407298 ds iwap107 aruba ap274 datasheet
2
A 407298-1.0 This iWAP107 is an ATEX and IECEx approved Zone 1 Access Point Enclosure which contains Aruba’s high performance AP- 274 access point. This new system incorporates Aruba’s latest technology which conforms to 802.11n/ac standards. Six antennas are utilised, allowing the MIMO functionality of the latest access points to be implemented, providing optimum coverage and maximum data throughput on Chemical Plants, Oil Refineries or Oil & Gas Platforms. The intrinsically safe RF outputs of the iWAP107 allows users to choose any antenna for use with their wireless hardware e.g. Extronics iANT2xx range of high quality rugged outdoor antennas. Any antennas not listed in the Extronics range must be assessed by the user to ensure they meet the requirements for installation of non-electrical equipment in hazardous areas. Each unit contains surge arrestors for lightning suppression in outdoor installations, with the option of single mode or multimode fibre optic inputs to allow for extended Ethernet link distance. Overview Features and Benefits iWAP107-AP274 Zone 1 Wireless Access Point Specification Copyright © Extronics Ltd 2014. The information contained in this document is subject to change without notice. Extronics cannot be held responsible for any errors or inaccuracies within this document. *Any antennas not listed in the Extronics range must be assessed by the user to ensure they meet the requirements for installation of non-electrical equipment in hazardous areas. Zone 1 Explosion Proof Wireless Access Point enclosure system with intrinsically safe RF outputs. II 2(1) GD Ex d [ia IIC Ga] IIB+H 2 T5 Gb Ex tb [ia Da] IIIC T100°C Db Galvanically Isolated RF Outputs Non-certified antennas can be used with chosen wireless hardware* Extended Temperatures Operating temperature range of -20°C to +50°C for the most extreme environments. Future Proof Infrastructure As new hardware becomes available it can be assessed by Extronics for compliance to the certification. The existing hardware can then be replaced with the new version meaning the user is installing a future proof solution. Gigabit Ethernet Supports 100/1000Base-T/FX/LX options to offer a significant increase in speed over the older fast Ethernet standard. MIMO Radio Offers increased data throughput and higher immunity to signal interference for optimal performance in challenging industrial environments. Certification Type II 2 (1)GD Ex d [ia IIC Ga] IIB+H 2 T5 Gb II 2 (1)GD Ex tb [ia Da] IIIC T100°C Db Power Supply Universal 90-264VAC / IEEE802.3at PoE Maximum Power Consumption Basic configuration: 23W With fibre: 27W Enclosure Material Marine grade copper free aluminium light alloy, epoxy powder coated or 316L Stainless Steel (optional) Ingress Protection IP66 Weight Aluminium—Approx 30kg (hardware dependant) 316L Stainless Steel—Approx 70kg (hardware dependant) Dimensions Aluminium— 415 x 315 x 250 mm (w x h x d) 316L Stainless Steel— 415 x 315 x 253 mm (w x h x d) Environmental Ambient temperature: -20ºC to +50ºC Relative humidity; 0 to 95%, non condensing Input Connections - AC power input screw terminals - 10/100/1000Base-T Ethernet on RJ45 socket - Single or Multi mode fibre input on LC connector & Splice Tray (entry via M20x1.5-6H drilled entries) Ethernet Link distance 10/100/1000BASE-T Ethernet on CAT5e: up to 100m 100BASE-FX Multi Mode fibre : up to 2km, wavelength 1310nm 100BASE-LX10 Single mode fibre: up to 10km, wavelength 1310nm 1000BASE-LX Multi Mode fibre : up to 550m, wavelength 1310nm 1000BASE-LX10 Single mode fibre: up to 10km, wavelength 1310nm Output Connection Six galvanically isolated N-Type RF outputs Internal RF Losses (typical) 2.7dB @2.4GHz 3.6dB @5GHz Certification ATEX: TRAC14ATEX0022X IECEx: TRC 14.0010X NEC 500 - C1 D1: Pending Extronics Ltd., 1 Dalton Way, Midpoint 18, Middlewich, Cheshire, UK. CW10 0HU Tel: +44 (0) 845 277 5000 Fax: +44 (0)845 277 4000 E-mail: [email protected] Web: www.extronics.com
-
Upload
chris-easy -
Category
Documents
-
view
32 -
download
6
Transcript of 407298 ds iwap107 aruba ap274 datasheet
A
407298-1.0
This iWAP107 is an ATEX and IECEx approved Zone 1 Access Point Enclosure which contains Aruba’s high performance AP-274 access point. This new system incorporates Aruba’s latest technology which conforms to 802.11n/ac standards. Six antennas are utilised, allowing the MIMO functionality of the latest access points to be implemented, providing optimum coverage and maximum data throughput on Chemical Plants, Oil Refineries or Oil & Gas Platforms. The intrinsically safe RF outputs of the iWAP107 allows users to choose any antenna for use with their wireless hardware e.g. Extronics iANT2xx range of high quality rugged outdoor antennas. Any antennas not listed in the Extronics range must be assessed by the user to ensure they meet the requirements for installation of non-electrical equipment in hazardous areas. Each unit contains surge arrestors for lightning suppression in outdoor installations, with the option of single mode or multimode fibre optic inputs to allow for extended Ethernet link distance.
