412.09 Technical and WAG 3 STAGING, STORAGE, … · Temporary units Tanks or containers in...
Transcript of 412.09 Technical and WAG 3 STAGING, STORAGE, … · Temporary units Tanks or containers in...
Table 3.1.4-l SSSTF REGULATORY REFERENCES r SSSTF/ICDF Complex
Functional Block Flow Diagram Block Number ARAR General’
Description Applicable Unit
I
IDAPA 16.01.05.008 (40 CFR 264.16(a)( 1) and (c)
DOE Order 435.1
DOE Order 5400.5
IDAPA 16.01 .01.650, 16.01 .01.651
Personnel training Entire ICDF Complex
Radioactive waste Entire ICDF Complex management performance objectives to protect workers
Exposures to the public will be Entire ICDF Complex kept ALARA
Fugitive dust emissions Entire ICDF Complex
40 CFR 122.26 Storm water discharges during Entire ICDF Complex during construction construction
IDAPA 16.01.05.008 [40 CFR General inspection Entire ICDF Complex 264.15(a),(c)] requirements
IDAPA 16.01.05.008 [40 CFR Site security Entire ICDF Complex 264.14(a), (b), (c)]
16 USC 469 et seq. 36 CFR 65 Natrcnal Archeological and Entire ICDF Complex Historical Preservation Act
25USC 3001 Native American Graves Entire ICDF Complex Protection and Repatriation Act A
d
412.09 (02/16/2000
Technical and WAG 3 STAGING, STORAGE, STABILIZATION, Identifier: ‘TFR-17 Functional AND TREATMENT FACILITY Revision: 0 Requirements Page: 33 of 52
1. All ARARS are imposed by Table 12-3 of the ROD
Technical and Functional Requirements.
412.09 (02/16/2000 - Rev. 05)
WAG 3 STAGING, STORAGE, STABILIZATION, Identifier: TFR-17 AND TREATMENT FACILITY Revision: 0
Paee: 35 of 52
SSSTF/ICDF Complex Functional Block Flow
Diagram Block Number
1.3 Record Keeping
2.0 Storage and Staging Function
2.1 Off -load/load function
2.1 .l Solid Waste off- load/load area
ARAR
IDAPA 16.01.05.006 (40 CFR 262.11)
IDAPA 16.01.05.011 (40 CFR 268)
IDAPA 16.01.05.011 (40 CFR 268.49)
IDAPA 16.01.05.008 (40 CFR 264.309(a)and (b)
40 CFR 761.50(b)(7)
IDAPA 16.01.05.008 (40 CFR 264, Subpart I)
IDAPA 16.01.05.008 (40 CFR 264.192)
Description
Hazardous waste determination
Land disposal restrictions
Alternative LDR treatment All waste entering the complex standards for contaminated outside the WAG AOC except WAG 3 soils waste that triggered placement
Surveying and record keeping
PCB storage and disposal
Use and management of containers
Design and installation of new permanent tanks which contain tank svstems or components . hazardous waste
Applicable Unit
All waste entering the complex outside WAG 3 AOC
All waste entering the complex outside the WAG AOC except WAG 3 waste that triggered placement
Landfill cells, map location of waste by tvpe within each cell
PCB record keeping as referenced in 761.65(a)(2)(ii)(iii)
All containers containing hazardous waste
412.09
Technical and Functional Requirements
(02M/2000 - Rev. 05)
WAG 3 STAGING, STORAGE, STABILIZATION, Identifier: TFR-17 AND TREATMENT FACILITY Revision: 0
Page: 36 of 52
SSSTF/ICDF Complex Functional Block Flow
Diagram Block Number ARAR Description * Applicable Unit
IDAPA 16.01.05.008 (40 CFR Air emission standards for Tanks, and containers which have an 264.1082 through 1088) tanks and containers average VO concentration 2
500 ppmw at the point of waste origin
2.1..2 I. iquid Waste off- IDAPA 16.01.05.008 (40 CFR load/load area 264, Subpart I)
IDAPA 16.01.05.008 (40 CFR 264.1082 through 1088)
2.1.3 Reagent off-load area
Use and management of All containers which contain containers hazardous waste
Air emission standards for Tanks and containers which have an tanks, surface impoundments, average VO concentration 2 and containers 500 ppmw at the point of waste origin
None
2.2 External Storage and Staging Function _.. . 2.2.1 Disposal Staging IDAPA 16.01.05.008 (40 CFR Temporary units Tanks or containers in temporary Area 264.553) storage areas
