4020PL10 4020PL23 4020PL41 4020PL75P0440 P0427 P0431 P0202 Valve Body Mounting Hardware Aerator...

4
ESTATE SERIES TOWER COLLECTION ESTATE SERIES TOWER COLLECTION # PART PART DESCRIPTION DESCRIPTION PART # PART # 1 2 3 4 5 6 7 8 9 10 10 11 11 12 12 13 13 14 14 15 15 16 16 Complete Spout Assembly * Complete Spout Assembly * PM-400 PM-400 * Please specify the finish when ordering the part. * Please specify the finish when ordering the part. KEEP THIS INSTRUCTION BOOKLET FOR FUTURE REFERENCE 17 17 WIDESPREAD FAUCET WITH “PL” HANDLES WIDESPREAD FAUCET WITH “PL” HANDLES 18 18 Complete PL Lever Handle Complete PL Lever Handle Assembly * Assembly * Hot Cartridge Only Hot Cartridge Only Cold Cartridge Only Cold Cartridge Only Complete Hot Valve Complete Hot Valve Complete Cold Valve Complete Cold Valve Connecting Hose to the Tee Connecting Hose to the Tee Connecting Hose to the Supply Connecting Hose to the Supply Line Line Tee Connector Tee Connector Spout Mounting Hardware Spout Mounting Hardware Washer for the Tee Connector Washer for the Tee Connector Lift Knob* Lift Knob* Complete Pop-Up * Complete Pop-Up * 00PL 00PL P0418 P0418 P0419 P0419 P0466 P0466 P0467 P0467 P0441 P0441 P0440 P0440 P0427 P0427 P0431 P0431 P0202 P0202 Valve Body Mounting Hardware Valve Body Mounting Hardware Aerator Washer Aerator Washer Aerator Basket with Restrictor Aerator Basket with Restrictor PM-510 PM-510 PM-320 PM-320 Aerator Housing * Aerator Housing * P0944-U P0944-U 12 12 10 10 8 11 11 6 5 4 16 16 17 17 2 19 19 7 1 9 15 15 4020PL10 14 14 13 13 3 10 10 13 13 18 18 19 19 INSPECTED BY Rubber Washer Rubber Washer PS-2ET00-XA PS-2ET00-XA P0254 P0254 P02645 P02645 Lift Rod * Lift Rod * 20 20 P02646 P02646 Lift Rod Extension * Lift Rod Extension * 20 20 2 2 TOOLS THAT YOU MAY NEED PLEASE READ THE INSTRUCTIONS COMPLETELY BEFORE BEGINNING THE INSTALLATION. 3 4020PL23 4020PL41 4020PL75 PAGE 01 MODEL NUMBER

Transcript of 4020PL10 4020PL23 4020PL41 4020PL75P0440 P0427 P0431 P0202 Valve Body Mounting Hardware Aerator...

Page 1: 4020PL10 4020PL23 4020PL41 4020PL75P0440 P0427 P0431 P0202 Valve Body Mounting Hardware Aerator Washer Aerator Basket with Restrictor PM-510 PM-320 Aerator Housing * P0944-U 12 10

ESTATE SERIES TOWER COLLECTIONESTATE SERIES TOWER COLLECTION

## PARTPART DESCRIPTIONDESCRIPTION PART #PART #

11

22

33

44

55

66

77

8899

1010

1111

1212

1313

1414

1515

1616

Complete Spout Assembly *Complete Spout Assembly *

PM-400PM-400

* Please specify the finish when ordering the part.* Please specify the finish when ordering the part.

