4700 SERIES - Sterlco® – Steam Control Products
Transcript of 4700 SERIES - Sterlco® – Steam Control Products
Technical Specifications Sterlco® 4700 Series Condensate Units set new
standards of performance. Reliable and efficient, each
unit features heavy-duty cast iron receivers for long
operating life.
In addition, 3450 RPM motors assure maximum efficiency
while maintaining minimum motor horsepower. Available
in a wide range of sizes, these U.S. made units have just
the right accessories and options to meet your unique
needs.
Standard Features
• Heavy-duty cast iron receivers
• Simplex or duplex construction
• Stainless steel fitted centrifugal pumps
• Energy efficient 3450 RPM motors
• Automatic venting
• Carbon ceramic pump seal (300°F) with EPDM elastomers
• Heavy-duty float switch
• Wide range of options and accessories
Optional Features
• Mechanical and electric alternators for duplex units
• Gauge glass
• Thermometer
• Isolation valves
• Special motor construction, such as totally enclosed, washdown duty and explosion-proof is available
• 75 & 120 gallon tanks are available
• Elevated tanks are available
• Complete NEMA 12 Control Panel
Features
Steam Traps | Condensate | Boiler Feed | Valves | Strainers | Pumps
2900 South 160th Street, New Berlin, WI 53151 | P: 1.262.641.3808 E: [email protected] W: www.sterlco.com
4700 SERIESCondensate Units - Cast I ron Tank
Product Features
Control Panel
Motors:
Heavy-duty, ball-bearing, close-
coupled pump motors with stainless
steel shaft. 3450 RPM for greater
efficiency and more economical
operation.
Float Switch:
Two-pole, drip proof case, stainless
steel float and float rod, double-
break silver-to-silver contacts. Float
travel adjustment is easy, visible and
accessible.
Automatic Venting:
Provides for efficient operation and
long life by venting air and flushing
seal area.
Large Tanks:
Plenty of capacity for maximum
rating of pump. Return inlet is low.
Occupies a minimum of floor space.
Impeller:
Made of stainless steel for long life.
Efficient design provides maximum
capacity, minimum motor load.
Inducer:
Made of stainless steel for long
life. Raises the inlet pressure by
an amount sufficient to prevent
cavitation.
Pump seal (A):
Features the ultimate in ceramic
technology for exceptionally
long life. Seal is carbon ceramic
with EPDM elastomers. Rated for
temperatures up to 300°F.
Isolation Valve (B):
Optional on 4700 Series Condensate
Units. Allows removal of pump
without draining the tank.
Complete NEMA 12 Control Panel (Optional)
• Motor Circuit Protector
• HOA Selector Switch
• External Reset
• Control Circuit Transformer
• Pilot Light (pump running)
• Removable Mounting Plate and Terminal Strip in a Single NEMA 12 Enclosure
• Mounted and Wired with Single Point Power Connection.
A B
Inside view of control panel
Elevated Unit
2900 South 160th Street, New Berlin, WI 53151 | P: 1.262.641.3808 E: [email protected] W: www.sterlco.com
4700 SERIES
4700 Series Engineering and Capacity Data
Capacity Sq. Ft. EDR
Discharge Pressure PSI
Pump Capacity,
GPM
MotorHP
Rec. Capacity, Gallons
Unit Model Number Shipping Weight, lbs.
Simplex Duplex Simplex Duplex
2,0004,0006,0008,000
2036912
1/21/21/21/2
661515
4722-K4724-K4726-K4728-K
--
4726-KD4728-KD
150150260260
--
295295
10,00015,00020,000
2015
22.530
1/21/23/4
152436
47210-K47215-K47220-K
47210-KD47215-KD47220-KD
260300410
295335445
25,00030,000 20 37.5
453/41
3636
47225-K47230-K
47225-KD47230-KD
350355
420430
40,000 20 60 1-1/2 50 47240-K 47240-KD 420 500
50,000 20 75 1-1/2 50 47250-K 47250-KD 425 510
2,0004,0006,0008,00010,000
30
3691215
3/43/43/43/41
66151515
4732-K4734-K4736-K4738-K47310-K
- -
4736-KD4738-KD47310-KD
165165295295300
--
360360365
15,00020,000 30 22.5
3011
2436
47315-K47320-K
47315-KD47320-KD
305355
380430
25,00030,000 30 37.5
451-1/21-1/2
3636
47325-K47330-K
47325-KD47330-KD
355360
430440
40,000 30 60 2 50 47340-K 47340-KD 425 510
50,000 30 75 2 50 47350-K 47350-KD 435 525
2,0004,0006,0008,00010,000
40
3691215
11
1-1/21-1/2 1-1/2
66151515
4742-K4744-K4746-K4748-K47410-K
--
4746-KD4748-KD47410-KD
170170295295295
--
360360360
15,00020,000 40 22.5
301-1/21-1/2
2436
47415-K47420-K
47415-KD47420-KD
310360
390440
25,00030,000 40 37.5
4522
3636
47425-K47430-K
47425-KD47430-KD
360365
440450
40,000 40 60 3 50 47440-K 47440-KD 425 510
50,000 40 75 3 50 47450-K 47450-KD 435 525
2,0004,0006,0008,00010,000
50
3691215
1-1/21-1/21-1/21-1/2
2
66151515
4752-K 4754-K4756-K4758-K47510-K
--4756-KD4758-KD47510-KD
175175315315315
--395395395
15,00020,000 50 22.5
3023
2436
47515-K47520-K
47515-KD47520-KD
330370
415460
25,00027,000 50 37.5
4033
3636
47525-K47527-K
47525-KD 47527-KD
370370
460460
Sample Specification
Furnish and install, where indicated on plans, a Sterling 4700 Series (simplex or duplex) condensate unit(s), having a capacity of ___________ sq. ft.