IDAPA 16.01.05.008 (40 CFR Design and installation of new Permanent tanks which contain 264.192) tank systems or components hazardous waste
IDAPA 16.01.05.008 (40 CFR Remediation waste staging Solid, nonflowing remediation waste 264.554) piles that is not in a containment building
and is used only during remedial operations for temporary storage
IDAPA 16.01.05.008 (40 CFR Design and installation of new Permanent tanks which contain 264.192) tank systems or components hazardous waste
IDAPA 16.01.05.008 (40 CFR Use and management of All Containers which contain 264, Subpart I) containers hazardous waste
. 412.09
Technical and Functional Reauirements
(02/16/2000 - Rev. 05)
WAG 3 STAGING, STORAGE, STABILIZATION, Identifier: ,TFR-I7 AND TREATMENT FACILITY Revision: 0
Paee: 37 of 52
SSSTNICDF Complex Functional Block Flow
Diagram Block Number ARAR
* IDAPA 16.01.05.008 (40 CFR 264, Subpart DD)
40 CFR 761.50(b)(7)
Description I Applicable Unit
Containment buildings All buildings which contain hazardous waste
PC6 storage and disposal PCB storage requirements referenced in 761.65
IDAPA 16.01.05.008 (40 CFR 264.1082 through 1088)
IDAPA 16.01 .OS.uOS (40 CFR 264.601)
Air emission standards for Tanks and containers which have an tanks, surface impoundments, average VO concentration 2 and containers 500 ppmw at the point of waste origin
Miscellaneous units A hazardous waste management unit environmental performance where hazardous waste is treated, standards stored or disposed of and is not a
container, tank, surface impoundment, land treatment unit, landfill, incinerator, boiler, industrial furnace, underground injection well, containment building, corrective action management unit, R&D unit, or a permitted unit under 40 CFR 270.65 or a staging pile.
2.2.2 Treatment Staging Area
IDAPA 16.01.05.008 (40 CFR 264.553)
IDAPA 16.01.05.008 (40 CFR 264.192)
IDAPA 16.01.05.008 (40 CFR 264.554)
Temporary units Tanks or containers in temporary storage areas
Design and installation of new Permanent tanks which contain tank systems or components hazardous waste
Remediation waste staging Solid, nonflowing remediation waste piles that is not in a containment building
and is used only during remedial operations for temporary storage
412.09
Technical and Functional Reauirements
WAG 3 STAGING, STORAGE, STABILIZATION, Identifier: .TFR- 17 AND TREATMENT FACILITY Revision: 0
Paee: 38 of 52
SSSTFKDF Complex Functional Block Flow
Diagram Block Number
2.2.3 Liquid waste staging area
ARAR IDAPA 16.01.05.008 (40 CFR 264, Subpart I)
IDAPA 16.01.05.008 (40 CFR 264, Subpart DD)
IDAPA 16.01.05.008 (40 CFR 264.1082 through 1088)
IDAPA 16.01.05.008 (40 CFR 264.601)
IDAPA 16.01.05.008 (40 CFR 264.553)
IDAPA 16.01.05.008 (40 CFR 264.192)
IDAPA 16.01.05.008 (40 CFR 264. Subbart I)
Description
Use and management of containers
Containment buildings
Air emission standards for tanks, surface impoundments, and containers
Miscellaneous units environmental performance standards
Temporary units
Design and installation of new tank systems or components
Use and management of containers
Applicable Unit
All Containers that contain hazardous waste
All buildings that contain hazardous waste
Tanks and containers which have an average VO concentration 3 500 ppmw at the point of waste origin
A hazardous waste management unit where hazardous waste is treated, stored or disposed of and is not a container, tank, surface impoundment, land treatment unit, landfill, incinerator, boiler, industrial furnace, underground injection well, containment building, corrective action management unit, R&D unit, or a permitted unit under 40 CFR 270.65 or a staging pile.