KEEP THIS INSTRUCTION BOOKLET FOR FUTURE REFERENCE

1717

WIDESPREAD FAUCET WITH “PL” HANDLESWIDESPREAD FAUCET WITH “PL” HANDLES

1818

Complete PL Lever HandleComplete PL Lever Handle Assembly *Assembly *

Hot Cartridge OnlyHot Cartridge Only

Cold Cartridge OnlyCold Cartridge Only

Complete Hot ValveComplete Hot Valve

Complete Cold ValveComplete Cold Valve

Connecting Hose to the TeeConnecting Hose to the Tee

Connecting Hose to the SupplyConnecting Hose to the Supply LineLine

Tee ConnectorTee Connector

Spout Mounting HardwareSpout Mounting Hardware

Washer for the Tee ConnectorWasher for the Tee Connector

Lift Knob* Lift Knob*

Complete Pop-Up *Complete Pop-Up *

00PL00PL

P0418P0418

P0419P0419

P0466P0466

P0467P0467

P0441P0441

P0440P0440

P0427P0427

P0431P0431

P0202P0202

Valve Body Mounting HardwareValve Body Mounting Hardware

Aerator WasherAerator Washer

Aerator Basket with RestrictorAerator Basket with Restrictor

PM-510PM-510

PM-320PM-320

Aerator Housing *Aerator Housing * P0944-UP0944-U

1212

1010

88

1111

6655 44

1616

171722 1919

77

11

99

1515

4020PL10

1414

1313

33

1010

1313

1818

1919

INSPECTED BY

Rubber WasherRubber Washer

PS-2ET00-XAPS-2ET00-XA

P0254P0254

P02645P02645Lift Rod * Lift Rod *

2020 P02646P02646Lift Rod Extension *Lift Rod Extension *

2020

22 22

TOOLS THAT YOU MAY NEED

PLEASE READ THE INSTRUCTIONS COMPLETELYBEFORE BEGINNING THE INSTALLATION.

33

4020PL234020PL41 4020PL75

PAGE 01

MODEL NUMBER

Page 2: 4020PL10 4020PL23 4020PL41 4020PL75P0440 P0427 P0431 P0202 Valve Body Mounting Hardware Aerator Washer Aerator Basket with Restrictor PM-510 PM-320 Aerator Housing * P0944-U 12 10

INSTALLATION INSTRUCTIONS

1. SPOUT INSTALLATION

A- Remove the tee connector (11), spout mounting hardware (4) and tee connector washer (12) from the bottom of the spout assembly. Apply a ring of silicone caulking around the center hole on the top of the sink. (Do not use plumbers' putty which can damage the spout finish).

- From the top of the deck, insert the spout's threaded shank with the lift rod (19) and knob (14) through the center hole of the sink.

B- Slip the spout mounting hardware (4) back onto the spout. First the notched rubber washer, then the notched metal washer, wing nut and the last the brass lock nut. Hand tighten the lock nut. - Attach the lift rod extension (21) to the lift rod (20). Make sure the lift rod operates smoothly. Adjust it if necessary.

C- Align the spout and secure the spout to the counter by tightening the 2 screws on the wing nut.

- Place the tee connector washer (12) into the tee connector (11) and thread on the tee connector at the end of the spout shank. Tighten to seal.

FLUSH BOTH SUPPLY LINES BEFORE INSTALLATION.

AFTER FLUSHING , SHUT OFF BOTH SUPPLY LINES.

MINIMUM HOLE SIZE FOR THE SPOUT AND HANDLE TRIM IS 1 ¼” AND MAXIMUM OF 1 ½”

2. HANDLE TRIM INSTALLATION

HANDLE TRIMS ARE READY FOR SIMPLE DROP IN INSTALLATION. DO NOT DISASSEMBLE.

A- Remove the valve body mounting hardware (13) from the valve body.

- Make sure the handle with the “cold” blue label (8) is installed at the right side of the spout (looking from the front) and the handle with the “hot” red label (7) at the left side of the spout.

- Apply a ring of silicone caulking around the handle hole on the sink top. (Do not use plumbers' putty which can damage the finish of the faucet). - Slip the valve body’s flexible hoses from the top of the sink or counter through the appropriate hole next to the spout. Aim the tee connecting hoses (9) toward the tee connector (11).

