3M DBI-SALA RoofSafe Anchor and Cable System.

www.3M.com/FallProtectionForm No: 5908289 Rev: A

Always read and follow the warnings and instructions for use.

3M™ DBI-SALA®

RoofSafe Anchor and Cable System.Technical Data Sheets.

EN

Technical Data Sheet Description Page

7241279 RoofSafe Anchor Concrete Fixing 500mm x 4 42

7241182 RoofSafe Anchor Toggle Fixing 150mm x 4 43



7241172 RoofSafe Anchor Rivertherm Bearer Kit 46

7241173 RoofSafe Anchor SpeedDeck Bearer Kit 47

7241236 RoofSafe Anchor Standing Seam Bearer 48

7241175 RoofSafe Anchor Standing Seam Bearer 600mm 49

7241232 RoofSafe Anchor Tag EMEA LA 50

7241524 RoofSafe Anchor Tag EMEA EE 51

Page 3

Table of Contents

Technical Data Sheet Description Page

1425 Typical RoofSafe Cable and Anchor System 4

1201 Typical RoofSafe Trapezoidal Anchor 5

1235 Typical RoofSafe Standing Seam Anchor 6

1202 Typical RoofSafe Bitumen Anchor 7

1203 Typical RoofSafe PVC Anchor 8

1204 Typical RoofSafe All Membrane Anchor 9

7241157 RoofSafe Anchor 1P EMEA 10

7241158 RoofSafe Anchor 2P EMEA 11

7241136 RoofSafe Anchor Baseplate 405 x 405 H 12

7241137 RoofSafe Anchor Baseplate 405 x 405 BL 13



7241141 RoofSafe Anchor Module End / Corner Top Fix 16

7241142 RoofSafe Anchor Module Intermediate Top Fix 17

7241143 RoofSafe Anchor Module End / Corner Bitumen 18

7241144 RoofSafe Anchor Module Intermediate Bitumen 19

7241145 RoofSafe Anchor Module End / Corner PVC 20

7241146 RoofSafe Anchor Module Intermediate PVC 21

7241147 RoofSafe Anchor Module End / Corner All Membrane 22

7241148 RoofSafe Anchor Module Intermediate All Membrane 23

7240166 8mm Hex Swage Tensioner 0.8kN 24

7234011 Hex Swage Toggle 25

7234012 Hex Joiner 26

7240211 8mm 7x7 SS Cable 27

7234020 8mm UniGrab & Carabiner 28

7241408 90 Degree Post Mount Corner 29

7241411 45 Degree Post Mount Corner 30

7241413 Variable Intermediate Bracket 31

7241412 Intermediate Bracket 32

7241161 RoofSafe Anchor System Eye & Pin 33

7241167 RA Single Point Eye EMEA 34

7241166 RoofSafe Anchor Throw Plate Kit 35

7234005 RoofSafe 7.7 Rivet 36

7234028 RoofSafe Maxi Clamp Z 37

7234008 RoofSafe Maxi Clamp E 38

7234029 RoofSafe Maxi Clamp U 39



Issue Date: 9/8/2017 Issue No: 1 Page 4

TECHNICAL DATA SHEET: 1425Typical RoofSafe Cable and Anchor System

APPLICATION:The RoofSafe anchor and cable system is a horizontal lifeline system that allows continuous uninterrupted access to all areas of a roof.

A B C D E FG

H

I

J

Component Part Number

A RoofSafe Anchor System Eye & Pin 7241161

B 8mm Hex Swage Tensioner 0.8kN 7240166

C 8mm 7x7 SS Cable 7240211

D 8mm UniGrab & Carabiner 7234020

E Intermediate Bracket 7241412

F RoofSafe Anchor Module Intermediate Top Fix 7241142

G90 Degree Post Mount Corner 45 Degree Post Mount Corner Variable Intermediate Bracket

7241408 7241411 7241413*

H RoofSafe Anchor Module End / Corner Bitumen 7241143

I Hex Swage Toggle 7234011

J

RoofSafe Anchor Baseplate 405 x 405 H RoofSafe Anchor Baseplate 405 x 405 H RoofSafe Anchor Baseplate 405 x 405 BL RoofSafe Anchor Baseplate 350 x 440 H RoofSafe Anchor Baseplate 550 x 450 BL

7240128* 7241136 7241137* 7241138* 7241140*

*This item is different from the one illustrated


TECHNICAL DATA SHEET: 1201Typical RoofSafe Trapezoidal Anchor

APPLICATION:Select appropriate top component (A), module (B), baseplate (C) and fixings (D) to make up the correct configuration. Note: For fitting to Rivertherm and Speeddeck roof types, please refer to data sheets for the relevant support bearers. For more detailed component information refer to the individual data sheets.

A

B

C

D

15

8mm

(6.2

2”)


A

90 Degree Post Mount Corner 45 Degree Post Mount Corner Variable Intermediate Bracket Intermediate Bracket RoofSafe Anchor System Eye & Pin RoofSafe Anchor Throw Plate Kit

7241408* 7241411* 7241413* 7241412* 7241161 7241166*

B RoofSafe Anchor Module End / Corner Top Fix RoofSafe Anchor Module Intermediate Top Fix

7241141 7241142*

C

RoofSafe Anchor Baseplate 405 x 405 H RoofSafe Anchor Baseplate 405 x 405 BL RoofSafe Anchor Baseplate 350 x 440 H RoofSafe Anchor Baseplate 350 x 440 BL RoofSafe Anchor Baseplate 450 x 550 H RoofSafe Anchor Baseplate 550 x 450 BL

7241136 7241137* 7241138 7241139* 7241238* 7241140

DRoofSafe Maxi Clamp E RoofSafe Maxi Clamp U RoofSafe Maxi Clamp Z

7234008* 7234029* 7234028*


Issue Data: 9/8/2017 Issue No:3 Page 6

TECHNICAL DATA SHEET: 1235Typical RoofSafe Standing Seam Anchor

APPLICATION:Select appropriate top component (A), module (B), baseplate (C) and fixings (D) to make up the correct configuration. Note: For fitting to Rivertherm and Speeddeck roof types, please refer to data sheets for the relevant support bearers. For more detailed component information refer to the individual data sheets.

