5 Logic Module Tunable Color Linear LED Arrays (LTM2) 24V DC … · 2020-06-18 · Color...

araya®

5 Logic Module

Tunable Color Linear LED Arrays (LTM2)24V DC Input (Constant Voltage)1000 Typical Peak Lumens / Foot

Data Sheet

ii | araya®5 Logic Modules with Tunable Color Linear LED Arrays

1000 Lumens / Footaraya®

5 Logic Module (24V DC)Tunable Color Linear LED Arrays

LTM2

Revised 3.20.20 | Specifications subject to change without notice

TABLE OF CONTENTS

1 Description and Key Features

2 Ordering Information

3 Electrical Specifications and Power Supplies

4 Mechanical Specifications

5 DMX512-A Control Card

6 Lutron® Control Card

7 Legrand Wattstopper DLM — LMLM Module

8 DALI Type 8 Control Card

9 Reflector End Caps

10 Case Temperature Measurement Points

11 Identifying ALM / Linear Array “Matched Sets”

12 Ribbon Cable Assemblies

13 Power / Control Cable Assemblies

14 Wiring Diagrams

15 Pre-Installation Notes

16 Typical Linear Array Configurations

Lumenetix, araya5, and Dynamic Dimming are registered trademarks of Lumenetix, Inc. © Lumenetix, Inc. 2020.

Lumenetix Inc. • 4742 Scotts Valley Dr. • Scotts Valley, CA 95066 • 877.805.7284 • www.erp-power.com • [email protected]

UL Recognized Component Dry or Damp Locations

Class 2 Input

UL Recognized ComponentDry or Damp Locations Class 2 Input


Class 2 Input

3 | araya®5 Logic Modules with Tunable Color Linear LED Arrays



LTM2


Descriptionaraya5 Logic Modules (ALM) connect to tunable color mid-power linear LED arrays that mix five colors of LEDs to deliver tunable and dimmable white light at 90+ CRI* with color consistency of <2 step MacAdam ellipse (SDCM) across a tuning range of 1650 - 8000K. The ALM is connected to one or more LED arrays via low-cost ribbon cables, and features on-board driver electronics and the araya5 control logic for precise control of LED light output while tuning and dimming. On board closed loop thermal feedback compensates each color channel for thermally induced variations in light output due to dimming or changes in ambient temperatures. On-board closed loop optical feedback measures the lumen depreciation of each channel and re-balances the color model to ensure color consistency over the 50,000 hour life of the LED array. A patented in-line manufacturing process captures and stores the spectral characteristics of each LED on the array, rapidly generating a unique color model for each array. Delivered light can be dimmed from 100 - 0.1%** at constant CCT. Gradients of saturated colors from 1 - 100% can be added to color points within the tuning range. The Zhaga-compliant LED arrays are compatible with traditional 0 - 10V wired controls, and feature on-board Bluetooth Low Energy (BLE) for commissioning. The arrays can access DMX512-A-RDM, Legrand Wattstopper’s Digital Light Management (DLM) control interface, DALI Type 8 or Lutron

® EcoSystem inputs via an optional

control card that connects to an electrically isolated expansion port within the ALM. For simple deployment, scene set allows up to five scenes to be pre-programmed into the LED array during production and recalled at the venue using a 0 - 10V recommended dimmer or via Bluetooth. Commissioning of the LED array and the re-programming of scenes is done via the wireless araya5 Tunable Color 2.0 iOS app that connects to the embedded Bluetooth radio.

Key Features• Tunable range: 1650 - 8000K

• 90+ CRI*• Dimmable from 100 - 0.1%** at constant CCT• Color gamut control: gradients of saturated colors from

1 - 100% can be added to color points• Integrated driver electronics and araya5 logic• On board thermal and optical feedback for color

consistency of <2 step MacAdam ellipse over 50,000 hour life

• In-line spectral capture and storage creates an unique color model for each Zhaga-compliant LED array, resulting in consistent CRI and CCT across all arrays

1 DESCRIPTION & KEY FEATURES

araya5 Tunable Color 2.0 iOS App

2016 IES PROGRESS REPORT SELECTION • 2016 LFI INNOVATION AWARDS CATEGORY WINNER • 2016 LUX AWARDS HIGHLY COMMENDED • 2016 EDISON REPORT TOP TEN MUST SEE LIST

• On-board thermal turndown• Compatible with 0 - 10V wired controls• On-board Bluetooth Low Energy (BLE) for commissioning• DMX512-A-RDM, Wattstopper DLM, DALI Type 8 or Lutron

EcoSystem control accessibility via an optional control card that connects to an electrically isolated compartment within the ALM

• Scene set enables up to five scenes to be preprogrammed and recalled using a 0 - 10V recommended dimmer or via Bluetooth

• DMX slots set by RDM or via wireless araya5 Tunable Color 2.0 iOS app

araya®5 Logic Modulesaraya

®5 Tunable Color Linear LED Arrays




LTM2


2 ORDERING INFORMATION

Photometrics and Ordering Codes (Linear LED Array Kits)1

Tunable Range

Typical Peak Lumens

Nominal LengthNominal Wattage

(±10%)Connectors

LocationOrdering Code

Specifications2 1650 - 8000K

8000 88 inches (4 x 22 in.) 80WBottom

80.001.097.03**

80.001.097.01***

Top 80.001.105.01***

7000 77 inches (1 x 11 in. + 3 x 22 in.) 70WBottom

80.001.096.03**

80.001.096.01***

Top 80.001.104.01***


80.001.095.03**

80.001.095.01***

Top 80.001.103.01***

5000 55 inches (1 x 11 in. + 2 x 22 in.) 50WBottom

80.001.094.03**

80.001.094.01***

Top 80.001.102.01***

4000 48 inches (2 x 24 in.) 40W Bottom80.001.200.03**

80.001.200.01***


80.001.093.03**

80.001.093.01***

Top 80.001.101.01***

3000 33 inches (1 x 11 in. + 1 x 22 in.) 30WBottom 80.001.092.01***

Top 80.001.100.01***

2000 24 inches (1 x 24 in.) 20W Bottom 80.001.201.01***


80.001.091.03**

80.001.091.01***

Top 80.001.099.01***


80.001.090.03**

80.001.090.01***

Top 80.001.098.01***

CRI (Ra) Across Tuning Range >90*

Dimming 100% to 0.1%**

Nominal Color Consistency <2 step MacAdam ellipse (±0.002 Duv from ANSI C78.377-2008 curve)*

Color Consistency Over Life Calibration maintains original color points over life*

Lumen Maintenance L70 (70% of initial lumens) at 50,000 hours

1. Kit includes linear LED array and araya5 Logic Module with on-board 0-10V and BT LE, as a factory pre-matched set which MUST be kept that way during installation for proper operation and control and CANNOT be

separated. It does not include ribbon cables, cable assemblies, reflector end caps or control cards (see below for accessory ordering specifications).

2. Specifications are within +/- 10% of the nominal value. Peak efficacy is not necessarily at typical peak lumens.

*From 2000 - 6000K, down to 5% dim level.

** 100 - 0.1% dimming is available for the indicated arrays when connected to 0.1% dimming-capable DIGITAL controls.

***100 - 1% dimming is available for the indicated arrays with analog 0 - 10V control, and with all other control protocols.




LTM2


2 ORDERING INFORMATION

Accessories for Linear LED Array Kits (Ordered Separately)Quantity Description Ordering Code

1 8” long flat ribbon cable; 16-pin Tyco connectors at each end (for connecting 1 ft. linear boards to each other) 28.031.001.04

1 24” long flat ribbon cable; 16-pin Tyco connectors at each end (for connecting ALM to one linear boards) 28.030.002.02

1 32” long flat ribbon cable; 16-pin Tyco connectors at 0”, 24” and 32” (for connecting ALM to two linear boards) 28.031.001.01

1 44” long flat ribbon cable; 16-pin Tyco connectors at -20”, -12”, 0”, and 24” (for connecting ALM to three linear boards) 28.031.001.02

1 68” long flat ribbon cable; 16-pin Tyco connectors at -34”, -26”, 0”, 26” and 34” (for connecting ALM to four linear boards) 28.031.001.03

1 24” long 2-wire ALM power cable assembly 28.030.001.01

1 24” long 7-wire ALM control cable assembly 28.002.002.01

1 DMX512-A-RDM Control Card*** 80.003.002.01

1 Lutron® Control Card*** 80.003.002.02

1 DALI Control Card*** 80.003.004.01

1 Legrand Wattstopper DLM - LMLM Module*** 80.003.003.03

Set of 2 Reflector end caps 45.001.011.01

***Control cards are shipped pre-attached to the ALM, & cannot be shipped individually. Control cards for different controls should NOT be interchanged in the field. This will void the Lumenetix warranty.




LTM2


3 ELECTRICAL SPECIFICATIONS

3.1 Electrical Specifications (araya®5 LOGIC MODULE)

Input Voltage 24V DC (Constant Voltage)

Nominal Power Input* 30W, 40W, 60W, and 80W

Nominal Current Input 1.25A (30W); 1.7A (40W); 2.5A (60W); 3.3A (80W)

Power Supply Classification Class 2 (UP TO 100W RATED POWER)

Power and Control Connector Power Connector: Molex 5023520200; Control Connector: Molex 874380743

Ribbon Cable Connector (supplied by third parties) TE Micro-Match 215460-4 (requires TE mating connector 2-215083-0)

Control Options** 0 – 10V, DMX512-A-RDM, Wattstopper DLM, Lutron® EcoSystem, DALI Type 8

CCT and Dimming Control Connections Plug-in connector for 24 gauge leads

*araya5 Logic Module (ALM) power dissipation is up to 10% of total power dissipation. Therefore ALM must be provided with adequate heat sink capability when applicable.

**DMX512-A-RDM, Lutron EcoSystem, DALI Type 8 or Wattstopper Digital Light Management control compatibility requires optional control card.

3.1a Control Specifications

PROTOCOL 1DIMMING*

2CCT

3SAT

4HUE NOTES

DMX512-A-RDM 1 0.1% 2 1650 - 8000K 1 - 100% 1 - 60°1. Requires control card connected to ALM.2. May be limited to 1% dimming by controller; see

control system specification for details.

0 - 10V ~1% 3 1650 - 8000K ** ** 3. 1 - 10V signal dims module to approximately 1%. In-line power relay required to achieve 0% output.

LUTRON ECOSYSTEM 4 0.1% 5 1650 - 8000K4. Requires control card connected to ALM.5. May be limited to 1% dimming by controller; see


DALI TYPE 8 6 0.1% 6. Requires control card connected to ALM.

WATTSTOPPER DLM 7 0.1% 8 1650 - 8000K7. Requires control card connected to ALM.8. May be limited to 1% dimming by controller; see


*100 - 0.1% dimming is available when connected to 0.1% dimming-capable digital controls.

100 - 1% dimming is available with analog 0 - 10V control.

** Two 0-10V lines can be used to control DIM and CCT independently, or program Scenes — in any combination of DIM, CCT, HUE and SAT — and recall them with five 0-10V presets.




LTM2


3 ELECTRICAL SPECIFICATIONS

3.2 Recommended Power Supplies (Constant Voltage)

Manufacturer Part NumberRated Power

1’ array (10W)

2’ array (20W)

3’ array (30W)

4’ array (40W)

5’ array (50W)

6’ array (60W)

7’ array (70W)

8’ array (80W)

ERP VLM40W-24 60W P P P

Amperor ANP101-24P1-277-2500L-1-P 60W P P P P P

ERP VLM60W-24 60W P P P P P

Hatch LV60-24N-UNV-I 60W P P P P

Mean Well IRM-60-24ST 60W P P P P

Efore / Roal Strato RSLP070-24 72W P P P P

Mean Well LPF-90-24 90W P P P P P P P P

Amperor ANP101-24P1-277-4160L-1 96W P P P P P P P P

DELTA Electronics LNE-24V100WDA 96W P P P P P P P P

ERP VLM100W-24 96W P P P P P P P P

Osram OT96W/24/UNV 96W P P P P P P P P

Tridonic LCU 96W 24V SR TOP 96W P P P P P P P P

AC Electronics AC-A100V24H4.1 100W P P P P P P P P

Philips Advance LEDINTA0024V41F0 100W P P P P

Mean Well HLG-120H-24A 120W P* P* P* P* P* P* P* P*

Excelsys LXV150-024SW 150W P* P* P* P* P* P* P* P*

Mean Well HLG-480H-24A 480W P* P* P* P* P* P* P* P*

IMPORTANT

The araya5 Logic Module (ALM) has on-board drive electronics, including dimming. A dimming driver should NOT be used.

CAUTION:• Using a constant current power supply will damage the module, and will void the Lumenetix warranty.• Using a triac or dimming driver will damage the module, and will void the Lumenetix warranty.• The power supply MUST be evaluated with the module(s) that it will be operated with.• If a recommended power supply from the above list is not used, it will void the Lumenetix warranty.• If unqualified power supplies are used in a fixture, it will void the Lumenetix warranty.• It is the responsibility of the fixture manufacturer to ensure that the power supply performance does not change over time. The Lumenetix

warranty is void if problems occur as a result of such changes.

*U.L. CLASS 1 — NON-NORTH AMERICA ONLY. NOTES:

• Recommendations are subject to change. Consult your Lumenetix representative for the most updated list.• Please contact the power supply manufacturer to verify that the current version of the listed power supply still meets the latest Lumenetix

testing approvals / qualifications.• Power supply qualification process:: if a power supply that is not part of the above list is submitted for testing to Lumenetix (during the

design-in phase), it will be qualified or disqualified within two weeks of submission.