Notched rubber washerNotched metal washerWing Nut

Brass lock nut

SANTEC SANTEC

rubber washer

rubber washer

Lift Knob

Lift Rod

Lift Rod Extension

4020PL

Lift Rod

C

Tee connector & washer

Brass lock nut

B

A

A

PAGE 02

Page 3: 4020PL10 4020PL23 4020PL41 4020PL75P0440 P0427 P0431 P0202 Valve Body Mounting Hardware Aerator Washer Aerator Basket with Restrictor PM-510 PM-320 Aerator Housing * P0944-U 12 10

B- Align the handle lever properly with respect to the spout.

- From under the basin or counter, hand tighten the brass lock nut and fiber washer to the valve body against the counter.

C- Secure the valve body by tightening the screws attached to the lock nuts.

D- Loop and connect the flexible hoses (8) to the tee (11).

- Tighten the nuts provided at the of the hose to avoid leakage.

- Connect and tighten the Inlet hoses (9) to the supply lines. Use 1/2” IPS faucet connections, or 3/8” copper piper using compression fitting system.

3. POP-UP DRAIN INSTALLATION

A- Remove the drain flange and drain plug from pop-up assembly.

- Do not remove the gasket, washer and lock nut.

B- Apply a ring of silicone caulking underneath the drain flange.

Do not use plumbers' putty.

- Insert the threaded end of the assembly up from the under the sink. Completely thread the drain flange onto the top of the drain tube.

- Tighten the locknut from under the sink.

INSTALLATION INSTRUCTIONS

SANTEC SANTEC

Water supply line

Water supply line

SANTEC SANTEC

INLET HOSEINLET HOSE

SANTEC SANTEC

Fiber washerFiber washer

Brass lock nutBrass lock nut

B

C

D

A B

4020PL

PAGE 03

Drain Plug

Drain Flange

Lift Rod Strap

Ball Rod

Drain Tube

Ball Rod Nut

Ball Rod Clip

Thumb Screw

Lock NutWasherGasket

Side hole

Liift Rod Extension

Lift Rod & Knob

Page 4: 4020PL10 4020PL23 4020PL41 4020PL75P0440 P0427 P0431 P0202 Valve Body Mounting Hardware Aerator Washer Aerator Basket with Restrictor PM-510 PM-320 Aerator Housing * P0944-U 12 10

INSTALLATION INSTRUCTIONS

PAGE 04

C- Position the drain tube so the side hole in the pop-up faces you.

Place the drain plug into the drain tube, align its bottom hole with the side hole.

- Place the short end of the ball rod into the side hole of the drain tube and through the hole in the drain plug and tighten the ball rod nut so the ball rod moves freely. NOTE: Do not over tighten.

D- Rotate the pop-up so the ball rod faces the back wall and tighten the lock

nut giving it an extra 1/4 turn. Hand tighten the nut at the connection with P-trap. Test the rod to make sure it raises and lowers freely.

- Slip your faucet's pop-up lift rod through the holes at the top of the lift rod strap and hand tighten the thumb screw. Push the ball rod down so the drain plug is in the up position.

- Slip the one leg of the ball rod clip onto the ball rod and then slide the lift rod strap onto the ball rod using the nearest hole. Then slide the second leg of the clip onto the rod. Test the pop-up for smooth operation and adjust the strap if necessary.

4. FLUSH THE LINE

A- After all the connections have been made, remove the aerator housing (18)

basket (17) and washer (16). - Turn on the water on both hot and cold sides and flush the lines for 45 seconds.

- Turn off the water and reinsert the washer (16), basket (17) and Housing (18).

- Turn on the water and check for leakages at all joints. If water leaks from any of the connections tighten the connection until the leakage stops.

Santec Inc.3501 Challenger Street, Torrance, CA 90503Tel: (310) 542-0063 Fax (310) 542-5681 www.santecfaucet.com 08/04

SANTEC SANTEC

INLET HOSEINLET HOSE

SANTEC SANTEC

INLET HOSEINLET HOSE

TO THE COLD SUPPLY LINETO THE HOT SUPPLY LINE

C

D

ball rod

drain plug hole

lift rod strap

ball rod clip

thumb screw

4020PL

A