3600 SERIES 3600 Series Heavy Duty Pumps · PDF fileCOmPLeTe PaCKaGeD PumP sOLuTIONs 1300...

COMPLETE PACKAGED PUMP SOLUTIONS 1300 ALLPUMPS (255 786) www.allpumps.com.au

33GE

AR p

umps

Gear PumPs 3600 SERIES

3600 Series Heavy Duty PumpsGeneral Purpose Pumps for Mixing, Blending, Recirculating, Fixed and Mobile Transfer

Up to 468 GPM • Up to 125 PSIThese pumps operate smoothly and with equal efficiency in either direction of rotation. They effectively handle heavy, viscous materials such as asphalt, molasses, roofing compounds, and printing inks, as well as fuel oils, gasolines, and similar thin liquids.

Pumps can be supplied in several materials of construction, with or without built-in relief valves. Pumps can be assembled either hi-drive or low-drive, and are available with conventional packed box or lapped-face mechanical shaft seal. They can be direct driven or driven through a built-in gear reduction with a wide range of ratios. These pumps operate equally well regardless of the mounting configuration or the direction of rotation.

FeaturesQuiet-Running Helical Gears• Heat treated cast-iron pumping gears are accurately

machined for quiet, efficient operation and long life.

• The pumping gears are keyed to their shafts with a sliding fit and are easily replaced.

• Accurate machining insures proper meshing, and reduces friction and vibration.

Long-Lasting Bearing Surfaces• Bearings are special wear-resistant, high-lead

bronze. Iron and carbon bearings are available.

• Four heavy duty sleeve bearings give positive support to pumping gears and insure long, efficient service.

• Bearing grooves allow circulation of the liquid being pumped for lubrication & control of bearing temperature.

• Outboard drive shaft bearing supports external radial loads and absorbs thrust loads.

Precision-Ground Shafts• The steel shafts are induction hardened in the

bearing and sealing areas and are precision ground to exacting standards for maximum life.

• Hardened stainless steel shafts available.

Rugged Housing• Standard castings are cast iron.

• Precise manufacturing tolerances provide minimum clearances for maximum pumping efficiency.

• Large, hardened steel dowel pins insure positive alignment between the faceplate, case, and backplate.


34Gear PumPs

3600 SERIES

MODELTHEORETICAL CAPACITY

MAXIMUM SPEEDMAXIMUM FLOw AT MAXIMUM SPEED (0 DISCHARGE PRESSURE)

MAXIMUM PRESSURE

PORT CONNECTION

3611/3711 416.4 CC/REV 750 RPM 18.6 M3/HR 8.6 Bar 2" BSP












STANDARD OPTION

Housing Cast Iron

Shafts Steel Stainless Steel

Gears Hardened Iron Stainless Steel

Bearings BronzeCarbonIronGlass/PTFE

Packing Graphite Filament Teflon

Mechanical Seal Carbon/Stainless (Nitrile Elastomers)

Viton ElastomersTeflon Elastomers

Performance

Materials of Construction

N.B.: Not all combinations are available on all pump models.


35GE

AR p

umps


Model Number Designation3(i)

6(ii)

17(iii)

HBFRV(iv)

8851(v)

(i) Port Orientation 3 – 3600 Series with right angle ports

(ii) Shaft Sealing 6 – Packing 7 – Mechanical Seal

(iii) Flowrate in US Gallons/100 Revolutions 11 = 0.416 L/Rev (0.11 gpr) 17 = 0.644 L/Rev (0.17 gpr) 22 = 0.833 L/Rev (0.22 gpr) 32 = 1.211 L/Rev (0.32 gpr) 35 = 1.32 L/Rev (0.35 gpr) 43 = 1.63 L/Rev (0.43 gpr) 48 = 1.82 L/Rev (0.48 gpr) 58 = 2.20 L/Rev (0.58 gpr)

(iv) Pump Head Arrangement H – Pump without outboard bearing HB – Pump with outboard bearing F – Pump with flanged connections (bolt on threaded flange) RV – Pump with integral pressure relief valve

(v) Specialty Code 8851 = BSP(F) Connections


36Gear PumPs

3600 SERIES

Key Components

BEARINGSFour heavy duty sleeve bearings give positive support to pumping gears and ensure long, efficient service. A special wear-resistant, high-lead bronze bearing is standard on 3600 Series Pumps. For thin non-abrasive liquids we offer optional carbon bearings, as well as iron bearings for abrasive liquids. The bearings are grooved to allow circulation of the liquid being pumped for lubrication & control of bearing temperature

GEARSThe helical pumping gears are machined from heat treated cast iron because of its excellent wear resistance.

For chemical pumping applications, the standard gears can be replaced with stainless steel or bronze. An optional Delrin® idler gear can be used for quieter operation when running thin liquids.

SHAFTSStandard steel shafts are induction hardened in the bearing and sealing areas, and are precision ground to exacting standards for maximum life. Hardened stainless steel shafts are also available upon request.

