'/5 6'%*0+%#. /#07#. - Pittco Architectural Metals, Inc. Manual/C1EMS114_09301… · ASTM...
Transcript of '/5 6'%*0+%#. /#07#. - Pittco Architectural Metals, Inc. Manual/C1EMS114_09301… · ASTM...
www.pittcometals.com
ARCHITECTURAL METALS, INC.
EMS 114
SEPTEMBER 2014
www.pittcometals.com
ARCHITECTURAL METALS, INC.
EMS 114
SEPTEMBER 2014
EMS 114
SEPTEMBER 2014
FEATURES
APPLICATIONS
SYSTEM PERFORMANCEDescription Test Method Allowed Achieved Test Report
Structural ASTM E 330 20 psf 17-4Air ASTM E 283 0.06 cfm/sq ft @ 6.24 psf 0.02 cfm/sq ft @ 6.24 psf 17-4Water (Static) ASTM E 331
AAMA 501.1None @ 4 psfNone @ 4 psf
None @ 4 psfNone @ 4 psf
17-417-4
CRF (est.) NFRC 500 N/A 11 17-7U Value * NFRC 100 N/A 1.09 17-7SHGC * NFRC 200 0.74 17-7
* 1/4" Clear, Annealed Monolithic Glass
N/A
N/A
FOR SPECIFIC PRODUCT APPLICATIONS PLEASE CONTACT YOUR PITTCO REPRESENTATIVE
EMS 114 is a center set flush glazed,non-thermal system that is 4 1/2" deep with a 1 3/4" wide sightline Glaze from the outside or inside Screw spline or shear block fabrication 1/8" , 1/4" , and 3/8" Glazing options Available in anodized and standard or custom painted finishes Readily available from stock
Storefront, Punched Openings, or Ribbon Windows Single span Integrated entrance framing to allow Pittco standard entrances
or other speciality entrances to be incorporated
Water (Dynamic)
www.pittcometals.com
ARCHITECTURAL METALS, INC.
EMS 114
SEPTEMBER 2014
FEATURES
1
www.pittcometals.com
ARCHITECTURAL METALS, INC.
EMS 114
SEPTEMBER 2014
EMS 114
SEPTEMBER 2014
BLANK PAGE
2
PRODUCT DESCRIPTION PAGE 4 TO 8. . . . . . . . . . . . . . . . . . . . . . . . .
1/4 SIZE DETAILS - NON THERMAL PAGES D1 TO D4. . . . . . . . . . . . . . . . .
DEADLOAD CHARTS PAGE S4. . . . . . . . . . . . . . . . . . . . . . . . . . . . SECTION PROPERTIES PAGE S5. . . . . . . . . . . . . . . . . . . . . . . . . .
ENTRANCE DETAILS PAGE D5. . . . . . . . . . . . . . . . . . . . . . . . . . . . WINDLOAD CHARTS PAGES S1 TO S3. . . . . . . . . . . . . . . . . . . . . . . . . . . .
EXPLODED VIEW PAGE 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
www.pittcometals.com
ARCHITECTURAL METALS, INC.