LTM2


4 MECHANICAL SPECIFICATIONS

4.1.1 Linear LED Arrays

Array Dimensions (W x L)

Nominal 88 inches array (4 x 22 in. boards) W = 24 mm; L = 2240 mm

Nominal 77 inches array (1 x 11 in. + 3 x 22 in. boards) W = 24 mm; L = 1960 mm









Standard linear arrays are made up of a combination of 11 in. and 22 in. boards as per above. Other requested board lengths may be available.

araya5 Linear LED Board (2000 lumens; 22 inches Nominal Length)All dimensions are in millimeters. Linear board is shown with downward-facing connector on the bottom.

10X 4.30 THRU4X 2 THRU

1.76 6.66 TYP

0 4X 2.80

2X 8 12 TYP 2X 16

6X 21.20 24

0

1.7

6

2X

6.50

1

5

77.

50

140

202

.50

265

295

357

.50

420

482

.50

545

2

X 55

3.50

5

60

10X 8 KEEP OUT

3.6

1

THERMAL SENSORTHERMAL SENSOR

0

1.80 2.65 TYP

2X 5.05

0

537

.62

16.

34

38.

59

526

.50

548

.75

27.

46

3.56

0.20

12

34

REVISIONS

REV. DESCRIPTION DATE APPROVED

A PRODUCITON RELEASE 11/08/2016 A.N.

B ADDED INSULATOR PAD 1/9/2017 A.N.

ITEM NO. PART NUMBER QTY.1 22.700.022.01 1 PCBA 2 FOOT LUMENETIX 1

2 lumileds 3535L 843 462.038 16 PIN CONNECTOR 8-188275-6 24 67.700.002.02 B LTM2 INSULATOR PAD 2FT LX 1

D

C

B

AA

B

C

D

12345678

8 7 6 5 4 3 2 1

THE INFORMATION CONTAINED IN THISDRAWING IS THE SOLE PROPERTY OFLUMENETIX. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF LUMENETIX IS PROHIBITED.

PROPRIETARY AND CONFIDENTIAL

NEXT ASSY USED ON

APPLICATION

DIMENSIONS ARE IN MILLIMETERSTOLERANCES:ANGULAR: MACH 0.5LINEAR TOLERANCES UNLESSOTHER WISE SPECIFIED 0.15

INTERPRET GEOMETRICTOLERANCING PER: ASME Y14.5

MATERIAL

FINISH

DRAWN

CHECKED

ENG APPR.

MFG APPR.

Q.A.

COMMENTS:

DATENAME LumenetixTITLE:

SIZE

BDWG. NO. REV

WEIGHT: SCALE: 1:4

UNLESS OTHERWISE SPECIFIED:

B

A.N. 11/08/16

PCBA 2 FOOT LUMENETIXBOTTOM CONNECTOR

SHEET 1 OF 1

24.700.022.01DO NOT SCALE DRAWING

NOTES:

PCBA COLOR: TAIYO PSR-4000 LEW1 "LED WHITE" OR LUMENETIX 1. APPROVED EQUIVALENT PER IPC-SM840.

2. RECOMMENDED MINIMUM CLEARANCE TO ALL CONNECTORS 5MM.

3. ALL EXPOSED PADS MUST BE INSULATED.

4. THERMAL MEASURE POINT ("Tc" POINT) ADJACENT TO THERMAL SENSORS.


1.76 6.66 TYP

0 4X 2.80

2X 8 12 TYP 2X 16

6X 21.20 24

0

1.7

6

2X

6.50

1

5

77.

50

140

202

.50

265

295

357

.50

420

482

.50

545

2

X 55

3.50

5

60

10X 8 KEEP OUT

3.6

1


0

1.80 2.65 TYP

2X 5.05

0

537

.62

16.

34

38.

59

526

.50

548

.75

27.

46

3.56

0.20

12

34

REVISIONS






D

C

B

AA

B

C

D

12345678

8 7 6 5 4 3 2 1



NEXT ASSY USED ON

APPLICATION



MATERIAL

FINISH

DRAWN

CHECKED

ENG APPR.

MFG APPR.

Q.A.

COMMENTS:


SIZE

BDWG. NO. REV

WEIGHT: SCALE: 1:4


B

A.N. 11/08/16


SHEET 1 OF 1


NOTES:






12X 4.30 THRU

7.23 TYP

0 4X 2.80 12 TYP

8X 21.20 24

0

38.

51

101

.01

163

.51

226

.01

288

.51

318

.51

381

.01

443

.51

506

.01

568

.51

607

.02

12X 8 KEEP OUT

0 1.60

2.45 TYP

2X 5.25

0

13.

88

36.

13

570

.89

593

.14

25

582

.02

25 2

3

26.645 13.706

REVISIONS



ITEM NO. PART NUMBER Default/QTY.

1 22.700.033.01 1 PCBA 2 FOOT LUMENETIX 12 lumileds 3535L 843 462.038 16 PIN CONNECTOR 8-188275-6 2

D

C

B

AA

B

C

D

12345678

8 7 6 5 4 3 2 1



NEXT ASSY USED ON

APPLICATION



MATERIAL

FINISH

DRAWN

CHECKED

ENG APPR.

MFG APPR.

Q.A.

COMMENTS:


SIZE

BDWG. NO. REV

WEIGHT: SCALE: 1:4


A

A.N. 10/05/17

PCBA 24 INCH BOTTOM CONNECTOR

SHEET 1 OF 1


NOTES:





12X 4.30 THRU

7.23 TYP

0 4X 2.80 12 TYP

8X 21.20 24

0

38.

51

101

.01

163

.51

226

.01

288

.51

318

.51

381

.01

443

.51

506

.01

568

.51

607

.02

12X 8 KEEP OUT

0 1.60

2.45 TYP

2X 5.25

0

13.

88

36.

13

570

.89

593

.14

25

582

.02

25 2

3

26.645 13.706

REVISIONS



ITEM NO. PART NUMBER Default/QTY.

1 22.700.033.01 1 PCBA 2 FOOT LUMENETIX 12 lumileds 3535L 843 462.038 16 PIN CONNECTOR 8-188275-6 2

D

C

B

AA

B

C

D

12345678

8 7 6 5 4 3 2 1



NEXT ASSY USED ON

APPLICATION



MATERIAL

FINISH

DRAWN

CHECKED

ENG APPR.

MFG APPR.

Q.A.

COMMENTS:


SIZE

BDWG. NO. REV

WEIGHT: SCALE: 1:4


A

A.N. 10/05/17

PCBA 24 INCH BOTTOM CONNECTOR

SHEET 1 OF 1


NOTES:








LTM2



4.1.1 Linear LED Arrays (continued)


5X 4.30 THRU ALL

4X 2 THRU ALL

0

3.3

3

15

77.

50

140

202

.50

265

280

0 2X 2.80

12 TYP

3X 21.20 24

2X 6.34

2X 16

2X

6.50

2X

273.

50

4.47

5X 8 KEEP OUT THERMAL SENSOR THERMAL SENSOR

0

1.80 2.65 TYP

2X 5.05

0

16.

33

38.

58

246

.50

268

.75

27.

46

257

.63

4

0.20

1

3

2

0 2X 1.97

2X 6.97 2X 4.47

4

REVISIONS


A PRODUCTIION RELEASE 11/02/2016 A.N.


ITEM NO. PART NUMBER QTY.

1 22.700.025.01 1 MLTM PCB 1 FT LUMENETIX 1

2 lumileds 3535L 423 462.038 16 PIN CONNECTOR 8-188275-6 2

4 67.700.002.01 B LTM2 INSULATOR PAD 1FT LX 1

D

C

B

AA

B

C

D

12345678

8 7 6 5 4 3 2 1



NEXT ASSY USED ON

APPLICATION



MATERIAL

FINISH

DRAWN

CHECKED

ENG APPR.

MFG APPR.

Q.A.

COMMENTS:


SIZE

BDWG. NO. REV

WEIGHT: SCALE: 1:2


A.N. 11/02/16

MLTM PCBA 1 FT LUMENETIX16 PIN BOTTOM CONNECTOR

SHEET 1 OF 1


B

NOTES:

1. PCBA COLOR: TAIYO PSR-4000 LEW1 "LED WHITE" OR LUMENETIX APPROVED EQUIVALENT PER IPC-SM840.

2. RECOMMENDED MINIMUM CLEARANCE TO ALL CONNECTORS = 5MM.


4. THERMAL MEASURE POINT ("Tc" POINT) ADJACENT TO THERMAL SENSOR.

5X 4.30 THRU ALL

4X 2 THRU ALL

0

3.3

3

15

77.

50

140

202

.50

265

280

0 2X 2.80

12 TYP

3X 21.20 24

2X 6.34

2X 16

2X

6.50

2X

273.

50

4.47


0

1.80 2.65 TYP

2X 5.05

0

16.

33

38.

58

246

.50

268

.75

27.

46

257

.63

4

0.20

1

3

2

0 2X 1.97

2X 6.97 2X 4.47

4

REVISIONS








D

C

B

AA

B

C

D

12345678

8 7 6 5 4 3 2 1



NEXT ASSY USED ON

APPLICATION



MATERIAL

FINISH

DRAWN

CHECKED

ENG APPR.

MFG APPR.

Q.A.

COMMENTS:


SIZE

BDWG. NO. REV

WEIGHT: SCALE: 1:2


A.N. 11/02/16


SHEET 1 OF 1


B

NOTES:








LTM2



araya5 Thermal Pad for Linear LED Board (2 ft. Nominal Length)All dimensions are in millimeters.

araya5 Thermal Pad for Linear LED Board (1 ft. Nominal Length)All dimensions are in millimeters.

4.1.2 Heat Sinking / Electrical Insulation of LTM2 BoardsTo ensure proper electrical insulation between the linear arrays and heat sink, the linear arrays are provided with a pre-applied double sided adhesive

insulating tape. This thermal pad insulates electrically while also allowing the heat to flow from the LED board to the luminaire’s heat sink.

Be sure to remove the plastic liner before attaching the linear array to the heat sink.

10X 6

0 4X 2.80

2X 9 6X 21.20

24

0

9.5

0 15

40.

50

77.

50

140

202

.50

265

295

357

.50

420

482

.50

519

.50 545

550

.75

560

4X R 1 MAX

0.203

REVISIONS


A PRODUCTION RELEASE 11/22/2016 A.N.

B MADE CONNECTOR CUTOUTS SYMMETRICAL 4/21/2017 A.N.

D

C

B

AA

B

C

D

12345678

8 7 6 5 4 3 2 1



NEXT ASSY USED ON

APPLICATION



MATERIAL

FINISH

XBQ-BP20N

DRAWN

CHECKED

ENG APPR.

MFG APPR.

Q.A.

COMMENTS:


SIZE

BDWG. NO. REV

WEIGHT: SCALE: 1:4


B

A.N. 11/22/16

LTM2 INSULATOR PAD 2FT LX

SHEET 1 OF 1DO NOT SCALE DRAWING

5X 6

0

40.

50

15

9.2

5

77.

50

140

202

.50

239

.50

270

.75 265

280

0 2X 2.80

3X 21.20

2X 9

24

4X R 1 MAX

0.203 THK

REVISIONS



B MADE CONNECTOR CUTOUTS SYMMETRICAL 4/21/2017 A.N.

D

C

B

AA

B

C

D

12345678

8 7 6 5 4 3 2 1



NEXT ASSY USED ON

APPLICATION



MATERIAL

FINISH

XBQ-BP20N

DRAWN

CHECKED

ENG APPR.

MFG APPR.

Q.A.

COMMENTS:


SIZE

BDWG. NO. REV

WEIGHT: SCALE: 1:2


B

A.N. 11/22/16

LTM2 INSULATOR PAD 1FT LX

SHEET 1 OF 1





LTM2



Connector Cutouts / Hole Patterns for Linear LED Board (2 ft. Nominal Length)All dimensions outside parentheses are in millimeters. All dimensions within parentheses are in inches.

4.1.3 Connector Cutouts / Hole Patterns for 2 Ft. Linear Array Fixture DesignsLeave adequate clearance around the ribbon cable connector so that it does not come in contact with the fixture’s metal edge.

8X R3.18.125

10X M3X0.5 OR #4 OR #6 TAPPED HOLE

0

.000

13.

83.5

45

41

.08

1.61

8

51

4.50

20.2

56

55

1.25

21.7

03

56

022

.047

0.000

2X 13.58.535

2X 25.481.003

15 .591

77

.50

3.05

1

14

05.

512

202

.50

7.97

2

26

510

.433

29

511

.614

35

7.50

14.0

75

42

016

.535

48

2.50

18.9

96

54

521

.457

6X 2.80.110

4X 21.20.835

ALL DIMENSIONS FOR HOLES/CUT-OUTSARE FROM THIS POINT

TOP DOWN VIEW (LINEAR ARRAY IS FACING UP, FIXTURE ONLY)

TOP DOWN VIEW (LINEAR ARRAY IS FACING UP, FIXTURE WITH PCBA ON TOP)

ALL DIMENSIONSFORHOLES/CUT-OUTSARE FROM THIS POINT

ALL DIMENSIONS FROM THIS POINT

REVISIONS


1 ENGINEERING SKETCH 8/25/2017 A.N.

2 ADDED 10X THREADED HOLES 9/1/2017 A.N.

D

C

B

AA

B

C

D

12345678

8 7 6 5 4 3 2 1



NEXT ASSY USED ON

APPLICATION



MATERIAL

FINISH

DRAWN

CHECKED

ENG APPR.

MFG APPR.

Q.A.

COMMENTS:


SIZE

BDWG. NO. REV

WEIGHT: SCALE: 1:5


2

A.N. 8.18.17

FIXTURE CUTOUTS FOR ARAYA AND BLANCO 2 FT

SHEET 1 OF 1

TBDDO NOT SCALE DRAWING

8X R3.18.125

10X M3X0.5 OR #4 OR #6 TAPPED HOLE

0

.000

13.

