32LM660S, 660T, 669S, 669T

Printed in KoreaP/NO : MFL67360905 (1204-REV00)

CHASSIS : LD22E

MODEL: 32LM660S/660T/669S/669TMODEL: 32LM660S/660T-ZA 32LM669S/669T-ZC

CAUTIONBEFORE SERVICING THE CHASSIS,READ THE SAFETY PRECAUTIONS IN THIS MANUAL.

LED LCD TVSERVICE MANUAL

North/Latin America http://aic.lgservice.comEurope/Africa http://eic.lgservice.comAsia/Oceania http://biz.lgservice.com

Internal Use Only

- 2 - LGE Internal Use OnlyCopyright © LG Electronics. Inc. All rights reserved.Only for training and service purposes

CONTENTS

CONTENTS .............................................................................................. 2

SAFETY PRECAUTIONS ........................................................................ 3

SERVICING PRECAUTIONS .................................................................... 4

SPECIFICATION ....................................................................................... 6

ADJUSTMENT INSTRUCTION .............................................................. 10

SCREW ASSEMBLY WORKING GUIDE .............................................. 18

BLOCK DIAGRAM .................................................................................. 19

EXPLODED VIEW .................................................................................. 20

SCHEMATIC CIRCUIT DIAGRAM ..............................................................


Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the Schematic Diagram and Exploded View.It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent Shock, Fire, or other Hazards. Do not modify the original design without permission of manufacturer.

General Guidance

An isolation Transformer should always be used during the servicing of a receiver whose chassis is not isolated from the AC power line. Use a transformer of adequate power rating as this protects the technician from accidents resulting in personal injury from electrical shocks.

It will also protect the receiver and it's components from being damaged by accidental shorts of the circuitry that may be inadvertently introduced during the service operation.

If any fuse (or Fusible Resistor) in this TV receiver is blown, replace it with the specified.

When replacing a high wattage resistor (Oxide Metal Film Resistor, over 1 W), keep the resistor 10 mm away from PCB.

Keep wires away from high voltage or high temperature parts.

Before returning the receiver to the customer,

always perform an AC leakage current check on the exposed metallic parts of the cabinet, such as antennas, terminals, etc., to be sure the set is safe to operate without damage of electrical shock.

Leakage Current Cold Check(Antenna Cold Check)With the instrument AC plug removed from AC source, connect an electrical jumper across the two AC plug prongs. Place the AC switch in the on position, connect one lead of ohm-meter to the AC plug prongs tied together and touch other ohm-meter lead in turn to each exposed metallic parts such as antenna terminals, phone jacks, etc. If the exposed metallic part has a return path to the chassis, the measured resistance should be between 1 MΩ and 5.2 MΩ. When the exposed metal has no return path to the chassis the reading must be infinite.An other abnormality exists that must be corrected before the receiver is returned to the customer.

Leakage Current Hot Check (See below Figure) Plug the AC cord directly into the AC outlet.

Do not use a line Isolation Transformer during this check. Connect 1.5 K / 10 watt resistor in parallel with a 0.15 uF capacitor between a known good earth ground (Water Pipe, Conduit, etc.) and the exposed metallic parts.Measure the AC voltage across the resistor using AC voltmeter with 1000 ohms/volt or more sensitivity.Reverse plug the AC cord into the AC outlet and repeat AC voltage measurements for each exposed metallic part. Any voltage measured must not exceed 0.75 volt RMS which is corresponds to 0.5 mA.In case any measurement is out of the limits specified, there is possibility of shock hazard and the set must be checked and repaired before it is returned to the customer.

Leakage Current Hot Check circuit

IMPORTANT SAFETY NOTICE

SAFETY PRECAUTIONS


SERVICING PRECAUTIONSCAUTION: Before servicing receivers covered by this service manual and its supplements and addenda, read and follow the SAFETY PRECAUTIONS on page 3 of this publication.NOTE: If unforeseen circumstances create conflict between the following servicing precautions and any of the safety precautions on page 3 of this publication, always follow the safety precautions. Remember: Safety First.

General Servicing Precautions1. Always unplug the receiver AC power cord from the AC power

source before;a. Removing or reinstalling any component, circuit board mod-

ule or any other receiver assembly.b. Disconnecting or reconnecting any receiver electrical plug or

other electrical connection.c. Connecting a test substitute in parallel with an electrolytic

capacitor in the receiver.CAUTION: A wrong part substitution or incorrect polarity installation of electrolytic capacitors may result in an explo-sion hazard.

2. Test high voltage only by measuring it with an appropriate high voltage meter or other voltage measuring device (DVM, FETVOM, etc) equipped with a suitable high voltage probe.Do not test high voltage by "drawing an arc".

3. Do not spray chemicals on or near this receiver or any of its assemblies.

4. Unless specified otherwise in this service manual, clean electrical contacts only by applying the following mixture to the contacts with a pipe cleaner, cotton-tipped stick or comparable non-abrasive applicator; 10 % (by volume) Acetone and 90 % (by volume) isopropyl alcohol (90 % - 99 % strength)CAUTION: This is a flammable mixture.Unless specified otherwise in this service manual, lubrication of contacts in not required.

5. Do not defeat any plug/socket B+ voltage interlocks with which receivers covered by this service manual might be equipped.

6. Do not apply AC power to this instrument and/or any of its electrical assemblies unless all solid-state device heat sinks are correctly installed.

7. Always connect the test receiver ground lead to the receiver chassis ground before connecting the test receiver positive lead.Always remove the test receiver ground lead last.

8. Use with this receiver only the test fixtures specified in this service manual.CAUTION: Do not connect the test fixture ground strap to any heat sink in this receiver.

Electrostatically Sensitive (ES) DevicesSome semiconductor (solid-state) devices can be damaged eas-ily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and semiconductor “chip” components. The following techniques should be used to help reduce the incidence of component dam-age caused by static by static electricity.1. Immediately before handling any semiconductor component or

semiconductor-equipped assembly, drain off any electrostatic charge on your body by touching a known earth ground. Alter-natively, obtain and wear a commercially available discharging wrist strap device, which should be removed to prevent poten-tial shock reasons prior to applying power to the unit under test.

2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil, to prevent electrostatic charge buildup or expo-sure of the assembly.

3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.

4. Use only an anti-static type solder removal device. Some solder removal devices not classified as “anti-static” can generate electrical charges sufficient to damage ES devices.

5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.

6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacement ES devices are packaged with leads electri-cally shorted together by conductive foam, aluminum foil or comparable conductive material).

7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to the chassis or circuit assembly into which the device will be installed.CAUTION: Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.

8. Minimize bodily motions when handling unpackaged replace-ment ES devices. (Otherwise harmless motion such as the brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity suf-ficient to damage an ES device.)

General Soldering Guidelines1. Use a grounded-tip, low-wattage soldering iron and appropriate

tip size and shape that will maintain tip temperature within the range or 500 °F to 600 °F.

2. Use an appropriate gauge of RMA resin-core solder composed of 60 parts tin/40 parts lead.

3. Keep the soldering iron tip clean and well tinned.4. Thoroughly clean the surfaces to be soldered. Use a mall wire-

bristle (0.5 inch, or 1.25 cm) brush with a metal handle.Do not use freon-propelled spray-on cleaners.

5. Use the following unsoldering techniquea. Allow the soldering iron tip to reach normal temperature.

(500 °F to 600 °F)b. Heat the component lead until the solder melts.c. Quickly draw the melted solder with an anti-static, suction-

type solder removal device or with solder braid.CAUTION: Work quickly to avoid overheating the circuit board printed foil.

6. Use the following soldering technique.a. Allow the soldering iron tip to reach a normal temperature

(500 °F to 600 °F)b. First, hold the soldering iron tip and solder the strand against

the component lead until the solder melts.c. Quickly move the soldering iron tip to the junction of the

component lead and the printed circuit foil, and hold it there only until the solder flows onto and around both the compo-nent lead and the foil.CAUTION: Work quickly to avoid overheating the circuit board printed foil.

d. Closely inspect the solder area and remove any excess or splashed solder with a small wire-bristle brush.


IC Remove/ReplacementSome chassis circuit boards have slotted holes (oblong) through which the IC leads are inserted and then bent flat against the cir-cuit foil. When holes are the slotted type, the following technique should be used to remove and replace the IC. When working with boards using the familiar round hole, use the standard technique as outlined in paragraphs 5 and 6 above.

Removal1. Desolder and straighten each IC lead in one operation by

gently prying up on the lead with the soldering iron tip as the solder melts.

2. Draw away the melted solder with an anti-static suction-type solder removal device (or with solder braid) before removing the IC.

Replacement1. Carefully insert the replacement IC in the circuit board.2. Carefully bend each IC lead against the circuit foil pad and

solder it.3. Clean the soldered areas with a small wire-bristle brush.

(It is not necessary to reapply acrylic coating to the areas).

"Small-Signal" Discrete TransistorRemoval/Replacement1. Remove the defective transistor by clipping its leads as close

as possible to the component body.2. Bend into a "U" shape the end of each of three leads remaining

on the circuit board.3. Bend into a "U" shape the replacement transistor leads.4. Connect the replacement transistor leads to the corresponding

leads extending from the circuit board and crimp the "U" with long nose pliers to insure metal to metal contact then solder each connection.

Power Output, Transistor DeviceRemoval/Replacement1. Heat and remove all solder from around the transistor leads.2. Remove the heat sink mounting screw (if so equipped).3. Carefully remove the transistor from the heat sink of the circuit

board.4. Insert new transistor in the circuit board.5. Solder each transistor lead, and clip off excess lead.6. Replace heat sink.

Diode Removal/Replacement1. Remove defective diode by clipping its leads as close as pos-

sible to diode body.2. Bend the two remaining leads perpendicular y to the circuit

board.3. Observing diode polarity, wrap each lead of the new diode

around the corresponding lead on the circuit board.4. Securely crimp each connection and solder it.5. Inspect (on the circuit board copper side) the solder joints of

the two "original" leads. If they are not shiny, reheat them and if necessary, apply additional solder.

Fuse and Conventional ResistorRemoval/Replacement1. Clip each fuse or resistor lead at top of the circuit board hollow

stake.2. Securely crimp the leads of replacement component around

notch at stake top.

3. Solder the connections.CAUTION: Maintain original spacing between the replaced component and adjacent components and the circuit board to prevent excessive component temperatures.

Circuit Board Foil RepairExcessive heat applied to the copper foil of any printed circuit board will weaken the adhesive that bonds the foil to the circuit board causing the foil to separate from or "lift-off" the board. The following guidelines and procedures should be followed whenever this condition is encountered.

At IC ConnectionsTo repair a defective copper pattern at IC connections use the following procedure to install a jumper wire on the copper pattern side of the circuit board. (Use this technique only on IC connec-tions).

1. Carefully remove the damaged copper pattern with a sharp knife. (Remove only as much copper as absolutely necessary).

2. carefully scratch away the solder resist and acrylic coating (if used) from the end of the remaining copper pattern.

3. Bend a small "U" in one end of a small gauge jumper wire and carefully crimp it around the IC pin. Solder the IC connection.

4. Route the jumper wire along the path of the out-away copper pattern and let it overlap the previously scraped end of the good copper pattern. Solder the overlapped area and clip off any excess jumper wire.

At Other ConnectionsUse the following technique to repair the defective copper pattern at connections other than IC Pins. This technique involves the installation of a jumper wire on the component side of the circuit board.

1. Remove the defective copper pattern with a sharp knife.Remove at least 1/4 inch of copper, to ensure that a hazardous condition will not exist if the jumper wire opens.

2. Trace along the copper pattern from both sides of the pattern break and locate the nearest component that is directly con-nected to the affected copper pattern.

3. Connect insulated 20-gauge jumper wire from the lead of the nearest component on one side of the pattern break to the lead of the nearest component on the other side.Carefully crimp and solder the connections.CAUTION: Be sure the insulated jumper wire is dressed so the it does not touch components or sharp edges.


SPECIFICATIONNOTE : Specifications and others are subject to change without notice for improvement.

1. Application rangeThis specification is applied to the LCD TV used LD22E chassis.

2. Requirement for TestEach part is tested as below without special appointment.

1) Temperature: 25 °C ± 5 °C(77 °F ± 9 °F), CST: 40 °C ± 5 °C2) Relative Humidity: 65 % ± 10 %3) Power Voltage

: Standard input voltage (AC 100-240 V~, 50/60 Hz)* Standard Voltage of each products is marked by models.

4) Specification and performance of each parts are followed each drawing and specification by part number in accordance with BOM.

5) The receiver must be operated for about 20 minutes prior to the adjustment.

3. Test method1) Performance: LGE TV test method followed 2) Demanded other specification

- Safety : CE, IEC specification- EMC : CE, IEC - Wireless : Wireless HD Specification (Option)

4. Model General SpecificationNo. Item Specification Remarks

1 Market EU(PAL Market-36Countries)

DTV & Analog (Total 37 countries)DTV (MPEG2/4, DVB-T) : 30 countriesGermany, Netherland, Switzerland, Hungary, Austria, Slovenia, Bulgaria, France, Spain, Italy, Belgium, Russia, Luxemburg, Greece, Czech, Croatia, Turkey, Moroco, Ire-land, Latvia, Estonia, Lithuania, Poland, Portugal, Romania, Albania, Bosnia, Serbia, Slovakia, Beralus

DTV (MPEG2/4, DVB-T2) : 7 countriesUK, Sweden, Denmark, Finland, Norway, Ukraine, Kaza-khstan, Ireland

DTV (MPEG2/4, DVB-C) : 37 countriesGermany, Netherland, Switzerland, Hungary, Austria, Slovenia, Bulgaria, France, Spain, Italy, Belgium, Russia, Luxemburg, Greece, Czech, Croatia, Turkey, Moroco, Ire-land, Latvia, Estonia, Lithuania, Poland, Portugal, Romania, Albania, Bosnia, Serbia, Slovakia, Beralus, UK, Sweden, Denmark, Finland, Norway, Ukraine, Kazakhstan

DTV (MPEG2/4,DVB-S) : 30 countriesGermany, Netherland, Switzerland, Hungary, Austria, Slovenia, Bulgaria, France, Spain, Italy, Belgium, Russia, Luxemburg, Greece, Czech, Croatia, Turkey, Moroco, Ire-land, Latvia, Estonia, Lithuania, Poland, Portugal, Romania, Albania, Bosnia, Serbia, Slovakia, Beralus

Supported satellite : 22 satellitesHISPASAT 1C/1D, ATLANTIC BIRD 2, NILESAT 101/102, ATLANTIC BIRD 3, AMOS 2/3, THOR 5/6, IRIUS 4, EU-TELSAT-W3A, EUROBIRD 9°, EUTELSAT-W2A, HOTBIRD 6/8/9, EUTELSAT-SESAT, ASTRA 1L/H/M/KR, ASTRA 3°/3B, BADR 4/6, ASTRA 2D, EUROBIRD 3, EUTELSAT-W7, HELLASSAT 2, EXPRESS AM1, TURKSAT 2°/3°, INTERSAT10


No. Item Specification Remarks

2 Broadcasting system

1) PAL-BG2) PAL-DK3) PAL-I/I’4) SECAM L/L’, DK, BG, I5) DVB-T6) DVB-C7) DVB-T28) DVB-S

DVB-S: Satellite

3 Receiving systemAnalog : Upper HeterodyneDigital : COFDM, QAM

DVB-T- Guard Interval(Bitrate_Mbit/s)1/4, 1/8, 1/16, 1/32- Modulation : Code RateQPSK : 1/2, 2/3, 3/4, 5/6, 7/816-QAM : 1/2, 2/3, 3/4, 5/6, 7/864-QAM : 1/2, 2/3, 3/4, 5/6, 7/8

DVB-T2- Guard Interval(Bitrate_Mbit/s) 1/4, 1/8, 1/16, 1/32, 1/128, 19/128, 19/256,- Modulation : Code Rate QPSK : 1/2, 2/5, 2/3, 3/4, 5/6 16-QAM : 1/2, 2/5, 2/3, 3/4, 5/6 64-QAM : 1/2, 2/5, 2/3, 3/4, 5/6 256-QAM : 1/2, 2/5, 2/3, 3/4, 5/6

DVB-C- Symbolrate : 4.0Msymbols/s to 7.2Msymbols/s- Modulation : 16QAM, 64-QAM, 128-QAM and 256-QAM

DVB-S/S2- symbolrate DVB-S2 (8PSK / QPSK) : 2 ~ 45Msymbol/s DVB-S (QPSK) : 2 ~ 45Msymbol/s- viterbi DVB-S mode : 1/2, 2/3, 3/4, 5/6, 7/8 DVB-S2 mode : 1/2, 2/3, 3/4, 3/5, 4/5, 5/6, 8/9, 9/10

4 Scart Gender Jack (1EA) PAL, SECAM Scart jack is Full scart and support MNT/DTV-OUT(not support DTV Auto AV)

5 Video Input RCA(1EA) PAL, SECAM, NTSC 4 System : PAL, SECAM, NTSC, PAL60AV gender jack 1EA

6 Head phone outAntenna, AV1, AV2, Component, RGB, HDMI1, HDMI2, HDMI3, HDMI4, USB1, USB2, USB3

7 Component Input (1EA) Y/Cb/CrY/Pb/Pr

Component Gender 1EA

8 RGB Input RGB-PC Analog(D-SUB 15PIN)

9 HDMI Input (4EA)

HDMI1-DTVHDMI2-DTVHDMI3-DTVHDMI4-DTV

HDMI4 : PC support(HDMI version 1.3)Support HDCP

10 Audio Input (3EA)RGB/DVI AudioComponentAV

L/R Input

11 SPDIF out (1EA) SPDIF out12 USB (3EA) EMF, DivX HD, For SVC (download) JPEG, MP3, DivX HD13 Ethernet Connect(1EA) Ethernet Connect


5. Component Video Input (Y, Cb/Pb, Cr/Pr)

6. RGB input (PC)

No. Resolution H-freq(kHz) V-freq(Hz) Porposed

1 720×480 15.73 60.00 SDTV, DVD 480i

2 720×480 15.63 59.94 SDTV, DVD 480i

3 720×480 31.47 59.94 480p

4 720×480 31.50 60.00 480p

5 720×576 15.625 50.00 SDTV, DVD 625 Line

6 720×576 31.25 50.00 HDTV 576p

7 1280×720 45.00 50.00 HDTV 720p

8 1280×720 44.96 59.94 HDTV 720p

9 1280×720 45.00 60.00 HDTV 720p

10 1920×1080 31.25 50.00 HDTV 1080i

11 1920×1080 33.75 60.00 HDTV 1080i

12 1920×1080 33.72 59.94 HDTV 1080i

13 1920×1080 56.250 50 HDTV 1080p

14 1920×1080 67.5 60 HDTV 1080p

No. Resolution H-freq(kHz) V-freq.(Hz) Proposed

1 640 x 350 @70Hz 31.468 70.09 EGA

2 720 x 400 @70Hz 31.469 70.08 DOS

3 640 x 480 @60Hz 31.469 59.94 VESA(VGA)

4 800 x 600 @60Hz 37.879 60.31 VESA(SVGA)

5 1024 x 768 @60Hz 48.363 60.00 VESA(XGA)

6 1152 x 864 @60Hz 54.348 60.053 VESA

7 1360 x 768 @60Hz 47.712 60.015 VESA(WXGA)

8 1920 x 1080 @60Hz 67.5 60.00 WUXGA(Reduced Blanking))


7. HDMI Input7.1. DTV mode

No. Resolution H-freq(kHz) V-freq.(kHz) Proposed

1. 640*480 31.469 / 31.5 59.94/60 SDTV 480P

2. 720*480 31.469 / 31.5 59.94 / 60 SDTV 480P

3. 720*576 31.25 50 SDTV 576P

4. 720*576 15.625 50 SDTV 576I

5. 1280*720 37.500 50 HDTV 720P

6. 1280*720 44.96 / 45 59.94 / 60 HDTV 720P

7. 1920*1080 33.72 / 33.75 59.94 / 60 HDTV 1080I

8. 1920*1080 28.125 50.00 HDTV 1080I

9. 1920*1080 26.97 / 27 23.97 / 24 HDTV 1080P

10. 1920*1080 25 HDTV 1080P

11. 1920*1080 33.716 / 33.75 29.976 / 30.00 HDTV 1080P

12. 1920*1080 56.250 50 HDTV 1080P

13. 1920*1080 67.43 / 67.5 59.94 / 60 HDTV 1080P

No. Resolution H-freq(kHz) V-freq.(Hz) Proposed

1 640 x 350 @70Hz 31.468 70.09 EGA

2 720 x 400 @70Hz 31.469 70.08 DOS

3 640 x 480 @60Hz 31.469 59.94 VESA(VGA)

4 800 x 600 @60Hz 37.879 60.31 VESA(SVGA)

5 1024 x 768 @60Hz 48.363 60.00 VESA(XGA)

6 1152 x 864 @60Hz 54.348 60.053 VESA

7 1280 x 1024 @60Hz 63.981 60.020 VESA(SXGA)

8 1360 x 768 @60Hz 47.712 60.015 VESA(WXGA)

9 1920 x 1080 @60Hz 67.5 60.00 WUXGA(Reduced Blanking))

7.2. PC mode


ADJUSTMENT INSTRUCTION1. Application Range

This specification sheet is applied to all of the LED LCD TV with LD22E chassis.

2. Designation(1) Because this is not a hot chassis, it is not necessary to

use an isolation transformer. However, the use of isolation transformer will help protect test instrument.

(2) Adjustment must be done in the correct order. (3) The adjustment must be performed in the circumstance of

25 °C ± 5 °C of temperature and 65 % ± 10 % of relative humidity if there is no specific designation.

(4) The input voltage of the receiver must keep AC 100-240 V~, 50/60 Hz.

(5) The receiver must be operated for about 5 minutes prior to the adjustment when module is in the circumstance of over 15.

In case of keeping module is in the circumstance of 0 °C, it should be placed in the circumstance of above 15 °C for 2 hours.

In case of keeping module is in the circumstance of below -20 °C, it should be placed in the circumstance of above 15 °C for 3 hours.

[Caution] When still image is displayed for a period of 20 minutes or longer (Especially where W/B scale is strong. Digital pattern 13ch and/or Cross hatch pattern 09ch), there can some afterimage in the black level area.

3. Automatic Adjustment3.1. ADC Adjustment3.1.1. Overview

ADC adjustment is needed to find the optimum black level and gain in Analog-to-Digital device and to compensate RGB deviation.

3.1.2. Equipment & Condition(1) USB to RS-232C Jig(2) MSPG-925 Series Pattern Generator(MSPG-925FA,

pattern - 65)- Resolution : 1080P Comp1 1920*1080 RGB- Pattern : Horizontal 100% Color Bar Pattern- Pattern level : 0.7 ± 0.1 Vp-p- Image

3.1.3. Adjustment(1) Adjustment method

Don’t need to adjust ADC because there is data in OTP and adjusted initially.

Check ADC adjustment1) Press In start key on the Adj. Remote Control, then

Adjust ADC(OTP) status is displayed on “1.Adjustment check”. Select “2.ADC Data”, then ADC data is displayed.

2) Press Adj. key on the Adjustmetn Remote Control, and select “9.ADC Calibration”. Set up the ADC Type to OTP, then Select [Start] button by pressing Enter key, Component and RGB are Writed and display Success or NG.

(2) Adj. protocol

Ref.) ADC Adj. RS232C Protocol_Ver1.0

(3) Adj. order- aa 00 00 [Enter ADC adj. mode]- xb 00 04 [Change input source to Component1 (480i&

1080p)]- ad 00 10 [Adjust 480i&1080p Comp1]- xb 00 06 [Change input source to RGB(1024*768)]- ad 00 10 [Adjust 1920*1080 RGB]- ad 00 90 End adj.

Protocol Command Set ACK

Enter adj. mode aa 00 00 a 00 OK00x

Source changexb 00 04 b 00 OK04x (Adjust 480i, 1080p Comp1 )

xb 00 06 b 00 OK06x (Adjust 1920*1080 RGB)

Begin adj. ad 00 10

Return adj. result OKx (Case of Success)NGx (Case of Fail)

Read adj. data

(main)ad 00 20

(main)000000000000000000000000007c007b006dx

(sub ) (Sub)000000070000000000000000007c00830077xad 00 21

Confirm adj. ad 00 99

NG 03 00x (Fail)NG 03 01x (Fail)NG 03 02x (Fail)OK 03 03x (Success)

End adj. aa 00 90 a 00 OK90x


3.2. MAC address D/L, CI+ key D/L, Widevine key D/L, ESN D/L

Connect: USB portCommunication Prot connection Com 1,2,3,4 and 115200(Baudrate)Mode check: Online Only Check the test process: DETECT -> MAC -> CI -> Widevine

-> ESN. Play: START. Result: Ready, Test, OK or NG. Printer Out (MAC Address Label)

3.3. LAN3.3.1. Equipment & Condition

Each other connection to LAN Port of IP Hub and Jig

3.3.2. LAN inspection solution LAN Port connection with PCB Network setting at MENU Mode of TV Setting automatic IP Setting state confirmation

→ If automatic setting is finished, you confirm IP and MAC Address.

3.3.3. WIDEVINE key Inspection- Confirm key input data at the "IN START" MENU Mode.

3.4. LAN PORT INSPECTION(PING TEST)Connect SET → LAN port == PC → LAN Port

3.4.1. Equipment setting(1) Play the LAN Port Test PROGRAM.(2) Input IP set up for an inspection to Test Program.

*IP Number : 12.12.2.2

3.4.2. LAN PORT inspection(PING TEST)(1) Play the LAN Port Test Program.(2) Connect each other LAN Port Jack.(3) Play Test (F9) button and confirm OK Message.(4) Remove LAN cable.

Play: Start

SET PC


3.5. Model name & Serial number Download3.5.1. Model name & Serial number D/L

Press "Power on" key of service remote control.(Baud rate : 115200 bps)

Connect RS232 Signal Cable to RS-232 Jack. Write Serial number by use RS-232. Must check the serial number at Instart menu.

3.5.2. Method & notice(1) Serial number D/L is using of scan equipment.(2) Setting of scan equipment operated by Manufacturing

Technology Group.(3) Serial number D/L must be conformed when it is produced

in production line, because serial number D/L is mandatory by D-book 4.0

* Manual Download (Model Name and Serial Number)If the TV set is downloaded by OTA or service man, sometimes model name or serial number is initialized.(Not always)It is impossible to download by bar code scan, so It need Manual download.1) Press the "Instart" key of Adjustment remote control.2) Go to the menu "5.Model Number D/L" like below photo.3) Input the Factory model name(ex 47LM760S-ZB-A) or

Serial number like photo.

4) Check the model name Instart menu. → Factory name displayed. (ex 47LM760S-ZB)

5) Check the Diagnostics.(DTV country only) → Buyer model displayed. (ex 47LM760S-ZB)

3.6. CI+ Key checking method- Check the Section 3.2Check whether the key was downloaded or not at ‘In Start’ menu. (Refer to below).

=> Check the Download to CI+ Key value in LGset.

3.6.1. Check the method of CI+ Key value(1) Check the method on Instart menu(2) Check the method of RS232C Command

1) Into the main ass’y mode(RS232: aa 00 00)

2) Check the key download for transmitted command (RS232: ci 00 10)

3) Result value- Normally status for download : OKx- Abnormally status for download : NGx

3.6.2. Check the method of CI+ key value(RS232)1) Into the main ass’y mode(RS232: aa 00 00)

2) Check the mothed of CI+ key by command (RS232: ci 00 20)

3) Result valuei 01 OK 1d1852d21c1ed5dcx

3.7. WIFI MAC ADDRESS CHECK(1) Using RS232

(2) Check the menu on in-start.

CMD 1 CMD 2 Data 0A A 0 0

CMD 1 CMD 2 Data 0C I 1 0

CMD 1 CMD 2 Data 0A A 0 0

CMD 1 CMD 2 Data 0C I 2 0

CI+ Key Value

H-freq(kHz) V-freq.(Hz)

Transmission [A][I][][Set ID][][20][Cr] [O][K][X] or [NG]


4. Manual Adjustment* ADC adjustment is not needed because of OTP(Auto ADC

adjustment)

4.1 EDID(The Extended Display Identification Data)/DDC(Display Data Channel) download

4.1.1. OverviewIt is a VESA regulation. A PC or a MNT will display an optimal resolution through information sharing without any necessity of user input. It is a realization of "Plug and Play".

4.1.2. Equipment- Since embedded EDID data is used, EDID download JIG,

HDMI cable and D-sub cable are not need.- Adjustment remote control

4.1.3. Download method(1) Press "ADJ" key on the Adjustment remote control then

select "10.EDID D/L", By pressing "Enter" key, enter EDID D/L menu.

(2) Select "Start" button by pressing "Enter" key, HDMI1/ HDMI2/ HDMI3/ HDMI4/ RGB are writing and display OK or NG.

4.1.4. EDID DATA(1) 3D EDID DATA

Reference- HDMI1 ~ HDMI4 / RGB - In the data of EDID, bellows may be different by S/W or

Input mode. . Product ID

. Serial No: Controlled on production line.. Month, Year: Controlled on production line:

ex) Week : '01' -> '01'Year : '2012' -> '16' fix

. Model Name(Hex): LGTV

. Checksum: Changeable by total EDID data.

. Vendor Specific(HDMI)1) Deep color (module 10bit)

2) None deep color (module 8bit)

Colorimetry Data Block(HDMI)- The Model not supporting XvYcc(Except for LM7600)

For Analog For HDMI EDID

D-sub to D-sub DVI-D to HDMI or HDMI to HDMI

HEX EDID Table DDC Function

0001 01 00 Analog/Digital

Chassis MODEL NAME(HEX)

LD22E 00 00 00 FC 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20

INPUT MODEL NAME(HEX)

HDMI1 78 03 0C 00 10 00 B8 2D 20 C0 0E 01 4F 3F FC 08 10 18 10 06 10 16 10 28 10

HDMI2 78 03 0C 00 20 00 B8 2D 20 C0 0E 01 4F 3F FC 08 10 18 10 06 10 16 10 28 10

HDMI3 78 03 0C 00 30 00 B8 2D 20 C0 0E 01 4F 3F FC 08 10 18 10 06 10 16 10 28 10

HDMI4 78 03 0C 00 40 00 B8 2D 20 C0 0E 01 4F 3F FC 08 10 18 10 06 10 16 10 28 10

INPUT MODEL NAME(HEX)

HDMI1 78 03 0C 00 10 00 80 2D 20 C0 0E 01 4F 3F FC 08 10 18 10 06 10 16 10 28 10

HDMI2 78 03 0C 00 20 00 80 2D 20 C0 0E 01 4F 3F FC 08 10 18 10 06 10 16 10 28 10

HDMI3 78 03 0C 00 30 00 80 2D 20 C0 0E 01 4F 3F FC 08 10 18 10 06 10 16 10 28 10

HDMI4 78 03 0C 00 40 00 80 2D 20 C0 0E 01 4F 3F FC 08 10 18 10 06 10 16 10 28 10

INPUT MODEL NAME(HEX)HDMI1 E3 05 00 00HDMI2 E3 05 00 00HDMI3 E3 05 00 00HDMI4 E3 05 00 00

12

10 bit/ Xvycc

28 bit/ Xvycc

210 bit/

none XvYcc

28 bit/

none XvYcc3

HDMI1 43 11 49 15 4D XHDMI2 43 01 39 05 3D XHDMI3 43 F1 29 F5 2D XHDMI4 43 E1 19 E5 1D XRGB X X X X X 5C


4.2. White Balance Adjustment4.2.1. Overview

W/B adj. Objective & How-it-works(1) Objective: To reduce each Panel's W/B deviation(2) How-it-works : When R/G/B gain in the OSD is at 192, it

means the panel is at its Full Dynamic Range. In order to prevent saturation of Full Dynamic range and data, one of R/G/B is fixed at 192, and the other two is lowered to find the desired value.

(3) Adjustment condition : normal temperature1) Surrounding Temperature : 25 °C ± 5 °C2) Warm-up time: About 5 Min3) Surrounding Humidity : 20 % ~ 80 %

4.2.2. Equipment(1) Color Analyzer: CA-210 (LED Module : CH 14)(2) Adjustment Computer(During auto adj., RS-232C protocol

is needed)(3) Adjustment Remote control(4) Video Signal Generator MSPG-925F 720p/204-Gray

(Model: 217, Pattern: 49)-> Only when internal pattern is not available

Color Analyzer Matrix should be calibrated using CS-100.

