(I)
(I)
(I)
(I)
(I)
(I)
(C)
(C)
(C)
(C)
(H)
(H)
(H)
(H)
(D) (D) (D)
(D) (D) (D) (D)
(D)
(D)(D)(D)
(D)(D)
(E)
(E)
(E)
(E)
(E)
(E)
(E)
(E) (E)
(E)
(E)
(E)
(E)
(E)
(E)
(E)
(E)
(E)
(J)
(J)
(J)
(C)
(J)
(J)
(J)
(J)
(J)
(B)
(B)
(B) (B)
(J) (J) (J) (J)
(J) (J) (J) (J)
(J)
(J)
(B)
(B)
(B)
(B)
(B)
(B) (B)(B)
(J)
(J)
(J)
(J)
(J)
(J)
(J)
(J)
(J)(J)(J)(J)
(H) (H) (H)
(O)
(O)
(O) (O)
(O) (O) (O)
(O)(O) (O)
(O)
(K)
(K)
(K)
(K)
(K)
(K)
(K)
(K)
(K)
(K)
(K)
(K)
(K)
(K)(K)
(K)
(K)
(K)
(K)
(K)
(K)
(K)
(K)
(K)
(K)
(K)
(K)
(K)
(K)
(K)
(K)
(K)
(K)
(K)
(K)
(K)
(K)
(K)
(K)
(K)
(K)
(K)
(K)
(K)
(K)
(K)
(K)
(K)
(K)
(K)
(K)
(K)
(K)
(K)
(K)
(K)
(K)
(K)
(K)
(K)
(K)
(K)
(K)
(K)
(B)
(B)
(O)(O)(O)
(O)
(O)
(O)
(O)
(O)
(O)
(O)
(O)
(O)
(O)
(O)
(O)
(O)
(O)
(O)
(O)
(O)
(O)
(O)
(O)
(O)(O)
(N)(N)
(N)
(N)
(N)
(N)
(N)
(N)
(N)(N)
(N)
(N)
(N)
(N)
(N)
(N)
(L)
(L)
(L)
(L)
(L)
(L)
(L)
(L)
(L)
(L)
(L)
(L)
(L)
(L)
(L)
(L)
(L)
(L)
(L)
(L)
(M)(M) (M) (M)
(M)
(M)
(M)
(M)
(M)
(M)(M)(M)(M)(M)
(M)
(M)
(M) (M) (M) (M) (M)
(M)
(M)
EM
EM
EM
EM
EM
EM
EM
EM
EM
EM
EM
(D)
PARTS-H-2
"PARTS-L"
"PARTS-H"
EM
EM
PARTS-H-4
1HB-1
1RB-1
1HB-2
1RBEM
EM
EM
EM
EM EM EM
EM EM
EM
EM
EM
EM EM EM EM EM
EM EM EM
(M)
(M)
(P) (P) (P) (P) (P) (P) (P) (P) (P)
PARTS-H-6
1HA-3
"1HA"
"1LA"
"ML1""ML2"
"1RA"
1RB
EM
EM
EM
EM
EM
EM
EM
EM
EM
EM
EM
EM
EM
EM
EM
EM
EM
EM
EM
EM
EM
EM
EM
EM
EM
EM
EM
EM
EM
EM
3
3
EM
EM
EM
EM
(D)
(D)
(D)
(D)
(D)
(D)(D)
(D)
(D)
(M)
WS
WS
a a
ab
b
b b
bb
LV
(J)
LV
LV
1RA-11RA-21RA-31RA-4
1RA-5
1RA-6
1RA-7
1RA-8
1RA-9
1RA-10
1RA-11
1RA-12
1RA-13
1RA-14
1RB-2
WS
EM
EM
EM
EM
EM
1RB-4
1RB-5
1RB-6
1RB-7
1RB-8
4
(P) (P)
WS
WS
324 S
. S
tate
St., S
uite 4
00
Salt L
ake C
ity, U
T 84111
800-6
78-7
077
801-3
28-5
151
fax: 801-3
28-5
155
ww
w.s
pectr
um
-engin
eers
.com
Ken G
arf
fA
uto
mo
tive
Gro
up
CO
PY
RIG
HT
ED
DO
CU
ME
NT
TH
IS D
RA
WIN
G A
ND
TH
E B
IM/C
AD
FIL
E F
RO
M W
HIC
H IT
HA
S B
EE
N G
EN
ER
AT
ED
AR
E P
RO
VID
ED
AS
AN
IN
ST
RU
ME
NT
OF
SE
RV
ICE
FO
R T
HIS
PR
OJE
CT
. T
HE
SE
DO
CU
ME
NT
S A
RE
TH
E S
OL
E P
RO
PE
RT
Y G
OR
EE
AR
CH
ITE
CT
S. A
NY
US
E O
F T
HE
SE
DO
CU
ME
NT
S, D
AT
A A
ND
DE
SIG
NS
FO
R P
UR
PO
SE
S O
TH
ER
TH
AN
TH
OS
E A
SS
OC
IAT
ED
WIT
H T
HIS
PR
OJE
CT
WIT
HO
UT
TH
E E
XP
RE
SS
ED
, W
RIT
TE
N P
ER
MIS
SIO
N O
F F
RE
D G
OR
EE
AR
CH
ITE
CT
S IS
PR
OH
IBIT
ED
.
Revis
ion
His
tory
:
Pro
ject
No
: 150
3
Da
te:
Mark
:
t. 71
3-66
0-61
0247
10 B
ella
ire B
lvd.
