5. Making A Connection - EDC Romfor A Connection.pdfBroken Cable, Shackles Bolts, Inserts, Keepers,...

Romfor International Ltd.

MA

KIN

G A

CO

NN

EC

TIO

N

MAKING A

CONNECTION

MAKING A

CONNECTION

BackupHand-ChainBackupHand-Chain


MAKING A

CONNECTION

MAKING A

CONNECTION

Backup HandBackup Hand

TO

P D

RIV

E

DR

IL

L P

IP

E

TOP DRIVE

DRILL PIPE

TOP DRIVE

DRILL PIPE

Romfor International Ltd. Backup Hand

STEP SUB PROCEDURE REMARKS

TOP DRIVE DRILL PIPE

MAKING A CONNECTION

. 1

PPE Requirements - Hard Hat, Glasses, Work

Gloves, Steel Toe Shoes, Back Support

Prior to the first connection, review JSA

Inspect Equipment: Lines, Shackles, Slips, Collar

Clamp, Tong and Tong Hanger

Tong and Tong Hanger

Lines (proper length)

Slips

Upon the Driller’s instruction, assist in setting the

slips.

STAND CLEAR of elevators while connection is

broken and Top Drive assembly is being raised.

CONNECTION TO JOINT IN MOUSE HOLE - If

required, assist with pulling slips in Mouse Hole.

Slack, Missing parts, Damage,

Wear, Dies, Keepers, Tong

Heads

0

1

2

3

4

4

1

2

1

2

3

4

OR

Dies, Keepers, Tong Heads

Broken Cable, Shackles

Bolts, Inserts, Keepers, Cleaned

and Doped, Handle Condition

Avoid drilling fluids.

Verify elevators are properly

latched.

WATCH OUT FOR TRAPPED

TORQUE. Lay slips on side

away from rotary table.

CONNECTION TO STAND IN DERRICK - STAND CLEAR

until ready to assist with stabbing pipe/stand.

Assist with stabbing pipe/stand.

Upon Driller’s instructions, unlatch lead tongs and

assist in pulling the slips using proper lifting

techniques.

Assist in cleaning the rig floor, or follow Driller’s

instructions.

END OF PROCEDURE

5

6

7

1

1


MAKING A

CONNECTION

MAKING A

CONNECTION


TO

P D

RIV

E

DR

ILL C

OLLA

R

TOP DRIVE

DRILL COLLAR

TOP DRIVE

DRILL COLLAR



TOP DRIVE DRILL COLLAR

MAKING A CONNECTION

. 1

PPE Requirements- Hard Hat, Glasses Work Gloves,

Steel Toe Shoes, Back Support


Inspect Equipment: Lined, Shackles, Slips, Collar




Slips

Upon the Driller’s instruction, assist setting the slips.

When drill collar clamp is in place, install pin and

tighten clamp properly.

STAND CLEAR while pump-through-lift-sub connection

is broken and Top Drive assembly is being raised.


Wear, Dies Keepers, Tong Heads

0

1

2

3

4

5

6

7

8

9

1

2

1

2

3

4

THE PUMP THRU CONNECTION IS BROKEN





Minimum of two people.

FOLLOW INSTALLATION

PROCEDURES PER JSA.

Avoid tongs and snub lines

Unchain tongs from A-LEG.

Latch back-up tongs onto drill collar in Rotary Table,

using proper tong handles.

STAND CLEAR while lead tongs are latched onto

pump-through-sub.

Make the back-up tongs bite at the same time the

lead tongs bite; using the proper tong handles.

Keep the back-up tongs biting while the Driller breaks

the connection.

THE DRILL COLLAR CONNECTION IS BROKEN



MAKING A CONNECTION


2

10

11

12

After back-up tongs have been unlatched; chain back-

up tongs to A-leg.

After Rotary Table stops, unlatch lead tongs.

Assist in stabbing pump-through-sub into drill collar in

Mouse Hole.

Place chain-tong on pump-through-lift-sub.

Make up pump-through-sub with chain-tongs.

Remove chain-tongs and STAND CLEAR while drill

collar is being raised from Mouse Hole.

Assist in stabbing the drill collar from Mouse Hole into

the drill collar in the Rotary Table.

Upon Driller instruction, and lead tongs are latched

onto drill collar in Rotary Table, latch make up tongs

onto top drill collar using proper tong handles, and

make tongs bite.

Upon Driller’s instruction, STAND CLEAR while

connection is being torqued.

13

14

15

16

THE DRILL COLLAR CONNECTION IS TIGHT

Upon Driller instructions, unlatch lead tongs.

After back-up tongs are unlatched, chain back-up

tongs to A-leg.

Loosen nut on drill collar clamp and remove pin.

Assist in pulling the slips, using proper lifting

techniques.


instructions.

END OF PROCEDURE

Lay slips on side away from

rotary table

17

18

19

20

21

22

23


MAKING A

CONNECTION

MAKING A

CONNECTION


KE

LLY

S

PIN

NE

R

DR

IL

L P

IP

E

KELLY SPINNER

DRILL PIPE

KELLY SPINNER

DRILL PIPE



KELLY SPINNER DRILL PIPE

MAKING A CONNECTION

. 1


Gloves, Steel toe Shoes, Back Support






Slips

AFTER THE ROTARY TABLE STOPS, unchain back-

up tongs from A-LEG


slips.

Set Slips, using proper lifting techniques

Latch back-up tongs onto bottom joint in Rotary Table,


STAND CLEAR while lead tongs are latched onto Kelly.


lead tongs bite, using the proper tong handles.


the connection


Wear, Dies, Keepers, Tong Heads

0

1

2

3

4

5

6

7

8

9

1

2

1

2

3

4

THE CONNNECTION IS BROKEN






Avoid tongs and snub lines.

Stay Clear of Break Out Cable

ROTATING OUT WITH THE ROTARY TABLE - Before

rotating our, the Lead Tong Hand unlatches lower tongs.

1



MAKING A CONNECTION


2

9

9

Hold back-up tongs clear while Driller rotates out.

AFTER KELLY STOPS TURNING, and the Lead

Tong Hand unlatches bottom set of tongs. Remove

bottom set of tongs.

10

11

12

13

OR

REVERSING OUT WITH THE KELLY SPINNER -

Before spinning out, unlatch the top set of tongs,

using the proper tong handles.

Make back-up tongs bite on joint in Rotary Table,

using the propr tong handles, while Driller reverses out

Kelly.

AFTER KELLY STOPS TURNING, and the Lead Tong

Hand unlatches bottom set of tongs. Remove bottom

set of tongs.