83.5

45

41

.08

1.61

8

51

4.50

20.2

56

55

1.25

21.7

03

56

022

.047

0.000

2X 13.58.535

2X 25.481.003

15 .591

77

.50

3.05

1

14

05.

512

202

.50

7.97

2

26

510

.433

29

511

.614

35

7.50

14.0

75

42

016

.535

48

2.50

18.9

96

54

521

.457

6X 2.80.110

4X 21.20.835




ALL DIMENSIONSFORHOLES/CUT-OUTSARE FROM THIS POINT

ALL DIMENSIONS FROM THIS POINT

REVISIONS



2 ADDED 10X THREADED HOLES 9/1/2017 A.N.

D

C

B

AA

B

C

D

12345678

8 7 6 5 4 3 2 1



NEXT ASSY USED ON

APPLICATION



MATERIAL

FINISH

DRAWN

CHECKED

ENG APPR.

MFG APPR.

Q.A.

COMMENTS:


SIZE

BDWG. NO. REV

WEIGHT: SCALE: 1:5


2

A.N. 8.18.17


SHEET 1 OF 1





LTM2



Connector Cutouts / Hole Patterns for Linear LED Board (1 ft. Nominal Length)All dimensions outside parentheses are in millimeters. All dimensions within parentheses are in inches.

4.1.4 Connector Cutouts / Hole Patterns for 1 Ft. Linear Array Fixture DesignsLeave adequate clearance around the ribbon cable connector so that it does not come in contact with the fixture’s metal edge.

0.000

2.80.110

2X 13.54.533

2X 21.20.835

2X 25.521.005

0

.000

13.

79.5

43

15 .591

41

.12

1.61

9

77

.50

3.05

1

14

05.

512

202

.50

7.97

2

239

.50

9.42

9

26

510

.433

27

1.29

10.6

81

28

011

.024






REVISIONS



D

C

B

AA

B

C

D

12345678

8 7 6 5 4 3 2 1



NEXT ASSY USED ON

APPLICATION



MATERIAL

FINISH

DRAWN

CHECKED

ENG APPR.

MFG APPR.

Q.A.

COMMENTS:


SIZE

BDWG. NO. REV

WEIGHT: SCALE: 1:2


1

A.N. 9/7/17


SHEET 1 OF 1


0.000

2.80.110

2X 13.54.533

2X 21.20.835

2X 25.521.005

0

.000

13.

79.5

43

15 .591

41

.12

1.61

9

77

.50

3.05

1

14

05.

512

202

.50

7.97

2

239

.50

9.42

9

26

510

.433

27

1.29

10.6

81

28

011

.024






REVISIONS



D

C

B

AA

B

C

D

12345678

8 7 6 5 4 3 2 1



NEXT ASSY USED ON

APPLICATION



MATERIAL

FINISH

DRAWN

CHECKED

ENG APPR.

MFG APPR.

Q.A.

COMMENTS:


SIZE

BDWG. NO. REV

WEIGHT: SCALE: 1:2


1

A.N. 9/7/17


SHEET 1 OF 1





LTM2



4.2 araya5 Logic Module

ALM Dimensions (H x W x L) H = 15.11 mm (0.60 in.); W = 30 mm (1.18 in.); L = 133 mm (5.24 in)

Dimensions provided are for the ALM without optional control cards.

araya5 Logic ModuleAll dimensions are in millimeters. The mounting holes are 5 mm in diameter.

2X 5 THRU ALL

0

2X

14

24.

22

99.

28

6

127

133

0

2X 9

2X 15

2X 21

30

0

3

10.61

15.11

D

C

B

AA

B

C

D

12345678

8 7 6 5 4 3 2 1



NEXT ASSY USED ON

APPLICATION



MATERIAL

FINISH

DRAWN

CHECKED

ENG APPR.

MFG APPR.

Q.A.

COMMENTS:


SIZE

BDWG. NO. REV

WEIGHT: SCALE: 1:1


1

A.N. 01/12/16

ALM ASSEMBLY

SHEET 1 OF 1

---DO NOT SCALE DRAWING




LTM2


5.1 araya5 Logic Module with DMX512-A-RDM Control Card (PHOENIX CONNECTORS) - OLD

ALM Dimensions (H x W x L) H = 18.13 mm (0.71 in.); W = 30 mm (1.18 in.); L = 133 mm (5.24 in.)

5.1a Mechanical Specifications – DMX512-A-RDM Control Card (PHOENIX CONNECTORS) - OLD

DMX Control CardAll dimensionss are in millimeters.

2X 4.30

0

2.5

0

15.

20

19

49

52.

80

65.

50

68

0

4.50 2X 6.50

2X 18.50 20.50

25

0

1.6

0 6

.07

2.2

0 23

12.30

REVISIONS



D

C

B

AA

B

C

D

12345678

8 7 6 5 4 3 2 1



NEXT ASSY USED ON

APPLICATION



MATERIAL

FINISH

DRAWN

CHECKED

ENG APPR.

MFG APPR.

Q.A.

COMMENTS:


SIZE

BDWG. NO. REV

WEIGHT: SCALE: 2:1


A

A.N. 8/5/16

DB ASSEMBLY

SHEET 1 OF 1


2X 4.30

0

2.5

0

15.

20

19

49

52.

80

65.

50

68

0

4.50 2X 6.50

2X 18.50 20.50

25

0

1.6

0 6

.07

2.2

0 23

12.30

REVISIONS



D

C

B

AA

B

C

D

12345678

8 7 6 5 4 3 2 1



NEXT ASSY USED ON

APPLICATION



MATERIAL

FINISH

DRAWN

CHECKED

ENG APPR.

MFG APPR.

Q.A.

COMMENTS:


SIZE

BDWG. NO. REV

WEIGHT: SCALE: 2:1


A

A.N. 8/5/16

DB ASSEMBLY

SHEET 1 OF 1


5 DMX512-A CONTROL CARD

Lumenetix part #: 80.003.001.01

Wire Specifications: 22-24 AWG, stranded tinned copper (TC) only

Connector: Phoenix Contact 1771033

araya5 Logic Module with DMX Control Card and CoverDimensions outside parentheses are in millimeters. Dimensions within parentheses are in inches.The mounting holes are 5 mm in diameter.

2X 5 THRU ALL

0 .00 6 .24

2X

14 .55

24.

75.9

7

28.

881.

14

94.

623.

73

98.

753.

89

2X

119

4.69

127

5.00

133

5.24

0.00

2X 9.35

15.59

21.83

301.18

0.00

3.12

2X 15.01.59

18.13.71

D

C

B

AA

B

C

D

12345678

8 7 6 5 4 3 2 1



NEXT ASSY USED ON

APPLICATION



MATERIAL

FINISH

DRAWN

CHECKED

ENG APPR.

MFG APPR.

Q.A.

COMMENTS:


SIZE

BDWG. NO. REV

WEIGHT: SCALE: 1:1


1

A.N. 01/12/16

ALM ASSEMBLY

SHEET 3 OF 3


DISCONTI

NUED -

NO LONGER

AVAILA

BLE




LTM2


5.1b Mounting Specifications – DMX Control Card (PHOENIX CONNECTORS) - OLD

The Control Card is mounted on the 10-pin header and located on the two bosses, and then captured in place to the ALM with two (2) self-tapping screws.

Screw Specifications: Phillips Rounded Head Thread-Forming Screws for Plastic, 18-8 Stainless Steel, Number 4 Size, 1/8" Long; McMasterCarr # 99461A105.

Torque Specifications: 2.0 to 2.5 in-lb

CAUTION: The screws are very small and are self-threaded into small plastic bosses. Overtorquing will strip the plastic and damage the ALM housing.


DISCONTI

NUED -

NO LONGER

AVAILA

BLE




LTM2



5.2 araya5 Logic Module with DMX512-A-RDM Control Card (WAGO CONNECTORS)


araya5 Logic Module with DMX Control Card and CoverDimensions outside parentheses are in millimeters. Dimensions within parentheses are in inches.The mounting holes are 5 mm in diameter.

5.2a Mechanical Specifications – DMX512-A-RDM Control Card (WAGO CONNECTORS)

DMX Control CardAll dimensionss are in millimeters.


Wire Specifications: 22-24 AWG, stranded tinned copper (TC) only

Connector: Wago 805

2X 5 THRU ALL

0 .00

6 .24

2X

14 .55

24.

75.9

7

28.

881.

14

94.

623.

73

98.

753.

89

2X

119

4.69

12

75.

00

13

35.

24

0.00

2X 9.35

15.59

21.83

301.18

0.00

3.12

2X 15.01.59

23.61.93

D

C

B

AA

B

C

D

12345678

8 7 6 5 4 3 2 1



NEXT ASSY USED ON

APPLICATION



MATERIAL

FINISH

DRAWN

CHECKED

ENG APPR.

MFG APPR.

Q.A.

COMMENTS:


SIZE

BDWG. NO. REV

WEIGHT: SCALE: 1:1


1

A.N. 01/12/16

ALM ASSEMBLY

SHEET 3 OF 3


0

2.2

0

4.3

6

12.

07

0

2.6

7

16.

27

19

49

51.

73

65.

33

68

0

4.50 2X 6.80

2X 18.80 20.50

25

23 12.30

D

C

B

AA

B

C

D

12345678

8 7 6 5 4 3 2 1



NEXT ASSY USED ON

APPLICATION



MATERIAL

FINISH

DRAWN

CHECKED

ENG APPR.

MFG APPR.

Q.A.

COMMENTS:


SIZE

BDWG. NO. REV

WEIGHT: SCALE: 2:1


1

A.N. 01/12/16

ALM ASSEMBLY

SHEET 1 OF 1





LTM2



5.2b Mounting Specifications – DMX Control Card (WAGO CONNECTORS)








LTM2


6.1 araya5 Logic Module with Lutron® EcoSystem Control Card


araya5 Logic Module with Lutron Control Card and CoverDimensions outside parentheses are in millimeters. Dimensions within parentheses are in inches.The mounting holes are 5 mm in diameter.

6.2 Mechanical Specifications (Lutron EcoSystem Control Card)

Lutron Control CardAll dimensionss are in millimeters.

6 LUTRON CONTROL CARD


2X 4.30 0

19

49

53.

62

66.

32

68

0

4.50

9.85

17.85 20.50

25

0

1.6

0

6.4

0

23

12.30

REVISIONS



D

C

B

AA

B

C

D

12345678

8 7 6 5 4 3 2 1



NEXT ASSY USED ON

APPLICATION



MATERIAL

FINISH

DRAWN

CHECKED

ENG APPR.

MFG APPR.

Q.A.

COMMENTS:


SIZE

BDWG. NO. REV

WEIGHT: SCALE: 2:1


A

A.N. 10/5/16

PCBA DB LUTRON ECOSYSTEMS

SHEET 1 OF 1

24.030.005.01 DO NOT SCALE DRAWING

2X 4.30 0

19

49

53.

62

66.

32

68

0

4.50

9.85

17.85 20.50

25

0

1.6

0

6.4

0

23

12.30

REVISIONS



D

C

B

AA

B

C

D

12345678

8 7 6 5 4 3 2 1



NEXT ASSY USED ON

APPLICATION



MATERIAL

FINISH

DRAWN

CHECKED

ENG APPR.

MFG APPR.

Q.A.

COMMENTS:


SIZE

BDWG. NO. REV

WEIGHT: SCALE: 2:1


A

A.N. 10/5/16


SHEET 1 OF 1


2X 5 .20 THRU

0 .00

2X

14 .55

24.

20.9

5

98.

753.

89

2X

119

4.69

12

75.

00

13

35.

24

6 .24

0.00

9.35

15.59

301.18

0.00

3.12

15.03.59

20.53.81

D

C

B

AA

B

C

D

12345678

8 7 6 5 4 3 2 1



NEXT ASSY USED ON

APPLICATION



MATERIAL

FINISH

DRAWN

CHECKED

ENG APPR.

MFG APPR.

Q.A.

COMMENTS:


SIZE

BDWG. NO. REV

WEIGHT: SCALE: 1:1


1

A.N. 10/6/16

ALM ASSEMBLY LUTRON DB PROFILE


Wire Specifications: 18-22 AWG, solid wire or tin-dipped stranded

Connector: TE 2834006-2




LTM2


6 LUTRON CONTROL CARD





6.3 Mounting Specifications (Lutron® EcoSystem Control Card)




LTM2


7.1 araya5 Logic Module with Legrand Wattstopper’s DLM LMLM Module


araya5 Logic Module with LMLM Module and CoverDimensions outside parentheses are in millimeters. Dimensions within parentheses are in inches.The mounting holes are 5 mm in diameter.

7.2 Mechanical Specifications (LMLM Module)

Legrand Wattstopper DLM LMLM ModuleDimensions outside parentheses are in millimeters. Dimensions within parentheses are in inches.

Wire Specifications: Solid 20/3 AWG, red/blue/black


2X 5 0.20 THRU ALL

0 .00

2X

14 .55

24.

20.9

5

99.

303.

91

2X

119

4.69

12

75.

00

13

35.

24

6 .24

0.00

2X 9.35

15.59

21.83

301.18

0.00

3.12

15.03.59

2X 20.27.80

19.87.78

D

C

B

AA

B

C

D

12345678

8 7 6 5 4 3 2 1



NEXT ASSY USED ON

APPLICATION



MATERIAL

FINISH

DRAWN

CHECKED

ENG APPR.

MFG APPR.

Q.A.