C

D

AB

158m

m (6

.22”

)


A


7241408* 7241411* 7241413* 7241412* 7241161 7241166*

B RoofSafe Anchor Module End / Corner Top Fix RoofSafe Anchor Module Intermediate Top Fix

7241141 7241142*

C

RoofSafe Anchor Baseplate 405 x 405 BL RoofSafe Anchor Baseplate 350 x 440 H RoofSafe Anchor Baseplate 350 x 440 BL RoofSafe Anchor Baseplate 550 x 450 BL

7241137* 7241138 7241139* 7241140

DRoofSafe Maxi Clamp E RoofSafe Maxi Clamp U RoofSafe Maxi Clamp Z

7234008* 7234029* 7234028*


Issue Date: 9/8/2017 Issue No:3 Page 7

TECHNICAL DATA SHEET: 1202Typical RoofSafe Bitumen Anchor

APPLICATION:Select appropriate top component (A), module (B), baseplate (C) and fixings (D) to make up the correct configuration. For more detailed component information refer to the individual data sheets.

A

B

C

D

158mm (6.22”)


A


7241408* 7241411* 7241413* 7241412* 7241161 7241166*

B RoofSafe Anchor Module End / Corner Bitumen RoofSafe Anchor Module Intermediate Bitumen

7241143 7241144*

C


7241136 7241137* 7241138 7241139* 7240128* 7241140

D

RoofSafe Anchor Toggle Fixing 150mm x 4 RoofSafe Anchor Toggle Fixing 300mm x 4 RoofSafe Anchor Concrete Fixing 500mm x 4 RoofSafe Anchor Concrete Fixing 150mm x 4 RoofSafe Anchor Concrete Fixing 300mm x 4 RoofSafe Anchor Toggle Fixing 500mm x 4

7241182 7241183* 7241279* 7241180* 7241181* 7241280*



TECHNICAL DATA SHEET: 1203 Typical RoofSafe PVC Anchor

APPLICATION:Select appropriate top component (A), module (B), baseplate (C) and fixings (D) to make up the correct configuration. For more detailed component information refer to the individual data sheets.

A

B

C

D

158mm (6.22”)


A


7241408* 7241411* 7241413* 7241412* 7241161 7241166*

B RoofSafe Anchor Module End / Corner Bitumen RoofSafe Anchor Module Intermediate Bitumen

7241143 7241144*

C


7241136 7241137* 7241138 7241139* 7240128* 7241140

D


7241182 7241183* 7241279* 7241180* 7241181* 7241280*



TECHNICAL DATA SHEET: 1204Typical RoofSafe All Membrane Anchor

APPLICATION:Select appropriate top component (A), module (B), baseplate (C) and fixings (D) to make up the correct configuration. Note: Sealing of the roof anchor should be done to the membrane manufacturers technical specification. For more detailed component information refer to the individual data sheets.

A

B

C

D

158mm (6.22”)


A


7241408* 7241411* 7241413* 7241412* 7241161 7241166*

B RoofSafe Anchor Module End / Corner All Membrane RoofSafe Anchor Module Intermediate All Membrane

7241147 7241148*

C


7241136 7241137* 7241138 7241139* 7240128* 7241140

D


7241182 7241183* 7241279* 7241180* 7241181* 7241280*



TECHNICAL DATA SHEET: 7241157RoofSafe Anchor 1P EMEAPart No: 7241157

APPLICATION: RoofSafe Anchor 1P EMEA is to be used as a single attachment point for top fix applications for one user. Note: If attachment of two users is required, please use RoofSafe Anchor 2P EMEA (7241158). Operating Temperature Range: 120°C (248°F) to -50°C (-58°F)

A

B

C

405mm (15.94”)

226m

m (8

.90”

)

PART SPECIFICATION:

Net Weight kg (lb)

Minimum Breaking Strength kN (lb)

Torque Load N/m (lb/ft)

2.48 (5.5) 22.2 (5000) 40 (29.5) COMPONENT SPECIFICATION:

Qty. Component Material Finish

A 1 RoofSafe Anchor Single Point Eye EMEA 316 Stainless Steel Polished

B 1 RoofSafe Anchor Module Int Bit Aluminum / Steel Anodized / Zinc Plated

C 1 RoofSafe Anchor Baseplate 405x405 H Aluminum Anodized


TECHNICAL DATA SHEET: 7241158RoofSafe Anchor 2P EMEAPart No: 7241158

APPLICATION:

RoofSafe Anchor 2P EMEA is to be used as a single attachment point for top fix applications for two users. Operating Temperature Range: 120°C (248°F) to -50°C (-58°F)

C

B

A

405mm (15.94”)

226m

m (8

.90”

)

PART SPECIFICATION:

Net Weight kg (lb)





A 1 RoofSafe Anchor Single Point Eye EMEA 316 Stainless Steel Polished

B 1 RoofSafe Anchor Module EC Bit Aluminum / Steel Anodized / Zinc Plated

C 1 RoofSafe Anchor Baseplate 405x405 H Aluminum Anodized


TECHNICAL DATA SHEET: 7241136RoofSafe Anchor Baseplate 405 x 405 HPart No: 7241136

APPLICATION: RoofSafe Anchor Baseplate 405 x 405 H can be used on any compatible roof type in conjunction with the appropriate RoofSafe Anchor Module, top component and fixing solution. Operating Temperature Range: 120°C (248°F) to -50°C (-58°F)

Ø27mm (1.06”)

Ø8mm (0.32”)

3mm (0.12”)200mm (7.87”)275mm (10.83”)

304mm (11.97”)

334mm (13.15”)