4.2.3. Equipment connection MAP

4.2.4. Adj. Command (Protocol)<Command Format>

- LEN: Number of Data Byte to be sent- CMD: Command- VAL: FOS Data value- CS: Checksum of sent data- A: AcknowledgeEx) [Send: JA_00_DD] / [Ack: A_00_okDDX]

RS-232C Command used during auto-adjustment.

Ex) wb 00 00 -> Begin white balance auto-adj. wb 00 10 -> Gain adj. ja 00 ff -> Adj. data jb 00 c0 ... ... wb 00 1f → Gain adj. completed *(wb 00 20(Start), wb 00 2f(end)) → Off-set adj. wb 00 ff → End white balance auto-adj.

Adj. Map

4.2.5. Adj. method(1) Auto adj. method

1) Set TV in adj. mode using P-Only key.2) Zero calibrate probe then place it on the center of the

Display.3) Connect Cable.(RS-232C to USB)4) Select mode in adj. Program and begin adj.5) When adj. is complete (OK Sign), check adj. status pre

mode. (Warm, Medium, Cool)6) Remove probe and RS-232C cable to complete adj. W/B Adj. must begin as start command “wb 00 00” , and

finish as end command “wb 00 ff”, and Adj. offset if need.

(2) Manual adjustment. method1) Set TV in Adj. mode using P-Only key.2) Zero Calibrate the probe of Color Analyzer, then place it

on the center of LCD module within 10 cm of the surface.3) Press ADJ key → EZ adjust using adj. R/C → 7. White-

Balance then press the cursor to the right(key ).(When right key() is pressed 216 Gray internal pattern will be displayed)

4) One of R Gain / G Gain / B Gain should be fixed at 192, and the rest will be lowered to meet the desired value.

5) Adjustment is performed in COOL, MEDIUM, WARM 3 modes of color temperature.

If internal pattern is not available, use RF input. In EZ Adj. menu 7.White Balance, you can select one of 2 Test-pattern: ON, OFF. Default is inner(ON). By selecting OFF, you can adjust using RF signal in 216 Gray pattern.

START 6E A 50 A LEN A 03 A CMD A 00 A VAL A CS STOP

Color Analyzer

Computer

Pat tern Generator

RS-232C

RS-232C

RS-232C

Probe

Signal Source

* If TV internal pattern is used, not needed

RS-232C COMMAND[CMD ID DATA] Explantion

wb 00 00 Begin White Balance adjustmentwb 00 10 Gain adjustment(internal white pattern)wb 00 1f Gain adjustment completedwb 00 20 Offset adjustment(internal white pattern)wb 00 2f Offset adjustment completed

wb 00 ff End White Balance adjustment(internal pattern disappears )

Adj. item Command(lower caseASCII)

Data Range(Hex.)

Default(Decimal)

CMD1 CMD2 MIN MAX

Cool

R Gain j g 00 C0G Gain j h 00 C0B Gain j i 00 C0R CutG CutB Cut

Medium

R Gain j a 00 C0G Gain j b 00 C0B Gain j c 00 C0R CutG CutB Cut

Warm

R Gain j d 00 C0G Gain j e 00 C0B Gain j f 00 C0R CutG Cut


Adjustment condition and cautionary items1) Lighting condition in surrounding area

Surrounding lighting should be lower 10 lux. Try to isolate adj. area into dark surrounding.

2) Probe location: Color Analyzer(CA-210) probe should be within 10 cm and perpendicular of the module surface.(80° ~ 100°)

3) Aging time- After Aging Start, Keep the Power ON status during 5 Minutes.

- In case of LCD, Back-light on should be checked using no signal or Full-white pattern.

4.2.6. Reference(White balance adjusmtment coordinate and color temperature)

Luminance : 204 Gray Standard color coordinate and temperature using CS-1000

(over 26 inch)

Standard color coordinate and temperature using CA-210(CH 14)

4.2.7. LED White balance table- EDGE LED module change color coordinate because of

aging time.- Apply under the color coordinate table, for compensated aging time.

- LM76/67/66 series

4.3. EYE-Q function check(1) Turn on TV.(2) Press EYE key of Adjustment remote control.(3) Cover the Eye Q II sensor on the front of the using your

hand and wait for 6 seconds.(4) Confirm that R/G/B value is lower than 10 of the "Raw

Data (Sensor data, Back light)". If after 6 seconds, R/G/B value is not lower than 10, replace Eye Q II sensor.

(5) Remove your hand from the Eye Q II sensor and wait for 6 seconds.

(6) Confirm that "ok" pop up. If change is not seen, replace Eye Q II sensor.

4.4. Local Dimming Function CheckStep 1) Turn on TV.Step 2) Press “TILT” key on the Adj. R/C.Step 3) At the Local Dimming mode, module Edge Backlight

moving right to left Back light of IOP module moving.Step 4) Confirm the Local Dimming mode.Step 5) Press "exit" key.

4.5. Magic Motion Remote control test(1) Equipment : RF Remote control for test, IR-KEY-Code

Remote control for test(2) You must confirm the battery power of RF-Remote control

before test(recommend that change the battery per every lot)(3) Sequence (test)

1) if you select the "Start(Wheel)" key on the Adjustment remote control, you can pairing with the TV SET.

2) You can check the cursor on the TV Screen, when select the "Wheel" key on the Adjustment remote control.

3) You must remove the pairing with the TV Set by select "Mute" key on the Adjustment remote control

ModeCoordinate

Temp ∆uvx y

Cool 0.269 0.273 13000 K 0.0000 Medium 0.285 0.293 9300 K 0.0000 Warm 0.313 0.329 6500 K 0.0000

ModeCoordinate

Temp ∆uvx y

Cool 0.269 ± 0.002 0.273 ± 0.002 13000 K 0.0000 Medium 0.285 ± 0.002 0.293 ± 0.002 9300 K 0.0000 Warm 0.313 ± 0.002 0.329 ± 0.002 6500 K 0.0000

GP4Aging time(Min)

Cool Medium WarmX y x y x y

269 273 285 293 313 3291 0-2 283 293 299 313 320 3392 3-5 282 291 298 311 319 3373 6-9 281 290 297 310 318 3364 10-19 279 289 295 309 316 3355 20-35 277 284 293 304 314 3306 36-49 274 279 290 299 311 3257 50-79 271 277 287 297 308 3238 80-119 270 274 286 294 307 3209 Over 120 269 273 285 293 306 319

Local Dimming Demo(Edge LED Model)


4.6. 3D function test(Pattern Generator MSHG-600, MSPG-6100[Support HDMI1.4])* HDMI mode NO. 872 , pattern No.83(1) Please input 3D test pattern like below.

(2) When 3D OSD appear automatically, then select OK key.

(3) Don't wear a 3D Glasses, check the picture like below.

4.7. Wi-Fi TestStep 1) Turn on TVStep 2) Select Network Connection option in Network Menu.

Step 3) Select Start Connection button in Network Connection.

Step 4) If the system finds any AP like blow PIC, it is working well.

4.8. LNB voltage and 22KHz tone check(only for DVB-S/S2 model) Test method

(1) Set TV in Adj. mode using POWER ON.(2) Connect cable between satellite ANT and test JIG.(3) Press Yellow key(ETC+SWAP) in Adj Remote control to

make LNB on.(4) Check LED light ‘ON’ at 18 V menu.(5) Check LED light ‘ON’ at 22 KHz tone menu.(6) Press Blue key(ETC+PIP INPUT) in Adj Remote control

to make LNB off.(7) Check LED light ‘OFF’ at 18 V menu.(8) Check LED light ‘OFF’ at 22 KHz tone menu.

Test result(1) After press LNB On key, ‘18 V LED’ and ‘22 KHz tone

LED’ should be ON. (2) After press LNB OFF key, ‘18 V LED’ and ‘22 KHz tone

LED’ should be OFF.

4.9. Option selection per country4.9.1. Overview

- Option selection is only done for models in Non-EU

4.9.2. Method(1) Press ADJ key on the Adj. R/C, then select Country Group

Meun(2) Depending on destination, select Country Group Code 04

or Country Group EU then on the lower Country option, select US, CA, MX. Selection is done using +, - or key.

4.10. Tool Option selection Method : Press "ADJ" key on the Adjustment remote control,

then select Tool option.

4.11. Ship-out mode check(In-stop) After final inspection, press "IN-STOP" key of the Adjustment

remote control and check that the unit goes to Stand-by mode.


4.12. GND and Internal Pressure check4.12.1. Method

(1) GND & Internal Pressure auto-check preparation- Check that Power cord is fully inserted to the SET. (If loose, re-insert)

(2) Perform GND & Internal Pressure auto-check- Unit fully inserted Power cord, Antenna cable and A/V

arrive to the auto-check process. - Connect D-terminal to AV JACK TESTER- Auto CONTROLLER(GWS103-4) ON- Perform GND TEST- If NG, Buzzer will sound to inform the operator.- If OK, changeover to I/P check automatically.

(Remove CORD, A/V form AV JACK BOX.)- Perform I/P test- If NG, Buzzer will sound to inform the operator.- If OK, Good lamp will lit up and the stopper will allow the

pallet to move on to next process.

4.12.2. Checkpoint TEST voltage

- GND: 1.5 KV / min at 100 mA- SIGNAL: 3 KV / min at 100 mA

TEST time: 1 second TEST POINT

- GND TEST = POWER CORD GND & SIGNAL CABLE METAL GND

- Internal Pressure TEST = POWER CORD GND & LIVE & NEUTRAL

LEAKAGE CURRENT: At 0.5 mArms

5. Audio

Measurement condition:(1) RF input: Mono, 1 KHz sine wave signal, 100 % Modulation(2) CVBS, Component: 1 KHz sine wave signal 0.5 Vrms(3) RGB PC: 1 KHz sine wave signal 0.7 Vrms

6. USB S/W Download(Service only)(1) Put the USB Stick to the USB socket.(2) Automatically detecting update file in USB Stick.

- If your downloaded program version in USB Stick is Low, it didn't work. But your downloaded version is High, USB data is automatically detecting.

(Download Version High & Power only mode, Set is automatically Download)

(3) Show the message "Copying files from memory".

(4) Updating is starting.

(5) Updating Completed, The TV will restart automatically.(6) If your TV is turned on, check your updated version and

Tool option. (explain the Tool option, next stage)* If downloading version is more high than your TV have, TV

can lost all channel data. In this case, you have to channel recover. if all channel data is cleared, you didn’t have a DTV/ATV test on production line.

* After downloading, have to adjust Tool Option again.(1) Push "IN-START" key in service remote control.(2) Select "Tool Option 1" and push "OK" key.(3) Punch in the number. (Each model has their number)

No. Item Min Typ Max Unit Remark

1.

Audio practical max Output, L/R(Distortion=10% max Output)

9 10 12 W EQ OffAVL OffClear Voice Off8.10 10.8 Vrms

2. Speaker (8ΩImpedance) 9 10 12 W

EQ OffAVL OffClear Voice Off


Screw specification and application situation

<Warning>Check Screw Type When Screw is assembled at 'A' Part. If 'C' Screw is used at the 'A' part, Module will get damaged.

SCREW ASSEMBLY WORKING GUIDE

• FAB30013202(M3*L8, White, Taptite)

• 4EA

EEEE

EEEE

AA AA AA AA

AA

AA

AA AA

AA

AA

AAAA

CC CC CC CC

AA

AA

AA AADD DD DDDD


L/

R I

n

SP

DIF

OU

T

US

B

Au

dio

AM

P(

STA

)I2

S O

ut

MTK

P_

TS

CV

BSP

_TS

T/C

Dem

odIF

(+/-

)

US

B1

RS-

23

2C

PC

-RG

B

PC

-AU

DIO

OP

TIC

LAN

SYST

EMD

DR

3X

1

60

0 X

1

6

(2G

b)

HD

MI1

HD

MI2

HD

MI3

Side Rear

RG

B,H

/V

Eth

ern

et

CV

BS

UA

RT

SYST

EM E

EPR

OM

X 1

(25

6K

b)

HD

MI

MU

X

(HD

CP

EE

PR

OM

)

M-R

emot

e M

odu

le

Air/

Cab

leTU

NER

(T/C

)

TUN

ER(S

2)

DIG

ITAL

DEM

OD

(T/C

)

DVB

-S

ANAL

OG

DEM

OD

DIG

ITAL

DEM

OD

(S2)

TS

_S

/P

US

B2

US

B3

HD

MI4

eMM

CX

1(2

GB

)

US

B_

WIF

I

SYST

EMD

DR

3X

1

60

0 X

16

(2G

b)

DD

R

CO

NTR

OLER

A/

B

SP

ILO

CA

L D

IMM

ING

I2C

Sub

Mic

om(R

ENES

ASA

)

IRR

emot

e C

ontr

ol

SYST

EMD

DR

3X

1

60

0 X

1

6

(2G

b)

SYST

EMD

DR

3X

1

60

0 X

16

(2G

b)

UA

RT

P_

TS

EPI

50

P5

0P

X_

TAL

27

MH

z

BLOCK DIAGRAM


A22

A2

A21

A10

AG1

300

301

200

400

540

521

530

800

810

710

700

910

560

410

570

120

510

501

500

310

* Set

+ S

tand

* Sta

nd B

ase

+ Bo

dy

LV1

LV2

AG2

122

522

123

900

Clip

Typ

e(O

ptio

n)

EXPLODED VIEW

Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the Schematic Diagram and EXPLODED VIEW. It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent X-RADIATION, Shock, Fire, or other Hazards. Do not modify the original design without permission of manufacturer.

IMPORTANT SAFETY NOTICE

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATESSPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FORTHE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

CI_DATA[5]

CI_DATA[7]

MT5369_TS_OUT[2]

CI_DATA[2]

CI_DATA[4]

CI_ADDR[2]

CI_ADDR[10]

MT5369_TS_OUT[1]

CI_ADDR[13]

FE_TS_DATA[7]

CI_ADDR[5]

EMMC_DATA[7]

EMMC_DATA[6]

FE_TS_DATA[5]

CI_ADDR[8]

CI_DATA[0]

CI_ADDR[6]

CI_ADDR[1]

EMMC_DATA[4]

CI_ADDR[11]

CI_ADDR[12]

CI_DATA[1]

EMMC_DATA[2]

FE_TS_DATA[6]

FE_TS_DATA[0]

CI_ADDR[7]

FE_TS_DATA[4]

MT5369_TS_OUT[4]

CI_DATA[3]

EMMC_DATA[3]

EMMC_DATA[5]

FE_TS_DATA[3]

CI_ADDR[0]

MT5369_TS_OUT[7]

CI_ADDR[3]

CI_DATA[6]

FE_TS_DATA[1]

MT5369_TS_OUT[5]

MT5369_TS_OUT[0]

CI_ADDR[9]

CI_ADDR[14]

FE_TS_DATA[2]

MT5369_TS_OUT[3]

CI_ADDR[4]

MT5369_TS_OUT[6]

MODEL_OPT_2

JTRST#

FE_TS_SYNC

STB_SCL

USB_CTL3

SOC_RX

C1160.1uF

R1501K

MODEL_OPT_0

MT5369_TS_VAL

R1471KOPT

/CI_CD2

R15510KOPT

R1662.7KOPT

EMMC_CLK

R1511KOPT

MT5369_TS_SYNC

MT5369_TS_IN[1]

R1654.7K

OSDA0

L/DIM0_MOSI

/USB_OCD3

R172

22

/PCM_CE1

OSDA1

+3.3V_NORMAL

MODEL_OPT_8

MODEL_OPT_6

R1481K

JTMS

SOC_TX

CI_ADDR[0-14]

FE_TS_VAL

R1674.7K

L/DIM0_VS

R103

4.7K

MT5369_TS_OUT[0-7]

MT5369_TS_IN[5]

EMMC_DATA[2-7]

R1684.7KOPT

R1574.7KOPT

R158 33

OPT

MODEL_OPT_1

CI_DATA[0-7]

JTDI

/PCM_IORD

MT5369_MISTRT

MODEL_OPT_1

CI_A_VS1

LED_PWM0

/PCM_REG

MT5369_XTAL_OUT

MT5369_MIVAL_ERR

I2C_SDA5

MT5369_XTAL_IN

AVDD_33SB

JTCLK

MODEL_OPT_5

A_DIM

FE_TS_CLK

USB_CTL2

MT5369_TS_IN[4]

SOC_RESET

/USB_OCD2

MT5369_MCLKI

/USB_OCD1

/PCM_OE

MT5369_TS_CLK

AVDD_33SB

PCM_RST

MODEL_OPT_3

MT5369_TS_IN[6]

USB_CTL1

MODEL_OPT_10

L/DIM0_SCLK

R1531KOPT

LED_PWM1

/PCM_IOWR

JTDO

C1180.1uF

M_REMOTE_TX

OSCL0

VDD3V3

LED_PWM1

/PCM_WE

M_REMOTE_RX

R136 33

MT5369_TS_IN[0]

MODEL_OPT_5

MODEL_OPT_3

MT5369_TS_IN[2]

MT5369_TS_IN[3]

MODEL_OPT_0

+3.3V_NORMAL

ERROR_OUT

MT5369_TS_IN[7]

MODEL_OPT_6

+3.3V_NORMAL

IC104AT24C256C-SSHL-T

NVRAM_ATMEL

3A2

2A1

4GND

1A0

5SDA

6SCL

7WP

8VCC

FE_TS_DATA[0-7]

MODEL_OPT_9

R17410K

OPCTRL3

/PCM_WAIT

EMMC_CLK

/PCM_IRQA

R169 10K

OPT

R171

22

R170 22

OSCL1

PWM_DIM2

R137 33

R1614.7KOPT

R1784.7KOPT

PWM_DIM1

/CI_CD1

LED_PWM0

M_RFModule_ISP

+3.3V_NORMAL

IR

R1541K

C1170.1uF

I2C_SCL5

+3.3V_NORMAL

STB_SDA

X10027MHz

MT5369_XTAL_OUTMT5369_XTAL_IN

+3.3V_NORMAL

R143 33

MTK_JTAG

JTMS

+3.3V_NORMAL

R14410K

R1521K

MTK_JTAG

JTDO

JTRST#

JTCLK

JTDI

AR10010K

R14910K

MTK_JTAG

R14610KMTK_JTAG

R14510K

MTK_JTAG

+3.3V_NORMAL

R1392.7K

OSDA2

I2C_SDA2

R117 33

+3.3V_NORMAL

R115 33

I2C_SDA6

R1882.7K

I2C_SCL4

I2C_SDA4

OSCL2

I2C_SCL5

R122 33

R1602.7K

R116 33

I2C_SDA5

R1422.7K

OSCL0

I2C_SCL2

STB_SDA R111 33

R123 33

R1342.7K

I2C_SDA1

I2C_SCL3R114 33

R110 33

OSCL1

I2C_SCL6

I2C_SDA3

R113 33

R1642.7K

OSDA1

R1732.7K

R1562.7K

R118 33

R1852.7K

OSDA0

R1772.7K

R112 33

I2C_SCL1

R121 33

STB_SCL

R176 10K

SC_ID_SOC

M_RFModule_RESET

R162 10K

R163 10K

/TU_RESET

RF_SWITCH_CTL

AV1_CVBS_DET

OPCTRL3

DSUB_DET

HP_DET

COMP1_DET

SC_DET

OPCTRL_1_SCL

OPCTRL_11_SCL/S2_RESET

SMARTCARD_VCC

SMARTCARD_RST

SMARTCARD_DATA

SMARTCARD_CLK

SMARTCARD_DET

SMARTCARD_PWR_SEL

SMARTCARD_VCC

SMARTCARD_PWR_SEL

SMARTCARD_RST

SMARTCARD_CLK

SMARTCARD_DATA

SMARTCARD_DET

+3.3V_NORMAL

R140

4.7K

MTK_DVB_T2_TUNER

R106

4.7K

MTK_Int_FRC/URSA5

R135

4.7K

MTK_CP_BOX

R101

4.7K

MTK_FRC3/URSA5

R189

4.7K

MTK_EPI

R186

4.7K

MTK_DVB_C2_TUNER

R125

4.7K

MTK_OPTIC_Tx_IC

R130

4.7K

MTK_3D_DEPTH_IC

R108

4.7K

MTK_FHD

R175

4.7K

MTK_DVB_S_TUNER

R132

4.7K

MTK_DDR_768MB

R190

4.7K

MTK_NON_EPI

R127

4.7K

MTK_NON_OPTIC_Tx_IC

R133

4.7K

MTK_DDR_DEFAULT

R129

4.7K

MTK_NON_3D_DEPTH_IC

R141

4.7K

MTK_NON_DVB_T2_TUNER

R102

4.7K

MTK_NO_FRC/Int_FRC

R138

4.7K

MTK_NON_CP_BOX

R109

4.7K

MTK_HD

R187

4.7K

MTK_NON_DVB_C2_TUNER

R184

4.7K

MTK_NON_DVB_S_TUNER

R107

4.7K

MTK_NO_FRC/FRC3

EPI_LOCK6

OPCTRL_0_SDA

OPCTRL_10_SDA

OPCTRL_1_SCL

OPCTRL_11_SCL

OPCTRL_0_SDA

OPCTRL_10_SDA

C1010.1uF16V

R191 22

+3.3V_NORMAL

R192 22

I2C_SCL1

R181 4.7K

I2C_SDA1

+3.3V_NORMAL

MDS62110213

M100

MTK_H/S_3.5T

MDS62110213

M101

MTK_H/S_3.5T

MDS62110213

M102

MTK_H/S_3.5T

MDS62110213

M103

MTK_H/S_3.5T

+3.3V_NORMAL

R159 4.7K

P10012507WS-12L

MTK_JTAG

1

2

3

4

5

6

7

8

9

10

11

12

13

C1202.2uF10VOPT

R193 10K

NON_EU

OPC_EN

/S2_RESET

R1281.2K

R1311.2K

EMMC_DATA[0]

EMMC_DATA[1]

EMMC_CMD

R119

0

IC104-*1M24256-BRMN6TP

NVRAM_ST

3E2

2E1

4VSS

1E0

5SDA

6SCL

7WC

8VCC

C11524pF

C11324pF

AMP_RESET_SOC AMP_RESET_NR124

33

AMP_RESET_BY_SOC

AMP_RESET_SOC

IC105LGE2112

MT5369_NON_RM

JTCKAP14

JTDIAM14

JTDOAR14

JTMSAR15

JTRSTAN14

OSDA0AP12

OSCL0AN12

OSDA1AP15

OSCL1AN15

XTALIAT34

XTALOAU34

AVDD33_XTAL_STBAK27

AVSS33_XTAL_STBAH26

AVDD33_VGA_STBAK18

AVSS33_VGA_STBAK17

AVDD33_PLLGPAK23

AVSS33_PLLGPAM27

AVDD10_LDOAJ20

GPIO0H32

GPIO1F37

GPIO2F36

GPIO3G37

GPIO4G36

GPIO5G35

GPIO6G34

GPIO7H34

GPIO8L34

GPIO9L32

GPIO10K33

GPIO11K32

GPIO12H33

GPIO13L35

GPIO14K36

GPIO15J32

GPIO16J34

GPIO17K34

GPIO18K35

GPIO19K37

GPIO20J36

GPIO21J37

GPIO22J35

GPIO23J33

GPIO24G33

GPIO25H35

GPIO26H31

GPIO27F34

GPIO28E36

GPIO29N33

GPIO30P32

GPIO31M35

GPIO32M37

GPIO33M33

GPIO34F35

GPIO35E35

GPIO36E37

GPIO37N32

GPIO38M34

GPIO39M36

GPIO40M32

GPIO41L33

GPIO42E33

GPIO43E32

GPIO44F32

GPIO45A29

GPIO46D31

GPIO47C31

GPIO48E30

GPIO49E31

GPIO50F31

GPIO51E29

GPIO52AP9

GPIO53AT9

GPIO54AR9

GPIO55AU9

ADIN0_SRVAN23

ADIN1_SRVAN24

ADIN2_SRVAP23

ADIN3_SRVAR23

ADIN4_SRVAU23

ADIN5_SRVAT23

ADIN6_SRVAM24

ADIN7_SRVAM23

U0TXAR18

U0RXAP18

U1RXAU16

U1TXAT16

POWEA35

POOEC33

POCE1B34

POCE0D33

PDD7D29

PDD6C30

PDD5D30

PDD4B31

PDD3A31

PDD2B32

PDD1A32

PDD0C32

PARBD32

PACLEA34

PAALEC34

EMMC_CLKC29

OPWRSBAM20

ORESETAM22

OIRIAU21

FSRC_WRD27

STB_SCLAT21

STB_SDAAR21

DEMOD_RSTT34

DEMOD_TSCLKT32

DEMOD_TSDATA0T36

DEMOD_TSDATA1U36

DEMOD_TSDATA2T33

DEMOD_TSDATA3T30

DEMOD_TSDATA4V33

DEMOD_TSDATA5V32

DEMOD_TSDATA6V31

DEMOD_TSDATA7V30

DEMOD_TSSYNCT35

DEMOD_TSVALT31

CI_INTN36

CI_TSCLKT37

CI_TSDATA0R35

CI_TSSYNCR37

CI_TSVALR36

PVR_TSCLKR34

PVR_TSVALR32

PVR_TSSYNCR33

PVR_TSDATA0P33

PVR_TSDATA1P34

SPI_CLK1N37

SPI_CLKP35

SPI_DATAN34

SPI_CLEN35

OPWM2AU12

OPWM1AT12

OPWM0AR12

SD_D0A37

SD_D1C35

SD_D2A36

SD_D3B35

SD_CMDB36

SD_CLKB37

LDM_CSAT11

LDM_CLKAU11

LDM_VSYNCAR10

LDM_DOAM9

LDM_DIAP10

LED_PWM1AN22

LED_PWM0AP21

OPCTRL11AU20

OPCTRL10AT20

OPCTRL9AN18

OPCTRL8AP20

OPCTRL7AM18

OPCTRL6AN19

OPCTRL5AP19

OPCTRL4AR19

OPCTRL3AN21

OPCTRL2AM19

OPCTRL1AN20

OPCTRL0AR20

IC104-*2R1EX24256BSAS0A

NVRAM_RENESAS

3A2

2A1

4VSS

1A0

5SDA

6SCL

7WP

8VCC

R10010K

AMP_RESET_BY_SOC

C1140.1uF16V

C1050.1uF

OPT

C1060.1uFOPT

C1000.1uF

OPT

C1030.1uF

OPT

C1020.1uF

OPT

C1040.1uFOPT

R1201K

PWM1_PULL_DOWN_1K

R1261K

PWM2_PULL_DOWN_1K

MDS61887710

M104

MTK_H/S_9.5T

IC100M24C16-R

HDCP_EEPROM_ST

3NC_3

2NC_2

4VSS

1NC_1

5 SDA

6 SCL

7 WC

8 VCC

IC100-*124LC16B

HDCP_EEPROM_MICRO

3A2

2A1

4VSS

1A0

5 SDA

6 SCL

7 WP

8 VCC

R105

4.7KOPT

R104

4.7KOPT

M_RFModule_ISP

C1082.2uF10V

C1072.2uF10V

IC105-*1LGE2112-AL

MT5369_RM

DDRV_44AC1

DDRV_45AC2

DDRV_1A3

DDRV_2A4

DDRV_5B4

DDRV_8C4

DDRV_10D4

DDRV_4B3

DDRV_7C3

DDRV_46AC3

DDRV_47AC4

MEMTPG10

MEMTNG9

RVREF_BG13

RVREF_AG21

ARCKEF10

ARCLK1D9

ARCLK1C9

ARCLK0A20

ARCLK0A21

ARODTE18

ARRASF17

ARCASE17

ARCSE16

ARWED14

ARRESETB14

ARBA0A13

ARBA1G11

ARBA2D16

ARCSXF18

ARA14C15

ARA13A15

ARA12F13

ARA11C14

ARA10F11

ARA9E15

ARA8D13

ARA7B15

ARA6E14

ARA5F16

ARA4E13

ARA3B13

ARA2A14

ARA1F14

ARA0F15

ARDQM0C19

ARDQS0C21

ARDQS0B21

ARDQ0C23

ARDQ1B17

ARDQ2D23

ARDQ3C17

ARDQ4D24

ARDQ5C16

ARDQ6C24

ARDQ7D15

ARDQM1D21

ARDQS1B20

ARDQS1C20

ARDQ8A17

ARDQ9A23

ARDQ10D17

ARDQ11B23

ARDQ12D20

ARDQ13D22

ARDQ14D19

ARDQ15C22

ARDQM2A7

ARDQS2B9

ARDQS2A9

ARDQ16C12

ARDQ17D6

ARDQ18B12

ARDQ19C5

ARDQ20C13

ARDQ21A5

ARDQ22A12

ARDQ23B5

ARDQM3E10

ARDQS3C8

ARDQS3D8

ARDQ24C6

ARDQ25D10

ARDQ26D7

ARDQ27C11

ARDQ28C7

ARDQ29C10

ARDQ30B7

ARDQ31B10

AVDD33_MEMPLLN14

AVSS33_MEMPLLN15

DVSS_50R1

DVSS_48P21

8

MID_MAIN_1 2011.12.13

LG FRC2

3D DEPTH

T2 Tuner

MODEL OPTION 8 is just for CP BoxIt should not be appiled at MP

NON_3D_Depth_IC

S Tuner

SoCinternalFRC

SOC -> CI SLOT

NON_OPTIC

CI SLOT -> SOC

SOC -> CI SLOT

MODEL_OPT_9

OPTIC

1

MODEL_OPT_7

MODEL_OPT_3

Support

FHD

Write Protection

- Low : Normal Operation- High : Write Protection

Disable

Reserved

DDR_768MB

EPI

Reserved

MODEL_OPT_2

DDR

MODEL_OPT_6

HIGH

MODEL_OPT_8

CI SLOT -> SOC

MODEL_OPT_0

Not Support

Default

1

Not Support

CP BOX

MODEL_OPT_5

0

0

CI SLOT -> SOC

Support

Enable

LOW

1

NO_FRC

NVRAM

Model Option

0

Close to eMMC Flash(IC8100)

MODEL_OPT_10

0

CI SLOT -> SOC

HD

STRAPPING LED_PWM0 LED_PWM1 OPCTRL3

ICE mode + 27M + Serial boot 0 0 0

ICE mode + 27M + ROM to Nand boot 0 0 1

ICE mode + 27M + Rom to eMMC boot 0 1 0 from eMMC pins (share pins w/s NAND)

ICE mode + 27M + ROM to eMMC boot 0 1 1 from SDIO pins

DDR_Default

EXTERNAL DEMOD-> SOC

MODEL_OPT_1 1

MODEL_OPT_4 3D_Depth_IC

X-TAL

JTAG

I2C

I2C_1 : AMP, L/DIMMING,HDCP KEYI2C_2 : T-CONI2C_3 : MICOMI2C_4 : S/Demod,T2/Demod, LNBI2C_5 : NVRAMI2C_6 : TUNER_MOPLL(T/C,ATV)

FOR JAPAN

FOR JAPAN

HDCP EEPROM

Support Not Support

HEAT SINK SMD GASKET

5V Tolerance

MODEL_OPT_4

MODEL_OPT_4

Crystal Matching Test result: 27pF -> 20pF -> 24pF

IC

EAX6430790* : LD22* / LC22*EAX6443420* : LT22* / LJ22* / LA22* / LB22*

MODEL_OPT_7

MODEL_OPT_7

Copyright © 2012 LG Electronics. Inc. All rights reserved. Only for training and service purposes

LGE Internal Use Only


CI_ADDR[3]

CI_DATA[7]

CI_ADDR[4]

CI_DATA[2]

MT5369_TS_OUT[1]

CI_ADDR[7]

CI_ADDR[8]

CI_ADDR[10]

CI_ADDR[14]

CI_DATA[5]

MT5369_TS_OUT[6]

CI_DATA[6]

MT5369_TS_OUT[4]

CI_DATA[3]

CI_ADDR[12]

MT5369_TS_OUT[7]

CI_ADDR[0]

CI_ADDR[5]

MT5369_TS_OUT[2]

CI_ADDR[11]

MT5369_TS_OUT[5]