Hold bottom set of tongs clear of Kelly.

STAND CLEAR while the Driller picks up on the Kelly.

Assist with stabbing Kelly into the joint in the Mouse

Hole

STAND CLEAR, with tongs, while Driller spins Kelly.

After the Kelly stops, latch back-up tongs onto Kelly.

Make the back-up tongs bite as the connection is

tightened, using the proper tong handles.

THE CONNECTION IS TIGHT

Do not get in Driller’s view.

Keep feet clear of the rotary

table and slip handles.

14

15

16

2

3



1

2

3

4

Unlatch the bottom set of tongs.

Hold back-up tongs clear while the Driller pulls the

Kelly joint out of the Mouse Hole.

Assist in stabbing the joint from Mouse Hole into the

joint in the Rotary Table.

17




MAKING A CONNECTION

3

After the Kelly stops spinning, latch the back-up tongs

on Kelly joint, using the proper tong handles.




rotary table

18


Unlatch the bottom set of tongs, using the proper tong

handles.

Hold back-up tongs clear and assist in pulling the

slips, using proper lifting techniques.

Chain back-up tongs to A-leg.


instructions.

19

20

21

22

23

END OF PROCEDURE


MAKING A

CONNECTION

MAKING A

CONNECTION


KE

LLY

S

PIN

NE

R

DR

ILL C

OLLA

R

KELLY SPINNER

DRILL COLLAR

KELLY SPINNER

DRILL COLLAR



KELLY SPINNER DRILL COLLAR

MAKING A CONNECTION

. 1

PPE Requirements - Hand Hat, Glasses Work Gloves,





Tong and Tong Hanger Heads


Slips

After the rotary table stops, and upon the Driller’s

instruction, assist in setting the slips.

Set slips, using proper lifting techniques






STAND CLEAR while lead tongs are latched onto

Kelly. Avoid tongs and snub lines.




the connection.


Wear, Dies Keepers, Tong Heads

0

1

2

3

4

5

6

7

8

9

1

2

1

2

3

4

THE CONNECTION IS BROKEN

Dies, Keepers, Tong





FOLLOW INSTALLATION

PROCEDURES PER JSA.




MAKING A CONNECTION


2

10

10

11


rotating out, the Lead Tong Hand unlatches lower tongs.


AFTER ROTARY STOPS, unlatch lead tongs, using

the proper tong handles.

12

13

14

15

16




1

2

3

OR


Before spinning out, unlatch the top set of tongs,

using the proper tong handles.

Make back-up tongs bite on drill collar in Rotary Table,

using the proper tong handles, while Driller reverses

out Kelly.

AFTER KELLY STOPS TURNING, lead tong Hand

unlatches bottom set of tongs.


Assist with stabbing Kelly into the drill collar in the

Mouse Hole.

STAND CLEAR, with tongs, while Driller spins Kelly.



tightened, using the propr tong handles.



Hold back-up tongs clear while the Driller pulls the drill

collar out of the Mouse Hole.


Avoid tongs ad snub lines.

1

2

3

17




MAKING A CONNECTION

3



After the Kelly stops spinning, latch the back-up tongs

on drill collar, using the proper tong handles.



18

19

20

21

22


Unlatch the bottom set of tongs, using the proper tong

handles.

After back-up tongs are unlatched, chain back-up

tongs to A-leg.



techniques.


instructions.

END OF PROCEDURE


rotary table

23

24

25

Romfor Interntional Ltd.

MAKING A

CONNECTION

MAKING A

CONNECTION


SPIN

NIN

G C

HA

IN

DR

IL

L P

IP

E

SPINNING CHAIN

DRILL PIPE

SPINNING CHAIN

DRILL PIPE



SPINNING CHAIN DRILL PIPE

MAKING A CONNECTION

. 1








Slips

AFTER THE ROTARY TABLE STOPS, unchain back-

up tongs from A-LEG


slips.

Set Slips, using proper lifting techniques.

Latch back-uo tongs onto bottom joint in Rotary Table,



Make the back -up tongs bite at the same time the



the connection.



0

1

2

3

4

5

6

7

8

9









ROTATING OUT WITH THE ROTARY TABLE -

Before rotating out, the Lead Tong Hand unlatches

lower tongs.

Hold back-up tongs clear while Driller rotates out. Do not get in Driller’s view.

Keep feet clear of the Rotary

Table and slip handles.

0

2

1

2

3

4

1

2



MAKING A CONNECTION


2

9

9



10

11

12

13

OR

REVERSING OUT WITH SPINNING CHAIN - Before

spinning out, unlatch the top set tongs, using the

proper tong handles.

Wrap chain, clockwise, aroung Kelly-saver-sub.

While Driller is pulling on chain, MAKE SURE your

hands and fingers are in proper position. Control

spinning chain, especially tail, while reversing out Kelly.

AFTER KELLY STOPS TURNING, remove excess

chain from Kelly-saver-sub and wrap, clockwise, onto

the joint in Mouse Hole.



Hole.

STAND CLEAR while Lead Tong Hand latches back-

up tong onto Kelly-saver-sub.



spinning chain, especially tail, while spinning joint in

Mouse Hole onto Kelly.

AFTER JOINT IN MOUSE HOLE STOPS TURNING,

remove excess chain.

Move to back-up tong position. STAND CLEAR while

Lead-Tong Hand latches lead tongs onto Kelly joint.




MAKE SURE spinning chain is

placed into one-gallon bucket.

14

15

16

3

MAKE SURE not to cross chain.

MAKE SURE to hold proper

tension on tail of chain.

1

2

3

4

Unlatch the bottom set of tongs.17

MAKE SURE stripper rubber is

on joint in Mouse Hole before

wrapping chain.


Move to position behind Mouse

Hole.




MAKING A CONNECTION

After Lead Tongs Hand latched tongs onto joint in

rotary, wrap spinning chain, counter clockwise, onto

tool joint while the Driller pulls the Kelly joint out of the

Mouse Hole.



While Driller is pulling on chain, throw and control

spinning chain using proper technique while Kelly joint

is being spun up.

After the Kelly joint stops spinning, remove excess

chain and latch the back-up tongs on Kelly joint, using




MAKE SURE stripper rubber

does not ride up on tool joint.18


Unlatch the bottom set of tongs, using the proper

tong handles.

Hold back-up tongs clear and assist in pulling the

slips, using proper lifting techniques.

Chain back-up tongs to A-leg.


instructions.

19

20

21

22

23

END OF PROCEDURE

24

25

26

MAKE SURE cover is placed on

Mouse Hole.


tension on tail of chain. MAKE

SURE your hands and fingers

are in proper position.


rotary table.

