LifeIonizers.com/support 5 - Amazon S3 on the purchase of your new alkaline mineral water ionizer....

1LIFE MXL-5LifeIonizers.com/support

2LIFE MXL-5 LifeIonizers.com/support

Welcome to the LIFE Ionizers family!

Congratulations on the purchase of your new alkaline mineral water ionizer. We are grateful to our many customers for recognizing our efforts in providing the best water ionizer available!

Ionized Alkaline Mineral Water promotes good health with its superi-or hydration, mineralization, oxygenation and cellular detoxification. Our ionizers use a series of internal and external filtration systems and the finest-quality platinum-coated titanium plates, to create alkaline water with the highest anti-oxidant potential in the industry.

What do I need to know?

• Please read all safety warnings before the installation or operation of your LIFE Ionizer to ensure proper product usage.

• To receive warranty service, you must register your warranty online. Please see enclosed warranty card for detailed instructions.

• Refer to this manual when you have questions on adjustments and how to change your filters. We also have instructional videos and help guides online at LifeIonizers.com/support.

• Changing your filters is important! To ensure optimal perfor-mance and to guarantee your warranty, your ionizer has a new RFID Technology built into the internal filters which will give you a warning that your filter life is low and that you should replace your filter. If the filter life runs out, the ionizer will not function until the filter is changed. It’s important to have filters changed on time so the performance of your ionizer will continue.


Table of Contents

Safety Guide Product SpecificationsPackage ContentsImportant to RememberParts of the IonizerMXL-5 InstallationQuick Connect Fittings and TubingDisplay Overview Function Options MXL-5 Operation MethodInternal Filter ReplacementFilter Reset Indicators Citric Acid (Scaling) Cleaning FilterFiltration MediaPre-Filter ReplacementAcidic Cleaning Instructions & Routine MaintenanceCommon Problems and SolutionsOperation Warnings/Error MessagesHow Alkaline Water is MadeAlkaline/Acidic/Purified WaterUses of Ionized Alkaline/Acidic WaterPerformance Features Frequently Asked Questions

4 7 81012141617182324252628293031323334353839


Safety Guide

Power Plug

As with most electrical appliances, electrical parts in this ionizer are electrically live even when the switch is off.

• Power cord should not be touched with wet hands• Use only (110v) in the USA, Mexico and Japan. Most

other countries require (220v). The power cord cannot be altered from manufacturer’s specs.

• Do not crimp or staple the power cord• Power cord should be plugged directly into an

electrical outlet• Dusty or dirty electrical outlets may cause safety

issues• Bending, twisting, pulling or putting heavy objects

onto the power word may cause electrical problems including fire.

• If power cord, plug or electrical outlet are damaged, discontinue use immediately.

• Unplug the electric power when not in use for a long time (over 3 days)


Ionizer

• Place machine in an upright position only• Do not install this unit in direct sunlight or near a heater,

fireplace or other heat source• Do not place the machine in humid areas such as

bathrooms• If wall mounted, secure firmly and correctly• Do not use water with a temperature of over 95

degrees Fahrenheit or 35 degrees Celsius• This machine should not be repaired or otherwise

disassembled by any unauthorized person as it may cause electrical fire or shock and will void the manufacturer’s warranty

• Do not clean this machine by spraying the ionizer with water as it may cause electrical shock.

• Do not use benzene, thinner, or chemicals to clean the unit as it can damage the housing.

• Do not block the unit vent as it can cause overheating and/or electrical problems.

• Do not block the water passage or tubing• Do not place anything on the unit• Don’t shake or drop

the unit• If the ionizer

machine falls into water: 1. Unplug power cord from electrical outlet 2. Wipe the machine down and place in shaded area 3. Contact your LIFE Ionizer dealer


Ionized water

• If inexperienced with drinking Ionized Alkaline Water, users are encouraged to start with level 1

• When drinking Ionized Alkaline Water - Do not take prescription or other medications for approximately one hour before and after drinking water. Ionized alkaline water hydrates more efficiently, therefore will deliver more medication than tap water.

• Store Ionized Alkaline Water in an air-tight glass container and refrigerate for up to 2 days

• DO NOT DRINK ACIDIC WATER• Do not store Alkaline or Acidic water in metal containers,

although you can put alkaline water in the Water for LIFE Stainless Steel bottles as they are designed to maintain pH and ORP

• Aluminum and brass containers will be tarnished by alkaline and acidic water

• If not used for several days, run water through the unit for 1 to 3 minutes before starting

• If the machine will not be used for several days: 1. Unplug the power cord from the electrical outlet 2. Turn off the water valve to avoid leaking 3. Remove filters, drain and place in refrigerator in plastic bags. 4. Let water run on the “Purified Water” setting for at least 3-5 minutes before any operation


Product Specifications

Special features Fully convertible: counter-top to under counter

Cleaning function Advanced RADC Cleaning System

Display Full Color LED Display w/ Automatic Voice Prompting

Filtration Dual Internal, Custom Pre-filter

Flow Control Automatic

Power in watts Adjusts up to 250 watts

ORP Output up to -500 (Enhanced ORP at drinkable levels)

pH Output pH range from 5.5 up to 10.3

Protection Automatic Heat Sensor

Power System MAX Yield SMPS Power System™

Rated Voltage Dual voltage input compatibility 110/220 volts. All you need is the power plug or adapter. When plugged into the power source the unit automatically recognizes voltage.

Settings 1 Purified, 3 Acidic, 4 Alkaline

Warranty 7 Year Warranty

Dimensions 12.5” W | 15” H | 6.25” D

Plate Material Platinum over Industrial Titanium


Package Contents

Extra Fuse

1/4” Tubing Hose

User Manual

BTB Chemical

pH Color Chart

Reagent Drops(pH Test Drops)

Suction Cup

Located in the Power Switch at the bottom of the machine

Flexible Hose

Pull downDiverter Valve


10

9.0

8.0

7.0

6.0

5.0

4.0

Alkaline Water

Acid Water

Neutral

PH Tester Kit Instructions:

1. Place 1-2 ounces of water you are testing into a glass

2. Add 2-3 drops of Reagent Drops3. Stir water to observe the color

change4. Compare to “pH COLOR CHART”

to determine pH and acid levels.

