42 Inch Lawn Mower
Transcript of 42 Inch Lawn Mower
S A/k S
Caution:Read and followall Safety Rulesand instructionsBefore OperatingThis Equipment
®
18,0 HP TWUNCYLmNDERELECTRIC START42" MOWER DECK5 SPEED TRANSA×LELAWN TRACTOR
, AssembUyo Operation
Customer Responsibilitieso ServBceand Adjustment, Repair Parts
Sears, Roebuck and Co., Chicago, IL 60684 U.S.A.
SAFETY RULESSafe Operation Practices for Ride-On Mowers
IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OFAM PUTATING HANDS AND FEETAND THROWING OBJECTS,FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH,
GENERAL OPERATION
Road, understand, and follow all instructions in the manualand on the machine before starting.
Only allow respeesible adults, who are familiar with theinstructions, to operate the machine.
Clear the area of eb ects such as rocks, toys, wire, etc,which could be picked up and thrown by the bade.
Be sure the area is etear of other people before mowing Stopmachine if anyone enters the area.
Never carry passengers
Do not mow in reverse unless absolutely necassary_ Alwayslook down and behind before and while backing.
Be aware of the mower discharge direction and do not pointit at anyone. Do not operate the mower without either theentire grass catcher or the guard in place.Slow down before turning
Never leave a running machine unattended. Always turn offblades, set parking brake, stop engine, and remove keysbefore dismounting.Turn off blades when not mowing_
Stop engine before removing grass catcher or uncloggingchute
Mow only in daylight or good artificial light
Do not operate the machine while under the influence ofalcohol or drugs
Watch for traffic when operating near or crossing roadways
Use extra care when loading or unloading the machine intoa trailer or truck
II. SLOPE OPERATION
Slopes are a major factor related to Ioss-of-control and tipoveraccidents, which can result in severe injury or death. Atl slopesrequire extra caution. If you cannot back up the slope or if you feeluneasy ee it, do not mow it.
DO:
Mow up and down slopes, not across_
Remove obstacles such as rocks, tree limbs, etc.
Watch for holes, ruts, or bumps. Uneven terrain couldoverturn the machine Tall grass can hide obstacles.
Use slow speed_ Choose a low gear so that you will not haveto stop or shift white on the slope.Follow the manufacturer's recommendations for wheelweights or counterweights to improve stability.
Use extra care with grass catchers or other attachmentsThese can change the stability of the machine
Keep all movement on the slopes slowand gradual Do notmake sudden changes in speed or direction
Avoid starting or stopping ee a slope. If tires lose traction,disengage the blades arrd proceed slowly straight down theslope
DO NOT:
Do not turn on slopes unless necessary, and then, turn slowlyand gradually downhill, if possib{e_
Do not mow near drop-errs, ditches, or embankments. Themower could suddenly turn over if a wheel is over the edgeof a cliff or ditch, or if an edge caves in_Do not mow on wet grass. Reduced traction could causesliding
Do not tryto stabilize the machine by putting your foot on theground_
Do not use grass catcher on steep slopes
III, CHILDREN
Tragic accidents can occur if the operator is not alert to thepresence of chitdren Children are often attracted to the machineand the mowing activity. Neverassume that children will remainwhere you last saw them
Keep children out of the mowing area and under the watchfulcare of another responsible adult
Be alert and turn machine off if children enter the area
Before and when backing, look behind and down for smallchildren_
Never carry children. They may fall off and be seriouslynjured or nterfere with safe mach ne operation.
Never allow children to operate the machiae_Use extra care when approaching blind corners, shrubs,trees, or other objects that may obscure vision.
IV. SERVICE
Use extra care in handling gasoline and other fuels. They areflammable and vapors are explosive
Use only an approved container
Never remove gas cap or add fuel with the enginerunning Allow engine to cool before refueling. Do notsmokeNever refuel the machine indoors.
Never store the machine or fuel container inside wherethere is an open flame, such as a water heater.
Never run a machine inside a closed area.
Keep nuts and bolts, especially blade attachment bolts, tightand keep equipment in good condition.
Never tamper with safety devices. Check their properoperation regularly.
Keep machine free of grass, leaves, or other debris build-up.Clean oil or fuel spillage. Allow machine to cool beforestoring_
Stop and inspect the equipment if you strike an object.Repair, if necessary, before restarting,Never make adjustments or repairs with the engine running.
Grass catcher components are subject to wear, damage, anddeterioration, which could expcae moving parts or allowobjects to be thrown. Frequently check components andreplace with manufacturer's recommended parts, when nec-essaryMower blades are sharp and can cuL Wrap the blade(s) or'wear gloves, and use extra caution when servicing them.
Check brake operation frequently. Adjust and service asrequired.
Look for this symbol to point out Impor-tant safety precautions. It meansCAUTION!!f BECOME ALERT!!! YOURSAFETY IS INVOLVED.
CAUTION: Always disconnect sparkplug wire and place wire where It cannotcontact spark plug In order to preventaccidental starting when setting up,transporting, adjusting or makingrepairs.
2
CONGRATULATIONS onyour purchase of a Searstractor, It has been designed, engineered and manufac-tured to give you the best possible dependability andperformance,
Should you experience any problem you cannot easilyremedy please contact your nearest Sears ServiceCenter/Department We have competent, we -tra nedtechnicians and the proper tools to service or repair thisunit.
Please read and retain this manual The instructions willenable you to assemble and maintain your unit properly_Always observe the "SAFETY RULES"
MODELNUMBER 917_258492
SERIAL_IUMBER
DATE OF PURCHASE
THE MODEL AND SERIAL NUMBERS WILL BE FOUNDON A PLATE UNDER THE SEAT,
YOU SHOULD RECORD BOTH SERIAL NUMBER ANDDATE OF PURCHASE AND KEEP IN A SAFE PLACEFOR FUTURE REFERENCE
MAINTENANCE AGREEMENT
A Sears maintenance agreement is available on this prod-uct. Contact your nearest Sears store for details.
CUSTOMER RESPONSiBiLiTIES
o Read and observe the safety rule&
o Followa regular schedule in maintaining, caring for andusing your unit.
o Follow the instructions under "Customer Responsibili-ties" and "Storage" sections of this owner's manual,
PRODUCT SPEClFlCATBONSHORSEPOWER: l&0
GASOLINE CAPACITY: &5 GALLONSUNLEADED REGULAR
OIL (3..0PINTS): SAE 30 (above 32° F)SAE 5W-30 (below32° F)
SPARK PLUG (GAP.030 IN.): CHAMPION RJ-19LMSTD361458
VALVE CLEARANCE: INTAKE _004- 006 IN.EXHAUST 007- .009 IN_
GROUND SPEED: FORWARD1st .77 MPH2nd 1.46 MPH3rd &41 MPH4th 4,34 MPH5th 557 MPH
REVERSE: 1.07 MPH
TIRE PRESSURE: FRONT: 14 PSIREAR: 10 PSI
5 AMPS HEADLIGHTCHARGING SYSTEM:
3 AMPS BATTERY
BLADE BOLT TORQUE: 30-35 FT. LBS,
WARNING; This unit is equipped with an internal combus-tion engine and should not be used on or near any unim-proved forest-covered brush-covered or grass-coveredland unless the engineZs exhaust system is equipped witha spark arrester meeting applicable local or state laws (ifany), If a spark arrester Is used it should be maintainea Ineffective work ng order by the operator,
in the state of California the above is required bv law(.Section 4442 of the California Public Resources (_ode),Other states may have similar laws, Federal laws apply onfederal lands,, A spark arrester for the muffler is availablethrough your nearest Sears Authorized Service Center(See REPAIR PARTS section of this manual)
LIMITED TWO YEAR WARRANTY ON ELECTRIC START RiDiNG EQUIPMENTFor two (2) years from the date of purchase, if this riding equipment is maintained, lubricated and tuned up according to theinstructionsin the owner's manual, Sears will repair or replace, free of charge, any parts found to be defective in material orworkmanship.
This Warranty does not cover:
• Expendable items which become worn during normal use, such as blades, spark plugs, air cleaners and belts.• Tire replacement or repair caused by punctures from outsideobjects, such as nails, thorns, stumps, or glass.
Repairs necessary because of operator abuse, negligence, improper storage or accident or the failure to maintain theequipment according to the instructionscontained in the owner's manual.
• Riding equipment used for commercial or rental purposes..
UMiTED 90 DAY WARRANTY ON BATTERYFor 90 days from date of purchase, if any battery included with this riding equipmentproves defective in material or workmanshipand our testing determines the battery will not hold a charge, Sears will replace the battery at no charge.WARRANTY SERVICE IS AVAILABLE BY RETURNING THE RIDING EQUIPMENT TO THE NEAREST SEARS SERVICECENTER/DEPARTMENT IN THE UNITED STATES.
This Warranty gives you specific legal rights, and you may also have other rights which may vary from state to state
SEARS, ROEBUCK AND CO., D/731CR-W,SEARS TOWER, CHICAGO, ILLINOIS 60684
3
TABLE OF CONTENTSSAFETY RULES ............................................................ 2PRODUCT SPECIFICATIONS ....................................... 3CUSTOMER RESPONSIBILITIES ..................... 3, 14-17WARRANTY ................................................................... 3TABLE OF CONTENTS ................................................. 4INDEX ............................................................................. 4TRACTOR ACCESSORIES ........................................... 5ASSEMBLY ................................................................ 7-9
OPERATION ........................................................... 10-13MAINTENANCE SCHEDULE ...................................... 14SERVICE AND ADJUSTMENTS ............................ 18-23STORAGE .................................................................... 24TROUBLESHOOTING ............................................ 25-26REPAIR PARTS - TRACTOR ................................. 28-40REPAIR PARTS - ENGINE ..................................... 41-46PARTS ORDERING/SERVICE ................... BACK PAGE
MNDEXA
Accessories ................................................ 5
Adjustments:Brake ......................................................20Carburetor. ..........................................23
Gauge Wheels ........................................9Mower
Front-To-Back ........................_. 19Side-To-Side ..................................18
Throttle Control Cable .....................22
Air Filter, Engine ..................................... 16Air Screen, Engine .......................................16Assembly ...................................................7-9
B
Battery:Charging ..............................................8Cleaning ........................................ 16installation ................................................9
Levels .............................................8,16Preparation ...........................................8StaRing with Weal( Battery ............21Storage ...................................................24Terminals .........................................16
Bolt:Motion Drive
Remova!/Replacement ........... 20Mower Blade Drive
RemovaVReplacement ................20Blade:
Sharpening ........................................15Replacement ................................... 15
Brake Adjustment ................................. 20C
Carburetor Adjustment ......................... 23Controls, Tractor ......................................10Customer Responsibilities ............. 15-17
Engine:Ail Filter ....................................... 16Air Filter Foam Pre-Cleaner ._..16
Air Screen, Engine .................... 16Battery .......................................... 15Cooling Fins, Engine ............... 17Engine Oil ............................................16Fuel Filter ................................. 17
Spark Plugs ....................................17Tractor:
Blade ....................................... 15Lubrication Chad ........................ 14Maintenance Schedule ..............14
Tire Care ........................... 8,15,21
Cutting Height, Mower ............................11
EElectrical:
Interlocks and Relays .......................22Schematic ..........................................27
Wiring Diagram ................................28Engine:
Air Filter. ...............................................16Air Filter Foam Pre-Cleaner .........16Air Screen .........................................16
Cooling Fins, Engiae ........................17Oil Change .................................... 16Oil Level .................................... 12,16
Oil Type ................................................16Preparation .................................... 12Repair Pads ............................ 41-46Starling ............................................ 13Storage ...............................................24
FFilter:
Air Filter .............................................16Air Filter Foam Pre-Cleaner ........ 16Fuel ...................................................17
Fuel:
Type ...................................................12Storage ........................................... 24
Fuse ......................................................... 22
GGauge Wheel Installation ....................... 9
HHood Removal/installation ................... 22
LLeveling Mower Deck .................... 18-19Lubrication:
Char ............................................ 14
MMaintenance Schedule ......................... 14Mower:
Adjustment, Front-to-Back .............19Adjustment, Side-to-Side .............. 18Adjustment, Gauge Wheel ..............9Blade Sharpening .......................... 15Blade Replacement ..................... 15Cutting Height ...................................11Installation ..................................... 18
Operation ........................................ 12Removal ....................................... 18
Mowing Tips ......................................... 13Muffler ...........................................................17
Spark Arrester .......................... 3,32
4
oOil:
Cold Weather Conditions ....... 12,16Engine ........................................... 16Storage ......................................... 24
Operation ..............; ............................ 10-13Operating Mower ................................ 12Options:
Accessories ................................... 5
Spark Arrester ........................... 3,32P
Parking Brake ................................. 10-11Parts Bag .............................................. 6
Parts, Raplacement/Repair ........... 28-46Product Specifications ............................ 3
R
Repair Parts ......................................28-46S
Safety Rules .............................................2Seat .........................................................8Service and Adjustmerrts..................18-23
Carburetor, ...................................23Fuse .............................................22Hood Removal/Installation .......... 22Motion Drive Belt
RemovaVReplacement ........... 20Mower Blade Drive Belt
RemovaVReplacement ........... 20Mower Adjustment
Front- to-Back ......................... 19Side-to-Side ............................ 18
Mower Removal .......................... 18Tire Care ............................ 8,15,21
Slope Guide Sheet ............................. 47Spark Plugs ........................................ 17Specifications ........................................3Stading the Engine........................ 12-13Steering Wheel ................................ 7,21Stopping the Tractor, .......................... 11Storage ............................................... 24
TThrottle Control Cable
Adjustment .....................................22Tires....................................................8,15,21
Trouble Shooting Chart ..................25-26Transaxle:
Repair Pads........................... 38-39W
Warranty ............................................... 3Wiring Diagram .....................................28Wiring Schematic .................................29
ACCESSORRES ATTACHMENTS
These accessories and attachments were available when the unit was purchased. They are also available at most Sears retail outlets,catalog and service centers. Most Sears stores can order these items for you when you provide the model number of your tractor_
ENGINE
SPARKPLUG MUFFLER AIRFILTER GASCAN ENGINEOIL STABILIZER
MAINTENANCE
BLADES BELTS
PERFORMANCESears offers a wide variety of attachmentsthat fit your vehicle_ Many of these are listed below with brief explanations of how they canhelpyou,.This listwas current atthe time of publication;however, it maychange infutureyears- more attachments maybe added, changesmay be made in these attachments, or some may no longer be available or fit your model. Contact your nearest Sears store for theaccessories and attachments that are available for your unit.