3


MAKING A

CONNECTION

MAKING A

CONNECTION


SPIN

NIN

G C

HA

IN

DR

ILL C

OLLA

R

SPINNING CHAIN

DRILL COLLAR

SPINNING CHAIN

DRILL COLLAR



SPINNING CHAIN DRILL COLLAR

MAKING A CONNECTION

. 1








Slips

After the rotary table stops, and upon the Driller’s

instruction, assist in setting the slips.

Set Slips, using proper lifting techniques



Unchain tongs from A-LEG







the connection.



0

1

2

3

4

5

6

7

8

1

2

1

2

3

4


Dies, Keepers, Tong Head

Broken Cable, Shackle

Bolts, Inserts, Keepers,Cleaned



FOLLOW INSTALLATION

PROCEDURES PER JSA.


Stay Clear of Break Out Cable9



MAKING A CONNECTION


2

10

10


rotating out, the Lead Tong Hand unlatches lower tongs.




11

12

13

14

OR

REVERSING OUT WITH SPINNING CHAIN - Before

spinning out, unlatch the top set of tongs, using the


Wrap chain, clockwise, around Kelly-saver-sub.



spinning chain, especially tail, while reversing out Kelly.

AFTER KELLY STOPS TURNING, remove excess

chain from Kelly-saver-sub.



Mouse Hole.

Wrap chain, counter-clockwise, around Kelly-saver-

sub.



spinning chain, especially tail, while spinning Kelly

into drill collar in Mouse Hole.

AFTER JOINT IN MOUSE HOLE STOPS TURNING,

remove excess chain.








15

16

17

MAKE SURE spinning chain is

placed into one-gallon bucket.


1

2

3


tension on tail of chain.



1

2

3

4




MAKING A CONNECTION

3


After lead tongs are latched to the drill collar in the

Rotary Table, wrap chain counter-clockwise on drill

collar in rotary table.

Assist in stabbing the drill collar from Mouse Hole

into the drill collar in the Rotary Table.

“Walk” chain up onto drill collar.



spinning chain, especially tail, while spinning Kelly

into drill collar in Rotary Table.

AFTER KELLY AND DRILL COLLAR STOPS

TURNING, remove excess chain from drill collar.

Latch the back-up tongs on drill collar, using the





18

THE CONNECTION IS TIGHTENED

Unlatch the bottom set of tongs, using the proper

tong handles.

After back-up tongs are unlatched. chain back-up

tongs to A-leg.



techniques.


instructions.

19

20

21

22

23

END OF PROCEDURE

24

25

26


rotary table.

27

28

29

30


MA

KIN

G A

CO

NN

EC

TIO

N

MAKING A

CONNECTION

MAKING A

CONNECTION

DerrickmanDerrickman


MAKING A

CONNECTION

MAKING A

CONNECTION


TO

P D

RIV

E

DR

ILL C

OLLA

R

TOP DRIVE

DRILL PIPE

TOP DRIVE

DRILL PIPE

Romfor International Ltd. Derrickman



MAKING A CONNECTION

. 1

PPE Requirements - Hard Hat, Glasses, Work Gloves,


Review JSA for climbing derricks.

CONNECTION TO JOINT IN MOUSE HOLE - check

for flow and maintain the mud system.

Follow Driller’s instructions.

OR

CONNECTION TO STAND IN DERRCK - Before the first

connection is made. Review JSA for climbing derricks.

Latch stand as elevators clear the monkey board.

Return to rig floor. Check for flow and maintain the

mud system.


END OF PROCEDURE

Review fall protection requirements.

If the Derrickman is required

to work in Derrick, the

Derrickman is to be 100%

tied-off at all times.

Two-way communications is

required betwees the Driller

and the Derrickman.

Notify the Driller immediately of

ANY problems with mud system.



0

1

2

2

3

1

2

1

2

3


MAKING A

CONNECTION

MAKING A

CONNECTION


TO

P D

RIV

E

DR

ILL C

OLLA

R

TOP DRIVE

DRILL COLLAR

TOP DRIVE

DRILL COLLAR




MAKING A CONNECTION

. 1

PPE Requirements- Hard Hat, Glasses, Work


Prior to making the first connection, review JSA. At

the start of the tour hold Safety Meetings on the jobs.

During the connection procedure, check for flow and

maintains the mud system.


END OF PROCEDURE







and the Derrickman.



0

1

2

3


MAKING A

CONNECTION

MAKING A

CONNECTION


KE

LLY

S

PIN

NE

R

DR

IL

L P

IP

E

KELLY SPINNER

DRILL PIPE

KELLY SPINNER

DRILL PIPE




MAKING A CONNECTION

. 1

PPE Requirements- Hard Hat, Glasses, Work Gloves,







END OF PROCEDURE







and the Derrickman.



0

1

2

3


MAKING A

CONNECTION

MAKING A

CONNECTION


KE

LLY

S

PIN

NE

R

DR

ILL C

OLLA

R

KELLY SPINNER

DRILL COLLAR

KELLY SPINNER

DRILL COLLAR




MAKING A CONNECTION

. 1








END OF PROCEDURE







and the Derrickman.



0

1

2

3


MAKING A

CONNECTION

MAKING A

CONNECTION


SPIN

NIN

G C

HA

IN

DR

IL

L P

IP

E

SPINNING CHAIN

DRILL PIPE

SPINNING CHAIN

DRILL PIPE




MAKING A CONNECTION

. 1








END OF PROCEDURE







and the Derrickman.



0

1

2

3


MAKING A

CONNECTION

MAKING A

CONNECTION


SPIN

NIN

G C

HA

IN

DR

ILL C

OLLA

R

SPINNING CHAIN

DRILL COLLAR

SPINNING CHAIN

DRILL COLLAR




MAKING A CONNECTION

. 1








END OF PROCEDURE







and the Derrickman.



0

1

2

3


MA

KIN

G A

CO

NN

EC

TIO

N

MAKING A

CONNECTION

MAKING A

CONNECTION

DrillerDriller


MAKING A

CONNECTION

DrillerDriller

MAKING A

CONNECTION

TO

P D

RIV

E

DR

IL

L P

IP

E

TOP DRIVE

DRILL PIPE

TOP DRIVE

DRILL PIPE

Romfor International Ltd. Driller



MAKING A CONNECTION

. 1

PPE Requirements - Hard Hat, Glasses Work



Know string weight, torque requirements, pump

pressure, drilling RPM, etc.

Fit for duty check on all Hands.

Verify that equipment has been inspected and is in

good working condition.

If necessary, blow horn to notify crew for connection.