Tanks or containers in temporary areas storage
Permanent tanks which contain hazardous waste
All Containers that contain hazardous waste
Technical and WAG 3 STAGING, STORAGE, STABILIZATION, \“LI ,“,Luuv - n\c;v. “J,
Identifier: .TFR-17 Functional AND TREATMENT FACILITY Revision: 0 Requirements Page: 39 of 52
SSSTWICDF Complex Functional Block Flow
Diagram Block Number ARAR Description Applicable Unit
IDAPA 16.01.05.008 (40 CFR Containment buildings All buildings that contain hazardous 264, Subpart DD) waste
40 CFR 76i .50(b)(7) PCB storage and disposal PCB storage requirements referenced in 761.65
IDAPA 16.01.05.008 (40 CFR Air emission standards for Tanks and containers which have an 264.1082 through 1088) tanks, surface impoundments, average VO concentration 2
and containers 500ppmw at the point of waste origin
IDAPA 16.01.05.008 (40 CFR Miscellaneous units A hazardous waste management unit 264.601) environmental performance where hazardous waste is treated,
standards stored or disposed of and is not a container, tank, surface impoundment, land treatment unit, landfill, incinerator, boiler, industrial furnace, underground injection well, containment building, corrective action management unit, R&D unit, or a permitted unit under 40 CFR 270.65 or a staging pile.
2.2.4 Empty waste IDAPA 16.01.05.008 (40 CFR Use and management of All containers that contain hazardous container 264, Subpart I) containers waste storage/staging area
IDAPA 16.01.05.008 (40 CFR Air emission standards for Tanks, and containers which have an 264.1082 through 1088) tanks, surface impoundments, average VO concentration 2
and containers 500 ppmw at the point of waste origin
2.3 Internal Storage and Staging Function
412.09
Technical and Functional Reauirements
WAG 3 STAGING, STORAGE, STABILIZATION, AND TREATMENT FACILITY
Identifier: .TFR- 17 Revision: 0 Pane: 40 of 52
SSSTWICDF Complex Functions I Wock Flow
Diagram Block Number ARAR Description Applicable Unit
2.3.1 Disposal Staging * IDAPA 16.01.05.008 (40 CFR Temporary units Tanks or containers in temporary area 264.553) storage areas
. IDAPA 16.01.05.008 (40 CFR 264.192) . . ._ -. IDAPA 16.01.05.008 (40 CFR 264.554)
Design and installation of new Permanent tanks which contain tank systems or components hazardous waste
Re.yediation waste staging Solid, non-flowing remediation waste piles that is not in a containment building
and is used only during remedial operations for temporary storage
IDAPA 16.01.05.008 (40 CFR Use and management of All containers which contain 264, Subpart I) -containers hazardous waste
IDAPA 16.01.05.008 (40 CFR Containment buildings All buildings which contain hazardous 264, Subpart DD) waste
IDAPA 16.01.05.008 (40 CFR Air emission standards for Tanks and containers which have an 264.1082 through 1088) tanks, surface impoundments, average VO concentration 2
and containers 500 ppmw at the point of waste origin
IDAPA 16.01.05.008 (40 CFR Miscellaneous units A hazardous waste management unit 264.601) environmental performance where hazardous waste is treated,
standards stored or disposed of and is not a container, tank, surface impoundment, land treatment unit, landfill, incinerator, boiler, industrial furnace, underground injection well, containment building, corrective action management unit, R&D unit, or a permitted unit under 40 CFR 270.65 or a staging pile.