CI_DATA[0]

CI_ADDR[1]

CI_DATA[1]

CI_DATA[4]

CI_ADDR[13]

CI_ADDR[6]

MT5369_TS_OUT[0]

CI_ADDR[2]

MT5369_TS_OUT[3]

CI_ADDR[9]

C3230.1uF

MT5369_TS_IN[0]

TP324

C343100pF50V

C3690.01uF

HDMI_HPD_3_JACK

TP337

AV1_R_IN_SOC

D0+_HDMI2_JACK

TXA4P

TP353

COMP1_Pr_SOC

R3791.2K

TP321

R358100

SCART_Rout_SOC

TP345

C3550.047uFT/C&AT&CHB

DTV/MNT_V_OUT_SOC

C3740.01uF

R323 22

TP378

C3971200pF

C359 0.047uF

TP374

TXD1P

C3981200pF

R33075

1%

C3820.1uF

C3540.1uF

/PCM_WE

MT5369_TS_IN[5]

TP375

R311 30K

HP_LOUT_AMP

VDD3V3

TXCCLKP

HP_ROUT_AMP

MT5369_TS_IN[4]

HDMI_HPD_2_JACK

TP372

TXA0N

D2+_HDMI3_JACK

HP_ROUT_MAIN

TP326

C3070.1uF

C336 1uF10V

T/C&AT&CHB

R3730

C38410pF50V

TXDCLKN

IF_AGC

C361 1uF

CK+_HDMI4_JACK

TXD0P

R3781.2K

VDD3V3

SC_R_SOC

R3521.2K

HP_OUT

D2-_HDMI3_JACK

TXC1P

PC_R_IN_SOC

C3800.1uF

DSUB_VSYNC

TXD2N

TP322

TP307

TXB2P

C4001200pF

TP350

PC_L_IN_SOC

+1.2V_MTK_AVDD

C3710.01uF

AV1_CVBS_IN_SOC

TXC1N

TP329

+1.2V_MTK_AVDD

R341 100

R309100K

TXD0N

PC_R_IN

EPHY_TDP

C39127pF50VOPT

TP311

R371 100

D2-_HDMI4_JACK

R310 30K

TP318

SCART_Rout_SOC

C38627pF50VOPT

TXB1P

DSUB_HSYNC_SOC

AUD_LRCH

R300

470K

OPT

DDC_SDA_1_SOC

TP313

TXC2N

TP348

C3320.22uF10V

HP_OUT

C3660.01uF

TXC0P

SC_B_SOC

CK-_HDMI2_JACK

OSCL2

OSDA2

D1-_HDMI2_JACK

C3020.1uF

R35475

1%

DSUB_VSYNC_SOC

C39227pF50VOPT

C3951200pF

HP_OUT

DDC_SCL_4_JACK

R335 51

T/C&AT&CHB

TXDCLKP

TXA1P

EPHY_RDP

TP365

DAC_3V3

C38527pF50VOPT

PC_L_IN_SOC

SCART_Lout_SOC

5V_HDMI_2_JACK

R368 100

AV1_L_IN_SOC

TP355

+1.2V_MTK_AVDD

C3310.22uF10V

HP_OUT

C3831200pFHP_OUT

TP300

D1+_HDMI3_JACK

R3701.2K

HP_OUT

SC_G_SOC

TP341

D0-_HDMI1_SOC

DDC_SCL_2_JACK

R34324K

1%

VDD3V3

VDD3V3

SC_G_SOC

TP370

AV1_R_IN

C3410.047uFT/C&AT&CHB

TP308C39322pFOPT

D0+_HDMI1_SOC

R367 100

C38722pF

OPT

TXA4N

VDD3V3

R3720

TP330

C3080.1uF

TP351

TP366

/CI_CD1

C31910uF16V

R362100

TP360

TXD3P

D0+_HDMI4_JACK

TP334

MT5369_MISTRT

C3701500pF

R301470KOPT

D1+_HDMI1_SOC

D2+_HDMI2_JACK

C314100pF50V

OPT

COMP1_Pr_SOC

TXB1N

SC_L_IN_SOC

C34047pF50V

C3640.1uF

ARC

TP317

SC_DET

C34427pF50VOPT

TXA3N

C300560pF50V

OPT

SPDIF_OUT

TP359

C301560pF50V

OPT

D0-_HDMI4_JACK

C3510.1uF

IF_P

TU_CVBS

WIFI_DM

TXD4N

R334 51

T/C&AT&CHB

R3500

R357100

TXA1N

TXACLKP

TXC0N

L303BLM18PG121SN1D

HP_OUT

TUNER_SIF

TP338

/PCM_IRQA

MT5369_MIVAL_ERR

SC_R_SOC

TP320

DDC_SCL_3_JACK

R324 22

C3160.1uF

TP373

R3511.2KHP_OUT

MT5369_TS_IN[6]

MT5369_TS_IN[7]

C337 1uF

10VT/C&AT&CHB

/PCM_REG

TP352

VDD3V3

HDMI_HPD_1_SOC

EPHY_RDN

WIFI_DP

C3720.01uF

C3730.01uF

R3081.2KOPT

R366 100

+1.2V_MTK_AVDD

TXA2P

C3670.01uF

D2-_HDMI2_JACK

DSUB_G+

R328

470K

OPT

TP314

DDC_SDA_2_JACK

D1+_HDMI4_JACK

+1.2V_MTK_AVDD

TP335

VDD3V3

C3991200pF

L302BLM18PG121SN1D

HP_OUT

D2+_HDMI1_SOC

R35375

1%

AUDIO_R_OUT_COMMERCIAL

TP356

PCM_5V_CTL

TP336

R31524K

D1+_HDMI2_JACK

MT5369_TS_SYNC

TP328

R32275

HP_ROUT

MT5369_MCLKI

TP310

R361100

MT5369_TS_VAL

C32010uF16V

TP342

CK+_HDMI3_JACK

RGB_DDC_SDA

TXB0N

C3901200pFHP_OUT

VDD3V3

R35575

1%

AUD_LRCK TP358

HP_LOUT_MAIN

TXC2P

TXB4P

C377

1200pFHP_OUT

C3680.01uF

TP346

TXB4N

C3295pF50VOPT

EPHY_TDN

TP312

AUD_MASTER_CLK

TXD2P

/PCM_IORD

MT5369_TS_CLK

TP343

TP362

TXACLKN

D2+_HDMI4_JACK

/PCM_CE1

COMP1_Pb_SOC

MT5369_TS_IN[2]

PC_L_IN

R32175

MT5369_TS_IN[1]

R32075

TP349

TXA2N

R307 1K

C39427pF50VOPT

C3040.1uF

DTV/MNT_V_OUT_SOC

R329470KOPT

TXCCLKN

TP319

SC_COM_SOC

HDMI_ARC

AV1_R_IN_SOC

R3392.2KOPT

AV1_CVBS_IN_SOC

C38827pF50VOPT

HDMI_HPD_4_JACK

R3761.2K

CK-_HDMI4_JACK

D1-_HDMI4_JACK

TP347

CK-_HDMI3_JACK

D0+_HDMI3_JACK

TXB3P

SC_FB_SOC

COMP1_Y_SOC

D1-_HDMI1_SOC

TXB0P

R356100

5V_HDMI_4_JACK

C38922pF

OPT

CK-_HDMI1_SOC

R3740

COMP1_Pr

TP377

R3771.2K

C34610uF16V

C360 0.047uF

R305 1K

TP367

TP323

C3631uF25V

AV1_L_IN

/PCM_OE

TXD3N

C315100pF50V

OPT

R3691.2KHP_OUT

5V_HDMI_3_JACK

TP331

SC_R_IN_SOC

R3262K

OPT

SC_CVBS_IN_SOC

VDD3V3

C3280.1uF

SC_COM_SOC

SC_ID_SOC

SC_L_IN_SOC

RGB_DDC_SCL

CK+_HDMI1_SOC

CI_DATA[0-7]

C3305pF50VOPT

C3580.01uF

50V

MT5369_TS_OUT[0-7]

TP316

D0-_HDMI2_JACK

C34510uF16V

CK+_HDMI2_JACK

DDC_SDA_4_JACK

ARC

COMP1_Pb

C3030.1uF

AV1_CVBS_IN

C3751500pF

R340 100

TP339

SC_FB_SOC

IF_N

R342 10KT/C&AT&CHB

SC_CVBS_IN_SOC

TXC4N

TP371

R359100

C37910pF50V

DDC_SDA_3_JACK

+1.2V_MTK_AVDD

TXA0P

DDC_SCL_1_SOC

DSUB_HSYNC

TXC4P

C37810pF50V

TP340

COMP1_Y_SOC

R332 10KT/C&AT&CHB

C3470.1uF

AUD_SCK

SC_R_IN_SOC

TP357

C338560pF50V

OPT

TP325

PCM_RST

D2-_HDMI1_SOC

D1-_HDMI3_JACK

/PCM_IOWR

SC_B_SOC

TP363

R306 1K

DSUB_VSYNC_SOC

SCART_Lout_SOC

R304 1K

TXC3P

CI_ADDR[0-14]

R30382

TP315

TP309

TP332

AV1_L_IN_SOC

D0-_HDMI3_JACK

/PCM_WAIT

AUDIO_L_OUT_COMMERCIAL

R363100

5V_HDMI_1_SOC

TP368

TXBCLKN

TXBCLKP

COMP1_Y

TP344

TP361

R3490OPT

HP_LOUT

CI_A_VS1

DSUB_R+

COMP1_Pb_SOC

/CI_CD2

TP327

TP364

TP369

TXA3P

TXB2N

TXB3N

C342100pF50V

TP333

MT5369_TS_IN[3]

C339560pF50V

OPT

R3252K

OPT

R302180

C352 0.01uF

TXC3N

PC_R_IN_SOC

DSUB_B+

R364100

DSUB_HSYNC_SOC

TXD4P

TP354

C39633pF

OPT

+5V_NORMAL

TXD1N

C3060.1uF

MODEL_OPT_10

2D/3D_CTL

MODEL_OPT_2

PCM_5V_CTL

EMMC_RST

MODEL_OPT_8

MODEL_OPT_9

VCOM_DYN

GST_SOC

MCLK_SOC

GCLK_SOC

EO_SOC

PMIC_RESET

C3650.01uF

C3051uF25V

C3620.1uF

C350

0.1uF

R314

0

R336

0

R331 0

T/C&AT&CHB

R346 0T/C&AT&CHB

C309OPT

C311 1uF

10V

C310

33pFT/C&AT&CHB

C312

33pF

T/C&AT&CHB

C33447pF50V

C33547pF50V

C33347pF50V

USB_DP2

USB_DM2

USB_DP1

USB_DM1

USB_DM3

USB_DP3

IC105LGE2112

HDMI_CECAA32

HDMI_0_SCLAG33

HDMI_1_SCLAE33

HDMI_2_SCLAC33

HDMI_3_SCLAH32

HDMI_0_SDAAF33

HDMI_1_SDAAD33

HDMI_2_SDAAB33

HDMI_3_SDAAH33

HDMI_0_PWR5VAG31

HDMI_1_PWR5VAE31

HDMI_2_PWR5VAC31

HDMI_3_PWR5VAH31

HDMI_0_HPDAG32

HDMI_1_HPDAE32

HDMI_2_HPDAC32

HDMI_3_HPDAJ32

AVDD12_HDMI_0_RXAA24

AVDD12_HDMI_1_RXY24

AVDD12_HDMI_2_RXW24

AVDD12_HDMI_3_RXAB24

AVDD33_HDMI_0_RXAB29

AVDD33_HDMI_1_RXAA29

AVDD33_HDMI_2_RXY29

AVDD33_HDMI_3_RXAC29

AVSS33_HDMI_RX_1AB30

AVSS33_HDMI_RX_2AD30

AVSS33_HDMI_RX_3AF31

AVSS33_HDMI_RX_4AF32

USB_DP_P0C36

USB_DM_P0C37

USB_DP_P1D36

USB_DM_P1D37

USB_DP_P2AT13

USB_DM_P2AU13

USB_DP_P3AT14

USB_DM_P3AU14

AVDD33_USB_P0P1D35

AVDD33_USB_P2P3AP13

AVSS33_USB_P1D34

AVSS33_USB_P2AR13

PCIE11_TXPW35

PCIE11_TXNW34

PCIE11_RXNY34

PCIE11_RXPY35

AVDD12_PCIE11U24

AVDD33_PCIE11V24

AVSS12_PCIE11W30

PCIE11_REFCKNW36

PCIE11_REFCKPW37

HDMI_0_RX_0AG35

HDMI_0_RX_0BAG34

HDMI_0_RX_1AG37

HDMI_0_RX_1BAG36

HDMI_0_RX_2AF35

HDMI_0_RX_2BAF34

HDMI_0_RX_CAH35

HDMI_0_RX_CBAH34

HDMI_1_RX_0AE37

HDMI_1_RX_0BAE36

HDMI_1_RX_1AD35

HDMI_1_RX_1BAD34

HDMI_1_RX_2AC35

HDMI_1_RX_2BAC34

HDMI_1_RX_CAE35

HDMI_1_RX_CBAE34

HDMI_2_RX_0AB35

HDMI_2_RX_0BAB34

HDMI_2_RX_1AA35

HDMI_2_RX_1BAA34

HDMI_2_RX_2AA37

HDMI_2_RX_2BAA36

HDMI_2_RX_CAC37

HDMI_2_RX_CBAC36

HDMI_3_RX_0AK35

HDMI_3_RX_0BAK34

HDMI_3_RX_1AJ35

HDMI_3_RX_1BAJ34

HDMI_3_RX_2AJ37

HDMI_3_RX_2BAJ36

HDMI_3_RX_CAJ33

HDMI_3_RX_CBAK33

TXVP_0AT18

TXVN_0AU18

RXVN_1AU17

RXVP_1AT17

PHYLED1AN16

PHYLED0AM16

REXTAD15

AVDD12_RECAD14

AVDD33_COMAD16

AVDD33_LDAD17

AVSS33_LDAL16

AVSS33_COMAL15

AVSS12_RECAL14

IC105LGE2112

TCON0F27

TCON1E27

TCON2F30

TCON3F29

TCON4B27

TCON5A27

TCON6B28

TCON7A28

TCON8C28

TCON9D28

TCON10E28

TCON11F28

TCON12B29

AVDD12_LVDS_1AG6

AVDD12_LVDS_2AJ6

AVDD12_VPLLAF6

AVDD33_LVDSBAE6

AVDD33_LVDSAAH7

AVSS12_LVDS_2AJ5

AVSS12_LVDS_1AG5

AVSS12_VPLLAF5

AVSS33_LVDSBAE5

AVSS33_LVDSAAH5

REXT_VPLLAG7

AIN0_R_AADCAU37

AIN0_L_AADCAU35

AIN1_R_AADCAT35

AIN1_L_AADCAT37

AIN2_R_AADCAU36

AIN2_L_AADCAP34

AIN3_R_AADCAT36

AIN3_L_AADCAR37

AIN4_R_AADCAR33

AIN4_L_AADCAP32

AIN5_R_AADCAR36

AIN5_L_AADCAP37

AIN6_R_AADCAR35

AIN6_L_AADCAP36

AVDD33_AADCAL31

AVSS33_AADCAJ28

VMID_AADCAJ27

MPXPAN28

ADCINP_DEMODAU32

ADCINN_DEMODAT32

AVDD33_DEMODAD22

AVDD12_DEMODAL27

AVSS33_DEMODAM28

AVSS12_DEMODAJ26

IF_AGCU35

RF_AGCU34

LOUTNAP31

LOUTPAN30

OSCL2V35

OSDA2V34

SC0AP28

SY0AR29

CVBS3PAT30

CVBS2PAR30

CVBS1PAR31

CVBS0PAN29

CVBS_COMAP30

AVDD33_CVBS_1AK24

AVDD33_CVBS_2AK25

AVSS33_CVBS_1AL25

AVSS33_CVBS_2AM26

AO3NAG3

AO3PAG4

AO4NAG1

AO4PAG2

AOCLKNAF3

AOCLKPAF4

AO2NAE3

AO2PAE4

AO1NAE1

AO1PAE2

AO0NAD1

AO0PAD2

AE4NAL3

AE4PAL4

AE3NAL1

AE3PAL2

AECLKNAK3

AECLKPAK4

AE2NAJ3

AE2PAJ4

AE1NAJ1

AE1PAJ2

AE0NAH3

AE0PAH4

BO4NAT2

BO4PAU2

BO3NAT1

BO3PAU1

BOCLKNAR1

BOCLKPAR2

BO2NAP1

BO2PAP2

BO1NAN1

BO1PAN2

BO0NAM3

BO0PAM4

BE4NAT6

BE4PAU6

BE3NAP6

BE3PAR6

BECLKNAP5

BECLKPAR5

BE2NAT4

BE2PAU4

BE1NAP4

BE1PAR4

BE0NAP3

BE0PAR3

AR0_ADACAN35

AL0_ADACAN34

AR1_ADACAM32

AL1_ADACAM34

AR2_ADACAM37

AL2_ADACAM33

AR3_ADACAM36

AL3_ADACAM35

AVDD33_DACAG30

AVDD33_DAC1AF30

AVSS33_DACAK30

AVSS33_DAC1AE30

ALINY33

ASPDIF0AR16

ASPDIF1Y32

AOBCKAR11

AOLRCKAP11

AOMCLKAM12

AOSDATA4AM10

AOSDATA3AM11

AOSDATA2AN11

AOSDATA1AN10

AOSDATA0AN9

HSYNCAN25

VSYNCAM25

RPAR25

GPAR24

BPAU24

COMAP24

SOGAT24

VGA_SDAAR22

VGA_SCLAP22

COM1AT26

PB1PAR26

PR1PAP26

Y1PAU26

SOY1AP25

COM0AU28

PB0PAT28

PR0PAR28

Y0PAP27

SOY0AR27

VDACX_OUTAU30

VDACY_OUTAP29

AVDD33_VDAC_BGAD20

AVDD33_VDACAD21

AVDD12_RGBAD19

AVSS33_VDAC_BGAJ22

AVSS12_RGBAJ21

AVSS33_VDACAL24

L301

BLM15BD121SN1

L300

BLM15BD121SN1

L304

BLM15BD121SN1

ZD3045.48VTO5.76V

ZD3055.48VTO5.76V

ZD306

5.48VTO5.76V

ZD307

5.48VTO5.76V

ZD302

5.48VTO5.76V

ZD300

5.48VTO5.76V

ZD303

5.48VTO5.76V

ZD301

5.48VTO5.76V

D300

5.5VADLC 5S 02 015

D302

5.5VADLC 5S 02 015

D301

5.5VADLC 5S 02 015

R344

30K

R345

30K

C348100pF50V

R338 0

R337 0

R333

120-ohm

9

MID_MAIN_2 2011.12.19

Close to MT5369

Place at JACK SIDE

1608 sizs For EMI

PLACE AT JACK SIDE

Close to Tuner

1.0Vpp

Close to Tuner

CHANGE SYMBOL

1608 sizs For EMI

1608 sizs For EMI

Don’t use as GPIO

FOR EMI

CH1

CH2

CH3

CH4

CH5

CH6

1608 sizs For EMI

1608 sizs For EMI

1608 sizs For EMI

1608 sizs For EMI

For PCB Pattern

For PCB Pattern

For PCB Pattern

For PCB Pattern

Close to MT5369

Port was changed !!!!

PLACE AT JACK SIDE

1608 sizs For EMI




C5320.1uF

+3.3V_NORMAL

POWER_ON/OFF1

C5440.1uF16V

C5350.1uFC503

10uF

C53910uF

+1.2V_MTK_CORE

EMMC_VCCQ

C5500.1uF

C52510uF

+1.2V_MTK_CORE

C5290.1uF

+1.2V_MTK_CORE

TP500

3.3V_EMMC

R5001

C5120.1uF16V

C5460.1uF

C54010uF10V

TP501

C5430.1uF

L500BLM18PG121SN1D

DAC_3V3

LAN_JACK_POWER

+3.3V_NORMAL

L504BLM18PG121SN1D

+3.3V_NORMAL

VDD3V3

C5480.1uF

C50010uF

C5100.1uF

+1.2V_MTK_CORE

VDD3V3

C5220.1uF16V

C52610uF10V

L506BLM18PG121SN1D

+5V_NORMAL

C5520.1uF

C5530.1uF

VDD3V3

L501BLM18PG121SN1D

C5010.1uF

AVDD_33SB

L502BLM18PG121SN1D

C5020.1uF

+1.2V_MTK_CORE +1.2V_MTK_AVDD

C50510uF

C50610uF

+1.2V_MTK_CORE

+1.5V_DDR

IC501AP1117E33G-13

OUT

INADJ/GND

C52410uF

IC105LGE2112

DVSS_51R2

DVSS_52R3

DVSS_37J4

DVSS_53R4

DVSS_107Y4

DVSS_20F5

DVSS_38J5

DVSS_54R5

DVSS_108Y5

DVSS_95W5

DVSS_44L7

DVSS_46M7

DVSS_56R7

DVSS_120AA5

DVSS_130AB5

DVSS_43K7

DVSS_77U7

DVSS_97W7

DVSS_13E9

DVSS_12E8

DVSS_22F9

DVSS_28G14

DVSS_39J6

DVSS_57R15

DVSS_68T15

DVSS_78U15

DVSS_87V15

DVSS_99W15

DVSS_112Y15

DVSS_122AA15

DVSS_132AB15

DVSS_34H11

DVSS_58R16

DVSS_69T16

DVSS_79U16

DVSS_88V16

DVSS_100W16

DVSS_113Y16

DVSS_123AA16

DVSS_133AB16

DVSS_59R17

DVSS_70T17

DVSS_80U17

DVSS_89V17

DVSS_114Y17

DVSS_71T18

DVSS_90V18

DVSS_115Y18

DVSS_72T19

DVSS_91V19

DVSS_116Y19

DVSS_101W17

DVSS_124AA17

DVSS_134AB17

DVSS_60R18

DVSS_131AB6

DVSS_35H19

DVSS_36H22

DVSS_40J11

DVSS_41J12

DVSS_42J22

DVSS_55R6

DVSS_62R20

DVSS_73T20

DVSS_83U20

DVSS_92V20

DVSS_104W20

DVSS_117Y20

DVSS_127AA20

DVSS_137AB20

DVSS_29G16

DVSS_63R21

DVSS_74T21

DVSS_84U21

DVSS_93V21

DVSS_105W21

DVSS_118Y21

DVSS_128AA21

DVSS_138AB21

DVSS_64R22

DVSS_75T22

DVSS_85U22

DVSS_94V22

DVSS_106W22

DVSS_119Y22

DVSS_129AA22

DVSS_139AB22

DVSS_65R23

DVSS_76T23

DVSS_86U23

DVSS_140AB23

DVSS_96W6

DVSS_30G17

DVSS_27F25

DVSS_109Y6

DVSS_17E21

DVSS_25F21

DVSS_45L8

DVSS_66T7

DVSS_7D11

DVSS_14E11

DVSS_8D12

DVSS_18E22

DVSS_26F22

DVSS_33G25

DVSS_136AB19

DVSS_126AA19

DVSS_49P22

DVSS_103W19

DVSS_82U19

DVSS_61R19

DVSS_110Y7

DVSS_135AB18

DVSS_125AA18

DVSS_102W18

DVSS_81U18

DVSS_121AA7

DVSS_47N22

DVSS_67T8

DVSS_98W8

DVSS_111Y8

DVSS_11E7

DVSS_21F8

IC105LGE2112

VCCK_43AR7

VCCK_45AT7

VCCK_47AU7

VCCK_42AP8

VCCK_44AR8

VCCK_46AT8

VCCK_48AU8

VCCK_37AM7

VCCK_39AN7

VCCK_41AP7

VCCK_38AM8

VCCK_40AN8

VCCK_1P14

VCCK_9R14

VCCK_11T14

VCCK_13U14

VCCK_14V14

VCCK_16W14

VCCK_18Y14

VCCK_20AA14

VCCK_22AB14

VCCK_23AC14

VCCK_28AC19

VCCK_2P15

VCCK_24AC15

VCCK_3P16

VCCK_25AC16

VCCK_15V23

VCCK_17W23

VCCK_19Y23

VCCK_21AA23

VCCK_31AC22

VCCK_32AC23

VCCK_36AD24

VCCK_8P23

VCCK_10R24

VCCK_12T24

VCCK_33AC24

VCCK_30AC21

VCCK_7P20

VCCK_29AC20

VCCK_6P19

VCCK_27AC18

VCCK_5P18

VCCK_26AC17

VCCK_4P17

VCCK_34AD18

VCCK_35AD23

VCC3IO_B_4AL9

VCC3IO_B_2AK10

VCC3IO_B_1AK9

VCC3IO_B_3AK11

VCC3IO_A_5H29

VCC3IO_A_7J29

VCC3IO_A_6H30

VCC3IO_A_8J30

VCC3IO_A_3G31

VCC3IO_A_4G32

VCC3IO_A_2F33

VCC3IO_A_1E34

MDS62110209

M501

SMD_GASKIT_8.5T_RGB

MDS62110209

M500

SMD_GASKIT_8.5T_LAN

MDS62110209

M502

SMD_GASKIT_8.5T_COMP

C5450.1uF

+1.2V_MTK_CORE

C5310.1uF

C5370.1uF

+1.5V_DDR

C5470.1uF

C5330.1uF

C5360.1uF

C5200.1uF

C5270.1uF

C5140.1uF

C5080.1uF

C5230.1uF

MDS62110217

M504

SMD_GASKIT_12.5T_USB1

MDS62110217

M506

SMD_GASKIT_12.5T_HDMI1

MDS62110217

M503

SMD_GASKIT_12.5T_HDMI2

MDS62110217

M505

SMD_GASKIT_12.5T_USB3

C5042.2uF

10

2011.12.09MID_MAIN_3

60mA

5600mA

DECAP FOR SOC (HIDDEN - UCC) DECAP FOR SOC (BOTTOM)

SMD Gaskit

LAN RGB COMP

HDMI2~3HDMI1~2 USB1~2 USB3




SC_FB_SOC

C60510pFEU

C614 0.01uF

EU

R61051K

1/16W1%EU

R607751%EU

SC_FB

SC_B_SOC

C60110pF

OPT

SC_L_IN_SOC

C60610pF

EU

C613 0.01uF

EU

SC_R_IN

SC_CVBS_IN_IF

R615

751%

EU

SC_ID

R617 100

EU

SC_CVBS_IN

SC_G

C615 0.01uF

EU

SCART_Lout

SC_ID_SOC

SC_R_SOC

C60410pF

EU

R604751%EU

R622 100

EUR606751%EU

SC_CVBS_IN_SOCC616 0.047uF

EU

R621 100

EU

R60922EU

SC_R_IN_SOC

R620 100

EU

R61310KEU

R616

751%

EU

SCART_Rout_SOC

SC_B

R601470KOPT

SC_R

SCART_RoutR61815K

EU

DTV/MNT_V_OUT_SOC

R605751%EU

TU_CVBS

R608751%EU

C612 0.01uF

EU

SC_COM_SOC

SC_CVBS_IN_IF

SC_L_IN

SCART_Lout_SOC

R623 100

EU

DTV/MNT_V_OUT

SC_G_SOC

R61915K

EU

R602470KOPT

C61010uF16V

EU

C61110uF16V

EU

C603330pF50VOPT

C602330pF50VOPT

R600EU

0

TP600

C600220pF

OPT

C617220pFOPT

R627330pF50VEU

R603330pF50VEU

+12V

R630100K

OPT

R631100K

OPT

R628100K

OPT

R629100K

OPT

+12V

R632

EU0

R633

EU0

SCART_AMP_R_FB

SCART_AMP_L_FB

R612

EU0

R634

EU0

R6140

1/16W5%EU

R6240

1/16W5%

EU

R62530KEU

R62630KEU

C608100pF50VEU

C609100pF50VEU

C607100pFEU

R611

EU

120-ohm

R635

10KEU

R636

10KEU

2011.12.30

11

MID_MAIN_SCART

PLACE AT MAIN SOC SIDE

PLACE AT JACK SIDE

READY FOR FILTER (EMI)



PLACE AT IC6000




BRDQ[30]

BRDQ[18]

BRA[10]

ARDQ[30]

BRA[1]

BRDQ[22]

BRA[4]

ARDQ[22]

ARDQ[26]

ARA[11]

ARA[0]

BRA[12]

ARA[6]

BRA[10]

BRDQ[28]

BRA[7]

ARDQ[20]

BRA[6]

BRA[5]

BRA[9]

ARA[8]

ARA[5]

ARA[9]

ARA[6]

ARA[5]

ARA[0]

ARDQ[16]

BRA[8]

BRA[11]

ARDQ[28]

ARA[3]

BRA[7]

ARA[7]

ARA[5]

ARA[10]ARA[11]

BRDQ[17]

BRA[1]

BRA[8]

BRA[14]

BRA[13]

ARA[7]

ARDQ[19]

BRA[2]

ARA[0]

ARA[2]

ARA[13]

BRA[5]

ARA[8]

BRA[3]

BRA[11]

BRA[12]

ARA[6]

BRDQ[26]

ARA[13]

ARA[9]

ARDQ[17]

BRDQ[23]

BRA[3]

ARA[1]

ARA[3]

BRA[0]

BRA[11]

ARA[12]ARA[12]

BRA[12]

BRDQ[20]

ARDQ[31]

ARA[4]

BRDQ[31]

BRA[8]

ARA[12]

BRDQ[27]

BRDQ[19]

ARA[10]

ARA[4]

ARA[11]

ARA[2]

ARDQ[27]

ARA[4]

ARA[1]

BRA[0]

BRA[1]

BRA[9]

ARA[3]

ARA[7]

BRA[10]

BRA[2]

BRDQ[21]

BRA[4]

BRA[13]

ARDQ[21]

BRA[7]

ARDQ[29]

ARDQ[18]

BRDQ[25]

BRA[3]

ARA[8]

BRDQ[24]

ARA[9]ARA[10]

BRDQ[29]

ARDQ[24]

BRA[13]

BRA[6]

ARDQ[25]

ARA[13]

BRA[5]

ARDQ[23]

BRA[2]

BRDQ[16]

BRA[0]

BRA[4]

ARA[2]

BRA[6]

ARA[1]

BRA[9]

ARA[14]

BRBA1

+1.5V_DDR

/ARCLK0

ARDQS3

R7162401%

ARDQ[24-31]

TP701

C7250.1uF

ARDQM1

+1.5V_DDR

ARCKE

BRCLK1

/ARDQS0

R7201K1%

ARDQ[8-15]

+1.5V_DDR

BRDQM0

R7141005%

ARBA1

ARDQM3

BRDQS1

/ARDQS2

ARDQM2

R7301K1%

ARBA0

RVREF_D

A_RVREF1

R7091K1%

C7200.1uF

BRDQ[24-31]

R7241K1%

C7260.1uF

ARDQ[0-7]ARDQ[16-23]

BRA[14]

R7291K1%

BRDQS2

R7281K1%

BRDQS3

RVREF_A

ARCLK1

B_RVREF6

BRA[14]

ARCLK0

ARA[0-13]

A_RVREF4

ARDQS1

B_RVREF7

ARBA1

R7151005%

ARODT

C7190.1uF

R7051K1%

BRDQS3

C7540.1uF

BRDQM3

BRDQ[0-7]

BRREST

BRA[0-14]

B_RVREF5

BRDQS0

B_RVREF6

+1.5V_DDR

TP700

ARDQM0

/ARCAS

C7220.1uF

R7061K1%

ARBA2

RVREF_D

ARDQS3

BRDQ[16-23]

ARA[0-13]

/ARCAS

+1.5V_DDR

C7530.1uF

/ARWE

/BRDQS2

ARDQM2

R711 2401%

+1.5V_DDR

/BRCS

+1.5V_DDR

/BRRAS

+1.5V_DDR

RVREF_B

BRBA1

BRBA2

R7321K1%

/BRWE

/ARCLK0

R7331K1%

R7131005%

R7211K1%

R7221K1%

R7261K1%

+1.5V_DDR

+1.5V_DDR

+1.5V_DDR

/BRDQS0

+1.5V_DDR

ARBA1

BRDQM0

C7510.1uF

C7170.1uF

BRDQS0

BRDQM1

BRCLK1

ARDQ[8-15]