READY FOR CONNECTION

Kick out Auto-Driller and drilling recorder, if required.

Unchain break handle.

Stop rotation of Top Drive.

If required, release back torque - SLOWLY.

When Top Drive comes to a complete stop, raise drill

string off bottom.

Depending upon hole condition, ream back to bottom,

if necessary.

WHEN TOOL JOINT IS AT PROPER POSITION (slip

setting position), kick out pumps.

Instruct Floor Hands to set slips.

Slack off on drill string, paying close attention to

weight indicator.

If slide drilling, insure Top Drive

brake is released before making

connection.

WATCH WEIGHT INDICATOR

FOR DRAG.

MAKE SURE the slips are set

properly.

DO NOT EXCEED TRAVELLING

BLOCK ASSEMBLY WEIGHT.

0

1

2

3

4

5

6

7

8

9

10

1

2

3

4

1

2



Derrickman is to be 100% tied-

off at all times.



and the Derrickman.

NEVER lock Rotary Table

except to make-up bit.



MAKING A CONNECTION


2

11

12

13

14

15

16

17

18

19

19

20

21

Check pump gauge for zero pressure and close Top

Drive Safety Valve (remote).

Close gripper around tool joint.

Engage torque boost to break connection 1/2 round.

Disengage torque boost after connection is broke.


REVERSE OUT WITH THE TOP DRIVE.

Release gripper.

Instruct Hands to watch lines and proper clearance of

Top Drive assembly in derrick during raising and

lowering procedures.

Raise travelling equipment and Top Drive out of joint in

rotary.

CONNECTION TO JOINT IN MOUSE HOLE - Using

pipe handler control, latch onto joint in Mouse Hole

with elevators.

Raise pipe out of Mouse Hole keeping pipe centered

using handler.

OR

RE-CHECK GAUGE FOR

TRAPPED PRESSURE.

MAKE SURE Top Drive

handler is properly locked.


Use low drum.

CONNECTION TO STAND IN DERRICK - Run Top

Drive assembly up derrick, while extending link tilts, to

designated point above monkey board for connection

onto stand in derrick.

Once elevators are latched by Derrickman, pick up

slowly with Top Drive while retracting extended link

tilts.

Pick up for proper positioning over tool joint in rotary

table.

Engage “Spin/Maintain”, then lower pipe into tool joint

in rotary.WATCH WEIGHT INDICATOR.

MAKE SURE employees are in

safe position.

1

2

1

2

Before moving blocks, verify that

Derrickman is 100% TIED-OFF.

Establish two-way communication

between Driller and Derrickman.




MAKING A CONNECTION

3

Continue to slack off until joint is made up.

When Top Drive stops spinning, wait on proper

placement of lead tongs, then torque connection

properly.

WATCH WEIGHT INDICATOR.22

23

24

25

26

27

28

29

30

31


DO NOT OVER-TORQUE.

MAKE SURE Hands are clear.Use Top Drive to raise drill string high enough to

release all torque before instructing Floor Hands to

pull slips.

MAKE SURE slips are pulled and Floor Hands are

clear, then open Top Drive Safety Valve (remote).

Engage the mud pump(s), at slow rate, and verify

returns.

IF MAKING PIPE UP IN MOUSE HOLE, DO NOT

RESUME DRILLING UNTIL MOUSE HOLE STAND IS

MADE UP AND ALL FLOOR HANDS ARE CLEAR.

Bring pump(s) and RPM up to proper speed.

Lower the drill sting and set proper weight on bit.

Chain the brake and engage drilling recorder.

Attach automatic Driller to break handle and engage.

Add joint/stand to pipe tally. Mark recorder as

needed.

Watch pressure gauge.

If required, refer to pipe

handling procedures.

If required. set PVT and Flow

END OF PROCEDURE

1

2


MAKING A

CONNECTION

DrillerDriller

MAKING A

CONNECTION

TO

P D

RIV

E

DR

ILL C

OLLA

R

TOP DRIVE

DRILL COLLAR

TOP DRIVE

DRILL COLLAR




MAKING A CONNECTION

. 1













Stop rotation of Top Drive.


When Top Drive comes to a complete stop, raise drill

string off bottom.

Depending upon hole condition, ream back to

bottom, if necessary.

WHEN DRILL COLLAR CONNECTION IS AT

PROPER POSITION (slip setting position), kick out

pumps.

Instruct Floor Hands to set slips and install drill collar

clamp.


weight indicator.

Watch weight indicator for drag.

0

1

2

3

4

5

6

7

8

9

10

1

2

3

4

1

2

MAKE SURE slips and clamp

are installed properly.

DO NOT exceed traveling block

assembly weight.




off at all times.



and the Derrickman.





MAKING A CONNECTION


2

11

12

Check pump gauge for zero pressure and close Top

Drive Safety Valve (remote).

Close gripper around pump thru lift sub.

Engage torque boost to break connection 1/2 round.

Disengage torque boost after pump thru connection is

broken.

13

14

15

16


REVERSE OUT WITH THE TOP DRIVE.

Release gripper.

Raise travelling equipment and Top Drive until elevators

are against top of pump-thru-sub.

When tongs, and crew members, are in proper break

out position for pump-thru-sub, engage break out cat-

head pulling lead tongs and breaking connection.

THE COLLAR CONNECTION IS BROKEN

RE-CHECK GAUGE FOR

TRAPPED PRESSURE.

MAKE SURE Top Drive

handler is properly locked.

17 Avoid drilling fluids.

MAKE SURE crew members

feet are clear of the rotary table

and slip handles.

Engage rotary - SLOWLY- rotating out drill collar from

pump-thru-lift-sub. BE AWARE OF BACK TORQUE.

AFTER ROTARY STOPS - Verify tongs and crew

members are in proper position, pick up on Top Drive.

Instruct Floor Hands to watch lines and proper

clearance of Top Drive assembly in derrick during

raising and lowering procedures.

Raise travelling equipment and Top Drive until elevators

are against top of pump-thru-sub out of drill collar in

Rotary.


18

19

20

21

22 Instruct Hands to watch lines

and proper clearance of Top

Drive assembly in derrick during

raising and lowering procedures.





MAKING A CONNECTION

3

CONNECTION TO DRILL COLLAR IN MOUSE HOLE -

Using pipe handler control, extend pump-thru-sub over

drill collar in Mouse Hole.

Lower sub into drill collar in Mouse Hole.

Instruct Floor Hands to make up pump-thru-sub with

chain tongs.

Pick up drill collar out of Mouse Hole keeping pipe

centered using handler.

Pick up for proper positioning over drill collar in rotary

table.