EMS 114
SEPTEMBER 2014
INDEX
3
● BASIC USES / RELATED USESFraming is designed for flush, center glazed storefront assemblyVertical mullions are open back aluminum members, with solid face and flush closure side plates forming tubular members for use onsingle spansHorizontal mullions are of hollow aluminum with removable glazing stopsCorners are configured for 90 and 135 degreesGlazing is single paneGlass may be transparent, opaque, or decorative typesFraming is intended for one story applicationsFramed assembly may be fitted to most rigid and stable framed opening assemblies
● PRODUCT ATTRIBUTES AND CHARACTERISTICSFraming and glazing stops are designed for glass and panelsWind pressure resistance and pressure equalization are standard within the frame assemblyWeep containment and condensate water collection and drainage to the exterior at concealed weeps are standardIntegral door frames are available
● SELECTION CRITERIAQuality, economy, and good performance are provided at a reasonable costFraming is designed for interior or exterior environments
● APPLICABLE STANDARDS, RELATED REFERENCESAA (Aluminum Association) - Designation System for Aluminum FinishesAAMA SFM-1-87 - Aluminum Storefront and Entrance ManualAAMA 501.1-05 - Standard Test Method for Water Penetration of Windows, Curtain Walls and Doors using Dynamic PressureAAMA 611-98 - Voluntary Specification for Anodized Architectural AluminumAAMA 2604-05 - Voluntary Specification, Performance Requirements and Test Procedures for High Performance Organic Coatings onAluminum Extrusions and PanelsAAMA 2605-05 - Voluntary Specification, Performance Requirements and Test Procedures for Superior Performing Organic Coatings onAluminum Extrusions and PanelsASTM A123/A123M - Standard Specification for Zinc (Hot-Dip Galvanized) Coatings on Iron and Steel ProductsASTM B209 - Standard Specification for Aluminum and Aluminum-Alloy Sheet and PlateASTM B209M - Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate [Metric]ASTM B221 - Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wires, Profiles, and TubeASTM B221M - Standard Aluminum-Alloy Extruded Bars, Rods, Wires, Profiles, and Tube [Metric]ASTM E283 - Standard Test Method for Determining Rate of Air Leakage Through Exterior Windows, Curtain Walls and Doors UnderSpecified Pressure Differences Across the Specimen
www.pittcometals.com
ARCHITECTURAL METALS, INC.
EMS 114
SEPTEMBER 2014
EMS 114
SEPTEMBER 2014
PRODUCT DESCRIPTION
4
ASTM E330 - Standard Test Method for Structural Performance of Exterior Windows, Skylights, Doors, and Curtain Walls by UniformStatic Air Pressure DifferenceASTM E331 - Standard Test Method for Water Penetration of Exterior Windows, Skylights, Doors, and Curtain Walls by Uniform Static AirPressure Difference
QUALITY, TESTS, CERTIFICATIONS, AND APPROVALSAir Infiltration: Maximum leakage of 0.02 cfm/sq ft. when measured in accordance with ASTM E283 at a test pressure of 6.24 psfStatic Water Leakage: No uncontrolled leakage, when measured in accordance with ASTM E331 at a test pressure difference of 4.00 psfDynamic Water Leakage: No uncontrolled leakage, when measured in accordance with AAMA 501.1 at a test pressure difference of 4.00psfStructural Performance: Maximum deflection less than 1/175 of the span length and no damage to the assembly, when measured inaccordance with ASTM E330 at a test pressure of 20 psf
● PACKAGING, HANDLING, AND PROTECTION INSTRUCTIONSPackaged in specially designed heavy cartons or shipped pre-fabricated and assembled
● SPECIAL WARRANTYOne (1) year
● LIMITATIONSNot thermally broken
Glazing is monolithic Framing is limited to applications of one story in height
● SAFETY PRECAUTIONSNormal precautions required
● AVAILABILITYFraming is available in all regions of USA - refer to Internet web site for locations and addresses of distributors
● COSTCost varies with elevation, configuration and finish desired
www.pittcometals.com
ARCHITECTURAL METALS, INC.