HOUSINGOur rugged cast-iron housings are manufactured to precise tolerances, providing minimum clearances for maximum pumping efficiency. Large, hardened steel dowel pins ensure positive alignment between the faceplate, case, and backplate.

GASKETS3600 Series Pumps come standard with fiber gaskets that are used up to 212oF/100oC. For higher temperature applications (up to 450oF/232oC) we offer other optional gasket materials.


37GE

AR p

umps


Relief Valves & JacketingRELIEF VALVEIn the event of overpressure situations, our adjustable relief valve protects personnel and equipment by returning liquids to the suction side of the pump. Various spring sizes can be specified to handle a wide range of operating conditions.

Roper Pump’s inverted poppet relief valve is designed without close fitting guides that can clog and cause excessive pressures when the valve does not open freely. The valve will provide protection in only one direction of rotation. However it can be positioned easily to either side of the pump to accommodate flow direction.

BI-DIRECTIONAL RELIEF VALVE*Roper Pump’s integral bi-directional pressure relief valve offers reliable protection of your personnel and equipment, regardless of which direction you are pumping. You can reverse flow without disabling pressure relief operability, or compromising operator safety. Based on our rugged and time proven standard relief valves, this offers you a lighter weight, lower cost alternative compared to externally plumbed systems.

JACKETING**Whether the fluid to be pumped must be heated, cooled, or maintained at a specific temperature, a jacketed Roper pump will handle difficult-to-pump materials such as Bunker C, molasses, asphalt mixes, refined sugars, creosote, printing ink, and other viscous fluids which require temperature control for satisfactory handling.

Roper Pump jacketed pumps provide efficient heat transfer to the packing, seal relief valve, bearing areas, and endplates of the pump. The jackets are suitable for use with steam, hot or cold water, heat transfer oil, etc., as heating or cooling mediums.

Jacketing is available on the faceplate only, backplate only, or on both.

*Available on 11, 17 and 22 sizes

**Jacketing is not available on 32, 43 and 48 sizes


38Gear PumPs

3600 SERIES

Pump Seals

MECHANICAL SEALMechanical seals are for those applications where product leakage is unacceptable. Under proper conditions the mechanical seal has a longer service life than the packed box and does not require adjustment. The standard mechanical seal is an elastomeric bellows type seal. A PTFE wedge seal is also available.

PACKED BOXOur standard packing is suited for general purpose applications, and is easily replaced with split ring packing. For optimum performance, the gland should be adjusted to allow slight seepage. Standard packing is graphite, with several optional packing materials available for applications involving high temperatures or mildly corrosive liquids, or those requiring compatibility with food products.

TRIPLE LIP SEALOffering the same high degree of sealing reliability as a mechanical seal, triple lip seals are better suited for viscous products that tend to set up while the pump is idle, such as resins, glues and paints. The lips create an effective barrier to product leakage, and will move freely upon resumption of pumping a thickening substance. In cases where extreme circumstances can cause catastrophic failure of mechanical seals, the resilient nature of the triple lip seal makes it relatively immune to sudden failure.


39GE

AR p

umps


H &

HB

B

HG

BH

& H

GH

B

F

F

F

F

G

G

O

O

V

V

P

P

PORT

PORT

KEY

PORT

PORT

PORT

PORT

F

F

F

F H

H

HG

H

O

O

P

P

P

P

PORT

PORT

R

E

E

E

E

R

R

R

E

E

E

E

NU

C

C

C

C

N

U

D

NM

NM

NM

NM

W

W

N

N

X

X

U

U D

D

D

K

K

K

K

Dimensions90° Ports


40Gear PumPs

3600 SERIES

IN[MM]

3600 SERIES CD

E F GH

HOLE DIAMETER

K N NM O P R U V w X KEY PORTSHIGH

NO

OU

TBO

ARD

BEA

RIN

G

11

H & HRV (SPEC G) 15.97

[405]

6.44[163]

0.88[22]

2.75[69]

0.75[19]

0.56[14]

5[127]

2.58[65]

10.34[262]

10.75[273]

3.62[91] 19.57

[497]

1.06[26.9]

4[101]

N/A N/A

.25 SQ. x 1.50

2 NPT TAPPED

HF&HFRV (SPECG)

11.54[293]

4.3[109]

2 NPT FLANGE

17

H & HRV (SPEC G) 16.72

[424]1.83[46]

10.75[273]

3.62[91] 20.33

[516]

2 NPT TAPPED

HF&HFRV (SPECG)

11.54[293]

4.3[109]

2 NPT FLANGE

22 HF&HFRV (SPECG)

18.59[472]

2.2[55]

11.46[291]

12.16[308]

6.41[162]

22.19[563]

4.41[112]

3 NPT FLANGE

35

H&HRV19.53[496] 9.25

[234]5.19[131]