Most of these attachments do not require additional hitches or conversion kits (those that do are indicated) and are designed for easyattaching and detaching
PERMANEX BAGGER lets you collect grass clippings andleaves for a healthier, neater looking lawn. Two Permanexcontainers hold 3B-gallon plastic bags.
LAWN SWEEPERS let you coltect grass clippings and leaves.
LAWN VAOS for powerful collection of heavygrassclippings andleaves. Wand attachment to pick up debris in hard-to-reachplaces.CARTS make hauling easy. Variety of sizes available.ROLLER for smoother lawn surface. 36-inch wide, 18-inchdiameterwater.tight drum holds upto 39Bibs. ofweighL Roundededges prevent harm to tuff. Adjustable scraper automaticallycleans drum.
SPREADER/SEEDERS make seeding, fertilizing, and weedkilling easy. Broadcast spreaders are also useful for granular de-icers and sand.
CORING AERATOR takes small plugs out of soil to allow mois-ture and nutrients to reach grass roots. 36-inch swath. 24hardened steel coring tips. 150 lb. capacity weight tray_
AERATOR promotes deep root growth for a healthy lawn. Ta-pered 2_5-inchsteel spikes mounted on 10_inchdiameter discspuncture holes in soil at close intervalsto let moisture soak inoSteel weight tray for increased penetration,MULCH RAKE/DETHATCHER loosens soil andflips thatch andmatted leavesto lawn surface for easypickup. Twenty spring tineteeth_Usefultopreparebaraareasforseeding Availableforfrontor rear mounting.SPRAYERS use 12-volt DC electric motor that connects to thetractor battery or other 12-volt source. Includes booms forautomatic spraying when pulling, and hand held wand for spotspraying_ Wand has adjustable spray pattern_ For applyingherbicides, insecticides, fungicides, and liquid fertilizers.
SNOW BLADE for snow removal only_ 14-inch high, 42-inchwide blade clears 38-inch path when angled leftor righL Raises,lowers with side lever Adjustable skids; replaceable, reversiblescraper bar. (Usewith tire chains, wheel weights, or reardrawbarweighL)
SNOWTHROWER has 4B-inchswath. Drum-type auger handlespowdery and wetJheavy snow° Mounts easily with simple pinarrangement. Discharge chute adjusts from tractor seat 6-inchdiameter spout discharges snow 10 to 50feel Lift controlled attractor seat. (Use with chains, wheel weights, or rear drawbarweighL)TIRE CHAINS are heavy duty; closely spaced extra-large crosslinks give smooth ride, outstanding traction.WHEEL WEIGHTS for rear wheels provide needed traction forsnow removalor dozing heavy materials. In pairs. (30 Ibs each)TRACTOR CAB has heavy duty vinyl fabric over tubular steelframe, ABS plastic top; clear plastic windshield offers 360 degreevisibility. Hinged metal doors with catch. Keeps operator warmand dry. Remove vinyl and windshields for use as sun protectorin summer. (Catalog only.)
Optional accessories for tractor cab: tinted/tempered solidsafety glass windshield with hand operated wiper; 12-volt ambercaution light for mounting on cab top. (Catalog only.)
TRACTOR COVER protects tractor from weather. Made ofEvolution 3 fabric (water-repellent, extremely breathable, lightweight, soft, non-abrasive, pliable in all temperatures, durable,stain/tear/punctura resistant, will not shrink or stretch.) (Catalogonly.)
TILLER cultivates and prepares soil in one operation Uses PTOfrom tractor; 12 counter-rotating blades. Breaks ground withupper-cutaction, then deflectsand ratills it into a soft, aerated soilChain-drivetransmission_Tills21-inch path, 6-inches deep_(Usechains and wheel weights.)
TILLER has 5hp engineand 36-inch swath to prepare seed beds,cultivate, and compost garden residue. Tiller has its own built-inlift anddepth control systemand does NOT requirea sleeve hitchFits any lawn, yard, or garden tractor. Simply hook up to thetractor drawbar and go!
5
ill
CONTENTS OF HARDWARE PACK
Parts Bag contents shown full size
(1) Shoulder Bolt 5/16-18 (1) Hex Bolt 1/2-13 x t
(1) Lockwasher 1/2
(1) Washer 17/32 x 1-3/16 x 12 Ga.
(2) HexBolts 1/4-20x3/4 (2) HexNuts 1/4-20
(2) Washers 9/32 x 5/8 x 16 Ga,
©(2) Lock washers 1/4
(2) Wing Nuts 1/4 - 20
Parts packed separately in carton
Seat
Steering Wheel
Battery acid
Battery
Parts Bag Owner's Manual
i
Parts bag contents not shown full size
© ©(2) Shoulder (2) Washers (2) Flangelock Nut.,
Bolts 17/32 × 15/16 x 12 Ga, 3/8-16
L_ Steering Wheel
Insert
(2) Battery Carriage Bolts 1/4-20 x 7-1/2
Terminal Guard
(2) Keys
15° Slope Sheet
(2) Gaugewheels
......... J_
Battery Capsand Instructions
6
ASSEMBLYTOOLS REQUURED FOR ASSEMBLY
A socket wrench set will make assembly easier. Standardwrench sizes are listed.
(2) 7/16" wrench
(1) 9/16" wrenches
(1) 1/2" wrench
(1) 3/4" wrench
When right and left hand is mentioned in thismanual, it means when you are in the operating position(seated behind the steenng wheel)
(1) Tire pressure gauge
(1) Screwdriver
(1) Utility knife
TO REMOVE UNUT FROM CARTON
UNPACK CARTON
o Remove all accessible loose parts and parts cartonsfrom carton (See page 6),
• Cut along dotted lines on the carton, fromtopto bottom,all four corners of carton and lay panels flaL
• Check for any additional loose parts or cartons andremove°
BEFORE ROLLING UNUT OFF SKiDATTACH STEERING WHEEL (See Fig. 1)
o Remove hex Iocknut and large flat washer from steer-ing shaft.
° Position front wheels of the tractor so they are pointingstraight forward.
• Position steering wheel so cross bars are horizontal(left to right) and slide onto adapter.
o Assemble large flat washerand 1/2-20 hex Iocknut andtighten securely_
• Snap insert into center of steering wheel.
o Remove protective plastic from tractor hood and grill°IMPORTANT: CHECK FOR AND REMOVE ANYSTAPLES IN SKID THAT MAY PUNCTURE TIRES WHEREUNIT IS TO ROLL OFF SKID.
(See Fig. 6)• Raise attachment lift lever to its highest position.
o Release parking brake by depressing clutch/brakepedal
° Place gearshift lever in "NEUTRAL" position.o Roll unit backwards off skid
o Remove banding holding discharge guard up againsttractor.
INSERT
HEXLOCKNUT
FLATi AS.ER
STEERING
WHEEL
STEERING_/HEEL ADAPTER
+'
¢
/i /
/11
FIG. 1
7
HOW TO SET UP YOUR TRACTOR
PREPARE BATTERY (See Fig. 2)
CAUTION: Wear eye and face shield.
Wash hands or clothing immediately ifaccidentally incontactwith battery acid.
Do not smoke. Fumes from chargedbattery acid are explosive.
Read theinstructionsincluded with thebattery vent caps. Always wear gloves,clothing and goggles to protect yourhands, skin and eyes.
iNSTALL SEAT (See Fig. 3)
Adjust seat before tightening adjustment boll
o Remove cardboard packing on seat pan.
o Place seat on pan and assemble shoulder boll
o Assemble adjustment bolt, lock washer and flat washer_oose_y_Do not tighten.
o Tighten shoulder bolt securely.
• Lower seat into operating position and sit on seat.
o Slideseat untilacomfortablepositionisreachedwhichallows you to press clutch/brake pedal all tire way down(See Fig 6)
° Get off seat without moving its adjusted position.
o Raise seat and tighten adjustment bolt securely..
Your unit has a battery charging system which is sufficientfor normal use. However, periodic charging ofthe batterywith an automotive charger will extend its life
° See instructions packed with vent caps in parts bag
Fill battery with acid_ Fill each cell until it reaches thebottom of the vent wells. Do not overfill.
o Allow battery to stand and settle for at least thirtyminutes After standing, check the level of acid Ifbelow the vent wells, add more acid until the correctlevel is reached_
While battery is standing (after adding acid) and later, whilebattery is being charged, continue with assembly of uniLIMPORTANT: TO MAXIMIZE THE LiFE OF YOURBATTERY,IT IS NECESSARY THAT THE BATTERY BE CHARGED BE-FORE USE° FAILURE TO CHARGE BATTERY CAN RESULTINA SHORTENED BA'Iq'ERY LIFE.
o Charge battery at a rate of 6 amperes for' 1 hour.Observe all safety precautions required for batterycharging.
o Check the acid level after the battery is charged. If theacid has fallen below the correct level, add distilled oriron free water.
° Install the vent caps to coverthe vent wells_ Wash thetop of the battery with water to remove any acid, thenwfpe dry_
o Check battery case for leakage to make sure that nodamage has occurred in handling.
o Dispose of excess battery acid Neutralize acid for'disposal by adding it to four inches of water in a fivegallon plastic container_ Stir' with a wooden or plasticpaddle while adding baking soda until the addition ofmore soda causes no more foaming.
° Follow instructions on how to install battery
CUT AWAY VIEW
I "-F -_VENT CAP
CELL ACID
LEVEL
SEAT
SEAT PAN
SHOULDERBOLT
FLATWASHER
ADJUSTMENT LOCK WASHERBOLT
FIG. 3
CHECK TIRE PRESSURE
The tires on your unit were overinflated at the factory forshipping purposes. Correct tire pressure is important forbest cutting performance_
o Reduce tire pressure to PSI shown in "PRODUCTSPECIFICATIONS" on page 3 of this manual°
CHECK DECK LEVELNESS
For best cuttingresults, mower housingshould be ,properlyleveled_ See TO LEVEL MOWER HOUSING in theService and Adjustments section of this manual.
CHECK FOR PROPER POSITION OF ALLBELTS
See the figures that are shown for replacing motion andmower blade drive belts in the Service and Adjustmentssection of this manual. Verify that the belts are routedcorrectly_
CHECK BRAKE SYSTEM
After you learn how to operate your tractor, check to seethat the brake is properly adjusted. See "TO ADJUSTBRAKE" in the Service and Adjustments section of thismanual.
FIG. 2 8
ASSEMBLY
iNSTALL BATTERY (See Figs. 4 & 5)CAUTION: Do not short battery termi-nals. Before installing battery, remove
metal bracelets, wristwatch bands,rings, etc.
Positive terminal must be connectedfirst to prevent sparking from acciden-tal grounding.
o Make sure draintube isfastened to drain hole in batterytray and battery tray is positioned in hole of batterysupporL
o Place battery in plastic tray, battery terminals to front oftractor.
o First connect RED battery cable to positive (+) batteryterminal with hex bolt, flat washer, lock washer and hexnut as shown Tighten securely
o Connect BLACK grounding cable to negative (-) bat-tery terminal with remaining hex bolt, flat washer, lockwasher and hex nut. Tighten securely.
• Slide the two battery bolts through the terminal guardand start the wing nuts onto the threads
• Position terminal guard over the battery as shown,lower bolts into key holes and slide square shafts ofbolts into slots of key hole&
o Tighten wing nuts by hand making sure battery boltsremain in slots of the key holes in the battery support.
= Be sure terminal access doors are closed.
Use terminal access doors for:
o Inspection for secure connections (to tighten hard-ware).
, Inspection for corrosion.
o Testing battery.
o Jumping (if required).
Periodic charging.
LOCK _::,_.:.::;;..y- .,...... . HEX LOCI{ WASHER"=-_;'-" --' : NUT /
WASHER . ,.., ,., dj_(POSITIVE);"
FLAT(NEGATIVE) '_ WASHER
ASSEMBLE GAUGE WHEELS TO NIOWER
DECK (See Fig. 6)
Assemble gauge wheels with tractor on a flat level surface.
o Lower mower to lowest position with attachment liftlever..
• Adjust mower to desired cutting height with heightadjustment knob ( see "TO ADJUST MOWER CUT-TING HEIGHT in operation section of this manual)
• With mower in desired height of cut position, gaugewheels should be assembled so they are slightly off theground. Install gauge wheel in appropriate hole withhardware shown and tighten securely.
o Repeat for opposite side installing gauge wheel insame adjustment hole.
'GAUGE WHEEL FLAT WASHER
MOUNTING \BRACKET
9
FLANGELOCKNUT
GAUGE WHEEL _/SHOULDER BOLT
FIG. 6
•/ CHECKLISTBEFORE YOU OPERATE AND ENJOY YOUR NEWTRACTOR, WE WISH TO ASSURE THAT YOU RECEIVETHEBESTPERFORMANCEAND SA TISFA CTIONFROMTHIS QUALITY PRODUCT.
Please review the following checldist:
,/ All assembly instructions have been completed.
,/ No remaining loose parts in carton
v" Battery is properly prepared and charged. (Minimum1 hour at 6 amps).
,/ Seat is adjusted comfortably and tightened securely.
,/ All tires are properly inflated. (For shipping purposes,the tires were over-inflated at the factory).
,/ Be sure mower deck is properly leveled side-to-side/front-to-rear for best cutting results (Tires must beproperly inflated for leveling)
,/ Checkmoweranddrivebelts. Besuretheyareroutedproperly around pulleys and inside all belt keepers
,/ Check wiring. See that all connections are still secureand wires are properly clamped
WHILELEARNING HO W TO USE YOUR TRA CTOR, PAYEXTRA ATTENTION TO THE FOLLOWING IMPORTANTITEMS:
,/ Engine oil is at proper level
#" Fuel tank is filled with fresh, clean, regular unleadedgasoline.
,/ Become familiar with all controls - their location andfunction. Operate them before you start the engine
,f Be sure brake system is in safe operating condition.