ARA[0-14]

BRA[0-13]

C7450.1uF

ARDQS1

ARDQM0

R7271K1%

ARDQ[16-23]

BRBA2

ARREST

+1.5V_DDR

C7570.1uF

/BRDQS1

BRBA0

/BRCAS

+1.5V_DDR

B_RVREF8

RVREF_C

/BRCS

/BRCLK0

BRBA0

BRCLK0

/ARCS

C7520.1uF

/ARCS

/ARDQS0

+1.5V_DDR

B_RVREF5

BRDQM1

ARDQ[24-31]

+1.5V_DDR

BRBA0

/BRCLK0

/BRDQS1

BRDQ[24-31]

BRODT

ARREST

/ARWE

ARDQ[0-7]

+1.5V_DDR

/ARDQS3

/ARDQS1

/BRCLK1

/BRDQS3

ARBA2

BRA[0-13]

A_RVREF1

/ARWE

R7172401%

R7121005%

/ARCLK1

ARDQS2

A_RVREF3

ARCLK1

C7230.1uF

BRDQM3

ARDQS0

ARDQM1

AVDD3V3_MEMPLL

RVREF_C

C7550.1uF

C7270.1uF

+1.5V_DDR

BRDQ[0-7]

+1.5V_DDR

R7231K1%

BRREST

ARBA2

A_RVREF2

R7071K1%

C7210.1uF

R7181K1%

/BRCS

/BRRAS

C7240.1uF

/ARCLK1

/BRCAS

ARCKE

R7311K1%

BRREST

ARCKE

RVREF_B

+1.5V_DDR

B_RVREF8

BRDQ[16-23]

B_RVREF7

ARODT

R7251K1%

/ARDQS2

R7041K1%

/ARRAS

BRODT

BRCKE

BRODT

ARBA0

ARCLK0

C7560.1uF

BRDQ[8-15]

/ARCAS

ARDQM3

BRCKE

ARBA0

+1.5V_DDR

BRDQS1

/BRDQS0

/ARRAS

/BRWE

RVREF_A

ARDQS0

/ARDQS1

R7191K1%

+1.5V_DDR

C7180.1uF

BRDQS2

C7280.1uF

R710 240

1%

/BRWE

/BRCLK1

0.1uFC758

BRBA1

BRDQM2

BRCKE

A_RVREF3

/ARDQS3

/ARRAS

A_RVREF2

ARA[14]

/BRCAS

ARDQS2

ARA[14]

BRCLK0

BRDQ[8-15]

R7081K1%

/BRDQS2

R7031K1%

C7500.1uF

/BRDQS3

BRBA2

R7021K1%

A_RVREF4

+1.5V_DDR

ARREST

BRDQM2

ARODT

/BRRAS

/ARCS

+3.3V_NORMAL

L700BLM18PG121SN1D

AVDD3V3_MEMPLL

C7000.1uF

C70110uF10V

C70410uF10V

C70710uF10V

C70810uF10V

1uFC706

1uFC705

1uFC703

1uFC702

H5TQ2G63BFR-PBCIC703

DDR_HYNIX

A0N3

A1P7

A2P3

A3N2

A4P8

A5P2

A6R8

A7R2

A8T8

A9R3

A10/APL7

A11R7

A12/BCN7

A13T3

A15M7

BA0M2

BA1N8

BA2M3

CKJ7

CKK7

CKEK9

CSL2

ODTK1

RASJ3

CASK3

WEL3

RESETT2

DQSLF3

DQSLG3

DQSUC7

DQSUB7

DMLE7

DMUD3

DQL0E3

DQL1F7

DQL2F2

DQL3F8

DQL4H3

DQL5H8

DQL6G2

DQL7H7

DQU0D7

DQU1C3

DQU2C8

DQU3C2

DQU4A7

DQU5A2

DQU6B8

DQU7A3

VREFCAM8

VREFDQH1

ZQL8

VDD_1B2

VDD_2D9

VDD_3G7

VDD_4K2

VDD_5K8

VDD_6N1

VDD_7N9

VDD_8R1

VDD_9R9

VDDQ_1A1

VDDQ_2A8

VDDQ_3C1

VDDQ_4C9

VDDQ_5D2

VDDQ_6E9

VDDQ_7F1

VDDQ_8H2

VDDQ_9H9

NC_1J1

NC_2J9

NC_3L1

NC_4L9

NC_6T7

VSS_1A9

VSS_2B3

VSS_3E1

VSS_4G8

VSS_5J2

VSS_6J8

VSS_7M1

VSS_8M9

VSS_9P1

VSS_10P9

VSS_11T1

VSS_12T9

VSSQ_1B1

VSSQ_2B9

VSSQ_3D1

VSSQ_4D8

VSSQ_5E2

VSSQ_6E8

VSSQ_7F9

VSSQ_8G1

VSSQ_9G9


DDR_HYNIX

A0N3

A1P7

A2P3

A3N2

A4P8

A5P2

A6R8

A7R2

A8T8

A9R3

A10/APL7

A11R7

A12/BCN7

A13T3

A15M7

BA0M2

BA1N8

BA2M3

CKJ7

CKK7

CKEK9

CSL2

ODTK1

RASJ3

CASK3

WEL3

RESETT2

DQSLF3

DQSLG3

DQSUC7

DQSUB7

DMLE7

DMUD3

DQL0E3

DQL1F7

DQL2F2

DQL3F8

DQL4H3

DQL5H8

DQL6G2

DQL7H7

DQU0D7

DQU1C3

DQU2C8

DQU3C2

DQU4A7

DQU5A2

DQU6B8

DQU7A3

VREFCAM8

VREFDQH1

ZQL8

VDD_1B2

VDD_2D9

VDD_3G7

VDD_4K2

VDD_5K8

VDD_6N1

VDD_7N9

VDD_8R1

VDD_9R9

VDDQ_1A1

VDDQ_2A8

VDDQ_3C1

VDDQ_4C9

VDDQ_5D2

VDDQ_6E9

VDDQ_7F1

VDDQ_8H2

VDDQ_9H9

NC_1J1

NC_2J9

NC_3L1

NC_4L9

NC_6T7

VSS_1A9

VSS_2B3

VSS_3E1

VSS_4G8

VSS_5J2

VSS_6J8

VSS_7M1

VSS_8M9

VSS_9P1

VSS_10P9

VSS_11T1

VSS_12T9

VSSQ_1B1

VSSQ_2B9

VSSQ_3D1

VSSQ_4D8

VSSQ_5E2

VSSQ_6E8

VSSQ_7F9

VSSQ_8G1

VSSQ_9G9


DDR_HYNIX

A0N3

A1P7

A2P3

A3N2

A4P8

A5P2

A6R8

A7R2

A8T8

A9R3

A10/APL7

A11R7

A12/BCN7

A13T3

A15M7

BA0M2

BA1N8

BA2M3

CKJ7

CKK7

CKEK9

CSL2

ODTK1

RASJ3

CASK3

WEL3

RESETT2

DQSLF3

DQSLG3

DQSUC7

DQSUB7

DMLE7

DMUD3

DQL0E3

DQL1F7

DQL2F2

DQL3F8

DQL4H3

DQL5H8

DQL6G2

DQL7H7

DQU0D7

DQU1C3

DQU2C8

DQU3C2

DQU4A7

DQU5A2

DQU6B8

DQU7A3

VREFCAM8

VREFDQH1

ZQL8

VDD_1B2

VDD_2D9

VDD_3G7

VDD_4K2

VDD_5K8

VDD_6N1

VDD_7N9

VDD_8R1

VDD_9R9

VDDQ_1A1

VDDQ_2A8

VDDQ_3C1

VDDQ_4C9

VDDQ_5D2

VDDQ_6E9

VDDQ_7F1

VDDQ_8H2

VDDQ_9H9

NC_1J1

NC_2J9

NC_3L1

NC_4L9

NC_6T7

VSS_1A9

VSS_2B3

VSS_3E1

VSS_4G8

VSS_5J2

VSS_6J8

VSS_7M1

VSS_8M9

VSS_9P1

VSS_10P9

VSS_11T1

VSS_12T9

VSSQ_1B1

VSSQ_2B9

VSSQ_3D1

VSSQ_4D8

VSSQ_5E2

VSSQ_6E8

VSSQ_7F9

VSSQ_8G1

VSSQ_9G9


DDR_HYNIX

A0N3

A1P7

A2P3

A3N2

A4P8

A5P2

A6R8

A7R2

A8T8

A9R3

A10/APL7

A11R7

A12/BCN7

A13T3

A15M7

BA0M2

BA1N8

BA2M3

CKJ7

CKK7

CKEK9

CSL2

ODTK1

RASJ3

CASK3

WEL3

RESETT2

DQSLF3

DQSLG3

DQSUC7

DQSUB7

DMLE7

DMUD3

DQL0E3

DQL1F7

DQL2F2

DQL3F8

DQL4H3

DQL5H8

DQL6G2

DQL7H7

DQU0D7

DQU1C3

DQU2C8

DQU3C2

DQU4A7

DQU5A2

DQU6B8

DQU7A3

VREFCAM8

VREFDQH1

ZQL8

VDD_1B2

VDD_2D9

VDD_3G7

VDD_4K2

VDD_5K8

VDD_6N1

VDD_7N9

VDD_8R1

VDD_9R9

VDDQ_1A1

VDDQ_2A8

VDDQ_3C1

VDDQ_4C9

VDDQ_5D2

VDDQ_6E9

VDDQ_7F1

VDDQ_8H2

VDDQ_9H9

NC_1J1

NC_2J9

NC_3L1

NC_4L9

NC_6T7

VSS_1A9

VSS_2B3

VSS_3E1

VSS_4G8

VSS_5J2

VSS_6J8

VSS_7M1

VSS_8M9

VSS_9P1

VSS_10P9

VSS_11T1

VSS_12T9

VSSQ_1B1

VSSQ_2B9

VSSQ_3D1

VSSQ_4D8

VSSQ_5E2

VSSQ_6E8

VSSQ_7F9

VSSQ_8G1

VSSQ_9G9

NT5CB128M16BP-DIIC701-*1

DDR_NANYA

A0N3

A1P7

A2P3

A3N2

A4P8

A5P2

A6R8

A7R2

A8T8

A9R3

A10/APL7

A11R7

A12N7

NC_6T3

NC_5M7

BA0M2

BA1N8

BA2M3

CKJ7

CKK7

CKEK9

CSL2

ODTK1

RASJ3

CASK3

WEL3

RESETT2

DQSLF3

DQSLG3

DQSUC7

DQSUB7

DMLE7

DMUD3

DQL0E3

DQL1F7

DQL2F2

DQL3F8

DQL4H3

DQL5H8

DQL6G2

DQL7H7

DQU0D7

DQU1C3

DQU2C8

DQU3C2

DQU4A7

DQU5A2

DQU6B8

DQU7A3

VREFCAM8

VREFDQH1

ZQL8

VDD_1B2

VDD_2D9

VDD_3G7

VDD_4K2

VDD_5K8

VDD_6N1

VDD_7N9

VDD_8R1

VDD_9R9

VDDQ_1A1

VDDQ_2A8

VDDQ_3C1

VDDQ_4C9

VDDQ_5D2

VDDQ_6E9

VDDQ_7F1

VDDQ_8H2

VDDQ_9H9

NC_1J1

NC_2J9

NC_3L1

NC_4L9

NC_7T7

VSS_1A9

VSS_2B3

VSS_3E1

VSS_4G8

VSS_5J2

VSS_6J8

VSS_7M1

VSS_8M9

VSS_9P1

VSS_10P9

VSS_11T1

VSS_12T9

VSSQ_1B1

VSSQ_2B9

VSSQ_3D1

VSSQ_4D8

VSSQ_5E2

VSSQ_6E8

VSSQ_7F9

VSSQ_8G1

VSSQ_9G9


DDR_NANYA

A0N3

A1P7

A2P3

A3N2

A4P8

A5P2

A6R8

A7R2

A8T8

A9R3

A10/APL7

A11R7

A12N7

NC_6T3

NC_5M7

BA0M2

BA1N8

BA2M3

CKJ7

CKK7

CKEK9

CSL2

ODTK1

RASJ3

CASK3

WEL3

RESETT2

DQSLF3

DQSLG3

DQSUC7

DQSUB7

DMLE7

DMUD3

DQL0E3

DQL1F7

DQL2F2

DQL3F8

DQL4H3

DQL5H8

DQL6G2

DQL7H7

DQU0D7

DQU1C3

DQU2C8

DQU3C2

DQU4A7

DQU5A2

DQU6B8

DQU7A3

VREFCAM8

VREFDQH1

ZQL8

VDD_1B2

VDD_2D9

VDD_3G7

VDD_4K2

VDD_5K8

VDD_6N1

VDD_7N9

VDD_8R1

VDD_9R9

VDDQ_1A1

VDDQ_2A8

VDDQ_3C1

VDDQ_4C9

VDDQ_5D2

VDDQ_6E9

VDDQ_7F1

VDDQ_8H2

VDDQ_9H9

NC_1J1

NC_2J9

NC_3L1

NC_4L9

NC_7T7

VSS_1A9

VSS_2B3

VSS_3E1

VSS_4G8

VSS_5J2

VSS_6J8

VSS_7M1

VSS_8M9

VSS_9P1

VSS_10P9

VSS_11T1

VSS_12T9

VSSQ_1B1

VSSQ_2B9

VSSQ_3D1

VSSQ_4D8

VSSQ_5E2

VSSQ_6E8

VSSQ_7F9

VSSQ_8G1

VSSQ_9G9


DDR_NANYA

A0N3

A1P7

A2P3

A3N2

A4P8

A5P2

A6R8

A7R2

A8T8

A9R3

A10/APL7

A11R7

A12N7

NC_6T3

NC_5M7

BA0M2

BA1N8

BA2M3

CKJ7

CKK7

CKEK9

CSL2

ODTK1

RASJ3

CASK3

WEL3

RESETT2

DQSLF3

DQSLG3

DQSUC7

DQSUB7

DMLE7

DMUD3

DQL0E3

DQL1F7

DQL2F2

DQL3F8

DQL4H3

DQL5H8

DQL6G2

DQL7H7

DQU0D7

DQU1C3

DQU2C8

DQU3C2

DQU4A7

DQU5A2

DQU6B8

DQU7A3

VREFCAM8

VREFDQH1

ZQL8

VDD_1B2

VDD_2D9

VDD_3G7

VDD_4K2

VDD_5K8

VDD_6N1

VDD_7N9

VDD_8R1

VDD_9R9

VDDQ_1A1

VDDQ_2A8

VDDQ_3C1

VDDQ_4C9

VDDQ_5D2

VDDQ_6E9

VDDQ_7F1

VDDQ_8H2

VDDQ_9H9

NC_1J1

NC_2J9

NC_3L1

NC_4L9

NC_7T7

VSS_1A9

VSS_2B3

VSS_3E1

VSS_4G8

VSS_5J2

VSS_6J8

VSS_7M1

VSS_8M9

VSS_9P1

VSS_10P9

VSS_11T1

VSS_12T9

VSSQ_1B1

VSSQ_2B9

VSSQ_3D1

VSSQ_4D8

VSSQ_5E2

VSSQ_6E8

VSSQ_7F9

VSSQ_8G1

VSSQ_9G9


DDR_NANYA

A0N3

A1P7

A2P3

A3N2

A4P8

A5P2

A6R8

A7R2

A8T8

A9R3

A10/APL7

A11R7

A12N7

NC_6T3

NC_5M7

BA0M2

BA1N8

BA2M3

CKJ7

CKK7

CKEK9

CSL2

ODTK1

RASJ3

CASK3

WEL3

RESETT2

DQSLF3

DQSLG3

DQSUC7

DQSUB7

DMLE7

DMUD3

DQL0E3

DQL1F7

DQL2F2

DQL3F8

DQL4H3

DQL5H8

DQL6G2

DQL7H7

DQU0D7

DQU1C3

DQU2C8

DQU3C2

DQU4A7

DQU5A2

DQU6B8

DQU7A3

VREFCAM8

VREFDQH1

ZQL8

VDD_1B2

VDD_2D9

VDD_3G7

VDD_4K2

VDD_5K8

VDD_6N1

VDD_7N9

VDD_8R1

VDD_9R9

VDDQ_1A1

VDDQ_2A8

VDDQ_3C1

VDDQ_4C9

VDDQ_5D2

VDDQ_6E9

VDDQ_7F1

VDDQ_8H2

VDDQ_9H9

NC_1J1

NC_2J9

NC_3L1

NC_4L9

NC_7T7

VSS_1A9

VSS_2B3

VSS_3E1

VSS_4G8

VSS_5J2

VSS_6J8

VSS_7M1

VSS_8M9

VSS_9P1

VSS_10P9

VSS_11T1

VSS_12T9

VSSQ_1B1

VSSQ_2B9

VSSQ_3D1

VSSQ_4D8

VSSQ_5E2

VSSQ_6E8

VSSQ_7F9

VSSQ_8G1

VSSQ_9G9

C7160.1uF

C7140.1uF

C7150.1uF

C7130.1uF

C7110.1uF

C7120.1uF

C7100.1uF

C7090.1uF

C7360.1uF

C7350.1uF

C7340.1uF

C7330.1uF

C7370.1uF

C7390.1uF

C7400.1uF

C7380.1uF

C7420.1uF

C7440.1uF

C7430.1uF

C7410.1uF

C7490.1uF

C7470.1uF

C7480.1uF

C7460.1uF

IC105LGE2112

DDRV_44AC1

DDRV_45AC2

DDRV_1A3

DDRV_2A4

DDRV_5B4

DDRV_8C4

DDRV_10D4

DDRV_4B3

DDRV_7C3

DDRV_46AC3

DDRV_47AC4

MEMTPG10

MEMTNG9

RVREF_BG13

RVREF_AG21

ARCKEF10

ARCLK1D9

ARCLK1C9

ARCLK0A20

ARCLK0A21

ARODTE18

ARRASF17

ARCASE17

ARCSE16

ARWED14

ARRESETB14

ARBA0A13

ARBA1G11

ARBA2D16

ARCSXF18

ARA14C15

ARA13A15

ARA12F13

ARA11C14

ARA10F11

ARA9E15

ARA8D13

ARA7B15

ARA6E14

ARA5F16

ARA4E13

ARA3B13

ARA2A14

ARA1F14

ARA0F15

ARDQM0C19

ARDQS0C21

ARDQS0B21

ARDQ0C23

ARDQ1B17

ARDQ2D23

ARDQ3C17

ARDQ4D24

ARDQ5C16

ARDQ6C24

ARDQ7D15

ARDQM1D21

ARDQS1B20

ARDQS1C20

ARDQ8A17

ARDQ9A23

ARDQ10D17

ARDQ11B23

ARDQ12D20

ARDQ13D22

ARDQ14D19

ARDQ15C22

ARDQM2A7

ARDQS2B9

ARDQS2A9

ARDQ16C12

ARDQ17D6

ARDQ18B12

ARDQ19C5

ARDQ20C13

ARDQ21A5

ARDQ22A12

ARDQ23B5

ARDQM3E10

ARDQS3C8

ARDQS3D8

ARDQ24C6

ARDQ25D10

ARDQ26D7

ARDQ27C11

ARDQ28C7

ARDQ29C10

ARDQ30B7

ARDQ31B10

AVDD33_MEMPLLN14

AVSS33_MEMPLLN15

DVSS_50R1

DVSS_48P21

IC105LGE2112

RVREF_CP13

RVREF_DV7

BRCLK0F4

BRCLK0F3

BRCLK1V4

BRCLK1V3

BRCKEP6

BRODTH6

BRRASH4

BRCASH5

BRCSK3

BRBA0N1

BRBA1P5

BRBA2K4

BRWEL4

BRA14L5

BRA13M4

BRA12N5

BRA11M5

BRA10P4

BRA9M3

BRA8L6

BRA7L3

BRA6N4

BRA5K5

BRA4N6

BRA3N2

BRA2M1

BRA1N3

BRA0K6

BRCSXG5

DDRV_11D5

DDRV_13E5

DDRV_38T5

DDRV_42V5

DDRV_40U5

DDRV_14E6

DDRV_18F6

DDRV_23G6

DDRV_41U6

DDRV_39T6

DDRV_48AC5

DDRV_19F7

DDRV_24G7

DDRV_49AC6

DDRV_36N7

DDRV_37P7

DDRV_43V6

DDRV_35J10

DDRV_32H10

DDRV_33H13

DDRV_15E20

DDRV_20F20

DDRV_27G20

DDRV_25G15

DDRV_26G18

DDRV_12D25

DDRV_9C25

DDRV_6B25

DDRV_3A25

DDRV_30H7

DDRV_31H8

DDRV_34J8

BRDQM0G2

BRDQS0E4

BRDQS0E3

BRDQ0A1

BRDQ1J1

BRDQ2B2

BRDQ3J2

BRDQ4C2

BRDQ5K1

BRDQ6A2

BRDQ7K2

BRDQM1D1

BRDQS1F1

BRDQS1F2

BRDQ8J3

BRDQ9B1

BRDQ10H3

BRDQ11D3

BRDQ12G3

BRDQ13C1

BRDQ14G4

BRDQ15D2

BRDQM2Y1

BRDQS2V2

BRDQS2V1

BRDQ16T4

BRDQ17AB4

BRDQ18P2

BRDQ19AB3

BRDQ20P3

BRDQ21AB1

BRDQ22P1

BRDQ23AB2

BRDQM3U1

BRDQS3W3

BRDQS3W4

BRDQ24AA3

BRDQ25U4

BRDQ26AA4

BRDQ27T3

BRDQ28Y3

BRDQ29U3

BRDQ30Y2

BRDQ31U2

BRRESETM2

DDRV_16E23

DDRV_22F24

DDRV_29G24

DDRV_21F23

DDRV_28G23

DDRV_17E24

DVSS_15E12

DVSS_23F12

DVSS_1A18

DVSS_3B18

DVSS_5C18

DVSS_9D18

DVSS_16E19

DVSS_24F19

DVSS_31G19

DVSS_32G22

DVSS_19E25

DVSS_2A26

DVSS_4B26

DVSS_6C26

DVSS_10D26

K4B2G1646C-HCK0IC701-*2

DDR_SS

A0N3

A1P7

A2P3

A3N2

A4P8

A5P2

A6R8

A7R2

A8T8

A9R3

A10/APL7

A11R7

A12/BCN7

A13T3

NC_5M7

BA0M2

BA1N8

BA2M3

CKJ7

CKK7

CKEK9

CSL2

ODTK1

RASJ3

CASK3

WEL3

RESETT2

DQSLF3

DQSLG3

DQSUC7

DQSUB7

DMLE7

DMUD3

DQL0E3

DQL1F7

DQL2F2

DQL3F8

DQL4H3

DQL5H8

DQL6G2

DQL7H7

DQU0D7

DQU1C3

DQU2C8

DQU3C2

DQU4A7

DQU5A2

DQU6B8

DQU7A3

VREFCAM8

VREFDQH1

ZQL8

VDD_1B2

VDD_2D9

VDD_3G7

VDD_4K2

VDD_5K8

VDD_6N1

VDD_7N9

VDD_8R1

VDD_9R9

VDDQ_1A1

VDDQ_2A8

VDDQ_3C1

VDDQ_4C9

VDDQ_5D2

VDDQ_6E9

VDDQ_7F1

VDDQ_8H2

VDDQ_9H9

NC_1J1

NC_2J9

NC_3L1

NC_4L9

NC_6T7

VSS_1A9

VSS_2B3

VSS_3E1

VSS_4G8

VSS_5J2

VSS_6J8

VSS_7M1

VSS_8M9

VSS_9P1

VSS_10P9

VSS_11T1

VSS_12T9

VSSQ_1B1

VSSQ_2B9

VSSQ_3D1

VSSQ_4D8

VSSQ_5E2

VSSQ_6E8

VSSQ_7F9

VSSQ_8G1

VSSQ_9G9

K4B2G1646C-HCK0IC703-*2

DDR_SS

A0N3

A1P7

A2P3

A3N2

A4P8

A5P2

A6R8

A7R2

A8T8

A9R3

A10/APL7

A11R7

A12/BCN7

A13T3

NC_5M7

BA0M2

BA1N8

BA2M3

CKJ7

CKK7

CKEK9

CSL2

ODTK1

RASJ3

CASK3

WEL3

RESETT2

DQSLF3

DQSLG3

DQSUC7

DQSUB7

DMLE7

DMUD3

DQL0E3

DQL1F7

DQL2F2

DQL3F8

DQL4H3

DQL5H8

DQL6G2

DQL7H7

DQU0D7

DQU1C3

DQU2C8

DQU3C2

DQU4A7

DQU5A2

DQU6B8

DQU7A3

VREFCAM8

VREFDQH1

ZQL8

VDD_1B2

VDD_2D9

VDD_3G7

VDD_4K2

VDD_5K8

VDD_6N1

VDD_7N9

VDD_8R1

VDD_9R9

VDDQ_1A1

VDDQ_2A8

VDDQ_3C1

VDDQ_4C9

VDDQ_5D2

VDDQ_6E9

VDDQ_7F1

VDDQ_8H2

VDDQ_9H9

NC_1J1

NC_2J9

NC_3L1

NC_4L9

NC_6T7

VSS_1A9

VSS_2B3

VSS_3E1

VSS_4G8

VSS_5J2

VSS_6J8

VSS_7M1

VSS_8M9

VSS_9P1

VSS_10P9

VSS_11T1

VSS_12T9

VSSQ_1B1

VSSQ_2B9

VSSQ_3D1

VSSQ_4D8

VSSQ_5E2

VSSQ_6E8

VSSQ_7F9

VSSQ_8G1

VSSQ_9G9

K4B2G1646C-HCK0IC704-*2

DDR_SS

A0N3

A1P7

A2P3

A3N2

A4P8

A5P2

A6R8

A7R2

A8T8

A9R3

A10/APL7

A11R7

A12/BCN7

A13T3

NC_5M7

BA0M2

BA1N8

BA2M3

CKJ7

CKK7

CKEK9

CSL2

ODTK1

RASJ3

CASK3

WEL3

RESETT2

DQSLF3

DQSLG3

DQSUC7

DQSUB7

DMLE7

DMUD3

DQL0E3

DQL1F7

DQL2F2

DQL3F8

DQL4H3

DQL5H8

DQL6G2

DQL7H7

DQU0D7

DQU1C3

DQU2C8

DQU3C2

DQU4A7

DQU5A2

DQU6B8

DQU7A3

VREFCAM8

VREFDQH1

ZQL8

VDD_1B2

VDD_2D9

VDD_3G7

VDD_4K2

VDD_5K8

VDD_6N1

VDD_7N9

VDD_8R1

VDD_9R9

VDDQ_1A1

VDDQ_2A8

VDDQ_3C1

VDDQ_4C9

VDDQ_5D2

VDDQ_6E9

VDDQ_7F1

VDDQ_8H2

VDDQ_9H9

NC_1J1

NC_2J9

NC_3L1

NC_4L9

NC_6T7

VSS_1A9

VSS_2B3

VSS_3E1

VSS_4G8

VSS_5J2

VSS_6J8

VSS_7M1

VSS_8M9

VSS_9P1

VSS_10P9

VSS_11T1

VSS_12T9

VSSQ_1B1

VSSQ_2B9

VSSQ_3D1

VSSQ_4D8

VSSQ_5E2

VSSQ_6E8

VSSQ_7F9

VSSQ_8G1

VSSQ_9G9

K4B2G1646C-HCK0IC702-*2

DDR_SS

A0N3

A1P7

A2P3

A3N2

A4P8

A5P2

A6R8

A7R2

A8T8

A9R3

A10/APL7

A11R7

A12/BCN7

A13T3

NC_5M7

BA0M2

BA1N8

BA2M3

CKJ7

CKK7

CKEK9

CSL2

ODTK1

RASJ3

CASK3

WEL3

RESETT2

DQSLF3

DQSLG3

DQSUC7

DQSUB7

DMLE7

DMUD3

DQL0E3

DQL1F7

DQL2F2

DQL3F8

DQL4H3

DQL5H8

DQL6G2

DQL7H7

DQU0D7

DQU1C3

DQU2C8

DQU3C2

DQU4A7

DQU5A2

DQU6B8

DQU7A3

VREFCAM8

VREFDQH1

ZQL8

VDD_1B2

VDD_2D9

VDD_3G7

VDD_4K2

VDD_5K8

VDD_6N1

VDD_7N9

VDD_8R1

VDD_9R9

VDDQ_1A1

VDDQ_2A8

VDDQ_3C1

VDDQ_4C9

VDDQ_5D2

VDDQ_6E9

VDDQ_7F1

VDDQ_8H2

VDDQ_9H9

NC_1J1

NC_2J9

NC_3L1

NC_4L9

NC_6T7

VSS_1A9

VSS_2B3

VSS_3E1

VSS_4G8

VSS_5J2

VSS_6J8

VSS_7M1

VSS_8M9

VSS_9P1

VSS_10P9

VSS_11T1

VSS_12T9

VSSQ_1B1

VSSQ_2B9

VSSQ_3D1

VSSQ_4D8

VSSQ_5E2

VSSQ_6E8

VSSQ_7F9

VSSQ_8G1

VSSQ_9G9

DDR ONE SIDE 12

2011.12.09




MT5369_TS_IN[5] CI_TS_DATA[5]

MT5369_TS_IN[3]

CI_TS_DATA[6]

CI_TS_DATA[1]MT5369_TS_IN[2]

CI_TS_DATA[2]

CI_TS_DATA[3]

MT5369_TS_IN[0]

MT5369_TS_IN[4]

MT5369_TS_IN[1]CI_TS_DATA[0]

CI_TS_DATA[7]MT5369_TS_IN[7]

MT5369_TS_IN[6]

CI_TS_DATA[4]

CI_MDI[1]

CI_MDI[0]MT5369_TS_OUT[0]

MT5369_TS_OUT[1]

MT5369_TS_OUT[2]

MT5369_TS_OUT[3] CI_MDI[3]

CI_MDI[2]

MT5369_TS_OUT[4]

MT5369_TS_OUT[5]

MT5369_TS_OUT[6]

MT5369_TS_OUT[7] CI_MDI[7]

CI_MDI[6]

CI_MDI[5]

CI_MDI[4]

CI_A_DATA[0]

CI_MDI[6]

CI_MDI[3]

CI_MDI[7]

CI_MDI[5]

CI_MDI[2]

CI_MDI[4]

CI_MDI[1]

CI_MDI[0]

CI_A_DATA[2]

CI_A_DATA[1]

CI_A_DATA[6]

CI_A_DATA[7]

CI_A_DATA[5]

CI_A_DATA[3]

CI_A_DATA[4]

CI_A_DATA[0]

CI_A_DATA[1]

CI_A_DATA[2]

CI_A_DATA[3]

CI_A_DATA[4]

CI_A_DATA[5]

CI_A_DATA[6]

CI_A_DATA[7] CI_DATA[7]

CI_DATA[6]

CI_DATA[5]

CI_DATA[4]

CI_DATA[3]

CI_DATA[2]

CI_DATA[1]

CI_DATA[0]

CI_A_ADDR[0]

CI_A_ADDR[1]

CI_A_ADDR[2]

CI_A_ADDR[3]

CI_A_ADDR[4]

CI_A_ADDR[5]

CI_A_ADDR[6]

CI_A_ADDR[7]

CI_A_ADDR[8]

CI_A_ADDR[9]

CI_A_ADDR[10]

CI_A_ADDR[11]

CI_A_ADDR[12]

CI_A_ADDR[13]

CI_A_ADDR[14] CI_ADDR[14]

CI_ADDR[13]

CI_ADDR[12]

CI_ADDR[11]

CI_ADDR[10]

CI_ADDR[9]

CI_ADDR[8]

CI_ADDR[7]

CI_ADDR[6]

CI_ADDR[5]

CI_ADDR[4]

CI_ADDR[3]

CI_ADDR[2]

CI_ADDR[1]

CI_ADDR[0]

MT5369_TS_OUT[0-7]

MT5369_TS_CLK

R908 47

CI_IN_TS_CLK

C90212pF50VOPT

MT5369_MCLKI

CI_IN_TS_SYNC

CI_TS_CLK

MT5369_MISTRT

R917 47 CI

AR901 47 CI

MT5369_MIVAL_ERR

CI_MDI[0-7]