1.5[38]

0.69[17]

9.25[234]

2.15[54]

11.96[303]

15.63[397]

6.88[175] 23.04

[585] 1.437[36.5]

6[152]

.38 SQ. x 1.62

3 NPT TAPPED

HF & HFRV

16.66[423]

7.91[200]

3 NPT FLANGE

58 HF&HFRV (SPECG)

22.51[571]

2.29[58]

13.52[343]

17.35[441]

8.1[205]

26.02[660]

6.28[159]

4 NPT FLANGE

NO

OU

TBO

ARD

BEA

RIN

G

11

HB & HBRV 19.32

[490]

6.44[163]

0.88[22]

2.75[69]

0.75[19]

0.56[14]

5[127]

3.45[87]

13.69[347]

10.75[273]

3.62[91] 22.92

[582]

1[25.4]

4[101]

N/A N/A

.25 SQ. x 1.50

2 NPT TAPPED

HBF & HBFRV

0.62[15]

11.54[293]

4.3[109]

2 NPT FLANGE

17

HB & HBRV 20.07

[509] 0.75[19]

2.7[68]

10.75[273]

3.62[91] 23.67

[601]

2 NPT TAPPED

HBF & HBFRV

11.54[293]

4.3[109]

2 NPT FLANGE

22 HBF & HBFRV

21.57[547]

14.4[366]

12.16[308]

6.41[162]

25.17[639]

4.41[112]

3 NPT FLANGE

35

HB & HBRV 23.69

[601] 9.25[234]

5.19[131]

1.5[38]

0.69[17]

9.25[234]

3.25[82]

16.12[409]

15.63[397]

6.88[174] 27.2

[690] 1.25[31.75]

6[152]

3 NPT TAPPED

HBF & HBFRV

16.66[423]

7.91[200]

3 NPT FLANGE

58 HBF & HBFRV

26.53[673]

17.54[445]

17.35[440]

8.1[205]

30.04[763]

6.28[159] .38 SQ. x 2.25 4 NPT

FLANGE

NO

OU

TBO

ARD

BEA

RIN

G

11

GHB & GHBRV 20.47

[519]

6.44[163]

0.88[22]

2.75[69]

0.75[19]

0.56[14]

5[127]

1.74[44]

14.83[376]

10.75[273]

3.62[91] 24.07

[611]

1[25.4]

4[101] 3.523

[89]10.24[260] .25 SQ. x 1.50

2 NPT TAPPED

GHBF & GHBFRV

0.62[15]

11.54[293]

4.3[109]

2 NPT FLANGE

17

GHB & GHBRV 21.97

[558] 0.75[19]

15.58[395]

10.75[273]

3.62[91] 25.57

[649]

2 NPT TAPPED

GHBF & GHBFRV

11.54[293]

4.3[109]

2 NPT FLANGE

22 GHBF & GHBFRV

23.47[596]

16.33[414]

12.16[308]

6.41[162]

27.07[687]

4.41[112]

3 NPT FLANGE

35

GHB & GHBRV 25.88

[657] 9.25[234]

5.19[131]

1.5[38]

0.69[17]

9.25[234]

2.29[58]

18.31[465]

15.63[397]

6.88[174] 29.39

[746] 1.125[28.58]

6[152] 4.189

[106]11.25[285]

.25 SQ. x 1.50

3 NPT TAPPED

GHBF & GHBFRV

16.66[423]

7.91[200]

3 NPT FLANGE

58 GHBF & GHBFRV

28.72[729]

19.73[501]

17.35[440]

8.1[205]

32.23[818]

6.28[159] .25 SQ. x 1.50 4 NPT

FLANGE


41GE

AR p

umps

3.25[82]

11.50[292]

3.15[80]

2.65[67]

1.91[48]

3.00[76]

3.00[76]

2.29[58]

R

C

NM

.25 SQ X 1.5 KEY

1.125 [28.58]

6.84 [173]

6.09 [157] 5.10 [129]

PORT

4.19 [106]

1.75 [44]

0.625[15]

11.25 [285]

3.25[82]

11.50[292]

3.15[80]

2.65[67]

1.91[48]

3.94[100]

3.00[76]

3.00[76]

1116

6.40 [162]HI-DRIVE

3.75 [95]LO-DRIVE

1.25 [31.75]

0.625 [15]

R

C

NM

.25 SQ X 2.25 KEY

FOUR HOLES

6.84 [173]

6.09 [157] 5.10 [129]

HI-DRIVE

LO-DRIVE

PORT

6.40[163]

3.75[95] VARIABLE

3.25[82]

11.50[292]

3.15[80]

2.65[67]

1.91[48]

3.00[76]

3.00[76]

2.29[58]

R

C

NM

.25 SQ X 1.5 KEY

1.125 [28.58]

6.84 [173]

6.09 [157] 5.10 [129]

PORT

4.19 [106]