When handling the pH test (reagent drops):1. Keep away from eye area. If eyes become irritated, flush

thoroughly and consult a doctor.2. If accidentally swallowed, drink water and consult a doctor.3. Store in an airtight container away from the reach of children.4. Drops are flammable. Keep away from children.

How to measure the pH of your water

A pH color chart and a bottle of Reagent Drops are included with your ionizer in case you would like to test the water from your new ionizer.


• You must run 2-3 gallons of water through the pre-filters before you connect them to the ionizer. To do this, install the pre-filters into their housings, connect a piece of tubing to the outlet con-nection on the pre-filter housing and run it into the sink so you can flush them out with water. This hydrates the filters and cleans them from any loose media. After you finish this procedure, con-nect your pre-filter back to your ionizer and run normally. This needs to be done every time you put in new pre-filters.

• The pre-filter housings must be replaced every 2 years.

SEE PAGE 14 FOR COUNTER TOP INSTALLATION INSTRUCTIONSSEE PAGE 16 FOR UNDER COUNTER INSTALLATION INSTRUCTIONS

Important to Remember

Pre-filter Installation & Maintenance

Ionizer Installation

• Plugs located on the bottom of the ionizer must be removed before installation.

• Do not overtighten the patch cable connection on the back of the ionizer when plugging in patch cable.

• Run the ionizer and check for leaks at all tubing locations from the Diverter Valve to the Ionizer itself before operating the unit.


Settings

• Flow rate must be set before adjusting or running your ionizer.• Set flow rate no higher than 2.5 liters per minute. Anything higher

could cause internal damage.• When adjusting the settings, the buttons must be pressed

quickly as failure to do so will result in booting you out of the program menu.

• The unit must be dispensing water before pressing the buttons.• Adjust the flow rate (LPM) by slowing down the water flow to

ionizer from the source water: - Cold Water Connect (for under undercounter units) - Faucet Diverter ( for countertop units)

• SEE PAGE 14 FOR COUNTER TOP INSTALLATION INSTRUCTIONSSEE PAGE 16 FOR UNDER COUNTER INSTALLATION INSTRUCTIONS

Ionizer Care

• Do not twist top of faucet. This will damage the faucet.• We recommend internal filters and pre-filters be changed

annually.• Citric acid cleaning filter should be used 3 to 4 times

per year.• Use cold water only with your ionizer


x x x - x x x x x - x x - x x

6

Inlet

Outlet

3 4 5

** Plugs must be removed before installation. See page 18 for Quick Connect Fittings and Tubing instructions.

Parts of the Ionizer

BACK

BOTTOM

1. First Filter Cover2. Wall Mount Screw Holes3. Speaker4. Bar Code and Serial Number5. Second Filter6. Under Counter Installation Plug/Connector

1. Source water inlet2. Acidic outlet3. On/Off Power Switch4. Fuse Box5. Power Plug

5

12

3

4


1. Control Panel2. Flexible Spout 3. LCD Panel

2

1

3

FRONT


LIFE MXL-5 Installation

Refer to diagrams on page15. (help video on LifeIonizers.com/support)

STEP 1: Unscrew the existing aerator from your faucet.

STEP 2: Use Teflon plumber’s tape on the threads. Make sure the black rubberwasher is inside the diverter valve before you screw it onto your faucet. This assures a proper seal. (Three different sized adaptors are included for non-standard sized faucets).

STEP 3: Unscrew the round nut from the side of the diverter valve. Place the1/4” tubing through the nut and over the opening. Press 1/4” tube on the barb fitting and screw the nut back onto the diverter valve over the tubing. Tubing should now fit snugly onto the diverter valve.

STEP 4: Run the other end of the 1/4” tubing that you attached to the diverter valve to the (IN) on the Pre-filter. Connect another piece of 1/4” tubing to the (OUT) on the Pre-filter. Run 2-3 gallons of water through the pre-filter before connecting them to the unit. This tube will then go to the inlet valve on the bottom of the ionizer in STEP 6.

STEP 5: Remove the plugs in the following manner: Lay the ionizer downon its back and you will see two white elbows extruding from the bottom of the machine. There will be an off-white collar around the base of the elbow (see page 18). Push in the collar against the face of the fitting. With the collar held in this position, you can extract the plug from the machine. It is sometimes helpful to use the back of a butter knife or screw driver to remove the plugs.

STEP 6: Insert the 1/4” tubing from the (OUT) on the Pre-filter to the inletvalve on the bottom of the ionizer using the quick connect instruc-tions on page 18. Insert another 1/4” tube in the outlet elbow on the bottom of the ionizer and run the other end into the sink securing it with the suction cup provided. Some units may contain waterDon’t be alarmed; we test units for quality before shipment.

STEP 7: Run the ionizer and check for leaks at all tubing locations from the Diverter Valve to the Ionizer itself before operating the unit.


Inlet

Outlet

DIVERTER CONNECTION

STEP 1:

STEP 2:

aerator

STEP 3:

round nut

1/4” tubing

Diverter valve

STEP 4:

elbows

STEP 5:

Bottom of ionizer

Diverter valve

inlet valve

outlet valve

Bottom of ionizer

suction cup

Pre-Filters

In Out

plugs (in green)

STEP 6:

NOTE: Run 2-3 gallons of water through the pre-filters before you connect them to the ionizer.

** Plugs must be removed before installation.

Pre-filters

Diverter valve

Option:Diverter Valve Adapter if needed for your type of sink.


Quick Connect Fittings and Tubing

Push the tubing into the quick connect. The collar (gripper ) has teeth which hold the tubing firmly in position while the “O” Ring provides a permanent leak proof seal.

Check the Seal: Pull on the tubing to see if the seal is secure. Check for leaks.

Ensure system is depressurized before removing fittings. Push in the collar against the face of the fitting. With the collar held in this position, the tube can be removed. The fitting can then be re-used.

collar

To ensure an optimal seal, tubing should be cut with the end square. An angled cut or distortion of the tubing will not provide an efficient seal and may cause leaks. Determine the length of tubing needed for the connection and cut the segment of tubing to the appropriate length.

push in collar

pull tubing out

quick connect

TO CONNECT:

TO DISCONNECT:


1. ON/OFF Button2. Alkaline Selector3. Purify Selector4. Acidic Selector5. Menu/Function6. Filter 1 Indicator7. Filter 2 Indication8. Filter 1/Life Indicator9. Filter 2/Life Indicator10. Operation Display Lamp11. Level Indicator12. Indicator Water Type (Alkaline/Acidic/Purify)13. pH Indicator

1211

9

8 13

10

4325 6 7 1

Display Overview


Function Options

AMPS AND LITERS PER MINUTE (LPM)

NOTE: the unit must be dispensing water before pressing the buttons.• Press and hold “FILTER 1” & “FILTER 2” simultaneously for 5 seconds in

order to enable the display of the Amps & LPM reading indicator light.