CI_IN_TS_VAL

CI_TS_SYNC

CI_TS_DATA[0-7]

R916 47 CIMT5369_TS_VAL

R907 47

AR900 47 CI

CI_TS_VAL

R915 47 CI

MT5369_TS_SYNC

MT5369_TS_IN[0-7]

R909 47

C90012pF50VOPT

AR902

47CI

AR90347

CI

CI_A_ADDR[8]

/PCM_IOWR

CI_TS_CLK

R92910KCI

CI_IN_TS_SYNC

CI_A_ADDR[7]

+5V_CI_ON

CI_A_ADDR[2]

CI_A_ADDR[10]

/PCM_OE

R912 22

/CI_CD2

R92310KOPT

CI_TS_DATA[0]

/CI_CD1

PCM_RST

R938 0 OPT

CI_A_ADDR[0]

C90510uF10VCI

R925 0

C9040.1uFCI

R940 22 CI

/CI_CD1

R922 22 CI

PCM_INPACK

/PCM_CE1

R936

10K

CI

CI_A_ADDR[5]

R928 100CI

CI_A_ADDR[14]

CI_TS_DATA[1]

R921 22 CI

R92410KOPT

CI_A_DATA[0-7]

R941 22

C9070.1uF16V

CI

/CI_CD2

CI_MDI[0-7]

CI_VS1

/PCM_IORD

CI_A_ADDR[11]

+5V_CI_ON

+3.3V_NORMAL

R93410KOPT

/PCM_CE1

/PCM_IOWR

CI_IN_TS_VAL

CI_IN_TS_CLK

/PCM_WE

R920 22 OPT

CI_TS_DATA[3]

/PCM_WE

CI_A_ADDR[6]

CI_TS_SYNC

R942 22

CI_TS_DATA[2]

+5V_CI_ON

R91010KCI

CI_TS_DATA[4]

R911 22

R93310KOPT

R927 100

CI

R932 22

OPT

CI_TS_DATA[5]

PCM_RST

CI_TS_VAL

R926 0 OPT

C906 0.1uF

CI

CI_A_ADDR[9]

R939 22CI

CI_A_ADDR[1]

/PCM_CE2

R937 10K

OPT

/PCM_IORD

CI_A_ADDR[4]

CI_A_ADDR[13]

/PCM_OE

/PCM_IRQA

CI_A_ADDR[3]

R91410KCI

/PCM_A_REG

CI_A_ADDR[12]

+3.3V_NORMAL

CI_TS_DATA[7]

R935

10KCI

/PCM_WAIT

R93122

OPT

R90610KOPT

CI_TS_DATA[6]

CI_DATA[0-7]CI_A_DATA[0-7]

CI_A_ADDR[0-14] CI_ADDR[0-14]

/PCM_WAIT

PCM_INPACK

/PCM_IRQA

CI_VS1

/PCM_REG

/PCM_CE2

/PCM_A_REG /PCM_REG

CI_A_VS1 CI_VS1

AR906 0 CI

AR907 0 CI

AR904 0 CI

AR908 0 CI

AR905 0 CI

AR909 0 CI

R91947KCI

R93047KCI

R91847KCI

R91347KCI

JK900

10118309-015LF

CI

G1G2

57TS_OUT_CLK

21 ADDR12

52VPP

16 /IRQA

10 ADDR11

47TS_IN0

41TS_OUT7

5 DAT6

36/CI_DET1

59CI_WAIT

23 ADDR6

45IOWR

54TS_IN5

18 VPP

49TS_IN2

43VS1

13 ADDR13

7 /CARD_EN1

38TS_OUT4

2 DAT3

25 ADDR4

56TS_IN7

20 TS_IN_CLK

51VCC

15 /WR_EN

9 /O_EN

46TS_IN_SYN

40TS_OUT6

4 DAT5

35GND

58CI_RESET

22 ADDR7

53TS_IN4

17 VCC

11 ADDR10

48TS_IN1

42CARD_EN2

12 ADDR8

6 DAT6

37TS_OUT3

1 GND

24 ADDR5

55TS_IN6

19 TS_IN_VAL

50TS_IN3

44IORD

14 ADDR14

8 ADDR10

39TS_OUT5

3 DAT4

26 ADDR360INPACK

27 ADDR261REG

28 ADDR162TS_OUT_VAL

29 ADDR063TS_OUT_SYN

30 DAT064TS_OUT0

31 DAT1

32 DAT2

33 /IO_BIT

34 GND

65TS_OUT1

66TS_OUT2

67/CI_DET2

68GND

69

R90010KOPT

13

2011.11.21MID_MAIN_CI

Close to CI Slot

CI TS INPUT

Close to MT5369

Close to MT5369

Close to CI Slot

Close to CI Slot

CI TS OUTPUT

Close to MT5369

CI DETECT



THERMAL

THERMAL

THERMAL

THERMAL


C24320.01uF

50V

L2407BLM18PG121SN1D

+1.5V_DDR

+5V_NORMAL

C241510uF16V

R2432330K1/16W 5%

Q2406MMBT3904(NXP)

E

B

C

+3.5V_ST

L2412

BLM18PG121SN1D

NON_CN

C24010.1uF50V

L2405BLM18PG121SN1D

C2422

0.01uF50V

C2416100pF50V

C24060.1uF16V

C241810uF10V

R243356K1/16W1%

L2408

BLM18SG121TN1D

+24V

C24171uF10V

R243115K

1/16W 5%

R2425100

Q2407AO3407A

G

DS

C24120.1uF16V

P2401

SMAW200-H24S2

1912V

14 GND

93.5V

4 24V

18 INV ON

13GND

8 GND

324V

1712V

12 3.5V

7GND

2 24V

16 GND/V-sync

113.5V

6 GND

1PWR ON

20 A.DIM

15GND

10 3.5V

5GND

2112V 22 P.DIM1

23GND/P.DIM2 24 Err OUT

25

R2419100

Q2401

MMBT3906(NXP)

1

2

3

L2403CIS21J121

IC2401

NCP803SN293

OPT

1

GND

3VCC 2 RESET

R243510K

+12V

C24401uF25VOPT

C2423

0.1uF

16V

+3.3V_TU_IN

L2401CIS21J121

R2418100

OPT

R2408

10K

R2416100K

OPT

L24093.6uH

NR8040T3R6N

INV_CTL

C2429

0.1uF16V

ERROR_OUT

R2420

0

POWER_16_GND

+3.5V_ST

L24063.6uH

NR8040T3R6N

R242110KOPT

PWM_DIM2

R24244.7KOPT

IC2403TPS54319TRE

1VIN_1

3GND_1

7COMP

9 SS/TR

10 PH_1

11 PH_2

12 PH_3

13

BOOT

14

PWRGD

15

EN

16

VIN_3

5AGND

8RT/CLK

6VSENSE

4GND_2

2VIN_2 17

EP[GND]

R241305%

OPT

+3.3V_NORMAL

+12V

L2402CIS21J121

R2417100K

L/DIM0_VS

C24330.1uF50V

C24190.1uF16V

+3.5V_ST

R2423 0

POWER_16_VSYNC

C243022uF10V

PANEL_CTL

C2420

0.1uF16V

POWER_DET

IC2404TPS54327DDAR

DEV_DCDC_TPS54327

3VREG5

2VFB

4SS

1EN

5GND

6SW

7VBST

8VIN

9

[EP]GND

C24283300pF50V

+12V

+3.5V_ST

C24110.1uF16V

PWM_DIM1

+3.3V_NORMAL

IC2402

NCP803SN293

1

GND

3VCC 2 RESET

C24270.1uF16V

R2439

10K

1%

R24261K

R2434

47K

1%

+24V

P2400FW20020-24S

OPT

19

14

9

4

18

13

8

3

17

12

7

2

16

11

6

1

20

15

10

5

21 22

23 24

C2426100pF50V

PANEL_VCC

+3.5V_STC24430.1uF50V

R243710K

A_DIM

R2422

0

POWER_24_GND

R2415

56K

1%

C24214700pF

50V

R2442

10K

MTK_EPI

R2441

1.8K

MTK_EPI

+12V

R2430

10K

RL_ON

+3.5V_ST

C24130.1uF

50V

R240110K

C240210uF16V

C24413300pF50VOPT

R240310K

R24000OPT

L24042uH

C240010uF16V

POWER_ON/OFF1

R2406

10K

1%

C24030.1uF16VOPT

C2404

0.1uF16V

IC2400AOZ1038PI

3AGND

2VIN

4FB

1PGND

5COMP

6EN

7NC_1

8NC_2

9

[EP]LX

+12V

C241410uF10V

C240910uF10V

C240810uF10V

C240710uF10V

+1.2V_MTK_CORE

L2400BLM18PG121SN1D

C244522pF50V

C24340.1uF50V

+12V

+3.3V_NORMAL

C243110uF16V

R242810K

1%

C24381uF10V

C24370.1uF

C244222uF10V

C24393300pF50V

R2414 10K

C244422uF10V

R2407100K

L24112uH

+3.3V_NORMAL

R242733K1%

L2410BLM18PG121SN1D

IC2405TPS54425PWPR

3VREG5

2VFB

4SS

1VO

6PG

5GND

7EN

8PGND1

9PGND2

10SW1

11SW2

12VBST

13VIN1

14VIN2

15

[EP]PGND

C24360.1uF16V

POWER_ON/OFF2_1POWER_ON/OFF1

POWER_ON/OFF2_2

POWER_ON/OFF2_3

POWER_ON/OFF2_4

POWER_ON/OFF2_1

POWER_ON/OFF2_3

POWER_ON/OFF2_2

R24023.3K

C24054700pF

50V

R2404

5.6K

1%

C240010.1uF16V

R24102.7K1%

R24111.5K1%OPT

R24091.2K1%

C244610uF10V

C244710uF10V

C242410uF10V

C242510uF10V

C24354.7uF

50V

C244810uF10V

R2451

2K

1/8W

PANEL_DISCHARGE_REG

R2452

2K

1/8W

PANEL_DISCHARGE_REG

R24128.2K5%OPT

R2442-*1

33K

MTK_NON_EPI

R2441-*1

5.6K

MTK_NON_EPI

+3.3V_NORMAL

L2413

BLM18PG121SN1DCN

C24100.1uF50VOPT

R2405

22POWER_24_ERROR_OUT

24

MID_POWER 2011.11.25

Vout=0.827*(1+R1/R2)=1.521V

3AOn-semi

24V-->3.48V

TYP 1450mA

#16/#20/#23LD - GND OR USELE(N.L.D.) - OPENLE(L.D.) - USE

R2

FROM LIPS & POWER B/D

R2

DDR MAIN 1.5V

PANEL_POWER

R1

R1

12V-->3.58V

Power_DET

not to RESET at 8kV ESD

ST_3.5V-->3.5V

$ 0.145

3A

3A

+5V_Normal

Placed on SMD-TOP

*NOTE 17

R1

R2

Vout=0.8*(1+R1/R2)

4A

Vout=(0.763+0.0017*Vout.set)*(1+R1/R2)

+3.3V_NORMAL MAX 3.4 A

R2

R1




EEPROM_SCL

+3.5V_ST

GND

POWER_ON/OFF2_4

EDID_WP

R3023

4.7MOPT

C30040.1uF16V

R3009

10K

MICOM_JAPAN

MICOM_DEBUG

SW3000JTP-1127WEM

MICOM_RESET_SW

12

4 3R3027

270K

OPT

R3026

10K

PANEL_CTL

SOC_RX

POWER_ON/OFF1

IR

SIDE_HP_MUTE

INV_CTL

MICOM_RESET

POWER_ON/OFF2_3

MODEL1_OPT_1

MODEL1_OPT_3

LED_B/GP4_LED_R

AMP_MUTE

AMP_RESET_N

R3022

10K

R3006

10K

MICOM_LCD/OLED

MICOM_RESET

R3012

10K

MICOM_DIIVA

MODEL1_OPT_1

I2C_SCL3

KEY1

MODEL1_OPT_2

EXT_AMP_MUTE

I2C_SDA3

MODEL1_OPT_0

R3025

22

MICOM_DIIVA

+3.5V_ST

COMMERCIAL_12V_CTL

MODEL1_OPT_4

+3.5V_ST

MODEL1_OPT_0

SOC_RESET

12V_EXT_PWR_DET

R3007

10K

MICOM_TOUCH_KEY

POWER_ON/OFF2_1

R3008

10K

MICOM_TACT_KEY

R3010

10K

MICOM_NON_JAPAN

KEY2

SCART_MUTE

R3014

1K

MODEL1_OPT_4

+3.5V_ST

RL_ON

POWER_ON/OFF2_2

R3005

10K

MICOM_PDP

X3000

32.768KHz

R3024

22

MODEL1_OPT_3

EEPROM_SDA

MODEL1_OPT_2HDMI_CEC

R3011

10K

MICOM_DEBUG

POWER_ON/OFF2_3

EXT_AMP_RESET

MICOM_DEBUG

C30000.1uF

SOC_TX

R3013

10K

MICOM_NON_DIIVA

POWER_DET

POWER_ON/OFF2_4

+3.5V_ST

HDMI_CEC

D3000

BAT54_SUZHO

R3029

120K

CEC_REMOTE

R302827K

+3.5V_ST

RUE003N02Q3001

HDMI_CEC_FET_ROHM

SD

G

EXT_AMP_RESET

SCART_MUTE

EXT_AMP_MUTE

12V_EXT_PWR_DET

COMMERCIAL_12V_CTL

R3030

10K

MICOM_GP4_10PIN

R3031

10K

MICOM_GP3_12/15PIN

+3.3V_NORMAL

R3034

4.7KOPT

+3.3V_NORMAL

+3.3V_NORMAL

+3.3V_NORMAL

R3035

4.7KOPT

+3.3V_NORMAL

Q3000MMBT3904(NXP)EDID_WP

E

B

C

P300012507WS-12L

MICOM_DEBUG

1

2

3

4

5

6

7

8

9

10

11

12

13

R3036

10K

OPT

R3037

10K

OPT

R3032

10K

AMP_RESET_BY_MICOM

R3033

10K

IC3000

R5F100GEAFB

MICOM

1P60/SCLA0

2P61/SDAA0

3P62

4P63

5P31/TI03/TO03/INTP4

6P75/KR5/INTP9/SCK01/SCL01

7P74/KR4/INTP8/SI01/SDA01

8P73/KR3/SO01

9P72/KR2/SO21

10P71/KR1/SI21/SDA21

11P70/KR0/SCK21/SCL21

12P30/INTP3/RTC1HZ/SCK11/SCL11

13

P50/INTP1/SI11/SDA11

14

P51/INTP2/SO11

15

P17/TI02/TO02

16

P16/TI01/TO01/INTP5

17

P15/PCLBUZ1/SCK20/SCL20

18

P14/RXD2/SI20/SDA20

19

P13/TXD2/SO20

20

P12/SO00/TXD0/TOOLTXD

21

P11/SI00/RXD0/TOOLRXD/SDA00

22

P10/SCK00/SCL00

23

P146

24

P147/ANI18

25 P27/ANI726 P26/ANI627 P25/ANI528 P24/ANI429 P23/ANI330 P22/ANI231 P21/ANI1/AVREFM32 P20/ANI0/AVREFP33 P13034 P01/TO00/RXD135 P00/TI00/TXD136 P140/PCLBUZ0/INTP6

37

P120/ANI19

38

P41/TI07/TO07

39

P40/TOOL0

40

RESET

41

P124/XT2/EXCLKS

42

P123/XT1

43

P137/INTP0

44

P122/X2/EXCLK

45

P121/X1

46

REGC

47

VSS

48

VDD

C3002

8pF

C3003

8pF R3000

10K

R3001

22

MICOM_DIIVA

POD_WAKEUP_N

FLG_POD_DR

/RST_DIIVA

FLG_POD_DR

/RST_DIIVA

POD_WAKEUP_N

R3002

22

MICOM_DIIVA

R3003 22

AMP_RESET_BY_MICOM

MODEL1_OPT_6

MODEL1_OPT_5

MODEL1_OPT_6

MODEL1_OPT_5

R3020

10K

MICOM_MHL

R3021

10K

MICOM_NON_MHL

R3016

10K

MICOM_GED

R3017

10K

MICOM_NON_GED

C3001

0.47uF

LOGO_LIGHT

LOGO_LIGHT

SI1012CR-T1-GE3Q3001-*1

HDMI_CEC_FET_VISHAYSD

G

R30183.3K

R30193.3K

R3005-*1

56K

MICOM_OLED_MAIN

R3005-*2

22K

MICOM_OLED_FRC

MICOM 30

For Debug

PDP

DIVA

Renesas MICOM

NON DIVA

/ OLED

MICOM MODEL OPTION

MODEL_OPT_3 LCD

For CEC

IR Wafer

10PinMODEL_OPT_4

12/15Pin

IR Wafer

10

MODEL_OPT_0

MODEL_OPT_1

MODEL_OPT_2

JAPANNON JAPAN

TOUCH_KEYTACT_KEY

GP4 High/MID Power SEQUENCE

POWER_ON/OFF!

POWER_ON/OFF2_1

POWER_ON/OFF2_2

POWER_ON/OFF2_3

POWER_ON/OFF2_4

SOC_RESET

For Japan:LNB_INIT

HDMI_WAUP:HDMI_INIT

2011.12.12

for DiiVA

For China

(GP3_Soft touch)

NON_MHL MHLMODEL_OPT_5

NON_GED GEDMODEL_OPT_6

For JAPAN

GP4_HIGH

(GP4_TOOL)For Sample Set

MICOM MODEL OPTION

Eye Sensor Option

MODEL_OPT_2

10

MC8101_ABOVN/A

MODEL_OPT_4

0

1 CM3231_CAPELLA CM3231_CAPELLA

(TACT_KEY)

(GP3 Soft touch) (GP4 Soft touch)

Don’t remove R3014,not making float P40




D1-_HDMI1_SOC

D0+_HDMI1_SOC

R3303 100

R331922

HDMI_EXT_EDID

DDC_SDA_2_JACK

R3314 100

5V_HDMI_3_JACK

R33051K

R332547K

CEC_REMOTE

D1-_HDMI2_JACK

5V_HDMI_2_JACK

R332447K

R332022

HDMI_EXT_EDID

R33161K

R33171K

HDMI_HPD_4_JACK

C33030.1uF16V

JK3300

RSD-105156-100

EAG62611201

14

NC

13

CE_REMOTE

5D1_GND

20

BODY_SHIELD

12

CK-

11

CK_GND

2D2_GND

19

HP_DET

18

5V

10CK+

4D1+

1D2+

17

GND

9D0-

8D0_GND

3D2-

16

DDC_DATA

7D0+

6D1-

15

DDC_CLK

D2+_HDMI2_JACK

+5V_NORMAL

CK-_HDMI2_JACK

D2+_HDMI4_JACK

R332647K

R3313100K

C33010.1uF16V

R333947K

D0-_HDMI4_JACK

R333747K

DDC_SCL_2_JACK

D2-_HDMI4_JACK

R3307100K

5V_HDMI_2_JACK

HDMI_ARC

HDMI_HPD_2_JACK

5V_HDMI_4_JACK

R33111K

+5V_NORMAL

C33020.1uF16V

R333847K

DDC_SCL_4_JACK

5V_HDMI_4_JACK

DDC_SDA_1_SOCDDC_SDA_2_JACK

D0+_HDMI4_JACK

CK+_HDMI2_JACK

R33184.7K

R3308 100

D1+_HDMI2_JACK

R3301100K

R3309 100

D2+_HDMI1_SOC

CK-_HDMI1_SOC

CEC_REMOTE

C33000.1uF16V

R334047K

JK3301

RSD-105156-100

EAG62611201

14

ARC

13

CE_REMOTE

5D1_GND

20

BODY_SHIELD

GND

12

CK-

11

CK_GND

2D2_GND

19

HP_DET

18

5V

10CK+

4D1+

1D2+

17

GND

9D0-

8D0_GND

3D2-

16

DDC_DATA

7D0+

6D1-

15

DDC_CLK

D0-_HDMI2_JACK

DDC_SDA_3_JACK

CK-_HDMI4_JACK

D1+_HDMI1_SOC

D0+_HDMI2_JACK

CK+_HDMI4_JACK

DDC_SCL_2_JACK

R33101K

DDC_SCL_4_JACK

DDC_SCL_3_JACK

CK+_HDMI1_SOC

D2-_HDMI2_JACK

HDMI_HPD_1_SOC

R3315 100

5V_HDMI_1_SOC

+5V_NORMAL

DDC_SDA_4_JACK

5V_HDMI_1_SOC

R33041K

DDC_SCL_1_SOC

D1+_HDMI4_JACK

R332347K

DDC_SDA_4_JACK

R3302 100

DDC_SCL_1_SOC

D1-_HDMI4_JACK

R33064.7KHDMI_INTERNAL_EDID

DDC_SDA_1_SOC

+5V_NORMAL

CEC_REMOTE

D0-_HDMI1_SOC

R33124.7K

EDID_WP

JK3302

RSD-105156-100

EAG62611201

14

NC

13

CE_REMOTE

5D1_GND

20

BODY_SHIELD

12

CK-

11

CK_GND

2D2_GND

19

HP_DET

18

5V

10CK+

4D1+

1D2+

17

GND

9D0-

8D0_GND

3D2-

16

DDC_DATA

7D0+

6D1-

15

DDC_CLK

D2-_HDMI1_SOC

Q3300MMBT3904(NXP)

E

B

C

Q3301MMBT3904(NXP)

E

B

C

Q3302MMBT3904(NXP)

E

B

C

IC3300

M24C02-RMN6T

HDMI_EXT_EDID

3E2

2E1

4VSS

1E0

5SDA

6SCL

7WC

8VCC

5V_HDMI_3_JACK

D0-_HDMI3_JACK

Q3303MMBT3904(NXP)

E

B

C

CK+_HDMI3_JACK

CEC_REMOTE

HDMI_HPD_3_JACK

D2-_HDMI3_JACK

R3329 100

DDC_SDA_3_JACK

D1+_HDMI3_JACK

R3327100K

R33364.7K

D1-_HDMI3_JACK

R3328 100

D2+_HDMI3_JACK

DDC_SCL_3_JACK

D0+_HDMI3_JACK

CK-_HDMI3_JACK

JK3303

RSD-105156-100

EAG62611201

14

NC

13

CE_REMOTE

5D1_GND

20

BODY_SHIELD

12

CK-

11

CK_GND

2D2_GND

19

HP_DET

18

5V

10CK+

4D1+

1D2+

17

GND

9D0-

8D0_GND

3D2-

16

DDC_DATA

7D0+

6D1-

15

DDC_CLK

R33311K

R33301K

R33214.7KHDMI_EXT_EDID

D3300MMBD6100

A2

C

A1

D3302MMBD6100

A2

C

A1

D3303MMBD6100

A2

C

A1

D3301MMBD6100

A2

C

A1

R3300

0

UI : HDMI1UI : HDMI3

UI : HDMI2

33

HDMI 4 2011.10.29

UI : HDMI4



Fiber Optic


JK3601KJA-PH-0-0177

3 DETECT

4 L

5 GND

1 R

+3.3V_NORMAL

R3641

2.7K

D3615

30V

OPT

C363318pF50V

R3644 22

JK36022F11TC1-EM52-4F

CGND

BVCC

AVIN

4

SHIELD

DSUB_B+

R36202.7KOPT

+3.3V_NORMAL

DSUB_G+

RGB_DDC_SCL

DSUB_DET

R364510K

RGB_EDID

DSUB_R+

R3643 22

JK3603

SLIM-15F-D-2

11

22

33

44

55

66

77

88

99

10

10

11

11

12

12

13

13

14

14

15

15

1616

R364610K

C36150.1uF16V

RGB_DDC_SDA

SPDIF_OUT

R361533

C363418pF50V

EDID_WP

PC_R_IN

+5V_NORMAL

DSUB_HSYNC

DSUB_VSYNC

D361630V

OPT

PC_L_IN

R36422.7K

RGB_5VRGB_5V

IC3600M24C02-RMN6T

RGB_EDID

3E2

2E1

4VSS

1E0

5SDA

6SCL

7WC

8VCC

SOC_TX

SOC_RX

D3620MMBD6100

A2

C

A1

R3647100

RGB_DEBUG

D36235.6VOPT

D36115.6V

OPT

D36125.6V

OPT

D360020VOPT

D360120VOPT

D3622

5.5VADUC 5S 02 0R5L

OPT

D3621

5.5VADUC 5S 02 0R5L

OPT

D36135.5V

ADUC 5S 02 0R5L OPT

D3611-*1

5.6VESD_MTK

D3612-*1

5.6VESD_MTK

D3613-*1

5.5V

ADUC 5S 02 0R5L

ESD_MTK

R3602100

RGB_DEBUG

R36000

NON_RGB_DEBUGR3601

0NON_RGB_DEBUG

RGB PC

PC AUDIO

RGB/ PC AUDIO/ SPDIF

SPDIF OUT

36

JACK HIGH / MID 2011.11.21

Closed to JACK




R3700

10KHP_OUT

HP_LOUT

+3.3V_NORMALJK3700

KJA-PH-0-0177

EAG61030001

HP_OUT

3DETECT

4L

5GND

1R

HP_DET

HP_ROUT

VA37005.6VOPT

VA3700-*1

5.6V

ESD_MTK_HP_OUT

VA3700-*2

5.6V

ESD_LG1152_HP_OUT

37

JACK_COMMON 2011.11.21

ESD for LG1152ESD for MTK




AV1_R_IN

C38020.1uF

RS232

C38030.1uF

RS232

COMP1_Pr

+3.5V_ST

AV1_L_IN

+3.3V_NORMAL

AV1_CVBS_DET

IR_OUT

R3814

4.7K

OPT

C38010.1uF

RS232

COMP1_DET

JK3803

SPG09-DB-009

RS232

1

2

3

4

5

6

7

8

9

10

JK3800KJA-PH-1-0177

AV_JACK_BLACK

3 M3_DETECT

4 M4

5 M5_GND

1 M1

6 M6

IC3800

MAX3232CDR

EAN41348201

RS232

3C1-

2V+

4C2+

1C1+

6V-

5C2-

7DOUT2

8RIN2

9ROUT2

10DIN2

11DIN1

12ROUT1

13RIN1

14DOUT1

15GND

16VCC

R3811

4.7K

OPT

COMP1_Pb

C38000.1uF

RS232

JK3801KJA-PH-1-0177

COMP_JACK_BLACK

3 M3_DETECT

4 M4

5 M5_GND

1 M1

6 M6

AV1_CVBS_IN

COMP1_Y

R3821100RS232

+3.3V_NORMAL

R3820100RS232

+3.5V_ST

12V_COMMERCIAL_OUT

12V_COMMERCIAL_OUT

+3.5V_ST

R3834

10K

OPT_RS232

SOC_RX

+3.5V_ST

SOC_TX

P3800

12507WS-04L

UART_4PIN_STRAIGHT

1

2

3

4

5

R381010K

R380610K

D38035.6V

OPT

D38005.6VOPT

D380420VOPT

D380520VOPT

D38015.6V

OPT

D38025.6V

OPT

D3801-*15.6V

ESD_MTK

D3802-*15.6V

ESD_MTK

D3800-*15.6V

ESD_MTK

D3803-*15.6V

ESD_MTK

D3803-*25.6VESD_LG1152

D3801-*25.6V

ESD_LG1152

D3802-*25.6V

ESD_LG1152

D3800-*25.6V

ESD_LG1152

JK3801-*1KJA-PH-1-0177-2

COMP_JACK_GREEN

3 M3_DETECT

4 M4

5 M5_GND

1 M1

6 M6

JK3800-*1KJA-PH-1-0177-1

AV_JACK_YELLOW

3 M3_DETECT

4 M4

5 M5_GND

1 M1

6 M6

P3801

12507WR-04L

UART_4PIN_ANGLE

1

2

3

4

5

RS232C CVBS 1 PHONE JACK

COMPONENT 1 PHONE JACK

38

JACK_COMMON 2011.11.21

12V 1A FOR COMMERCIAL(RS-232C POWER)

FOR COMMERCIAL

ESD For MTK ESD For LG1152




IR

R411810K5%

L4100BLM18PG121SN1D

C41020.1uF

LED_B/GP4_LED_R

+3.5V_ST

+3.5V_ST

R410522

COMMERCIAL_IR

C4107100pF50V

IR_OUT

+3.5V_ST

R411710K5%

C41000.1uF

R410210K

COMMERCIAL_IR

R41080

COMMERCIAL_IR_US

R4113100

KEY1

KEY2

R4123100

EEPROM_SCL

R4124100

R411947K

COMMERCIAL_IR

R411110K

COMMERCIAL_IR_EU

R4114100

+3.5V_ST

+3.5V_ST

C41041000pF50V

+3.5V_ST

+3.5V_ST

EEPROM_SDA

R410447K

COMMERCIAL_IR

R41000

IR_BYPASS

R4125 1.5K

Q4100MMBT3904(NXP)COMMERCIAL_IR E

BC

Q4101MMBT3904(NXP)

COMMERCIAL_IR

E

BC

Q4102MMBT3904(NXP)

COMMERCIAL_IR_EU EB

C

Q4104MMBT3904(NXP)COMMERCIAL_IR

E

BC

R41011K

COMMERCIAL_IR

R41091K

COMMERCIAL_IR_EU

R41153.3K

COMMERCIAL_IR

R41033.3K

COMMERCIAL_IR

R410710K

IR_BYPASS

P4102

12507WR-10L

GP4_IR_10P

1

2

3

4

5

6

7

8

9

10

11

D4106

20VADUC 20S 02 010L

OPT

D4105

20VADUC 20S 02 010L

OPT

D41015.6V

AMOTECH CO., LTD.OPT

D41005.6V

AMOTECH CO., LTD.OPT

D41045.6V

AMOTECH CO., LTD.

OPT

D4106-*1

20VADUC 20S 02 010L

ESD_MTK

10pF

D4105-*1

20VADUC 20S 02 010L

ESD_MTK

10pF

D4100-*1

5.6V

ESD_MTK

ADMC 5M 02 200L

200pF

D4101-*1

5.6V

ESD_MTK

ADMC 5M 02 200L

200pF

D4104-*1

5.6V

ESD_MTKADMC 5M 02 200L

200pF

D4104-*2

5.6V

ESD_LG1152ADMC 5M 02 200L

200pF

D4101-*2

5.6V

ESD_LG1152

ADMC 5M 02 200L

200pF

D4100-*2

5.6V

ESD_LG1152

ADMC 5M 02 200L

200pF

IR & KEY RGB Sensor

COMMERCIAL

Zener Diode is

Soft Touch Micom D/L

close to wafer

41

IR / KEY 2011.11.21

COMMERCIAL




USB DOWN STREAM

USB DOWN STREAM

USB DOWN STREAM

THERMAL

THERMAL

THERMAL


USB_DM1

USB_DP2

USB_DP1

USB_DM2

C4339

10uF

10V

WIFI

USB_DM3

C433322uF10V

WIFI_DP

C43270.1uF16V

+5V_USB

R4339

2K1%

WIFI_DM

R4330

0

USB_DP3

C43344700pF50V

D4304

40V

SMAB34

C4322

10uF

10V

D4303

RCLAMP0502BA

OPT

C43280.01uF50V

C43360.1uF16V

+5V_USB_3

USB_CTL2

C432410uF35V

P4301

12507WR-04L

WIFI

1VDD

2DM

3DP

4GND

5

.