1.75 [44]

0.625[15]

11.25 [285]

3.25[82]

11.50[292]

3.15[80]

2.65[67]

1.91[48]

3.94[100]

3.00[76]

3.00[76]

1116

6.40 [162]HI-DRIVE

3.75 [95]LO-DRIVE

1.25 [31.75]

0.625 [15]

R

C

NM

.25 SQ X 2.25 KEY

FOUR HOLES

6.84 [173]

6.09 [157] 5.10 [129]

HI-DRIVE

LO-DRIVE

PORT

6.40[163]

3.75[95] VARIABLE

3.25[82]

11.50[292]

3.15[80]

2.65[67]

1.91[48]

3.00[76]

3.00[76]

2.29[58]

R

C

NM

.25 SQ X 1.5 KEY

1.125 [28.58]

6.84 [173]

6.09 [157] 5.10 [129]

PORT

4.19 [106]

1.75 [44]

0.625[15]

11.25 [285]

3.25[82]

11.50[292]

3.15[80]

2.65[67]

1.91[48]

3.94[100]

3.00[76]

3.00[76]

1116

6.40 [162]HI-DRIVE

3.75 [95]LO-DRIVE

1.25 [31.75]

0.625 [15]

R

C

NM

.25 SQ X 2.25 KEY

FOUR HOLES

6.84 [173]

6.09 [157] 5.10 [129]

HI-DRIVE

LO-DRIVE

PORT

6.40[163]

3.75[95] VARIABLE


DimensionsAngled Gears


42Gear PumPs

3600 SERIES

IN[MM]

3600 SERIES C NM R PORTS

NO

OU

TBO

ARD

BE

ARIN

G

32

HF & HFRV

20.48[520]

12.25[311]

21.40[544] 3 NPT FLANGE

43 22.10[561]

13.07[332]

23.02[585] 3 NPT FLANGE

48 23.19[589]

13.66[347]

24.21[615] 4 NPT FLANGE

NO

OU

TBO

ARD

BE

ARIN

G

32

HBF & HBFRV

23.67[601]

15.44[392]

24.58[624] 3 NPT FLANGE

43 25.32[643]

16.29[414]

26.24[666] 3 NPT FLANGE

48 27.02[686]

17.38[441]

27.93[709] 4 NPT FLANGE

NO

OU

TBO

ARD

BE

ARIN

G

32

GHBF & GHBFRV

25.82[656]

17.59[447]

26.74[679] 3 NPT FLANGE

43 27.43[697]

18.40[467]

28.35[720] 3 NPT FLANGE

48 28.63[727]

19.00[482]

29.55[751] 4 NPT FLANGE


43GE

AR p

umps

Gear PumPsA SERIES

A Series General Purpose PumpsGeneral Purpose Pumps for Pressure Lubrication, Hydraulic Service, Fuel Supply and General Transfer

Up to 59 GPM • Up to 300 PSIRoper A Series pumps are adaptable to a wide range of applications pumping clean fluids, such as pressure lubrication, hydraulic service, fuel supply or general liquid transfer.

These pumps are designed to operate at standard motor speeds, with provisions for flange or foot mounting. The internal bearings are lubricated by the fluid being pumped. With only two moving parts, the pumps run quietly.

They are manufactured and assembled with close tolerances, and regularly tested to insure dependable performance. Factory assembled for clockwise rotation (facing the pump drive shaft end), most may be reassembled for operation with equal efficiency

in a counter-clockwise rotation.

• Designed to operate at standard motor speeds

• Bi-directional rotation

Quiet-Running Helical GearsAccurate machining insures:

• Proper meshing

• Reduced friction and vibration

• Quiet, efficient operation

• Long life

Long-Lasting Bearing Surfaces• Bearings are special wear-resistant, high-lead

bronze. (Iron and carbon bearings are available.)

• Four heavy duty sleeve bearings give positive support to pumping gears and insure long, efficient service.

Precise, Rugged, Maintenance-Friendly Design• All castings are cast iron.

• Precise manufacturing tolerances provide minimum clearances for maximum pumping efficiency.

• Large, hardened steel dowel pins insure positive alignment between the faceplate, case, and backplate

Features


44Gear PumPs

A SERIES

Model Number Designation

2(i)

AM(ii)

21(iii)

(i) General Arrangement 1 = Foot Mount

17 = Flange Mount

25 = Base Mount

33 = Close Coupled

(ii) Sealing arrangement AL – Lip Seal AM – Mechanical Seal

AP – Packed Box

(iii) Flowrate in US Gallons/100 Revolutions 005 = 0.002 L/Rev 01 = 0.004 L/Rev 02 = 0.008 L/Rev 03 = 0.011 L/Rev 06 = 0.023 L/Rev 08 = 0.034 L/Rev 12 = 0.049 L/Rev 16 = 0.064 L/Rev 21 = 0.083 L/Rev 27 = 0.102 L/Rev 32 = 0.125 L/Rev 40 = 0.159 L/Rev