OPERATIONill .... ii I
KNOW YOUR TRACTOR
READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRAC-TOR
Compare the illustrationswith your tractor to familiarize yourself with the locations of variouscontrols and adjustments_ Savethis manual for future reference
ATTACHMENT CLUTCH LEVER
PLUNGERIGNITION
LIGHT SWITCH SWITCH
THROTTLE CONTROLATTACHMENT'LIFT LEVER
CHOKE
CLUTCH/BRAKE
PEDAL
PARKING
HEIGHT GEARSHIFTADJUSTMENT LEVERKNOB
FIG. 7
Sears tractors conform to the safety standards of the American National Standards Institute,
THROTTLE CONTROL: Used for starting and corrtrollingengine speed.,CHOKE CONTROL: Used for starting a cold engine_
CLUTCH/BRAKE PEDAL: Used for clutching and brakingthe tractor and starting the engine.HEIGHT ADJUSTMENT KNO B: Used to adjust the mowercutting height,
IGNITION SWITCH: Used for starting and stopping theengine.
LIGHT SWITCH: Turns the headlights on and off_
ATrACHMENT CLUTCH LEVER: Used to engage themower blades, or other attachments mounted to yourtractor.
LIFT LEVER PL,UNGER: Used to release attachment liftlever when changing its position,ATTACHMENT LIFT LEVER: Used to raise and lower thenrowerdeck or other attachments mounted to your' tractor.PARKING BRAKE LEVER: Locks ClutcfVBrake Pedal intothe brake position_
GEARSHIFT LEVER: Selects the speed and direction oftractor.
10
OPERATION
The operation of any tractor can result in foreign objects thrown into the eyes, whichcan result in severe eye damage_ Always wear safety glasses or eye shields whileoperating your tractor or performing any adjustments or repairs, We recommend widevision safety mask for over the spectacles or standard safety glasses, available at SearsRetail or Catalog stores_
HOW TO USE YOUR TRACTORTO SET PARKING BRAKE (See Fig. 8)
Depress clutch/brake pedal into full "BRAKE" positionand hold.
Place parking brake lever in "ENGAGED"position andrelease pressurefrom clutch/brake pedal Pedal shouldremain in "BRAKE" positiom Make sure parking brakewill hold vehicle secure.
STOPPING (See Fig. 8)MOWER BLADES -
Move attachment clutch lever to "DISENGAGED" po-sition.
GROUND DRIVE-
Depress clutch/brake pedal into full "BRAKE" positiom
Move gearshift lever to "NEUTRAL" position.ENGINE -
Move throttle control to "SLOW" position,
NOTE: Failure to move throttle control to "SLOW" positionand allowing engine to idle before stopping may causeengine to "backfire".
Turn ignition Key to "OFF" position and remove key.Always remove key when leaving vehicle to preventunauthorized use.
Never use choke to stop engine.
NOTE: Under certain conditions when unit is standing idlewith the engine running, hot engine exhaust gases maycause "browning" of grass, To eliminate this possibility,always stop engine when stopping unit on grass areas.
CAUTION: Always stop unit completely, i
as described above, before leaving theoperator's poeltlon; to empty grasscatcher, etc.
TO USE THROTTLE CONTROL (See Fig. 8)
Always operate engine at full throttle.
Operating engine at less than full throttle reduces thebattery charging rate.
Full throttle offers the best bagging and mower per-formance.
TO MOVE FORWARD AND BACKWARD
(See Fig. 7)
The direction and speed of movement is controlled by thegearshift lever,
Start tractor with clutch/brake pedal depressed andgearshift lever in "NEUTRAL" position.
Move gearshift lever to desired position.
Slowly release clutch/brake pedal to start movement. 1 1
IMPORTANT: BRING TRACTOR TO A COMPLETE STOPBEFORE SHIFTING OR CHANGING GEARS. FAILURETO DO SO WILL SHORTEN THE USEFUL LIFE OF YOURTRANSAXLE,
ATTACHMENTCLUTCH LEVER
THROTTLE "ENGAGED"POSITION
IGNITION KEY
CHOKE
"BRAKE"POSITION
CLUTCH/BRAKEPEDAL"DRIVEPOSITION
GEAR SHIFTLEVER
FIG. 8
TO ADJUST MOWER CUTTING HEIGHT
(See Fig. 9)
The cutting height is controlled by turning the height adjust-ment knob in desired direction.
Turn knob clockwise to raise cutting height
Turn knob counterclockwise to lower cutting height
Thecutting height rangeis approximately 1-1/2to 4" Theheights are measured from the ground to the blade tip withthe engine not running, These heights ere approximateand may vary depending upon soil conditions, height ofgrass and types of grass being mowed.
The average lawn should be cut approximately 2-1/2inches during the cool season and over 3 inches duringhot months_ For healthier and better looking lawns,mow often and after moderate growth,
For best cutting performance, grass over 6 inches inheight should be mowed twice. Make the first cutrelatively high; the second to desired height,
RAISEHEIGHTADJUSTMENTKNOB
)-_, LOWER
FIG, 9
OPERATION
TO OPERATE MOWER (See Fig. 10)
Your unit is equipped with an operator presence sensingswitch Any attempt by the operator to leave the seat withthe engine running and the attachment clutch engaged willshut olf the engine.
o Select desired height of cuL
, Engage mower by slowly moving attachment clutchlever to "ENGAGED' position
• TO STOP MOWER - Move attachment clutch lever to"DISENGAGED" position.
i
!_ CAUTION: DO not operate the mower
without either the entire grass catcher, onmowers so equipped, or the dischargeguard in place.
o If stopping is absolutely necessary push clutch/brakepedal quickly to brake position and engage parkingbrake.
o Move gearshift lever' to 1st gear and be sure you haveallowed room for tractor to roll slightly as you restartmovement.
o To restart movement, slowly release parking brake andclutch/brake pedal
o Make all turns slowly.
TO TRANSPORT
° Raise attachment lift control to highest position.
° When pushing or' towing your unit, be sure gearshiftlever is in "NEUTRAL" position.
° Do not push or tow unit at more than five (5) MPH.
ATTACHMENT CLUTCH LEVERATTACHMENT "ENGAGED" POSITIONCLUTCH LEVER"DISENGAGED" LIFT LEVERPOSITION PLUNGER
LOWESTPOSITION
HEIGHTADJUSTMENTKNOB
LIFT LEVER"HIGHEST"POSITION
FIGo10
TO OPERATE ON HILLS
i,i H, ,,, ,I
I ,#_ CAUTION: Do not drive up or down hillswith slopes greater than 15° and do notdrive across any slope.
H ,,,ll
o Choose theslowest speed before starting upor downhills.
• Avoid stopping or changing speed on hills.
° If slowing is necessary, move throttle control lever toslower position.
BEFORE STARTaNG THE ENGINECHECK ENGINE OIL LEVEL (See Fig. 15)
• The engine in your' unit has been shipped, from thefactory, already filled with summer weight oil.
° Check engine oil with unit on level ground.
o Remove oil fill dipstick and wipe clean, replace andscrew cap tight, wait for a few seconds, remove andread oil level If necessary, add oil until "FULL" markon dipstick is reached. Do not overfill.
o For cold weather operation you should change oil foreasier starting (see "OIL VISCOSITY CHART" in theCustomer Responsibilities section of this manual)..
° To change engine oil, see the Customer Respensibili-ties section in this manual
ADD GASOLINE
° Fill fuel tank_ Use fresh, clean, regular unleadedgasoline_ (Use of leaded gasoline will increase carbonand lead oxide deposits and reduce valve life).
IMPORTANT; WHENOPERATING INTEMPERATURESBELOW 32°F(0°C), USE FRESH, CLEAN WINTER GRADEGASOLINE TO HELP INSURE GOOD COLD WEATHERSTARTING
WARNING: Experience indicates that alcohol blendedfuels (called gasohol or using ethanol or methanol) carlattract moisture which leads to separation and formatton ofacids during storage_ Acidic gas can damage the fuelsystem of an engine while in storage. To avoid engineproblems, the fuel system should be emptied before stor-age of 30 days or longer. Drain the gas tank, start theengine and let it run until the fuel lines and carburetor areempty. Use fresh fuel next season See Storage Instruc-tions for additional inforrnation_ Never use engine orcarburetor cleaner products in the fuel tank or permanentdamage may occur.
.#% CAUT'iON:' Filli0 bottom of gas tank filler-]A A neck. Do not overfill. Wipe off any spilled|
oil or fuel Do not store, spill or use/gasoline near an open flame. |
12
TO START ENGINE (See Fig. 8)
When starting engine for the first time or if engine hasrun out of fuel, it will take extra cranking time to movefuel from the tank to the engine
• Depress the clutch/brake pedal and set the parkingbrake.
o Place gearshift lever in "NEUTRAL" position.
o Move attachment clutch to "DISENGAGED" position,
• Pull choke control out to "CHOKE"position for coldengine start. For warm engine start do not use chokecontrol
° Move throttle control to midway between "FAST" and"SLOW" positions_
per minute. If engine does not start after severalattempts, move throttle control to "FAST" position,wait a few minutes and try again_
o When engine starts, slowly push choke control in.
o Move throttle control to "FAST" position.
o Allow engine to warm up for a few minutes beforeengaging drive or attachment clutch.
NOTE; If at a high altitude (above 3000 feet) or in coldtemperatures (below 32° F), the carburetor fuel mixturemay need to be ad usted for best engine performance.See "TO ADJUST CARBURETOR" in the Service andAdjustments section of this manual.
NiOWgNG TiPS= Tire chains cannot be used when the mower hous_
ing is attached to unit,
o Mower should be properly leveled for best mowin_performance. See TO LEVEL MOWER HOUSINGm the Service and Adjustments section of thismanual.
• The left hand side of mower should be used for trim-ruing.
Drive so that clippings are discharged onto the areathat has been cuL Have the cut area to the right ofthe machine. This will result in a more even distri-bution of clippings and more uniform cutting
When mowing large areas, start by turning to theright so that clippings will discharge away fromshrubs, fences, driveways, etc. After one or tworounds, mow in the opposite direction making lefthand turns until finished(See Fig. 11)_
f
C
FIG, l't
If grass is extremely tall, it should be mowed twiceto reduce load and possible fire hazard from driedclippings° Make first cut relatively high; the secondto the desired heighL
Do not mow grass when it is wet. Wet grass willplug mower and leave undesirable clumps. Allowgrass to dry before mowing_
Always operate engine at full throttle when mowingto assure better mowing performance and properdischarge of material. Regulate ground speed byselecting a low enough speed to give the mowercutting performance as well as the quality of cut de-sired.
When operating attachments, select a ground speedthat will suit the terrain and give best performance ofthe attachment being used,
13
CUSTOM ESPONSNBJLUTHES
sc.,ou,_,v'v'
MAINTENANCEFILL IN DATESAS YOU COMPLETEREGULAR SERVICE
Check Brake Operation _#'
Check Tire Pressure
T Check for Loose Fasteners 6#4
a Sharpen/Replace Mower Blades
_ Lubrication Chad
T Check Battery Level/Recharge
0 Clean Battery and Terminals
R Check Transmission Cooling
Adjust Blade Belt(s) Tension
Adjust Motion Drive Belt(s) Tension
Check Engine Oil Level I_i
Change Engine OII
Clean Air FilterEN Clean Air Screen
G Inspect Muffler/SparkArrester
I Replace Oil Filter (if equipped)
N Clean Engine Cooling FinsReplace Spark Plug
Replace Air Filter Paper Cartridge
Replace Fuel Filter
v'_4
v' v'
e,' e,'
V's, r ,'.,
_1,2,3
V'2
e,,'
v'
I - Change mote oftenwhen operating under a heavy loador In high ambient temperatures2 - Service mole often when operating inditty or dusty conditions
v'
e,"v',
v'3 - Ifequlppedwitholl f_lter,changeollevery50hours4 • ReplacebladesmoreoftenwhenmowingIn sandysoil5 • If equippedwithadjustablesystem
GENERAL RECOMMENDATIONS
The warranty on this vehicle does not cover' items that havebeen subjected to operator abuse or negligence. Toreceive full value from the warranty, operator must main-rain unit as instructed in this manual
Some adjustments will need to be made periodically toproperly maintain your unit.
All adjustments in the Service and Adjustments section ofthis manual should be checked at least once each season.
LUBRICATION CHART
@ "FRONT WHEEL (_)BEARING ZERK _ BEARING ZERK
Once a year you should replace the spark plug, cleanor replace air filter, and check blades and belts for Qwear. A new spark plug and clean air filter assure CLUTCHproper air-fuel mixture and help your engine run better PIVOT(S)andlast longer.
BEFORE EACH USE
Check engine oi! level.
Check brake operation.
Check tire pressure,Check for loose fasteners
(_ SAE 30 OR 10W30 MOTOR OIL APt - SG
(_) GENERAL PURPOSE GREASE
(_ REFER TO CUSTOMER RESPONSIBILITIES "ENGINE" SECTION
IMPORTANT: DO NOT OIL OR GREASE THE PIVOT POINTSWHICH HAVE SPECIAL NYLON BEARINGS VISCOUSLUBRI•CANTS WILL ATTRACT DUST AND DIRT THAT WILL SHORTENTHE LIFE OF THE SELF-LUBRICATING BEARINGS, IF YOUFEEL THEY MUST BE LUBRICATED USE ONLYADRY, POW-
14 DERED GRAPHITE TYPE LUBR CANT SPAR NGLY.
CUSTOMER RESPONSUBILITUESi IMI
TRACTOR TO SHARPEN BLADE (See Fig. 13)
Always observe safety rules when performing any mainte- Care should be taken to keep the blade balanced. Annance, unbalanced blade will cause excessive vibration and even-
tual damage to mower and engine.
BRAKE OPERATION
If unit requires more than six (6) feet stoppingdistance athigh speed in highest gear, then brake mustbe adjusted.(See "TO ADJUST BRAKE in Service and Adjustmentssection of this manual).
TIRES
o Maintainproper air pressure in all tires (See "PROD-UCT SPECIFICATIONS" on page 3 of this manual),
• Keep tires free of gasoline, oil, or insect control chemi-cals which can harm rubber,,
• Avoid stumps, stones, deep ruts, sharp ob ects andother hazards that may cause t re damage
. The blade can be sharpened with a file or on a grindingwheel. Do not attempt to sharpen while on the mower
o To check blade balance you will need a 5/8" diametersteel bolt,pin, or cone balancer, (When using a conebalancer, follow the instructions supplied with the bal-ancer).
o Slide b[ade on to an unthreaded portion of the steel boltor pin parallel with ground. If blade is balanced, itshould remain in a horizontal position. If either end ofthe blade moves downward, sharpen the heavy enduntil the blade is balanced
NOTE: Do not use a nail for balancing blade. The lobes ofthe center hole may appear to be centered, but are not,
BLADE CARE
For best results mower blades must be kept sharp, Theblades can be sharpened with a file or on a grinding wheel.We suggest they be sharpened or replaced after every 25hours of mowing Check blades more often if mowing insandy condition&
o Do not attempt to sharpen blades while they are on themower,
• Replace bent or damaged blades.