367mm (14.44”)

405mm (15.94”)20

0mm

(7.8

7”)

275m

m (1

0.83

”)

304m

m (1

1.97

”)

334m

m (1

3.15

”)

367m

m (1

4.44

”)

405m

m (1

5.94

”)

A

PART SPECIFICATION:

Net Weight kg (lb)



1.38 (3) 22.2 (5000) 40 (29.5) COMPONENT SPECIFICATION:


A 1 RoofSafe Anchor Baseplate 405 x 405 H Aluminum Anodized


TECHNICAL DATA SHEET: 7241137RoofSafe Anchor Baseplate 405 x 405 BLPart No: 7241137

APPLICATION: RoofSafe Anchor Baseplate 405 x 405 BL can be used on any compatible roof type in conjunction with the appropriate RoofSafe Anchor Module, top component and fixing solution. The baseplate is left blank to allow the installer to drill holes to the appropriate width. Operating Temperature Range: 120°C (248°F) to -50°C (-58°F)

3mm (0.12”)405mm (15.94”)

405m

m (1

5.94

”)

A

PART SPECIFICATION:

Net Weight kg (lb)





A 1 RoofSafe Anchor Baseplate 405 x 405 BL Aluminum Anodized



APPLICATION: RoofSafe Anchor Baseplate 350 x 440H can be used on any compatible roof type in conjunction with the appropriate RoofSafe Anchor Module, top component and fixing solution. The baseplate is left blank to allow the installer to drill holes to the appropriate width. Operating Temperature Range: 120°C (248°F) to -50°C (-58°F)

3mm (0.12”)440mm (17.30”)

350m

m (1

3.8”

)

A

PART SPECIFICATION:

Net Weight kg (lb)








APPLICATION: RoofSafe Anchor Baseplate 550x450 BL can be used on any compatible roof type in conjunction with the appropriate RoofSafe Anchor Module, top component and fixing solution. The baseplate is left blank to allow the installer to drill holes to the appropriate width. Operating Temperature Range: 120°C (248°F) to -50°C (-58°F)

3mm (0.12”)550mm (21.65”)

450m

m (1

7.72

”)

A

PART SPECIFICATION:

Net Weight kg (lb)







TECHNICAL DATA SHEET: 7241141RoofSafe Anchor Module End / Corner Top FixPart No: 7241141

APPLICATION: RoofSafe Anchor Module is to be used in conjunction with relevant baseplate and top component to create an end or corner an-chor for top fix applications. Operating Temperature Range: 120°C (248°F) to -50°C (-58°F)

C

BA

Ø99mm (3.9”)

190m

m (7

.48”

)

142m

m (5

.59”

)

D

PART SPECIFICATION:

Net Weight kg (lb)





A 1 Can Aluminum Anodized

B 1 Coil Steel Zinc Coating

C 1 Fixings A470 Stainless Steel Natural

D 1 M12 Nut & Nut Cap A470 Stainless Steel / UV Stabilized Black Polyethylene Natural/Natural


TECHNICAL DATA SHEET: 7241142RoofSafe Anchor Module Intermediate Top FixPart No: 7241142

APPLICATION: RoofSafe Anchor Module is to be used in conjunction with relevant baseplate and top component to create an intermediate an-chor for top fix applications. Operating Temperature Range: 120°C (248°F) to -50°C (-58°F)

D

A

B

C

Ø99mm (3.9”)

190m

m (7

.48”

)

142m

m (5

.59”

)

PART SPECIFICATION:

Net Weight kg (lb)





A 1 Can Aluminum Anodized

B 1 Intermediate Core Steel / Stainless Steel Zinc Coating / Natural




TECHNICAL DATA SHEET: 7241143RoofSafe Anchor Module End / Corner BitumenPart No: 7241143

APPLICATION: RoofSafe Anchor Module is to be used in conjunction with relevant baseplate and top component to create an end or corner an-chor for bitumen applications. Operating Temperature Range: 120°C (248°F) to -50°C (-58°F)

D

Ø342mm (13.46”)

185m

m (6

.22”

)

217m

m (8

.54”

)

C

A

B

PART SPECIFICATION:

Net Weight kg (lb)





A 1 Weather Shroud Aluminum Anodized





TECHNICAL DATA SHEET: 7241144RoofSafe Anchor Module Intermediate BitumenPart No: 7241144

APPLICATION: RoofSafe Anchor Module is to be used in conjunction with relevant baseplate and top component to create an end or corner an-chor for bitumen applications. Operating Temperature Range: 120°C (248°F) to -50°C (-58°F)

A

D

Ø342mm (13.46”)

158m

m (6

.22”

)

217m

m (8

.54”

)

B

C

PART SPECIFICATION:

Net Weight kg (lb)





A 1 Weather Shroud Aluminum Anodized





TECHNICAL DATA SHEET: 7241145RoofSafe Anchor Module End / Corner PVCPart No: 7241145

APPLICATION: RoofSafe Anchor Module is to be used in conjunction with relevant baseplate and top component to create an end or corner an-chor for PVC applications. Operating Temperature Range: 120°C (248°F) to -50°C (-58°F)

D

A

Ø342mm (13.46”)

158m

m (6

.22”

)

205m

m (8

.07”

)

B

C

PART SPECIFICATION:

Net Weight kg (lb)





A 1 Weather Shroud Aluminum PVC Coated





TECHNICAL DATA SHEET: 7241146RoofSafe Anchor Module Intermediate PVCPart No: 7241146

APPLICATION: RoofSafe Anchor Module is to be used in conjunction with relevant baseplate and top component to create an intermediate an-chor for PVC applications. Operating Temperature Range: 120°C (248°F) to -50°C (-58°F)

D

A

Ø342mm (13.46”)

158m

m (6

.22”

)

205m

m (8

.07”

)

B

C

PART SPECIFICATION:

Net Weight kg (lb)