COMMENTS:


SIZE

BDWG. NO. REV

WEIGHT: SCALE: 1:1


1

A.N. 01/12/16

ALM ASSEMBLY

SHEET 2 OF 2


.0

0 0

2.

0852

.80

2.

68 68

.000

.73

18.49

.266.49

.9825

2.

5865

.50

.0

0 0

.0

61.

57

.2

46.

06

.0

0 0

.9

022

.95

.000

.49

12.37

D

C

B

AA

B

C

D

12345678

8 7 6 5 4 3 2 1



NEXT ASSY USED ON

APPLICATION



MATERIAL

FINISH

DRAWN

CHECKED

ENG APPR.

MFG APPR.

Q.A.

COMMENTS:


SIZE

BDWG. NO. REV

WEIGHT: SCALE: 2:1



7 WATTSTOPPER DLM — LMLM MODULE





LTM2


The LMLM Module is mounted on the 10-pin header and located on the two bosses, and then captured in place to the ALM with two (2) self-tapping screws.




Please refer to the Legrand Wattstopper website for detailed specifications, wiring diagrams and installation instructions:https://www.legrand.us/categories/lightingcontrolsbuildingsystems/human-centric-lighting/led-light-engines.aspx

7 WATTSTOPPER DLM — LMLM MODULE

7.3 Mounting Specifications (LMLM Module)

https://www.legrand.us/categories/lightingcontrolsbuildingsystems/human-centric-lighting/led-light-engines.aspx




LTM2


8.1 araya5 Logic Module with DALI Type 8 Control Card


araya5 Logic Module with DALI Control Card and CoverDimensions outside parentheses are in millimeters. Dimensions within parentheses are in inches.The mounting holes are 5 mm in diameter.

8.2 Mechanical Specifications (DALI Type 8 Control Card)

DALI Control CardAll dimensionss are in millimeters.

8 DALI TYPE 8 CONTROL CARD


2X 4.30 0

19

49

53.

62

66.

32

68

0

4.50

9.85

17.85 20.50

25

0

1.6

0

6.4

0

23

12.30

REVISIONS



D

C

B

AA

B

C

D

12345678

8 7 6 5 4 3 2 1



NEXT ASSY USED ON

APPLICATION



MATERIAL

FINISH

DRAWN

CHECKED

ENG APPR.

MFG APPR.

Q.A.

COMMENTS:


SIZE

BDWG. NO. REV

WEIGHT: SCALE: 2:1


A

A.N. 10/5/16


SHEET 1 OF 1


2X 4.30 0

19

49

53.

62

66.

32

68

0

4.50

9.85

17.85 20.50

25

0

1.6

0

6.4

0

23

12.30

REVISIONS



D

C

B

AA

B

C

D

12345678

8 7 6 5 4 3 2 1



NEXT ASSY USED ON

APPLICATION



MATERIAL

FINISH

DRAWN

CHECKED

ENG APPR.

MFG APPR.

Q.A.

COMMENTS:


SIZE

BDWG. NO. REV

WEIGHT: SCALE: 2:1


A

A.N. 10/5/16


SHEET 1 OF 1


2X 5 .20 THRU

0 .00

2X

14 .55

24.

20.9

5

98.

753.

89

2X

119

4.69

12

75.

00

13

35.

24

6 .24

0.00

9.35

15.59

301.18

0.00

3.12

15.03.59

20.53.81

D

C

B

AA

B

C

D

12345678

8 7 6 5 4 3 2 1



NEXT ASSY USED ON

APPLICATION



MATERIAL

FINISH

DRAWN

CHECKED

ENG APPR.

MFG APPR.

Q.A.

COMMENTS:


SIZE

BDWG. NO. REV

WEIGHT: SCALE: 1:1


1

A.N. 10/6/16

ALM ASSEMBLY LUTRON DB PROFILE


Wire Specifications: 18-22 AWG, solid wire or tin-dipped stranded





LTM2


8 DALI TYPE 8 CONTROL CARD


Screw Specifications: Phillips Rounded Head Thread-Forming Screws for Plastic, 18-8 Stainless Steel, Number 4 Size, 1/8" Long;

McMasterCarr # 99461A105.



8.3 Mounting Specifications (DALI Type 8 Control Card)




LTM2


9 REFLECTOR END CAPS


Reflector End Caps (Set of 2) with Diffuser

1

2

3

REMOVE PLASTIC LINER

REVISIONS




1 64.018.001.01 C REFLECTOR MLTM TERM FLAT CONN SIDE 2

2 64.001.012.01 A END CAP DIFFUSER 2

3 67.700.001.01 A END CAP GASKET 2

4 930.026 ANTI-STAT. BAG 2 MIL 3x5 INCH RESEAL 1

5 LABEL, LUMENETIX, PART NUMBER DESCRIPTION, REVISION 1

D

C

B

AA

B

C

D

12345678

8 7 6 5 4 3 2 1



NEXT ASSY USED ON

APPLICATION



MATERIAL

FINISH

DRAWN

CHECKED

ENG APPR.

MFG APPR.

Q.A.

COMMENTS:


SIZE

BDWG. NO. REV

WEIGHT: SCALE: 4:1


A

A.N. 10/24/16

ASSY END CAP DIFFUSER

SHEET 1 OF 1


NOTES:

1. PRIOR TO ASSEMBLY REMOVE PLASTIC LINER.

2. BUILD ASSEMBLY AS SHOWN.

3. PLACE 2 END CAP ASSEMBLIES INTO PLASTIC BAG.

4. ADD LABEL TO THE OUTSIDE OF THE PLASTIC BAG.

NOTE: The reflector end caps are fastened to the fixture using 6mm - 8mm (M2.5 - M4) screws, which are inserted through the end caps and the hole in the LED PCB. The opposite side -- where it is not fastened -- must be used with double-sided tape.




LTM2


10 CASE TEMPERATURE MEASUREMENT POINTS

10.1 araya®5 Logic Module (ALM) Case Temperature (Tc) Measurement Points

10.2 Linear LED Array Case Temperature (Tc) Measurement Point

Tc Measurement Point is adjacent to Thermal Sensor.

MAXIMUM Tc FOR LINEAR LED ARRAY: 60°C

MAXIMUM CASE TEMPERATURE (Tc) FOR ALM: 70°C


1.76 6.66 TYP

0 4X 2.80

2X 8 12 TYP 2X 16

6X 21.20 24

0

1.7

6

2X

6.50

1

5

77.

50

140

202

.50

265

295

357

.50

420

482

.50

545

2

X 55

3.50

5

60

10X 8 KEEP OUT

3.6

1


0

1.80 2.65 TYP

2X 5.05

0

537

.62

16.

34

38.

59

526

.50

548

.75

27.

46

3.56

0.20

12

34

REVISIONS






D

C

B

AA

B

C

D

12345678

8 7 6 5 4 3 2 1



NEXT ASSY USED ON

APPLICATION



MATERIAL

FINISH

DRAWN

CHECKED

ENG APPR.

MFG APPR.

Q.A.

COMMENTS:


SIZE

BDWG. NO. REV

WEIGHT: SCALE: 1:4


B

A.N. 11/08/16


SHEET 1 OF 1


NOTES:






1.76 6.66 TYP

0 4X 2.80

2X 8 12 TYP 2X 16

6X 21.20 24

0

1.7

6

2X

6.50

1

5

77.

50

140

202

.50

265

295

357

.50

420

482

.50

545

2

X 55

3.50

5

60

10X 8 KEEP OUT

3.6

1


0

1.80 2.65 TYP

2X 5.05

0

537

.62

16.

34

38.

59

526

.50

548

.75

27.

46

3.56

0.20

12

34

REVISIONS






D

C

B

AA

B

C

D

12345678

8 7 6 5 4 3 2 1



NEXT ASSY USED ON

APPLICATION



MATERIAL

FINISH

DRAWN

CHECKED

ENG APPR.

MFG APPR.

Q.A.

COMMENTS:


SIZE

BDWG. NO. REV

WEIGHT: SCALE: 1:4


B

A.N. 11/08/16


SHEET 1 OF 1


NOTES:





5X 4.30 THRU ALL

4X 2 THRU ALL

0

3.3

3

15

77.

50

140

202

.50

265

280

0 2X 2.80

12 TYP

3X 21.20 24

2X 6.34

2X 16

2X

6.50

2X

273.

50

4.47


0

1.80 2.65 TYP

2X 5.05

0

16.

33

38.

58

246

.50

268

.75

27.

46

257

.63

4

0.20

1

3

2

0 2X 1.97

2X 6.97 2X 4.47

4

REVISIONS








D

C

B

AA

B

C

D

12345678

8 7 6 5 4 3 2 1



NEXT ASSY USED ON

APPLICATION



MATERIAL

FINISH

DRAWN

CHECKED

ENG APPR.

MFG APPR.

Q.A.

COMMENTS:


SIZE

BDWG. NO. REV

WEIGHT: SCALE: 1:2


A.N. 11/02/16


SHEET 1 OF 1


B

NOTES:





1’ Linear Array

2’ Linear Array

UL Recognized ComponentDry or Damp Locations Class 2 Input


Class 2 Input




LTM2


11 IDENTIFYING “MATCHED SETS”




LTM2


12 RIBBON CABLE ASSEMBLIES

12.1 Flat 16-Pin Ribbon Cable (Nominal 8” Length)


16-pin Tyco connectors at each end; for connecting 1 ft. linear boards to each other.

203 12.5

3 21

2X CUT CABLE FLUSH TO CONNECTOR +/- 0.5

RED WIRE IS PIN 1

REVISIONS




1 16 PIN RIBBON CABLE 3M 3365-16 12 LABEL, LUMENETIX, PART#, DESCRIPTION, REVISION 13 16 PIN CONNECTOR 1-215083-6 2

4

A

123

B B

A

2 134

DO NOT SCALE DRAWING SHEET 1 OF 1


SCALE: 1:2 WEIGHT:

REVDWG. NO.

BSIZE

TITLE:

NAME DATE

COMMENTS:

Q.A.

MFG APPR.

ENG APPR.

CHECKED

DRAWN

FINISH

MATERIAL

INTERPRET GEOMETRICTOLERANCING PER:

DIMENSIONS ARE IN MM

TOLERANCES:

ANGULAR: .5 ONE PLACE DECIMAL .24 TWO PLACE DECIMAL .12

APPLICATION

USED ONNEXT ASSY

PROPRIETARY AND CONFIDENTIALTHE INFORMATION CONTAINED IN THISDRAWING IS THE SOLE PROPERTY OF<INSERT COMPANY NAME HERE>. ANY REPRODUCTION IN PART OR AS A WHOLEWITHOUT THE WRITTEN PERMISSION OF<INSERT COMPANY NAME HERE> IS PROHIBITED.

SEE BOM

A.N.

12/02/16

ASSY CABLE ALM 16 (0, 8)

28.031.001.04 A

LUMENETIX, INCNOTES:

1. CONNECTOR COLOR: RED OR LUMENETIX ENGINEERING APPROVED COLOR.

2. BUILD CABLE ASSEMBLY AS SHOWN.

3. TEST CABLE ASSEMBLY FOR CONTINUITY.

203 12.5

3 21


RED WIRE IS PIN 1

REVISIONS




1 16 PIN RIBBON CABLE 3M 3365-16 12 LABEL, LUMENETIX, PART#, DESCRIPTION, REVISION 13 16 PIN CONNECTOR 1-215083-6 2

4

A

123

B B

A

2 134



SCALE: 1:2 WEIGHT:

REVDWG. NO.

BSIZE

TITLE:

NAME DATE

COMMENTS:

Q.A.

MFG APPR.

ENG APPR.

CHECKED

DRAWN

FINISH

MATERIAL



TOLERANCES:


APPLICATION

USED ONNEXT ASSY


SEE BOM

A.N.

12/02/16

ASSY CABLE ALM 16 (0, 8)

28.031.001.04 A





Note: All dimensions are in millimeters.




LTM2




16-pin Tyco connectors at each end; for connecting ALM to 1 linear board.


610 12.5

3 21


RED WIRE IS PIN 1

REVISIONS



ITEM NO. PART NUMBER DESCRIPTION QTY.

1 16 PIN RIBBON CABLE 3M 3365/16 PIN PVC RIBBON CABLE 12 LABEL LUMENETIX, P/N, DESCRIPTION, REVISION 13 16 PIN CONNECTOR c-1-215083-6-t-3d CONNECTOR 16 PIN 1-215083-6 2

4

A

123

B B

A

2 134



SCALE: 1:2 WEIGHT:

REVDWG. NO.

BSIZE

TITLE:

NAME DATE

COMMENTS:

Q.A.

MFG APPR.

ENG APPR.

CHECKED

DRAWN

FINISH

MATERIAL



TOLERANCES:


APPLICATION

USED ONNEXT ASSY


SEE BOM

A.N.

7/13/16

ASSY CABLE ALM16 (0,24)

28.030.002.02 A





610 12.5

3 21


RED WIRE IS PIN 1

REVISIONS





4

A

123

B B

A

2 134



SCALE: 1:2 WEIGHT:

REVDWG. NO.

BSIZE

TITLE:

NAME DATE

COMMENTS:

Q.A.

MFG APPR.

ENG APPR.

CHECKED

DRAWN

FINISH

MATERIAL



TOLERANCES:


APPLICATION

USED ONNEXT ASSY


SEE BOM

A.N.

7/13/16

ASSY CABLE ALM16 (0,24)

28.030.002.02 A









LTM2




16-pin Tyco connectors at at 0”, 24” and 32”; for connecting ALM to 2 linear boards.


813 15

610 13

3 21


RED WIRE IS PIN 1

REVISIONS





4

A

123

B B

A

2 134



SCALE: 1:2 WEIGHT:

REVDWG. NO.