BLADE REMOVAL (See Fig. 12)° Raise mower to highest position to allow access to
blades
o Remove hex bolt, lockwasher and flat washer securingblade.
o install new or resharpened blade with trailing edge uptowards deck as shown.
• Reassemble hex bolt, lock washer and flat washer inexact order as shown.
° Tighten bolt securely (30-35 FL Lbs. torque).IMPORTANT: BLADE BOLT IS GRADE 8 HEATTREATED.
FIG. 13
BATTERY (See Fig. 14)Your unit has a battery charging system which is sufficientfor normal use. However, periodic charging of the batterywith an automotive charger will extend it's lifeo
° Acid solution level in each battery cell should be evenwith bottoms ofvent wells. Add only distilledor iron freewater if necessary. Do not overfill.
- Keep battery and terminals clean.• Keep battery bolts tighL
° Keep vent capstight and smallvent holesin caps open,o Rechargeat 6amperesforl hour.
MANDREL
FLATWASHER
LOCK WASHER
BLADE
TRAILING EDGE
HEXBOLT(GRADE8
*A GRADE 8 HEAT TREATED BOLT CAN BE IDENTIFIEDBY SIX LINES ON THE BOLT HEAD.
CUT AWAY VIEW .-VENT CAP
{L----i"_-L__.._j -_/VENT
WELL
I [_ N _ N N }} N N # bBATTERYI _ _ _ [_ riJ _ _] _,,_ CELLACID
VEL
FIG. 14
FIG. 12
15
.1 Ill ,
CUSTOMER RIESPONS BIL TIESTO CLEAN BATTERY AND TERMINALS -
Corrosion and dirt on the battery and terminals can causethe battery to "leak" power,o Remove terminal guard,o Disconnect BLACK battery cable first then RED
battery cable and remove battery from tractor.o Wash battery with solution of four' tablespoons of
baking soda to one gallon of water, Be careful not toget the soda solution into the cells,
o Rinse the battery with plain water and dry.* Cleanterminals and battery cable ends with wire brush
until bright° Coat terminals with grease or petroleum jelly,
o Reinstall battery (See "INSTALL BATTERY" in As-sembly section of this manual)
V-BELTSCheck V-belts for deterioration and wear after 100 hoursand replace if necessary. The belts are not adjustable,Replace belts if they begin to slip from wear
TRANSAXLE COOLING
Keep transaxle free from build-up of dirt and chaff whichcan restrict cooling
ENGINE
LUBRiCATiON
Only use high quality detergent o!1rated with API serviceclassification SG Select the oil s SAE viscosity gradeaccording to your expected operating temperature_
TO CHANGE ENGINE OIL (See Fig. 15)o Be sure vehicle is on level surface
o Oil will drain more freely when warm.o Catch oil in a suitable corrtainer.
o Remove oil flit dipstick. Be careful not to allow dirt toenter the engine when changing oilo
,, Remove drain plug.
• After oil has drained completely, replace oil drain plugand tighten securely
o Refill engine with oil through oil fill dipstick tube. Pour'slowly. Do not overfill For approximate capacity seeProduct Specifications on page 3 of this manual
o Use gauge on oil fill dipstick for checking level Be suredipstick cap is tightened securely for' accurate reading.Keep oil at "FULL" line on dipstick.
PLUG
y AIR SCREEN
FIG. 15
RECOMMENDED SAE VISCOSITY GRADES
oF -20 o 0o 32 ° 60 ° 80° 100°oC -29 ° .18 ° 0o 16° 27 ° 38°
NOTE: Although multi-viscosity oils (5W30, 10W30 etc_)improve starting in cold weather, these multi-viscosityoilswill result in increased oil consumption when used above32°F, Check your engine oil level more frequently to avoidpossible engine damage from running low on oil
Change the oil after the first two hours of operation andevery 25 hours thereafter or at least once a year if thetractor is not used for 25 hours in one year_
Check the crankcase oil level before starting the engineand after' each eight (8) hours of continuous use_ Tightenoil fill cap/dipstick securely each time you check the oillevel,
AiR SCREEN (See Fig. 15)
The engine air screen must be kept free of dirt and chaff toprevent engine damage from overheating. Clean with a wirebrush or compressed airto removed dirt and stubborn driedgum fibers
AiR FILTER FOAM PRE-CLEANER
(See Fig. 16)
Your engine will not run properly and may be damaged byusing a dirty air filteL Clean the foam pre-cleaner elementafter every 25 hours of operation, more often if tractor isused in very dusty, dirty corrditions,• Remove knobs and cover,
,, Remove foam pre-cleaner by sliding it off the papercartridge
NOTE: Do not attempt to clean or oil the paper cartridge,Replace paper cartridge once a year or after every 100hours of operation, more often if used in very dusty, dirtyconditions
° Wash foam pre-cleaner in liquid detergent and water.• Wrap foam pre-cleaner in cloth and squeeze dry.• Lightly coat foam pre-cteaner with clean engine oil.
Squeeze in towel to remove excess oiL Do not saturate.o Install foam pre-cleaner over paper cartridge.o Reassemble cover and secure with knob&
16
CUSTOMER
KNOB
FOAM
OVER
CARTRIDGEPLATE
AIR SCREENCARTRIDGE
FIG. 16
ENGINE COOLING FINS (See Fig. 17)
Remove any dust, dirt or oil from engine cooling fins toprevent engine damage from overheating Air guide coversmust be removed. Remove side panels and hood (See "TOREMOVE HOOD AND GRILL ASSEMBLY" in the Serviceand Adjustments section of this manual).
TOP AIRGUIDE COVER,
ENGINE _.COOLING FINS
AIR GUIDE COVER (BOTH SIDES)\
MUFFLER
FIG. 17
MUFFLER
Inspect and replace corroded muffler and spark arrester (ifequipped) as it could create a fire hazard and/or damage,
SPARK PLUGS
Replace spark plugs at the beginning of each mowingseason or after every 100 hours of use, whichever comesfirst. Spark plugtype and gap setting is shown in "PROD-UCT SPECIFICATIONS" on page 3 of this manual,
IN-LINE FUEL FILTER (See Fig. 18)Fuel filter should be replaced once each season. Iffuel filterbecomes clogged, obstructing fuel flow to carburetor, re-placement is required.
= With engine cool, remove filter and plug fuel linesections_
o Place new fuel filter in position in fuel line_
• Be sure there are no fuel line leaks and clamps areproperly positioned.
o Immediately wipe up any spilled gasoline.
RJEL FILTERCLAMP
CLAMF
FIG. 18
CLEANING• Clean engine, battery, seat, finish, etc+ of all foreign
matter.
o Keep finished surfaces and wheels free of all gasoline,oil, etc.
o Protect painted surfaces with automotive type wax.
We do not recommend using a garden hose to clean yourunit unless the electrical system, muffler, air filter andcarburetor are covered to keep water ouL Water in enginecan result in a shortened engine life
17
SERVmCE ADJUSTMENTSCAUTION: BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS:
o Depress clutch/brake pedal fully and set parking brake.
= Place gearshift lever in "NEUTRAL" position.
° Place attachment clutch in "DISENGAGED" position.° Turn ignition key "OFF" and remove key.o Make sure the blades and all moving parts have completely stopped.
o Disconnect spark plug wire from spark plug and place wire where it cannot come in contact withplug.
TRACTOR
TO REMOVE MOWER (See Fig. 19)Mower will be easier' to remove from the right side of uniL
o Place attachment clutch in "DISENGAGED" position_o Move attachment lift lever forward to lower mower to its
lowest position_
o Roll belt off engine pulley,
= Disconnect clutch rod from clutch lever by removingretainer' spring.
Disconnect suspension arms from rear deck bracketsby removing retainer spring&
° Disconnect front links from deck by removing retainersprings
. Raise lift lever to raise suspension arms. Slide mowerout from under' tractor_
IMPORTANT: IF AN ATTACHMENT OTHER THAN THEMOWER IS TO BE MQUNTED TO THE TRACTOR, BOTHSUSPENSION ARMS MUST BE REMOVED FROMTRACTOR.
TO mNSTALL MOWER (See Fig. 19)o Raise attachment lift lever to its highest position
= Slide mower under tractor with discharge guard to rightside of tractor_
, Lower lift lever to its lowest position.
o Install mower in reverse order' of removal instruction&
NOTE: The mower clutch rod has a trunnion that has been
preset, at the factory, for optimum mower performance. DONOT MOVETHETRUNNION ON THE CLUTCH ROD Iffor
any reason the trunnion has been moved on the clutch rod,it must be reset to correct position (parallel with clutch rod)and measure 10-11/32" (Check dimension on edge of flatwork surface as shown).
Be sure to tighten trunnion nut securely against trunnionafter making any adjustments
TRUNNION
SUSPENSIONARMS
SEENOTEABOVECORRECTTRUNNIONPOSITION
"-- PARALLEL
CLUTCHROD
CLUTCH LEVERRETAINERSPRING
ENGINEPULLEY
RONTUNK
RETAINER
(BOTHSIDES)
RETAINERSPRINGS(BOTH SIDES)
FIG. 19
18
SERVICE AND ADJUSTMENTSTO LEVEL MOWER HOUSING
Adjust the mower while tractor is parked on level ground or,driveway. Make sure tires are properly inflated (SeePRODUCT SPECIFICATIONS on page 3), If tires are
over or under inflated, you will not properly adjust yourmower.SIDE-TO-SIDE ADJUSTMENT (See Figs, 20 and 21).You will need two (2) standard 2 x 4 short pieces of woodto make the following ad ustment. Similar blocks measur-ing 1-1/2 th ck may also be used.
Raise mower with attachment lift control to allow two(2) 1-1/2" thick blocks to be placed under rear edge ofmower directly behind mandrels.
Lower mower deck to its lowest height of cut position(See "TO ADJUST MOWER CUTTING HEIGHT" inOperation section of this manual),
On both sides of tractor, loosen, but do not remove, thefasteners securing the adjustable pivot brackets toframe. Both brackets must be loose enough to movefreely,
Pull down firmly on suspension arm to remove anyslack in pivot bracket and hold while tightening rearfastener first to secure, Tighten remaining fasteners.
Repeat procedure on other side of tractor.Raise mower with attachment lift control and removeblocks from under mower,
PLACE TWO (2) 1-1/2" THICK BLOCKS UNDER REAR EDGE OFDECK (LIse wood 2 x 4's or equivalent)
_%_ I. °°/
MOWER MUST BE IN LOWEST HEIGHT OF CUT POSITION
FIG, 20
ADJUSTABLE PIVOT
BRACKET\ _ FASTENERS
PULL DOWN AND TIGHTEN REAR FASTENER FIRST
FIG. 21
FRONT-TO-BACK ADJUSTMENT (See Figs 22 and 23) -IMPORTANT: DECK MUST BE LEVEL SIDE-TO-SIDE IFTHE FOLLOWING FRONT-TO-BACK ADJUSTMENT ISNECESSARY, BE SUR E TO ADJUST BOTH FRONT LINKSEQUALLY SO MOWER WILL STAY LEVEL SIDE*TO-SIDETo obtain the best cutting results, the mower housingshould be adjusted so that the front is approximately 1/4" to3/4" lower than the rear when the mower is in its highestposition.Check adjustment on right side of tractor, Measure dis-tance "D" directly in front and behind the mandrel at bottomedge of mower housing as shown.
Before making any necessary adjustments, check thatboth front links are equal in length. Both links shouldbe approximately 10-3/8".
If links are not equal in length, ad ust one link to samelength as other link,
To lower front of mower loosen nut "E" on both frontlinks an equal number of turns.When distance "D" is 1/4" to 3/4" lower at front thanrear, tighten nuts "F" against trunnion on both frontlinks.
To raise front of mower, loosen nut"F" from trunnion onboth front links, Tighten nut "E" on both front links anequal number of turns.
When distance "D" is 1/4" to 3/4" lower at front thanrear, tighten nut"F" against trunnion on both front links
Recheck side-to-side adjustment.
MANDREL
FIG, 22
BOTH FRONT LINKS MUST BE EQUAL IN LENGTH
NUT =F"'__ NUT "E"
FRONT LINKS TRUNNION
FIG. 2319
SERVICE ADJUSTMENTS
WITHPARKINGBRAKE"ENGAGED"TO REPLACE MOWER BLADE DRIVE BELT(See Fig. 24)The mower blade drive belt may be replaced withouttools_ Park the tractor on level surface Engage parkingbrake For assistance, there is a belt installation guidedecal on the mower housing.BELT REMOVAL -o Place attachment clutch in "DISENGAGED" position.
o Move attachment lift lever forward to lower mower toits lowest position
o Roll belt off engine pulley_
* Work belt off both mandrel pulleys and idler pulleys,
o Pull belt away from moweLBELT INSTALLATION -
Install new belt in reverse order of removal
° Make sure belt is in all pulley grooves and inside allbelt guides,
MANDREL IDLERPULLEY PULLEYS
ENGINE PULLEY
MANDRELPULLEY
FIG. 24
TO ADJUST BRAKE (See Fig. 25)Your unit is equipped with an adjustable brake systemwhich is mounted on the right side of the transaxle
If unit requires more than six (6) feet stopping distance athigh speed in trighest gear, then brake must be adjusted
., Depress clutch/brake pedat and engage parking brake_
o Measure distance between brake operating arm andnut "A" on brake rod
° If distance is other than 1_1/2', disengage parkingbrake, loosen jam nut and turn nut "A" until distancebecomes 1-1/2'L Retighten jam nut against nut "A"
o Engage parking brake and recheck distance.
= Road test unit for proper stopping distance as statedabove_ Read ust if necessary. If stopping distance isstill greater than six (6) feet n highest gear, furthermaintenance is necessary. Contact your nearest au-thorized service center.