A 1 Weather Shroud Aluminum PVC Coated





TECHNICAL DATA SHEET: 7241147RoofSafe Anchor Module End / Corner All MembranePart No: 7241147

APPLICATION: RoofSafe Anchor Module is to be used in conjunction with relevant baseplate and top component to create an end or corner anchor for all membrane applications. Operating Temperature Range: 120°C (248°F) to -50°C (-58°F)

D

A

Ø114mm (4.49”)14

4mm

(5.6

7”)

191m

m (7

.52”

)

B

C5.5mm (0.22”)

PART SPECIFICATION:

Net Weight kg (lb)





A 1 Can / Weather Cap Aluminum / ABS Plastic Anodized / Natural





TECHNICAL DATA SHEET: 7241148RoofSafe Anchor Module Intermediate All MembranePart No: 7241148

APPLICATION: RoofSafe Anchor Module is to be used in conjunction with relevant baseplate and top component to create an intermediate an-chor for all membrane applications. Operating Temperature Range: 120°C (248°F) to -50°C (-58°F)

D

A

Ø114mm (4.49”)14

4mm

(5.6

7”)

191m

m (7

.52”

)

B

C5.5mm (0.22”)

PART SPECIFICATION:

Net Weight kg (lb)





A 1 Can / Weather Cap Aluminum / ABS Plastic Anodized / Natural





TECHNICAL DATA SHEET: 72401668mm Hex Swage Tensioner 0.8kNPart No: 7240166

APPLICATION: The tensioner unit is attached to the anchor point using the clevis pin and split pin. It is used to set the tension of the cable in horizontal applications. Refer to installation instructions for information on assembly and installation. For use with 8mm 7x7 or 1x19 wire only. Operating Temperature Range: 120°C (248°F) to -50°C (-58°F)

AB

C

E

F

D

G

400m

m (1

5.75

”)

PART SPECIFICATION:

Net Weight kg (lb)



0.85 (1.9) 38 (8550) 60 (44.3) COMPONENT SPECIFICATION:


A 1 Clevis Pin 316 Stainless Steel Natural / Electropolished

B 1 Cotter Pin 316 Stainless Steel Natural / Electropolished

C 1 Tension Indicator Disc 316 Stainless Steel Natural / Electropolished

D 1 Lock Nut 316 Stainless Steel Natural / Electropolished

E 1 Turn Buckle 316 Stainless Steel Natural / Electropolished

F 1 Lock Nut 316 Stainless Steel Natural / Electropolished

G 1 Stud 316 Stainless Steel Natural / Electropolished


TECHNICAL DATA SHEET: 7234011 Hex Swage TogglePart No: 7234011

APPLICATION: Used to terminate cable at one end of system. For use with 8mm 7x7 or 1x19 cable only. Refer to installation instructions for information on assembly and installation. Operating Temperature Range: 120°C (248°F) to -50°C (-58°F)

109m

m (4

.29”

)

74m

m (2

.91”

)

AB

C

D

30mm (1.18”)

Ø13mm (0.66”)

28mm (1.10”)

18mm (0.71”)

13mm (0.63”) *

179m

m (7

.05”

)

PART SPECIFICATION:

Net Weight kg (lb)


0.33 (0.7) 38 (8550) COMPONENT SPECIFICATION:


A 1 Shackle 316 Stainless Steel Natural

B 1 Clevis 316 Stainless Steel Natural

C 1 Swage Terminal 316 Stainless Steel Natural

D 1 Split Pin 316 Stainless Steel Natural

* Before Swaging


TECHNICAL DATA SHEET: 7234012 Hex JoinerPart No 7234012

APPLICATION: Used to join to sections of cable together. For use with 8mm 7x7 or 1x19 wire only. Refer to installation instructions for information on assembly and installation. Operating Temperature Range: 120°C (248°F) to -50°C (-58°F)

190mm (7.48”) *200mm (7.87”)

2X 8mm (0.31”)

8mm (0.33”)

Ø13mm (0.50”)

A

78mm (3.07”) 78mm (3.07”)

PART SPECIFICATION:

Net Weight kg (lb)




A 1 Hex Swage Joiner 316 Stainless Steel Natural

* After Swaging


TECHNICAL DATA SHEET: 7240211 8mm 7x7 SS CablePart No: 7240211

APPLICATION: Used for 8m Permanent Horizontal Lifeline applications. Operating Temperature Range: 120°C (248°F) to -50°C (-58°F)

Ø8mm (0.32”)

PART SPECIFICATION:

Net Weight kg (lb)


0.242 / m (0.162 / ft) 38.7 (8700) COMPONENT SPECIFICATION:


A 1 8mm 7 x 7 Stainless Steel Cable 316 Stainless Steel Natural


TECHNICAL DATA SHEET: 72340208mm UniGrab & CarabinerPart No: 7234020

APPLICATION: For use as an attachment device for a single user in conjunction with the 8mm Permanent HLL and RoofSafe Cable systems. Note: Maximum user weight 136kg Only to be used with the carabiner provided. To prolong the life of the product, do not leave on the system when not in use. Operating Temperature Range: 120°C (248°F) to -50°C (-58°F)

A

B

60mm (2.36”)

26mm (1.02”)

Ø15mm (0.61”)

63m

m (2

.48”

)

4.- 6

mm

(.01

8 - 0

.24”

)

PART SPECIFICATION:

Net Weight kg (lb)




A 1 UniGrab 316 Stainless Steel Electropolished

B 1 Carabiner Silver Silver Zinc Passivate


TECHNICAL DATA SHEET: 7241408 90 Degree Post Mount CornerPart No: 7241408

APPLICATION: 90 degree corner bracket for post or floor mount. Used to accommodate system cable redirection at 90 degree angles. Only to be used with 7241422 11kN energy absorber or on a Roofsafe End/Corner Module. Minimum grade A4-70 M12 Fasteners should be used to fix bracket to structure at a recommended torque of 50Nm (37 ft-lbf) [40Nm (30 ft-lbf) for fitting to a Roofsafe Anchor]. Fixing shall support at least twice the load values stated in the technical report from the 3M DBI-SALA Installed Systems Calcula-tion Software for the system layout, components, number of users, and SRL or Lanyard connecting device. Tip over post mounted applications are not currently supported by the calculation software and should be designed for 22.2 kN (5000 lbf) in all directions of loading. Operating Temperature Range: 120°C (248°F) to -50°C (-58°F)