Lower drill collar to stab drill collar into drill collar in

rotary table.

Engage “Spin/Maintain”, then lower Top Drive into

pump-thru-sub.

Continue to slack off until drill collar and pump-thru-

sub is made up and torqued properly.

FOR COLLAR CONNECTION - When pump-thru-sub

is properly torqued, wait on proper placement of tongs,

then torque collar connection properly.

Use low drum.

23


WATCH WEIGHT INDICATOR.

MAKE SURE employees are in

safe position.


DO NOT OVER-TORQUE.

Use Top Drive to raise drill string high enough to

release all torque before instructing Floor Hands to

remove collar clamp.

Instruct Floor Hands to remove drill collar clamp.

Use top Drive to raise drill string high enough to make

sure slips are pulled and Floor Hands are clear, then

open Top Drive Safety Valve (remote).

Engage the mud pump(s), at slow rate, and verify

returns.

DO NOT RESUME DRILLING UNTIL NEXT DRILL

COLLAR IS PLACED IN MOUSE HOLE AND ALL

FLOOR HANDS ARE CLEAR.

24

25

26

27

28

29

30

31

32

TIGHTEN WITH CAT-HEAD.

DO NOT OVER-TORQUE.

MAKE SURE Floor Hands are

clear.

Watch pressure gauge.

33

34

35

36



MAKING A CONNECTION


4

37

38

Bring pump(s) and RPM up to proper speed

Lower the drill string and set proper weight on bit.

Chain the break engage drilling recorder.

Attach automatic Driller to break handle and engage.

Add collar to pipe tally. Mark recorder as needed.

39

40

END OF PROCEDURE

If required, set PVT and Flow Sho.

41


MAKING A

CONNECTION

DrillerDriller

MAKING A

CONNECTION

KE

LLY

S

PIN

NE

R

DR

IL

L P

IP

E

KELLY SPINNER

DRILL PIPE

KELLY SPINNER

DRILL PIPE




MAKING A CONNECTION

. 1













Kick out the Rotary Table.


When rotary comes to a complete stop, raise drill

string off bottom.



WHEN KELLLY BUSHING CLEARS ROTARY

TABLE, kick out pumps.

Raise tool joint 10 ft (minimum) above rotary table.

Lower the drill string to the position needed to set the

slips.



FOR DRAG.

Be aware of operator

requirements.


properly.

0

1

2

3

4

5

6

7

8

9

10

11

12

1

2

3

4




off at all times.



and the Derrickman.





MAKING A CONNECTION


2

13

14


weight indicator.

As the Floor Hands put on the tongs, check the pump

pressure gauge and instruct Motorman to close Kelly-

Safety-valve (if required).


out position, engage break out cat-head pulling lead

tongs and breaking connection.

15

16

16

17


ROTATING OUT WITH THE ROTARY TABLE - After

bottom tongs are removed and clear, engage rotary -

SLOWLY - rotating out drill string.


members are in proper position, pick up on Kelly.

OR



18

CHECK FOR TRAPPED

PRESSURE.

BE AWARE OF TIGHT

CONNECTIONS.

1

2

REVERSING OUT WITH THE KELLY SPINNER - After

top tongs are removed and cleared, engage left hand

Kelly spinner motor - SLOWLY - reversing out Kelly.

AFTER KELLY STOPS TURNING - Verify tongs and

crew members are in proper position, pick up on Kelly.

As the Kelly is moved to the Mouse Hole, lower the

Kelly into the box of the joint in the Mouse Hole.

Verify tongs and crew members are in proper position,

engage the right hand Kelly spinner motor and spin

Kelly into joint in Mouse Hole.


engage make up cat-head pulling tongs to tighten

connection properly.

Verify tongs and crew members are in proper position

and the Kelly-Safety-valve is open, raise the Kelly joint

from Mouse Hole - SLOWLY.

BE AWARE OF BACK

TORQUE. MAKE SURE crew

members’ feet are clear of the

rotary table and slip handles.

19

20

1

2 MAKE SURE connection is

completely rotated out.

MAKE SURE all crew

members are in their proper

positions.

MAKE SURE connection is


MAKE SURE all crew

members are in their proper

positions.

SPIN IN SLOWLY. DO NOT

RUN INTO SNUB LINE.

DO NOT OVER TORQUE.

LOOK UP! Check Kelly hose

and travelling assembly for




MAKING A CONNECTION

3

Lower Kelly joint into the drill string in the Rotary

Table.

Verify tongs and crew members are in proper

position, then engage the right hand Kelly spinner

and rotate Kelly joint into drill string - SLOWLY.





BLOCK ASSEMBLY WEIGHT.21

CONNECTION IS TIGHT


RUN INTO SNUB LINE.

DO NOT OVER TORQUE.

Raise drill string allowing crew members to pull slips.

Engage the mud pump(s) and verify returns.

Lower the drill string and set Kelly bushings into rotary

table.

Engage the rotary table, AT SLOW SPEED

Wait for the crew members to place another joint of

drill pipe into the Mouse Hole.

Bring pump and rotary up to proper speed.


Chain the brake engage drilling recorder.

Attach automatic driller to break handle and engage.

Add joint to pipe tally. Mark recorder as needed.

22

23

24

25

26

27

28

29

30


Check for proper pressure.

Check for leaks.


END OF PROCEDURE

TRAVELLING ASSEMBLY

STATIONARY.


31

32

33


MAKING A

CONNECTION

DrillerDriller

MAKING A

CONNECTION

KE

LLY

S

PIN

NE

R

DR

ILL C

OLLA

R

KELLY SPINNER

DRILL COLLAR

KELLY SPINNER

DRILL COLLAR




MAKING A CONNECTION

. 1











Kick out Auto-Drilling and drilling recorder, if required.





string off bottom.



WHEN KELLY BUSHING CLEARS ROTARY




slips.

Instruct Floor Hands to set slips and install drill collar

clamp. MAKE SURE the slips are set properly.


FOR DRAG.


requirements.

0

1

2

3

4

5

6

7

8

9

10

11

12

1

2

3

4




off at all times.



and the Derrickman.





MAKING A CONNECTION


2

13

14


weight indicator.

As the Floor Hands put on the tongs, check the pump

pressure gauge and instruct Motorman to close Kelly-

Safety-valve (if required).




15

16

16

17




SLOWLY - rotating out drill string.



OR

DO NOT EXCEED

TRAVELLING BLOCK

18

ASSEMBLY WEIGHT.

CHECK FOR TRAPPED

PRESSURE.

BE AWARE OF TIGHT

CONNECTIONS.