BSIZE

TITLE:

NAME DATE

COMMENTS:

Q.A.

MFG APPR.

ENG APPR.

CHECKED

DRAWN

FINISH

MATERIAL



TOLERANCES:


APPLICATION

USED ONNEXT ASSY


SEE BOM

A.N.

7/13/16

ASSY CABLE ALM 16 (0,24, 32)

28.031.001.01 A





813 15

610 13

3 21


RED WIRE IS PIN 1

REVISIONS





4

A

123

B B

A

2 134



SCALE: 1:2 WEIGHT:

REVDWG. NO.

BSIZE

TITLE:

NAME DATE

COMMENTS:

Q.A.

MFG APPR.

ENG APPR.

CHECKED

DRAWN

FINISH

MATERIAL



TOLERANCES:


APPLICATION

USED ONNEXT ASSY


SEE BOM

A.N.

7/13/16

ASSY CABLE ALM 16 (0,24, 32)

28.031.001.01 A









LTM2




16-pin Tyco connectors at -20”, -12”, 0”, and 24”; for connecting ALM to 3 linear boards.

610 15

915 25

1118 30

2 13


RED WIRE IS PIN 1

REVISIONS



B CABLE LENGTH FROM 1422 TO 1118. TEST FOR SHORTS 9/12/2017 A.N.


1 LABEL, LUMENETIX, PART#, DESCRIPTION, REVISION 12 16 PIN CONNECTOR 1-215083-6 43 16 PIN RIBBON CABLE 3M 3365-16 1

4

A

123

B B

A

2 134



SCALE: 1:2 WEIGHT:

REVDWG. NO.

BSIZE

TITLE:

NAME DATE

COMMENTS:

Q.A.

MFG APPR.

ENG APPR.

CHECKED

DRAWN

FINISH

MATERIAL



TOLERANCES:


APPLICATION

USED ONNEXT ASSY


SEE BOM

A.N.

12/2/16

CABLE ASSY 16PIN IDC (-24,0,12, 20)

28.031.001.02 B




3. TEST CABLE ASSEMBLY FOR CONTINUITY AND SHORTS

610 15

915 25

1118 30

2 13


RED WIRE IS PIN 1

REVISIONS






4

A

123

B B

A

2 134



SCALE: 1:2 WEIGHT:

REVDWG. NO.

BSIZE

TITLE:

NAME DATE

COMMENTS:

Q.A.

MFG APPR.

ENG APPR.

CHECKED

DRAWN

FINISH

MATERIAL



TOLERANCES:


APPLICATION

USED ONNEXT ASSY


SEE BOM

A.N.

12/2/16


28.031.001.02 B





610 15

915 25

1118 30

2 13


RED WIRE IS PIN 1

REVISIONS






4

A

123

B B

A

2 134



SCALE: 1:2 WEIGHT:

REVDWG. NO.

BSIZE

TITLE:

NAME DATE

COMMENTS:

Q.A.

MFG APPR.

ENG APPR.

CHECKED

DRAWN

FINISH

MATERIAL



TOLERANCES:


APPLICATION

USED ONNEXT ASSY


SEE BOM

A.N.

12/2/16


28.031.001.02 B










LTM2




16-pin Tyco connectors at -34”, -26”, 0”, 26” and 34”; for connecting ALM to 4 linear boards.

864 15

203 15

1550 25

1753 30

3 21


RED WIRE IS PIN 1

REVISIONS





4

A

123

B B

A

2 134



SCALE: 1:2 WEIGHT:

REVDWG. NO.

BSIZE

TITLE:

NAME DATE

COMMENTS:

Q.A.

MFG APPR.

ENG APPR.

CHECKED

DRAWN

FINISH

MATERIAL



TOLERANCES:


APPLICATION

USED ONNEXT ASSY


SEE BOM

A.N.

11/01/16

ASSY CABLE ALM 16 (-34, -26, 0, 26, 34)

28.031.001.03 A





864 15

203 15

1550 25

1753 30

3 21


RED WIRE IS PIN 1

REVISIONS





4

A

123

B B

A

2 134



SCALE: 1:2 WEIGHT:

REVDWG. NO.

BSIZE

TITLE:

NAME DATE

COMMENTS:

Q.A.

MFG APPR.

ENG APPR.

CHECKED

DRAWN

FINISH

MATERIAL



TOLERANCES:


APPLICATION

USED ONNEXT ASSY


SEE BOM

A.N.

11/01/16

ASSY CABLE ALM 16 (-34, -26, 0, 26, 34)

28.031.001.03 A




3. TEST CABLE ASSEMBLY FOR CONTINUITY. 864 15

203 15

1550 25

1753 30

3 21


RED WIRE IS PIN 1

REVISIONS





4

A

123

B B

A

2 134



SCALE: 1:2 WEIGHT:

REVDWG. NO.

BSIZE

TITLE:

NAME DATE

COMMENTS:

Q.A.

MFG APPR.

ENG APPR.

CHECKED

DRAWN

FINISH

MATERIAL



TOLERANCES:


APPLICATION

USED ONNEXT ASSY


SEE BOM

A.N.

11/01/16

ASSY CABLE ALM 16 (-34, -26, 0, 26, 34)

28.031.001.03 A










LTM2


13.1.1 Power Cable Assembly (Nominal 24” Length)

Provides power to each module.



610

8

32X STRIP AND TIN 12

NOTES:

THE RED WIRE IS TO GO TO PIN 1. 1.

STRIP AND TIN WIRES AS SHOWN.2.

3. WIRES MUST MEET UL STYLE 1061.

4. ALTERNATE WIRE MUST MEET ALL SPECIFICATIONS ON THIS DRAWING AND BE APPROVED BY LUMENETIX ENGINEERING.

REVISIONS



2 ADDED STRIP AND TIN, NOTE. 2, 3, 4 INSPECTION DIMENSIONS 12/9/2015 A.N.


1 RED WIRE 24AWG HOOK -UP WIRE STRANDED 7/32 24AWG RED 1

2 BLACK WIRE 24AWG HOOK -UP WIRE STRANDED 7/32 24AWG BLACK 1

3 CONNECTOR MOLEX 5023510200 1

4 CRIMP MOLEX 0503728000 2

D

C

B

AA

B

C

D

12345678

8 7 6 5 4 3 2 1



NEXT ASSY USED ON

APPLICATION

DIMENSIONS ARE IN MILLIMETERSTOLERANCES:ANGULAR: MACH 0.5ONE PLACE DECIMAL 0.5TWO PLACE DECIMAL 0.15


MATERIAL

FINISH

SEE NOTES

DRAWN

CHECKED

ENG APPR.

MFG APPR.

Q.A.

COMMENTS:


SIZE

BDWG. NO. REV

WEIGHT: SCALE: 2:1


2

A.N. 12/04/15

T5 POWER CABLE

SHEET 1 OF 1

DO NOT SCALE DRAWING

28.030.001.01 Pin # Lead Color Input

Pin 1 Red Power 24V DC (+)

Pin 2 Black Power Common (-)

13.1.2 Pin Allocation Chart for Power Cable Assembly

13 POWER / CONTROL CABLE ASSEMBLIES

610

8

32X STRIP AND TIN 12

NOTES:

THE RED WIRE IS TO GO TO PIN 1. 1.

STRIP AND TIN WIRES AS SHOWN.2.

3. WIRES MUST MEET UL STYLE 1061.


REVISIONS



2 ADDED STRIP AND TIN, NOTE. 2, 3, 4 INSPECTION DIMENSIONS 12/9/2015 A.N.


1 RED WIRE 24AWG HOOK -UP WIRE STRANDED 7/32 24AWG RED 1

2 BLACK WIRE 24AWG HOOK -UP WIRE STRANDED 7/32 24AWG BLACK 1

3 CONNECTOR MOLEX 5023510200 1

4 CRIMP MOLEX 0503728000 2

D

C

B

AA

B

C

D

12345678

8 7 6 5 4 3 2 1



NEXT ASSY USED ON

APPLICATION

DIMENSIONS ARE IN MILLIMETERSTOLERANCES:ANGULAR: MACH 0.5ONE PLACE DECIMAL 0.5TWO PLACE DECIMAL 0.15


MATERIAL

FINISH

SEE NOTES

DRAWN

CHECKED

ENG APPR.

MFG APPR.

Q.A.

COMMENTS:


SIZE

BDWG. NO. REV

WEIGHT: SCALE: 2:1


2

A.N. 12/04/15

T5 POWER CABLE

SHEET 1 OF 1


28.030.001.01




LTM2


13.2.1 Control Cable Assembly (Nominal 24” Length)

Provides 0-10V control and RS-485 signals to each module.



13.2.2 Pin Allocation Chart for Control Cable Assembly

Pin # Lead Color Input

Pin 1 Violet 0-10V Dimming (+)

Pin 2 Blue 0-10V Color (+)

Pin 3 Orange Digital Data - (NOT USED)

Pin 4 White with orange stripe Digital Data + (NOT USED)

Pin 5 Brown Digital Common (NOT USED)

Pin 6 Gray 0-10V Dimming (-)

Pin 7 White 0-10V Color (-)

8±1.50

610 10

5 34 2 1689 7

7X STRIP AND TIN

NOTES:

THE VIOLET WIRE GOES TO PIN 1. 1.

2. STRIP AND TIN WIRES AS SHOWN.

3. WIRES MUST MEET UL STYLE 1061



1 874390700 MOLEX CONNECTOR 12 874210000 CRIMP 73 VIOLET WIRE 24AWG HOOK-UP WIRE STRANDED 7/32 24AWG VIOLET 14 BLUE WIRE 24AWG HOOK-UP WIRE STRANDED 7/32 24AWG BLUE 15 ORANGE WIRE 24AWG HOOK-UP WIRE STRANDED 7/32 24AWG ORANGE 1

6 WHITE WITH ORANGE STRIPE WIRE 24AWG

HOOK-UP WIRE STRANDED 7/32 24AWG WHITE WITH ORANGE STRIPE 1

7 BROWN WIRE 24AWG HOOK-UP WIRE STRANDED 7/32 24AWG BROWN 18 GREY WIRE 24AWG HOOK-UP WIRE STRANDED 7/32 24AWG GREY 19 WHITE WIRE 24AWG HOOK-UP WIRE STRANDED 7/32 24AWG WHITE 1

REVISIONS



B ADDED NOTE 2 AND 3 10/6/2014 A.N.

C ADDED MOLEX TO THE CONNECTOR AND CRIMP 10/21/2014 A.N.

D CABLE LENGTH TO 610 AND STRIP TO 8 LONG 3/5/2015 A.N.

E CHANGED UL FROM 1569 TO 1061 5/28/2015 A.N.

F REMOVED THE PART NUMBER OFF THE WIRES. ADDED DESCRIPTION OF WIRES 12/29/2015 A.N.

G REPLACED GREEN WIRE WITH WHITE WITH ORANGE STRIPE 9/9/2016 A.N.

D

C

B

AA

B

C

D

12345678

8 7 6 5 4 3 2 1



NEXT ASSY USED ON

APPLICATION

DIMENSIONS ARE IN MILLIMETERSTOLERANCES:ANGULAR: MACH 0.5LINEAR TOLERANCE 0.5


MATERIAL

FINISH

SEE NOTES

DRAWN

CHECKED

ENG APPR.

MFG APPR.

Q.A.

COMMENTS:


SIZE

BDWG. NO. REV

WEIGHT: SCALE: 2:1


G

A.N. 03/25/14

CONTROL CABLE ASSEMBLY, 7 WIRE

SHEET 1 OF 1


28.002.002.01

8±1.50

610 10

5 34 2 1689 7

7X STRIP AND TIN

NOTES:

THE VIOLET WIRE GOES TO PIN 1. 1.

2. STRIP AND TIN WIRES AS SHOWN.

3. WIRES MUST MEET UL STYLE 1061



1 874390700 MOLEX CONNECTOR 12 874210000 CRIMP 73 VIOLET WIRE 24AWG HOOK-UP WIRE STRANDED 7/32 24AWG VIOLET 14 BLUE WIRE 24AWG HOOK-UP WIRE STRANDED 7/32 24AWG BLUE 15 ORANGE WIRE 24AWG HOOK-UP WIRE STRANDED 7/32 24AWG ORANGE 1

6 WHITE WITH ORANGE STRIPE WIRE 24AWG

HOOK-UP WIRE STRANDED 7/32 24AWG WHITE WITH ORANGE STRIPE 1

7 BROWN WIRE 24AWG HOOK-UP WIRE STRANDED 7/32 24AWG BROWN 18 GREY WIRE 24AWG HOOK-UP WIRE STRANDED 7/32 24AWG GREY 19 WHITE WIRE 24AWG HOOK-UP WIRE STRANDED 7/32 24AWG WHITE 1

REVISIONS



B ADDED NOTE 2 AND 3 10/6/2014 A.N.

C ADDED MOLEX TO THE CONNECTOR AND CRIMP 10/21/2014 A.N.

D CABLE LENGTH TO 610 AND STRIP TO 8 LONG 3/5/2015 A.N.

E CHANGED UL FROM 1569 TO 1061 5/28/2015 A.N.

F REMOVED THE PART NUMBER OFF THE WIRES. ADDED DESCRIPTION OF WIRES 12/29/2015 A.N.

G REPLACED GREEN WIRE WITH WHITE WITH ORANGE STRIPE 9/9/2016 A.N.

D

C

B

AA

B

C

D

12345678

8 7 6 5 4 3 2 1



NEXT ASSY USED ON

APPLICATION

DIMENSIONS ARE IN MILLIMETERSTOLERANCES:ANGULAR: MACH 0.5LINEAR TOLERANCE 0.5


MATERIAL

FINISH

SEE NOTES

DRAWN

CHECKED

ENG APPR.