NUT"A"
\
JAM NUT
OPERATINGARM
FIG. 25
TO REPLACE MOTION DRIVE BELT (SeeFig. 26)Park the tractor on level area. Engage parldng brake.For assistance, there is a belt installation guide decal onbottom side of left footrest.o Remove mower (See "TO REMOVE MOWER" in this
section of this manual)o Remove belt from stationary idler and clutching idler.o Remove belt from engine pulley.o Roll belt over top of transaxle pulley.o Install new belt by reversing above procedure,IMPORTANT: REPLACE ONLY WITH BELT LISTEDIN THIS MANUAL
PULLEY
FRAME
CLUTCHIN(
STATIONARYIDLER ENGINE
PULLEY
FIG. 26
20
SERVICE AND ADJUSTMENTSTO ADJUST STEERING WHEEL AUGNMENT
If steering wheel crossbars are not horizontal (left to right)when wheels arepositioned straight forward, removesteering wheel and reassemble per instructions in theAssembly section of this manual
FRONT WHEEL TOE-IN/CAMBERThe front wheel toeqn and camber are not adjustable onyour unit If damage has occurred to affect the front wheeltoe-in or camber, contact your nearest Sears ServiceCenter,
TO REMOVE WHEEL FOR(See Fig. 27)o
u
o
o
REPAIRS
Block up axle securely.
Remove axle cover, retaining ring and washers to allowwheel removal (rear wheel contains a square key - Donot lose).
Repair tire and reassemble
On rear wheels only: align grooves in rear wheel huband axle. Insert square key
Replace washers and snap retaining ring securely inaxle groove.
Replace axle cover.
WASHERS
RETAININGRING
AXLE COVERI
(REAR WHEEL ONLY)
FIG, 27
TO START ENGRNE WiTH A WEAK BAT-TERY (See Figs. 28 & 29)
I& CAUTION: Lead-acid batteries gener-
ate explosive gases. Keepsparks,flameand smoking materials away from bat-teries. Always wear eye protectionwhen around batteries.
If your battery is too weak to start the engine, it should berecharge& If "jumper cables" are used for emergencystarling, follow this procedure:IMPORTANT: YOUR UNIT IS EQUIPPED WITH A 12VOLT NEGATIVE GROUNDED SYSTEM. THE OTHERVEHICLE MUST ALSO BE A 12 VOLT NEGATIVEGROUNDED SYSTEM. DO NOT USE YOUR TRACTORBATTERY TO START OTHER VEHICLES.
TO ATTACH ,JUMPER CABLES -o Connect each end of the RED cable to the POSITIVE
(+) terminal of each battery, taking care not to shortagainst chassis
o Connect one end of the BLACK cable to the NEGA-TIVE (-) terminal of fully charged battery
o Connect the other end of the BLACK cable to a panelbolt on the left side of the chassis, away from fuel tankand battery
To remove cables, reverse order -o BLACK cable first from left side of chassis and fully
charged battery_o RED cable last from both batteries.
"POSITIVE.... NEGATIVE"(+) (°)
FIG. 28
PANELBOLT
FIG. 29
21
TO REPLACE FUSE
Replace with 30 amp automotive-type plug-in fuse. Thefuse holder is located in the engine compartment, directlyin front of the dash
TO REPLACE HEADLIGHT BULBo Raise hood.
o Pull bulb holder out of the hole in the backside of thegrill
o Replace bulb in holder and push bulb holder securelyback into the hole in the backside of the grill
= Close hood_
ENGINETO ADJUST THROTTLE CONTROL CABLE
(See Fig. 32)The throttle control has been preset at the factory andadjustment should not be necessary. Check adjustment asdescribed below before loosening cable. If adjustment isnecessary, proceed as follows:
• With engine not running, movethrottle controllever to"FAST" position_
o Check that swivel is against side of quarter circle. If itis not, loosen cable clamp screw arrd pull cable backuntil swivel is against quarter circle Tighten cableclamp screw secur'ely_
INTERLOCKS AND RELAYS
Loose or'damaged wiring may cause your' tractor to runpoorly, stop running or prevent it from starting.
o Check wiring. See electrical wiring diagram in RepairParts section of this manual
TO REMOVE HOOD AND GRILL ASSEMBLY
(See Figs. 30 and 31)o Raise hood.
o Unsnap headlight wire connector.
= Unscrew one screw at rear of each side panel.
° Pivot hood and side panels forward and lift off tractor.
• To reinstall, reverse procedure_
TO ADJUST CHOKE CONTROL (See Fig. 33)The choke control has been preset at the factory andadjustment should not be necessary. Check adjustment asdescribed below before loosening cable.. If adjustment isnecessary, proceed as follows:
• With engine not running, move,choke control (locatedon dash panel) to full 'CHOKE position.
o Remove air cleaner cover, filter and spitback plate toexpose carburetor choke (see "AIR FILTER" in theCustomer' Responsibilities section of this manual).
o Choke should be c{osed_ If it is not, loosen casingclamp screw and move choke cable until choke iscompletely closed. Tighten casing clamp screw se-cureJy.
o Reassemble air cleaner
SCREW_
FIG. 30
WIRECONNECTION
CLAMP
QUARTER
SWIVEL
FIG. 32
CHOKECLOSI
CASINGCLAMPSCREW _'_
CHOKELEVER
FIG. 31
22
FIG. 33
SERVICE ADJUSTMENTSTO ADJUST CARBURETOR(See Fig. 34 & 35)The carburetor has been preset at the factory and adjust-ment shouldnot benecessary, However minoradjustmentmay be required to compensate for differences in fuel,temperature, altitude or load If the carburetor does needadjustment, proceed as follows:
In general turning the mixture screw in (clockwise) de-creases the supply offuel to the engine giving a leaner fuel/air mixture, Turning the mixture screw out (counterclock-wise) increases the supply of fuel to the engine giving aricher fuel/air mixtureIMPORTANT: DAMAGE TO THE NEEDLES AND THESEATS IN CARBURETOR MAY RESULT IF SCREW ISTURNED IN TOO TIGHT
PRELIMINARY SETTING• Be sure you have a clean air filter, and the throttle
control cable and choke are adjusted properly (seeabove).
° With engine off turn idle mixture screw in (clockwise)closing it finger tight and then turn out (counterclock-wise) 1-1/4 to 1-1/2 turns.
FINAL SETTING -
o Start engine and allow to warm forfive minutes. Makefinal ad ustments with engine running and shift! motioncontro ever in "NEUTRAL" position_
- With throttle control lever in "SLOW" position, holdthrottle lever against idle speed screw and adjust idlespeed screw to obtain 1200 to 1400 RPM
= While still holding throttle lever against idle speedscrew, turn idle mixture screw in (clockwise) untilengine begins to die and then turn out (counterclock-wise) until engine runs rough Turn screw to a pointmidway between those two positions,
• Continueto holdthrottle leveragainst idle speed screwand adjust idle speed screw to obtain 900 to 1200 RPM.Release throttle lever_
ACCELERATION TEST -
• Move throttle control lever from "SLOW" to "FAST"position. If engine hesitates or dies. turn idle mixturescrew out (counterclockwise) 1/8 turn. Repeat testand continue to adjust, if necessary, until engine accel-erates smoothly_
High speed stop isfactory adjusted, Do not adjust- damagemay resulL
IMPORTANT: NEVER TAMPER WITH THE ENGINEGOVERNOR, WHICH IS FACTORY SET FOR PROPERENGINE SPEED. OVERSPEEDING THE ENGINE ABOVETHE FACTORY HIGH SPEED SETTING CAN BEDANGEROUS. IF YOU THINK THE ENGINE-GOVERNEDHIGH SPEED NEEDS ADJUSTING, CONTACT YOURNEAREST AUTHORIZED SERVICE CENTER, WHICH HASPROPER EQUIPMENT AND EXPERIENCE TO MAKE ANYNECESSARY ADJUSTMENTS.
IDLESPEEDSCREW
MIXTURESCREW
THROTTLELEVER
FIG. 34
THROTTLe= \ IDLEMIXTURELEVER SCREW
FIG. 35
23
STORAGE
ENGINEImmediately prepare your tractor' for storage at the end ofthe season or if the unit will not be used for 30 days or more.
CAUTION: Never store the tractor withgasoline in the tank inside a buildingwhere fumes may reach an open flameor spark. Allow the engine to coolbefore storing in any enclosure.
TRACTORRemove mower from tractor' for winter storage Whenmower' is to be stored for a period of time, clean it thor-oughly, remove all dirt, grease, leaves, etc. Store in aclean, dry area.
o Cleanentiretractor(See"CLEANING"intheCustomerResponsibilities section of this manual).
Inspect and replace belts, if necessary (See belt re-placement instructions in the Service and Ad ustmentssect on of th s manua ).
o Lubricate as shown in the Customer Responsibilitiessection of this manual.
° Be sure that all nuts, bolts and screws are securelyfastened. Inspect movingpartsfordamage, breakageand wear Replace if necessary
Touch up all rusted or chipped paint surfaces; sandlightly before painting.
BA'N'ERY
o Fully charge the battery for storage
o After a period of time in storage, battery may requirerecharging
• To help prevent corrosion and power' leakage duringlong periods of storage, battery cables should bedisconnected and battery cleaned thoroughly (see"TOCLEAN BATTERY AND TERMINALS in the Cus-tomer Responsibilities section of this manual).
o After cleaning, leave cables disconnected and placecables where they cannot come in contact with batteryterminals.
° Be sure battery drain tube is securely attached
FUEL SYSTEMIMPORTANT: IT IS IMPORTANT TO PREVENT GUMDEPOSITS FROM FORMING IN ESSENTIAL FUELSYSTEM PARTS SUCH AS CARBURETOR, FUEL FILTER,FUEL HOSE, OR TANK DURING STORAGE, ALSO,EXPERIENCE INDICATES THAT ALCOHOL BLENDEDFUELS (CALLED GASOHOL OR USING ETHANOL ORMETHANOL) CAN ATTRACT MOISTURE WHICH LEADSTO SEPARATION AND FORMATION OF ACIDS DURINGSTORAGE. ACIDIC GAS CAN DAMAGE THE FUELSYSTEM OF AN ENGINE WHILE IN STORAGE.
o Drain the fuel tank.
o Start the engine and let it run until the fuel lines andcarburetor' are empty.
o Never use engine or carburetor cleaner products in thefuel tank or permanent damage may occur.
o Use fresh fuel next season.
NOTE: Fuel stabilizer is an acceptable alternative inminimizing the formation of fuel gum deposits during stor-age. Add stabilizer to gasoline in fuel tank or storagecontainer'. Always follow the mix ratio found on stabilizercontainer. Run engine at least 10 minutes after' addingstabilizer to allow the stabilizer to reach the carburetor. Donot drain the gas tan k and carburetor if using fuel stabilizer.
ENGINE OIL
Drain oil (with engine warm) and replace with clean engineoil. (See "ENGINE" in the Customer Responsibilitiessection of this manual),.
CYLINDERS
• Remove sparkplug(s).
o Pour one ounce of oil through spark plug hole(s) intocylinder(s).
o Turn ignition keyto"START"position forafewsecondsto distribute oil
o Replace with new spark plug(s).
OTHERo Do not store gasoline from one season to another.
o Replace your gasoline can if your can starts to rust.Rust and/or dirt in your gasoline will cause problems.
o If possible, store your unit indoors and cover it to giveprotection from dust and dirt_
o Cover your unit with a suitable protective cover thatdoes not retain moisture_ Do not use plastic. Plasticcannot breathe which allows condensation to form andwill cause your unit to rust
IMPORTANT: NEVER COVER TRACTOR WHILE ENGINEAND EXHAUST AREAS ARE STILL WARM_
24
TF OUBLESHOOTmNG POHNTS
CAUSE CORRECTIONPROBLEM
Wtll not start
Hard to start
Engine will not turn over
Engine clicks but will notstart
Loss of power
Excessive vibration
1 Out of fuel2 Enginenot"CHOKED"propedy_3 Engine flooded4, Bad spark plug,5. Dirty air filter6. Dirty fuel filter,7 Water In fuel
8 Loose or damaged wiring,9 Carburetor out of adjustment
10 Engine valves out of adjustment
l r Dirty air filter,2. Bad spark plug3 Weak or dead batter,/,4 Dirty fuel filter,5 Stale or dirty fuel6, Loose or damaged wiring7, Carburetor out of adjustment8 Engine valves out of adjustment
1, Clutch/brake pedal not depressed2, Attachment clutch Is engaged3. Weak or dead battery4_ Blown fuse.5, Corroded battery terminals6 Loose or damaged widng7- Faulty Ignition switch8 Faulty sotenotd or starter9 Faulty operator presence switch(es)
1_ Weak or dead battery2, Corroded battery terminals3. Loose or damaged wiring4 Faulty solenoid or starter
1, Cutting too much grass/too fast2, Throttle In "CHOKE" position.3_ Bultd.up of grass, leaves end trash under mower4_ Dirty air filter5_ Low el! level/dirty oll6 Faulty spark plug7_ Dldy fuel filter8 Staleor dirty fue!9, Water In fuel
10, Sparkplug wire loose11. Dldy engine air screen/fins12, Dldy/clogged muffler_13 Loose or damaged wiring14 Carburetor out of adjustment15 Engine valves out of adjustment,
1 Worn. bent or loose blade2 Sent blade mandrel3 Loose/damaged pert(s)
1 FII! fuel tank2 See "TO START ENGINE" In Operation section3 Wait several minutes before attempting to start
4 Replace spark plug5. Clean/replace air filter6 Replace fuel filter,7 Drain fuel tank and carburetor, refill tank with fresh
gasoline and replace fuel filter8, Check all wiring.9 Contact Sears Service Center/Department
10_ Contact Sears Service Center/Department,
1 Clean/replace air filter2 Replace spark ptug3, Recharge or replace battery4 Replace fuet filter5, Drain fuel tank and refill with fresh gasoline6 Check nil wiring7 Contact Sears Service Center/Department8 Contact Sears Service Center/Department
1, Depress clutch/brake pedal2, Disengage attachment clutch3, Recharge or replace battery4 Replace fuse,5 Clean battery terminals6 Check atl wiring7 Check/replace Ignition switch8 Check/replace solenoid or starter9 Contact Sears Service Center/Department
1, Recharge or replace battery2 Clean battery terminals3 Check all wiring4 Check/replace solenoid or starter
1 Set In"Htgher Cut" position/reduce speed2. Adjust throttle control3, Clean underside of mower housing4 Clean/replace air filter5, Check oitlevel/change oit6 Clean and regap or change spark plug7, Replace fuel filter8 Drain fuel tank and refill with fresh gasoline9 Drain fuel tank and carburetor, refill tank with fresh
gasoline and replace fuel filter10 Connect and tighten spark plug wire11. Clean engine air screen/fins12 Clean/replace muffler13 Check all wiring14 Contact Sears Service Center/Department15 Contact Sears Service Center/Department,
f Replace blade, Tighten blade bolt2 Replace blade mandrel3 Tighten loose part(s) Replace damaged parts
25
TF OUBLESHOOTJNG POINTSPROBLEM CAUSE CORRECTION
Engine continues to runwhen operator leaves seatwith attachment clutchengaged
Poorcut-uneven
Mower blades wlll notrotate
Poor grass discharge
Headlight(s) not working(If so equipped)
Battery will not charge
Engine "backfires"when turning engine"OFF"
1 Faulty operator-safety presence control system
1. Worn, bent or loose blade2 Mower deck not level3. Buildup of grass, leaves, and trash under mower4 Bent blade mandrel5 Clogged mower deck vent holes from buildup of
grass, leaves, and trash around mandrels
1 Obstruction in clutch mechanism
2 Worn/damaged mower drive belt3. Fro:_en tdler pulley.4. Frozen blade mandrel
1 Engtne speed tee slow2 Travel speed too fast3 Wet grass4. Mower deck not level
5 Low/uneventIrealr pressure6. Worn, bent or loose blade7 Buildup of grass, leaves and trash under mower8 Mower drive belt worn,
9 Blades Improperly Installed10 Improper bladesusedt I Clogged mower deck vent holes from bulIdup of
grass, leaves, and trash around mandrels
1 Switch Is "OFF"2 Bulb(s) burned cut3 Faulty light switch4 Loose or damaged wiring5 Blown fuse
1 Bad battery cell(s).2 Poor cable connections3. Faulty regulator (If so equlpped)4. Faulty aftemator
1_ Engine throttle control not set at "SLOW"position for 30 seconds before stopping engine