1

2

REVERSING OUT WITH THE KELLY SPINNER - After

top tongs are removed and cleared, engage left hand

Kelly spinner motor - SLOWLY - reversing out Kelly.

AFTER KELLY STOPS TURNING - Verify tongs and

crew members are in proper position, pick up on Kelly.


Kelly into the box of the collar in the Mouse Hole.


engage the right hand Kelly spinner motor and spin

Kelly into collar in Mouse Hole.


engage the appropriate cat-head per torque

requirements. Pull tongs to tighten connection

properly.


and the Kelly-Safety-valve is open, raise the Kelly joint

from Mouse Hole - and drill collar from Mouse Hole -

SLOWLY.

BE AWARE OF BACK

TORQUE. MAKE SURE crew

members feet are clear of the

rotary table and slip handles.

19

20

1

2 MAKE SURE connection is


MAKE SURE all crew members

are in their proper positions.




RUN INTO SNUB LINE.

TIGHTEN COLLARS TO

RECOMMENDED TORQUE

REQUIREMENTS.



clearances.




MAKING A CONNECTION

3

Lower drill collar into the drill string in the Rotary

Table.

Verify tongs and crew members are in proper

position, then engage the right hand Kelly spinner

and rotate Kelly joint into drill string - SLOWLY.



requirements. Pull tongs at tighten connection properly.


BLOCK ASSEMBLY WEIGHT .21

CONNECTION IS TIGHT


RUN INT SNUB LINE.

TIGHTEN COLLARS TO

RECOMMENDED TORQUE

REQUIREMENTS.

Raise drill string allowing crew members to remove

drill collar clamp.




table.

Engage the Rotary Table, AT SLOW SPEED -

TRAVELLING ASSEMBLY STATIONARY.


drill collar into the Mouse Hole.






22

23

24

25

26

27

28

29

30




Check for leaks.

END OF PROCEDURE


If required, set PVT Flow Sho.

31

32

33

34


MAKING A

CONNECTION

DrillerDriller

MAKING A

CONNECTION

SPIN

NIN

G C

HA

IN

DR

IL

L P

IP

E

SPINNING CHAIN

DRILL PIPE

SPINNING CHAIN

DRILL PIPE




MAKING A CONNECTION

. 1





pressure, drilling RPM etc.











string off bottom.







slips.



FOR DRAG.


requirements.


properly.

0

1

2

3

4

5

6

7

8

9

10

11

12

1

2

3

4




off at all times.



and the Derrickman.





MAKING A CONNECTION


2

13

14

Slack-off on drill string, paying close attention to

weight indicator.

As the Floor Hands put on the tongs, the Driller

checks the pump pressure gauge and instructs

Motorman to close Kelly-Safety-valve (if required).




15

16

16

17



bottom tongs are removed and clear, engage rotary-

SLOWLY - rotating out drill string. BE AWARE OF

BACK TORQUE.



OR

DO NOT EXCEED TRAVELING


18

CHECK FOR TRAPPED

PRESSURE.

BE AWARE OF TIGHT

CONNECTIONS.

1

2

REVERSING OUT WITH SPINNING CHAIN - After

top tongs are removed and cleared and spinning

chain is wrapped, clockwise, around Kelly-saver-sub

- SLOWLY ENGAGE MAKE UP CAT-HEAD,

reversing the Kelly out - SLOWLY.

AFTER KELLY STOPS TURNING - Verify tongs,

spinning chain, and crew members are in proper

position, pick up on Kelly.




engage the make up cat-head and spin the joint in

Mouse Hole into the Kelly.



and slip handles.

MAKE SURE Kelly connection

is completely rotated out before

picking up.

MAKE SURE all employees

are in proper position,

especially Floor Hands, before

engaging cat-head.


is completely reversed out

before picking up and make sure

the spinning chain is wrapped

properly on joint in Mouse Hole,

before picking up Kelly.


are in proper position, BE AWARE

of feet and hand damage potential.


RUN INTO SNUB LINE.

1

2




MAKING A CONNECTION

3





and the Safety valve is open, raise the Kelly joint from

Mouse Hole - SLOWLY.

Verify tongs, spinning chain, and crew members are in

proper position.

Lower Kelly joint into the drill string in the rotary table,

DO NOT EXCEED TRAVELING BLOCK ASSEMBLY

WEIGHT, then engage the make up cat-head and

rotate Kelly joint into drill string - SLOWLY.




TIGHTEN COLLARS TO

RECOMMENDED TORQUE

REQUIREMENTS. Do not over torque.

19

CONNECTION IS TIGHT



clearances.

MAKE SURE chain is in proper

position.



Lower the drill string and set Kelly bushings into

rotary table.

Engage the rotary table, AT SLOW SPEED


drill pipe into the Mouse Hole


20

21

22

23

24

25

26

27

28

29

MAKE SURE chain is thrown to

proper position on Kelly joint

while engaging cat-head.

MAKE SURE all employees are

in proper position while making

up connection.

Be aware of pinch points.

Do not over torque.


Check for properpressure.

Check for leaks.


TRAVELING ASSEMBLY

STATIONARY.



MAKING A CONNECTION


4

30

31

32

33





END OF PROCEDURE



MAKING A

CONNECTION

DrillerDriller

MAKING A

CONNECTION

SPIN

NIN

G C

HA

IN

DR

ILL C

OLLA

R

SPINNING CHAIN

DRILL COLLAR

SPINNING CHAIN

DRILL COLLAR




MAKING A CONNECTION

. 1
















string off bottom.

Depending upon hole condition, ream back t bottom,

if necessary.



Raise collar connection (joint) 10 ft (minimum) above

Rotary Table.


slips.

Instruct Floor Hands to set slips and install collar

clamp.


FOR DRAG.


requirements.

MAKE SURE THE SLIPS AND

CLAMPS ARE PROPERLY

INSTALLED

0

1

2

3

4

5

6

7

8

9

10

11

12

1

2

3

4




off at all times.



and the Derrickman.





MAKING A CONNECTION


2

13

14


weight indicator.

As the Floor Hands put on the tongs, the Driller

checks the pump pressure gauge and instructs

Motorman to close Kelly-Safety-valve (if required).




15

16

16

17


ROTATING OUT WITH TH ROTARY TABLE - After


SLOWLY - rotating out drill string. BE AWARE OF

BACK TORUE.



OR

DO NOT EXCEED TRAVELING


17

CHECK FOR TRAPPED

PRESSURE.

BE AWARE OF TIGHT

CONNECTIONS.