2X 3

10m

m (1

2.20

”)

2X 50mm (1.97”)

R250mm (9.84”)

2X 2

60m

m (1

0.23

”)

2X 40mm (1.57”)

100mm (3.94”)

PART SPECIFICATION:

Net Weight kg (lb)


0.6 (1.32) 22.2 (5000) COMPONENT SPECIFICATION:


A 1 90 Degree Post Mount Corner 316 Stainless Steel Natural


TECHNICAL DATA SHEET: 724141145 Degree Post Mount CornerPart No: 7241411

APPLICATION: 45 degree corner bracket for post or floor mount. Used to accommodate system cable redirection at 45 degree angles. Only to be used with 7241422 11kN energy absorber or on a Roofsafe End/Corner Module. Minimum grade A4-70 M12 Fasteners should be used to fix bracket to structure at a recommended torque of 50Nm (37 ft-lbf) [40Nm (30 ft-lbf) for fitting to a Roofsafe Anchor]. Fixing shall support at least twice the load values stated in the technical report from the 3M DBI-SALA Installed Systems Calcula-tion Software for the system layout, components, number of users, and SRL or Lanyard connecting device. Tip over post mounted applications are not currently supported by the calculation software and should be designed for 22.2 kN (5000 lbf) in all directions of loading. Cable Tensioning: 0.8 kN Operating Temperature Range: 120°C (248°F) to -50°C (-58°F)

A

23mm (0.92”)

70mm (2.76”)

2X 1

00m

m (3

.94”

)

215m

m (8

.46”

)

350m

m (1

3.78

”)Ø13mm (0.51”)

R250mm (9.84”)

200mm (7.87”)

PART SPECIFICATION:

Net Weight kg (lb)


0.5 (1.1) 22.2 (5000) COMPONENT SPECIFICATION:


A 1 45 Degree Post Mount Corner 316 Stainless Steel Natural


TECHNICAL DATA SHEET: 7241413Variable Intermediate BracketPart No: 7241413

APPLICATION: Used to accommodate system cable redirection at small angles. Field formable at time of installation. Post, floor or wall mounting. Minimum grade A4-70 M12 Fasteners should be used to fix bracket to structure at a recom-mended torque of 50Nm (37 ft-lbf) [40Nm (30 ft-lbf) for fitting to a Roofsafe Anchor]. Fixing shall support at least twice the load values stated in the technical report from the 3M DBI-SALA Installed Systems Calculation Software for the system layout, components, number of users, and SRL or Lanyard connecting device. Tip over post mounted applications are not currently supported by the calculation software and should be designed for 22.2 kN (5000 lbf) in all directions of loading. Cable Tensioning: 0.8 kN Operating Temperature Range: 120°C (248°F) to -50°C (-58°F)

250mm (9.84”)

A

70m

m (2

.76)

Ø13mm (0.51”)

S-1

66mm (2.59”)

44m

m (1

.73”

)

Ø13mm (0.51”)

S-2

55m

m (2

.17)

PART SPECIFICATION:

Net Weight kg (lb)

Breaking Strength kN (lb)

(S-1) Cable Exit Angle

(S-2) Formation Angle

0.3 (0.7) 24 (5400) 15° Maximum 15° Maximum COMPONENT SPECIFICATION:


A 1 Variable Intermediate Bracket 316 Stainless Steel Natural


TECHNICAL DATA SHEET: 7241412Intermediate BracketPart No: 7241412

APPLICATION: Standard intermediate bracket for post, floor, or wall mount. Minimum grade A4-70 M12 Fasteners should be used to fix bracket to structure at a recommended torque of 50Nm (37 ft-lbf) [40Nm (30 ft-lbf) for fitting to a Roofsafe Anchor]. Fixing shall support at least twice the load values stated in the technical report from the 3M DBI-SALA Installed Systems Calculation Software for the system layout, components, number of users, and SRL or Lanyard connecting device. Tip over post mounted applications are not currently supported by the calculation software and should be designed for 22.2 kN (5000 lbf) in all directions of loading. Cable Tensioning: 0.8 kN or 5.0 kN Operating Temperature Range: 120°C (248°F) to -50°C (-58°F)

Ø13mm (0.51”)

Ø12mm (0.47”)Ø9mm (0.35”)

68m

m (2

.70”

)

100mm (3.94”)

60mm (2.36”)

44m

m (1

.73”

)

A

S-1

PART SPECIFICATION:

Net Weight kg (lb)


(S-1) Cable Exit Angle

0.2 (0.4) 24 (5400) 15° Maximum (0° for 5kN Tension) COMPONENT SPECIFICATION:


A 1 Intermediate Bracket 316 Stainless Steel Natural


TECHNICAL DATA SHEET: 7241161RoofSafe Anchor System Eye & PinPart No: 7241161

APPLICATION: To be fitted to an End Anchor in an 8mm RoofSafe Cable System. M12 A470 SS Bolt, Nyloc Nut & Washer as supplied with post. Operating Temperature Range: 120°C (248°F) to -50°C (-58°F) Note: To be used ONLY on End/Corner Anchors. Do not fit to Intermediate Anchors.