1 Check wiring, switches and connections. If notcorrected, contact Sears Service Center/Department
1 Replace blade Tighten blade bolt2 Level mower deck.
3 Clean underside of mower housing4 Replace blade mandrel5 Clean around mandrels to open vent holes
1 Remove obstruction
2 Replace mower ddve belt3 Replace idler pulley4 Replace blade mandrel
Place throttle control tn "FAST" position2 Shlftto slower speed.3 Allow grass to dry before mowtng4 Level mower deck
5 Check tires for proper air pressure.6 Replace/sharpen blade Tighten blade bolt7 Clean underside of mower housing.8 Replace mower drive belt,9 Reinstall blades sharp edge down_
10 Replace with blades listed In this manual11 Clean around mandrels to open vent holes,
1 Turn switch "ON"
2 Replace bulb(s)3 Check/replace light switch4 Check wtring and connections5 Replace fuse
1_ Replace battery2 Check/clean all connections3 Replace regulator4 Replace alternator,
1 Move throttle control to "SLOW" position and allowto Idle for 30 seconds before stopping engine
26
18 HP 42" TRACTOR = = MODEL NUMBER 917.258492SCHEMATIC
BATTERY
E,
SLACK
-7
f I
I
FUSE30 AMP. _ i IWHITE I i I
_ ..... J
TILLER OLENOID__ ATTACHMENT
CONNECTOR/ WHITE
IGNITION SWITCH
t ...... i 1
w.,TE w.,TEI I II I I
I _j I t II t I
(PEDAL UP)
I ATPMENTCLUTCHaLACK J (CLUTCHOFF)
BLACK
BLACK
IGNITION SWITCH
POSITION CIRCUIT
OFF M + G
ON B +LSTART B + S
NON-REMOVABLECONNECTIONS
REMOVABLECONNECTIONS
R_D_ )STARTER
I-- I
I I
t
SEATSWITCH
(NOT OCCUPIED)
(_ IGNITIONUNITSPARK _--_ )
PLUGS @------4 )
BED (_ 13 AMPREGULATOR YELLOW
12VOLTS AC (MIN)@3600 RPM
4)
5AMPS ALTERNATOR@ 11 VOLTS AO @ 3600 RPM
t- I
I...... IHEADUGHT I IH AD
SWITG'H- L--(d _ LIGHTS(OFF) _-J
WIRING INSULATED CLIPS
NOTE: IF WIRING INSULATEDCLIPS WERE REMOVED FORSERVICING OF UNIT, THEYSHOULD BE REPLACED TOPROPERLY SECURE YOURWIRING
NOTE
YOUR TRACTOR IS EQUIPPED WITHA SPECIAL ALTERNATOR SYSTEM.THE LIGHTS ARE NOT CONNECTEDTO THE BATTERY, BUT HAVE THEIROWN ELECTRICAL SOURCEBECAUSE OF THIS, THE BRIGHTNESSOF THE LIGHTS WILL CHANGE WITHENGINE SPEED. AT IDLE THE LIGHTSWILL DIM. AS THE ENGINE ISSPEEDED UP, THE LIGHTS WILLBECOME THEIR BRIGHTEST.
27
REPAnR PARTS18 HP 42" TRACTOR = - MODEL NUMBER 917.258492
ELECTRICAL
2O
31
3
A B C D E F G
_10 39 39 23 51
<:_12 _40 _34 _52813 @s3
41 _46
\
\J I
, 48_.I
I
L ...... I\
28
38
II
II
+
36 +J
I
I
I
t
6
. 4
\
]
//
//
//
/
28
REPAURPARTS18 HP 42" TRACTOR - - MODEL NUMBER 917.258492
ELECTRICAL
KEY PART KEY PARTNO. NO. DESCRIPTION NO. NO. DESCRIPTION
12345
6789
1012131415'1617181920212223242526
109310X127441X4152J4406R109553X
124211X1107'12X109081X100904007335040011050400735104001315631332534799J4206J4207J123620X121537X121305X104445X17021008108824X7476041219091016
Key, Molded 27 !0040400Harness, Light Socket 28 73220400Light Bulb 29 123198XSwitch, Ignition 30 11050600Switch, Interlock, Attachment 31 102476XClutch 32 72240460Nut, Ignition 33 74641008Switch, Light 34 73951000Solenoid 36 102501XWasher, Lock 1/4 37 2751RNut, Hex, Jam 1/4-20 38 235RWasher, Lock, External Tooth '1/4 39 74780408Nut, Keps 1/4-20 40 73680400Cover, Terminal 41 10054'1KHarness, Ignition 42 109596XCable, Battery 43 4171RCable, Battery 44 121264XCable, Ground 46 7603,, ICover, Key Switch 47 7192JBattery (Includes Electrolyte) 46 108236XSwitch, Seat 49 17021008Switch, Interlock, Clutch 50 110923XScrew, Hex, Tapping #10-24 x 1/2 51 74760616Fuse 52 19131312Bott, Hex 1/4-20 x 3/4 53 73680600Washer 9/32 x 5/8 x 16 Gauge
Washer, Lock 1/4Nut, Hex 1/4-20Nut, Wing 1/4-20Washer, Lock External Tooth 3/4Guard, TerminalBolt, Carriage 1/4-20 x 7-1/2Screw, Slotted Pan Head #10-32Nut, Keps #10-32Wire LoopClip, Fue/LineClip, InsulatedBolt, Hex 1/4-20 x 1/2Nut, Crownlock 1/4-20TubeClamp, HoseClip, InsulatedCaps, BatteryTray, BatteryCable, TieBracket, SwitchScrew, Hex, Tapping #10-24 x 1/2Bracket, Mower ClutchBolt, Hex 3/8-16x 1Washer 13/16 x 13/32 x 12 GaugeNut, Crownlock 3/8-'16
NOTE: All component dimensions given in U.& inches1 inch = 2&4 mm
29
REPAIR PARTS18 HP 42" TRACTOR - - MODEL NUMBER 917.258492
CHASSIS AND ENCLOSURES
1
90
o?
97
51
//
ij 109
43
6768
lol 76
j112
61
42
1 115 J
A B
_6_7
C D E F
84 7 5 108
_88 ®2o___389
G H J K L N P Q R S T U
30
REPABRPARTS18 HP 42" TRACTOR =- MODEL NUMBER 917.258492
CHASSIS AND ENCLOSURES
KEY PART KEY PARTNO. NO. DESCRIPTION NO. NO. DESCRIPTION
1 127437 Seat 67 106004X2 74760612 Bolt, Hex, Fin. 3/8m16x 3/4 68 1322573 126656X Bracket, Pivot, Seat 69 127018X4 105529X Bolt, Shoulder 5/16-18 70 108512X5 74780814 Bolt, Hex 1/2-13 x 7/8 7'1 108513X6 73510500 Nut, Keps 5/16-18 74 721106087 73680600 Nut ,Crownlock 3/8-16 76 110350X4178 12'1642X417 Fender 77 110506009 106090X Hinge, Hood LH 81 174906'16
10 105953X Air Duct11 17490612 Screw, Hex Washer Head, Thd, 84 17490608
Roll. 3/8-16 x 3/412 19131312 Washer 13/32x 13/16x 12 Gauge 88 1004080013 STD523707 Bolt, Hex 3/8q6x3/4 89 1917191214 106091X Hinge, Hood RH 90 13'145119 124181X Spring, Compresion 91 121251X20 19131614 Washer 13/32x 1 x 14 Gauge 92 121246X21 105509X Bracket, Fender 93 t21249X23 127334X Tank, Fuel 94 7205041124 123549X Cap, Fuel 95 12t250X25 123487X Clamp, Hose 96 121248X26 5277J Fuel Line 97 123976X28 135034 Assembly, Chassis 98 120579X29 130805 Drawbar 99 5320R30 124118X Panel, Dash, LH 101 123650X31 121794X Cover, Access 102 105838X32 133748 Panel, Dash, RH 103 105839X33 105525X Bracket, Support, Dash 104 13374735 105465X417 Footrest, LH 105 106909X36 105464X417 Footrest, RH 106 106910X37 72'110606 Bolt, Carriage 3/8-16x3/4 107 108402X42 135029 Guard, Muffler 108 1749061243 110436X Grommet, Split 109 105511X48 109015X Bracket, Pivot, LH 110 105466X49 109016X Bracket, Pivot, RH 111 106082X50 106013X417 Hood 112 3645J51 2751R Clip, Fuel 113 8710J54 108067X Pal Nut 114 13477455 105528X Grill 115 13477558 19131616 Washer 13/32x 1 x 16 Gauge 116 7214060661 108403X417 Panel, Side, RH 117 109227X62 108410X417 Panel, Side, LH66 106003X Lens, RH
Lens, LHBezel, HeadlightBolt, ShoulderBracket, Pivot, RHBracket, Pivot, LHBolt, Carriage 3/8-16 x 1Assembly, Strap, GrillWasher, Lock, External Tooth 3/8Screw, Hex Washer Head, Thd.Roll 3/8q6 x 1Screw, Hex Washer Head, Thd,Roll. 3/8-16 x 1/2Washer, Lock 1/2Washer 17/32 x 1-3/16 x 12 GaugePan, SeatStrip, FoamBracket, Switch MountSpacer, SplitBolt, Carriage 1/4-20 x '1-'1/4Spring, CompressionBushing, SnapNut, Flange, Large, HexPal NutClip, InsulatedStud, 1/4 TurnRetainer, 1/4 TurnReceptical, 1/4 TurnShield, HeatScrew,Washer Speclal
U-ClipScrew, Thd. Roll. 3/8-16 x 3/4Strap Assembly, FenderPad, FootrestPad, SpacerBushingStem, Fuel TankBracket, Pivot, LHBracket, Pivot, RHBolt, Carriage 3/8-16 x 3/4Pad, Spacer
NOTE: All component dimensions given in U.S. inches1 inch = 25.4 mm
31
REPAIR PARTS18 HP 42" TRACTOR - - MODEL NUMBER 917.258492
DRIVE
7
fJ
3940
53
6058
7O
38
9"9
I -OPTIONAL i
EQUIPMENT.SPARK
ARRESTERKIT
25
6271
83
87 64 593_
8O
• 83
6
A B
_90 _ 24
(_27 _27
28
C D E F G H J
@28 @1o3_103
32
K M N
107 _ 10128
REPAIR PARTS18 HP 42" TRACTOR - - MODEL NUMBER 917.258492
DRIVE
KEY PART KEY PARTNO. NO. DESCRIPTION NO. NO. DESCRIPTION
1 123667X Pulley, Transaxle 57 760204122 12000028 Ring, Retainer 58 1332613 73800600 Locknut, Hex, with Washer Insert 59 130804
3/8-16 60 124236X4 136193 Transaxle, Dana, 5 Speed, 61 106888X
Model Number 4360-42 62 191313185 126470X Clip, Insulated 63 121746X6 13200300 Elbow, STD 90 °, 3/8-18 64 733506007 13280336 Nipple, Pipe 67 1277838 132415 Engine, Briggs & Stratton, 18 HP, 68 123789X
Model #422707, Type #1516-01 69 123205X9 108373X Muffler 70 74760624
10 100229L Tube Assembly, Exhaust 71 110812X11 74780412 Bolt, Hex 1/4-20 x 3/4 72 1200003912 10040400 Washer, Lock 1/4 73 105709X13 8545J Gasket 74 105710X14 2228M Key, Woodruff #9 76 13275515 129921 Keeper, Belt, Engine 77 1772041016 104757X Cap, Axle17 131006 V-Belt, Drive 78 5919218 2751R Clip 79 6513919 I06933X Knob 80 124632X20 131679 Rod, Shifter 81 106106X36121 105701X Washer, Shaft Plate 82 109502X22 19151216 Washer 15/32 x 3/4 x16 Gauge 83 121749X23 76020416 Pin, Cotter 1/8 x 1 84 1200000124 17490612 Screw, Hex Washer Head, Thd., 86 123583X
Roll. 3/8-16 x 3/4 87 12729025 134683 Keeper, Belt, Engine 88 1749062426 74760612 Bolt, Hex 3/8-16x3/427 19131312 Washer 13/32 x13/16 x12 Gauge 89 1749051228 73880600 Nut, Crewniock 3/8-1629 8883R Cover, Pedal 90 7476061630 122424X Shaft, Foot Pedal 91 105706X31 1572H Pin, Roll 3/16x 1 92 7104041232 19211616 Washer 21/32x 1 x 16 Gauge 94 13080233 120183X Bearing, Nylon 97 7152J37 136715 Keeper, Chassis, Center Span Belt 98 110422X38 109070X Keeper, Be_t 99 13292239 4470J Spacer 100 7351060040 123674X Idler, Flat 101 1105060042 134825 Pulley, Engine 102 7476054443 10040700 Washer, Lock 7/16 103 7368050044 71170764 Bolt, Hex 7/16-20x4 104 7476051245 127289 Keeper, Belt, LH 106 - - -49 19091210 Washer 9/32 x 3/4 x10 Gauge53 74760644 Bolt, Hex 3/8-16 x 2-3/4 107 1913201254 121520X Strap, Torque55 130807 Bracket, Transaxle