MFG APPR.

Q.A.

COMMENTS:


SIZE

BDWG. NO. REV

WEIGHT: SCALE: 2:1


G

A.N. 03/25/14

CONTROL CABLE ASSEMBLY, 7 WIRE

SHEET 1 OF 1


28.002.002.01

13 POWER / CONTROL CABLE ASSEMBLIES




LTM2


14 WIRING DIAGRAMS

14.1 0-10V Best Wiring Practice

0 - 10V PROTOCOL

0-10V Best Wiring Practice

Any manufacturer that makes a dimmer that sinks will work with Lumenetix modules since we source the voltage.

0-10V is a topology defi ned by the International Electrotechnical Commission (IECR) 60929 Annex E standard and uses a varying DC voltage between 1 and 10V to determine the lighting level. The fi xture outputs a minimum light level below 1V w hich is defi ned as low-end . Between 1 and 10V, t h e signal corresponds to levels between the minimum and maximum output level. A signal above 10V corresponds to the maximum light level. Sometimes it is referred to as 1-10V, as that is the actual range in which the light levels will vary . Each dimmer will have their own distinct dimming profi le.

Best practice is to limit the distance run for the analog control wiring from the controller to the last driver to 300’, as a common 0-10V DC wiring type is stranded-copper twisted-pair 18AWG wiring. The wiring is stranded copper because it provides a more stable current path (as DC signals tend to be transferred by the outer edges of the conductor) while being relatively easy to work with; solid wire is usually acceptable in low-voltage systems that use

AC control power.

Whenever any part of the control circuit (the driver, dimer, or wire used) is designed for use in a Class 2 installation, it is critical that the entire control circuit be kept separate from Class 1 line voltage wiring per the requirement of National Electric Code, section 725.136. The electrical drawings must be very clear that class 1 and class 2 wiring cannot be combined. There must be separation because: a) it is possible for higher voltage wiring to induce an AC voltage in to the low voltage signal wiring; and, b) undesirable visual artifacts in the dimmed lighting can be caused when the line and low voltage wiring is run together (especially for long distances). We do not recommend installing the low voltage signal wiring in the same conduit or raceway as line voltage

wiring even when all elements of the control circuit are listed for Class 1 wiring methods.

NOTE: Lumenetix modules operate between 1-10V. All dimmers that have minimum and maximum trim pots should be set at a minimum of 1 volt and a

maximum of 10 volts, measuring the voltage at the end of the line.

0-10V Dimmers (recommended list)*Crestron

ETC

Fresco

Legrand

Leviton

Lutron

Nexlight

N-Light

Pass & Seymour

Vantage

Wattstopper

*Recommendations are subject to change. Consult your Lumenetix representative for the most updated list.




LTM2


14 WIRING DIAGRAMS

14.1.1 0-10V Wiring Diagram

0 - 10V WIRING DIAGRAMS

LTM2 Linear Array - 24V

INDEX TAB ON RED END OF CABLE CONNECTOR SHOULD LINE UP WITH INDEX SLOT ON ALM.

RIBBON CONNECTOR CABLE

TUNABLE COLOR LINEAR LED ARRAY

FIXTURE

WHITE (NEUTRAL)

BLACK (HOT)RED (+)

BLACK (Common)

LINE-IN VOLTAGE(REFER TOPOWER SUPPLY)

ALM 24V POWER CABLE (28.030.001.01)

JUNCTION BOX

araya5 LOGIC MODULE (ALM)

MAKE SURE TO ALIGNINDEX TAB TO INDEX SLOT.

CLASS-2 AC TO DC24V POWER SUPPLY(SUPPLIED BY OEM)

DIGITAL WIRES (ORANGE / WHITE WITH ORANGE STRIPE / BROWN) SHOULD REMAIN OPEN

0-10V CONTROLLER (DIM)

0-10V CONTROLLER (CCT)

VIOLET (+)

GRAY (-)

BLUE (+)

WHITE (-)

ALM 7-WIRE CONTROL CABLE (28.002.002.01)

THE CONSTANT HOT/LIVE MUST BE WIREDTO A SWITCHING DEVICE.




LTM2


14.2 Bluetooth Operation using the araya®5 Tunable Color 2.0 iOS App



FIXTURE

WHITE (NEUTRAL)

BLACK (HOT)RED (+)

BLACK (Common)



JUNCTION BOX




TUNABLE COLOR 2.0 iOS APP

(MAX. OF 8 MODULES CAN BECOMMISSIONED AT A TIME)

14 WIRING DIAGRAMS

NOTE: BLUETOOTH OPERATION IS FOR COMMISSIONING THE MODULES ONLY, NOT FOR CONTROLLING THEM.




LTM2


14.3 DMX512-A Protocol

14 WIRING DIAGRAMS DMX512-A PROTOCOL

DMX512-A is an acronym for Digital Multiplex, a communication protocol used to remotely control lighting dimmers and intelligent fi xtures. It is designed to provide a common communications standard between these lighting devices regardless of the manufacturer. The 512-A after the DMX refers to the number of control channels used on one network segment (often called a ‘universe’) of devices. In a simple dimming system, one channel controls the intensity of the fi xture. A single intelligent fi xture such as the araya5 requires several channels to control its various parameters (one channel each for DIM,

CCT, SAT, HUE).

DMX512A Specifi cations:• DMX 512-A (Controller).

• A universe is 512 Channels.

• DMX value is between 0 and 255, where 0 is off and 255 is full on.

• The maximum number of devices in a daisy-chain wire run is 32, which include the controller and opto-splitter.

• The maximum network wire run is a distance of up to 1600 feet for non-RDM systems and up to 1000 feet for RDM systems.

• One device functions as the master (DMX controller) on a network, while the rest function as slaves (mergers, splitters, intelligent fi xtures, etc.).

• Only the controller (master) transmits over the network, and all fi xtures receive the same data.

• The fi nal device in the daisy-chain must be terminated with a 120 ohm resistor between DMX+ and DMX- pins.

• It is recommended that the terminator for the fi nal device be located in the control panel, if it falls within the recommended wiring distance.

• All wiring must be in a continuous run and daisy-chained.

• Star wiring is only allowed in conjunction with an opto-splitter.

• Do not run DMX control cable in close proximity to AC power lines. EM spikes from switching of high-current devices such as HVAC equipment or generators will induce noise into the DMX cable.

• The shield must be carried through between modules and properly grounded at one point only.

• Connections to DMX512-A-RDM accessory board: wire size to be 24AWG, and solid or stranded cables may be used. Stranded wire used must be tinned or installed with ferule connector.

RDM

DMX512-A control protocol that enables Remote Device Management for two-way communications for confi guration, monitoring and system setup. Allows two way communication between lighting controller and the fi xtures. Allows for remote setting of DMX start addressing. RDM signals are sent back the other way, but not constantly. Controller can ask one or more devices for query feedback. RDM packets are inserted in-between the existing DMX data packets being used to control the lighting. The DMX Control Console will broadcast up to 512 channels over one DMX cable (max. run of 1000 feet for RDM). Some of these channels may not be used, but will still be transmitted, as required by the protocol. It must be set to a desired channel (001, 002. 003. 004, etc.) to control the connected light fi xture. This is usually accomplished using RDM. This desired ‘channel’ is commonly known as the DMX address. When addressing fi xtures, it is not recommended to skip addresses.

When RDM is not available with the control system, it is permissible to use the Lumenetix commissioning tool (the araya5 Tunable Color 2.0 iOS App) to set

the address of the slots. The instructions to confi gure the DMX channels can be found in the separate araya5 Tunable Color Instruction Manual.

The DMX512-A interface follows the ANSI E1.11-2008 (R21013) standard. Four address slots are allocated to each interface board and control the Dim

level, CCT, Saturation and Hue of the araya5 modules connected to the board.

Default DMX512-A Slot Allocation:

Slot Function

1 Dim Level

2 CCT

3 Saturation Level

4 Hue

DMX512-A Protocol




LTM2


14.3.1 DMX512-A Electrical Specifications

14 WIRING DIAGRAMSDMX512-A PROTOCOL

DMX512-A Electrical Specifi cations

Parameter Range Remarks

ESD Protection ±15KV (air), ±8KV (conducted) Per IEC 61000-4-2

Termination Recommended The DMX512 bus termination rules apply

Directionality Receive only

Frequency stability ±20ppm

Load per port 1/256 1/8 of Nominal RS-485

Isolation 3KVrms

DMX512-A Control Systems (recommended list)Choreo

Cognito

Crestron Greenlight System

Entec

ETC Mosaic

ETC Paradigm

Fresco

Interactive Technologies

Lutron HomeWorks QS

Lutron Quantum

Nicolaudie

Pathway Connectivity

Pharos

Traxon Ecue

Vantage Controls


DMX512-A Recommended Internal / Field Wiring

TMB Cable ProPlex DMXPC224T: 2-pair DMX512 cable, overall foil and braid shielding with drain wire. UV and fungus resistant. Fully rated for installations, yet easy

handling for light duty portable applications.

PC224TW: Same as above, with white jacket.

For use as DMX in/out under one jacket:

PC244T: Two individually shielded pairs and drain wires. UV resistant. Color coded foil shielding for easy reference.




LTM2


14 WIRING DIAGRAMS

14.3.2 DMX512-A Recommended Field Wiring

DMX512-A PROTOCOL

DMX512-A Recommended Field WiringLiberty 24-2P-485 (Non-Plenum), 24 AWG, 2 pair dual 120 ohm, 11.2 pf/ft low capacitance (Wago, XLR and PHX connectors)Liberty 24-2P-P485 (Plenum), 24 AWG, 2 pair dual 120 ohm, 11.2 pf/ft low capacitance (XLR and PHX connectors)Belden #9842 (Non-Plenum), 24 AWG, 2 pair dual shielded 120 ohm, 12.8 pf/ft low capacitance (XLR and PHX connectors)Belden #89842 (Plenum), 24 AWG, 2 pair dual shielded 120 ohm, 12.8 pf/ft low capacitance (XLR and PHX connectors)

Please refer to wire manufacturer’s lighting catalog for and/equals as required by code.

Category Wire or EqualThe Entertainment Services and Technology Association (ESTA) does not defi ne a maximum run length for DMX over Cat5 since many factors will affect the maximum run length, such as number of devices, number of splices in the cable, the strength of the DMX transmitter(s), if Remote Device Management (RDM) is being used, and sources of interference. ESTA does state (again, in ANSI E1.21-2):

“A properly selected and installed DMX512 cable should provide acceptable signal strength for runs of 300m (1000ft). Please note that the technical requirements, such as run-length and topology for other networking technologies, such as Ethernet, should be considered if using the installed cable for another networking technology in the future is anticipated.”

Cat5 or equivalent is not preferred as a portable cable since it is not as rugged as other DMX cables. Male RJ45 connectors are especially prone to breakage over repeated re-connections.

LUMENETIX RECOMMENDATION:

CAT 5E -150 FEET

CRESTRON

DM-CBL-8G-NP

DM-CBL-8G-P

CAT 7- 330 FEET

CRESTRON

DM-CBL-ULTRA-NP

DM-CBL-ULTRA-P

DMX512-A Recommended Field Connectors (or Equal)WAGO 221

PHOENIX CONTACT

XLR NEUTRIK

CRESTRON

RJ45 DM -8G-CONN

RJ45 IDC DM-CONN

DMX512-A Wiring Connections

Signal Description Pin Colors (4-Pair Cable) Pin Colors (2-Pair Cable)3-pin XLR connector

5-Pin XLR connector

5-Pin PHX connector

Signal Common White/Brown and Brown White/Blue and Blue 1 1 1

Data (-) Primary Data Link Orange Orange 2 2 2

Data (+) Primary Data Link White/Orange White/Orange 3 3 3

Data2 (-), or not used Optional Secondary Data Link 4 4

Data2 (+), or not used Optional Secondary Data Link 5 5

RJ-45 Connector Pin-Out (T568B)XLR Connectors (5-Pin)

+-




LTM2


14 WIRING DIAGRAMS

14.3.3 DMX512-A Controller Example

DMX512-A PROTOCOL

DMX512-A Drain Wire Connections

Drain wire connections are required as follows.

Shielding

To add another level of protection from electromagnetic noise, a grounded shield is added over the twisted pair wires. When this is enclosed in a protective jacket, to avoid ground loops and electromagnetic contamination of the ground system, all control ground wiring, including cable shields and drain wires, should be treated like sensitive current-carrying conductors. All control ground wires should be insulated (not bare) and the same wiring practices should be observed with ground wires as with other sensitive signals. Care must also be taken when designing control wiring to ensure that each shield is connected to only a single ground point. You should establish this point at a central location, like a control panel or cabinet, and avoid all connection to grounds in the fi eld. A control ground is sometimes referred to as an isolated ground (an oxymoron) for this reason, but the term single-point ground is more accurate.

Method-1

A typical two-pair shielded cable can be prepared for termination to the terminals with the drain wire cut off. This is usually done at the fi eld end of the cable where no shield grounding is desired. You will then use insulating tape or heat-shrink tubing to protect the cable from contamination and to prevent accidental grounding of the shield or drain wire. An accidental ground at this point would almost certainly create an undesirable ground loop.

Method-2

A typical two-pair shielded cable can be prepared for termination to the terminals with the drain wire cut off. The drain wire, which is an uninsulated conductor, is sleeved with a insulating tubing to prevent accidental grounding. The crimp-on lug is valuable in this instance to retain the tubing. Insulating tape or heat-shrink tubing is again used to protect the cable from contamination and to prevent accidental grounding, since any accidental connection between the drain wire and a chassis, frame, or enclosure would almost certainly create a ground loop.