#10
5B
ella
ire, T
exas
774
01
GO
RE
EARCHITECTS
50
1963-2013
YEARS
11
/03
/15
DD
SE
T
DATE: 11/11/2015
LIGHTING PLAN
E-103
DO
WN
TO
WN
SA
LT
LA
KE
Jagu
ar
- L
an
d R
over
150 E
500 S
, S
AL
T L
AK
E C
ITY
, U
T 8
4111
A N
EW
AU
TO
MO
TIV
E F
AC
ILIT
Y D
ES
IGN
FO
R
SCALE: 3/32" = 1'-0"1LIGHTING PLAN
GENERAL SHEET NOTES
SHEET KEYNOTES
1 FOR CIRCUIT HOMERUNS OVER 100', PROVIDE MINIMUM #10 AWG WIRING.
2 PROVIDE UNSWITCHED POWER TO ALL EM BALLASTS AND EXIT SIGNS.
N
0 6' 12' 24'
-
B C E FD
E
E
F
F
G
G
H
H
I.T. ROOM
201
MECH. /
ELEC.
202
"1RB"
"1HB"
"ML3"
"1LB"
324 S
. S
tate
St., S
uite 4
00
Salt L
ake C
ity, U
T 84111
800-6
78-7
077
801-3
28-5
151
fax: 801-3
28-5
155
ww
w.s
pectr
um
-engin
eers
.com
Ken G
arf
fA
uto
mo
tive
Gro
up
CO
PY
RIG
HT
ED
DO
CU
ME
NT
TH
IS D
RA
WIN
G A
ND
TH
E B
IM/C
AD
FIL
E F
RO
M W
HIC
H IT
HA
S B
EE
N G
EN
ER
AT
ED
AR
E P
RO
VID
ED
AS
AN
IN
ST
RU
ME
NT
OF
SE
RV
ICE
FO
R T
HIS
PR
OJE
CT
. T
HE
SE
DO
CU
ME
NT
S A
RE
TH
E S
OL
E P
RO
PE
RT
Y G
OR
EE
AR
CH
ITE
CT
S. A
NY
US
E O
F T
HE
SE
DO
CU
ME
NT
S, D
AT
A A
ND
DE
SIG
NS
FO
R P
UR
PO
SE
S O
TH
ER
TH
AN
TH
OS
E A
SS
OC
IAT
ED
WIT
H T
HIS
PR
OJE
CT
WIT
HO
UT
TH
E E
XP
RE
SS
ED
, W
RIT
TE
N P
ER
MIS
SIO
N O
F F
RE
D G
OR
EE
AR
CH
ITE
CT
S IS
PR
OH
IBIT
ED
.
Revis
ion
His
tory
:
Pro
ject
No
: 150
3
Da
te:
Mark
:
t. 71
3-66
0-61
0247
10 B
ella
ire B
lvd.
#10
5B
ella
ire, T
exas
774
01
GO
RE
EARCHITECTS
50
1963-2013
YEARS
11
/03
/15
DD
SE
T
DATE: 11/11/2015
MEZZANINE
LIGHITNG PLAN
E-104
DO
WN
TO
WN
SA
LT
LA
KE
Jagu
ar
- L
an
d R
over
150 E
500 S
, S
AL
T L
AK
E C
ITY
, U
T 8
4111
A N
EW
AU
TO
MO
TIV
E F
AC
ILIT
Y D
ES
IGN
FO
R
GENERAL SHEET NOTES
SHEET KEYNOTES
1 FOR CIRCUIT HOMERUNS OVER 100', PROVIDE MINIMUM #10 AWG WIRING.
2 PROVIDE UNSWITCHED POWER TO ALL EM BALLASTS AND EXIT SIGNS.
N
0 6' 12' 24'SCALE: 3/32" = 1'-0"
MEZZANINE LIGHTING PLAN1
-
A B C E FD
C
C
E
E
F
F
G
G
H
H
STORAGE
159 DETAILBAYS
158
324 S
. S
tate
St., S
uite 4
00
Salt L
ake C
ity, U
T 84111
800-6
78-7
077
801-3
28-5
151
fax: 801-3
28-5
155
ww
w.s
pectr
um
-engin
eers
.com
Ken G
arf
fA
uto
mo
tive
Gro
up
CO
PY
RIG
HT
ED
DO
CU
ME
NT
TH
IS D
RA
WIN
G A
ND
TH
E B
IM/C
AD
FIL
E F
RO
M W
HIC
H IT
HA
S B
EE
N G
EN
ER
AT
ED
AR
E P
RO
VID
ED
AS
AN
IN
ST
RU
ME
NT
OF
SE
RV
ICE
FO
R T
HIS
PR
OJE
CT
. T
HE
SE
DO
CU
ME
NT
S A
RE
TH
E S
OL
E P
RO
PE
RT
Y G
OR
EE
AR
CH
ITE
CT
S. A
NY
US
E O
F T
HE
SE
DO
CU
ME
NT
S, D
AT
A A
ND
DE
SIG
NS
FO
R P
UR
PO
SE
S O
TH
ER
TH
AN
TH
OS
E A
SS
OC
IAT
ED
WIT
H T
HIS
PR
OJE
CT
WIT
HO
UT
TH
E E
XP
RE
SS
ED
, W
RIT
TE
N P
ER
MIS
SIO
N O
F F
RE
D G
OR
EE
AR
CH
ITE
CT
S IS
PR
OH
IBIT
ED
.