C43200.1uF16V

WIFI

C4321

10uF

10V

WIFI

R4329

330K

OPT

R432810K

JK43033AU04S-305-ZC-(LG)

12

34

5

C4310

10uF

10V

JK43023AU04S-305-ZC-(LG)

12

34

5

C43290.1uF16V

L4302

BLM18PG121SN1D

WIFI120-ohm

C43190.1uF16V

WIFI

C43260.1uF50V

POWER_ON/OFF2_4

D4302

RCLAMP0502BA

OPT

+24V

/USB_OCD2

C433247pF50V

IC4305TPS54331D

3EN

2VIN

4SS/TR

1BOOT

5VSENSE

6COMP

7GND

8PH

JK43003AU04S-305-ZC-(LG)

12

34

5

R432710KOPT

R432310K

USB_CTL1

L43086.8uH

R433620K C4338

1000pF50V

OPT

L4305

BLM18PG121SN1D

D4300

RCLAMP0502BA

OPT

/USB_OCD1

C4323

10uF

10V

+5V_USB_2

+5V_USB_3

+5V_USB_2

C433722uF10V

+5V_USB

+3.3V_NORMAL

/USB_OCD3

C430122uF10V

R4332

10KPOWER_ON/OFF2_4

C43310.1uF16V

+12V

L43073.6uH

C43414.7uF10V

R434210K

5%L4306BLM18PG121SN1D

USB_CTL3

C432510uF16V

C4342100pF50V

USB_DCDC_SN1104041

IC4306-*1BD86180MUV

DEV_USB_DCDC_BD86180

3SS

2COMP

4RT

1EN

6CTL1

5CTL2

7FLG2

8FLG1

9USB_OUT2

10GND_1

11GND_2

12USB_OUT1

13USB_IN_1

14USB_IN_2

15USB_IN_3

16SW_1

17SW_2

18BST

19PGND_1

20PGND_2

21VIN_1

22VIN_2

23GND_3

24VREG

25

[EP]GND

C43404700pF

50V

USB_DCDC_SN1104041C4340-*10.01uF50V

USB_DCDC_BD86180

IC4303TPS2554

3IN_2

2IN_1

4ILIM_SEL

1GND

5EN

6ILIM1

7ILIM0

8OUT_1

9OUT_2

10FAULT

11

[EP]

+3.3V_NORMAL

R4301

10K

R4302

10K

R4303

10K

OPT

R4304

10K

OPT

IC4306USB_DCDC_SN1104041

SN1104041, DC-DC+2CH USB SW

3SS

2COMP

4ROSC

1EN

6EN_SW1

5EN_SW2

7NFAULT2

8NFAULT1

9SW_OUT2

10AGND_1

11AGND_2

12SW_OUT1

13SW_IN_1

14SW_IN_2

15SW_IN_3

16LX_1

17LX_2

18BST

19PGND_1

20PGND_2

21VIN_1

22VIN_2

23AGND_3

24V7V

25

[EP]GND C43000.1uF16V

R4343

820

1%

R4300

27K

1/10W

R4341

27K

1/10W

OPT

R4338

10K

1%

D4300-*2

RCLAMP0502BA

ESD_LG1152

D4304-*1

40V

SX34

D4302-*1

RCLAMP0502BA

ESD_LG1152

D4303-*3

RCLAMP0502BA

ESD_LG1152

43

USB3_HUB_WiFi 2011.10.26

MAX 0.4AFrom SoC

USB3

USB2

USB_WIFI

MAX 2A

Vout=0.8*(1+R1/R2)

MAX 1.5A

R1

DVR Ready

MAX 1.5A

3A

+5V_USB FOR USB1

MAX 1.8A

R2

USB1

For EMI





SC_L_IN

C46024700pF

EU

Q4601MMBT3904(NXP)

EU

E

B

C

C46040.1uF

EU

JK4600

DA1R018H91E

EU

1

AUDIO_R_OUT2

AUDIO_R_IN3

AUDIO_L_OUT4

AUDIO_GND5

B_GND6

AUDIO_L_IN7

B_OUT8

ID9

G_GND10

G_OUT11

R_GND12

R_OUT13

RGB_IO14

SYNC_GND15

SYNC_OUT16

SYNC_IN17

COM_GND18

AV_DET19

SHIELD

SC_G

+12V

R4602390

EU

C46034700pF

EU

R4603390

EU

SC_DET

DTV/MNT_L_OUT

SC_ID

DTV/MNT_V_OUT

R4604180

EU

SC_B

SC_R_IN

+3.3V_NORMAL

R460715K

EU

SC_CVBS_IN

Q4600MMBT3906(NXP)

EUE

B

C

C4600

1000pF50V

EU

R4605470

EU

C4601

1000pF50V

EU

L4600

BLM18PG121SN1D

EU

L4601

BLM18PG121SN1D

EU

R460075

EU

DTV/MNT_R_OUT

SC_FB

SC_R

R460647K

EU

C46060.1uF50V

EU

R460110K

EU

R4608 0

OPT

D46115.6V

OPT

D46075.6VOPT

D46065.6V

OPT

D46055.6VOPT

D4608

5.6VOPT

D46015.6VOPT

D4601-*1

5.6V

ESD_MTK_SCART

200pF

D4605-*2

5.6V

ESD_LG1152_SCART

200pF

D4606-*2

5.6V

ESD_LG1152_SCART

200pF

D4601-*25.6V

ESD_LG1152_SCART

200pF

D4611-*2

5.6V

ESD_LG1152_SCART

200pF

D4600

20V

OPT

D4600-*220V

ESD_LG1152_SCART

10pF

C4605100uF16V

EU

C460747uF25V

EU

D4611-*1

5.6V

ESD_MTK_SCART

200pF

D46095.5VOPT

D46105.5VOPT

D4603

5.5V

OPT

D46025.5V

OPT

D4604

5.5V

OPT

D4609-*15.5V

ESD_MTK_SCART15pF

D4609-*25.5V

ESD_LG1152_SCART15pF

D4610-*1

5.5V

ESD_MTK_SCART

15pF

D4602-*15.5V

ESD_MTK_SCART

15pF

D4603-*15.5V

ESD_MTK_SCART15pF

D4604-*15.5V

ESD_MTK_SCART

15pF

D4600-*120V

ESD_MTK_SCART

10pF

D4605-*1

5.6V

ESD_MTK_SCART

200pF

D4606-*15.6V

ESD_MTK_SCART200pF

46

SCART GENDER 2011.10.26

Full Scart(18 Pin Gender)

Gain=1+Rf/Rg

CLOSE TO JUNCTION

RfRg




M_RFModule_ISP

M_REMOTE_RX

M_REMOTE_TX

+3.3V_NORMAL

L4800

120-ohm

M_REMOTE

M_RFModule_RESET

C4800

0.1uF

P4800

12507WR-08L

M_REMOTE

13.3V

2GND

3RX

4TX

5RESET

6DC

7DD

8GND

9

AR48001001/16W

M_REMOTE3D_SYNC_RF

3D_SYNC_RF

ZigBee_Radio Pulse M_REMOTE OPTION

ALL M_REMOTE OPTION

48

MOTION REMOTE 2011.11.21

Only For PDP




EPHY_RDN

C50020.1uF16V

C50010.01uF50V

EPHY_TDP

EPHY_TDN

C50000.1uF16V

JK5000

XRJH-01A-4-DA7-180-LG(B)

LAN_XML

1P1[CT]

2P2[TD+]

3P3[TD-]

4P4[RD+]

5P5[RD-]

6P6[CT]

7P7

8P8

12

SHIELD

9P9

11P11

10P10[GND]

D1YL_C

D2YL_A

D3GN_C

D4GN_A

C50030.01uF50V

EPHY_RDP

LAN_JACK_POWER

D5000

5.5VOPT

D5002

5.5VOPT

D5003

5.5VOPT

D5001

5.5VOPT

D5001-*2

5.5V

ADUC 5S 02 0R5L

ESD_LG1152

D5003-*2

5.5VADUC 5S 02 0R5L

ESD_LG1152

D5002-*2

5.5VADUC 5S 02 0R5L

ESD_LG1152

D5000-*2

5.5V

ADUC 5S 02 0R5L

ESD_LG1152

D5003-*1

ADUC 5S 02 0R5L

ESD_MTK

D5000-*1

ADUC 5S 02 0R5L

ESD_MTK

D5002-*1

ADUC 5S 02 0R5L

ESD_MTK

D5001-*1

ADUC 5S 02 0R5L

ESD_MTK

JK5000-*1

TLA-6T764

LAN_TDK

1R1

2R2

3R3

4R4

5R5

6R6

7R7

8R8

12

SHIELD

9R9

11R11

10R10[GND]

D1YL_C

D2YL_A

D3GN_C

D4GN_A

Ethernet Block

50

LAN_VERTICAL 2011.12.09




THERMAL


I2C_SDA1

+3.5V_ST

C58180.22uF50V

SPK_R-

R5802

100

+24V_AMP

R581043

C58160.22uF50V

L580410.0uH

C58131uF50V

C58090.1uF50V

+24V_AMP

C58101uF50V

AUD_MASTER_CLK

22 R5808

C58050.1uF16V

L5800CIS21J121

C58170.22uF50VR5813

43

L5801

BLM18PG121SN1D

AUD_SCK

AMP_MUTE

R581143

+3.3V_NORMAL

P5800

WAFER-ANGLE

1

2

3

4

SPK_L-

+3.3V_NORMAL

L580610.0uH

L5802

BLM18PG121SN1D

AUD_LRCK

AMP_RESET_N

C58060.1uF16V

C58042.2uF

10V

R580922I2C_SCL1

C58030.1uF16V

SPK_L-

SPK_R+

SPK_R+

R580722

C5812330pF50V

C58080.1uF16VOPT C5811

330pF50V

SPK_L+

AUD_LRCH

C58070.1uF16V

C58210.22uF50V

L580510.0uH

C58020.1uF50V

C58000.1uF50V

C581510uF35V

C58200.22uF50V

R5801

10K

R5800

10K

SPK_L+

R581243

L580310.0uH

C58190.22uF50V

+24V

C58140.1uF50V

SPK_R-

Q5800MMBT3904(NXP)

E

B

C

C582610uF10V

C582710uF35V

C58280.1uF16V

C58291000pF50VOPT

C58010.1uF16V

IC5800

STA380BW

DEV_STM_AMP

1 VCC_REG2 VSS_REG3 OUT2B4 GND25 VCC26 OUT2A7 OUT1B8 VCC19 GND1

10 OUT1A11 VDD_REG12 GND_REG

13

NC_1

14

NC_2

15

NC_3

16

NC_4

17

NC_5

18

NC_6

19

NC_7

20

NC_8

21

NC_9

22

NC_10

23

NC_11

24

NC_12

25NC_13

26NC_14

27NC_15

28VDDDIG1

29GNDDIG1

30FFX3A

31FFX3B

32EAPD/FFX4A

33TWARNEXT/FFX4B

34VREGFILT

35AGNDPLL

36MCLK

37

BICKI

38

LRCKI

39

SDI

40

RESET

41

PWDN

42

INTLINE

43

SDA

44

SCL

45

SA

46

TESTMODE

47

GNDDIG2

48

VDDDIG2

49

[EP]

C58221000pF50V

C58231000pF50V

C58241000pF50V

C58251000pF50V

GP4_MT5369

58

2011.11.21

AUDIO[ST]

0X38

SPEAKER_L

0x38 when SA=0

SPEAKER_R0x3A when SA=1




SIGN600005

SCART_Rout

SCART_MUTE

SCART_Lout

DTV/MNT_R_OUT

R6012

4.7K

OPT

+12V

C600533pF

EU

R6010

470K

OPT

R6008 33KEU

+3.5V_ST

C6004

0.1uF

50V

EU

R60002.2KEU

L6000

EU

R6002

470K

OPT

Q6000MMBT3904(NXP)

EUE

B

C

R60112.2K

EU

DTV/MNT_R_OUT

C600333pFEU

DTV/MNT_L_OUT

Q6001MMBT3904(NXP)

EUE

B

C

DTV/MNT_L_OUT

R600433KEU

C6002

6800pF

OPT

C6007

6800pF

OPT

C6008

1uF

25V

EUC6000

1uF25VEU

IC6000AZ4580MTR-E1

EU3

IN1+

2IN1-

4VEE

1OUT1

5 IN2+

6 IN2-

7 OUT2

8 VCC

SCART_AMP_R_FB

SCART_AMP_L_FB

R6013510

EU

[SCART AUDIO MUTE]

AUD_OUT >> EU/CHINA_HOTEL_OPT

60

SCART AUDIO AMP 2011.11.21




HP_ROUT_MAIN

R6100

4.7K

HP_LOUT_AMP

R6104

OPT100K

R61054.7K

HP_ROUT_AMP

C61041uF10V

SIDE_HP_MUTE

+3.3V_NORMAL

R61060

OPT

R61024.7KOPT

+3.3V_NORMAL

R61071K

HP_LOUT_MAIN

L6100120-ohmBLM18PG121SN1D

R61034.7K

C610510uF10V

IC6100TPA6132A2

EAN60724701

3INR+

2INL+

4INR-

1INL-

5

OUTR

6

G0

7

G1

8

HPVSS

9CPN

10PGND

11CPP

12HPVDD

13

EN

14

VDD

15

SGND

16

OUTL

C61070.1uF16V

R6101

OPT

Q6100MMBT3904(NXP)

E

B

C

C61001uF10V

C61031uF10V

C61082.2uF10V

C61062.2uF10V

C61092.2uF10V

Close to the IC

From Micom

EARPHONE AMP

2011.09.29HEADPHONE AMP

61




Q6201AO3407A

CI

G

DS

+5V_CI_ON

C62074.7uF10VOPT

R621810K

CI

+5V_NORMAL

C62020.1uF16V

OPT

R62422.2KCI

R622110K

OPT

PCM_5V_CTL

R624810KCI

R62234.7K

CI

R624122K

CI

Q6200MMBT3904(NXP)CI

E

B

C

C62101uF25VOPT

C6210-*11uF25V

CI_MTK

CI POWER ENABLE CONTROL

62

CI SLOT 2011.10.31

Option FOR MTK Option FOR LG1152



THERMAL


FE_TS_DATA[5]

FE_TS_DATA[4]

FE_TS_DATA[2]

FE_TS_DATA[6]

FE_TS_DATA[7]

FE_TS_DATA[1]

FE_TS_DATA[0]

FE_TS_DATA[3]

C65260.1uF

16V

+5V_TU

C651910uF10V

DVB_S&CHB

C653622uF10V

C6522

0.1uF 16V

+3.3V_D_Demod

C65310.1uF

C65320.1uF

16V

LNB_TX

L6502BLM18PG121SN1D

T2/C&CN&BR

C65440.1uF16V

L9_T2/C/S

C6512100pF

DVB_S&CHB

/S2_RESET

CHB_DATA

L6503BLM18PG121SN1D

CHB_SYNC

C65160.1uF16V

T2/C&CHB&CN&BR

IF_AGC

I2C_SCL4

R6509

33

L6501BLM18PG121SN1D

DVB_S&CHB

C650618pF50V

OPT

C6514

0.1uF16V

I2C_SDA4

C651718pF50VOPT

+5V_TU

C65480.1uF16V

+5V_NORMAL

I2C_SDA6

+3.3V_TU

+1.8V_TU

L6507

BLM18PG121SN1D

CHB

C650110uF10V

CHB

+5V_TU

L6506BLM18PG121SN1D

NOT_T/C&AT

C654610uF10V

R6510

33

IF_P

+5V_TU

C65300.1uF16V

R6504 22

DVB_S&CHB

C6523100pF50V

CHB

CHB_CLK

R6503 22

DVB_S&CHB

C652922uF10V

C65250.1uF16V

OPT

C6524100pF

OPT

R651882

C6507100pF50V

T2/C&CHB&CN&BR

R652720K1%

NOT_T/C&AT

C65150.1uFDVB_S&CHB

R65250

NOT_L9_T2/C/S

L6508BLM18PG121SN1D

CHB

+3.3V_D_Demod

RF_SWITCH_CTL

C652810uF6.3V

OPT

R65311

C65134700pF50V CN

C651818pF50VOPT

R652910K1%

NOT_T/C&AT

R652310K

TU_TS_ERR

+1.23V_TU

+5V_NORMAL

+3.3V_D_Demod

C6511100pF50V

+3.3V_TU

R6506 100 T/C&AT&CHB

+1.23V_TU

C65390.1uF

16V

R652811K1%

NOT_T/C&AT

C650818pF50V

OPT

+3.3V_TU

C65090.1uF16VCHB

TU_CVBS

C65200.1uF16V

MTK/L9_DVB/ATSC/NTSC

+1.23V_TU

TU_TS_VAL

C653810uF10V

NOT_T/C&AT

+3.3V_TU

TU_TS_VAL

CHB_VAL

/TU_RESET

L6500BLM18PG121SN1D

FE_TS_VAL

FE_TS_DATA[0-7]

+3.3V_TU_IN

R65154.7K

FE_TS_CLK

0.1uFC6540

R65191K

OPT

R6508100

MTK/L9_DVB/ATSC/NTSC

IC6503

AZ1117BH-1.8TRE1

1

ADJ/GND

2 OUT3INC65420.1uF

NOT_T/C&AT

+3.3V_TU

C65101000pF50V CN

+1.8V_TU

R6500 0

RF_SWITCH

TU_TS_ERR

TUNER_SIF

C6549

10uF

16V

NOT_T/C&AT

I2C_SCL6

C65270.1uFOPT

+3.3V_TU

CHB_ERR

IC6501AP2132MP-2.5TRG1

EAN61387601

NOT_T/C&AT

3

VIN

2

EN

4

VCTRL

1

PG

5

NC

6

VOUT

7

ADJ

8

GND

9

[EP]

C65030.1uF16V

RF_SWITCH

C6533

10uF

16V

NOT_T/C&AT

LNB_OUT

IF_N

FE_TS_SYNC

CHB_CVBS

R6513

10DVB_S&CHB

R65122.2K

OPT

C65050.1uF16V

+3.3V_D_Demod

R6511100K

OPT

C65210.1uFOPT

+3.3V_NORMAL

+1.8V_TU

C6500

0.1uF16V

L9 ATSC

C653422uF10V

LNB_OUTLNB_TX CHB_CVBS

CHB_ERR

CHB_SYNC

CHB_VAL

CHB_CLK

CHB_DATA

ATV_OUT

ATV_OUT

C65351uFOPT

IC650074LVC1G08GW

L9_T2/C/S

3GND

2A

4Y

1B

5VCC

R6526100

L9_T2/C/S

1/16W5%

AR65020

NOT_T/C&AT&CHB

AR6500 0

NOT_T/C&AT&CHB

AR65010

NOT_T/C&AT&CHB

R6516470

Q6500MMBT3906(NXP)

E

B

C

Q6501MMBT3906(NXP)

E

B

C

R65320

NOT_L9_BR_TW_CN Tuner

C65500.1uF16V

C6551100pF50V

TU6500-*1TDSS-H151F

AT_H/NIM_V

5+B1[3.3V]

11DIF[N]

2RESET

10DIF[P]

4SDA

1NC

9IF_AGC

8CVBS

3SCL

7+B2[1.8V]

6SIF

12

SHIELD

TU6500TDSS-G151D

T/C_H/NIM_V

5+B1[3.3V]

11DIF[N]

2RESET

10DIF[P]

4SDA

1NC

9IF_AGC

8CVBS

3SCL

7+B2[1.8V]

6SIF

12

SHIELD

TU6503TDSQ-G051D

T/C/S2_V

1N.C_1

2RESET

3SCL

4SDA

5+3.3V_TUNER

6SIF

7+1.8V_TUNER

8CVBS

9T/C_IF_AGC

10T/C_DIF[P]

11T/C_DIF[N]

12N.C_2

13N.C_3

14N.C_4

15GND_1

16ERROR

17SYNC

18VALID

19MCLK

20D0

21D1

22D2

23D3

24D4

25D5

26D6

27D7

28GND_2

29GND_3

30+1.23V_S2_DEMOD

31S2_RESET

38

SHIELD

32+3.3V_S2_DEMOD

33S2_F22_OUTPUT

34S2_SCL

35S2_SDA

36LNB

37GND_4

TU6502TDSQ-H051F

CHB_V

1+5V[SPLITTER]

2RESET

3TU_SCL

4TU_SDA

5M_+3.3V

6M_SIF

7M_+1.8V

8M_CVBS

9M_IF_AGC

10M_DIF[P]

11M_DIF[N]

12S_3.3V

13S_1.8V

14S_CVBS

15GND_1

16SD_ERROR

17SD_SYNC

18SD_VALID

19SD_MCLK

20SD_SERIAL_D0

21N.C_1

22N.C_2

23N.C_3

24N.C_4

25N.C_5

26N.C_6

27N.C_7

28GND_2

29GND_3

30SD_1.23V_DEMOD

31SD_RESET

36

SHIELD

32SD_3.3V_DEMOD

33N.C_8

34SD_SCL

35SD_SDA

TU6503-*1

TDSQ-G351D

T2/C/S2

1N.C_1

2RESET

3SCL

4SDA

5+B1[3.3V]

6SIF

7+B2[1.8V]

8CVBS

9N.C_2

10N.C_3

11N.C_4

12+B3[3.3V]

13+B4[1.23V]

14N.C_5

15GND_1

16ERROR

17SYNC

18VALID

19MCLK

20D0

21D1

22D2

23D3

24D4

25D5

26D6

27D7

28GND_2

29GND_3

30+B5[1.23V]

31S2_RESET

38

SHIELD

32+B6[3.3V]

33S2_F22_OUTPUT

34S2_SCL

35S2_SDA

36LNB

37GND_4

TU6501-*1TDSN-B051F

BR_F/NIM_V

1RF_S/W_CTL

2RESET

3SCL

4SDA

5+B1[3.3V]

6SIF

7+B2[1.8V]

8CVBS

9NC_1

10NC_2

11NC_3

12+B3[3.3V]

13+B4[1.23V]

14NC_4

15GND

16ERROR

17SYNC

18VALID

19MCLK

20D0

21D1

22D2

23D3

24D4

25D5

26D6

27D7

28

SHIELD

TU6504TDSH-T151F

TW_H/NIM

5+B1[3.3V]

11DIF[N]

2RESET

10DIF[P]

4SDA

1RF_S/W_CTL

9IF_AGC

8CVBS

3SCL

7+B2[1.8V]

6SIF

12

SHIELD

TU6501TDSN-G351D

T2/C_F/NIM_DEV

1NC_1

2RESET

3SCL

4SDA

5+B1[3.3V]

6SIF

7+B2[1.8V]

8CVBS

9NC_2

10NC_3

11NC_4

12+B3[3.3V]

13+B4[1.23V]

14NC_5

15GND

16ERROR

17SYNC

18VALID

19MCLK

20D0

21D1

22D2

23D3

24D4

25D5

26D6

27D7

28

SHIELD

C6508-*168pF50V

BR_TW_CN_TUNERC6506-*168pF50V

BR_TW_CN_TUNER

R6500-*1

1K 5%

BR_TW_CN_TUNER

R6508-*1

1K 5%

BR_TW_CN_TUNER

R6532-*1BLM18PG121SN1D

L9/BR_TW_CN_TUNER

120-ohm

R6528-*112K

1/16W1%

CN

R6521220

R6520220

TU6501-*3TDSN-C051D

CN_LG3921

1RF_S/W_CTL

2RESET

3SCL

4SDA

5+B1[3.3V]

6SIF

7+B2[1.8V]

8CVBS

9NC_1

10NC_2

11NC_3

12+B3[3.3V]

13+B4[1.23V]

14NC_4

15GND

16ERROR

17SYNC

18VALID

19MCLK

20D0

21D1

22D2

23D3

24D4

25D5

26D6

27D7

28

SHIELD

TU6501-*2TDSN-C251D

CN_ATBM

1RF_S/W_CTL

2RESET

3SCL

4SDA

5+B1[3.3V]

6SIF

7+B2[1.8V]

8CVBS

9NC_1

10NC_2

11NC_3

12+B3[3.3V]

13+B4[1.23V]

14NC_4

15GND

16ERROR

17SYNC

18VALID

19MCLK

20D0

21D1

22D2

23D3

24D4

25D5

26D6

27D7

28

SHIELD

65

TUNER 2011.11.21

T2 : Max 1.7A

150mA(MAX)

close to TUNER

Vout=0.6*(1+R1/R2)

2. No via on both of them

Ground Width >= 24mils

1. should be guarded by ground

ERROR & VALID PIN

close to TUNER

RF_SWITCH_CTL USE: T2/C,T/C,ATSC,DTMB.ISDB-T

3. Signal Width >= 12mils

R2

2A

465mA(MAX)

should be guarded by groumd

T/C/S & H/NIM & T2/C TUNER(EU & CHINA)

R1

Signal to Signal Width = 12mils

else : Max 240mA

2012 perallel because of derating

else : Max 0.7A

CHB : Max 480mA

T/C_H/NIM T/C/S2 T2/C_F/NIM T2/C/S2 CHBAT_H/NIM CN

CHB CNDVB_S DVB_ST/C&AT&CHB T/C&AT&CHB

DVB_S&CHB DVB_S&CHB DVB_S&CHB

NOT_T/C&AT

NOT_T/C&AT

NOT_T/C&AT NOT_T/C&AT

NOT_T/C&AT

RF_SWITCH

T2/C

T2/C

T2/C&CN

T2/C&CHB&CN

T2/C&CN

T2/C&CHB&CN

T/C&AT&CHB

Close to the tuner

Close to the tunerClose to the tuner

close to TUNER

close to Tuner

Seperate GND for CHB

T/C&AT&CHB

T2/C&CHB&CNNOT_T/C&AT&CHBNOT_T/C&AT&CHB

NOT_T/C&AT&CHB

NOT_T/C&AT&CHB

H/NIM&CHB

NOT_DVB_S

NOT_DVB_S

NOT_DVB_S

NOT_DVB_S

BR

L9_T2/C/S

Not_L9_T2/C/S

Not_L9_T2/C/S

Not_L9_T2/C/S Not_L9_T2/C/S

Not_L9_T2/C/S

Not_L9_T2/C/S



THERMAL


A_GND

LNB_OUT

DCDC_GND

DCDC_GND

A_GND

A_GND

R690133

LNB

A_GND

+12V

LNB_TX

L6900

33UHSP-7850_33

LNB

R690033

LNB

C6907

0.22uF

LNB

A_GND

C69021uF50VLNB

+12V_LNB

DCDC_GND

C690668uF35VLNB

A_GND

I2C_SDA4

C6905 22000pF

LNB

I2C_SCL4

A_GND

R6903

4.7KLNB

D6901

40V

LNB_SMAB34

C69000.22uF25VLNB

C69010.01uF

50VLNB

D6903

40VLNB_SMAB34

L6901BLM18PG121SN1D

LNB

IC6900A8290SETTR-T

LNB

1BOOST

3TCAP

7TDI

9VREG

10

SDA

11

ADD

12

SCL

13

NC_2

14

IRQ

15 NC_3

16 NC_4

17 NC_5

18 NC_6

19 BFC

20 NC_7

21 NC_8

22

BFO

23

NC_9

24

BFI

25

VIN

26

LX

27

GNDLX

28

LNB

5TDO

8GND

6EXTM

4NC_1

2VCP 29

[EP]

C6908

27pF

OPT

C6903 0.1uF

LNB

C6909

27pF

OPT

D6902

40V

LNB_SMAB34

A_GND

+3.3V_NORMAL

DCDC_GND

A_GND

+12V_LNB

A_GND

C69110.1uF50V

LNB

C69040.1uF50VLNB

C691268uF35VLNB

D6900

30V

MBR230LSFT1G

LNB

R69062.2K1WLNB

D6904LNB

C691010uF25VLNB

R69040

R69050

C691618pFLNB

C691518pFOPT

C691333pFOPT

C691433pFLNB

D6901-*1

40V

LNB_SX34

D6902-*1

40V

LNB_SX34

D6903-*1

40VLNB_SX34

C69170.1uF50VLNB

C69180.1uF50VLNB

(Option:LNB)

DVB-S2 LNB Part Allegro DCDC_GND and A_GND are connected in pin#27

3A

Max 1.3A

PCB_GND and A_GND are connected

Input trace widths should be sized to conduct at least 3A

2A

DCDC_GND and A_GND are connected

2.4Aclose to Boost pin(#1)

Ouput trace widths should be sized to conduct at least 2A

close to VIN pin(#25)

69

LNB 2011.11.21

Close to Tuner

Surge protectioin




EXT_AMP_MUTE

AUDIO_L_OUT_COMMERCIAL

C70050.1uF 50V

+24V

+12V

C70040.1uF50V

R70001K

COMMERCIAL_12V_CTL

R7001100

IC7000MP5000DQ

3ENABLE/FAULT

2DV/DT

4I-LIMIT

1GND

5NC

6SOURCE_1

7SOURCE_2

8SOURCE_3

9SOURCE_4

10SOURCE_5

11

VCC

P7000

12507WR-12L

1

2

3

4

5

6

7

8

9

10

11

12

13

AUDIO_R_OUT_COMMERCIAL

EXT_AMP_RESET

12V_COMMERCIAL_OUT

SPK_L_OUT_COMMERCIAL

SPK_R_OUT_COMMERCIAL

L7000BLM18PG121SN1D

JK7000

KJA-PH-0-0177

EAG61030001

COMMER_EXT_AMP_JACK

3DETECT

4L

5GND

1RSPK_R_OUT_COMMERCIAL

SPK_L_OUT_COMMERCIAL

Q7001MMBT3904(NXP)

E

B

C

12V_EXT_PWR_DET

+3.5V_ST

C700222uF25V

R700522K

R7004100K

R700610K

C700322uF25V

C7000470pF50V

C70011uF25V

L7001BLM18PG121SN1D

D70005.6V

D70015.6V

C700710uF16V

C700610uF16V

70

COMMERCIAL_OPTION 2011.11.21

FOR AMP RESET (MAIN SOC)

FOR 12V CONTROL (FROM MICOM)

FOR COMMERCIAL 12V OUT RS-232C 9 PIN(OPT:COMMER_EXT_12V)

FOR COMMERCIAL AUDIO OUT(OPT:COMMER_EXT_AMP)

AUDIO OUT JACK(OPT:COMMER_EXT_AMP)

PATTERN SHOULD BE CONSIDERED (MAX 3W)




TXC3N

TXACLKN

C71020.1uF50VOPT

TXA0N

C710010uF16VOPT

TXC2N

TXCCLKP

TXA1P

TXBCLKN

PANEL_VCC

TXA2P

TXD3N

TXC2P

TXC4N

TXCCLKN

TXD4N

R7100 33

LGD_2D/3D_CTRL

R710310K

BIT_SEL_LOW

TXB1P

TXB2P

TXB0N

TXA4N

TXB4P

TXBCLKP

TXC0P

TXC1N

TXD2N

TXA1N

L7100

BLM18SG121TN1D

LVDS_51PIN

TXB1N

TXA3P

TXD0P

R7104 33

AUO_2D/3D_CTRL

TXD1P

TXA2N

TXA4P

TXD3P

TXB0P

TXB2N

TXB3N

TXA3N

TXC4P

R710210KLVDS_SEL_LOW

TXDCLKN

R7101

3.3KLVDS_SEL_HIGH

TXC1P

2D/3D_CTL

TXACLKP

2D/3D_CTL

TXB4N

TXA0P

TXB3P

TXC0N

TXD1N

+3.3V_NORMAL

TXD4P

TXDCLKP

TXD0N

TXC3P

C71011000pF50VOPT

TXD2P

P7100

FI-RE51S-HF-J-R1500

LVDS_51PIN

1NC

2NC

3NC

4NC

5NC

6AUO_65_MIRROR

7LVDS_SEL

8NC

9NC

10L/DIM_ENABLE

11GND

12RA0N

13RA0P

14RA1N

15RA1P

16RA2N

17RA2P

18GND

19RACLKN

20RACLKP

21GND

22RA3N

23RA3P

24RA4N

25RA4P

26GND

27BIT_SEL

28RB0N

29RB0P

30RB1N

31RB1P

32RB2N

33RB2P

34GND

35RBCLKN

36RBCLKP

37GND

38RB3N

39RB3P

40RB4N

41RB4P

42GND

43GND

44GND

45GND

46GND

47NC

48VLCD

49VLCD

50VLCD

51VLCD

52

GND

P7101

FI-RE41S-HF-J-R1500

LVDS_41PIN

1NC

2NC

3NC

4NC

5NC

6NC

7NC

8NC

9GND

10RC0N

11RC0P

12RC1N

13RC1P

14RC2N

15RC2P

16GND

17RCCLKN

18RCCLKP

19GND

20RC3N

21RC3P

22RC4N

23RC4P

24GND

25GND

26RD0N

27RD0P

28RD1N

29RD1P

30RD2N

31RD2P

32GND

33RDCLKN

34RDCLKP

35GND

36RD3N

37RD3P

38RD4N

39RD4P

40GND

41GND

42

GND

I2C_SDA1

I2C_SCL1

R7105 33

CP_BOXR7106 33

CP_BOX

PWM_DIM1

OPC_ENR7108 33

LGD_32/37_LVDS_OPC

R7107 33

LGD_32/37_LVDS_PWM

BIT_SEL

[51Pin LVDS OUTPUT Connector] [41Pin LVDS OUTPUT Connector]