EMS 114
SEPTEMBER 2014
PRODUCT DESCRIPTION
5
PRODUCT PROPERTIES● MATERIAL, COMPOSITION AND DESIGN
Aluminum: 6063-T6 alloy and temper, to ASTM B221 or ASTM B221MFasteners: Stainless steel, or zinc plated carbon steelPerimeter Anchors: Aluminum, or steel that will be isolated from aluminum componentsGlazing Gaskets: Wedge-type, Ethylene Propylene Diene Monomer (EPDM) rubber with non-stretch cordGlass Stops: Snap-in type
● SHAPE AND DIMENSIONSFrame Size: 1-3/4 x 4-1/2 inchGlass Edge Bite: 5/16 inch horizontally (8mm) and 1/4 inch verticallyGlazing Thickness Accepted: 1/8 inch, 3/16 inch, 1/4 inch, 5/16 inch, 3/8 inch
● SHOP FABRICATION AND ASSEMBLYProvide for flush glazing on all sides with no projecting stopsConfigurations:■ Two-piece snap together mullions■ Solid tubular mullions, assembled with specially designed shear block clipsAccessories:■ Expansion Mullions■ Corner Mullions■ Open Back Perimeter Members■ Integral Door Frames■ Flashing, Subsills■ Head Receptor■ Heavy Duty Mullions■ Standard Steel Reinforcing Available
● COLORS AND TEXTURES■ Architectural anodic coating, in accordance with AAMA 611;
o Aluminum Association Designation.□ AA-M10C22A31 - Class II - (Pittco #42 Clear)□ AA-M10C22A41 - Class I - (Pittco #43 Clear)□ AA-M10C22A44 - Class I - (Pittco #59 Champagne)□ AA-M10C22A44 - Class I - (Pittco #60 Light Bronze)□ AA-M10C22A44 - Class I - (Pittco #61 Medium Bronze)□ AA-M10C22A44 - Class I - (Pittco #62 Dark Bronze)□ AA-M10C22A44 - Class I - (Pittco #63 Black)
www.pittcometals.com
ARCHITECTURAL METALS, INC.
EMS 114
SEPTEMBER 2014
EMS 114
SEPTEMBER 2014
PRODUCT DESCRIPTION
6
■ Architectural organic coating, in accordance with AAMA 2604 (50% Kynar 500®);o Finish of Exposed Aluminum shall be compliant with the performance standards set forth in AAMA Specification 2604, High
Performance Organic Coatings on Aluminumo Type: Factory Applied, High Performance, 50% Polyvinylidene Fluoride (PVDF) Coating formulated by a licensed paint
manufacturer, and applied by Paint Manufacturer's Warranty-Approved Applicatoro Pretreatment: Applicator to pre-treat the aluminum with solutions to remove organic and inorganic surface soils, remove residual
oxides, followed by a Chrome Phosphate or Chromate Coating to ensure adhesion to the aluminumo Specify color code, e.g. UC 40577(Duranar Black)
■ Architectural organic coating, in accordance with AAMA 2605 (70% Kynar 500®);o Finish of Exposed Aluminum shall be compliant with the performance standards set forth in AAMA Specification 2605, Superior
Performing Organic Coatings on Aluminumo Type: Factory Applied, High Performance, 70% Polyvinylidene Fluoride (PVDF) Coating formulated by a licensed paint
manufacturer, and applied by Paint Manufacturer's Warranty-Approved Applicatoro Pretreatment: Applicator to pre-treat the aluminum with solutions to remove organic and inorganic surface soils, remove residual
oxides, followed by a Chrome Phosphate or Chromate Coating to ensure adhesion to the aluminumo Specify color code, e.g. UC 40577(Duranar Black)
● PREPARATION WORKEnsure openings are of proper size, and are plumb, square, level and in the proper location and alignment
● INSTALLATIONAlign installed assembly plumb and level, free of warp or twistMaintain dimensional tolerances, aligning with adjacent workSeal joints between framing and building structure watertightFollow guidelines in Pittco Fabrication, Sealant and Erection Brochure
● START-UP AND OPERATIONNot Applicable
● OWNER'S MAINTENANCE INSTRUCTIONSWash surfaces with warm water and mild soap; wipe clean, at least once a year
www.pittcometals.com
ARCHITECTURAL METALS, INC.