Revis
ion
His
tory
:
Pro
ject
No
: 150
3
Da
te:
Mark
:
t. 71
3-66
0-61
0247
10 B
ella
ire B
lvd.
#10
5B
ella
ire, T
exas
774
01
GO
RE
EARCHITECTS
50
1963-2013
YEARS
11
/03
/15
DD
SE
T
DATE: 11/11/2015
FIRE ALARM PLAN
E-105
DO
WN
TO
WN
SA
LT
LA
KE
Jagu
ar
- L
an
d R
over
150 E
500 S
, S
AL
T L
AK
E C
ITY
, U
T 8
4111
A N
EW
AU
TO
MO
TIV
E F
AC
ILIT
Y D
ES
IGN
FO
R
GENERAL SHEET NOTES
SHEET KEYNOTES
1 FOR CIRCUIT HOMERUNS OVER 100', PROVIDE MINIMUM #10 AWG WIRING.
2 PROVIDE UNSWITCHED POWER TO ALL EM BALLASTS AND EXIT SIGNS.
N
0 6' 12' 24'SCALE: 3/32" = 1'-0"1
FIRE ALARM PLAN
-
B C E FD
E
E
F
F
G
G
H
H
I.T. ROOM
201
MECH. /
ELEC.
202
324 S
. S
tate
St., S
uite 4
00
Salt L
ake C
ity, U
T 84111
800-6
78-7
077
801-3
28-5
151
fax: 801-3
28-5
155
ww
w.s
pectr
um
-engin
eers
.com
Ken G
arf
fA
uto
mo
tive
Gro
up
CO
PY
RIG
HT
ED
DO
CU
ME
NT
TH
IS D
RA
WIN
G A
ND
TH
E B
IM/C
AD
FIL
E F
RO
M W
HIC
H IT
HA
S B
EE
N G
EN
ER
AT
ED
AR
E P
RO
VID
ED
AS
AN
IN
ST
RU
ME
NT
OF
SE
RV
ICE
FO
R T
HIS
PR
OJE
CT
. T
HE
SE
DO
CU
ME
NT
S A
RE
TH
E S
OL
E P
RO
PE
RT
Y G
OR
EE
AR
CH
ITE
CT
S. A
NY
US
E O
F T
HE
SE
DO
CU
ME
NT
S, D
AT
A A
ND
DE
SIG
NS
FO
R P
UR
PO
SE
S O
TH
ER
TH
AN
TH
OS
E A
SS
OC
IAT
ED
WIT
H T
HIS
PR
OJE
CT
WIT
HO
UT
TH
E E
XP
RE
SS
ED
, W
RIT
TE
N P
ER
MIS
SIO
N O
F F
RE
D G
OR
EE
AR
CH
ITE
CT
S IS
PR
OH
IBIT
ED
.
Revis
ion
His
tory
:
Pro
ject
No
: 150
3
Da
te:
Mark
:
t. 71
3-66
0-61
0247
10 B
ella
ire B
lvd.
#10
5B
ella
ire, T
exas
774
01
GO
RE
EARCHITECTS
50
1963-2013
YEARS
11
/03
/15
DD
SE
T
DATE: 11/11/2015
MEZZANINE FIRE
ALARM PLAN
E-106
DO
WN
TO
WN
SA
LT
LA
KE
Jagu
ar
- L
an
d R
over
150 E
500 S
, S
AL
T L
AK
E C
ITY
, U
T 8
4111
A N
EW
AU
TO
MO
TIV
E F
AC
ILIT
Y D
ES
IGN
FO
R
SCALE: 3/32" = 1'-0"
MEZZANINE FIRE ALARM PLAN1
GENERAL SHEET NOTES
SHEET KEYNOTES
1 FOR CIRCUIT HOMERUNS OVER 100', PROVIDE MINIMUM #10 AWG WIRING.
2 PROVIDE UNSWITCHED POWER TO ALL EM BALLASTS AND EXIT SIGNS.
N
0 6' 12' 24'
-
J J J J J J J
J J J J J
JJ
J
J
J J J
J
J
J
J
JJ J J
J J
J
J J
J
J
J
J
J
JJ
JJ
J
A B C E F
5
1
3
D
4
2
C
C
E
E
F
F
G
G
H
H
2 2
4 4
3 3
LAND
ROVER
SALES
105
JAGUAR
SALES
104
CONF. /
TRAINING
110
BREAK
ROOM
120
JANITOR
122
HOSPITALITY
114
RECEPTION
101
OIL WASTE
152
MEN
121
STORAGE
159
WOMEN
123
CUSTOMER
LOUNGE
102
STORAGE
109
STORAGE
108
OIL /
COMPRESSOR-1
156-1
RISER
153
YARD
EQUIPMENT
154
PRE-OWNED
MANAGER
118
SALES
MANAGER
117
SALES
MANAGER
116
SERVICE
MANAGER
126
WARRANTY
129
RETAIL
PARTS
128
LAND
ROVER
SHOWROOM
106
JAGUAR
SHOWROOM
103
INTERNET
119
RETAIL
DISPLAY
127
ELECTRICAL
157
OIL /
COMPRESSOR-2
156-2
CORRIDOR
148
WOMEN
148A
SERVICE
SHOP
151
TECH
PARTS
142
SPECIAL
TOOLS
143
PARTS
MANAGER
130
WASH
ROOM
146
LOCKER
145A
MEN
145
PARTS
STORAGE
147APARTS
RECIEVING
147C
BREAKROOM
149
CENTER
MGR.