E.D.R.___________ GPM against a discharge pressure of ___________ PSI. The receiver shall have a capacity of ___________ gallons and be of heavy-duty
cast iron construction. Pump(s) shall be of the centrifugal type with one-piece enclosed stainless steel impeller, stainless steel inducer, cast iron hous-
ing, high temperature (300°F) mechanical seal and stainless steel motor shaft. The float switch shall be two-pole with plastic case, stainless steel float
and shaft, and double-break silver contacts. An optional inlet “Y” or basket strainer is recommended for installation on the tank return inlet for pump
protection. The motor(s) shall be vertical, 3450 RPM, ___________ phase, ___________ volt, 60 cycle, ___________ H.P. The complete unit is to be factory
assembled and tested prior to shipment.
Specifications
2900 South 160th Street, New Berlin, WI 53151 | P: 1.262.641.3808 E: [email protected] W: www.sterlco.com
4700 SERIES
Product Diagrams
2900 South 160th Street, New Berlin, WI 53151 | P: 1.262.641.3808 E: [email protected] W: www.sterlco.com
4700 SERIES
3.13
8.13 10.63
10.75
1.256.31
.13FOOT PAD 6.31
26.97
1" NPTOVERFLOW
2" NPTPROCESS RETURN
3/4" NPTDRAIN
12.88
LIFTING EYES(OPTIONAL)
FLOAT SWITCH
THERMOMETER(OPTIONAL)
ISOLATION VALVE(OPTIONAL)
GAUGE GLASS(OPTIONAL)
12.63
1.25
3.696.94
3.53
16.16
GATE VALVE, CHECK VALVE,AND PRESSURE GAUGE(OPTIONAL)
1-1/2" NPTPUMPDISCHARGE
1" NPTVENTS
16.00
16.00
REMOTE MOUNTEDCONTROL PANEL(OPTIONAL)
4700 "K" SERIES CONDENSATE UNIT6 GALLON SIMPLEX
RECEIVER MATERIAL: CAST IRON
4700SER.K.CDSN.6
LH SIDE VIEW
Product Diagrams
2900 South 160th Street, New Berlin, WI 53151 | P: 1.262.641.3808 E: [email protected] W: www.sterlco.com
4700 SERIES
H I A
3.13
C
P
16.00
16.00
THERMOMETER(OPTIONAL)
CONTROL PANEL(OPTIONAL)
CAN BE MOUNTEDREMOTELY
FLOAT SWITCH ORALTERNATOR
GAUGE GLASS(OPTIONAL)
GATE VALVE, CHECK VALVE,AND PRESSURE GAUGE
(OPTIONAL)
J
K
3.50
L
O
N
B
M
Q NPT VENT
1-1/2" NPTPUMPDISCHARGE
DUPLEX PUMP
BLANK OFF PLATE & GASKETREPLACES PUMP FORSIMPLEX UNITS
D
F G E
.13FOOT PAD
S NPTOVERFLOW
R NPTPROCESS RETURN
LIFTING EYES(OPTIONAL)
DRAIN ISOLATION VALVE(OPTIONAL)
4700 "K" SERIES CONDENSATE UNITRECEIVER MATERIAL: CAST IRON
4700SER.K.CDSN.15-24
LH SIDE VIEW
Product Diagrams
2900 South 160th Street, New Berlin, WI 53151 | P: 1.262.641.3808 E: [email protected] W: www.sterlco.com
4700 SERIES
H I
A
3.13
FLOAT SWITCH ORALTERNATOR LOCATION75 GALLON RECEIVERONLY
F G E
D .13FOOT PAD
BACK VIEW
S NPTOVERFLOW
R NPTPROCESS RETURN
DRAIN
LIFTING EYES(OPTIONAL)
C
P
16.00
16.00
THERMOMETER(OPTIONAL)
CONTROL PANEL(OPTIONAL)
CAN BE MOUNTEDREMOTELY
ISOLATION VALVE(OPTIONAL)
FLOAT SWITCH ORALTERNATOR LOCATION
36, 50, AND 120 GALLONRECEIVERS
GAUGE GLASS(OPTIONAL)
GATE VALVE, CHECK VALVE,AND PRESSURE GAUGE
(OPTIONAL)
J
K
B
3.50
L
O N
M
Q NPT VENT
1-1/2" NPTPUMP
DISCHARGE
DUPLEX PUMP
BLANK OFF PLATE & GASKETREPLACES PUMP FORSIMPLEX UNITS
4700 "K" SERIES CONDENSATE UNITRECEIVER MATERIAL: CAST IRON
4700SER.K.CDSN.36-120
Product Diagrams
2900 South 160th Street, New Berlin, WI 53151 | P: 1.262.641.3808 E: [email protected] W: www.sterlco.com
4700 SERIES
G H
M
4.58
C
30.00 2.00 TYP.