Overview
Features and Benefits
iWAP107-AP274 Zone 1 Wireless Access Point
Specification
Copyright © Extronics Ltd 2014. The information contained in this document is subject to change without notice. Extronics cannot be held responsible for any errors or inaccuracies within this document.
*Any antennas not listed in the Extronics range must be assessed by the user to ensure they meet the requirements for installation of non-electrical equipment in hazardous areas.
Zone 1 Explosion Proof Wireless Access Point enclosure system with intrinsically safe RF outputs.
II 2(1) GD
Ex d [ia IIC Ga] IIB+H2 T5 Gb
Ex tb [ia Da] IIIC T100°C Db
Galvanically Isolated RF Outputs Non-certified antennas can be used with chosen wireless hardware* Extended Temperatures Operating temperature range of -20°C to +50°C for the most extreme environments. Future Proof Infrastructure As new hardware becomes available it can be assessed by Extronics for compliance to the certification. The existing hardware can then be replaced with the new version meaning the user is installing a future proof solution. Gigabit Ethernet Supports 100/1000Base-T/FX/LX options to offer a significant increase in speed over the older fast Ethernet standard. MIMO Radio Offers increased data throughput and higher immunity to signal interference for optimal performance in challenging industrial environments.
Certification Type II 2 (1)GD Ex d [ia IIC Ga] IIB+H2 T5 Gb II 2 (1)GD Ex tb [ia Da] IIIC T100°C Db
Power Supply Universal 90-264VAC / IEEE802.3at PoE
Maximum Power Consumption
Basic configuration: 23W With fibre: 27W
Enclosure Material Marine grade copper free aluminium light alloy, epoxy powder coated or 316L Stainless Steel (optional)
Ingress Protection IP66
Weight Aluminium—Approx 30kg (hardware dependant) 316L Stainless Steel—Approx 70kg (hardware dependant)
Dimensions Aluminium— 415 x 315 x 250 mm (w x h x d) 316L Stainless Steel— 415 x 315 x 253 mm (w x h x d)
Environmental Ambient temperature: -20ºC to +50ºC Relative humidity; 0 to 95%, non condensing
Input Connections - AC power input screw terminals - 10/100/1000Base-T Ethernet on RJ45 socket - Single or Multi mode fibre input on LC connector & Splice Tray (entry via M20x1.5-6H drilled entries)
Ethernet Link distance
10/100/1000BASE-T Ethernet on CAT5e: up to 100m 100BASE-FX Multi Mode fibre : up to 2km, wavelength 1310nm 100BASE-LX10 Single mode fibre: up to 10km, wavelength 1310nm 1000BASE-LX Multi Mode fibre : up to 550m, wavelength 1310nm 1000BASE-LX10 Single mode fibre: up to 10km, wavelength 1310nm
Output Connection Six galvanically isolated N-Type RF outputs
Internal RF Losses (typical)
2.7dB @2.4GHz 3.6dB @5GHz
Certification ATEX: TRAC14ATEX0022X IECEx: TRC 14.0010X NEC 500 - C1 D1: Pending
Extronics Ltd., 1 Dalton Way, Midpoint 18, Middlewich, Cheshire, UK. CW10 0HU
Tel: +44 (0) 845 277 5000 Fax: +44 (0)845 277 4000 E-mail: [email protected] Web: www.extronics.com
iWAP107-AP274 - Zone 1 Approved Aruba Wireless Access Point Description Order Code
Zone 1 AP, AC / PoE powered, 100/1000Base-T Ethernet, 6 x galvanically isolated RF outputs iWAP107-AP274-C Zone 1 AP, AC / PoE powered, Multimode 1000BASE-LX fibre with LC connector, 6 x galvanically isolated RF outputs iWAP107-AP274-FG Zone 1 AP, AC / PoE powered, Single mode 1000BASE-LX10 fibre with LC connector, 6 x galvanically isolated RF outputs iWAP107-AP274-SG
Accessories
Stainless Steel 316L Enclosure Pipe mount bracket kit for iWAP107 Enclosure iWAPMB02 to fit 1.5” - 2” diameter pipe or rectangular post. Stainless Steel enclosure supplement for iWAP107 enclosure K010422
Antenna Locations
Remote Mount - 6 antennas plus Data & Power outlets*
Ordering Information
Extronics Ltd., 1 Dalton Way, Midpoint 18, Middlewich, Cheshire, UK. CW10 0HU
Tel: +44 (0) 845 277 5000 Fax: +44 (0)845 277 4000 E-mail: [email protected] Web: www.extronics.com
*If direct mount antennas are required, then an alternative antenna location pattern will be required on the enclosure - contact Extronics for details.