, ”
412.09
Technical and Functional Requirements
WAG 3 STAGING, STORAGE, STABILIZATION, AND TREATMENT FACILITY
Identifier: Revision: Page:
(02AG/2000 - Rev. 05)
,TFR-17 0 41 of 52
SSSTF/ICDF Complex Functional Block Flow
Diagram Block Number
2.3.2 Treatment Staging Area
ARAR
IDAPA 16.01.05.008 (40 CFR 264.553)
IDAPA 16.01.05.008 (40 CFR Design and installation of new 264.192) tank svstems or combonents
IDAPA 16.01.05.008 (40 CFR 264.554)
IDAPA 16.01.05.008 (40 CFR 264, Subpart I)
IDAPA 16.01.05.008 (40 CFR 264, Subpart DD)
IDAPA 16.01.05.008 (40 CFR 264.1082 through 1088)
Description
Temporary units
Remediation waste staging piles
Use and management of containers
Containment buildings
Air emission standards for tanks, surface impoundments, and containers
Applicable Unit
Tanks or containers in temporary storage areas
Permanent tanks which contain hazardous waste
Solid, nonflowing remediation waste that is not in a containment building and is used only during remedial operations for temporary storage
All containers which contain hazardous waste
All buildings which contain hazardous waste
Tanks and containers which have an average VO concentration 1 500 ppmw at the point of waste origin
Technical and Functional Reauirements
WAG 3 STAGING, STORAGE, STABILIZATION, AND TREATMENT FACILITY
412.W
]I
SSSTWICDF Complex Functional Block Flow
Diagram Block Number .ARAR Description Applicable Unit
IDAPA 16.01.05.008 (40 CFR Miscellaneous units A hazardous waste management unit 264.601) environmental performance where hazardous waste is treated,
standards stored or disposed of and is not a container, tank, surface impoundment, land treatment unit, landfill, incinerator, boiler, industrial furnace, underground injection well, containment building, corrective action management unit, R&D unit, or a permitted unit under 40 CFR 270.65 or a staging pile.
2.3.3 Special Waste IDAPA 16.01.05.008 (40 CFR Temporary units Tanks or containers in temporary Storage/staging area 264.553) storage areas
IDAPA 16.01.05.008 (40 CFR Design and installation of new Permanent tanks which contain 264.192) tank systems or components hazardous waste
IDAPA 16.01.05.008 (40 CFR Remediation waste staging Solid, nonflowing remediation waste 264.554) piles that is not in a containment building
and is used only during remedial operations for temporary storage
40 CFR 761.50(b)(7) PCB storage and disposal PCB storage requirements referenced in 761.65
IDAPA 16.01.05.008 (40 CFR 264, Subport I) I _ ,. IDAPA 16.01.05.008 (40 CFR 264, Subpart DD)
Use and management of containers
Containment buildings
All Containers which contain hazardous waste
All buildings which contain hazardous waste
412.09
Technical and Functional Requirements
WAG 3 STAGING, STORAGE, STABILIZATION, Identifier: .TFR- 17 AND TREATMENT FACILITY Revision: 0
Page: 43 of 52
SSSTF/ICDF Complex Functional Block Flow
Diagram Block Number ARAR
IDAPA 16.01.05.008 (40 CFR 264.1082 through 1088)
. IDAPA 16.01.05.008 (40 CFR 264.601)
+ I
2.3.4 Reagent Storage Area
3.0 Waste Treatment Function
3.1 Packaging for Off- IDAPA 16.01.05.008 (40 CFR Site Disposal 264.553)
IDAPA 16.01.05.008 (40 CFR 264.192)
Description Applicable Unit
Air emission standards for tanks, surface impoundments, and containers
Miscellaneous units environmental performance standards
None
Temporary units
Design and installation of new tank systems or components
Tanks and containers which have an average VO concentration 2 500 ppmw at the point of waste origin
A hazardous waste management unit where hazardous waste is treated, stored or disposed of and is not a container, tank, surface impoundment, land treatment unit, landfill, incinerator, boiler, industrial furnace, underground injection well, containment building, corrective action management unit, R&D unit, or a permitted unit under 40 CFR 270.65 or a staging pile.