113
F&I
112
F&I
111
NEW CAR
DELIVERY
107
USED TIRES
150
DETAIL
BAYS
158
COLOR /
TRIM
115
VESTIBULE
100
SERVICE
RECEPTION
125
SERVICE
ADVISORS
124
A
A A A
A
A A AA
A A AA
A A AA
A A AA
A A AA
A A
AAA
A AAAA
AAAA
AAAA
AAAA
WAP
WAP
WAP
WAP
FB2 FB2 FB2 FB2
FB2 FB
2
FB
2
FB
2
FB2 FB2
FB2
FB2 FB2 FB2 FB2
FB2F
B2
FB
2
FB
2
FB
2F
B2
FB
2F
B2
FB2
2AVC C 2AV
1 1
FB
2
2AV
1
2
2AV2AV2AV
1 1 1
2 2 22"C. 2"C. 2"C.
2AV
2
21
2"C.
2"C.
2AV
1
2
4
2AV
2
2"C.
2
1
2AV
2
1
2AV
2
1
2"C. 2"C. 2"C.
2"C.
2AV
1
3
1
3
324 S
. S
tate
St., S
uite 4
00
Salt L
ake C
ity, U
T 84111
800-6
78-7
077
801-3
28-5
151
fax: 801-3
28-5
155
ww
w.s
pectr
um
-engin
eers
.com
Ken G
arf
fA
uto
mo
tive
Gro
up
CO
PY
RIG
HT
ED
DO
CU
ME
NT
TH
IS D
RA
WIN
G A
ND
TH
E B
IM/C
AD
FIL
E F
RO
M W
HIC
H IT
HA
S B
EE
N G
EN
ER
AT
ED
AR
E P
RO
VID
ED
AS
AN
IN
ST
RU
ME
NT
OF
SE
RV
ICE
FO
R T
HIS
PR
OJE
CT
. T
HE
SE
DO
CU
ME
NT
S A
RE
TH
E S
OL
E P
RO
PE
RT
Y G
OR
EE
AR
CH
ITE
CT
S. A
NY
US
E O
F T
HE
SE
DO
CU
ME
NT
S, D
AT
A A
ND
DE
SIG
NS
FO
R P
UR
PO
SE
S O
TH
ER
TH
AN
TH
OS
E A
SS
OC
IAT
ED
WIT
H T
HIS
PR
OJE
CT
WIT
HO
UT
TH
E E
XP
RE
SS
ED
, W
RIT
TE
N P
ER
MIS
SIO
N O
F F
RE
D G
OR
EE
AR
CH
ITE
CT
S IS
PR
OH
IBIT
ED
.
Revis
ion
His
tory
:
Pro
ject
No
: 150
3
Da
te:
Mark
:
t. 71
3-66
0-61
0247
10 B
ella
ire B
lvd.
#10
5B
ella
ire, T
exas
774
01
GO
RE
EARCHITECTS
50
1963-2013
YEARS
11
/03
/15
DD
SE
T
DATE: 11/11/2015
TELECOM PLAN
E-107
DO
WN
TO
WN
SA
LT
LA
KE
Jagu
ar
- L
an
d R
over
150 E
500 S
, S
AL
T L
AK
E C
ITY
, U
T 8
4111
A N
EW
AU
TO
MO
TIV
E F
AC
ILIT
Y D
ES
IGN
FO
R
GENERAL SHEET NOTES
SHEET KEYNOTES1 COORDINATE EXACT MOUNTING HEIGHT WITH AV INSTALLER.
2 PROVIDE CHIEF PAC 526 BACK BOX.
3 PULL 2 CAT 6 CABLES BACK TO THE CHIEF PACK 526 BOX IN CENTER MANAGER'SOFFICE. LEAVE 10'-0" COIL OF CABLE ON BOTH ENDS.
1 FOR CIRCUIT HOMERUNS OVER 100', PROVIDE MINIMUM #10 AWG WIRING.
2 PROVIDE UNSWITCHED POWER TO ALL EM BALLASTS AND EXIT SIGNS.
N
0 6' 12' 24'SCALE: 3/32" = 1'-0"1
TELECOMMUNICATIONS PLAN
-
J
B C E FDE F G H
I.T. ROOM
201 MECH. /
ELEC.
202
PARTS
STORAGE
200
E-401
2
3' - 0"
L5-20RQUAD
L5-15RL5-20R
1
2
324 S
. S
tate
St., S
uite 4
00
Salt L
ake C
ity, U
T 84111
800-6
78-7
077
801-3
28-5
151
fax: 801-3
28-5
155
ww
w.s
pectr
um
-engin
eers
.com
Ken G
arf
fA
uto
mo
tive
Gro
up
CO
PY
RIG
HT
ED
DO
CU
ME
NT
TH
IS D
RA
WIN
G A
ND
TH
E B
IM/C
AD
FIL
E F
RO
M W
HIC
H IT
HA
S B
EE
N G
EN
ER
AT
ED
AR
E P
RO
VID
ED
AS
AN
IN
ST
RU
ME
NT
OF
SE
RV
ICE
FO
R T
HIS
PR
OJE
CT
. T
HE
SE
DO
CU
ME
NT
S A
RE
TH
E S
OL
E P
RO
PE
RT
Y G
OR
EE
AR
CH
ITE
CT
S. A
NY
US
E O
F T
HE
SE
DO
CU
ME
NT
S, D
AT
A A
ND
DE
SIG
NS
FO
R P
UR
PO
SE
S O
TH
ER
TH
AN
TH
OS
E A
SS
OC
IAT
ED
WIT
H T
HIS
PR
OJE
CT
WIT
HO
UT
TH
E E
XP
RE
SS
ED
, W
RIT
TE
N P
ER
MIS
SIO
N O
F F
RE
D G
OR
EE
AR
CH
ITE
CT
S IS
PR
OH
IBIT
ED
.