DMX512-A Controller Example

Up to 30devices on each loop

Bus

DMX Loop 1

DMX Loop 2

Power Module

DMXController

Processor TouchPanel

Contact Closure Interface

Wallstation

120 / 230 V~

Control Power total devices

Power Supply

Shade / Drapery

DMX512A Example

RDM Merger / Splitter

*Fixture refers to a luminaire with one Lumenetix module, and with one address (DDM) or four addresses (CTM).




LTM2


14.3.4 DMX512-A-RDM Control Card Wiring Diagram

14 WIRING DIAGRAMS DMX512-A WIRING DIAGRAMS

DMX512-A-RDM Accessory Card Wiring Diagramaraya5 Logic Module (ALM) with Linear Arrays

Notes:

1. 24V power (red/black) is Class-2 rated.

2. Adapter is confi gured at factory for DMX inputs.

3. If more than one line of DMX is needed, then a DMX Splitter must be used to create multiple independent branches of a DMX signal and/or to extend the usable distance of each branch. Each of the splitter’s 4, 6, 8, or 16 output ports generates an independently protected DMX signal.



FIXTURE

WHITE (NEUTRAL)

BLACK (HOT)RED (+)

BLACK (Common)



DMX wiring provided by others.

JUNCTION BOX


The Constant Hot/Live must not be wired to a switching device.This may be put on a relayfor maintenance.

DMX SLOTS SET BY RDM ORBY TUNABLE COLOR 2.0 iOS APP

(MAX. OF 8 MODULES CAN BECOMMISSIONED AT A TIME)



DMX OUTDMX IN

BROWN

WHITE WITH ORANGE STRIPEDATA (+)

COMMONCOMMON

DATA (-)

DATA (+)

ORANGEDATA (-)

BROWN

WHITE WITH ORANGE STRIPEORANGE

NOTE: BLUETOOTH OPERATION IS FOR COMMISSIONING THE MODULES ONLY, NOT FOR CONTROLLING THEM.




LTM2


14.4 Lutron® EcoSystem Protocol

14 WIRING DIAGRAMS LUTRON® ECOSYSTEM PROTOCOL

Lutron® EcoSystem Protocol

EcoSystem technology is a control method for LEDs that provides addressing of individual fi xtures and status feedback. This makes it easy to digitally assign one or many fi xtures without complicated wiring. This opens up an entire suite of energy-saving, system-monitoring and system-control schemes where the design, setup and rezoning are all done within software, making the electrical and control design simple.

The araya®5 modules attached to different interface boards can be controlled independently or assigned to a single group by the EcoSystem controller.

The EcoSystem control is responsible for saving any confi guration settings. Once an interface board is assigned a pair of addresses, assigned addresses are saved in NVRAM. During the EcoSystem discovery process, the user pairs the desired dimming control in the controller to the Dim channel address in the interface board. The same applies for the CCT channel.

• 1 pair 16AWG Eco Loop, 900 feet (fi eld wiring).

• Maximum of 64 addresses on each loop.

EcoSystem Control Systems (recommended list)*

Quantum System

HomeWorks QS

Grafi k Eye QS Control Unit with EcoSystem

EnergiSavr Node with EcoSystem

Power Module with EcoSystem


® Specif icat ion Submittal page

Job Name:

Job Number:

Model Numbers:

Power Module with EcoSystemR LQSE-2ECO-D EcoSystemR Controller

369611b 1 10.22.13

MU

X

CO

M

MU

X

QS ECO 1 ECO 2

Test PruebaTester

Ta > 65 ºC

L N

Patent: 7,391,297

500-

1553

7 R

ev. A

NEC® Class 2

NEC® Class 2IEC PELV

0,5 N•m (5 in-lbs) Ta ≤ 65 °C www.lutron.com

u

Z096

65/75 ºC Cu Al

Power Module with EcoSystem® | Módulo de Potencia con EcoSystem® | Module d’Alimentation avec EcoSystem®

LQSE-2ECO-D

243C IND.CONT.EQ.

8 mm

1.800.523.9466

+44.(0)20.7702.0657230 V~ 50/60 Hz 80 mA

120 V~ 50/60 Hz 120 mA

Power Module with EcoSystemR

The Power Module with EcoSystemR unit is a DIN-rail mounted EcoSystem® Loop controller for EcoSystemR ballasts, drivers and devices. It provides EcoSystemR Loop power and control for two independent EcoSystemR Loops with up to 64 ballasts or drivers each.

Features• Provides EcoSystemR Loop power for two loops

of EcoSystemR ballasts or drivers (up to 250 mA per loop).

• Power failure memory retains control unitprogramming in the event of a power loss.

• Includes QS Link for connection to aHomeWorksR QS system.

• Power Module with EcoSystemR unit can be used ina HomeWorksR QS system to control and managelight in an entire home or building.

Up to 64 devices on each loop for Eco-1, and up to 32 devices on each loop for Eco-2

QS Link

Eco Loop 1

Eco Loop 2Fixture*

Power Module

Power Module with EcoSystem®

HomeWorksR QS Processor

GRAFIK EyeR QS

QS Contact Closure Interface

HomeWorksR QS Wallstation

120 / 230 V~ Control Power Up to 100

total QS devices

QS Power Supply

SivoiaR QS Shade / Drapery

Lutron EcoSystem Example

Fixture*

Fixture* Fixture*

*Fixture refers to a luminaire with one Lumenetix module, and with one address (DDM) or two addresses (CTM).

1

Lutron EcoSystem Controller Example




LTM2


14.4.1 Lutron® EcoSystem Field Wiring

14 WIRING DIAGRAMSLUTRON® ECOSYSTEM PROTOCOL

Lutron® EcoSystem Field Wiring

• EcoSystem Digital Loop can be wired as Mains voltage or IEC PELV/NECR Class 2 for maximum wiring fl exibility..

• The Loop is polarity insensitive and can be wired in any topology..

• Consult all national and local electrical codes for separation requirements..

Wire Gauge Maximum EcoSystem-Compliant Loop Wire Length

4.0 mm2 (12 AWG) 671 m (2200 ft)

2.5 mm2 (14 AWG) 427 m (1400 ft)

1.5 mm2 (16 AWG) 275 m (900 ft)

1.0 mm2 (18 AWG) 175 m (570 ft)

Drain Wire ConnectionsDrain wire connections are required as follows.

Shielding

To add another level of protection from electromagnetic noise, a grounded shield is added over the twisted pair wires. When this is enclosed in a protective jacket, to avoid ground loops and electromagnetic contamination of the ground system, all control ground wiring, including cable shields and drain wires, should be treated like sensitive current-carrying conductors. All control ground wires should be insulated (not bare) and the same wiring practices should be observed with ground wires as with other sensitive signals. Care must also be taken when designing control wiring to ensure that each shield is connected to only a single ground point. You should establish this point at a central location, like a control panel or cabinet, and avoid all connection to grounds in the fi eld. A control ground is sometimes referred to as an isolated ground (an oxymoron) for this reason, but the term single-point ground is more accurate.

Method-1

A typical two-pair shielded cable can be prepared for termination to the terminals with the drain wire cut off. This is usually done at the fi eld end of the cable where no shield grounding is desired. You will then use insulating tape or heat-shrink tubing to protect the cable from contamination and to prevent accidental grounding of the shield or drain wire. An accidental ground at this point would almost certainly create an undesirable ground loop.

Method-2

A typical two-pair shielded cable can be prepared for termination to the terminals with the drain wire cut off. The drain wire, which is an uninsulated conductor, is sleeved with a insulating tubing to prevent accidental grounding. The crimp-on lug is valuable in this instance to retain the tubing. Insulating tape or heat-shrink tubing is again used to protect the cable from contamination and to prevent accidental grounding, since any accidental connection between the drain wire and a chassis, frame, or enclosure would almost certainly create a ground loop.




LTM2


14.4.2 Lutron® EcoSystem Control Card Wiring Diagram

14 WIRING DIAGRAMS LUTRON® ECOSYSTEM WIRING DIAGRAMS

Lutron® EcoSystem Accessory Card Wiring Diagramaraya5 Logic Module (ALM) with Linear Arrays

Notes:


2. EcoSystem Channel 1 is always Intensity control. EcoSystem Channel 2 is always CCT control.

3. In the EcoSystem programming mode, EcoSystem Channel 1 controls the intensity from 100%-1%. EcoSystem Channel 2 controls the CCT range from 1650 - 8000K.

4. The araya5 Tunable Color 2.0 iOS App should be turned on, and the DMX channels should be set to 2, 4, 6, 8.


WHITE (NEUTRAL)

BLACK (HOT)CLASS-2 AC TO DC24V POWER SUPPLY

E1

E2

RED (+)

BLACK (Common)

(SUPPLIED BY OEM)



The Constant Hot/Live must not be wired to a switching device.This may be put on a relay formaintenance.

Fixture manufacturer to provide minimum 18 AWG ofLutron EcoSystem wire tail (labeled E1 and E2) to junction box.Consult Lutron for �eld wiring.

WHITE / VIOLET STRIPES

VIOLET

FIXTURE

E1E2

JUNCTION BOX

LUTRON ECOSYSTEM CONTROLLER

ALM WITH LUTRON ACCESSORY BOARD ALM 24V POWER CABLE (28.030.001.01)




LTM2


14 WIRING DIAGRAMS

14.5 DALI Type 8 Protocol Specifications

DALI TYPE 8 PROTOCOL

DALI Type 8 Protocol Specifi cations

Digital Addressable Lighting Interface (DALI) is a communication language. DALI facilitates the communication and therefore control of multiple devices such as drivers, transformers and other lighting equipment. Devices which speak the same language can exchange information, in much the same way

people can exchange information when they communicate using the same language.

DALI Devices:Designed on a distributed intelligent framework, each DALI device has on-board memory that stores all relevant information about the device, including diagnostics, which reduces the technical requirements on the control system and the amount of data to be transmitted over the line.

DALI Standards:• DALI is a lighting control standard defi ned under the European Standard IEC 62386 .

• IEC stands for International Electrotechnical Commission and is a non-profi t organization.

• DALI was designed to replace traditional 1-10 V analog systems and proprietary digital systems such as DSI (Digital Serial Interface).

• At a maximum there can be 64 DALI devices on a single DALI line and it has a data baud rate of 1200 baud.

DALI Technical Specifi cations:

Numbers of units: max. 64

Numbers of addresses: 64

Signal level: +/- 16V

Cable length: max. 300m, and less than 2V voltage drop

Cable type: any 2 wire unshielded cable

Cable topology: any (line, star, tree, ring)

Refresh rate: max 40 messages / second +/- 1200 baud Safety

DALI is not SELV; cable must be treated like mains wiring

Maximum DALI-compliant Bus Wire Length:

1.5 mm2 (300 m)

0.75 mm2 (150 m)

0.50 mm2 (100 m)

A DALI system contains one current source, a controller and input(s). In idle state the current signal is “high”so there is current. A driver input current is 2mA in idle state. Nominal current for 64 inputs is 128mA. Information is transferred by short circuiting the current, (controller / input). Communication is always started by the controller. An input can only “answer” (=back channel info). Random addressing is possible. DALI units

have no address from factory. Any address can be changed via the DALI connection. An input can detect if the DALI current is present.




LTM2


14 WIRING DIAGRAMS

14.5.1 DALI Type 8 Wiring Specifications

DALI TYPE 8 PROTOCOL

DALI Type 8 Wiring Specifi cations

DALI Wiring can be run up to 300m using 1.5mm cable. (15 awg) The DALI specifi cation allows for maximum 2V drop in the communication signal. The DALI line does not require termination of the line and supports all wiring typologies except rings and closed loops (trees, branches and chains are all acceptable).

The following are National Electric Code (NEC 70) requirements.

DALI Class 1 and Class 2 Wiring Overview:

DALI dimming ballasts and drivers are connected together by a 2-wire low voltage bus that is suitable for Class 1 or Class 2 wiring installations. This application note explains how both Class 1 and 2 wiring are made and how they both meet National Electric Code (NEC) regulations.

DALI Dimming Ballast and Driver Wired Class 2:

For more information on Class 2 wiring and additional Class 2 wiring requirements see National Electric Code Article 725. With regards to factory installed wiring, as per UL1598 section 6.17.1: Factory-installed power limited wiring and branch circuit wiring that come in random contact within the luminaire shall have insulation rated for the maximum voltage that exists in any of the circuits.

If wiring with the properly rated insulation is used, then no spacing or separation is required regardless of the circuit conductor voltage although shielding may be required.

Class 2 wiring of the DALI dimming ballast and driver follows the NEC Requirement 725.136(D) (references to Class 3 are eliminated).

Class 2 circuit conductors in compartments, enclosures, device boxes, outlet boxes, or similar fi ttings shall be permitted to be installed with electric light, power, Class 1 circuits where they are introduced solely to connect the equipment connected to Class 2 circuits and where (1) or (2) applies:

1. The electric light, power, Class 1 circuit conductors are routed to maintain a minimum of 6 mm (.25 in) separation from the conductors and cables of Class 2.

2. The circuit conductors operate at 150 volts or less to ground and also comply with one of the following:

A. The Class 2 circuits are installed using Type CL3, CL3R, or CL3P or permitted substitute cables provided these Class 3 cable conductors extending beyond the jacket are separated by a minimum of 6 mm (0.25 in) or by a nonconductive sleeve or nonconductive barrier from all other conductors.

B. The Class 2 circuit conductors are installed as a Class 1 circuit.

The DALI dimming ballast and driver have a minimum spacing of 0.25 inches between line voltage and the bus terminals (purple and grey wires) for Class 2 installations.

DALI Bus Wired Class 1:

Class 1 wiring methods follow the NEC Requirement 725.48.