• Two numbers will then appear on the indicator.• The top number is the amps number followed by the digit A.• The bottom number is the Liters per Minute (LPM) followed by the

digit L.• Once the LPM is displayed, you can make the necessary adjustment

to the water flow in order to adjust the LPM to the unit. Adjust the LPM by slowing down water flow to ionizer from the source water: - Under Counter - Cold Water Connect - Counter Top - Faucet Adapter KEY NOTE: The slower the flow, the stronger the alkaline or acidic water is produced. We recommend that you set the machine between a flow of 1.5-3.0LPM.

• For strong 11+pH alkaline or 2.5 pH acid water, we recommend that the flow rate be set at 1.1-1.5 LPM. Do not set below 1.0 LPM because it will error out and display E1. NOTE: Your pH will be determined by your water source. If you’re on well water, your water is soft, or your TDS is too low, then you might need a remeneralizing cartridge or a pre-filter to add alkaline minerals so your unit can ionize properly.

NOTE: FLOW RATE MUST BE SET TO GET PROPER PH LEVELS.Recommended flow rate is 1.5-3.0 LPM

Amps & LPM (liters per minute) indicators


Recommended flow rate is 1.5-3.0 LPM

SOUND/VOLUME ADJUSTMENT (F10)

To enter the Volume Adjustment please do the following:• Press and hold the “MENU” button for 5 seconds.• Once you do this “VOL” will appear on the display and below that

it will show a number. • To increase volume, press and release the “FILTER 2” button, to

decrease the volume setting press and release the “FILTER 1” button.

MENU

FILTER 1FILTER 2


PH TESTING WITH DROPS

To test and to determine the pH of your water, you will have to select the level you are testing as well as combining the liquid reagent pH drops provided with the purchase of your ionizer with a sample of water gathered from your ionizer. 1. To begin this process, you will need a small clear glass of some sort. 2. Turn on your water ionizer and select the level of alkaline or acidic

water you will want to test. Please wait 10 seconds before collect-ing the water.

3. You will then need to add 2-3 liquid reagent pH drops to the glass first and collect 1 ounce (2 tbsp) of water from your ionizer.

4. After that you will need to compare the water you tested with the color ph chart provided with the pH drops.

5. You will need to adjust the amperage levels depending on your source water. We recommend you set water pH to ALK1-light blue/ALK2-dark blue/ALK3-light purple/ALK4-dark purple.

6. To do this follow the F-20 steps on the next page.

2-3 dropssmall clear glass 2 tbsp water

Add to glass:1.

+

ALK1ALK2ALK3ALK4

2. 3.

4. 5.

Adjust amperage levels by following the F-20 steps on the next page

6.

collect water


AMPERAGE ADJUSTMENT (F20) (help video on LifeIonizers.com/support)

To enter into the F20 you will need to do the following:

NOTE: The buttons must be pressed quickly as failure to do so will result in booting you out of the program menu. The unit must be dispensing water before pressing the buttons.

• Turn on ionizer and scroll through the alkaline and acid levels by pressing the “ALKALINE” or “ACID” button. Select the level you want to adjust.

• Press and hold the “MENU” & “FILTER 1” buttons simultaneously for 5 to 10 seconds (or until F20 appears on screen).

• F20 will appear on the display screen. • Below the F20, the amperage number will display. • To increase the amperage number, press and release the “FILTER 2”

button. The number will go up automatically. Release to stop.• To decrease the amperage number, press and release the

“FILTER 1” button. The number will go down automatically. Release to stop.

• Test the level of alkaline by adding 3-4 drops of the pH solution we recommend to 1 ounce of water. Set levels below to: ALK 1 - light blue ALK 2 - blue/purple ALK 3 - purple ALK 4 - dark purple

• If the color is not matching the pH chart, you may need to raise or lower the amperage until the desired color is correct.

• To save your adjustments, press the “PURIFY” button and the display screen will go back to its normal operation. NOTE: You cannot adjust the “PURIFY” selection.

• Repeat the process to adjust the other levels of alkaline or acid.• For optimum performance of the unit, you will need to clean

your ionizer with the CITRIC ACID CLEANING FILTER also known as the SCALING FILTER. We recommend using this cleaning cartridge 3-4 times a year depending on the hardness of your water.


FUNCTIONS F-30 AND AFTER

To enter F-30 and after functions you will need to do the following:• Press and hold the “MENU” & “FILTER 1” buttons simultaneously

for 5 seconds.• The machine will display F30 and the screen. • Press and release the “FILTER 2” button continuously to scroll

through the other F-functions.• Press the “MENU” button to select the function you want to adjust. • Press “FILTER 1” button to go down and “FILTER 2” button to go up.• Press “PURIFY” button to save the changes.

PLATE SELECTION (F-30)• Select number of plates (5,7,9,11 & 13) UNITS COME

PRE-SELECTED

LANGUAGE SELECTION (F-40)• Select preferred language. (English is the default language)

1- Korean 2- English 3- Chinese 4 -Russian 5 -Spanish

PH DISPLAY OPTIONS (F-50/F-51) (DO NOT CHANGE SETTINGS)• Default will show pH setting only• pH Ho - Fixed level (use this level)• pH En - Adjustable level

CLEANING (F-60) (reverses the electric power to clean the plates) (1) Washes beginning & end of water usage (2) Washes at the beginning only (default setting) (3) Washes at the end only (4) Does not wash at all

F-50 AND AFTER FOR ENGINEER USE ONLY

To show the power consumption and water flow information, press the “Menu” button and “Filter 1” button simlutaneously and hold down for about 8 seconds. NOTE: Water must be running through the ionizer.


Press the “ON/OFF” button. Then press the “ALKALINE” button and keep tapping that button until the desired alkaline level displays on the screen. The level indicator will display the level you selected. To STOP collecting water, press the “ON/OFF” button.

Press the “ON/OFF” button and then select the “PURIFIED” button to start dispensing filtered, purified water. To STOP collecting water, press the “ON/OFF” button.