Revis
ion
His
tory
:
Pro
ject
No
: 150
3
Da
te:
Mark
:
t. 71
3-66
0-61
0247
10 B
ella
ire B
lvd.
#10
5B
ella
ire, T
exas
774
01
GO
RE
EARCHITECTS
50
1963-2013
YEARS
11
/03
/15
DD
SE
T
DATE: 11/11/2015
MEZZANINE
TELECOM PLAN
E-108
DO
WN
TO
WN
SA
LT
LA
KE
Jagu
ar
- L
an
d R
over
150 E
500 S
, S
AL
T L
AK
E C
ITY
, U
T 8
4111
A N
EW
AU
TO
MO
TIV
E F
AC
ILIT
Y D
ES
IGN
FO
R
GENERAL SHEET NOTES
SHEET KEYNOTES1 PROVIDE 2" CONDUIT FROM CEILING OF THIS ROOM TO ROOF. PROVIDE
WEATHERHEAD ON END OF CONDUIT AT ROOF. FLASH ALL PENETRATIONS AT ROOF.CONDUIT SHOULD PENETRATE INTO ROOM AT WEST SIDE OF ROOM (NOT ABOVERACKS).
2 PROVIDE (2) 4" FIRE CAULKED SLEEVES (OR HILTI OR 3M SLEEVES THAT DO NOTREQUIRE FIRE CAULKING BUT COMPRESS WHEN HEATED AROUND CABLE) TOACCESSIBLE CEILING BELOW.
1 FOR CIRCUIT HOMERUNS OVER 100', PROVIDE MINIMUM #10 AWG WIRING.
2 PROVIDE UNSWITCHED POWER TO ALL EM BALLASTS AND EXIT SIGNS.
N
0 6' 12' 24'SCALE: 3/32" = 1'-0"1
MEZZANINE TELECOMMUICATIONS PLAN
-
I.T. ROOM
201
4' -
4"
4' -
4"
8' - 1 3/4" 10' - 4 3/8"
324 S
. S
tate
St., S
uite 4
00
Salt L
ake C
ity, U
T 84111
800-6
78-7
077
801-3
28-5
151
fax: 801-3
28-5
155
ww
w.s
pectr
um
-engin
eers
.com
Ken G
arf
fA
uto
mo
tive
Gro
up
CO
PY
RIG
HT
ED
DO
CU
ME
NT
TH
IS D
RA
WIN
G A
ND
TH
E B
IM/C
AD
FIL
E F
RO
M W
HIC
H IT
HA
S B
EE
N G
EN
ER
AT
ED
AR
E P
RO
VID
ED
AS
AN
IN
ST
RU
ME
NT
OF
SE
RV
ICE
FO
R T
HIS
PR
OJE
CT
. T
HE
SE
DO
CU
ME
NT
S A
RE
TH
E S
OL
E P
RO
PE
RT
Y G
OR
EE
AR
CH
ITE
CT
S. A
NY
US
E O
F T
HE
SE
DO
CU
ME
NT
S, D
AT
A A
ND
DE
SIG
NS
FO
R P
UR
PO
SE
S O
TH
ER
TH
AN
TH
OS
E A
SS
OC
IAT
ED
WIT
H T
HIS
PR
OJE
CT
WIT
HO
UT
TH
E E
XP
RE
SS
ED
, W
RIT
TE
N P
ER
MIS
SIO
N O
F F
RE
D G
OR
EE
AR
CH
ITE
CT
S IS
PR
OH
IBIT
ED
.
Revis
ion
His
tory
:
Pro
ject
No
: 150
3
Da
te:
Mark
:
t. 71
3-66
0-61
0247
10 B
ella
ire B
lvd.
#10
5B
ella
ire, T
exas
774
01
GO
RE
EARCHITECTS
50
1963-2013
YEARS
11
/03
/15
DD
SE
T
DATE: 11/11/2015
ENLARGED
TELECOM PLANS
E-401
DO
WN
TO
WN
SA
LT
LA
KE
Jagu
ar
- L
an
d R
over
150 E
500 S
, S
AL
T L
AK
E C
ITY
, U
T 8
4111
A N
EW
AU
TO
MO
TIV
E F
AC
ILIT
Y D
ES
IGN
FO
R
SCALE:1ENLARGED IT 201 TELECOMMUNICATIONS PLAN
SCALE: 1/4" = 1'-0"2ENLARGED IT 201 TELECOMMUICATIONS PLAN
-
SPD
M
GROUNDPER NEC
T1300kVA480-208Y/120V3, 4WDELTA/ WYE, K-1 RATED
#4/0 CU
LSI
1200/ 3
225/3
30
225/3
"1HA"
225/3
30
225/3
"1HB"
225/3
30
225/3
"MH"
100/3
20
100/3
"PARTS-H"
225/3
30
SECT2
225/3
"1LA" "1LA"
225/3
225/3
30
SECT2
225/3
"1LB" "1LB"
225/3
400/3
36
SECT2
400/3
"ML1" "ML1"
400/3
400/3
36
SECT2
400/3
"ML2" "ML2"
400/3
225/3
30
SECT2
225/3
"ML3" "ML3"
225/3
100/3
20
100/3
"PARTS-L"
CALCULATIONS ARE BASED ON THE FOLLOWING ASSUMPTIONS:
NOTES:
CONTRACTOR SHALL SUBMIT VARIATIONS FROMASSUMPTIONS PRIOR TO ORDERING EQUIPMENT.