LVDS

LVDS_SEL

71

LVDS_HIGH_MID 2011.08.11




I2C_SCL1

L/DIM0_SCLK

R760110KL/DIM_OUT

+3.3V_NORMAL

L/DIM0_MOSI

R76074.7K

L/DIM_OUT

R7606 33

L/DIM_OUT

P7600

12507WR-08L

L/DIM_OUT

1

2

3

4

5

6

7

8

9

I2C_SDA1

L/DIM0_VS

R760010KOPT AR7600

331/16W

L/DIM_OUT

LOCAL DIMMING

[To LED DRIVER]

76

LOCAL DIMMING 2011.12.13



THERMAL

THERMAL


VCOM_N

MCLK

DISCHG

R7709 0

1/16W

R7743 0

1/16WOPT

SWP

EO

C77501uF25VOPT

C771410uF25V

Vcore

C77571uF50V

VGH

GIP_RST

CLK3

R7701

10K

1/16W

VCOMRFB

VCOM

CLK5_I

VCOM_N

GST

R7745 0

1/16W

VCOM_P

C77310.1uF16V

GMA14

VGH_F

R7741 0

1/16WOPT

CTRLP

CLK1_I

VCOM_LOOP

VDD

VGH

VL

SWP

R77363K1/16W

VCOMLFB

R7708 0

1/16WC770510uF10V

R772601/16WOPT

VCC

R7706 47

1/16W

CLK2_I

VGL

VCC

CTRLP

TH770047k-ohm

NCP18WB473F10RB

I2C_SDA2

GMA12

VDD

GCLK

R773201/16WOPT

C771610uF25V

OPT

VGL_I

REVERSE

C77401000pF50V

OPT C77551uF50V

CLK2

SWN

VST

VDD

GMA7

C772310uF25V

C771310uF25V

CLK6

R7710 0

1/16W

C7748

1uF 25V

C7745

1uF 25V

R772101/16W

C7747

1uF 25V

R773301/16W

COMP

VCC

R7746 0

1/16W

C7721 10uF

25VOPT

C770910uF10V

CLK2_I

VGL

COMP

R771601/16WOPT

R7731 01/16W

SWN

VDD

R772301/16W

CLK4_I

R7742 3K

1/16WOPT

CLK3_I

RE

R7718

9.1K

1/16W

R77351001/16W

CTRLN

C771715pF50V

R77240

1/16WOPT

C770710uF10VOPT

VGL

VCOM_LOOP

R7704 47

1/16W

GMA4

CLK6_I

R77132.2

1/16WOPT

C771110uF10V

CLK6_I

L7702

22uH

VDD

VGH

SS

MCLK

DISCHG

R7703 47

1/16W

L7700

LQM2HPN2R2MG0L2.2uH

CLK4

R7722100K1/16W1%

SS

VL

H_VDD

C772510uF25V

OPT

C772015pF50V

VGH_R

VGL

R7719 0

1/16W

C7746

1uF 25V

CLK1

C77361000pF50V

CLK5_I

CLK5

TCOMP

EO

CLK1_I

VCC18

C770610uF10V

L7701

LQM2HPN2R2MG0L2.2uH

VCOM_P

PANEL_VCC

VGL

CLK4_I

C771915pF50V

R7734 0

1/16WOPT

C77040.1uF16V

GCLK

C77291000pF

50VOPT

R7705 47

1/16W

R7740 0

1/16W

I2C_SCL2C77421uF25V

GMA5

C771815pF50V

RE

CTRLN

VGH_EVEN

L770422uH

GST

C771010uF10V

TCOMP

PANEL_VCC

GMA15

CLK3_I

VGH_ODD

REVERSE

GST_SOC

GCLK_SOC

EO_SOC

MCLK_SOC

C77261uF25V

PANEL_VCC

R773801/16W

R774701/16WOPT

VCC

R77491K1/16WOPT

R77481K1/16W

R775115K1/16W

R775215K1/16W

R775415K1/16WOPT

R775315K1/16WOPT

C770810uF10VOPT

R77002K

1/16W

R7725 0

1/16W

OPT

C77241uF25V

VCOM_DYN

R772047K1/16W5%

R771733K1/16W

VGH_FB

VGL_FB

L7703NR6020T6R8NC

6.8uH

C771510uF16V

C772210uF16V

R77292.7K

1/16W

VCC

R7728 100K

1/16W 5%

R7730

1/16WOPT

R7737

1/16W

OPT

VGL_FB

R77391.5K1/16W5%

R7727 100K

1/16W 5%

VGH_FB

R7707

0

R7714

0

R77020

R7715

0

R7712

0

R7711

0

C77441uF50V

C77491uF50V

PMIC_RESET

D7703

100V

1N4148W

D7705

100V1N4148W

Q7701

MMBT3906(NXP)

E

B

C

D7704

100V

1N4148W

D7706

100V1N4148W

C772810uF10VOPT

C77121uF10V

C774110uF16V

EPI_LOCK6

EPI_LOCK6_SOURCE

+3.3V_NORMAL

C77320.1uF50V

C77270.1uF50V

C77540.1uF50V

Q7700MMBT3904(NXP)

E

B

C

D7700

40VSX34

D7701

40V

SX34

Q7702

MMBT3904(NXP)

E

B

C

Q7703MMBT3904(NXP)

E

B

C

R775810K

R775610K

R7757

10K

C77431uF25V

C77561uF25V

R77590

1/16W

R77600

1/16W

GMA18

VST

TXA1P

GMA1

EPI_LOCK3

CLK2

GIP_RST

VDD

TXB0P

CLK4

Vcore

GMA4

TXB2N

VCOMRFB

TXACLKP

VGL_I

GMA3

GMA4

EPI_LOCK3

CLK1

GMA16

GMA3

VGH_ODD

CLK1

GMA12

GMA9

Z_OUT

TXB2P

VGH_EVEN

CLK6

GMA9

VGH_EVEN

TXB1P

GMA5

GMA15

TXACLKN

GMA7

C77020.01uF

50V

GMA10

C77030.1uF

50V

VGH_ODD

VCC18

Vcore

VGL_I

GMA18

VCOM

GMA7

TXB0N H_VDD

GMA14

GMA10

VDD

TXA4N

CLK4

CLK5

CLK6

VGH_F

TXA1N

H_VDD

CLK3

VGH_R

Z_OUT

VST

GMA15

VCOMLFB

CLK5

CLK2

GMA16

VCOM

GMA5

GMA14

EPI_LOCK6_SOURCE

CLK3

TXB1N

VCC18

GMA12

VGH_F

GIP_RST

VGH_R

GMA1

TXA4P

C77000.01uF

50V

C77010.1uF

50V

R774420K1/10W5%

R775020K1/10W5%

C773310uF16V

R7755

100

P7702

FL8S050HA1

DEV_50WAFER

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

32

33

34

35

36

37

38

39

40

41

42

43

44

45

46

47

48

49

50

51

P7703

FL8S050HA1

DEV_50WAFER

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

32

33

34

35

36

37

38

39

40

41

42

43

44

45

46

47

48

49

50

51

C773068uF35V

C773568uF35V

C77340.1uF50V

C77370.1uF50V

C77390.1uF50V

C77380.1uF50V

R776110KOPT

VCC18

IC7700

TPS65178RSLREPI

1OUT4

2SWB4

3RST

4OUT1

5OUT2

6SWB2

7PGND2

8SWB1_1

9SWB1_2

10NC

11PVINB1_1

12PVINB1_2

13

AVIN

14

PVINB3

15

SWB3

16

OUT3

17

PGND3

18

PGND_1

19

PGND_2

20

SW_1

21

SW_2

22

SWI

23

SWO

24

AGND

25 SS26 COMP27 SCL28 SDA29 VL30 TCOMP31 CTRLP32 VGH33 SWP34 SWN35 VGL36 CTRLN

37

GMA1

38

GMA2

39

GMA3

40

GMA4

41

GMA5

42

GMA6

43

VCOM

44

NEG

45

POS

46

VCOMFB

47

DYN

48

PGND4

49

[EP]AGND

IC7701TPS65198

EPI

1CLK1

3CLK3

7RE

9VGH_F

10ODD

11EVEN

12VST

13RESET

14DISCHG

15

VGL

16

VGH1

17

VGH2

18

OUT

19

NEG

20

POS

21

AVDD

22 GND

23 VSENSE

24 EO

25 GST

26 MCLK

27 GCLK

28 BI-SCAN

5CLK5

8VGH_R

6CLK6

4CLK4

2CLK2

29

[EP]VGL

D7702

40VOPT

L7705BLM18PG121SN1DOPT

T-Con

<LEVEL SHIFTER BLOCK>

<POWER BLOCK>

77

2011.12.01

FROM SOC

FROM SOC

FROM SOC

FROM SOC

FROM SOC

TO SOC

INSTEAD OF AMCC0208

INSTEAD OF AMCC0209

[Right Source(41PIN LOCATION)][Left Source(51PIN LOCATION)]

THIS IS REVERSE PATTERN !!!!

FROM SOC

CH6

CH5

CH4FROM SOC

FROM SOC

FROM SOC




EMMC_DATA[5]

EMMC_DATA[0]

EMMC_DATA[2]

EMMC_DATA[1]

EMMC_DATA[4]

EMMC_DATA[7]

EMMC_DATA[3]

EMMC_DATA[6]

DAT4

DAT6

EMMC_RST

3.3V_EMMC

DAT5

DAT4

DAT5

C81040.1uF16V

R8116

10K

DAT3

EMMC_CMD

C81032.2uF10V

EMMC_VCCQ

EMMC_DATA[0-7]

C81062.2uF10V

EMMC_VCCQ

C810710pF50V

OPT

DAT6

C81020.1uF16V

DAT3

R8117

10K

C81050.1uF16V

EMMC_CLK

IC8100-*1H26M21001ECR

HYNIX_EMMC_2GB

DAT0A3

DAT1A4

DAT2A5

DAT3B2

DAT4B3

DAT5B4

DAT6B5

DAT7B6

CLKM6

CMDM5

NC_3A6

NC_4A7

NC_23C5

NC_42E5

NC_43E8

NC_44E9

NC_45E10

NC_52F10

NC_58G3

NC_59G10

NC_66H5

NC_73J5

NC_80K6

NC_81K7

NC_82K10

NC_116P7

NC_119P10

RESETK5

VCCQ_1C6

VCCQ_2M4

VCCQ_3N4

VCCQ_4P3

VCCQ_5P5

VCC_1E6

VCC_2F5

VCC_3J10

VCC_4K9

VDDIC2

VSS_1E7

VSS_2G5

VSS_3H10

VSS_4K8

VSSQ_1C4

VSSQ_2N2

VSSQ_3N5

VSSQ_4P4

VSSQ_5P6

NC_1A1

NC_2A2

NC_5A8

NC_6A9

NC_7A10

NC_8A11

NC_9A12

NC_10A13

NC_11A14

NC_12B1

NC_13B7

NC_14B8

NC_15B9

NC_16B10

NC_17B11

NC_18B12

NC_19B13

NC_20B14

NC_21C1

NC_22C3

NC_24C7

NC_25C8

NC_26C9

NC_27C10

NC_28C11

NC_29C12

NC_30C13

NC_31C14

NC_32D1

NC_33D2

NC_34D3

NC_35D4

NC_36D12

NC_37D13

NC_38D14

NC_39E1

NC_40E2

NC_41E3

NC_46E12

NC_47E13

NC_48E14

NC_49F1

NC_50F2

NC_51F3

NC_53F12

NC_54F13

NC_55F14

NC_56G1

NC_57G2

NC_60G12

NC_61G13

NC_62G14

NC_63H1

NC_64H2

NC_65H3

NC_67H12

NC_68H13

NC_69H14

NC_70J1

NC_71J2

NC_72J3

NC_74J12

NC_75J13

NC_76J14

NC_77K1

NC_78K2

NC_79K3

NC_83K12

NC_84K13

NC_85K14

NC_86L1

NC_87L2

NC_88L3

NC_89L12

NC_90L13

NC_91L14

NC_92M1

NC_93M2

NC_94M3

NC_95M7

NC_96M8

NC_97M9

NC_98M10

NC_99M11

NC_100M12

NC_101M13

NC_102M14

NC_103N1

NC_104N3

NC_105N6

NC_106N7

NC_107N8

NC_108N9

NC_109N10

NC_110N11

NC_111N12

NC_112N13

NC_113N14

NC_114P1

NC_115P2

NC_117P8

NC_118P9

NC_120P11

NC_121P12

NC_122P13

NC_123P14

EMMC_CLK_BALL

EMMC_CMD_BALL

EMMC_CMD_BALL

EMMC_CLK_BALL

EMMC_RESET_BALL

EMMC_RESET_BALL

EMMC_VDDI

EMMC_VDDI

DAT5

AR8100221/16W

AR8101221/16W

AR8102 22

R8100

10K

R8101

10K

R8102

10K

R8103

10K

R8104

10K

R8105

10K

R8106

10K

R8107

10K

IC8100-*3H26M31001EFR

DEV_HYNIX_EMMC_4GB

DAT0A3

DAT1A4

DAT2A5

DAT3B2

DAT4B3

DAT5B4

DAT6B5

DAT7B6

CLKM6

CMDM5

NC_3A6

NC_4A7

NC_23C5

NC_42E5

NC_43E8

NC_44E9

NC_45E10

NC_52F10

NC_58G3

NC_59G10

NC_66H5

NC_73J5

NC_80K6

NC_81K7

NC_82K10

NC_116P7

NC_119P10

RESETK5

VCCQ_1C6

VCCQ_2M4

VCCQ_3N4

VCCQ_4P3

VCCQ_5P5

VCC_1E6

VCC_2F5

VCC_3J10

VCC_4K9

VDDIC2

VSS_1E7

VSS_2G5

VSS_3H10

VSS_4K8

VSSQ_1C4

VSSQ_2N2

VSSQ_3N5

VSSQ_4P4

VSSQ_5P6

NC_1A1

NC_2A2

NC_5A8

NC_6A9

NC_7A10

NC_8A11

NC_9A12

NC_10A13

NC_11A14

NC_12B1

NC_13B7

NC_14B8

NC_15B9

NC_16B10

NC_17B11

NC_18B12

NC_19B13

NC_20B14

NC_21C1

NC_22C3

NC_24C7

NC_25C8

NC_26C9

NC_27C10

NC_28C11

NC_29C12

NC_30C13

NC_31C14

NC_32D1

NC_33D2

NC_34D3

NC_35D4

NC_36D12

NC_37D13

NC_38D14

NC_39E1

NC_40E2

NC_41E3

NC_46E12

NC_47E13

NC_48E14

NC_49F1

NC_50F2

NC_51F3

NC_53F12

NC_54F13

NC_55F14

NC_56G1

NC_57G2

NC_60G12

NC_61G13

NC_62G14

NC_63H1

NC_64H2

NC_65H3

NC_67H12

NC_68H13

NC_69H14

NC_70J1

NC_71J2

NC_72J3

NC_74J12

NC_75J13

NC_76J14

NC_77K1

NC_78K2

NC_79K3

NC_83K12

NC_84K13

NC_85K14

NC_86L1

NC_87L2

NC_88L3

NC_89L12

NC_90L13

NC_91L14

NC_92M1

NC_93M2

NC_94M3

NC_95M7

NC_96M8

NC_97M9

NC_98M10

NC_99M11

NC_100M12

NC_101M13

NC_102M14

NC_103N1

NC_104N3

NC_105N6

NC_106N7

NC_107N8

NC_108N9

NC_109N10

NC_110N11

NC_111N12

NC_112N13

NC_113N14

NC_114P1

NC_115P2

NC_117P8

NC_118P9

NC_120P11

NC_121P12

NC_122P13

NC_123P14

DUMMY_1DU1

DUMMY_2DU2

DUMMY_3DU3

DUMMY_4DU4

DUMMY_5DU5

DUMMY_6DU6

DUMMY_7DU7

DUMMY_8DU8

DUMMY_9DU9

DUMMY_10DU10

DUMMY_11DU11

DUMMY_12DU12

DUMMY_13DU13

DUMMY_14DU14

DUMMY_15DU15

DUMMY_16DU16

IC8100-*2KLM2G1HE3F-B001

SAMSUNG_EMMC_2GB

DAT0A3

DAT1A4

DAT2A5

DAT3B2

DAT4B3

DAT5B4

DAT6B5

DAT7B6

CLKM6

CMDM5

NC_3A6

NC_4A7

NC_23C5

NC_42E5

NC_43E8

NC_44E9

NC_45E10

NC_52F10

NC_58G3

NC_59G10

NC_66H5

NC_73J5

NC_80K6

NC_81K7

NC_82K10

NC_116P7

NC_119P10

RSTNK5

VDD_1C6

VDD_2M4

VDD_3N4

VDD_4P3

VDD_5P5

VDDF_1E6

VDDF_2F5

VDDF_3J10

VDDF_4K9

VDDIC2

VSS_1C4

VSS_2E7

VSS_3G5

VSS_4H10

VSS_5K8

VSS_6N2

VSS_7N5

VSS_8P4

VSS_9P6

NC_1A1

NC_2A2

NC_5A8

NC_6A9

NC_7A10

NC_8A11

NC_9A12

NC_10A13

NC_11A14

NC_12B1

NC_13B7

NC_14B8

NC_15B9

NC_16B10

NC_17B11

NC_18B12

NC_19B13

NC_20B14

NC_21C1

NC_22C3

NC_24C7

NC_25C8

NC_26C9

NC_27C10

NC_28C11

NC_29C12

NC_30C13

NC_31C14

NC_32D1

NC_33D2

NC_34D3

NC_35D4

NC_36D12

NC_37D13

NC_38D14

NC_39E1

NC_40E2

NC_41E3

NC_46E12

NC_47E13

NC_48E14

NC_49F1

NC_50F2

NC_51F3

NC_53F12

NC_54F13

NC_55F14

NC_56G1

NC_57G2

NC_60G12

NC_61G13

NC_62G14

NC_63H1

NC_64H2

NC_65H3

NC_67H12

NC_68H13

NC_69H14

NC_70J1

NC_71J2

NC_72J3

NC_74J12

NC_75J13

NC_76J14

NC_77K1

NC_78K2

NC_79K3

NC_83K12

NC_84K13

NC_85K14

NC_86L1

NC_87L2

NC_88L3

NC_89L12

NC_90L13

NC_91L14

NC_92M1

NC_93M2

NC_94M3

NC_95M7

NC_96M8

NC_97M9

NC_98M10

NC_99M11

NC_100M12

NC_101M13

NC_102M14

NC_103N1

NC_104N3

NC_105N6

NC_106N7

NC_107N8

NC_108N9

NC_109N10

NC_110N11

NC_111N12

NC_112N13

NC_113N14

NC_114P1

NC_115P2

NC_117P8

NC_118P9

NC_120P11

NC_121P12

NC_122P13

NC_123P14

C81000.1uF16V

OPT

IC8100SDIN5D2-4G-974L1

SANDISK_EMMC_4GB

DAT0A3

DAT1A4

DAT2A5

DAT3B2

DAT4B3

DAT5B4

DAT6B5

DAT7B6

CLKM6

CMDM5

NC_3A6

NC_4A7

NC_23C5

NC_42E5

NC_43E8

NC_44E9

NC_45E10

NC_52F10

NC_58G3

NC_59G10

NC_66H5

NC_73J5

NC_80K6

NC_81K7

NC_82K10

NC_116P7

NC_119P10

RESETK5

VCCQ_1C6

VCCQ_2M4

VCCQ_3N4

VCCQ_4P3

VCCQ_5P5

VCC_1E6

VCC_2F5

VCC_3J10

VCC_4K9

VDDIC2

VSS_1E7

VSS_2G5

VSS_3H10

VSS_4K8

VSSQ_1C4

VSSQ_2N2

VSSQ_3N5

VSSQ_4P4

VSSQ_5P6

NC_1A1

NC_2A2

NC_5A8

NC_6A9

NC_7A10

NC_8A11

NC_9A12

NC_10A13

NC_11A14

NC_12B1

NC_13B7

NC_14B8

NC_15B9

NC_16B10

NC_17B11

NC_18B12

NC_19B13

NC_20B14

NC_21C1

NC_22C3

NC_24C7

NC_25C8

NC_26C9

NC_27C10

NC_28C11

NC_29C12

NC_30C13

NC_31C14

NC_32D1

NC_33D2

NC_34D3

NC_35D4

NC_36D12

NC_37D13

NC_38D14

NC_39E1

NC_40E2

NC_41E3

NC_46E12

NC_47E13

NC_48E14

NC_49F1

NC_50F2

NC_51F3

NC_53F12

NC_54F13

NC_55F14

NC_56G1

NC_57G2

NC_60G12

NC_61G13

NC_62G14

NC_63H1

NC_64H2

NC_65H3

NC_67H12

NC_68H13

NC_69H14

NC_70J1

NC_71J2

NC_72J3

NC_74J12

NC_75J13

NC_76J14

NC_77K1

NC_78K2

NC_79K3

NC_83K12

NC_84K13

NC_85K14

NC_86L1

NC_87L2

NC_88L3

NC_89L12

NC_90L13

NC_91L14

NC_92M1

NC_93M2

NC_94M3

NC_95M7

NC_96M8

NC_97M9

NC_98M10

NC_99M11

NC_100M12

NC_101M13

NC_102M14

NC_103N1

NC_104N3

NC_105N6

NC_106N7

NC_107N8

NC_108N9

NC_109N10

NC_110N11

NC_111N12

NC_112N13

NC_113N14

NC_114P1

NC_115P2

NC_117P8

NC_118P9

NC_120P11

NC_121P12

NC_122P13

NC_123P14

DUMMY_1DU1

DUMMY_2DU2

DUMMY_3DU3

DUMMY_4DU4

DUMMY_5DU5

DUMMY_6DU6

DUMMY_7DU7

DUMMY_8DU8

DUMMY_9DU9

DUMMY_10DU10

DUMMY_11DU11

DUMMY_12DU12

DUMMY_13DU13

DUMMY_14DU14

DUMMY_15DU15

DUMMY_16DU16

R8103-*1

47K

R8104-*1

47K

R8105-*1

47K

R8106-*1

47K

R8100-*1

47K

R8102-*1

47K

R8107-*1

47K

R8101-*1

47K

11.09.29

81

eMMC

eMMC I/F

Don’t Connect Power At VDDI

(Just Interal LDO Capacitor)

EMMC DATA LINE 47K PULL/UP

EMMC DATA LINE10K PULL/UP




+3.5V_ST

L8900

BLM18PG121SN1D

LOGO_LIGHT P8900

12507WR-03L

LOGO_LIGHT1

2

3

4

Q8900

MMBT3904(NXP)

LOGO_LIGHT

E

B

C

LOGO_LIGHT

R89031K

LOGO_LIGHT

+3.5V_ST

R8901

10K

LOGO_LIGHT

R8902

10K

OPT

C89000.1uF16V

LOGO_LIGHT

R8900

22LOGO_LIGHT

Place Near Micom



2012 LED/LCD TVEngineering guide

< Applicable Model >XXLM760S-ZB



CONTENT

New features Main PCBs Block Diagrams, IIC Map Structure of TV set and connection of sub ass’ysNew sub ass’ys- Instruction of new sub ass’ys- How to use tool- Download

Adjust way of new features (widevine…) Repair guide The latest issue and concerning issue



EPI Interface

EPI(Embedded Point-Point Interface)

Features• Point-Point topology (support 2 Pair option)• CDR (Clock Data Recovery)• Bandwidth up to 1.85Gbps/pair

at FHD 120Hz 10 bit application• Lock signal cascading and feedback to T-Con• Embedded Control Data

Merits• Better reliability on common noise• No data skew and better EMI margin• Fewer lines than mini-LVDS• Slim PCB design

TCON

2

LOCK

VCC 1

Figure1. Topology



EPI Interface (mini-LVDS vs. EPI)

Comparison

HF mini-LVDS

What to change

EPI (Embedded clock P-to-P Interface)

-Difficult to upgrade bandwidth limit-Multiple number of wires needed for higher bandwidth

HF mini- LVDS

FHD (10bit)60Hz 120Hz 240Hz

No. of Signal 36 36 72

Connector 60pin(2ea)

60pin(2ea)

80pin(2ea)

-Better reliability on common noise-No data skew. Better EMI margin-Lower cost ( Cable, Connector )-Slim S-PCB design (14mm 10mm) helps slimmer TV

EPIFHD (10bit)

60Hz 120Hz 240Hz960ch 960ch 720ch

No. of Signal 12 12 32

Connector - 50 pin (2ea)

70pin (2ea)

LCM (T-con to S-Driver IC)

TCON

2

LOCK

VCC 1

TCON

18

VCC 1

18

HF mini-LVDS

EPI

* Bandwidth Capability - FHD 120Hz 10Bit : 594Mbps@36Lines → 1.65Gbps@12Lines- FHD 240Hz 10Bit : 594Mbps@72Lines → 1.25Gbps@32Lines

(FHD 120Hz)

(FHD 120Hz)



HF mini-LVDS EPI

Topology

Protocol

Features@10bit, FHD120

• Multi Drop• Data rate: 660Mbps• External clock

• Point to Point• Data rate : 1.8Gbps• Embedded clock, Control

Merit• Simple structure• Standardization

• Fewer Lines : 12• Embedded clock

: low EMI, Clock skew free• Easy to PCB design

Demerit

• Too many lines : 36• Clock skew• EMI due to clock lines• Bandwidth limit

• Transmission Overhead: 4bit delimiter

TCON

Lock

21

TCON

EPI Interface (mini-LVDS vs. EPI)



Main PCB for Broadband Main + TCON all in one

To PSU

1

2

6

4

1 Main processor, DDR MemoryeMMC Memory

2

3

4

Micom for Key/IR sensing

PMIC

Audio AMP (10W+10W)

xxLM760S-ZB

Soft touch +IR

Front Spk

To module

5

5 EPI Wafer

G/S model

21

LNB IC Only G/S model

1

2

Chassis : LD22EPCB P/No : EAX64307905

3

6 Level shifter

WIFI

RF Assy



MTK5369 Block Diagram( LM76 )

L/R In

SPDIF OUT

USB

AudioAMP

(NTP7500 or STA)

I2S OutMTK

CI slotCI slot

P_TS

CVBS

P_TS

T/C DemodIF(+/-)

USB1

RS-232C

PC-RGB

PC-AUDIO

OPTIC

LAN

SYSTEMDDR3 X

1600 X 16 (2Gb)

HDMI1

HDMI2

HDMI3

Side

RearRGB,H/V

Ethernet

CVBS

UART

SYSTEM EEPROM X 1(256Kb)

HDMIMUX

(HDCPEEPROM)

M-Remote Module

Air/Cable

TUNER(T/C)

TUNER(S2)

DIGITALDEMOD

(T/C)

DVB-S

ANALOGDEMOD

DIGITALDEMOD

(S2) TS_S/P

LNB

USB2USB3

HDMI4 LVDS 41P51P

eMMC X 1(4GB)

USB_WIFI

SYSTEMDDR3 X

1600 X 16(2Gb)

DDR CONTROLER A/B

SPI LOCAL DIMMING

I2C Sub Micom (RENESASA)

IR Remote Control

SYSTEMDDR3 X

1600 X 16 (2Gb)

SYSTEMDDR3 X

1600 X 16(2Gb)

UART

P_TS

Power load

EPI50P50P

X_TAL27MHz



Jack Interface

[PR0P],[PB0P],[Y0P]

[OPCTRL8]

[VDACX_OUT][VDACY_OUT]

[AUOUTL0]

[ADIN0_SRV]

[CVBS2P]

[AIN0_L_ADDC][AIN0_R_AADC]

[SPDIF_OUT]

[AUOUTR0]

Main SoCMTK

[SOY0]

[Y1P],[PB1P],[PR1P]

[OPCTRL9]

[AL0_ADAC][AR0_ADAC

[VGA_SCL]

[VGA_SDA]

[OPCTRL7]

[VSYNC], [HSYNC]

[RP],[GP],[BP]

[ASPDIF0] SPDIFSPDIF_OUT

[AIN2_L_AADC]

COMP 1 PHONE JACK

COMP1_Y/Pb/Pr COMP1_DET

SC_DET

SC_R/G/B +

SC_ID

DTV/MNT_V_OUT

DTV/MNT_L_OUT IC6000AZ4580M

SC_L/R_IN

SC_CVBS_IN

[SCART_LOUT][SCART_ROUT]DTV/MNT_R_OUT

SC_FB

[AIN3_R_AADC][AIN3_L_AADC]

[CVBS0P]

[OPCTRL5]

AV1_L_INAV1_R_IN

AV1_CVBS_DET

AV1_CVBS_IN

CVBS 1 PHONE JACK

EARPHONEJACK

HP_LOUT_MAIN

HP_ROUT_MAIN

RGB_PC

RGB_DDC_SCL

RGB_DDC_SDA

DSUB_DET

DSUB_VSYNC, DSUB_HSYNC

DSUB_R+, DSUB_G+, DSUB_B+

PC AUDIOPC_L_INPC_R_IN

[AIN2_R_AADC]

Full Scart(18 Pin Gender)

IC6100TPA6132A2

HP_LOUT_AMP

HP_ROUT_AMP



GP4 Backend block diagram (EPI & T-con)

IC7700TPS65178

IC7701TPS65198

50PinEPI LEFT

50PinEPI RIGHT

VCOM, GIP_RST

R(0옴)OPT

DISCHG VGL_I

VG

L_I

VGH_ODD, VGH_EVEN

VGH_R, VGH_F, VST

R(0옴)

CLK1~6_I CLK1~6

VCO

M_P

/N/L

OO

P

VGL_FB

CTRLN

VCC

CTRLP

VGH_FB

VDD

SWP

SWN

Main SoCMTK

R(47옴)

EO_SOC

MCLK_SOC

GST_SOC

GCLK_SOC GCLK

MCLK

GST

EO[TCON6]

[TCON5]

[TCON4]

[TCON3]



GP4 Backend block diagram (EPI & T-Con)

Main SoCMTK IC7700

TPS65178

50PinEPI LEFT

50PinEPI RIGHT

GM

A[1][3][9][10][12][14][15][16][18]

GMA[4][5][7][12][15]

EPI_LO

CK3

TXA1N/P, TXACLKN/P, TXA4N/PEPI CH1/2/3

EPI CH4/5/6

TXA0N/P, TXB1N/P, TXB2N/P

Z_OU

T

Vcore

VDD

H_VDD

Vcore

H_VDD

VDD

VCC18

VCC18

VCOMLFB

VCOMRFB

EPI_LOCK6

EPI_LOCK6_SOURCE

VCOM_DYN

PMIC_RESET

I2C_SDA2

I2C_SCL2

[TCON7]

[TCON8]

[OPCTRL11]

[OPCTRL10]



GP4 Backend block diagram (LVDS Tx & Local Dimming)

LVDS Tx Block

Main SoCMTK

LVDS_SEL

BIT_SEL_LOW

51PinLVDS

Output

PANEL_VCC (+12V)

41PinLVDS

Output

10-bit (R)

Dual-link LVDS Output24

10-bit (R)24

Dual-link LVDS Output

• LVDS_SEL : “H”=JEIDA, “L” or NC=VESA (LGD)• BIT_SEL : “H” or NC = 10-bit, “L” = 8-bit

L/DIMO_SCLK

L/DIMO_MOSI

I2C_SCL1

I2C_SDA1

L/DIMO_VS

[LDM_CK]

[LDM_VSYNC]

[STB_SCL]

[LDM_D0]

[STB_SDA]



Interconnection - 1

1 Main PCB

2 Power Board

3 Tact key PCB

T-con Driver

1

2

3

4

5

Main / LPB 24Pin cable Main / Module EPI cable 50& 50PIN

LED driver / PSU

10Pin (IR+Touch) Cable

SPK Cable

Local Dimming Cable

[PCBs]

[Cables]

6

12

3

1

2

3

4

5

6

xxLM760S-ZA

7

RF Assy Cable7

8

WIFI Assy Cable8

45

4 RF Assy

5 WIFI Assy



2012Y IR + Soft touch PCB Pinmap

Circuit Block Diagram

Pin Configuration

KEY1, KEY2 Voltage(Tolerance of voltage ±0.2V)

Ass’y Picture



2012Y IR + Soft Touch LED Lighting Scenario

구분 Spec 내용 비고

PowerIndicator UI

- 12Y GP4 High(L9), GP4 Mid(MTK), GP4 Low(S7LR2)“ Power Light” UI Delete compared with 11Y(GP3 model)

- 11Y Carry Over Model : 12Y same Power LED scenario process“ Power Light “ UI Delete, The way of 11Y Soft Touch Ass’y is used. White LED Disable

-

GP4(High/Mid/Low)

Power LEDScenario

UserCondition

Power On- Stand-By condition to Red LED On : After DC ON, Red LED light Blinks twice and then Red LED is Off- Stand-By condition to Red LED Off : After DC ON, Red LED light Blinks three times and then Red LED is Off

-

Power Off- Without Blink, Red LED On immediately

But, If the mode of Power Indicator UI is Stand-By, keep staying Red LED Off status-

Remote Keyinput

- When you put the remote Control button, Red LED Blinks once -

WarmStand-by

- Red LED On stays and In the case of Set On, Red LED turns OffIncluding DVR Ready model, Japanese model

Same as the 11Y

3D mode - Red LED Off (Power On condition is identical)Same as the 11Y

FactoryCondition

FactoryDefault Mode

(In-Stop)

- 12Y LED Model : Stand-By On (Red LED On)- 12Y CCFL Model : Stand-By On (Red LED On)- 11Y Carry Over Model (CS5XX/CM5XX) : Stand-By On (Red LED On)- After In-Stop, Red LED On is processed and after In-Stop, Red LED turns on within 3 sec

-

Power OnlyMode

- In the case of Power Only On, Red LED turns Off- In the case of DC Off, Red LED turns On

-

Power LED Scenario



Introductions of GP4 Sensor (Touch IC)

Touch Key Threshold Level (Ta = 25ºC )

1. Verify the number of THR at first.

2. Once you correctly touch Touch button for more than 1 sec, you can see a Touch data while you keep touching the button.