EMS 114
SEPTEMBER 2014
PRODUCT DESCRIPTION
7
Corporate IdentificationPittco Architectural Metals, Inc
1530 Landmeier RoadElk Grove Village, Illinois 60007Tel: (847) 593-3131Fax: (847) 593-9946Toll-Free: (800) 992-7488Internet: http://www.pittcometals.comE-mail: [email protected]
Technical Services AvailableToll-Free: (800) 992-7488
Classification and FilingMasterFormat
Subset of Section 08410 - Metal Framed StorefrontsUniFormat
Section B2030 - (exterior entrance frames) or C1020 (interior entrance frames)
www.pittcometals.com
ARCHITECTURAL METALS, INC.
EMS 114
SEPTEMBER 2014
EMS 114
SEPTEMBER 2014
PRODUCT DESCRIPTION
8
www.pittcometals.com
ARCHITECTURAL METALS, INC.
EMS 114
SEPTEMBER 2014
EXPLODED VIEW
9
www.pittcometals.com
ARCHITECTURAL METALS, INC.
EMS 114
SEPTEMBER 2014
EMS 114
SEPTEMBER 2014
BLANK PAGE
10
3
4
5
1 2
SCREW SPLINE SHEAR BLOCK
2VERTICAL
1JAMB
3HEAD
4HORIZONTAL
5SILL
2VERTICAL
1JAMB
3HEAD
4HORIZONTAL
5SILL
17-452 (JAMB)20-168 (PERIMETER FILLER)
17-452 (JAMB)17-480 (GLAZING FILLER)
17-452 (JAMB)20-168 (PERIMETER FILLER)
17-452 (JAMB)17-480 (GLAZING FILLER)
17-452 (HEAD)20-168 (PERIMETER FILLER)
17-471 (HORIZONTAL)17-484 (GLASS STOP)
17-466 (SILL)17-484 (GLASS STOP)20-168 (PERIMETER FILLER)
17-452 (HEAD)20-168 (PERIMETER FILLER)17-911 (SHEAR BLOCK)
17-471 (HORIZONTAL)17-484 (GLASS STOP)17-910 (SHEAR BLOCK)
17-466 (SILL)17-484 (GLASS STOP)20-168 (PERIMETER FILLER)17-910 (SHEAR BLOCK)
www.pittcometals.com
ARCHITECTURAL METALS, INC.
EMS 114
SEPTEMBER 2014
TYPICAL FRAMING DETAILS (Outside Glazed)
D1
3
4
5
1 2
SCREW SPLINE SHEAR BLOCK
2VERTICAL
1JAMB
3HEAD
4HORIZONTAL
5SILL
2VERTICAL
1JAMB
3HEAD
4HORIZONTAL
5SILL
17-452 (JAMB)20-168 (PERIMETER FILLER)
17-452 (JAMB)17-480 (GLAZING FILLER)
17-452 (SILL)20-168 (PERIMETER FILLER)
17-471 (HORIZONTAL)17-484 (GLASS STOP)
17-466 (HEAD)17-484 (GLASS STOP)20-168 (PERIMETER FILLER)
17-452 (JAMB)20-168 (PERIMETER FILLER)
17-452 (JAMB)17-480 (GLAZING FILLER)
17-452 (SILL)20-168 (PERIMETER FILLER)17-911 (SHEAR BLOCK)
17-471 (HORIZONTAL)17-484 (GLASS STOP)17-910 (SHEAR BLOCK)
17-466 (HEAD)17-484 (GLASS STOP)20-168 (PERIMETER FILLER)17-910 (SHEAR BLOCK)
www.pittcometals.com
ARCHITECTURAL METALS, INC.