Class 1 circuits shall be permitted to be installed with other circuits as specifi ed in 725.48 (A) and (B):

A. Class 1 circuits shall be permitted to occupy the same cable, cable tray, enclosure, or raceway without regard to whether the individual circuits are alternating or direct current, provided all conductors are insulated for the maximum voltage of any conductors in the cable, cable tray, enclosure or raceway.

B. Class 1 circuits shall be permitted to be installed with power supply conductors as specifi ed:

1. Class 1 and power supply circuits shall be permitted to occupy the same cable, enclosure, or raceway only when functionally associated.

Since the DALI dimming ballast and driver meets Class 2 installation requirements, it can also be installed in a Class 1 confi guration when Class 2 markings are not present. The NEC allows the reclassifi cation of Class 2 circuits per Article 725.130 Exception No.2:

Class 2 and circuits shall be permitted to be reclassifi ed and installed as Class 1 circuits if the Class 2 markings are eliminated and the entire circuit is installed using the wiring methods and materials in accordance with Part II, Class 1 circuits.

Note: For more information regarding Class 2 wiring and additional requirements see the National Electrical Code Article 725.

Reference Information:

Code quotation, guidance, and wiring guides above are listed for reference only. Always follow local and national wiring requirements. NEC 2008 was used as a reference in this Application Note. More recent releases of the National Electrical Code should always be consulted. The National Electrical Code (NEC) is a registered trademark of the National Fire Protection Association, Quincy, MA.




LTM2


14 WIRING DIAGRAMS

14.5.2 DALI Type 8 Control Card Wiring Diagram

DALI TYPE 8 WIRING DIAGRAMS

DALI Type 8 Accessory Card Wiring Diagramaraya5 Logic Module (ALM) with Linear Arrays


WHITE (NEUTRAL)

BLACK (HOT)CLASS-2 AC TO DC24V POWER SUPPLY

RED (+)

BLACK (Common)

(SUPPLIED BY OEM)



The Constant Hot/Live must not be wired to a switching device.This may be put on a relay formaintenance.

Fixture manufacturer to provide minimum 18 AWG ofDALI wire tail to junction box.Consult DALI speci�cations for �eld wiring.

FIXTURE

JUNCTION BOX

DALI CONTROLLER


D1D2

ALM WITH DALI TYPE 8 ACCESSORY BOARD

Notes:


2. One DALI address per linear array / ALM kit.




LTM2


15 PRE-INSTALLATION NOTES

TUNABLE COLOR LINEAR LED ARRAYS (PRINTED CIRCUIT BOARDS)

• To ensure proper electrical insulation between the linear arrays and heat sink, the linear arrays (PCBS) are provided with a pre-applied double sided adhesive insulating tape. Be sure to remove the plastic liner before attaching the linear array to the heat sink.

• Ensure that the PCBs are properly aligned with reference arrows facing each other (see image below). This is critical for proper mixing.

• Exercise caution when connecting the ribbon cables to the LED PCBs. Do not press the LEDs against a hard surface (like a table or workbench) as they can be damaged. Do not break off the indexing tabs.

• IMPORTANT: Please allow a space of 2 mm - 5 mm between the LED PCBs. Do NOT butt the LED PCBs to each other. If a 2 mm - 5 mm spacing is not provided, the LED PCBs may bow. Gaps larger than 5 mm may not have proper color mixing.

• Mount the LED PCB to the fixture using 6 mm - 8 mm (M2.5 - M4) screws. PLEASE NOTE: Use plastic washers to protect the PCB. Do NOT over-tighten the screws, since that can damage the LED PCB.

• PCBs need to be isothermal (intra-board and inter-board). ALMs can be mounted on a different thermal platform.

REFLECTOR END CAPS

• Test-fit the reflector end caps on the LED PDBs. Note that the opening (with diffuser) should face in the OPPOSITE direction of the alignment arrows. The mounting hole should match the hole on the reflector end caps.

• The reflector end caps are fastened to the fixture using 6 mm - 8 mm (M2.5 - M4) screws inserted through the end caps and the holes in the LED PCB. The opposite side where it is not fastened must be used with double-sided tape.NOTE: The end caps will cover the last few LEDs.

RIBBON CABLE CONNECTORS

• The surface of the fixture to which the PCB is mounted must have relief areas for the connectors.

• Leave adequate clearance around the ribbon cable connector so that it does not come in contact with the fixture’s metal edge.

• Cut-outs in the heat sink around the connectors should be made as large as possible to avoid potential shorting. Adding insulation around the cutout using polyimide tape is recommended.

araya5 LOGIC MODULE

• Mount the araya5 Logic Module to the fixture with 6 mm - 8 mm (M2.5 - M4) screws in desired location.

Test-fit all components prior to installation. Mark edges for correct alignment.




LTM2


16 LINEAR ARRAY CONFIGURATION EXAMPLES

16.1 1-Foot Linear Array Configuration Example

ro:: ro:: ro:: ro:: ro:: ro::.ro:: ·ro:: ·ro:: .ro:: ro:: .ro::-ro::-ro::-ro:: .ro:: ro:: ·ro::-ro:: .ro:: ro::.ro:: ·ro:: ro::-ro::-ro::-ro::-ro::-ro:: ·l[[:-1[[:-I[[: .:[[: .ro::-u:-1[[: -ro:. -u: trI ·ro::-ro::-1[[ () ()

<�:::i 0 0

2-wire power cable assembly

(28.030.001.01)

10W ALM 24” flat ribbon cable

(28.030.002.02)

11 in. linear board

Reflector end caps; set of 2

(45.001.011.01)

11 inches Linear LED Array Kit: 80.001.090.01Ordering code includes: one 11 in. linear LED board and 10W araya5 Logic Module.0-10V; Bluetooth-enabled for iOS commissioning.

To implement the above configuration, the following items must be added to the order:2-wire power cable assembly: 28.030.001.0124” flat ribbon cable; 16-pin Tyco connectors at each end: 28.030.002.02Reflector end caps (set of 2): 45.001.011.01

To implement 0-10V Control of the above, the following items must also be added to the order:7-wire control cable assembly: 28.002.002.01

To implement DMX512-A control of the above, the following items must also be added to the order:DMX512-A-RDM Control Card: 80.003.001.01

To implement Lutron EcoSystem control of the above, the following items must also be added to the order:Lutron Control Card: 80.003.002.02




LTM2




(28.030.001.01)


(28.030.002.02)

22 in. or 24 in. linear board


(45.001.011.01)

22 inches Linear LED Array Kit: 80.001.091.01, OR24 inches Linear LED Array Kit: 80.001.201.01Ordering code includes: one 22 in. or one 24 in. linear LED board and 20W araya5 Logic Module.0-10V; Bluetooth-enabled for iOS commissioning.

To implement the above configuration, the following items must be added to the order:2-wire power cable assembly: 28.030.001.0124” flat ribbon cable; 16-pin Tyco connectors at each end: 28.030.002.02Reflector end caps (set of 2): 45.001.011.01


To implement DMX512-A control:DMX512-A-RDM Control Card: 80.003.001.01






LTM2




(28.030.001.01)


(28.031.001.01)

22 in. linear board

33 inches Linear LED Array Kit: 80.001.092.01Ordering code includes: one 22 in. linear LED board, one 11 in. linear LED board and 30W araya5 Logic Module.0-10V; Bluetooth-enabled for iOS commissioning.

To implement the above configuration, the following items must be added to the order:2-wire power cable assembly: 28.030.001.0132” flat ribbon cable; 16-pin Tyco connectors at 0”, 24” and 32”: 28.031.001.01Reflector end caps (set of 2): 45.001.011.01





<�:::i 0 0


(45.001.011.01)

11 in. linear board





LTM2




(28.030.001.01)


(28.031.001.01)


44 inches Linear LED Array Kit: 80.001.093.01, OR48 inches Linear LED Array Kit: 80.001.200.01 Ordering code includes: two 22 in. or two 24 in. linear LED boards and 40W araya5 Logic Module.0-10V; Bluetooth-enabled for iOS commissioning.

To implement the above configuration, the following items must be added to the order:2-wire power cable assembly: 28.030.001.0132” flat ribbon cable; 16-pin Tyco connectors at 0”, 24” and 32”: 28.031.001.01Reflector end caps (set of 2): 45.001.011.01





(45.001.011.01)






LTM2




(28.030.001.01)

50W ALM

22 in. linear board

55 inches Linear LED Array Kit: 80.001.094.01Ordering code includes: two 22 in. linear LED boards, one 11 in. linear LED board and 50W araya5 Logic Module.0-10V; Bluetooth-enabled for iOS commissioning.

To implement the above configuration, the following items must be added to the order:2-wire power cable assembly: 28.030.001.0132” flat ribbon cable; 16-pin Tyco connectors at 0”, 24” and 32”: 28.031.001.018” flat ribbon cable; 16-pin Tyco connectors at each end: 28.030.001.04Reflector end caps (set of 2): 45.001.011.01





(45.001.011.01)


<�:::i 0 0

11 in. linear board

32” flat ribbon cable

(28.031.001.01)


(28.031.001.04)

22 in. linear board





LTM2




(28.030.001.01)

60W ALM


(28.031.001.02)


66 inches Linear LED Array Kit: 80.001.095.01, OR72 inches Linear LED Array Kit: 80.001.202.01Ordering code includes: three 22 in. or three 24 in. linear LED boards and 60W araya5 Logic Module.0-10V; Bluetooth-enabled for iOS commissioning.

To implement the above configuration, the following items must be added to the order:2-wire power cable assembly: 28.030.001.0144” flat ribbon cable; 16-pin Tyco connectors at -20”, -12”, 0”, and 24”: 28.031.001.02Reflector end caps (set of 2): 45.001.011.01





(45.001.011.01)

22 in. or 24 in. linear board22 in. or 24 in. linear board





LTM2




(28.030.001.01)

70W ALM


(28.031.001.03)


77 inches Linear LED Array Kit: 80.001.096.01, OR83 inches Linear LED Array Kit: 80.001.204.01Ordering code includes: three 22 in. or three 24 in. linear LED boards, one 11 in. linear board and 70W araya5 Logic Module.0-10V; Bluetooth-enabled for iOS commissioning.

To implement the above configuration, the following items must be added to the order:2-wire power cable assembly: 28.030.001.0168” flat ribbon cable; 16-pin Tyco connectors at -34”, -26”, 0”, 26” and 34”: 28.031.001.03Reflector end caps (set of 2): 45.001.011.01





(45.001.011.01)

22 in. or 24 in. linear board22 in. or 24 in. linear board


<�:::i 0 0

11 in. linear board





LTM2



88 inches Linear LED Array Kit: 80.001.097.01, OR96 inches Linear LED Array Kit: 80.001.203.01Ordering code includes: Four 22 in. or four 24 in. linear LED boards and 80W araya5 Logic Module.0-10V; Bluetooth-enabled for iOS commissioning.

To implement the above configuration, the following items must be added to the order:2-wire power cable assembly: 28.030.001.0168” flat ribbon cable; 16-pin Tyco connectors at -34”, -26”, 0”, 26” and 34”: 28.031.001.03Reflector end caps (set of 2): 45.001.011.01





(28.030.001.01)

80W ALM


(28.031.001.03)



(45.001.011.01)

22 in. or 24 in. linear board22 in. or 24 in. linear board22 in. or 24 in. linear board





LTM2


88 inches Linear LED Array Kit: 80.001.097.01, OR96 inches Linear LED Array Kit: 80.001.203.01Ordering code includes: Four 22 in. or four 24 in. linear LED boards and 80W araya5 Logic Module.0-10V; Bluetooth-enabled for iOS commissioning.

Required accessories (ordered separately):2-wire power cable assembly: 28.030.001.0168” flat ribbon cable; 16-pin Tyco connectors at -34”, -26”, 0”, 26” and 34”: 28.031.001.03Reflector end caps (set of 2): 45.001.011.01 (four orders)

To implement 0-10V Control:7-wire control cable assembly: 28.002.002.01


To implement Lutron EcoSystem control:Lutron Control Card: 80.003.002.02

16.9 8-Foot Square-Shaped Linear Array Configuration Example


(28.030.001.01)


(28.031.001.03)





(45.001.011.01)

22 in. or 24 in.. linear board

80W ALM


(45.001.011.01)


(45.001.011.01)


(45.001.011.01)





LTM2


16.10 6-Foot U-Shaped Linear Array Configuration Example


(28.030.001.01)




(45.001.011.01)


60W ALM


(45.001.011.01)


(45.001.011.01)

66 inches Linear LED Array Kit: 80.001.095.01, OR72 inches Linear LED Array Kit: 80.001.202.01Ordering code includes: three 22 in. or three 24 in. linear LED boards and 60W araya5 Logic Module.0-10V; Bluetooth-enabled for iOS commissioning.

Required accessories (ordered separately):2-wire power cable assembly: 28.030.001.0144” flat ribbon cable; 16-pin Tyco connectors at -20”, -12”, 0”, and 24”: 28.031.001.02Reflector end caps (set of 2): 45.001.011.01 (three orders)

To implement 0-10V Control:7-wire control cable assembly: 28.002.002.01


To implement Lutron EcoSystem control:Lutron Control Card: 80.003.002.02


(28.031.001.02)


Lumenetix Inc.4742 Scotts Valley DriveScotts Valley, CA 95066877.805.7284www.erp-power.com

https://www.erp-power.com/

5 Logic Module Tunable Color Linear LED Arrays (LTM2) 24V DC … · 2020-06-18 · Color...

Documents

Transcript of 5 Logic Module Tunable Color Linear LED Arrays (LTM2) 24V DC … · 2020-06-18 · Color...