A

B

C

59mm (2.31”)

Ø13mm (0.51”)

80m

m (3

.15”

)

67m

m (2

.64”

)

30mm (1.16”)

PART SPECIFICATION:

Net Weight kg (lb)





A 1 RoofSafe Anchor System Eye 316 Stainless Steel Electropolished

B 1 RoofSafe Anchor System Eye Pin 316 Stainless Steel Electropolished

C 1 Split Pin 316 Stainless Steel Electropolished


TECHNICAL DATA SHEET: 7241167RA Single Point Eye EMEAPart No: 7241167

APPLICATION: Used in conjunction with RoofSafe Anchors to create a single point attachment for 1 or 2 users. Operating Temperature Range: 120°C (248°F) to -50°C (-58°F)

A

B

C69mm (2.72”)

57.4

mm

(2.2

6”)

Ø50mm (1.97”)

Ø30mm (1.18”)

Ø12mm (0.48”)

PART SPECIFICATION:

Net Weight kg (lb)



0.34 (0.7) 26 (5850) 40 (29.5) COMPONENT SPECIFICATION:


A 1 RA Single Point Eye EMEA 316 Stainless Steel Polished

B 1 M12 Washer 316 Stainless Steel Polished

C 1 RA Rotation Sleeve 316 Stainless Steel Polished


TECHNICAL DATA SHEET: 7241166RoofSafe Anchor Throw Plate KitPart No: 7241166

APPLICATION: For use with a RoofSafe End / Corner Anchor to allow two systems to intersect on the same post. Note: Additional fasteners are provided to attach the plate. RoofSafe™ Anchor sold separately. Cannot be used with old style Force Management Anchors. Operating Temperature Range: 120°C (248°F) to -50°C (-58°F)

A

BC

D

140mm (5.51”)

Ø13mm (0.49”)

50m

m (1

.97”

)

PART SPECIFICATION:

Net Weight kg (lb)




A 1 M12x25 Set Screw A470 Stainless Steel Natural

B 1 M12 Flat Washer A470 Stainless Steel Natural

C 1 RoofSafe Anchor Throw Plate 316 Stainless Steel Electropolished

D 1 M12 Nylon Insert Lock Nut A470 Stainless Steel Natural


TECHNICAL DATA SHEET: 7234005RoofSafe 7.7 RivetPart No: 7234005

APPLICATION: Used in conjunction with RoofSafe Anchors and RoofSafe Rail for installation on trapezoidal roof profiles (composite/built up/se-cret fix) and for joining RoofSafe Rail to spreader plates. Fixing in application shall be designed to withstand a minimum of 5kN in shear and tension at each corner of the RoofSafe base-plate Single Rivet - Shear Strength = 6.8kN / Tensile Strength = 5kN / Grip Range = 1 to 9.5mm

C

DA

B

A Baseplate

B Sealing Tape

PART SPECIFICATION:

Net Weight kg (lb)

0.67 / 100 (1.48 / 100) COMPONENT SPECIFICATION:


C 1 Rivet 6000 Series Aluminum Alloy Natural

D 1 Washer A470 Stainless Steel Natural


TECHNICAL DATA SHEET: 7234028RoofSafe Maxi Clamp ZPart No: 7234028

APPLICATION: Used to attach RoofSafe Anchors and RoofSafe™ Rail to bulb type standing seam roof profiles. Fixing in application shall be designed to withstand a minimum of 5kN in shear and tension at each corner of the RoofSafe base-plate Operating Temperature Range: 120°C (248°F) to -50°C (-58°F)

A

C

B

EF

D

45mm (1.77”)

51m

m (2

.01”

)Ø23mm (0.91)

PART SPECIFICATION:

Net Weight kg (lb)


0.26 (0.6) 30 (22.1) COMPONENT SPECIFICATION:


A 1 Body 6000 Series Aluminum Alloy Natural

B 1 Insert 6000 Series Aluminum Alloy Natural

C 1 M10 x 20 Fastener A470 Stainless Steel Natural

D 1 3/8” x 1/2” Set Screw A470 Stainless Steel Natural

E 1 M10 Spring Washer A470 Stainless Steel Natural

F 1 M10 Flat Washer A470 Stainless Steel Natural


TECHNICAL DATA SHEET: 7234008RoofSafe Maxi Clamp EPart No: 7234008

APPLICATION: Used to attach the RoofSafe Rail and RoofSafe Anchors to a variety of standing seam roof profiles. Fixing in application shall be designed to withstand a minimum of 5kN in shear and tension at each corner of the RoofSafe base-plate Operating Temperature Range: 120°C (248°F) to -50°C (-58°F)

A

B

CD

E

7mm (0.27”)

25mm (0.98”)

50m

m (1

.97”

)

30m

m (1

.18”

)

8.9mm (0.35”)

PART SPECIFICATION:

Net Weight kg (lb)





B 1 M10 x 20 Fastener A470 Stainless Steel Natural

C 1 3/8” x 1/2” Set Screw A470 Stainless Steel Natural

D 1 M10 Spring Washer A470 Stainless Steel Natural

E 1 M10 Flat Washer A470 Stainless Steel Natural


TECHNICAL DATA SHEET: 7234029RoofSafe Maxi Clamp UPart No: 7234029

APPLICATION: Used to attach the RoofSafe Rail and RoofSafe Anchors to a variety of standing seam roof profiles. Fixing in application shall be designed to withstand a minimum of 5kN in shear and tension at each corner of the RoofSafe base-plate Operating Temperature Range: 120°C (248°F) to -50°C (-58°F)

A

B

CD

E

38mm (1.50”)

10mm (0.39”)

50m

m (1

.97”

)

38m

m (1

.50”

)

14mm (0.55”)

PART SPECIFICATION:

Net Weight kg (lb)





B 1 3/8” x 1/2” Set Screw A470 Stainless Steel Natural

C 1 M10x20 Fastener A470 Stainless Steel Natural

D 1 M10 Flat Washer A470 Stainless Steel Natural

E 1 M10 Spring Washer A470 Stainless Steel Natural


TECHNICAL DATA SHEET: 7241180RoofSafe Anchor Concrete Fixing 150mm x 4Part No: 7241180