Pin, Cotter 1/8 x 3/4Rod, Parking BrakeRod, BrakeCapSpring, Brake RedWasher 13/32 x 13/16 x 16 GaugeWasher 25/32 x 1-5/8 x 16 GaugeNut, Hex, Jam 3/8-16Pulley, IdlerArm, IdlerRetainer, BeltBolt, Hex 3/8-16 x 1-1/2Washer, HardenedRing, KlipSpring, Return, ClutchLink, ClutchControl, ThrottleScrew, Hex Head, Thread Cutting1/4-20 x 5/8Cap, ValveStem, ValveTire, RearRimSpacer, SplitWasher 25/32 x 1-!/4 x 16 GaugeE-RingKey, Square 25x 1845/1865Keeper, Belt, RHBolt, Hex Washer Head, Thd, Roll3/8-16 x 1-1/2Screw, Hex Washer Head, Thd.,Roll, 5/16-18 x 3/4Bolt, Hex 3/8-16 x 1BearingBolt, Hex 1/4-28 x 3/4Bracket, Saddle ShiftTube (Optional, Service Item Only)Spring, Return, BrakeKit, Spark ArresterNut, Keps 3/8-16Washer, Lock, External Tooth 3/8Bolt, Hex, Fin. 5/16-16 UNC x 2.3/4Nut, Crownlock 5/16-18Bolt, Hex Head 5/16-16 x 3/4Plug, Oil Drain(Order from Engine Manufacturer)Washer 13/32 x 1-1/4 x 12 Gauge
NOTE; All component dimensions given in U S inches1 inch = 25,4 mm
33
REPAIR PARTS18 HP 42" TRACTOR - - MODEL NUMBER 917.258492
STEERING ASSEMBLY
20 22
27
10
9
\
\\
16
M
85
42
57
45 54
\
53
51
46
40.56
66 64
12 72
5267 68
69
34
REPAURPARTS18 HP 42" TRACTOR .. = MODEL NUMBER 917.258492
STEERING ASSEMBLY
KEY PART KEY PARTNO. NO. DESCRIPTION NO. NO. DESCRIPTION
1 104757X2 1337423 739408004 100712K5 1337416 100711L7 1060'15X8 120028X9 129621X01 t
'10 109816X11 t7490608
12 121749X13 12875516 124036X19 12750120 120000292I 6266H22 124034X24 105518X25 74180512
26 7368050027 13t005X01028 7368060029 7476O53230 121236X31 '12823132 7476061233 5707934 124035X35 126684X36 13277937 17490612
38 '11050600
39 7211060840 13145042 7401105645 110438X46 736O1000
Cap, Axle 48Insert, Steering Wheel 49Nut, Top-Lock 1/2-20 UNF 50Washer 51Steering Wheel 52Adapter, Steering Wheel 53Sleeve, Steering 54Dash 55Plate, Dash 56Nyliner, Snap-In 57Screw, Hex Washer Head, Thd., 58Roll.. 3/8-16 x 1/2 59Washer 25/32 x 1-I/4 x 16 Gauge 61Shaft, Steering 62Bracket, Steering 64Shaft, Pitman 65Ring, Klip 66Bearing, Thrust 67Gear, Sector 68Dash, Lower 69Screw, Crown Truss Head 725/16-18 x 3/4Nut, Crownlock 5/16-18 73Saddle 74Nut, Crownlock 5/1648 75Bolt, Hex 5/16-t 8 x 2 77Spacer 78Plate, Battery Support 79Bolt, Hex 3/8-16 x 3/4 80Washer 83Support, Shaft 84Washer 5/8 x 1/4 x 16 Gauge 85Control, Choke 86Screw, Hex Washer Head, Thd. 87Rol!., 3/8-16 x 3/4Washer, Lock, Internal / External 88Tooth 3/8 89Bolt, Carriage 3/8-16 x t Grade 5 90Axle, Front 91Bolt, Hex 5/8-11 x 3-1/2 92Spacer, Bearing, Front Axle 95Locknut, Hex, with Washer Insert5/8-16 UNC
135227135228121748X13046519131416760204123366R13046810040600736106001554J174310082751R732206005919265139278H9040H106732X361106222X59904
7211O622121235X191314167418O412t90912167351O4O0192720165320Rt20754X121232X1004040071070410
132624106933X110924X131671106451X131291
Spindle, LHSpindle, RH 'Washer 25/32 x 1-5/8 x 16 GaugeRod, TieWasher 13/32 x 7/8 x 16 GaugePin, Cotter 1/8 x 3/4BearingLink, DragWasher, Lock 3/8Nut, Hex 3/8-24Bushing, SteeringScrew, Hex #10_16 x 1/2Clip, Fuel LineNut, Hex 3/8-16Cap, ValveStem, ValveFitting, GreaseBearingRimTire, FrontTube, Tire, Front(Optional, Service Item Only)Bolt, Carriage 3/8-16 x 2-3/4SpacerWasher 13/32 x 7/8 x 16 GaugeScrew, Pan Head I/4-20 x 3/4Washer 13/32 x 3/4 x 16 GaugeNut, Keps 1/4-20 UNCWasher 27/32 x 1-1/4 x 16 GaugeClip, InsulatedBushingCap, SpindleWasher, Lock 1/4Screw, Hex Socket Head1/4-20 x 5/8Pin, AxleKnobLever, Mower ClutchBracket, PivotBolt, ShoulderLink, Clutch
NOTE: All component dimensions given in U...£oinchest inch = 2&4 mm
35
REPAIR PARTS18 HP 42" TRACTOR - - MODEL NUMBER 917.258492
42" MOWER DECK
67 7O
52
45
42
43
6O
91
9089
8088
21 19 92
8281
80
77
21
96
4
13
93
14
18
16
15
12
36
REPAUR PARYS18 HP 42" TRACTOR - - MODEL NUMBER 917.258492
42" MOWER DECK
KEY PART KEY PARTNO. NO. DESCRIPTION NO. NO. DESCRIPTION
1 1309702 1309693 110485X4 1287745 133172
6 1298957 1278438 1299629 10030600
10 85085711 12896112 13096813 13149114 13126715 110452X16 123713X17 1911101618 105304X19 7351050020 7214050621 4939M22 12721823 7335080024 13017125 7380080026 13538827 13556328 13083329 13461933 13384434 7815835 12996336 12986137 7305090038 72110614
39 13394340 13149441 122052X42 1913161243 13350244 13350345 7368060046 7211061847 13383548 13134049 13394050 6918051 105529X52 13184553 13394454 13133555 133551
Mower Deck Assembly, 42" 56 76020312V-Belt, 42" Mower 57 133504Bail Bearing, Mandrel 58 134236Housing, Mandrel, Vented 59 134666Shaft Assembly, Mandrel, Vented 60 73350600(Includes Key Number 6) 61 133205Ball Bearing, #6204Blade, High Lift, 42 Mower 62 4497HWasher, Hardened 63 17720410Washer, Lock, Heavy HelicalSpring 3/8 64 127498Bolt 3/8-24 x 1-1/4 Grade 8 65 133435Stripper, Mower, Vented 66 127847Shield, Deflector 67 128903Rod, Hinge 68 12000029Bracket, Deflector 69 121748XNut, Push 70 127845Spring, Torsion, Deflector 72 127846Washer 11/32 x 5/8 x 16 Gauge 73 128759Cap, Sleeve 74 12000022Nut,Kaps 5/16_18 75 19292016Bolt, Carriage 5/16-18x3/4 76 131925Retainer, Spring 77 121002XLink, Front 78 74780624Nut, Hex, Jam 1/2-13 UNC 79 121006XTrunnion 80 2876HLocknut, with Washer Insert 1/2-13 81 122364XLink, Lift, RH 82 122365XPin, Roll 83 125631XArm, Suspension, Rear 84 110810XLink, Lift, LH 85 19151216Arm, Idler 86 12000037Bolt 5/16-18x1-1/4T/T 87 110807XWasher, Spacer 88 19131016Pulley, Mandrel 89 76020308Nut, Top-Lock 9/16 90 110729XBolt, Carriage 91 100734K3/8-16 UNC x 1_3/4 Grade 5Washer, Hardened 92 134753Pulley, Idler, Flat 93 132262Spacer, Retainer 94 132263Washer 13/32x 1 x 12 Gauge 95 72110504Spacer, Idler Arm, Upper 96 74760512Stiffener, Idler Arm, Upper 97 73680500Nut, Crownlock 3/8-16 UNC 98 134249Bolt, Carriage 3/8-16 x 2-1/4 99 105455XFastener, Christmas Tree 100 19171512Bolt, Shoulder #10-24 Grade 5 102 73800600Roller Assembly, Cam Follower - - 130794Locknut #10-24 UNCBolt, Shoulder 5/16_18 UNC - - 136322Arm Assembly, Brake PadWasher, HardenedSpring, ExtensionRod, Pivot, with Nibs
Pin, Cotter 3/32 x 3/4Rod, Clutch, Secondary, with NibsGuard, Mandrel, LHRod, Clutch, Primary, with NibsNut, Hex, Jam 3/8-16 UNCTrunnion, Adjustment3/8-16 UNC x 1.30Spring, RetainerScrew, Hex, Thread Cuttting1/4-20 x 5/8BushingSpring, Extension, ReturnArm, Clutch, SecondaryBolt, Shoulder 3/8-16 UNC 1.44Ring, KlipWasher 25/32 x 1-5/8 x 16 GaugeKeeper, SpringArm, Clutch, PrimarySpring, Clutch, MowerE-Ring #5166-87Washer 29/32 x 1-1/4 x 16 GaugeShaft Assembly, LiftLever Assembly, LiftBolt, Hex, Fin. 3/8-16 UNCx 1-1/2Rod Assembly, LeverSpring 2-1/8Plunger, Lift LeverButton, Plunger, RedGrip, Handle, FlutedTrunnion, Depth StopWasher 15/32 x 3/4 x 16 GaugeRing, Klip #T5304-37Nut, SpecialWasher 13/32 x 5/8 x !6 GaugePin, Cotter 3/32 x 1/2Rod, Lift AdjustmentKnob, Infinite Height Adjustment,Black 3/8-16 UNCStiffener, Deflector BracketBracket, Gauge Wheel, RHBracket, Gauge Wheel, LHBolt, Carriage 5/16-18 x 1/2Bolt, Hex 5/16-18 x 3/4Nut, Crownlock 5/16-1 UNCBolt, ShoulderWheel, Gauge, BlackWasher 17/32 x 15/16 x 12 GaugeNut, Nylock 3/8-16 UNCMandrel Assembly (Includes KeyNumbers 3-6, 8-10, 35 and 37)Mower Deck, 42"(Does Not Include Gauge Wheelsand Brackets, or Lift System)
NOTE: All component dimensions given in U_S. inches1 inch = 25.4 mm
37
REPAIR PARTS18 HP 42" TRACTOR - - MODEL NUMBER 917.258492
DANA TRANSAXLE - - MODEL NUMBER 4360-42
2021
25
54 44
5556
57
59
1247
49
50
8
62
66
59
6465
6869 _771
6O
52
38
REPAIR PARTS18 HP 42" TRACTOR - - MODEL NUMBER 917o258492
DANA TRANSAXLE - - MODEL NUMBER 4360-42
KEY PART KEY PARTNO. NO. DESCRIPTION NO. NO. DESCRIPTION
1 124643X2 2274J
3 1344004 105904X5 105905X6 1347887 '1343998 120951X9 134791
10 2267J11 13479312 124641X13 120415X14 225_J15 106846X16 106095X17 105909X18 105910X19 105911X20 108976X21 1O5913)(22 12046823 2242J24 124638X25 2244J26 105916X27 120470X28 110070X29 108977X30 124644X31 108980X32 120406X33 13479634 13479735 105925X36 2232J37 108978X38 110079X
39 124639X40 120472X41 105928X
Housing, Upper 42 106605XScrew, Tapping, Large 43 1343941/4-20 x .734 44 120473XBail, Detent 45 106596XSpring, DetentScrew, Set 46 105933XKit, Shifter Assembly 47 106589XBoot, Shifter 48 120408XPuck, Friction 49 105937XScrew, Tapping, w/Sealer 50 105936XRing, Retaining 51 2226J
* Assembly, Kit, Shim, .625 Shaft 52 134401Gear, Spur, 20 Teeth 53 2264JWasher, Plain .632 x 138 x .046 54 120474XKey, Woodruff, #9 55 120409XAssembly, Kit, Input Shaft 56 105941XPinion, Bevel, 14 Teeth 57 110071XRing, Retaining 58 120952XChain, 24 Pitches 59 106592XBearing, Flange 60 120475XGear, Spur, 14 Teeth 61 134798Collar, Clutch 62 120961XKey, Clutch 63 7294JKey, Woodruff, #3 64 108989XShaft, Intermediate 65 120953XKey, Woodruff, #61 66 120954XRing, Retaining 67 134799Sprocket, 18 Teeth 68 108992XSpacer 69 108996XGear, Spur, 37 Teeth 70 120956XGear, Spur, 30 Teeth 71 738'10500Gear, Spur, 25 Teeth 72 120416XGear, Spur, 22 TeethGear, Spur, 19 TeethSpacer 1.133 x 1.50 x 375Washer, Plain .640 x 1.37 x .061Washer, Plain °632 x 1_00x ,026Spacer .630 x 1.00 x .169Assembly, Gear, Combination,12 Teeth and 35 TeethShaft, IdlerSpacer .633 x .87 x .755Sprocket, 9 Teeth
Gear, Bevel, 42 Teeth* Assembly, Kit, Shim, .750 Shaft
Shaft, DriveScrew, Tapping, Large5/16-18 x 1A4Gear, Spur, 12 TeethGear, Spur, 25 TeethGear, Spur, 28 TeethGear, Spur, 31 TeethSpacer .781 x 1.00 x .375Washer, Plain .632 x 1.00 x .060Washer, NeopreneWasher, Plain .758 x 1o25 x 031Axle, Left HandGear, Miter, 15 TeethRing, RetainingGear, Spur, 32 TeethShaft, CrossGear, Miter, 15 TeethAxle, Right HandHousing, LowerPuck, FrictionDisc, BrakeSpacerJaw, BrakePin, DowelScrew, Tapping 5/16-18 x 2.25Lever, ActuatingWasher, Plain 321 x 1.00 x .055Bracket, Anti-RotationLocknut 5/16-24Grease
* Use in various combinations to maintain properclearances.