1

2

REVERSING OUT WITH SPINNING CHAIN - After

top tongs are removed and cleared and spinning

chain is wrapped, clockwise, around Kelly-saver-sub

- SLOWLY ENGAGE MAKE UP CAT-HEAD,

reversing the Kelly out - SLOWLY.

AFTER KELLY STOPS TURNING - Verify tongs,

spinning chain, and crew members are in proper

position, pick up on Kelly.




engage the make up cat-head and spin the KELLY into

the drill collar in the Mouse Hole.



and slip handles.


completely rotated out

MAKE SURE all employees

are in proper position,

especially Hands, before

engaging cat-head.


is completely reversed out

before picking up and make sure

the spinning chain is wrapped

properly on joint in Mouse Hole,

before picking up Kelly.


are in proper position. Be

aware of pinch points.


RUN INTO SNUB LINE.

1

2

18

Romfor INternational Ltd. Driller



MAKING A CONNECTION

3



requirements, Pull tongs to tighten connection properly.


and the Kelly-Safety-valve is open, raise the drill

collar from Mouse Hole - SLOWLY.

Verify tongs, spinning chain, and crew members are in

proper position.

Lower Kelly and drill collar into the drill collar in the

rotary table. DO NOT EXCEED TRAVELING BLOCK

ASSEMBLY WEIGHT, then engage the make up cat-

head and rotate Kelly joint into drill string - SLOWLY.



requirements. Pull tongs to tighten connection properly.

TIGHTEN COLLLARS TO

RECOMMENDED TORQUE

REQUIREMENTS

19

CONNECTION IS TIGHT



clearances.

MAKE SURE chain is in proper

position.

Raise drill string allowing crew members to remove

drill collar clamp.




table.

Engage the Rotary Table, AT SLOW SPEED


drill collar into the Mouse Hole.


20

21

22

23

24

25

26

27

28

29

30

MAKE SURE chain is “walked” up

by hand to proper position on drill

collar BEFORE ENGAGING CAT -

HEAD. MAKE SURE all crew

members are in proper position,

while making up connection.

Be aware of pinch points.

TIGHTEN COLLARS TO

RECOMMENDED TORQUE

REQUIREMENTS.




Check for leaks.


TRAVELLING ASSEMBLY

STATIONARY.



MAKING A CONNECTION


4

31

32





33

34

END OF PROCEDURE



MA

KIN

G A

CO

NN

EC

TIO

N

MAKING A

CONNECTION

MAKING A

CONNECTION

Floorman-Lead TongFloorman-Lead Tong


MAKING A

CONNECTION

MAKING A

CONNECTION

Floorman -

Lead Tong

Floorman -

Lead Tong

TO

P D

RIV

E

DR

IL

L P

IP

E

TOP DRIVE

DRILL PIPE

TOP DRIVE

DRILL PIPE

Romfor International Ltd. Floorman-Lead Tong



MAKING A CONNECTION

. 1


Steel Toe Shoes, Back Support.

Prior to the first connection, review JSA.

Inspect Equipment: Lines, Shackles, Slips, Collar Clamp,

Tong and Tong Hanger.


Lines (proper length).

Slips.

Upon instruction by the Driller, assist in setting the slips.

STAND CLEAR of elevators while connection is

broken and Top Drive assembly is raised.

CONNECTION JOINT IN MOUSE HOLE - If required,

assist with slips in Mouse Hole.



Heads.

Dies, Keepers, Tong Heads.

Broken Cable, Shackles.

Bolts, Inserts, Keepers, Cleanedand Doped, Handle Condition.


Verify elevators are properly

latched.

Derrickman is required to be

100% Tied-Off at all times.

WATCH OUT FOR TRAPPED

TORQUE. Lay slips on side

away from rotary table.

0

1

2

3

4

4

5

6

7

8

9

1

2

1

2

3

4

OR

CONNECTION TO STAND IN DERRICK - STAND

CLEAR until ready to assist with stabbing pipe/stand.

Dope tool-joint in rotary and assist with stabbing

pipe/stand.

Latch lead tongs onto tool-joint in rotary table, using

proper tong handles and make tongs bite.

Upon Driller instructions and after Back-Up Hand

unlatches lead tongs, hold lead tongs clear and assist

in pulling the slips using proper lifting techniques.

Chain lead tongs to A-leg.

Assist in cleaning the rig floor, and follow Drillers

instructions.

END OF PROCEDURE


MAKING A

CONNECTION

MAKING A

CONNECTION

Floorman -

Lead Tong

Floorman -

Lead Tong

TO

P D

RIV

E

DR

ILL C

OLLA

R

TOP DRIVE

DRILL COLLAR

TOP DRIVE

DRILL COLLAR




MAKING A CONNECTION

1





Clamp, Tong and Tong Hanger.



Slips.

Upon instruction by the Driller, assist in setting the

slips.

Place drill collar clamp around collar and hold in place

until pin is in place and clamp is properly tightened.

Stand clear while pump-thru-lift-sub connection is

broken and Top Drive assembly is raised.

Wait until the back-up tongs are in place, on the

bottom joint and latched.

Place tong on the top joint and latch using the proper

handles.

Make the lead tongs bite at the same time the back-up

tongs bite, using the proper tong handles.

Keep the lead tongs biting while the Driller breaks the

pump-thru-sub-connection.



Heads.

0

1

2

3

4

5

6

7

8

9

1

2

1

2

3

4





and Doped, Handle Condition.

FOLLOW INSTALLATION

PROCEDURES PER JSA

DO NOT help pulling back-up

tongs. MAKE SURE Chain

Hand is out of the way.

Stay Clear of Break Out Cable.

Unlatch back-up tongs.



MAKING A CONNECTION

Floorman-Lead Tong

2

10

11

12

Keep the lead tongs biting while the Driller rotates

pump-thru-sub out of drill collar in rotary table.

After rotary table stops, and lead tongs are unlatched,

chain lead tongs to A-leg.

Assist in stabbing pump-thru-sub into drill collar in

Mouse Hole.

Assist with making up pump-thru-sub with chain-tongs.

Dope drill collar in rotary table.



Latch lead tongs onto drill collar in Rotary Table, using

proper tong handles, and make tongs bite.

Upon Driller’s instruction, stand clear while connection

is being torqued.

13

14

15

16

17

18


Rotary Table.

19


Upon Driller’s instructions, unlatch back up tongs.

After lead tongs are unlatched, chain lead tongs to A-leg.

Assist in removing the drill collar clamp by holding

proper handles as clamp is loosened and pin is

removed.

Remove clamp from drill collar and place in proper

location.

Assist in pulling the slips using proper lifting

techniques.

Assist in cleaning the rig floor, and follow Driller’s

instructions.