Press the “ON/OFF” button. Then press the “ACIDIC” button and keep tapping that button until the desired acidic level displays on the screen. The level indicator will display the level you selected. To STOP collecting water, press the “ON/OFF” button.

LIFE MXL-5 Operation Method

Alkaline water discharge method

* Make sure the cold water is on and diverted to the ionizer.

Acidic water discharge method

Purified water discharge method

* Make sure to turn off the ionizer before turning off the water.

First time users who are not familiar with this water are recommended to start with Ionized Alkaline Water level 1 for two weeks, then adjust the level to Alkaline Water level 2 for two weeks, and then adjust again to Alkaline Water level 3 for daily drinking. This gradual adjustment will help your body get accustomed to the higher alkaline pH levels.


Internal Filter ReplacementFor installation video, go to www.lifeionizers.com/support and click the Next Generation filter replacement video.

How to Change the Filters

1. Push up on the filter cover to release it from the ionizer.

2. Turn the filter counter clockwise to release it out of the socket. (Open and close indicator will be on top of the filter).

3. Pull up on the filter to remove it from the ionizer.

4. Be sure to take the black cap off of the new filter.

Filter 2 Filter 1

5. For easy installation, lube new filters with a food safe lubricant like olive oil to the outside O-ring. This will help the filters turn more easily.

6. Line up the filter tabs and press the filter down into the socket.7. Turn the filter clockwise until it stops.

MAKE SURE THE FILTER NUMBER IS FACING YOU WHEN INSTALLED. IF NOT, THE IONIZER WILL NOT WORK.

8. Replace the filter cover.

IMPORTANT: When the unit shows 0060 on the filter counter, it will tell you to replace the filter. When the filter counter reaches 0000, the unit will not function until you replace the filter needed. It is best to have additional filters on hand so that you can replace the filters before this happens.

0060 or 6 liters left on filter life

0000 or no liters left on filter life

Filter 1Filter 2

Filter 1Filter 2


Filter Reset Indicators

• Select the “PURIFIED WATER” setting and let the water run for 2-3 minutes after any filter replacement .

• If the machine has not been used for a few days, let the water run for 2-3 minutes at the “PURIFIED WATER” setting before making Ionized Alkaline water for consumption.

• Consult with the installer or retailer on the purchase of filters if in question about usage or installation.

After changing FILTER 1, the unit will recognize that a new filter has been installed. The indicator will reset to 3000 automatically.

After changing FILTER 2, the unit will recognize that a new filter has been installed. The indicator will reset to 6000 automatically.

Filter 1 Indicator

(help video on LifeIonizers.com/support)

Tips After Filter Replacement:

Filter 2 Indicator


1 2 3

4 5 6

7 8 9

PURIFIED

NOTE: If the water dispersed from the spout is still slower than the waste water, the machine may need to be sent in for deep cleaning.

(Step by Step Installation Guide on LifeIonizers.com/support)

Citric Acid (Scaling) cleaning filter should be used 3 to 4 times per year. Cartridge is only good for one cleaning.

ON/OFF

Citric Acid (Scaling) Cleaning Filter


1. Turn off power to the ionizer by pressing the circle side of the power switch located at the bottom of the ionizer.

2. Release the #2 filter cover (located on the left side when looking at the back of the ionizer) by pushing up on the filter cover. Remove cover.

3. Remove the #2 filter by twisting the filter counter clockwise and then lifting it out of the ionizer.

4. Remove the clear plastic packaging and black cap from the bottom of the Citric Acid (Scaling) Cleaning Filter.

5. Before installing the filter, lube up the large outer O-ring with either olive oil or vaseline. Line up the 2 tabs on the filter to the filter base in the ionizer.

6. Once you have aligned the tabs on the filter with the ionizer, press down and twist the filter clockwise until it stops. Make sure the blue circle with filter name is facing out toward you. If not, the ionizer will not run.

7. Replace the cover and turn the power switch back on.

8. Apply water pressure, press the “ON/OFF” button and produce water for 15 seconds. The display will show “CLEAN” while doing this. Press the “ON/OFF” button to stop extraction. For counter top applications, remove the acidic tube from the sink and fasten it to the ionizer ensuring that the cleaning solu-tion will not leak out of the ionizer. Now let the unit sit for a minimum of 6-8 hours or for best results, overnight. The unit is full of a citric acid solution that will take many hours to break down the scale that has built up in your unit. Letting it sit in the unit for over a 6 hour period is okay and will not harm the ionizer.

9. Once the unit has sat for the recommended time, (leaving scaling filter in place) unfasten the acidic tube from the ionizer and place it back in the sink (for counter top applications) and then press the center “ON/OFF” button. Let the unit extract water for 3-5 minutes. This step will purge all of the citric solution, along with any scale, out of the machine.

The cleaning process is now complete. Remove the scaling filter and throw it way or recycle it and reinstall a #2 filter with the circled number facing out toward you.

NOTE: If you are putting in any new filters, do so after the cleaning.


Filtration Media

1. Thin Sediment filter Blocks fine sediments in water

2. Life CleanTech™ Filtration Reduces hard water deposits and mineral buildup

3. Activated Carbon Filter Anti-chlorine and anti-bacterial filtration

4. Easy-Notify Filter Change™ alerts with RFID technology Your water will always be fresh without the need to mark your calendars.

1. Thin Sediment Filter Blocks fine sediments in water

2. Vitamin C Ceramic Block® Chlorine and chloramine reduction

3. Activated Carbon Anti-chlorine and anti-bacterial filtration

4. KDF (Made in USA) VOC and heavy metal reduction

5. Easy-Notify Filter Change™ alerts with RFID technology Your water will always be fresh without the need to mark your calendars.

Filter 2

Filter 1


1. Shut off water supply at source (cold water connect or diverter valve). Turn on the ionizer to relieve water pressure. Shut off ionizer.

2. Disconnect 1/4” tubing from inlet and out-let from pre-filter. Press collar in the then pull on tubing to release.

3. Lay down the pre-filter and use the pre-filter wrench to loosen filter from housing. Slide pre-filter wrench from bot-tom to top. Twist pre-filter wrench coun-ter clockwise to loosen.

4. Remove filter housing from bracket. Discard old pre-filter. Install new pre-filter (Some pre-filters are directional. These will say “this side toward cap”).