APPLICATION: Used in conjunction with RoofSafe Anchors and RoofSafe™ Rail for installation into concrete. Note: suitable for solid (min strength of 25N/mm²) or hollow (min strength of 55N/mm²) concrete. Fixing in application shall be designed to withstand a minimum of 5kN in shear and tension at each corner of the RoofSafe base-plate. Operating Temperature Range: 120°C (248°F) to -50°C (-58°F)

B

E

C

A

BA

C

D

F H

I

150m

m (5

.91”

)

K

G J L

A New Membrane

B Old Membrane

C Insulation

D Concrete with Insulation

E Hollow Core Concrete with Insulation

PART SPECIFICATION:

Net Weight kg (lb)




F 1 Foam Insulation Polyethylene Foam Natural

G 1 Cup Washer Carbon Steel Zinc Flake

H 1 Alignment Tube PVC Natural

I 1 M8 Concrete Fixing Carbon Steel Zinc Plating

J 1 M8 Washer Carbon Steel Zinc Flake

K 1 M8 Threaded Rod Grade 8.8 Steel Zinc Plating

L 1 M8 Nut Grade 8.8 Steel Zinc Plating


TECHNICAL DATA SHEET: 7241181RoofSafe Anchor Concrete Fixing 300mm x 4Part No: 7241181

APPLICATION: Used in conjunction with RoofSafe Anchors and RoofSafe Rail for installation into concrete. Note: suitable for solid (min strength of 25N/mm²) or hollow (min strength of 55N/mm²) concrete. Fixing in application shall be designed to withstand a minimum of 5kN in shear and tension at each corner of the RoofSafe base-plate. Operating Temperature Range: 120°C (248°F) to -50°C (-58°F)

B

E

C

A

BA

C

D

300m

m (1

1.81

”)

F H

I

K

G J L

A New Membrane

B Existing Membrane

C Insulation



PART SPECIFICATION:

Net Weight kg (lb)










L 1 M8 Nut Grade 8.8 Steel Zinc Plating


TECHNICAL DATA SHEET: 7241279 RoofSafe Anchor Concrete Fixing 500mm x 4Part No: 7241279

APPLICATION: Used in conjunction with RoofSafe Anchors and RoofSafe Rail for installation into concrete. Note: suitable for solid (min strength of 25N/mm²) or hollow (min strength of 55N/mm²) concrete. Fixing in application shall be designed to withstand a minimum of 5kN in shear and tension at each corner of the RoofSafe base-plate. Operating Temperature Range: 120°C (248°F) to -50°C (-58°F)

B

E

C

A

BA

C

D

500m

m (1

9.69

”)

F H

I

K

G J L

A New Membrane

B Existing Membrane

C Insulation



PART SPECIFICATION:

Net Weight kg (lb)











TECHNICAL DATA SHEET: 7241182RoofSafe Anchor Toggle Fixing 150mm x 4Part No: 7241182

APPLICATION: Used in conjunction with RoofSafe Anchors for installation on flat roofs on trapezoidal and plywood deck (Min 18mm (0.71”) thick). Fixing in application shall be designed to withstand a minimum of 5kN in shear and tension at each corner of the RoofSafe base-plate. Operating Temperature Range: 120°C (248°F) to -50°C (-58°F)

A

B

C

D

150m

m (5

.91”

)

E GI

K L

F H J

A New Membrane

B Existing Membrane

C Insulation

D Deck

PART SPECIFICATION:

Net Weight kg (lb)




E 1 Foam Insulation Polyethylene Foam Natural

F 1 Cup Washer Carbon Steel Zinc Flake

G 1 Alignment Tube PVC Natural

H 1 M8 Washer Carbon Steel Zinc Flake

I 1 M8 Bolt Grade 8.8 Steel Zinc Plating

J 1 M8 Nut Grade 8.8 Steel Zinc Plating

K 1 M8 Barrel Nut Carbon Steel Zinc Plating

L 1 Toggle Forming Carbon Steel Zinc Plating


TECHNICAL DATA SHEET: 7241183 RoofSafe Anchor Toggle Fixing 300mm x 4Part No: 7241183


A

B

C

D

300m

m (1

1.81

”)

E GI

K L

F H J

A New Membrane

B Existing Membrane

C Insulation

D Deck

PART SPECIFICATION:

Net Weight kg (lb)








I 1 M8 Bolt Grade 8.8 Steel Zinc Plating





TECHNICAL DATA SHEET: 7241280RoofSafe Anchor Toggle Fixing 500mm x 4Part No: 7241280


A

B

C

D

500m

m (1

9.69

”)

E GI

K L

F H J

A New Membrane

B Existing Membrane

C Insulation

D Deck

PART SPECIFICATION:

Net Weight kg (lb)








I 1 M8 Threaded Rod Grade 8.8 Steel Zinc Plating





TECHNICAL DATA SHEET: 7241172RoofSafe Anchor Rivertherm Bearer KitPart No: 7241172

APPLICATION: Used to attach RoofSafe Anchors to CA Rivertherm roof profiles. Note: RoofSafe™ Anchor sold separately. Pack contains 2 bearers, suitable for a one anchor. Operating Temperature Range: 120°C (248°F) to -50°C (-58°F)

B

AC

600m

m (2

3.62

”)

A Bulb Tite Rivets (5.2 x 19.1)

B Butyl Tape (Class A)

PART SPECIFICATION:

Net Weight kg (lb)




C 1 CA Rivertherm RT 500 5000 Series Aluminum Alloy Powder Coated


TECHNICAL DATA SHEET: 7241173RoofSafe Anchor SpeedDeck Bearer KitPart No: 7241173

APPLICATION: Used in conjunction with RoofSafe Anchors for installation on SpeedDeck roof profiles. Note: RoofSafe Anchor Module and Baseplate sold separately. For use on roof sheets from: Steel 0.42mm / Aluminum 0.7mm. Pack contains 2 bearers, suitable for a one anchor. Operating Temperature Range: 120°C (248°F) to -50°C (-58°F)

A

B C

D

350m

m (1

3.78

”)30

0mm

(11.