END OF PROCEDURE

20

21

22

23


MAKING A

CONNECTION

MAKING A

CONNECTION

Floorman -

Lead Tong

Floorman -

Lead Tong

KE

LLY

S

PIN

NE

R

DR

IL

L P

IP

E

KELLY SPINNER

DRILL PIPE

KELLY SPINNER

DRILL PIPE




MAKING A CONNECTION

. 1


Gloves, Steel Toe Shoes, Back Support.






Slips.

After the Rotary Table stops, unchain tongs from A-LEG.

Upon the Driller’s signal, assist in setting the slips.


Wait until the back-up tongs are in place, on the

bottom joint and latched.

Place tong on the top joint and latch, using the proper

handles.

Make the lead tongs bite at the same time the back-

up tongs bite, using the proper tong handles.


connection.



Heads.






Do not help pulling back-up

tongs. Make sure Chain Hand is

out of the way.


Keep feet clear of the rotary table

and slip handles.

0

1

2

3

4

5

6

7

8

9

1

2

1

2

3

4


ROTATING OUT WITH THE ROTARY TABLE -

Unlatch the lower tongs. Make the top tongs bite

using the proper tong handles while rotating out.

1



MAKING A CONNECTION


2

9

9

10

AFTER ROTARY STOPS, and Back-Up Hand un-

latches lead tongs, remove lead tongs.

11

12

13

14

15

16


2

1

2

17

OR


After Back-Up Hand unlatches lead tongs, hold lead

tongs clear of Kelly.

AFTER KELLY STOPS TURNING, unlatch bottom set

of tongs.

Place the lead tongs on the joint in the Mouse Hole.



Hole.

Make the lead tongs bite on the joint in the Mouse

Hole, using the proper tong handles, while the Driller

spins the Kelly.

After the Kelly stops, step back while the top tongs are

latched onto Kelly.

After the top tongs are on the Kelly, make the bottom

tongs bite.

Make the lead tongs bite as the connection is tight-

ened, using the proper tong handles.


Unlatch the top set of tongs, using the proper tong

handles.

Latch the lead tongs onto the joint in the Rotary Table.

Dope the connection in the Rotary Table as the Driller

pulls the joint out of the Mouse Hole.



18

19

20




MAKING A CONNECTION

3

Make the lead tongs bite on the joint in the Rotary

Table, using the proper tong handles, while the Driller

spins the Kelly-joint.

AFTER THE KELLY STOPS SPINNING, STAND CLEAR

while the top tongs are latched onto the Kelly-joint.

After the top set of tongs are latched, make the lead

tongs bite using the proper tong handles, while the

connection is tightened.

21

22

23

24

25

26

27



handles.


tongs clear and assist in pulling the slips, using proper

lifting techniques.

Chain lead tongs to A-leg.

Assist in cleaning the rig floor, or follow Driller instruc-

tions.

END OF PROCEDURE


rotary table.


MAKING A

CONNECTION

MAKING A

CONNECTION

Floorman -

Lead Tong

Floorman -

Lead Tong

KE

LLY

S

PIN

NE

R

DR

ILL C

OLLA

R

KELLY SPINNER

DRILL COLLAR

KELLY SPINNER

DRILL COLLAR




MAKING A CONNECTION

. 1









Slips.

After the Rotary Table stops, and upon the Driller’s

instructions, assist in setting the slips.


Wear, Dies,Keepers, Tong Heads.






FOLLOW INSTRUCTION

PROCEDURES PER JSA.Place drill collar clamp around collar and hold in place

until pin is in place and clamp is properly tightened.


STAND CLEAR until the back-up tongs are in place (on

the drill collar in the rotary) and are properly latched.

Place tong on the top joint and latch using the proper

handles.

Make the lead tongs bite at the same time the back-

up tongs bite, using the proper tong handles.


connection.


0

1

2

3

4

5

6

7

8

9

1

2

1

2

3

4

Do not help pulling back-up

tongs. MAKE SURE Chain

Hand is out of the way.




MAKING A CONNECTION


2

10

10

11


table, drill collar clamp, and

slip handles.

ROTATING OUT WITH THE ROTARY TABLE - Unlatch

the lower tongs. Make the top tongs bite using the

proper tong handles while rotating out with the rotary.

AFTER ROTARY STOPS, and Back-Up Hand un-

latches lead tongs, remove lead tongs.

Hold tongs clear of the Kelly.

OR



tongs clear of Kelly.

AFTER KELLY STOPS TURNING, unlatch bottom

set of tongs.

Place the lead tongs on the drill collar in the Mouse

Hole.



Mouse Hole.

12

13

14

15

16

17


Make the lead tongs bite on the drill collar in the

Mouse Hole, using the proper tong handles, while the

Driller spins the Kelly.

After the Kelly stops, step back while the top tongs

are latched onto Kelly.

After the top tongs are on the Kelly, make the bottom

tongs bite.

Make the lead tongs bite as the connection is tight-

ened, using the proper tong handles.



handles.

Latch the lead tongs onto the drill collar in the Rotary

Table.

Dope the connection in the Rotary Table as the Driller

pulls the drill collar out of the Mouse Hole.

1

2

3

1

2

18

19

20




MAKING A CONNECTION

3

After Back-Up Hand unlatches lead tongs, chain lead

tongs to A-leg.


the drill collar in the Rotary table.

Make the lead tongs bite on the drill collar in the

Rotary Table, using the proper tong handles, while the

Driller spins the Kelly and drill collar.

AFTER THE KELLY STOPS SPINNING, STAND CLEAR

while the top tongs are latched onto the drill collar.

After the top set of tongs are latched, make the lead

tongs bite using the proper tong handles, while the

connection is tightened.



handles.


rotary table.

Assist in removing the drill collar clamp by holding

proper handles as clamp is loosened and pin is

removed.

Remove clamp from drill collar and place in proper

location.

Assist in pulling the slips using proper lifting tech-

niques.


instructions.

END OF PROCEDURE

21

22

23

24

25

26

27

28

29

30


MAKING A

CONNECTION

MAKING A

CONNECTION

Floorman -

Lead Tong

Floorman -

Lead Tong

SPIN

NIN

G C

HA

IN

DR

IL

L P

IP

E

SPINNING CHAIN

DRILL PIPE

SPINNING CHAIN

DRILL PIPE

5. Making A Connection - EDC Romfor A Connection.pdfBroken Cable, Shackles Bolts, Inserts, Keepers,...

Documents

Transcript of 5. Making A Connection - EDC Romfor A Connection.pdfBroken Cable, Shackles Bolts, Inserts, Keepers,...