5. Lube up large black O-ring located in filter housing next to the threads.

6. Install filter housing with filter onto the cap. Tighten with pre-filter wrench clockwise.

7. Repeat process if needed to your other filters.8. Connect inlet and outlet tubing.9. Apply water pressure.

10. Run ionizer on “PURIFY” mode for around 3-5 minutes to flush out pre-filter.

Pre-filter Replacement


Acidic Cleaning Instructions& Routine Maintenance

Many locations have excessive mineral content in the source water that can build up inside the ionizer over time and cause blockage. A routine acidic cleaning of the ionizer chamber will help maximize the life and performance of your ionizer by reducing the build-up of these minerals.

In areas with heavy mineral content, this is recommended once a week. It is also recommended to do this procedure in the evening as it takes several hours to be effective.

• Turn ionizer on by pressing ON/OFF (power) and set it on acid level 3• Once ionizer starts producing water, count to 15 • Press ON/OFF (power) to stop the ionizer from producing water• Let the water “soak” in the chamber overnight (12-24 hours)• Run the unit again on acid level 3 for 5 minutes to rinse the

minerals from the machine• Return the unit to normal operation

Our Citric Acid Cleaning Filter (available for purchase online) will be needed to clean the inter-nal workings of the machine. This procedure must be performed 3-4 times per year to keep warranty intact. See page 31 & 32 for instructions on how to do this.

Note:


Condition Possible Problem SolutionsThe power light is not on or the power switch doesn’t seem to work

• Unit may not be plugged in correctly

• Unit may be plugged into an outlet controlled by a switch

• Fuse at the bottom of the machine may be blown

• Make sure power plug is plugged into outlet correctly

• Plug unit into an outlet that is constantly ‘hot’

• Replace the fuse at the bottom of the unit

Water volume is low or doesn’t come out of the unit

• Angle valve adapter and/or cold water supply are turned off

• One or more of the water supply tubes is crimped

• House water pressure is too low

• Pre-filter and/or unit filters are blocked

• Make sure all water supply valves are open

• Check all hoses and tubes• Water pressure may be low for

many reasons (RO system, sprinkler system, etc) Call LIFE Ionizers Tech Support for assistance

• If unit has been used for 6 months or more, replace filters as needed

Tubing is leaking • Tube is not seated properly or there is a hole in the tubing

• Disconnect and reconnect tubing making sure it is seated 3/4 inches deep or replace tubing

Pre-filter is leaking • Tubing to pre-filter is not seated deeply enough

• O-rings inside the pre-filter are not seated correctly or are being crimped due to cover being on too tight

• Disconnect and reseat tubing at least 3/4 inches in to filter

• Disconnect tubing and unscrew cover. Make sure O-rings are seated properly

Water has an unpleasant odor or taste

• The internal filters may need to be replaced

• Water source requires a pre-filter or RO filter

• Call your dealer to place an order for new filters

• Call LIFE Ionizers for a water quality report for your area

Unit is making an unusual noise

• The problem is internal and requires a qualified technician

• Unplug the unit from the power source and call Technical Support

Ionizer is leaking • The problem is internal and requires a qualified technician

• Unplug the unit from the power supply and call Technical Support

Common Problems and Solutions


Operation Warnings/Error Messages

E1 : Water flow from ionizer is too low.- Turn the water pressure up.

E2 : Water flow from faucet is too high or the tubing from the INLET/OUTLET are swtched.- Turn water pressure down or ensure the tubings are in the right location.

E6: The Citric Acid Cleaning filter has expired.- Take Citric Acid filter out and re-install #2 filter.

E7: Either filter #1 or filter #2 are expired and counter displays “0000”.- Replace with a new filter and it the counter will reset on it’s own. The ionizer will not function until a new filter is installed.

E8: Either Filter #1 or Filter #2 is installed incorrectly.- See page 29 for proper way to install the filter.

For further help with the above error codes, or any additional error messages that appear on the LCD screen, please contact our technical support at 866-321-3116.

Error Codes:


How Alkaline Water is Made

1

2

Converts the existing mineral carbonates in tap water into mineral hydrates.

Splits alkaline minerals – calcium and magne-sium – from the carbon-ate in water using elec-tromagnetism.

3 Separates water into an alkaline stream and an acidic stream.

Alkaline Side:

• Higher pH• Antioxidant

Acidic Side:

• Lower pH• Oxidative

ChlorineSulfurFluorideHydrogen Ions

CalciumMagnesium

PotassiumHydroxide Ions

The alkaline water side of the ionizer attracts alkaline mineral ions, mostly calcium and magnesium.

Pure calcium and magnesium combine with water molecules by splitting them into a hydroxyl ion, and a hydrogen ion.

The hydroxyl ion combines with the minerals to form a solution of water and mineral hydrates - Calcium hydroxide and magnesium hydroxide.

Both of these mineral hydrates are more alkaline than the mineral carbonates they replace, so they raise the pH of the water making it more alkaline.

4

5

6

7


Alkaline/Acidic/Purified Water

Please note that water will come out of both spouts when dispensing water.

A) When the Alkaline button is pressed, Alkaline water will be dispensed from the top spout and acid water will be dispensed from the bottom spout.

B) When the Acid button is pressed, Acid water will be dispensed from the top spout and Alkaline water will be dispensed from the bottom spout.

C) When the purify button is pressed, purified water will be dispensed from the bottom and top spouts.

• 1. If the machine has not been used for several days, let the water run on the “Purified Water” setting for at least 3-5 minutes before any operation.

• First time users who are not familiar with this water are recommended to start with Ionized Alkaline Water level 1 for two weeks, then adjust the level to Alkaline Water level 2 for two weeks, and then adjust again to Alkaline Water level 3 for daily drinking. This gradual adjustment will help your body get accustomed to the higher alkaline pH levels

• Store Ionized Alkaline Water in an airtight glass container, or our special stainless steel bottle, and put it in a refrigerator for no longer than 2 days for maximum benefit. The first 12 hours after ionization the water is most effective.

Acidic water is not drinkable – DO NOT DRINK• Use acid water only for disinfecting, cleaning, plants and as a

face/skin toner.• Acidic water properties are the best 1-7 days after ionization if it

is put in an airtight glass container and kept refrigerated.

• It is best to drink purified water when taking medication. • Children: Use purified water when preparing baby food.