Tanks or containers in temporary storage areas
Permanent tanks which contain hazardous waste
412.W (021W2000 - Rev. 05)
Technical and WAG 3 STAGING, STORAGE, STABILIZATION, Identifier: ,TFR- I7 Functional AND TREATMENT FACILITY Revision: 0 Requirements Page: 44 of 52
\ SSSTF/ICDF Complex Fur rctional Block Flow
Diagram Block Number ARAR Description Applicable Unit
IDAPA 16.01.05.008 (40 CFR Remediation waste staying Solid, nonflowing remediation waste 264.554) piles that is not in a containment building
and is used only during remedial operations for temporary storage
IDAPA 16.01.05.008 (40 CFR Use and management of All containers which contain 264, Subpart I) containers hazardous waste
IDAPA 16.01.05.008 (40 CFR Containment buildings All buildings which contain hazardous 264, Subpart DD) waste
IDAPA 16.01.05.008 (40 CFR Air emission standards for Tanks and containers which have an 264.1082 through 1088) tanks, surface impoundments, average VO concentration 3
and containers 500 ppmw at the point of waste origin
3.2 Secondary Waste IDAPA 16.01.05.008 (40 CFR Temporary units Tanks or containers in temporary Storage 264.553) storage areas -.. .-
IDAPA 16.01.05.008 (40 CFR Design and installation of new Permanent tanks which contain 264.192) tank systems or components hazardous waste
IDAPA 16.01.05.008 (40 CFR Remediation waste staging Solid, non-flowing remediation waste 264.554) piles that is not in a containment building
and is used only during remedial operations for temporary storage
IDAPA 16.01.05.008 (40 CFR Use and management of All Containers which contain 264, Subpart I) containers hazardous waste
IDAPA 16.01.05.008 (40 CFR Containment buildings All buildings which contain hazardous 264, Subpart DD) waste
412.09
Technical and WAG 3 STAGING, STORAGE, STABILIZATION, Identifier: ,TFR-17 Functional AND TREATMENT FACILITY Revision: 0 Requirements Page: 45 of 52
SSSTF/ICDF Complex Functional Block Flow
Diagram Block Number ARAR Description Applicable Unit
IDAPA 16.01.05.008 (40 CFR Air emission standards for Tanks and containers which have an 264.1082 through 1088) tanks, surface impoundments, average VO concentration 2
and containers 500 ppmw at the point of waste origin
3.3 Waste Sizing IDAPA 16.01.05.008 (40 CFR Miscellaneous units 264.601)
A hazardous waste management unit environmental performance where hazardous waste is treated, star. Jards stored or disposed of and is not a
container, tank, surface impoundment, land treatment unit, landfill, incinerator, boiler, industrial furnace, underground injection well, containment building, corrective action management unit, R&D unit, or a permitted unit under 40 CFR 270.65 or a staging pile.
IDAPA 16.01.05.008, (40 CFR Use and management of All Containers which contain 264, Subpart I) containers hazardous waste
3.4 Treatment Staging IDAPA 16.01.05.008 (40 CFR Temporary units 264.553)
Tanks or containers in temporary storage areas
IDAPA 16.01.05.008 (40 CFR Design and installation of new Permanent tanks that contain 264.192) tank systems or components hazardous waste IDAPA 16.01.05.008 (40 CFR Remediation waste staging 264.554) piles
Solid, nonflowing remediation waste that is not in a containment building and is used only during remedial operations for temporary storage
IDAPA 16.01.05.008 (40 CFR Use and management of All Containers which contain . 264, Subpart I) containers hazardous waste
Technical and Functional Requirements
WAG 3 STAGING, STORAGE, STABILIZATION, AND TREATMENT FACILITY
Identifier: Revision: Page:
412.09 (02/16/2000- Rev.051
*TFR- 17 0 46 of 52
SSSTF/ICDF Complex Funclii:)nal Block Flow
.