EMS 114
SEPTEMBER 2014
EMS 114
SEPTEMBER 2014
TYPICAL FRAMING DETAILS (Inside Glazed)
D2
19-047
2 PIECE NO POCKET CORNER 1 POCKET CORNER
2 POCKET CORNER 90° CORNER(SCREW SPLINE OR SHEAR BLOCK FABRICATION)
90° CORNER(SHEAR BLOCK FABRICATION ONLY)
3 POCKET CORNER 4 POCKET CORNER 135° CORNER
19-047
17-261
17-261
17-260
17-261 17-262
19-047
17-261
17-262 17-262
17-262
17-4
62
17-480
17-480
19-047
17-261
16-705
412" x 41
2" TUBE
ADJUSTABLE MULLION(ADJUSTABLE FROM 0 TO 90 DEGREES)
17-47717-476
www.pittcometals.com
ARCHITECTURAL METALS, INC.
EMS 114
SEPTEMBER 2014
CORNER DETAILS
D3
20-095
20-097
STANDARD MULLION w/OPTIONAL STEEL
16-501
HEAVY WALL MULLION HEAVY WALL MULLIONw/
OPTIONAL STEEL
TUBULAR MULLION EXPANSION MULLION
FULL LENGTHFLAT FILLER
SNAP INPOCKET FILLER
SLIDE INDOOR STOP
(not for use on hinge side)
HEAD RECEPTOR STANDARD SILL FLASHING
412 " x 41
2" HORIZONTAL 412" SILL NARROW SIDELITE BASE
17-452
17-480
17-463
17-480
16-500
17-340
17-208
17-208
17-463
17-480
19-168
17-015 17-159
20-10119-102
19-152
20-095
19-096 19-096
17-479
19-096 19-096
OPTIONAL SILL FLASHING
16-142
30-105
17-021
30-11730-117
www.pittcometals.com
ARCHITECTURAL METALS, INC.
EMS 114
SEPTEMBER 2014
EMS 114
SEPTEMBER 2014
MISCELLANEOUS DETAILS
D4
1TRANSOM HEAD
2DOOR HEAD
3BOTTOMRAIL
17-154 (TRANSOM HEAD)34-969 (SHEAR BLOCK)17-198 (GLASS STOP)
SINGLE ACTING
1
2
3
76
54
10
3
98
DOUBLE ACTING
SINGLE ACTINGDOOR JAMBS
DOUBLE ACTINGDOOR JAMBS
10SINGLE ACTING
HEADER
10DOUBLE ACTING
HEADER
617-333 OR 17-332
(MULLION)w/17-002 POCKET ADAPTER
TRANSOM JAMBSTransom area for both double or single acting doors withglass surround. Jambs above transom bar are routed outto accept glass holding insert with or without steel reinforcing.
817-332 (MULLION)
917-332 (MULLION)
417-333 (MULLION)
517-333 (MULLION)
717-333 OR 17-332
(MULLION)w/17-002 POCKET ADAPTER
16-713 (TRANSOM HEAD)34-969 (SHEAR BLOCK)14-088 (SASH)
17-154 (TRANSOM HEAD)34-969 (SHEAR BLOCK)
16-713 (TRANSOM HEAD)34-969 (SHEAR BLOCK)
17-452 (HEAD)20-168 (PERIMETER FILLER)
www.pittcometals.com
ARCHITECTURAL METALS, INC.
EMS 114
SEPTEMBER 2014
ENTRANCE DETAILS
D5
www.pittcometals.com
ARCHITECTURAL METALS, INC.
EMS 114
SEPTEMBER 2014
EMS 114
SEPTEMBER 2014
BLANK PAGE
D6
SYSTEM ANALYSIS CRITERIA:
DEFLECTION LIMITS: L/240 + 1/4" FOR SPANS GREATER THAN 13'-6"
CODES AND SPECIFICATIONS VARY, NO SINGLE LITE OF GLASS SHALL DEFLECT MORE THAN 3/4"
L/175 FOR SPANS LESS THAN 13'-6"
LATERAL BRACING OR HORIZONTAL MEMBER SPACING: 48" O.C. (MAXIMUM)
SECTION EVALUATED PER 2005 ALUMINUM DESIGN MANUALSIMPLE SPAN CONDITION
ALUMINUM: 6063-T6
17-45217-480
A = 15 PSFB = 20 PSFC = 25 PSFD = 30 PSFE = 40 PSF
17-452 17-480
WITH 16-500 STEEL
A
B
C
D
E
A
B
C
DE
(FOR HORIZONTAL SPACING GREATER THAN 48" CONTACT PITTCO ENGINEERING)
www.pittcometals.com
ARCHITECTURAL METALS, INC.