81”)

A RoofSafe Anchor Module EC Top Fix (7241141)*

B M8 x 20 A470 Bolt

C RoofSafe Anchor Baseplate 305x440 H (7241138)*

* Order Separately

PART SPECIFICATION:

Net Weight kg (lb)




D 1 Bulb Tite Rivet 5.2 x 19.1 6000 Series Aluminum Alloy Powder Coated


TECHNICAL DATA SHEET: 7241236RoofSafe Anchor Standing Seam BearerPart No: 7241236

APPLICATION: Used in conjunction with RoofSafe Anchors for installation on standing seam roof profiles with a seam width of greater than 500mm. (Seam width to be specified at the time of order.) Pack contains 2 bearers, suitable for one anchor. Note: RoofSafe™ Anchor and Clamps sold separately. Operating Temperature Range: 120°C (248°F) to -50°C (-58°F)

A

BC

D

1050

mm

(41.

34”)

1000

mm

(39.

37”)

51mm (2.0”)

E


B RoofSafe 7.7 Rivet 100 (7234005)* RoofSafe 7.7 Rivet 500 (7234006)*


D Clamp*

* Order Separately

PART SPECIFICATION:

Net Weight kg (lb)

1.46 (3.2) COMPONENT SPECIFICATION:


E 1 RoofSafe Anchor Standing Seam Bearer 6000 Series Aluminum Alloy Powder Coated


TECHNICAL DATA SHEET: 7241175RoofSafe Anchor Standing Seam Bearer 600mmPart No: 7241175

APPLICATION: Used in conjunction with RoofSafe Anchors for installation on standing seam roof profiles with a seam width of greater than 500mm. (Seam width to be specified at the time of order.) Pack contains 2 bearers, suitable for one anchor. Note: RoofSafe Anchor and Clamps sold separately. Operating Temperature Range: 120°C (248°F) to -50°C (-58°F)

A

BC

D

650m

m (2

5.6”

)

600m

m (2

3.6”

)

51mm (2.0”)


B RoofSafe 7.7 Rivet 100 (7234005)* RoofSafe 7.7 Rivet 500 (7234006)*


D Clamp*

* Order Separately

PART SPECIFICATION:

Net Weight kg (lb)



E 1 RoofSafe Anchor Standing Seam Bearer 600mm 6000 Series Aluminum Alloy Natural


TECHNICAL DATA SHEET: 7241232RoofSafe Anchor Tag EMEA LAPart No: 7241232

APPLICATION: For use on all cable systems (Languages: English, Spanish, Dutch, German, French, Portuguese, Italian and Swedish). Must be attached in a visible location near the start of the system. It is completed by the installer with essential information for the user. Operating Temperature Range: 120°C (248°F) to -50°C (-58°F)

215mm (8.45”)

90m

m (3

.54”

)

PART SPECIFICATION:

Net Weight kg (lb)



A 1 Anchor Tag EMEA LA Aluminum 5005 Anodized. Screen printed & low temperature baked.


TECHNICAL DATA SHEET: 7241524 RoofSafe Anchor Tag EMEA EEPart No: 7241524

APPLICATION: For use on all cable systems (Languages: English Turkish, Polish, Hungarian, Romanian, Slovak, and Russian.). Must be attached in a visible location near the start of the system. It is completed by the installer with essential information for the user. Operating Temperature Range: 120°C (248°F) to -50°C (-58°F)

215mm (8.45”)

90m

m (3

.54”

)

Горизонтальная гибкая анкерная линия RoofSafe

PART SPECIFICATION:

Net Weight kg (lb)



A 1 Anchor Tag EMEA EE Aluminum 5005 Anodized. Screen printed & low temperature baked.

I S O9 0 0 1

USA3833 SALA Way Red Wing, MN 55066-5005 Toll Free: 800.328.6146Phone: 651.388.8282Fax: [email protected]

BrazilRua Anne Frank, 2621Boqueirão Curitiba PR81650-020BrazilPhone: [email protected]

MexicoCalle Norte 35, 895-ECol. Industrial VallejoC.P. 02300 AzcapotzalcoMexico D.F.Phone: (55) [email protected]

ColombiaCompañía Latinoamericana de Seguridad S.A.S.Carrera 106 #15-25 Interior 105 Manzana 15Zona Franca - Bogotá, ColombiaPhone: 57 1 [email protected]

Canada260 Export Boulevard Mississauga, ON L5S 1Y9 Phone: 905.795.9333 Toll-Free: 800.387.7484 Fax: 888.387.7484 [email protected]

EMEA (Europe, Middle East, Africa)EMEA Headquarters:5a Merse RoadNorth Moons MoatRedditch, WorcestershireB98 9HL UKPhone: + 44 (0)1527 548 000Fax: + 44 (0)1527 591 [email protected]

France:Le Broc CenterZ.I. 1re Avenue - BP1506511 Carros Le Broc CedexFrancePhone: + 33 04 97 10 00 10Fax: + 33 04 93 08 79 [email protected]

Australia & New Zealand95 Derby StreetSilverwaterSydney NSW 2128AustraliaPhone: +(61) 2 8753 7600Toll-Free : 1800 245 002 (AUS)Toll-Free : 0800 212 505 (NZ) Fax: +(61) 2 8753 7603 [email protected]

AsiaSingapore:1 Yishun Avenue 7Singapore 408731Phone: +65 - 65587758Fax: +65 - [email protected]

Shanghai:19/F, L’Avenue, No.99 Xian Xia RdShanghai 200051, P R China Phone: +86 21 62539050Fax: +86 21 [email protected]

3M.com/FallProtection

3M DBI-SALA RoofSafe Anchor and Cable System.

Documents

Transcript of 3M DBI-SALA RoofSafe Anchor and Cable System.