2 = Foot Mount with Relief Valve

18 = Flange Mount with Relief Valve

26 = Base Mount with Relief Valve

34 = Close Coupled with Relief Valve


45GE

AR p

umps

Gear PumPs A SERIES

MODELTHEORETICAL CAPACITY

MAXIMUM SPEEDMAXIMUM FLOw AT MAXIMUM SPEED (0 DISCHARGE PRESSURE)

MAXIMUM PRESSURE

PORT CONNECTION

005 1.9 CC/REV 3600 RPM .41m3/HR 20 Bar 3/8" BSP

01 3.8 CC/REV 3600 RPM .82m3/HR 20 Bar 3/8" BSP

02 7.6 CC/REV 3600 RPM 1.6m3/HR 20 Bar 3/8" BSP







27 102.2 CC/REV 1800 RPM 11.0m3/HR 10 Bar 2" BSP



STANDARD OPTION

Housing Cast iron Ductile iron

Shafts Steel

Gears Steel Ductile iron

Bearings Bronze ironCarbon

Packing Graphite Filament Teflon

Lip Seal Nitrile viton

Mechanical Seal Carbon/stainless (Nitrile elastomers)

Viton elastomersTeflon elastomers

Performance

Materials of Construction

N.B.: Not all combinations are available on all pump models.


46Gear PumPs

A SERIES

PUMP C R PUMP C R

17A-005 5-9/16[141] 18A-01 6-15/16

[176]

18A-005 6-3/4[171] 17A-02 6-3/16

[157]

17A-01 5-13/16[148] 18A-02 7-3/8

[187]

PUMP C R PUMP C R

1A-06 10-15/32[266] 1A-12 11-5/16

[287]

2A-06 12-5/32[309] 2A-12 13

[330]

1A-08 10-3/4[273] 1A-16 11-7/8

[301

2A-08 12-7/16[316] 2A-16 13-9/16

[344]

PUMP B C F N-M R S

1A-21 3[76]

12-5/8[321]

1[25]

9[229]

1-1/2[38]

2A-21 3[76]

1[25]

9[229]

14-5/16[364]

1-1/2[38]

1A-27 3-3/4[95]

13-3/8[340]

1-3/8[35]

9-3/8[238]

2[51]

2A-27 3-3/4[95]

1-3/8[35]

9-3/8[238]

15-1/16[382]

2[51]

1A-32 4-1/2[114]

14-1/8[359]

1-3/4[44]

9-3/4[248]

2[51]

2A-32 4-1/2[114]

1-3/4[44]

9-3/4[248]

15-13/16[402]

2[51]

1A-40 4-1/2[114]

14-1/8[359]

1-3/4[44]

9-3/4[248]

2[51]

2A-40 4-1/2[114]

1-3/4[44]

9-3/4[248]

15-13/16[402]

2[51]

Size 005 Through 02 (flange mounted)

Size 06 Through 16 (foot mounted)

Size 21 Through 16 (foot mounted)R (RELIEF VALVE)

N-M

B

F

4[102]

S (N.P.T. PORT EACH SIDE)

C (PLAIN)

2-1/4MIN.[57]

3/4[19]

2-3/4[70]

FOUR HOLES 9/16 DIA. [14]

1 DIA.[25.4]

3-3/32[79]

2-3/4[70]

6-1/8[156]

1/2[13]

3-1/2[89]

3-1/2[89]

F

1/4 X 1WOODRUFF KEY

R (RELIEF VALVE)

C (PLAIN)

6-3/8[162]

29/32[23]

2-1/4MIN.[57]

3/4[19]

2-3/4[70]

5/8[16]

5/8[16]

1-1/4 DIA. N.P.T. PORTEACH SIDE [32]


1 DIA.[25.4]

4[102]

2-3/4[70]

6-1/8[156]

1/2[13]

3-1/4[83]

3-1/4[83]

1/4 X 1WOODRUFF KEY

2-1/8[54]

2.123 [54]2.122 [54]

2 (RV)[51]

1-5/8[41]

EQUALLY SPACED ON 2-3/4 DIA. B.C.THREE HOLES 1/4-20 UNC THREAD

3-7/8[98]

3/8N.P.T[10]

R(RV)

3-1/8[79]

1-1/2[38]

1/2[12.7]

1/2[13]

C(PLAIN)

1/8 X 1/2WOODRUFF KEY

R (RELIEF VALVE)

N-M

B

F

4[102]


C (PLAIN)

2-1/4MIN.[57]

3/4[19]

2-3/4[70]


1 DIA.[25.4]

3-3/32[79]

2-3/4[70]

6-1/8[156]

1/2[13]

3-1/2[89]

3-1/2[89]

F

1/4 X 1WOODRUFF KEY

R (RELIEF VALVE)