ALKALINE WATER

ACIDIC WATER

PURIFIED WATER


Uses for Ionized Alkaline/Acidic Water

Highly Ionized Alkaline Water: pH 11.0+Highly Ionized Alkaline Water is useful for cleaning and preparing food.

Food Preparation: Wash Vegetables and fruit.

Cleaning: Clean cutting boards with. Good for cleaning oil and tough grime from vents, as well as for general cleaning in the kitchen.

Stain Removal: The extra strength, absorption power will remove coffee, soy sauce and oil stains. Also great for getting out stubborn toilet bowl stains.

Dishes: Use less detergent when hand washing dishes. Save on water bills, as only one-third to one-forth of the usual amount of water is adequate cleaning and for rinsing with detergent.

Alkaline Water pH: 8.0-10.0For drinking, food preparation, watering plants, health maintenance.

Drinking: Drink at least eight 8 ounce glasses of water every day. Alkaline water is part of a healthy diet.

Food Preparation: Clean vegetables and fish. Enhance the flavor of broccoli, onions, etc. by pre-boiling them in Ionized Alkaline Water. Use less condiments and salt in your diet.

Rice: Use Ionized Alkaline Water for washing and cooking rice. The result is delicious and fluffy rice.

Tea: Taste and aroma are everything to many people. You will be surprised at the improved color, taste, and aroma. You can use less tea and still achieve a full rich taste.


Soups and Stews: Ionized Alkaline Water draws out the flavor of ingredients so they get tender and juicy. Therefore, less seasoning such as salt and soy sauce are needed. This water is good for people who want to reduce their salt intake.

Animals: Give purified water with food. Just like humans, animals should not drink alkaline water for an hour before, during, or an hour after meals.

Crafts: Excellent for dyeing cloths, as well as other craft projects. You will love the vibrant colors obtained when using this water.

Health: Through continuous use, the acidic tendency of your body can be gradually corrected to an Alkaline levels. Drink at least half your body weight in ounces in order to gradually change an acidic level to a slightly Alkaline one.

Neutral Water pH: 7.0Free of chlorine, rust and cloudiness. Clean water is delicious drinking water.

Children: Use purified water with a pH of 7.0 when preparing baby food.

Slightly Acidic Water pH: 6.0

Plants: Watering plants and flowers. Ionized Alkaline Water extends the freshness and life of plants. Ionized Alkaline Water with a pH level of 9.0 can also restore the health of sick plants. Ionized Alkaline Water stimulates germination and improves seeding development.


Acidic Water pH: 4.0-6.0

Face wash: The astringent properties of acidic water are effective in toning and firming your skin. Pat the skin and leave to dry. This water is also excellent as a toner after shaving.

Hair Care: Use this water to rinse your hair after shampooing. Reduces annoying tangles and brings out a radiant shine. Keep in a spray bottle and spray your hair and face when you’re out and about.

Bath Water: Add acidic water to your bath water to keep your tub free of bathtub rings. Bathing in this water gives your body a warm and comfortable feeling.

Pet Care: Spray your pet with this water and brush afterwards to obtain soft and shiny fur. Great for grooming your pet!

Rinse Cycle: Soaking with acidic water before the spin cycle will soften your clothes.

Cooking beans: Various types of beans, such as kidney beans and green peas, will cook to perfection. Just be careful not to overcook your beans. Acidic water will speed up the cooking time! This is energy saving water!

Fried Food: Fried food comes out nice and crispy if you rinse it in acidic water before frying.

Frozen food: Spray foods with acidic water when freezing so that the food, including fish and shrimp, does not lose its flavor when thawed.

Stains: To remove stains, grime and grease, leave to soak in water for 24 hours.

Dishes: Dishes and glasses come out sparkling clean.

Polishing: Polish mirrors, eyeglasses, glass objects and windows to a high sheen.

House Cleaning: Remove dirt from hardwood floors, ceramic tiles, etc. without leaving a sticky residue.


LIFE GRID Technology™ Drop-forged for greater durability, GRID plates increase the antioxidant power and pH of alkaline water by as much as 15%, like MESH plates, but GRID plates are far more durable. GRID plates are the toughest, longest lasting water ionizer plates made, they outlast flat, MESH, and Hybrid plates.

SMPS Power System- Combine GRID Technology™ with our advanced SMPS Power System (the same system used in High Definition Televisions) and your LIFE Ionizer® M series will outperform any other model in its class. The system generates up to 504 watts of power and it can be adjusted to compensate for hard water problems. SMPS Power means your system will run more efficiently provide consistent power, and will last longer.

UV Light System- LIFE UV Light Technology™ is an optional feature on our LIFE Ionizers®. UV light addresses cysts and bacteria as the water passes around the light inside the unit. UV Light is being used by major municipal water authorities such as New York City and Orange County, CA as added treatment to disinfect their water.

Performance Features


Frequently Asked Questions

Q: What should I expect from drinking Ionized Alkaline Water?

A: Everybody’s body is different, but typically new alkaline water drinkers say they see or feel effects in a month or two. You will notice a difference in taste: Ionized Water is much smoother tasting than conventional water. It makes better coffee, tea, juice, etc.

Q: Who should drink Ionized Alkaline Water?

A: People and pets can drink Ionized Alkaline Water.

Q: Is there anyone who should not drink Ionized Alkaline Water?

A: Some people must start by drinking very small amounts of Ionized Alkaline Water, such as 8 oz. of strength level 1 (one) Ionized Alkaline Water per day. This is especially true of the elderly who often have unfortunately allowed heavy metals and other toxins to accumulate in their bodies. Sometimes years of medication have accumulated in them. The health benefits for adults are well established through University studies and other studies done on a variety of health issues. Since no one has tested children we are making the following suggestions: Children 3 years and younger should drink water from the purified mode and then start on the low levels of Ionized Alkaline Water when they are older. Children between the ages of 4 years and 12 years should only drink Ionized Alkaline Water at strength level 1 (one) and strength level 2 (two). Children between the ages of 4 and 12 years of age should never drink Ionized Alkaline Water at strength level 3 (three) or strength level 4 (four).


Q: Should I take medication or supplements with Ionized Alkaline Water?

A: Do not take prescription or other medications for approximately one hour before and after drinking water. Ionized alkaline water hydrates more efficiently, therefore will deliver more medication than tap water. However, we highly recommend its use with vitamins, supplements, nutritional powders and other nutraceuticals because of its superior quality and enhanced absorption capabilities.