EMS 114
SEPTEMBER 2014
WINDLOAD CHARTS
S1
A = 15 PSFB = 20 PSFC = 25 PSFD = 30 PSFE = 40 PSF
17-46317-480
17-463 17-480
WITH 16-501 STEEL
A
B
C
D
E
A
B
C
D
E
SYSTEM ANALYSIS CRITERIA:
DEFLECTION LIMITS: L/240 + 1/4" FOR SPANS GREATER THAN 13'-6"
CODES AND SPECIFICATIONS VARY, NO SINGLE LITE OF GLASS SHALL DEFLECT MORE THAN 3/4"
L/175 FOR SPANS LESS THAN 13'-6"
LATERAL BRACING OR HORIZONTAL MEMBER SPACING: 48" O.C. (MAXIMUM)
SECTION EVALUATED PER 2005 ALUMINUM DESIGN MANUALSIMPLE SPAN CONDITION
ALUMINUM: 6063-T6
(FOR HORIZONTAL SPACING GREATER THAN 48" CONTACT PITTCO ENGINEERING)
www.pittcometals.com
ARCHITECTURAL METALS, INC.
EMS 114
SEPTEMBER 2014
EMS 114
SEPTEMBER 2014
WINDLOAD CHARTS
S2
17-340
17-20817-208
A
B
C
D
E
A
B
C
D
E
SYSTEM ANALYSIS CRITERIA:
DEFLECTION LIMITS: L/240 + 1/4" FOR SPANS GREATER THAN 13'-6"
CODES AND SPECIFICATIONS VARY, NO SINGLE LITE OF GLASS SHALL DEFLECT MORE THAN 3/4"
L/175 FOR SPANS LESS THAN 13'-6"
LATERAL BRACING OR HORIZONTAL MEMBER SPACING: 48" O.C. (MAXIMUM)
SECTION EVALUATED PER 2005 ALUMINUM DESIGN MANUALSIMPLE SPAN CONDITION
ALUMINUM: 6063-T6
(FOR HORIZONTAL SPACING GREATER THAN 48" CONTACT PITTCO ENGINEERING)
A = 15 PSFB = 20 PSFC = 25 PSFD = 30 PSFE = 40 PSF
www.pittcometals.com
ARCHITECTURAL METALS, INC.
EMS 114
SEPTEMBER 2014
WINDLOAD CHARTS
S3
SYSTEM ANALYSIS CRITERIA:
SECTION EVALUATED PER 2005 ALUMINUM DESIGN MANUALSIMPLE SPAN CONDITION
ALUMINUM: 6063-T6HORIZONTAL OR DEADLOAD LIMITATIONS ARE BASED UPON 1/8" MAXIMUM ALLOWABLE DEFLECTION WITH 1" THICK INSULATED GLASS
A = SETTING BLOCKS AT 1/8 POINTSB = SETTING BLOCKS AT 1/4 POINTS
17-471 (HORIZONTAL)17-484 (GLASS STOP)
17-466 (HORIZONTAL)17-480 (GLAZING FILLER)17-484 (GLASS STOP)
AB
AB
www.pittcometals.com
ARCHITECTURAL METALS, INC.
EMS 114
SEPTEMBER 2014
EMS 114
SEPTEMBER 2014
DEADLOAD CHARTS
S4
www.pittcometals.com
ARCHITECTURAL METALS, INC.
EMS 114
SEPTEMBER 2014
SECTION PROPERTIES
S5