C (PLAIN)

6-3/8[162]

29/32[23]

2-1/4MIN.[57]

3/4[19]

2-3/4[70]

5/8[16]

5/8[16]



1 DIA.[25.4]

4[102]

2-3/4[70]

6-1/8[156]

1/2[13]

3-1/4[83]

3-1/4[83]

1/4 X 1WOODRUFF KEY

2-1/8[54]

2.123 [54]2.122 [54]

2 (RV)[51]

1-5/8[41]


3-7/8[98]

3/8N.P.T[10]

R(RV)

3-1/8[79]

1-1/2[38]

1/2[12.7]

1/2[13]

C(PLAIN)


R (RELIEF VALVE)

N-M

B

F

4[102]


C (PLAIN)

2-1/4MIN.[57]

3/4[19]

2-3/4[70]


1 DIA.[25.4]

3-3/32[79]

2-3/4[70]

6-1/8[156]

1/2[13]

3-1/2[89]

3-1/2[89]

F

1/4 X 1WOODRUFF KEY

R (RELIEF VALVE)

C (PLAIN)

6-3/8[162]

29/32[23]

2-1/4MIN.[57]

3/4[19]

2-3/4[70]

5/8[16]

5/8[16]



1 DIA.[25.4]

4[102]

2-3/4[70]

6-1/8[156]

1/2[13]

3-1/4[83]

3-1/4[83]

1/4 X 1WOODRUFF KEY

2-1/8[54]

2.123 [54]2.122 [54]

2 (RV)[51]

1-5/8[41]


3-7/8[98]

3/8N.P.T[10]

R(RV)

3-1/8[79]

1-1/2[38]

1/2[12.7]

1/2[13]

C(PLAIN)



47GE

AR p

umps

Gear PumPs A SERIES

PUMP C R PUMP C R

17A-06 6-25/32[172] 17A-12 7-5/8

[194]

18A-06 8-15/32[215] 18A-12 9-5/16

[237]

17A-08 7-1/16[179] 17A-16 8-3/16

[208]

18A-08 8-3/4[222] 18A-18 9-3/4

[248]

PUMP C B-G R S

17A-21 8-15/16[227]

5-5/16[135]

1-1/2[38]

18A-21 5-5/16[135]

10-5/8[270]

1-1/2[38]

17A-27 9-11/16[246]

5-11/16[144]

2[51]

18A-27 5-11/16[144]

11-3/8[289]

2[51]

17A-32 10-7/16[265]

6-1/16[154]

2[51]

18A-32 6-1/16[154]

12-1/8[308]

2[51]

17A-40 10-7/16[265]

6-1/16[154]

2[51]

18A-40 6-1/16[154]

12-1/8[308]

2[51]



Size 003 (flange mounted) Size 003 (foot mounted)

1-9/16[40]

7-7/8 (RV) [200]

6-11/16 (PLAIN) [170]

3-29/32[99]

1-11/16[43]

2.1232.122[54]

1-9/16[40]

2-1/16(RV) [52]

THREE HOLES 1/4-20 UNC THREADEQUALLY SPACED ON 2-3/4 BIA. B.C.

3-1/8[79]

15/32[12]

1/2[12.7]

1-1/4[32]

1-3/4[44]

1/8 X 1/2 WOODRUFF KEY

3/4 N.P.T. (BOTH SIDES)[19]

2-1/16 (RV)[52]

1-9/16[40]

1-7/8[48]

3-21/32[60]

2-3/8[93]

1-7/8[48]

4-1/2[114]

3/8[10]

1-9/16[40]

4-7/8[124]

1-1/4[32]

7-7/8 (RV) [200]

TWO HOLES13/32 DIA. [10]

1/2[12.7]

6-11/16 (PLAIN) [170]


1-3/8[35]

1-29/32[48]

3/4 N.P.T. (BOTH SIDES) [19]

R (RELIEF VALVE)

B-G3-11/16[94]

7/16[11]

3/16[5]

29/32[23]


C (PLAIN)

2-1/4MIN.[57]

3/4[19]

1 DIA.[25.4]

1/4 X 1WOODRUFF KEY

3-1/2[89]

3-1/2[89]

7-1/2 DIA.[191]

SIX HOLES9/16 DIA. [14]EQUALLY SPACEDON 6-7/16 DIA. [164]BOLT CIRCLE

4.000 DIA.3.998

R (RELIEF VALVE)

C (PLAIN)

3-1/4[83]

3-1/4[83]

2-11/16[68]

2-1/4MIN.[57]

3/4[19]

1 DIA.[25.4]

3/16[5]

7/16[11]

29/32[23]

1-1/4 N.P.T.PORT EACH SIDE [32]

3-11/16[94]

7-1/2 DIA. [191]

SIX HOLES 9/16 DIA. [14]EQUALLY SPACED ON 6-7/16 [164] DIA. BOLT CIRCLE

4.000 DIA.3.998

1/4 X 1WOODRUFF KEY

1-9/16[40]