Q: Can a person become too Alkaline from drinking Ionized Alkaline Water?

A: People have been known to drink as much as 1 to 2 gallons of Ionized Water every day without a problem. It is rare for a person to acquire Alkalosis, the condition of being too Alkaline.

Q: Should I drink alkaline water when I eat?

A: No matter what type of water, it is not suggested to drink excessive amounts of liquids during meals. Small sips are suggested to cleanse the palette, but you should not gulp any type of water - alkaline, purified, etc.

Q: How much water should I drink and at what level?

A: At a minimum, you should drink half your body weight in ounces per day. For example, a person weighing 100 pounds should drink 50 ounces. You should start slow at strength Level 1 (one), drinking 1-3 glasses per day for the first week. You may increase the number of glasses per day during the first week if you do not notice any side effects. If you do not feel any flu-like symptoms at the end of the first week, move up to strength Level 2 (two). On strength Level 2 (two), drink 1-3 glasses per day for the first week. You may increase the number of glasses per day during the first week if you’re feeling good. On average, two to three weeks per level; work your way up to a 10.5 pH (strength Level 4 (four).


Q: Why do some people have flu like symptoms when first drinking Ionized Alkaline Water?

A: If you start drinking Ionized Alkaline Water at too high of a strength level (high pH level) then you might notice flu like symptoms. These symptoms are mild and they clear up in about a week. This effect is typically noticed by people whose bodies have accumulated toxins in them.

Q: How does Ionized Alkaline Water affect athletes?A: Many athletes alkalize their bodies prior to working out. Alkaline water can help. Additionally, drinking alkaline water during workouts is a great way to stay hydrated. Numerous studies conducted on athletes since the 1940s have demonstrated that even mild dehydration impairs performance. Dr. Peter L. Kopko, D.C. (Retired), recommends drinking 13 to 20 ounces (2-3 cups) of water 2 hours before exercise and 5 to 10 ounces (about 1-2 cups) every 15 to 20 minutes of exercise, depending on your total body weight.

Q: How long does Ionized Alkaline Water stay Ionized?

A: The Antioxidant (hydroxyl ions) will last approximately 18-24 hours. The Higher pH (Alkaline properties) will last approximately 1-2 weeks.

Q: Does Ionized Alkaline Water have any negative effects?

Absolutely none, as long as it is used properly. Only the Ionized Alkaline Water should be consumed. NEVER DRINK THE ACIDIC WATER.


Q: How does a water ionizer work?A: Your counter top Alkaline LIFE Ionizer® LIFE MXL-5 can be directly connected to a diverter valve at the end of your faucet. Connecting directly to your faucet takes about 10-15 minutes. Once connected your water ionizer uses a two step process to transform your tap water into refreshing, healthy alkaline water.

Your ionizer’s first task is to help filter out harmful components of the water with our built-in dual filter system. The LIFE Ionizer® achieves this by using multi-stage filters. In the second stage, the filtered water passes into the electrodialysis chamber, which is equipped with platinum-coated titanium plates. An electrical charge is introduced into this water. This is where the electrodialysis takes place.

The water is separated into two streams (acid and Alkaline) of Ionized water. The acid water (oxidized) makes up about 30% of the water and the Ionized Alkaline Water 70%. The Ionized Alkaline Water comes out of the faucet, and you use it for drinking or cooking.

The acid (oxidized) water comes out of a separate hose leading into the sink. The oxidation potential of the acid water makes it a good sanitizing agent, ideal for washing your hands, cleaning food or kitchen utensils, and treating minor wounds and eczema. Ionized acidic water is a miracle hair rinse!

The Chemistry of Ionized Water

A water ionizer splits the mineral carbonates found in tap water into alkaline and acidic parts. The minerals, mostly calcium and magnesium are alkaline, the carbonate, which is CO2 dissolved in water, is acidic.


Alkaline minerals produce positively-charged ions which gather at the negative electrode. These minerals chemically combine with hydroxyl ions taken from water molecules and form mineral hydrates. Carbonate produces negatively charged ions which gather at the positive electrode and combine with water to create a weak solution of carbonic acid.

Alkaline Ionized Water is drawn for drinking and cooking through the main stainless steel spout. Acidic water drains into the sink from a separate spout.

Q: How do I know when the filter needs replacing?

A: An LED or counter indicator on the front panel gives an indication of remaining filter life. Generally the 1st filter will last for about 8 months, the 2nd filter for about 12 months (when up to 2.5 gallons of water is produced per day), but this depends on the source of water and the amount of use. For example, if your tap water contains between 0.4 and 1.0 ppm (parts per million) of chlorine, a filter can last 12 months for one person’s use. If greater than 1.0 ppm, the filter may last 8 months. If you only use your ionizer on a limited basis, you will still need to change them annually so they are working correctly. NOTE: Your ionizer has a new RFID Technology built into the internal filters which will give you a warning that your filter life is low and that you should replace your filter. If the filter life runs out, the ionizer will not function until the filter is changed. It’s important to have filters changed on time so the performance of your ionizer will continue.


Q: Where is the serial number located?

A: On the back of the ionizer, you will see a bar code sticker. The serial number is located below the bar code.

Q: What should be done if the machine is not to be used for 7 days or more?

A: Remove the filter from the main body, wrap in plastic wrapping, and store in a refrigerator. Remove the power plug. When ready to use again, install the filter and run in the Ionizer in the ‘PURIFIED’ mode for approximately 3 minutes before using the water.

Q: What does it mean when water flows through the main body and it becomes warm?

A: At the start of water flow, warm water may flow out due to room temperature or heat from the main body during stoppage. This is not a malfunction. Use the machine after starting water flow.

Q: There are white substances on the bottom of my Alkaline Ionized water storage container. What are these?

A: This phenomenon is caused by the calcium mineral substances in Alkaline Ionized water. Particularly, if the carboxyl group (CO3) is present, it will bind to the calcium carbonate (Ca CO3), creating such substances. This is apparent evidence of electrolysis. Although it is safe to drink, wash the container - add one spoon of edible vinegar and water to the container, leave the container for approximately 1 hour, and wash the container.


Q: What is hard water?