Dia ram Block Number
I
3.5 Solid Waste Treatment
ARAR
IDAPA 16.01.05.008 (40 CFR 264, Subpart DD)
IDAPA 16.01.05.008 (40 CFR 264.1082 through 1088)
IDAPA 16.01.05.008 (40 CFR Design and installation of new 264.192) tank systems or components
IDAPA 16.01.05.008 (40 CFR 264.601)
IDAPA 16.01.05.008 (40 CFR 264Suboart I)
IDAPA 16.01.05.008 (40 CFR 264, Subpart DD)
-. Description _..- _- Containmel tt buildings
Air emission standards for tanks, surface impoundments, and containers
Miscellaneous units environmental performance standards
Use and management of containers
Containment buildings
___- Applicable Unit
All buildings which contain hazardous waste
Tanks and containers which have an average VO concentration 2 500 ppmw at the point of waste origin
Permanent tanks that contain hazardous waste
A hazardous waste management unit where hazardous waste is treated, stored or disposed of and is not a container, tank, surface impoundment, land treatment unit, landfill, incinerator, boiler, industrial furnace, underground injection well, containment building, corrective action management unit, R&D unit, or a permitted unit under 40 CFR 270.65 or a staging pile.
All Containers which contain hazardous waste
All buildings which contain hazardous waste
412.09
Technical and Functional Requirements
WAG 3 STAGING, STORAGE, STABILIZATION, AND TREATMENT FACILITY
Identifier: Revision: Page:
,TFR-17 0 47 of 52
SSSTF/ICDF Complex Functional Block Flow
Diagram Block Number ARAR Description Applicable Unit
IDAPA 16.01.05.008 (40 CFR Air emissions standards for Transport Equipment, SSSTF process 264.1052 through 1062) equipment leaks equipment that contains or contacts
hazardous waste with organic concentrations of at least 10% by weight.
IDAPA 16.01.05.008 (40 CFR Air emission standards for Tanks and containers which have an 264.1082 through 1088) tanks, surface impoundments, average VO concentration 2
and containers 500ppmw at the point of waste origin
IDAPA 16.01.05.011 (40 CFR Land disposal restrictions 268)
All waste entering the complex outside the WAG AOC except WAG 3 waste that triggered placement
IDAPA 16.01.05.011 (40 CFR Alternative LDR treatment 268.49)
All waste entering the complex standards for contaminated outside the WAG AOC except WAG 3 soils waste that triggered placement
40 CFR 761.50(a)(5) PCB ,disposal requirements Disposal of non-liquid PCBs may avoid otherwise applicable sampling requirements by presuming that the
40 CFR 761.50(b)(3) PCB remediation waste
40 CFR 761.50(b)(7) PCB Radioactive Waste
PCBs disposed of are 2 500 ppm( or greater that lOOpg/cm* )if no free flowing liquids are present
PCB Remediation waste including Sludge 2 50 ppm
PCB Radioactive Waste 150 ppm
Technical and WAG 3 STAGING, STORAGE, STABILIZATION, Functional AND TREATMENT FACILITY Requirements . .
SSSTF/ICDF Complex Functional Block Flow
Diagram Block Number
3.6 Liquid Waste Treatment
ARAR
40 CFR 761.50(b)(8)
40 CFR 761.50(d)(4)
IDAPA 16.01.05.008 (40 CFR 264.192)
IDAPA 16.01.05.008 (40 CFR 264.601)
IDAPA 16.01.05.008 (40 CFR 264, Subpart I)
IDAPA 16.01.05.008 (40 CFR 264, Subpart DD)
IDAPA 16.01.05.008 (40 CFR 264.1052 through 1062)
412.O!l
]I
DescriDtiOn
Porous surfaces
Disposal requirements for PCBS
Design and installation of new tank svstems or combonents
Miscellaneous units environmental performance standards
Use and management of containers
Containment buildings
Air emissions standards for eauioment leaks
Applicable Unit
Porous surfaces contaminated with PCBs
Landfill cells - . I .
per 1.1 I:~I lent tanks which car Ilain hazardous waste
A hazardous waste management unit where hazardous waste is treated, stored or disposed of and is not a container, tank, surface impoundment, land treatment unit, landfill, incinerator, boiler, industrial furnace, underground injection well, containment building, corrective action management unit, R&D unit, or a permitted unit under 40 CFR 270.65 or a staging pile.
All containers that contain hazardous waste
All buildings that contain hazardous waste
Transport equipment, SSSTF process eauioment
.