SERVICE EQUIPMENT SHALL BE LEGIBLY MARKED INTHE FIELD WITH THE MAXIMUM AVAILABLE FAULTCURRENT. VERIFY OR RE-CALCULATE THEAVAILABLE FAULT CURRENT AT THE SERVICE WHEREMODIFICATIONS TO THE ELECTRICAL INSTALLATIONWILL OCCUR.
1.
2.
PROVIDE PERMANENT LABEL ON "MAIN SWITCHBOARD" STATING:
"MAXIMUM CALCULATED AIC - XXXXXA, 1980-07- 11"
- INFINITE PRIMARY- UTILITY TRANSFORMNER SIZE XXXkVA- TRANSFORMER IMPEDANCE OF XX%- SUPPLY FEEDER LENGTH OF XX'
NOTE: THIS LABEL IS REQUIRED TO GO ON THE
ONE-LINE DIAGRAM ABOVE THE SWITCHBOARD
PER NEC. DELETE THE PARAMETER "TYPE"
VALUE TO HIDE THIS NOTE. DO NOT PRINT THIS
EXISTING METIRING SWITCHBOARD "CTE"480/277V, 3, 4W2500 A MLO, 65000AICGROUND BUS100% NEUTRAL
DISTRIBUTION PANELBOARD "MS"480/277V, 3, 4W1200 A, 42000AICGROUND BUS100% NEUTRAL
GFP
1200/3LSIG
GROUND BUS
WATERSTEELUFER GROUNDROD
#3/0 CU
#6 CU
52
600/3
41
DISTRIBUTION PANELBOARD "LDP"208/120V, 3, 4W1200 A MCB, 35000AICGROUND BUS100% NEUTRAL
52SE
(EXISTING)
DO NOT BOND NEUTRALTO GROUND BUS
(2) 225/3 SPACES
(2) 225/3 SPACES
"CTE" INSTALLED UNDER PREVIOUS CONTRACT.
324 S
. S
tate
St., S
uite 4
00
Salt L
ake C
ity, U
T 84111
800-6
78-7
077
801-3
28-5
151
fax: 801-3
28-5
155
ww
w.s
pectr
um
-engin
eers
.com
Ken G
arf
fA
uto
mo
tive
Gro
up
CO
PY
RIG
HT
ED
DO
CU
ME
NT
TH
IS D
RA
WIN
G A
ND
TH
E B
IM/C
AD
FIL
E F
RO
M W
HIC
H IT
HA
S B
EE
N G
EN
ER
AT
ED
AR
E P
RO
VID
ED
AS
AN
IN
ST
RU
ME
NT
OF
SE
RV
ICE
FO
R T
HIS
PR
OJE
CT
. T
HE
SE
DO
CU
ME
NT
S A
RE
TH
E S
OL
E P
RO
PE
RT
Y G
OR
EE
AR
CH
ITE
CT
S. A
NY
US
E O
F T
HE
SE
DO
CU
ME
NT
S, D
AT
A A
ND
DE
SIG
NS
FO
R P
UR
PO
SE
S O
TH
ER
TH
AN
TH
OS
E A
SS
OC
IAT
ED
WIT
H T
HIS
PR
OJE
CT
WIT
HO
UT
TH
E E
XP
RE
SS
ED
, W
RIT
TE
N P
ER
MIS
SIO
N O
F F
RE
D G
OR
EE
AR
CH
ITE
CT
S IS
PR
OH
IBIT
ED
.
Revis
ion
His
tory
:
Pro
ject
No
: 150
3
Da
te:
Mark
:
t. 71
3-66
0-61
0247
10 B
ella
ire B
lvd.
#10
5B
ella
ire, T
exas
774
01
GO
RE
EARCHITECTS
50
1963-2013
YEARS
11
/03
/15
DD
SE
T
DATE: 11/11/2015
ONE-LINE
DIAGRAM
E-601
DO
WN
TO
WN
SA
LT
LA
KE
Jagu
ar
- L
an
d R
over
150 E
500 S
, S
AL
T L
AK
E C
ITY
, U
T 8
4111
A N
EW
AU
TO
MO
TIV
E F
AC
ILIT
Y D
ES
IGN
FO
R
GENERAL SHEET NOTES1 PROVIDE NEMA 3R ENCLOSURES FOR EQUIPMENT LOCATED OUTDOORS. REFER TO
PLANS FOR EQUIPMENT LOCATIONS.
2 REFER TO PLANS FOR CONSTRAINTS ON PHYSICAL DIMENSIONS AND CLEARANCEREQUIREMENTS OF EQUIPMENT. PROVIDE EQUIPMENT DIMENSIONS THAT FALLWITHIN THE CONSTRAINTS OF EACH SPECIFIC LOCATION.
3 ALL EQUIPMENT SHALL BE CONSTRUCTED AND BRACED FOR THE SEISMICCONDITIONS OF THE PROJECT. REFER TO ELECTRICAL SPECIFICATIONS FORREQUIREMENTS.
4 PROVIDE PERFORMANCE TESTING FOR GROUND-FAULT PROTECTION SYSTEMS ONSITE WITH A WRITTEN RECORD OF THIS TEST SUBMITTED TO THE AUTHORITY HAVINGJURISDICTION PER 2011 NEC 230.95(C).