A: According to the U.S. Geological Survey, more than 85 percent of the United States geography has hard water. Hard water forms when naturally occurring minerals enter water sources. Over time these minerals are absorbed by groundwater. The two most common types of minerals found in hard water are calcium and magnesium compounds. The Water Quality Association of the United States defines hard water as water containing dissolved hardness minerals above 1 GPG (grains per gallon). The most common hardness causing minerals are Calcium and Magnesium. Levels of hardness are classified as follows:

Soft Water - less than 1 GPG, Slightly hard - 1 to 3.5 GPG Moderately hard - 3.5 to 7 GPG Hard - 7 to 10.5 GPG Very Hard - 10.5 and higher GPG

Q: Why do I want to adjust the amperage on my Water Ionizer?

A: As you know, all water sources are not created equal. Your water source plays an important role on how your water Ionizer creates Ionized Alkaline Water. Being able to adjust the amperage will allow you to find the optimum pH for the best production of Alkaline Ionized water based on your water source.


Q: Do I need to hire a plumber to install the units?

A: Most people find it is not necessary to call a plumber for most standard installations. For custom installations, a plumber may be needed depending on the individual circumstances.

Q: What do I do if the filters are leaking?

A: It is important to note where on the filter it is leaking. Most leaking comes from fittings that are not seated properly. Reseat the tubing into the filter by pushing in firmly and then pulling back. It may be necessary to re-trim the end of the tubing to get a fresh surface. Make sure to shut off the water before working with the water supply lines.

Q: How do I set up the pre-filter unit?

A: The pre-filter is installed in the supply line on the ionizer. Quick connects are provided for your convenience. Simply push the tubing in the connector and it seals automatically. When installing the filter for the first time, it is suggested to let the filter fill with water for a few minutes before turning on the ionizer.

Q: How do I know what pre-filter I need?

A: A water report is necessary to determine what type of filter is needed. Well water may need to be tested by an independent water testing company. Please contact your sales representative and they will pull your Federal Water Report, analyze it, and recommend filters.


Q: How do I clean the internal plates?

A: Use the Citric Acid Cleaning Filter 3 to 4 times per year.

Q: What is the product warranty?

A: To validate your warranty, you must complete the warrantycard and return it or register online within 30 days of purchase. The warranty that is in effect at the time the machine is purchased is the one that is honored. Our warranty centers are in the US, Canada, Australia and Europe for your convenience. We are the oldest and largest distributors of Alkaline home, commercial and industrial water ionizers in North America with the finest quality service second to none. For Europe, Asia and Africa we have a service center in the UK. We value our customers and are very grateful for referrals. This is why we promote such a generous return policy and why we can do with confidence based on 18 years of growth and happy testimonials. Neglect includes using the unit in a matter inconsistent with the directions in the owner’s manual, as breakage resulting from dropping the unit or other carelessness. The international customer pays all international customs, government fees, levies and/or any other fees that are incurred. Warranties are non-transferable. The warranty is valid when all regular maintenance routines are followed. The following routine maintenance procedures will help keep your Ionizer running at the optimal performance level:• We recommend Internal filters be changed annually.• Citric acid cleaning filter should be used 3 to 4 times

per year.• Pre-filters should be changed annually.• Pre-filter housings should be changed every two years.

Following these easy steps ensures optimal performance and guarantees your Lifetime Warranty on part & labor.


If you buy a LIFE Ionizer® from an unauthorized seller/dealer, your warranty is void and will not be honored by life Ionizers®. Feel Free to contact us to confirm if the Dealer is an Authorized Dealer - 888 688 8889: Jeff or Kara

The LIFE M5 X NG has a Seven (7) years - full parts and labor warranty.

Q: What is your return policy?

A: We invite you to try out our new range of LIFE Ionizer® and enjoy the benefits for 60 days. We are so sure that you will be satisfied with your ionizer that we offer you a 60-day money back guarantee. If at any time in the first 60 days you wish to return your unit, we will give you a full refund, minus a 15% return fee and processing fee, as long as your ionizer is returned in as-new condition and in its original packing. “As-new condition” means the ionizer is not scratched, damaged or broken in any way and is returned with all hoses, connectors, parts, manuals and DVDs etc. The original shipping charges will be deducted and return shipping charges must be prepaid by the purchaser. No return can be accepted without our prior authorization. We will refuse unauthorized returns. There are no returns on merchandise purchased wholesale or through finance plans.

Q: What is your repair policy?

Warranties cover failures due to defects in materials and workmanship which occur during normal wear and tear. Warranty does not cover damage which occurs in return shipment, or failures which result from accident, misuse, abuse, neglect, mishandling, faulty installation, misapplication, improper insertion of consumables, set-up adjustments, maladjustment of consumer controls, improper operation or maintenance, alteration, modification, power line surge,


improper voltage supply, or service by anyone other than a LIFE Ionizer® authorized repair facility. LIFE Ionizer® will repair or replace any malfunctioning ionizer for the specified time frames disclosed above. If you are out of your warranty period, then labor is billed at $60/hr. Average repair time is less than one hour and in some cases there is no charge. Minimum charge is $0 to a maximum of $199 per occurrence. Customer is responsible for shipping and shipping charges to and from Repair Center.

Limits and Exclusions:There are no express warranties except as listed above. From the date of purchase the warrantor is not responsible for incidental or consequential damage; for damages arising out of the use of any unauthorized attachment; for damages resulting from the use of the product with a defective water faucet. All expressed and implied warranties, including warranties of merchantability and fitness for particular purpose, are limited to the applicable warranty period. The warranty is voided if parts used are not provided by LIFE Ionizer®. Company products are sold subject only to the applicable company standard printed warranty in effect at the time of sale and such warranty shall be in lieu of all other warranties expressed or implied. In addition, this equipment, technology and products have not been evaluated by the FDA, nor are they intended to treat, cure, mitigate, diagnose or prevent any illness or disease. The following technology is not intended to replace the advice of your family physician.


www.LifeIonizers.com/Support

6352 Corte Del Abeto, Suite H

Carlsbad, CA 92011

866.321.3116

760.431.8047

*When calling technical support please be prepared to give your ionizer serial number

located on the back of the unit.

Contact Us


rev 10-26-17

LifeIonizers.com/support 5 - Amazon S3 on the purchase of your new alkaline mineral water ionizer....

Documents

Transcript of LifeIonizers.com/support 5 - Amazon S3 on the purchase of your new alkaline mineral water ionizer....