3M™ DSLAM Mounting Bracket Kit J0746Instructions

July 200978-8140-5663-2-A 3

78-8140-5663-2-A2

Contents

1.0 3M™ DSLAM Mounting Bracket J0746 - Installation ..................................................................3

2.0 DSLAM Installation, Nokia ..........................................................................................................5

3.0 Accessory Kit, Cable Addition Shroud J0747 for DSLAM Mounting Kit ...................................6

4.0 Cable Routing ...............................................................................................................................7

378-8140-5663-2-A

1.0 3M™ DSLAM Mounting Bracket J0746 - Installation 1.1 Unpack DSLAM Mounting Bracket.

Note: Nokia configuration shown.

1.2 DSLAM cables can be routed through the base of the cabinet below the isolation plate and/or above it through the blanking plate holes.

1.3 Cable Routing Below Isolation Plate: Using a Green-lee punch, punch two, 2" holes in center of the base as shown below. Punch two, 2" holes 11.5" above grade.

1.4 Cable Routing Above Isolation Plate: Punch two, 2" holes 11.5” and 14" from baseline as shown.

1.5 Lower DSLAM Mounting Bracket Mounting Bolts: Drill four, 7/16" holes 19-5/8" and 21-3/8" above baseline as shown.

78-8140-5663-2-A4

1.6 Remove cap bolts, lifting bracket bolt and carriage bolts plugging top mounting holes for 3M™ DSLAM Mounting Bracket.

1.7 Mount DSLAM mounting bracket on the side panel of the expanded cabinet.

1.8 Secure base with four self drilling screws through the two base cable ports and into 3M™ Cross-Connect Cabinet 4220G upright. two screws per side.

1.9 Install the top two and bottom four retaining bolts to secure the DSLAM mounting bracket to the cabinet side panel with ¼” bolt(s), lock washer(s) and flat washer(s).

578-8140-5663-2-A

2.0 3M™ DSLAM Mounting Bracket Installation, Nokia2.1 Remove adapter ring and cover plate.

2.2 Remove side and lower access panels.

2.3 Remove RDAC lifting brackets.

2.4 Clean the side of the RDAC to be mated to the expanded cabinet. Remove liner from 2.5” x 14.75” black rubber gasket. Align 3/8” holes in gasket with the two holes in the RDAC. Apply gasket. This gasket will prevent any water running down the walls between the RDAC and DSLAM mounting bracket.

2.5 Lift DSLAM onto mounting base. Using pallet anchor bolts secure DSLAM base.

2.6 Install upper mounting bolts.

2.7 Run a bead of RTV sealant along seams between cabinet and DSLAM mounting bracket and between RDAC and DSLAM mounting bracket.

78-8140-5663-2-A6

3.0 Accessory Kit, 3M™ Cable Addition Shroud J0747 for 3M™ DSLAM Mounting Bracket KitIn situations where there isn’t a free cable duct for fiber feed cable it will be necessary to install a cable addition shroud.

3.1 Remove lower and side access panels.

3.2 Place base panel and floating duct panel over cable duct.

3.3 Center floating panel around duct, secure in place with self-drilling/tapping screws.

3.4 Slide duct housing into place as shown.

3.5 Re-install side access panels with ¼” hardware.

778-8140-5663-2-A

4.0 Cable Routing

Note: Pictures are of a 3M™ Cross-Connect Cabinet 4200G2K-DSL expansion

4.1 Below Isolation Plate.

4.2 Above Isolation Plate.

3M is a trademark of 3M Company.

Important NoticeAll statements, technical information, and recommendations related to 3M’s products are based on information believed to be reliable, but the accuracy or completeness is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated with such use. Any statements related to the product which are not contained in 3M’s current publications, or any contrary statements contained on your purchase order shall have no force or effect unless expressly agreed upon, in writing, by an authorized officer of 3M.

Warranty; Limited Remedy; Limited Liability. This product will be free from defects in material and manufacture for a period of one (1) year from the time of purchase. 3M MAKES NO OTHER WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. If this product is defective within the warranty period stated above, your exclusive remedy shall be, at 3M’s option, to replace or repair the 3M product or refund the purchase price of the 3M product. Except where prohibited by law, 3M will not be liable for any indirect, special, incidental or consequential loss or damage arising from this 3M product, regardless of the legal theory asserted.

3

Communication Markets Division3M Telecommunications6801 River Place Blvd.Austin, TX 78726-90001-800-426-8688www.3MTelecommunications.com

Please Recycle. Printed in USA.© 3M 2009. All Rights Reserved.78-8140-5663-2-A