3. Keep in mind that you can only read the Touch data during touch status.

4. It doesn’t matter that Touch data gets low value after taking off your finger.

Manual of Touch Sensitivity



Introductions of GP4 Sensor (Touch IC)

Touch EEPROM Register change with USB port1. Write all of the address, value (Hex) as a below. capable of only Touch.txt file based on the left picture

2. Make the file [ Filename : ‘Touch.txt’ ] and move it to USB (The outermost area, Don’t move it to any folder)

3. Connect USB to TV and press button ‘ADJ menu’ and then choose the ‘touch sensitivity setting’

4. Press button ‘SIMPLINK (Simply Link key)’ and then you can see the OK Pop up.

5. After that, you check it the IR LED version on In-start menu and verify it that the number of version is changed to what you want.

Addr Value



Introductions of 12Y RF ass’y + Magic Remote control



1. System

Remote RF Receiver TV

UART or USBRF

Pairing Information Transmission (Send to TV after Paired)• Static Calibration Data (Bypass only)• Remote FW ver. (Save also in Receiver)• BD_ADDR (Save also in Receiver)

• Pairing Information Transmission Sequence• When it is paired, the remote sends packets(pairing success, F/W version, BD_ADDR) to the receiver.• The receiver sends the pairing success packet to TV directly.• F/W version and BD_ADDR packets are just saved on the receiver. • The receiver sends F/W version or BD_ADDR packet to TV when it is required.

Motion Data Transmission• Period : 7.5msec• Motion Data : gyro, accelerometer

Voice Data Transmission• Period : 10msec• Voice sampling : 16khz 16bit

See “6-2. Packets” on page 8.



2. Remote Buttons (M3 vs. M4)

BUTTONRF Unpaired

IR_CODERF PairedRF_CODE

IR continuousrepeat

ETC.

Phsical Buttons

POWER 0x08 0x08 Y IR onlyBACK 0x28 0x8028 YHOME 0x7C 0x807C Y← 0x07 0x8007 Y→ 0x06 0x8006 Y↑ 0x40 0x8040 Y↓ 0x41 0x8041 YOK 0x75 0x8044 YCH + 0x00 0x8000 YCH - 0x01 0x8001 YVOL + 0x02 0x8002 YVOL - 0x03 0x8003 YMUTE 0x09 0x8009 Y .3D_Mode 0xDC 0x80DC YMyAPPS 0x42 0x8042 YVOICE 0x800A Y = VOICE_START

LogicalButtons

AUTO_WAKEUP X 0x800CVOICE_START X 0x800AVOICE_STOP X 0x800DPOINT_START X 0x803EPOINT_STOP X 0x803F

powermutehome

↑

ok← →

↓

voice

vol ch

M3 Remote M4 Remote

powerback home

↑

ok← →

↓

mutevol ch

3D star



MPU-3050 (Gyro)(Invensense)

LIS331DLH(Accel.)(STMicro) BCM20733M

(BROADCOM) Bluetooth 3.0

Key Button( 4 x 5 )

AA x 2 Battery DC-DC 2.8V LDO

Power Management

Bluetooth Remocon Bluetooth Receiver

BCM20702M(BROADCOM)Bluetooth 4.0

Antenna

Connector

X-tal20 MHz

Antenna

X-tal24 MHz

3. M4 Block Diagram

2.8V LDO

256Kbit(E2PROM)

512Kbit(Serial Flash)

I2C

I2C

SPI

UART

SPI

WM8950(Wolfson)

Voice

MIC.(Knowles)

I2S

M4 4-mode Only



주요 Item IC Manufacturer Function

Remocon

VoiceVoice Codec WM8950 Wolfson 16KHz Sampling of Audio data

MEMS Mic. SPU0414HR5H Knowles Sensing Voice

Motion Sensor

Gyro Sensor ITG3050 Invensense Sensing angular velocity of X, Y, Z-axis

Accelerometer MMA8452 Stmicro Sensing device tilt (Pitch & Roll angle)

RF+

Micom

RF Antenna SDBTPTR3015 Partron

Wireless communicationX-tal 24MHz Partron

RF + Micom BCM20733 Broadcom

DC-DC Converter TPS61097 TI Battery Boost up Regulator

LDO1 uPI7716 uPI RF, Gyro, Accelerometer Power Supply

LDO2 uPI7716 uPI Audio Codec, Mic. Power Supply

4. Function list



5. RF Pairing / Un-pairing Method

Method Description

RF Pairing

Method1– If unpaired, just press "OK" button.– If paired, press "OK" button after

unpairing.Method 2 (Repairing)

– Press “BACK" button for 5 sec.

• When do pairing, the remote should make pairing request IR signal(0x29) to TV.

• When TV receive the IR signal, it should send "pairing request packet" to the RF receiver.

• After pairing success, the remote should blink LED for some time and TV send "pairing success packet" back to TV.

• When remote try to unpairing, it doesn’t care about state of receiver(stand alone).

RF Unpairing Press “HOME" button and “BACK" button at the same time for 5 sec.

• When remote try to unpairing, it doesn’t care about state of receiver(stand alone).

• After unpairing, all pairing information should be erased.

• After unpairing, LED should be blinked for 3sec.

• The remote just becomes to IR mode.



Introductions of 12Y WIFI built in ass’y



WIFI Built in ass’y feature(LGIT)

WIFI built in feature

PIN USB interface

1 5V

2 DM

3 DP

4 GND

- Pin map

- Block diagram



WIFI Built in Block-diagram(Arcadyan)



WIFI Built in ass’y Specification



12Y Widevine & HDCP 2.0 & NETFLX

1. Widevine?2. HDCP 2.0 & NETFLIX?3. DTCP?4. Changed BOM



1. Widevine?

[Widevine]

Widevine is the Solution(Library) offering Adaptive Streaming and DRM.In BBTV, when special CP do service, this module is required key.Currently CP which is requested to widevine, is typically Australian Bigpond Live and North American CinemaNow. Furthermore, because the future will be the spread of CP, widevine key download for the global model should be applied to production. (Because operation unique key should be downloaded for Widevine , Widevine key dowmload by NSU is impossible.)

[Widevine]

Widevine is the Solution(Library) offering Adaptive Streaming and DRM.In BBTV, when special CP do service, this module is required key.Currently CP which is requested to widevine, is typically Australian Bigpond Live and North American CinemaNow.Furthermore, because the future will be the spread of CP, widevine key download for the global model should be applied to production.(Because operation unique key should be downloaded for Widevine , Widevine key dowmload by NSU is impossible.)

[Widevine Key]Widevine Key is unique data stored TV for using Widevine.[Widevine Key]Widevine Key is unique data stored TV for using Widevine.



HDCP

High-bandwidth Digital Content Protection

Protect high-value digital motion pictures, television programs and audio against unauthorized interception and copying between a digital set top box or digital video recorder and a digital TV or PC.

Specification developed by Intel Corporation to protect digital entertainment across the DVI/HDMI interface.

Why HDCP2.0?

HDCP revision 2.0 supports a broader range of wired and wireless interfaces.

Netflix

the services maintain a huge selection of movies and latest releases and offer DVD rentals via mail & online streaming.

2. HDCP 2.0 & NETFLIX?



3. DTCP?

[DTCP]

The Digital Transmission Content Protection Specification defines a cryptogrphic protocol for protecting audio/video entertainment content from unauthorized copying, intercepting, and tampering as it traverses digital transmission mechanisms such as a high-performance serial bus that conforms to the IEEE 1394-1995 standard. Only legitimate entertainment content delivered to a source device via another approved copy protection system (such as the DVD Content Scrambling System) will be protected by this protection system.

[Three cryptographic Keys]

• Authentication Key which is formed as a result of authentication and used to protect the exchange keys.

•Exchage Key which is used to set up and protect content streams.

•Content Key which is used to encrpt the content being exchanged.

[DTCP]

The Digital Transmission Content Protection Specification defines a cryptogrphic protocol for protecting audio/video entertainment content from unauthorized copying, intercepting, and tampering as it traverses digital transmission mechanisms such as a high-performance serial bus that conforms to the IEEE 1394-1995 standard. Only legitimate entertainment content delivered to a source device via another approved copy protection system (such as the DVD Content Scrambling System) will be protected by this protection system.

[Three cryptographic Keys]

• Authentication Key which is formed as a result of authentication and used to protect the exchange keys.

•Exchage Key which is used to set up and protect content streams.

•Content Key which is used to encrpt the content being exchanged.



4. Changed BOM

As-Was Current

추가

Add Item1.Marlin (Yes/No)2.CNTV (Yes/No)3.HDCP Tx (Yes/No)4.DTCP Rx (Yes/No)5.HDCP Rx (Yes/No)주3) CNTV [Yes] : China Smart TV Only



4. Changed BOM



Contents of LCD TV Standard Repair Process

No. Error symptom (High category) Error symptom (Mid category) Page Remarks

1

A. Video error

No video/Normal audio 1

2 No video/No audio 2

3 Video error, video lag/stop, fail tunning 3, 4

4 Color error 5

5Vertical/Horizontal bar, residual image, light spot, external device color error

6

6

B. Power error

No power 7

7Off when on, off while viewing, power auto on/off

8

8C. Audio error

No audio/Normal video 9

9 Wrecked audio/discontinuation/noise 10

10D. Function error

No response in remote controller, key error, recording error, memory error

11

11 External device recognition error 12

12 E. Noise Circuit noise, mechanical noise 13

13 F. Exterior error Exterior defect 14

First of all, Check whether there is SVC Bulletin in GCSC System for these model.



Contents of LCD TV Standard Repair Process Detail Technical ManualNo. Error symptom Content Page Remarks

1

A. Video error_ No video/Normal audio

Check LCD back light with naked eye A1

2 LED driver B+ 24V measuring method A2

3 Check White Balance value A3

4 Power Board voltage measuring method A4

6A. Video error_ No video/Video lag/stop

TUNER input signal strength checking method A6

7 LCD-TV Version checking method A7

9

A. Video error_Color error

LCD TV connection diagram A8

10 Tuner Checking Part A9

11 Check Link Cable (LVDS) reconnection conditionA10A11

A10 : 32/37/42/47/55A11 : 32 AUO

12 Adjustment Test pattern - ADJ Key A12

13

A. Video error_Vertical/Horizontal bar, residual image, light spot

LCD TV connection diagram A8

14 Check Link Cable (LVDS) reconnection conditionA10A11

A10 : 32/37/42/47/55A11 : 32 AUO

15 Adjustment Test pattern - ADJ Key A12

16

<Appendix>Defected Type caused by T-Con/ Inverter/ Module

Exchange T-Con Board (1) A-1/5

17 Exchange T-Con Board (2) A-2/5

18 Exchange LED driver Board (PSU) A-3/5 55” : driver boardOther : PS

19 Exchange Module itself (1) A-4/5

20 Exchange Module itself (2) A-5/5

Continue to the next page



Normal audio

Y

N

Move to No video/No audio

No videoNormal audio

Check Back LightOn with naked eye On

Y

N

Check Power Board12v,3.5v etc.

Normal voltage

Y

N

Replace T-con Board or moduleAnd Adjust VCOM

Repair Power Board or parts

Check Power Board 24v output

Normalvoltage

Y Replace Inverter or module

NRepair Power Board or parts

End

Always check & record S/W Version and White Balance value before replacing the Main Board Replace Main Board Re-enter White Balance value

※Precaution

Establisheddate

Standard Repair Process

Revised date 1/13LCD TV Error

symptomA. Video error

No video/ Normal audio

A4A1

A2A28

A7 & A3

First of all, Check whether all of cables between board is inserted properly or not.(Main B/D↔ Power B/D, LVDS Cable,Speaker Cable,IR B/D Cable,,,)

2010. 12 .14



Normalvoltage?

Check various voltages of Power Board ( 3.5V,12V,20V or 24V…)

No Video/No audio

Check and replace MAIN B/D

Y

Replace Power Board and repair parts

N End


A. Video errorNo video/ No audio

A4

Establisheddate


symptom2010. 12 .14



A. Picture ProblemPicture broken/ Freezing

Y

N

A6

N

Check RF Signal level

Normal Signal?

Check RF Cable Connection

1. Reconnection2. Install Booster

CheckS/W Version

Booster menuOn→Off: CheckOff→On: Check

S/W Upgrade

Check whether other equipments have problem or not.(By connecting RF Cable at other equipment)

→ DVD Player ,Set-Top-Box, Different maker TV etc`

SVC Bulletin?

ReplaceMain B/D

CheckTuner soldering

Normal Picture?

Y

N

Y

Close

Normal Picture?

YClose

Menu→Setup →Booster

. By using Digital signal level meter

. By using Diagnostics menu on OSD( Menu→ Set up→ Support → Signal Test )- Signal strength (Normal : over 50%)- Signal Quality (Normal: over 50%)

Normal Picture?

Y

Contact with signal distributoror broadcaster (Cable or Air)

N N

Normal Picture?

Y

Close

N

A7


Establisheddate


symptom2010. 12 .14



A. Picture Problem (DVB-S/S2)Tuning fail, Picture broken/ Freezing

Y N

A6Check RF Signal level

Normal Signal?

CheckS/W Version

S/W Upgrade

SVC Bulletin?

Normal Picture?

Y

N

Y

Close

Check RF signal cable (DVB satellite signal or not)Check whether other equipments have problem or not.(By connecting RF Cable at other equipment)→ Set-Top-Box, Different maker TV etc

Y

Change satellite setting(match with installed ANT)

N

Normal Picture?

Y

Close

N

A7


Establisheddate


symptom2011. 01 .24

Check satellite setting.- Check LNB frequency.- Check satellite - Check Satellite connection

(DiSEqC, motor, etc…)

Normal setting?

Contact with signal distributor

or broadcaster (Cable or Air)

Close

N

CheckTuner soldering

ReplaceMain B/D



Colorerror?

Y

N

※ Check and replace Link Cable(LVDS) and contact condition

Y

N

Replace Main B/DColorerror?

Check error color input mode

Check color by input-External Input-COMPONENT-RGB-HDMI/DVI

YExternal device/Cablenormal

External Input/Component

error

Check external device andcable

YExternal device/Cablenormal

RGB/HDMI/DVI

error

Check external device and cable

Replace Main B/D

Replace Main B/D

N

N

A. Video errorColor error

A8

N

Y

End

Replace module

Request repair for external device/cable

Colorerror?

Check Test pattern

A12

A10/ A11


Establisheddate


symptom2010. 12 .14



Screennormal?

N

YCheck external device connection condition

Y

N

Check and replace Link Cable

Normal?

Y

NScreennormal? Replace Main B/D

(adjust VCOM)

Replace module

Check color condition by input-External Input-Component-RGB-HDMI/DVI

End

Vertical/Horizontal bar, residual image, light spot

Request repair for external device

A. Video errorVertical / Horizontal bar, residual image, light spot, external device color error

A12

External device screen error-Color error

External Inputerror

Connect other external device and cable(Check normal operation of External Input, Component, RGB and HDMI/DVI by connecting Jig, pattern Generator ,Set-top Box etc.

N

Y

Replace Main B/D

Screennormal?

Check screen condition by input-External Input-Component-RGB-HDMI/DVI

Request repair for external device

Componenterror

RGBerror

HDMI/DVI

Connect other external device and cable(Check normal operation of External Input, Component, RGB and HDMI/DVI by connecting Jig, pattern Generator ,Set-top Box etc.

Replace Main B/D

Screennormal?

NY

Check S/W Version

Y

NCheckversion

S/W Upgrade

Y

NNormalscreen?

End

Y

N

Replace Main B/D

For LGD panel

ReplaceModule

Screennormal?

End

Establisheddate


symptom


A8 A10/ A11

Check Test pattern

A28

For other panel

2010. 12 .14



B. Power errorNo power

Power LEDOn?

Y

N

DC Power onby pressing Power Key On Remote control

Y

NNormal operation?

Check Power On ‘”High”

Check Power cordwas inserted properly

Check Power LED

Replace Power B/D

Measure voltage of each output of Power B/D

N

YNormalvoltage?

Replace Main B/D

N

YOK?

Replace Main B/D

N

Y

Normal?

Check ST-BY 3.5V

Replace Power B/DN

YNormal

voltage?

Replace Power B/D

Y

A17

A18

A19

A4


Establisheddate


symptom

. Stand-By: Red

. Operating: white

※Close

2010. 12 .14



B. Power errorOff when on, off while viewing, power auto on/off

Error?N

Y

Check Power OffMode

Fix A/C cord & Outlet and check each 3 phase out

Check A/C cord

Check for all 3- phasepower out

Check outlet

Replace Main B/DCPUAbnormal

(If Power Off mode is not displayed)Check Power B/D voltage

Y

N

Replace Main B/DNormalvoltage?

Replace Power B/D

Replace Power B/D

N

YNormal? End

※ CautionCheck and fix exterior of Power B/D Part

A22

A19

Establisheddate


symptom


Status Power off List Explanation

Normal

"POWEROFF_REMOTEKEY" Power off by REMOTE CONTROL

"POWEROFF_OFFTIMER" Power off by OFF TIMER

"POWEROFF_SLEEPTIMER" Power off by SLEEP TIMER

"POWEROFF_INSTOP" Power off by INSTOP KEY

"POWEROFF_AUTOOFF" Power off by AUTO OFF

"POWEROFF_ONTIMER" Power off by ON TIMER

"POWEROFF_RS232C" Power off by RS232C

"POWEROFF_RESREC" Power off by Reservated

Record

"POWEROFF_RECEND" Power off by End of Recording

"POWEROFF_SWDOWN" Power off by S/W Download

"POWEROFF_UNKNOWN" Power off by unknown status except listed case

Abnormal"POWEROFF_ABNORMAL1" Power off by abnormal status except CPU trouble

"POWEROFF_CPUABNORMAL" Power off by CPU Abnormal

* Please refer to the all cases whichcan be displayed on power off mode.

Abnormal 1

2010. 12 .14



No audioScreen normal

Check user menu > Speaker off

OffN

Y

Cancel OFF

Check audio B+ 24V of Power Board Normal

voltageY

N

Replace Power Board and repair parts

Check Speaker disconnection

N

Y

Replace Speaker

Replace MAIN Board End

C. Audio errorNo audio/ Normal video

A24 A25

Disconnection

Establisheddate


symptom


2010. 12 .14



→ abnormal audio/discontinuation/noise is same after “Check input signal” compared to No audio

C. Audio errorWrecked audio/ discontinuation/noise

Wrecked audio/Discontinuation/

Noise for all audio

Check and replace speaker and connector


Noise only for D-TV


Noise only for Analog


Noise only for External Input

Connect and check other external device

N

Y

Normalaudio?

Check and fix external device

Replace Power B/D

N

Y

Normalvoltage?

Check input signal-RF-External Input signal

Signal normal?

(When RF signal is not received)Request repair to external cable/ANT provider

Y

Check audio B+ Voltage (24V)

Replace Main B/D

(In case of External Input signal error)Check and fix external device

Replace Main B/DN

End

Establisheddate


symptom


A25

2010. 12 .14



D. General Function ProblemRemote control & Local switch checking

Y

N

1. Remote control(R/C) operating error

Check R/C itself Operation

Normaloperating?

Normaloperating?

Y

Close

Replace R/C

If R/C operate,Explain the customer cause is interferencefrom light in room.

Check R/C OperatingWhen turn off light

in room

Check & ReplaceBaterry of R/C

Check & RepairCable connectionConnector solder

Normaloperating?

Check B+ 3.5VOn Main B/D

A27

NormalVoltage?

Close

N

N

Check 3.5v on Power B/DReplace Power B/D or

Replace Main B/D(Power B/D don’t have problem)

A4

Check IROutput signal

NormalSignal?

N

Y

Repair/ReplaceIR B/D

N

A27

ReplaceMain B/D

YA27


Establisheddate


symptom2010. 12 .14



Check technical information- Fix information- S/W Version

N

Y

Technical information?

Check input signal

Signalinput?

Y

N

External Input andComponent

Recognition error

Check and fix external device/cable

RGB,HDMI/DVI, Optical

Recognition error

Replace Main B/D

Replace Main B/DFix in accordance

with technical information

D. Function errorExternal device recognition error

Establisheddate


symptom


2010. 12 .14



Check location of noise

Identify nose type

Circuit noise

Replace PSU(with LED driver)

Replace LED driver

Mechanical noise

Check location of noise

OR

※ When the nose is severe, replace the module(For models with fix information, upgrade the S/W or provide the description)

※ If there is a “Tak Tak” noise from the cabinet, refer to the KMS fix information and then proceed as shown in the solution manual(For models without any fix information, provide the description)

OR

※ Mechanical noise is a natural phenomenon, and apply the 1st level description. When the customer does not agree, apply the process by stage. ※ Describe the basis of the description in “Part related to nose” in the Owner’s Manual.

E. Noise Circuit noise, mechanical noise

Establisheddate


symptom


2010. 12 .14



Replace moduleZoom part with exterior damage

Moduledamage

Cabinetdamage Replace cabinet

Replace remote controllerRemote

controllerdamage

Standdent Replace stand

F. Exterior defectExterior defect

Adjust VCOM

Establisheddate


symptom


A28

2010. 12 .14



Contents of LCD TV Standard Repair Process Detail Technical Manual

No. Error symptom Content Page Remarks

21

B. Power error_No

power

Check front display LED A17

22 Check power input Voltage & ST-BY 5V A18

23 Checking method when power is ON A19

24 POWER BOARD voltage measuring method A4

25

26B. Power error_Off

when on, off while viewing

POWER OFF MODE checking method A22

27B. Power error_Off

when on, off while viewing

POWER BOARD PIN voltage checking method A19

28

C. Audio error_No

audio/Normal video

Checking method in menu when there is no audio

A24

29Voltage and speaker checking method when there is no audio

A25

30C. Audio error_Wrecked

audio/discontinuation

Voltage and speaker checking method in case of audio error

A25

31D. Function error_ No response in remote controller, key error

Remote controller operation checking method A27

32 D. VCOM Adjustment Sequence of the Vcom

adjustment A28

Continued from previous page



Entry method

1. Press the ADJ button on the remote controller for adjustment.

2. Enter into White Balance of item 6.

3. After recording the R, G, B (GAIN, Cut) value of Color Temp (Cool/Medium/Warm), re- enter the value after replacing the MAIN BOARD.

Standard Repair Process Detail Technical Manual

Check White Balance value

A. Video error_No video/Normal audio

<ALL MODELS>

A4

Established date

Revised date

Error symptom

ContentLCD TV

Entry method

1. Press the ADJ button on the remote controller for adjustment.

2. Enter into White Balance of item 7.

3. After recording the R, G, B (GAIN, Cut) value of Color Temp (Cool/Medium/Warm), re- enter the value after replacing the MAIN BOARD.

2010. 12 .14




Power Board voltage measuring method

A. Video error_No video/ AudioA5

Established date

Revised date

Error symptom

ContentLCD TV

Check the DC 24V, 12V, 3.5V.

24 Pin

(Power Board ↔ Main Board)

SMAW200-H24S (YEONHO)

1 Power on 2 24V

3 24V 4 24V

5 GND 6 GND

7 GND 8 GND

9 3.5V 10 3.5V

11 3.5V 12 3.5V

13 GND 14 GND

15 GND 16 GND

17 12V 18 Inverter On/off

19 12V 20 Lamp : A-Dim

LED : N.C

21 12V 22 PWM Dim #1

23 GND/P_DIM2

• Lamp SCANNING Model

: PWM Dim #2

24 Error-out

Edge LED

2010. 12 .14



MENU - Set up support - signal test- select channel

When the signal is strong, use the attenuator (-10dB, -15dB, -20dB etc.)


TUNER input signal strength checking method

A. Video error_Video error, video lag/stop

<ALL MODELS>

A6

Established date

Revised date

Error symptom

ContentLCD TV 2010. 12 .14




LCD-TV Version checking method


1. Checking method for remote controller for adjustment

Press the IN-START with the remote controller for adjustment

Version

<ALL MODELS>

A7

Established date

Revised date

Error symptom





LCD TV connection diagram (1)

A. Video error _Vertical/Horizontal bar, residual image, light spot

As the part connecting to the external input, check the screen condition by signal

A8

Established date

Revised date

Error symptom

ContentLCD TV

<ALL MODELS>

2010. 12 .14



Checking method: 1. Check the signal strength or check whether the screen is normal when the external device is connected. 2. After measuring each voltage from power supply, finally replace the MAIN BOARD.


TUNER checking part


<ALL MODELS>

A9

Established date

Revised date

Error symptom





Adjustment Test pattern - ADJ Key

A. Video error_Color error

You can view 6 types of patterns using the ADJ Key

Checking item : 1. Defective pixel 2. Residual image 3. MODULE error (ADD-BAR,SCAN BAR..)4.Video error (Classification of MODULE or Main-B/D!)

A12

Established date

Revised date

Error symptom




Solder defect, CNT Broken

T-Con Defect, CNT BrokenT-Con Defect, CNT BrokenT-Con Defect, CNT Broken

Solder defect, CNT Broken Solder defect, CNT Broken

Solder defect, CNT Broken Solder defect, CNT Broken Abnormal Power Section

Solder defect, Short/Crack Abnormal Power Section Solder defect, Short/Crack

Appendix : Exchange T-Con Board (1)



Abnormal Power Section Solder defect, Short/CrackAbnormal Power Section

Solder defect, Short/Crack Fuse Open, Abnormal power section

NoiseGRADATION GRADATION

Abnormal Display

Appendix : Exchange T-Con Board (2)



Appendix : Exchange PSU(LED driver)

No Light Dim Light

Dim Light Dim Light

No picture/Sound Ok



Appendix : Exchange the Module (1)

Panel Mura, Light leakage Press damage

CrosstalkCrosstalk Press damage

Panel Mura, Light leakage

Press damage

Un-repairable CasesIn this case please exchange the module.



Vertical BlockSource TAB IC Defect

Horizontal BlockGate TAB IC Defect

Gate TAB IC Defect Gate TAB IC Defect

Vertical LineSource TAB IC Defect

Vertical BlockSource TAB IC Defect

Horizontal BlockGate TAB IC Defect

Horizontal lineGate TAB IC Defect

Gate TAB IC DefectHorizontal BlockGate TAB IC Defect

Appendix : Exchange the Module (2)

Un-repairable CasesIn this case please exchange the module.




Check front display LED

B. Power error _No powerA17

Established date

Revised date

Error symptom

ContentLCD TV

ST-BY condition: RedPower ON condition: white

Front LED control :Menu Option Power Indicator

Standby light ON

2010. 12 .14




Check power input voltage and ST-BY 5V


Established date

Revised date

Error symptom

ContentLCD TV

For ’10 models, there is no voltage out for st-by purpose. When st-by, only 3.5V is normally on.

Check the DC 20V/24V, 12V, 3.5V.

Edge LED

2010. 12 .14

Edge LED

24 Pin



1 Power on 2 24V

3 24V 4 24V

5 GND 6 GND

7 GND 8 GND

9 3.5V 10 3.5V

11 3.5V 12 3.5V

13 GND 14 GND

15 GND 16 GND



LED : N.C

21 12V 22 PWM Dim #1

23 GND/P_DIM2


: PWM Dim #2

24 Error-out




Checking method when power is ON


Established date

Revised date

Error symptom

ContentLCD TV

Check “power on” pin is high

2010. 12 .14

24 Pin



1 Power on 2 24V

3 24V 4 24V

5 GND 6 GND

7 GND 8 GND

9 3.5V 10 3.5V

11 3.5V 12 3.5V

13 GND 14 GND

15 GND 16 GND



LED : N.C

21 12V 22 PWM Dim #1

23 GND/P_DIM2


: PWM Dim #2

24 Error-out

Edge LED

Edge LED



Entry method

1. Press the IN-START button of the remote controller for adjustment

2. Check the entry into adjustment item 3


POWER OFF MODE checking method

B. Power error _Off when on, off whiling viewing

<ALL MODELS>

A22

Established date

Revised date

Error symptom




Checking method1. Press the MENU button on the remote controller

2. Select the AUDIO function of the Menu

3. Select TV Speaker from Off to On


Checking method in menu when there is no audio

C. Audio error_No audio/Normal video

<ALL MODELS>

A24

Established date

Revised date

Error symptom




Checking order when there is no audio

① Check the contact condition of or 24V connector of Main Board

② Measure the 24V input voltage supplied from Power Board(If there is no input voltage, remove and check the connector)

③ Connect the tester RX1 to the speaker terminal and if you hear the Chik Chik sound when you touch the GND and output terminal, the speaker is normal.


Voltage and speaker checking method when there is no audio

C. Audio error_No audio/Normal video

<ALL MODELS>

A25

Established date

Revised date

Error symptom

ContentLCD TV

①②

③

24 Pin



1 Power on 2 20V (24V)

3 20V (24V) 4 20V (24V)

5 GND 6 GND

7 GND 8 GND

9 3.5V 10 3.5V

11 3.5V 12 3.5V

13 GND 14 GND

15 GND 16 GND



LED : N.C

21 12V 22 PWM Dim #1

23 GND/P_DIM2 24 Error-out

②

2010. 12 .14



Checking order

1, 2. Check IR cable condition between IR & Main board.3. Check the st-by 3.3V on the terminal 6.4. When checking the Pre-Amp when the power is in ON condition, it is normal when the Analog

Tester needle moves slowly, and defective when it does not move at all.


Remote controller operation checking method

D. Function error_ No response in remote controller,key error

<ALL MODELS>

A27

Established date

Revised date

Error symptom

ContentLCD TV

P4102

1 SCL

2 SDA

3 GND

4 KEY1

5 KEY2

6 St 3.5V

7 GND

8 RED_LED

9 IR

10 GND

①

②

③

④

2010. 12 .14




Sequence of the Vcom adjustment

D. VCOM Adjustment

1. Case

LCD module change

T-Con board change

2. Equipment

Service Remote controller

3. Adjust sequence

Press the ‘adj’ key

select V-COM

As pushing the right or the left button on the remote controller, And find the V-COM value Which is no orminimized the Flicker.(If there is no flicker at default value, Press the exit key and finish the VCOM adjustment.)

Push the OK key to store the value. Then the message “Saving OK” is pop.

Press the exit key to finish V-COM adjustment.

A28

Established date

Revised date

Error symptom




32LM660S, 660T, 669S, 669T

Documents

Transcript of 32LM660S, 660T, 669S, 669T