6 RACEWAY ONLY. CONDUCTORS PROVIDED BY UTILITY.
7 ALUMINUM CONDUCTORS NOT TO BE USED FOR CONNECTION TO MOTORS ORMOTOR DRIVEN EQUIPMENT.
1 CONDUCTORS SHOWN ARE SHOWN FOR EACH CONDUIT WITH MODIFICATIONSAS NOTED IN NOTE 5. ALL CONDUCTORS SHOWN ARE THWN UNLESSOTHERWISE NOTED.
2 PROVIDE EQUIPMENT GROUND CONDUCTORS PER TABLE 250-122 WHENCIRCUIT BREAKERS ARE SIZED GREATER THAN AMPERE RATING SHOWN INTABLE.
3 PROVIDE #10 NEUTRALS FOR MULTIWIRE BRANCH CIRCUITS SERVINGCOMPUTERS.
4 GROUND (G) CONDUCTOR MAY BE DELETED ON SERVICE ENTRANCECONDUCTORS.
5 SYMBOL SUBSCRIPTS:
**IG
(E.G.)* SUBSCRIPT (NOTE 5)
SCHEDULE NUMBER
5
ALUMINUM CONDUCTORAND CONDUIT SCHEDULE
SYM AMPCONDUIT
SIZE
CONDUCTOR (NOTE 1)
IG SE NOTESQTY SIZE G
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21 130 2 3 2/0 4 1/0 4 2,7
22 130 2 4 2/0 4 1/0 4 2,7
23 150 2 3 3/0 4 1/0 4 2,7
24 150 2 4 3/0 4 1/0 4 2,7
25 175 2 3 4/0 4 1/0 2 2,7
26 175 2.50 4 4/0 4 1/0 2 2,7
27 200 2.50 3 250 4 1/0 2 2,7
28 200 3 4 250 4 1/0 2 2,7
29 230 2.50 3 300 2 1/0 1/0 2,7
30 230 3 4 300 2 1/0 1/0 2,7
31 250 3 3 350 2 2/0 1/0 2,7
32 250 3 4 350 2 2/0 1/0 2,7
33 310 3 3 500 1 3/0 1/0 2,7
34 310 4 4 500 1 3/0 1/0 2,7
35 380 2 EA 2.50 3 250 1 4/0 3/0 2,7
36 380 2 EA 3 4 250 1 4/0 3/0 2,7
37 400 2 EA 2.50 3 250 1/0 4/0 3/0 2,7
38 400 2 EA 2.50 4 250 1/0 4/0 3/0 2,7
39 500 2 EA 3 3 350 1/0 300 3/0 2,4,7
40 500 2 EA 3 4 350 1/0 300 3/0 2,4,7
41 620 2 EA 3 3 500 3/0 300 3/0 2,4,7
42 620 2 EA 4 4 500 3/0 300 3/0 2,4,7
43 750 3 EA 3 3 350 3/0 300 4/0 2,4,7
44 750 3 EA 4 4 350 3/0 300 4/0 2,4,7
45 810 3 EA 3 4 400 4/0 300 250 2,4,7
46 810 3 EA 4 4 400 4/0 300 250 2,4,7
47 1000 4 EA 3 3 350 4/0 300 250 4,7
48 1000 4 EA 3 4 350 4/0 300 250 4,7
49 1140 4 EA 4 3 500 250 300 250 4,7
50 1140 4 EA 4 4 500 250 300 250 4,7
51 1240 4 EA 4 3 500 350 300 250 4,7
52 1240 4 EA 4 4 500 350 300 250 4,7
53 1620 6 EA 4 4 400 400 350 250 4,7
54 2170 7 EA 4 4 500 400 500 250 4,7
55 2695 7 EA 4 4 750 600 750 750 4,7
56 3080 8 EA 4 4 750 600 750 750 4,7
57 4235 11 EA 4 4 750 800 750 750 4,7
58 - 5 EA 4 - - - - - 6
59 - 5 - - - - - 6
60 - 10 EA 4 - - - - - 6
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
"2N": INCLUDE TWO NEUTRAL CONDUCTORS, SIZED ASSCHEDULED FOR PHASED AND NEUTRAL CONDUCTORS.
"FG" FULL SIZE GROUND, SIZE EQUIPMENT GROUNDINGCONDUCTOR TO BE SAME SIZE AS THE PHASECONDUCTORS.
"HH": NEUTRAL CURRENTS EXIST DUE TO HIGH HARMONIC"NONLINEAR" LOADS. CURRENT CARRYING CONDUCTORSDERATED ACCORDINGLY.
"IG": INCLUDE IG (INSULATED/ISOLATED GROUND CONDUCTOR)SCHEDULED ALONG WITH THE GROUND OF EQUIPMENTGROUND CONDUCTOR.
"SE": SUBSTITUTE "SE" CONDUCTOR FOR "G" CONDUCTORSHOWN, WHICH IS SIZED FOR THE GROUNDING OF THESECONDARY OF THE SEPARATELY DERIVED SYSTEM.