7-7/8 (RV) [200]

6-11/16 (PLAIN) [170]

3-29/32[99]

1-11/16[43]

2.1232.122[54]

1-9/16[40]

2-1/16(RV) [52]


3-1/8[79]

15/32[12]

1/2[12.7]

1-1/4[32]

1-3/4[44]



2-1/16 (RV)[52]

1-9/16[40]

1-7/8[48]

3-21/32[60]

2-3/8[93]

1-7/8[48]

4-1/2[114]

3/8[10]

1-9/16[40]

4-7/8[124]

1-1/4[32]

7-7/8 (RV) [200]


1/2[12.7]

6-11/16 (PLAIN) [170]


1-3/8[35]

1-29/32[48]


R (RELIEF VALVE)

B-G3-11/16[94]

7/16[11]

3/16[5]

29/32[23]


C (PLAIN)

2-1/4MIN.[57]

3/4[19]

1 DIA.[25.4]

1/4 X 1WOODRUFF KEY

3-1/2[89]

3-1/2[89]

7-1/2 DIA.[191]


4.000 DIA.3.998

R (RELIEF VALVE)

C (PLAIN)

3-1/4[83]

3-1/4[83]

2-11/16[68]

2-1/4MIN.[57]

3/4[19]

1 DIA.[25.4]

3/16[5]

7/16[11]

29/32[23]


3-11/16[94]

7-1/2 DIA. [191]


4.000 DIA.3.998

1/4 X 1WOODRUFF KEY

1-9/16[40]

7-7/8 (RV) [200]

6-11/16 (PLAIN) [170]

3-29/32[99]

1-11/16[43]

2.1232.122[54]

1-9/16[40]

2-1/16(RV) [52]


3-1/8[79]

15/32[12]

1/2[12.7]

1-1/4[32]

1-3/4[44]



2-1/16 (RV)[52]

1-9/16[40]

1-7/8[48]

3-21/32[60]

2-3/8[93]

1-7/8[48]

4-1/2[114]

3/8[10]

1-9/16[40]

4-7/8[124]

1-1/4[32]

7-7/8 (RV) [200]


1/2[12.7]

6-11/16 (PLAIN) [170]


1-3/8[35]

1-29/32[48]


R (RELIEF VALVE)

B-G3-11/16[94]

7/16[11]

3/16[5]

29/32[23]


C (PLAIN)

2-1/4MIN.[57]

3/4[19]

1 DIA.[25.4]

1/4 X 1WOODRUFF KEY

3-1/2[89]

3-1/2[89]

7-1/2 DIA.[191]


4.000 DIA.3.998

R (RELIEF VALVE)

C (PLAIN)

3-1/4[83]

3-1/4[83]

2-11/16[68]

2-1/4MIN.[57]

3/4[19]

1 DIA.[25.4]

3/16[5]

7/16[11]

29/32[23]


3-11/16[94]

7-1/2 DIA. [191]


4.000 DIA.3.998

1/4 X 1WOODRUFF KEY

1-9/16[40]

7-7/8 (RV) [200]

6-11/16 (PLAIN) [170]

3-29/32[99]

1-11/16[43]

2.1232.122[54]

1-9/16[40]

2-1/16(RV) [52]


3-1/8[79]

15/32[12]

1/2[12.7]

1-1/4[32]

1-3/4[44]



2-1/16 (RV)[52]

1-9/16[40]

1-7/8[48]

3-21/32[60]

2-3/8[93]

1-7/8[48]

4-1/2[114]

3/8[10]

1-9/16[40]

4-7/8[124]

1-1/4[32]

7-7/8 (RV) [200]


1/2[12.7]

6-11/16 (PLAIN) [170]


1-3/8[35]

1-29/32[48]


R (RELIEF VALVE)

B-G3-11/16[94]

7/16[11]

3/16[5]

29/32[23]


C (PLAIN)

2-1/4MIN.[57]

3/4[19]

1 DIA.[25.4]

1/4 X 1WOODRUFF KEY

3-1/2[89]

3-1/2[89]

7-1/2 DIA.[191]


4.000 DIA.3.998

R (RELIEF VALVE)

C (PLAIN)

3-1/4[83]

3-1/4[83]

2-11/16[68]

2-1/4MIN.[57]

3/4[19]

1 DIA.[25.4]

3/16[5]

7/16[11]

29/32[23]


3-11/16[94]

7-1/2 DIA. [191]


4.000 DIA.3.998

1/4 X 1WOODRUFF KEY


48Gear PumPs

A SERIES

PUMP B C F N-M R S

1AE-19 3[76]

12-5/8[321]

1[25]

9[229]

1-1/2[38]

2AE-19 3[76]

1[25]

9[229]

14-13/16[376]

1-1/2[38]

1AE-29 4-1/2[114]