** OrderKey Number 15.
*** Lubricate with Aerospace Lubricant Inc,PC-80 or equ vaent.
NOTE: All component dimensions given in U,S. inches1 inch = 25,4 mm
39
REPAIR PARTS18 HP 42" TRACTOR - - MODEL NUMBER 917.258492
DECALS
6
22 3 1111 15 20 5 5 2 21
417
8
12
23
13
1014
9 19
KEY PART KEY PARTNO. NO. DESCRIPTION NO. NO. DESCRIPTION
1 1361282 1306003 1305994 105568X5 126312X6 105801X7 1331108 1337969 4900J
10 109199X11 13313912 136832
Decal EngineDecal Hood, Stripe, LHDecal Hood, Stripe, RHDecal Grill, StripeDecal Hood, HPDecal FenderDecal U_S.A,Decal CautionDecal Clutch/BrakeDecal V-Belt DriveDecal ChassisDecal Mower Drive Belt
13 121343X14 3713J15 13226916 108456X17 105806X18 12826019 13317920 106814X21 106813X22 133644
23 135919-- 135509
Decal, DangerDecal, Rotating BladesDecal, Steering WheelDecal, Operating InstructionsDecal, Logo, GrillDecal, Model, GrillDecal, QC SystemDecal, Stripe, Side Panel, RHDecal, Stripe, Side Panel, LHDecal, Maintenance, SearsDomesticDecal, Battery Cable, 30 Amp, Min,Manual, Owner's
4O
REPAIR PARTS"i8 NP 42" TRACTOR - - MODEL NUMBER 917.258492
BRIGGS & STRATTON ENGINE - - MODEL NUMBER 422707, TYPE NUMBER 1516-01
61S(_,
_A_5
616 _0
_230
219&
* REQUIRES SPECIAL TOOLS TO INSTALL.SEE REPABR INSTRUCTION mANUAL°
41
REPABR PARTS18 HP 42" TRACTOR - ° MODEL NUMBER 917.258492
BRIGGS & STRA3-rON ENGINE - - MODEL NUMBER 422707, TYPE NUMBER 1516-01
434
_119
235
42
REPASR PARTS18 HP 42" TRACTOR - - MODEL NUMBER 917.258492
BRIGGS & STRA'I-FON ENGINE - - MODEL NUMBER 422707, TYPE NUMBER 1516-01
332
@75
,,,,,
78
i
474
%482
_Z)307 J
1S
43
REPAIR PARTS18 HP 42" TRACTOR - - MODEL NUMBER 917.258492
BRIGGS & STRATrON ENGINE - - MODEL NUMBER 422707, TYPE NUMBER 1516-01
1003
Reference Number
ManufacturerBdggs& HousfngStmtton Lenetf1
!2V 3-5/8"*IncludesBrush,Set
309 310 311 544 801Motor and Thru Bolt Brash Altnaturo Drive End Ca
Ddv® Am_'v. Assembly Assembly i Asssmblv Asssmbly
394808 94003 395539 390837 394860
802 _EndCapAss'y. HousingCommutator Assembly
39'ss37' _93s2s
i
Reference Number 510Starter Starter Drive
Motor Mfr. GroupB & S or United Tech.
12V 490421
513 783 876 896,i H i
Clutch Gear Pinion Rol!
Assembly Sprlnq Kit Pin
398003 280104 490467 94288 (Copper)
44
REPAnR PARTS18 HP 42" TRACTOR - = MODEL NUMBER 917.258492
BRIGGS & STRATTON ENGINE - - MODEL NUMBER 422707, TYPE NUMBER 1516-01
KEY PART KEY PARTNO. NO. DESCRIPTION NO. NO. DESCRIPTION
1 4945332 3992653 391086
5-1 4934575-2 4934587-1 2718677-2 2718688-1 3933708-2 222892
9 2780310 9438211 28022512 271142
271188271189
13 9456515 91084
15A 94497'16 394028
9419618 49330420 29167521 39919522 90887
23 491180
24 22269825 394955
394956394957394958
26 394959394960394961394962
27 26092428 299691
39128629 394306
397158
31 22086332 9290933 39041934 26152835 6590636 2682840 2215964'1 29226042 93630
45 261368
Cylinder Assembly 46 212337Bearing, Cylinder 50 213290Seal, Oil 51 271412Head, Cylinder #1 51A 280319Head, Cylinder #2 52 270884Gasket, Cylinder Head #1 53 93970Gasket, Cylinder Head #2Breather Assembly #1 54 93208Cover, Breather Cylinder #2 75 222511(Used only on Key Number 572 Air 78 94326Baffle with Holes for Mounting) 81 223016
* Gasket, Valve Cover 90 491429Screw, SeresTube, Breather 91 491541
*Gasket, Crankcase Cover 1/64" 93 231209* Gasket, Crankcase Cover ,,005" 94 491538*Gasket, Crankcase Cover .009" 95 93499
Screw, Cylinder HeadPlug, Oil Drain 96 221939Plug, Pipe 97 392672Crankshaft 98 91920Key, Timing Gear Retaining Device 99 26157Base Assembly, Crankcase 102 271607Seal, Oil 103 298514Seal Assembly, Cylinder Plug 104 230896Screw, Seres, Crankcase Cover 105 394683Mounting (Uses#92268 Lock 107 491543Washer) 108 223534Flywheel and Ring Gear Assembly, 109 392673Magneto 116 280474Key, Flywheel 117 231338Piston Assembly, Standard 119 94152Piston Assembly .010" Oversize 120 92290Piston Assembly .020" Oversize 121 491539Piston Assembly .030"Oversize 127 223472Ring Set, Piston, Standard 161 398826Ring Set, Piston .010" Oversize 165 94289RingSet, Piston .020"Oversize 187 299146Ring Set, Piston _030" Oversize 188 93535Lock, Piston Pin 201 262683Pin Assembly, Piston, Standard 202 262684Pin Assembly, Piston .005" Over 203 280997Rod Assembly, Connecting 203A 490207Connecting Rod, 205 93971.020" Undersize Crankpin Bore 206 94298Washer 207 262337Screw, Connecting Rod 209 262352Valve, Exhaust 209A 261563Valve, IntakeSpring, Intake ValveSpring, Exhaust ValveRetainer, Intake ValveRotocoil, Exhaust ValveRetainer, Exhaust ValveRotocoil (2)Tappet, Valve
Gear, CamManifold Assembly, Intake
*** Gasket, Carburetor & Intake ElbowSpacer, Carburetor
* Gasket, Intake Manifold MountingScrew, Hex Head (Carburetor toManifold)Screw, Sems, Intake Manifold MtgWasher, SpringScrew, SeresLock, Muffler ScrewCarburetor Assembly (RemoteChoke)Body Assembly, Upper CarburetorBushing, Throttle Shaft
** Valve Assembly, Carburetor IdleScrew, Sems, Throttle and ChokeValve MountingValve, ThrottleShaft and Lever, ThrottleScrew, Machine, Fillister HeadSpring, Throttle Adjustment
** Gasket, Carburetor BodyFloat, Carburetor
** Pin, Float Hinge** Valve, Fuei Inlet
Body, Lower CarburetorValve, ChokeShaft and Lever, ChokeO-RingJet, Needle Valve, FixedScrew, Seres, Hex HeadWasher, LockCarburetor Overhaul KitPlug, WelchBody, Air CleanerNut, Wing .Line, Fuel, 28 (Cut to Suit)Screw, SeresLink, GovernorLink, ThrottleCrank, BellCrank, BellScrew, Hex HeadNut, SquareSpring, CompressionSpring, GovernorSpring, Governor Idle
* Includedin Gasket Set (491856)** Included in Carburetor Overhau/Kit (491539)
*** Included in both Gasket Set (491856) andCarburetor Overhaul Kit (491539)
NOTE: All component dimensions given in U.S, inches1 inch = 25.4 mm
45
REPAURPARTS18 HP 42" TRACTOR =- MODEL NUMBER 917.258492
BRNGGS & STRATrON ENGINE - - MODEL NUMBER 422707, TYPE NUMBER 1516-01
KEY PART KEY PARTNO. NO. DESCRIPTION NO. NO. DESCRIPTION
216 262375 Link 520 93722219 393415 Oil Slinger' Assembly 523 394020219A 394348 Gear', Governor 524 271157220 222773 Washer, Thrust 524A 271485222 491282 Bracket, Speed Control 525 280224224 94297 Screw, Pan Head 528 393815227 491297 Lever Assembly, Governor 535 271271229 62199 Washer' 537 271411230 223882 Washer, Governor' Crank (Inside) 552 262332232 262539 Spring, Backlash 552A 262331235 224039 Shield, Spitback 556 93585240 394358 Filter, Fuel (In Fuel Line to Tank) 562 93853244 230318 Connector;lmpulsePump 567 93777257 93897 Screw, Sems258 93949 Screw, Sems 569 270981259 223890 Bracket, Cable 572 224580265 221535 Clamp, Casing 573 491304267 93496 Screw, Hex Head 592 92278284 94264 Screw, Hex Head 601 93053284A 93469 Screw, Hex Head 615 94296304 491247 Housing, Blower 616 491530305 94608 Screw, Sems 1/2" 634 271013
93415 Screw, Seres 3/4" 634A 491287306-1 222846 Shield, Cylinder 635 66538306-2 222847 Shield, Cylinder 642 223579307 94386 Screw, Sems 643 223714308-1 222848 Cover, Air Guide 726 391362308-2 222849 Cover, Air Guide309 - - - Motor, Starting (See Chart for' 741 262694
Starting Motor Replacement Parts) 819 93686319 394988 Armature Assembly 842 271170332 230674 Nut, Hex 847 394394333 394891 Armature Group 851 221798
(MAGNETRON TM Ignition) 858 270989334 93381 Screw, Seres, Armature Mounting 859 271025337 802592 Plug, Spark, Resistor' 860 261358353 92791 Washer, Lock, Shakeproof 861 393397354 90576 Nut, Hex 868 393606356 398808 Wire, Ground 869 261463358 491856 Gasket Set 870 213316363 19203 Puller, Flywheel 871 261961
(Optionat Accessory) 231218383 89838 Wrench, Spark Plug387 280197 Body, Pump 877 393456392 261395 ***Spring, Pump 881 212455394 270988 ***Diaphragm 955 397882414 223882 Washer 1005 280815422 222875 Clamp, Oil Filler 1006 223726432 221377 ***Cap, Spring 1019 491262434 223688 Cover, Diaphragm435 93829 Screw, Diaphragm Cover445 394019 Cartridge, Air' Cleaner467 493903 Knob, Air Cleaner468 222673 Screen, Flush Rotating474 393474 Stator, Alternator, Dual Circuit482 93621 Screw, Seres506 231174 Terminal507 280180 Grommet, Insulator
Terminal, SpadeCap and Dipstick, Oil FillerSeal, Filler TubeSeal, TubeTube, Oil FillerImpulse Line and Clamp AssemblyElement, Air Cleaner'
*** Gasket, Air CleanerLower Bushing, GovernorUpper' Bustling, GovernorScrew, Seres, Hex HeadBolt, Governor Lever'Screw, Hex Head(Back Plate to Cylinder)
* Gasket, CrankcaseBaffle, Air, Cylinder #2Back Plate AssemblyNut, HexClamp, Fuel LineRetainer, E-RingCrank, Governor
** Washer', Throttle ShaftSeal, Governor ShaftElbow, Spark PlugCover, Air CleanerCartridge Plate, Air CleanerGear', Flywheel Ring(Includes Mounting Parts)Gear, TimingScrew, Hex HeadSeal, Oil Filler CapDipstick and Tube AssemblyTerminal, Ignition Cable
*** Diaphragm, Damping*** Gasket, Carburetor Pump*** Spring (2)
Repair Kit, PumpSeal and Retainer AssemblySeat, Intake Valve, StandardSeat, Exhaust Valve, StandardGuide, Exhaust Valve (Only)Guide, Intake, Brass(See Repair' Manual)Connector Assembly, Dual CircuitCover Plate, CrankcasePlug and Seal, SolenoidFan, FlywheelRetainer, FanLabel Kit
* Included in Gasket Set (491856)** Included in Carburetor Overhaul Kit (491539)
*** Included in both Gasket Set (491856) andCarburetor Overhaul Kit (491539)
NOTE: All component dimensions given in US. inches1 inch = 25_4 rnm
46
Z0b=
W
0WLk
0LLU_
0.Jg_
gO
0LL
_Pr_W
U_
...s"1"z i t
I
I
i-
I
I
oLO
, !ii!
2 .-_ R_!_
_ _ ..: I_
_ ._ _:_C: ,_, 0 _- I_:_
o _ .__ _) II_::_
_=_ I_
47
S_ A/k SOWNER'SMANUAL
HOW TO ORDERREPAIR PARTS
®
18=0 P TWHNCYLINDERELECTRHC START42" OWER DECK5 SPEED TRANS_LELAWN TRACTOR
Each tractor has its own model number. Each engine has its own modelnumber=
The model number for your tractor will be found on the model platelocated under the seat.
The model number for your engine will be found on the blower housing,
All parts listed herein may be ordered from any Sears, Roebuck and Co,Service Centers and most Retail Stores,
WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THE FOLLOW-ING INFORMATION:
• PRODUCT- LAWN TRACTOR
• MODEL NUMBER - 917,258492
• ENGINE MODEL NUMBER - 422707, TYPE NUMBER 1516-01
• PART NUMBER
• PART DESCRIPTION
Your Sears merchandise has added value when you consider Sears hasservice units nationwide staffed with Sears trained technicians., profes-sional technicians specifically trained to insure that we meet our pledge
to you, we service what we sell
Sears, Roebuck and Co., Chicago, IL 60684 U.S.A.
PRINTED IN US,A,135509 Rew 2 06,10.92