LIFTING EYES(OPTIONAL)
CONTROL PANEL(OPTIONAL)
CAN BE MOUNTEDREMOTELY
D F
E O NPTPROCESS RETURN
P NPTOVERFLOW
D B
I A
N NPT VENT
1-1/2" NPT PUMPDISCHARGE
DUPLEX PUMP
L J
16.00
16.00
K
4.00 4.00
DRAIN
GATE VALVE, CHECK VALVE,AND PRESSURE GAUGE
(OPTIONAL)
BACK SIDE VIEW ANDTOP VIEW
SHOWN WITHOUTOPTIONAL CONTROL PANEL
GAUGE GLASS(OPTIONAL)
FLOAT SWITCH ORALTERNATOR
THERMOMETER(OPTIONAL)
ISOLATION VALVE
1/2" DIA. MOUNTINGHOLES (4) PLACES
4700 "K" SERIES ELEVATED CONDENSATE UNITRECEIVER MATERIAL: CAST IRON
4700SER.K.ECDSN.15
Product Diagrams
2900 South 160th Street, New Berlin, WI 53151 | P: 1.262.641.3808 E: [email protected] W: www.sterlco.com
4700 SERIES
C
G H
M
4.58
2.00 TYP.
LIFTING EYES(OPTIONAL)
1/2" DIA. MOUNTINGHOLES (4) PLACES
16.00
16.00
K
30.00
L J
4.00 4.00
CONTROL PANEL(OPTIONAL)
CAN BE MOUNTEDREMOTELY
ISOLATION VALVE
GAUGE GLASS(OPTIONAL)
FLOAT SWITCH ORALTERNATOR
THERMOMETER(OPTIONAL)
I A
D
B
N NPT VENT
1-1/2" NPT PUMPDISCHARGE
DUPLEX PUMP
D F
E O NPTPROCESS RETURN
P NPTOVERFLOW
DRAIN
GATE VALVE, CHECK VALVE,AND PRESSURE GAUGE
(OPTIONAL)
BACK SIDE VIEWSHOWN WITHOUT
OPTIONAL CONTROL PANEL
4700 "K" SERIES ELEVATED CONDENSATE UNITRECEIVER MATERIAL: CAST IRON
4700SER.K.ECDSN.24
Product Diagrams
2900 South 160th Street, New Berlin, WI 53151 | P: 1.262.641.3808 E: [email protected] W: www.sterlco.comRev 10.10.2017
4700 SERIES
C
G H
M
4.58
2.00 TYP.
LIFTING EYES(OPTIONAL)
1/2" DIA. MOUNTINGHOLES (4) PLACES
FLOAT SWITCH ORALTERNATOR LOCATION75 GALLON RECEIVERONLY
J
K
L
30.00
16.00
16.00
4.00 4.00
CONTROL PANEL(OPTIONAL)
CAN BE MOUNTEDREMOTELY
ISOLATION VALVE
GAUGE GLASS(OPTIONAL)
FLOAT SWITCH ORALTERNATOR
THERMOMETER(OPTIONAL)
DRAIN
A
B
D
I N NPT VENT
DUPLEX PUMP
GATE VALVE, CHECK VALVE,AND PRESSURE GAUGE
(OPTIONAL)
1-1/2" NPT PUMPDISCHARGE
D F
E
O NPTPROCESS RETURNP NPTOVERFLOW
4700 "K" SERIES ELEVATED CONDENSATE UNITRECEIVER MATERIAL: CAST IRON
4700SER.K.ECDSN.36-120
R.H SIDE VIEWSHOWN WITHOUT
OPTIONAL CONTROL PANEL