14-1/8[359]

1-3/4[44]

9-3/4[248]

2[51]

2AE-29 4-1/2[114]

1-3/4[44]

9-3/4[248]

15-13/16[402]

2[51]

Size 19 Through 29 (foot mounted)

Size 54 (foot mounted)

Size 75 (foot mounted)

Ø1.00[25.4]

1-7/8 [48]

3/4[19]

1/4 x 1 WOODRUFF KEY

2 N.P.T. (OPPOSITE SIDE) [51]

2 N.P.T. [51]


1/2 [12.7]

7-1/8[181]

6 [152] 6 [152]

5[127] 4-3/32

[104]

5-3/8 [137] 5-3/8 [137]

4-1/2 [114]

1-3/4 [44]

1-3/4 [44]

12 [305]

9-3/4 [248]

20-5/16 (RELIEF VALVE) [516]

18-5/8 (PLAIN) [473]

1-7/8 [48]

N-M

R(RELIEF VALVE)

B

3/4[19]

C(PLAIN)

Ø1.00[25.4]

3-3/32[79]

4[102]

S(N.P.T. PORT EACH SIDE)


2-3/4 [70] 2-3/4 [70]

3-1/2 [89] 3-1/2 [89]

1/2 [12.7]

6-1/8[156]

1/4 x 1WOODRUFF KEY

4-3/32 [104]

14-1/4 [362]

24-13/16 (RELIEF VALVE) [630]

1-3/4 [44]

1-3/4 [44]

4-1/2 [114]

Ø1.00[25.4]

1-7/8 [48]

23-1/8 (PLAIN) [587]

3/4 [19]

1/4 x 1WOODRUFF KEY

2-1/2 N.P.T. BOTH SIDES [64]


5-3/8 [137]

6 [152] 6 [152]

1/2 [12.7]

5[127]

7-1/8[181]

5-3/8 [137]

Ø1.00[25.4]

1-7/8 [48]

3/4[19]



2 N.P.T. [51]


1/2 [12.7]

7-1/8[181]

6 [152] 6 [152]

5[127] 4-3/32

[104]

5-3/8 [137] 5-3/8 [137]

4-1/2 [114]

1-3/4 [44]

1-3/4 [44]

12 [305]

9-3/4 [248]

20-5/16 (RELIEF VALVE) [516]

18-5/8 (PLAIN) [473]

1-7/8 [48]

N-M

R(RELIEF VALVE)

B

3/4[19]

C(PLAIN)

Ø1.00[25.4]

3-3/32[79]

4[102]



2-3/4 [70] 2-3/4 [70]

3-1/2 [89] 3-1/2 [89]

1/2 [12.7]

6-1/8[156]

1/4 x 1WOODRUFF KEY

4-3/32 [104]

14-1/4 [362]

24-13/16 (RELIEF VALVE) [630]

1-3/4 [44]

1-3/4 [44]

4-1/2 [114]

Ø1.00[25.4]

1-7/8 [48]

23-1/8 (PLAIN) [587]

3/4 [19]

1/4 x 1WOODRUFF KEY



5-3/8 [137]

6 [152] 6 [152]

1/2 [12.7]

5[127]

7-1/8[181]

5-3/8 [137]

Ø1.00[25.4]

1-7/8 [48]

3/4[19]



2 N.P.T. [51]


1/2 [12.7]

7-1/8[181]

6 [152] 6 [152]

5[127] 4-3/32

[104]

5-3/8 [137] 5-3/8 [137]

4-1/2 [114]

1-3/4 [44]

1-3/4 [44]

12 [305]

9-3/4 [248]

20-5/16 (RELIEF VALVE) [516]

18-5/8 (PLAIN) [473]

1-7/8 [48]

N-M

R(RELIEF VALVE)

B

3/4[19]

C(PLAIN)

Ø1.00[25.4]

3-3/32[79]

4[102]



2-3/4 [70] 2-3/4 [70]

3-1/2 [89] 3-1/2 [89]

1/2 [12.7]

6-1/8[156]

1/4 x 1WOODRUFF KEY

4-3/32 [104]

14-1/4 [362]

24-13/16 (RELIEF VALVE) [630]

1-3/4 [44]

1-3/4 [44]

4-1/2 [114]

Ø1.00[25.4]

1-7/8 [48]

23-1/8 (PLAIN) [587]

3/4 [19]

1/4 x 1WOODRUFF KEY



5-3/8 [137]

6 [152] 6 [152]

1/2 [12.7]

5[127]

7-1/8[181]

5-3/8 [137]

3600 SERIES 3600 Series Heavy Duty Pumps · PDF fileCOmPLeTe PaCKaGeD PumP sOLuTIONs 1300...

Documents

Transcript of 3600 SERIES 3600 Series Heavy Duty Pumps · PDF fileCOmPLeTe PaCKaGeD PumP sOLuTIONs 1300...