SYM AMPHH
AMPSCONDUIT
SIZE
CONDUCTOR (NOTE 1)
IG/HH SE NOTESQTY SIZE G
1 20 - .75 2 12 12 12 8 2
2 20 - .75 3 12 12 12 8 2,3
3 20 24 .75 4 12 12 12 8 2,3
4 30 - .75 2 10 10 10 8 2
5 30 - .75 3 10 10 10 8 2
6 30 32 .75 4 10 10 10 8 2
7 40 - 1 2 8 10 8 6 2
8 40 - 1 3 8 10 8 6 2
9 40 44 1 4 8 10 8 6 2
10 55 - 1 2 6 10 8 4 2
11 55 - 1 3 6 10 8 4 2
12 55 60 1.25 4 6 10 8 4 2
13 70 - 1 2 4 8 4 2 2
14 70 - 1.25 3 4 8 4 2 2
15 70 76 1.25 4 4 8 4 2 2
16 85 - 1.25 2 3 8 3 2 2
17 85 - 1.25 3 3 8 3 2 2
18 85 92 1.25 4 3 8 3 2 2
19 95 - 1.25 3 2 8 2 2 2
20 95 104 1.50 4 2 8 2 2 2
21 130 - 1.50 3 1 6 2 2 2
22 130 116 1.50 4 1 6 2 2 2
23 150 - 2 3 1/0 6 2 1/0 2
24 150 136 2 4 1/0 6 2 1/0 2
25 175 - 2 3 2/0 6 2 2/0 2
26 175 156 2 4 2/0 6 2 2/0 2
27 200 - 2 3 3/0 6 2 2/0 2
28 200 180 2.50 4 3/0 6 2 2/0 2
29 230 - 2.50 3 4/0 4 2 2/0 2
30 230 208 2.50 4 4/0 4 2 2/0 2
31 255 - 2.50 3 250 4 1 2/0 2
32 255 232 2.50 4 250 4 1 2/0 2
33 310 - 3 3 350 3 1/0 3/0 2
34 310 280 3 4 350 3 1/0 3/0 2
35 380 - 3.50 3 500 3 3/0 3/0 2
36 380 344 4 4 500 3 3/0 3/0 2
37 400 - 2 EA 2 3 3/0 3 3/0 3/0 2
38 400 360 2 EA 2.50 4 3/0 3 3/0 3/0 2
39 510 - 2 EA 2.50 3 250 1 4/0 3/0 2
40 510 464 2 EA 3 4 250 1 4/0 3/0 2
41 620 - 2 EA 3 3 350 1/0 4/0 3/0 2,4
42 620 560 2 EA 3 4 350 1/0 4/0 3/0 2,4
43 760 - 2 EA 3.50 3 500 1/0 4/0 3/0 2,4
44 760 688 2 EA 4 4 500 1/0 4/0 3/0 2,4
45 855 - 3 EA 3 3 300 2/0 4/0 3/0 2,4
46 855 768 3 EA 3 4 300 2/0 4/0 3/0 2,4
47 1000 - 3 EA 3.50 3 400 2/0 4/0 3/0 4
48 1000 912 3 EA 3.50 4 400 2/0 4/0 3/0 4
49 1140 - 3 EA 4 3 500 3/0 4/0 3/0 4
50 1140 1032 3 EA 4 4 500 3/0 4/0 3/0 4
51 1240 - 4 EA 3 3 350 3/0 4/0 3/0 4
52 1240 1120 4 EA 3 4 350 3/0 4/0 3/0 4
53 1675 1520 5 EA 4 4 400 4/0 4/0 4/0 4
54 2010 1824 6 EA 4 4 400 250 250 250 4
55 2660 2408 7 EA 4 4 500 350 350 350 4
56 3040 2752 8 EA 4 4 500 500 500 500 4
57 4180 3784 11 EA 4 4 500 500 500 500 4
58 - - 5 EA 4 - - - - - 6
59 - - 5 - - - - - 6
60 - - 10 EA 4 - - - - - 6
**IG
(E.G.)*
COPPER CONDUCTOR ANDCONDUIT SCHEDULE
SUBSCRIPT (NOTE 5)
SCHEDULE NUMBER
5
6. RACEWAY ONLY. CONDUCTORS PROVIDED BY UTILITY.
1. CONDUCTORS SHOWN ARE SHOWN FOR EACH CONDUIT WITH MODIFICATIONSAS NOTED IN NOTE 5. ALL CONDUCTORS SHOWN ARE THWN UNLESSOTHERWISE NOTED.
2. PROVIDE EQUIPMENT GROUND CONDUCTORS PER TABLE 250-122 WHENCIRCUIT BREAKERS ARE SIZED GREATER THAN AMPERE RATING SHOWN INTABLE.
3. PROVIDE #10 NEUTRALS FOR MULTIWIRE BRANCH CIRCUITS SERVINGCOMPUTERS.
4. GROUND (G) CONDUCTOR MAY BE DELETED ON SERVICE ENTRANCECONDUCTORS.
5. SYMBOL SUBSCRIPTS:
"2N": INCLUDE TWO NEUTRAL CONDUCTORS, SIZED ASSCHEDULED FOR PHASED AND NEUTRAL CONDUCTORS.
"FG" FULL SIZE GROUND, SIZE EQUIPMENT GROUNDINGCONDUCTOR TO BE SAME SIZE AS THE PHASECONDUCTORS.
"HH": NEUTRAL CURRENTS EXIST DUE TO HIGH HARMONIC"NONLINEAR" LOADS. CURRENT CARRYINGCONDUCTORS DERATED ACCORDINGLY. PROVIDE THEIG/HH SIZE FOR THE EQUIPMENT GROUNDINGCONDUCTOR.
"IG": INCLUDE IG (INSULATED/ISOLATED GROUNDCONDUCTOR) SCHEDULED ALONG WITH THE GRO