Technical and Functional Requirements
WAG 3 STAGING, STORAGE, STABILIZATION, AND TREATMENT FACILITY
Identifier: Revision: Page:
412.09 (02/ ICY2000 - Rev. 05)
,TFR-17 0 49 of 52
SSSTFKDF Complex Functional Block Flow
Diagram Block Number ARAR Description Applicable Unit
IDAPA 16.01.05.008 (40 CFR Air s;mission standards for Tanks, and containers which have an 264.1082 through 1088) tanks, surface impoundments, average VO concentration 2
and containers 500ppmw at the point of waste origin
IDAPA 16.01.05.011 (40 CFR Land disposal restrictions All waste entering the complex 268) outside the WAG AOC except WAG 3
waste that triggered placement
IDAPA 16.01.05.011 (40 CFR Alternative LDR treatment All waste entering the complex 268.49) standards for contaminated outside the WAG AOC except WAG 3
soils waste that triggered placement
40 CFR 761.50(a)(5) PCB disposal requirements Disposal of non-liquid PCBs may avoid otherwise applicable sampling requirements by presuming that the PCBs disposed of are > 500 ppm( or greater that 100 pg/cmT )if no free flowing liquids are present
40 CFR 761.50(b)(3) PCB remediation waste PCB Remediation waste including , Sludge 2 50 ppm
40 CFR 761.50(b)(7) PCB radioactive waste PCB Radioactive Waste 2 50 ppm
40 CFR 761.50(b)(8) Porous surfaces Porous surfaces contaminated with PCBs
3.7 Reagent Makeup
40 CFR 761.50(d)(4) Disposal requirements for PCBs
None
Landfill cells
412.W
Technical and (02/I6/2000 - Rev. 05)
1 WAG 3 STAGING, STORAGE, STABILIZATION, 1 Identifier: ,TFR-17 1 Functional Requirements
AND TREATMENT FACILITY Revision: 0 Page: 50 of 52
SSSTWICDF Complex Functional Block Flow
Diagram Block Number
4.0 Decontamination Function
4.1 Decontamination Area
4.2 Solids Collection
ARAR
IDAPA 16.01.05.008 (40 CFR 264.114)
40 CFR 761.79(a) and (b)
IDAPA 16.01.05.008 (40 CFR 264.192)2
IDAPA 16.01.05.008 (40 CFR 264.1082 through 1088)l
IDAPA 16.01.05.008 (40 CFR 264.192)’
Description
Disposal and decontamination of equipment, structures, and soils
PCB container and moveable equipment decontamination requirements
-_I_-
Design and installation til ricw tank systems or components
Air emission standards for tanks, surface impoundments, and containers
Surface Impoundment design and operating requirements
Apblicable Unit
All contaminated equipment structures and soils
Any container or equipment that has been contaminated with PCBs and are regulated for disposal from water, organic liquids, non-porous surfaces (including scrap metal from disassembled electrical equipment) concrete, and non-porous surfaces covered with a porous surface, such as paint or coatina on metal.
Permanent tanks which contain hazardous waste
Tanks, and containers which have an average VO concentration 3 500ppmw at the point of waste origin
Surface impoundment
2. May be applicable dependent on design
Technical and
412.09 (OUl6/2000 - Rev. 05)
WAG 3 STAGING, STORAGE, STABILIZATION, 1 Identifier: ,TFR- 17 1 Functional AND TREATMENT FACILITY JR evision: Requirements 1 Page:
1 rable 3.1.4-2 OTHER DESIGN STANDARDS Alternative/ARARs citation
DOE Order 435.1
Description Applies To
Radioactive waste management Worker protection performance objectives to protect workers
DOE Order 5400.5 Exposures to the public will be Exposures to public keot ALARA and workers
10 CFR 835
40 CFR 300.440
DOE Order 5007.6C
DOE - ID Architectural Engineering Standards
29 CFR 1910.120
Occupational radiation protection Workers
Off site rule Waste locations
Qualitv assurance Waste acceptance
Hazard communication
Constructions
Workers
29 CFR 1926 Safety and health regulations for construction
Workers
Imposed By
ROD - Page 12-l 7
ROD - Page 12-l 7
ROD Page 11-3
ROD Page 1 l-l 5
FFA/CO Section xvi
DOE Contract
DOE Contract
DOE Contract