300M MIMO Wireless-N USB Adapter - iBall User Manual.pdf · FCC STATEMENT This equipment has been...

300M MIMO Wireless-N USB Adapter Model No. iB-WUM300N

User Manual

Ver.: 1.0.0

FCC STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to pro-vide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not in-stalled and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the following

measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

Consult the dealer or an experienced radio/ TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two

conditions:

1) This device may not cause harmful interference.

2) This device must accept any interference received, including interference that may

cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment.

CE Mark Warning

This is a class B product. In a domestic environment, this product may cause radio interference, in

which case the user may be required to take adequate measures.

CONTENTS

300M MIMO Wireless-N USB Adapter ...................................................................... I

Model No. iB-WUM300N ............................................................................................ I

Package Contents .................................................................................................... 1

Chapter 1 Introduction ......................................................................................... 2

1.1 Overview of the Product .......................................................................................... 2

1.2 Features ................................................................................................................... 2

1.2.1 Hardware Installation .......................................................................... 2

Please insert the USB Adapter into the USB port of your computer / Laptop ........ 2

1.3 LED Status ............................................................................................................... 2

Chapter 2 Installation Guide ................................................................................ 3

2.1 Hardware Installation ............................................................................................... 3

2.2 Software Installation ................................................................................................ 3

2.2.1 Overview .................................................................................................. 3

2.2.2 Software Installation for Windows XP ...................................................... 3

2.2.3 Software Installation for Windows Vista / 7 .............................................. 6

2.3 Wireless Network Connection under Windows 7 .................................................. 10

Chapter 3 iBallBaton Wireless Utility ................................................................ 12

3.1 Station mode (Client Mode) ................................................................................... 12

3.1.1 Available Networks .................................................................................... 12

3.1.2 Link Information ......................................................................................... 14

3.1.3 Profile Settings ........................................................................................... 15

3.1.4 About ........................................................................................................... 21

3.1.5 Help .............................................................................................................. 21

3.2.1 Config AP .................................................................................................... 21

3.2.2 AP Mode under Windows 7 ....................................................................... 22

Chapter 4 Appendix 2: How to Set WPS ........................................................... 23

Chapter 5 Configuration ..................................................................................... 28

5.1 General Status ....................................................................................................... 28

5.2 Profile Management ............................................................................................... 29

Appendix A: Specifications ................................................................................... 31

Appendix B: Glossary ............................................................................................ 32

AppendixC: Contact Information…………………………………….……………...…26

1

Package Contents

The following items should be found in your package:

iB-WUM300N 300M MIMO Wireless-N USB Adapter

Quick Installation Guide

One Resource CD for iB-WUM300N, including:

Wireless Utility and Drivers

User Guide

Note:

Make sure that the package contains the above items. If any of the listed items are damaged or

missing, please contact with your distributor.

Conventions:

The ‘Adapter’ mentioned in this User Guide stands for iBall Baton iB-WUM300N 300M Wireless-N

USB Adapter without any explanations.


2

Chapter 1 Introduction

Thank you for choosing the iB-WUM300N 300M MIMO Wireless-N USB Adapter.

1.1 Overview of the Product

iBall Baton 300Mbps Wireless-N USB Adapter complies with IEEE 802.11n wireless standards.

MIMO technology provides wireless transmission rates up to 300Mbps.

2T2R Omni-directional Antenna supports better wireless performance, transmission rate and

coverage.

1.2 Features

Complies with IEEE802.11 b/g/n wireless standards

WPS Security - Automatically generates WPA2 Security Authentication

With 64/128-bit WEP, WPA-PSK & WPA2-PSK Wireless security

USB 2.0 High speed Interface

Supports PSP X-Link connection for joyful online gaming experience

Simple Configuration and monitoring utility

OS Compatible: Windows 2000 / XP / Vista / Win7 & MAC OS upto 10.8.2

1.2.1 Hardware Installation

Please insert the USB Adapter into the USB port of your computer / Laptop

1.3 LED Status

Status Working Status

Off The driver has not been installed.

Flashing Slowly Driver installed but there is no data being transmitted or received.

Flashing Quickly There is data being transmitted or received.


3

Chapter 2 Installation Guide

2.1 Hardware Installation

There are two ways to install the Adapter:

1. Plug the Adapter directly to the USB port on your computer.

2. Connect the Adapter and your computer through the USB cable attached in package.

The LED will light up when the Adapter is installed successfully and the PC is on.

2.2 Software Installation

2.2.1 Overview

The Adapter’s Setup Wizard will guide you through the Installation process. The Setup Wizard will

install the Wireless Utility and drivers.

When you install the hardware before installing the software, the system will prompt “Found New

Hardware Wizard”. Click Cancel, and run the Setup Wizard program on the CD-ROM.

The Setup steps for Windows operation Systems are very similar. The User Guide takes the

Windows XP for example to explain the installation.

2.2.2 Software Installation for Windows XP

Step 1: Insert the Resource CD into your CD-ROM drive, and open the folder with the same

name as your product. Then double-click Wizard.exe in the proper folder to start the

installation, and Figure 2-1 will appear. You can click Cancel to end the installation in the

screen. Otherwise, the installation will continue.

Figure 2-1


4

Step 2: Click Next in the screen below (shown in Figure 2-2) to continue, you can click Cancel to

end the installation.

Figure 2-2

Step 3: After that, the next screen will appear Select which option you want to Install to

continue.

Figure 2-3


5

Step 4: In the next screen, the files will be copied as the next screen shows (shown in Figure

2-4). To end the Installation, click Cancel.

Figure 2-4

Note:

During the installation, the system will warn about Windows Logo testing, please click Continue

Anyway to continue the installation.

Figure 2-5


6

Step 5: Click the Finish button to complete the installation.

Figure 2-6

2.2.3 Software Installation for Windows Vista / 7

The Setup steps for Windows Vista and Windows 7 are very similar. The User Guide takes

Windows Vista for example to explain the installation.

1. Insert the Resource CD into your CD-ROM drive, and open the folder with the same name as

your product. Then double-click Setup.exe in the proper folder according to your operating

system to start the installation. And then Figure 2-7 will appear. You can click Cancel to end

the installation in the screen. Otherwise, the installation will continue.

Figure 2-7


7

2. Click I accept and click Next in the screen below to continue, you can click Cancel to end the

Figure 2-8

3. After that, the next screen will appear. Select which option you want to install to continue.

Figure 2-9


8

4. After that, the files will be copied as the next screen shown (shown in Figure 2-10). To end

the Installation, click Cancel.

Figure 2-10

Figure 2-11


9

Note:

During the installation, the system will warn about Windows Security testing, please click “Install

this driver software anyway” to continue the installation

Figure 2-12

5. Click the Finish button to complete the installation

Figure 2-13


10

2.3 Wireless Network Connection under Windows 7

1. Click the wireless connection in the lower right corner of the computer’s desktop to view the

available wireless networks. Select the wireless network you wish to connect and click “Connect”

or double click the wireless network to connect. If you don’t find the specified one, please click the

refresh icon in the upper right corner to update the list.

2. If the wireless network you are connecting is encrypted, you’ll be prompted to enter the key. Click

“Ok” after you enter the correct key.


11

3. It shows “Connected” after successfully connected. You can disconnect it, view its status

or modify the wireless network properties by right click the wireless network


12

Chapter 3 iBallBaton Wireless Utility

When you are installing the driver, select “Install driver and IBall Baton WLAN Config Tool”

and the adapter driver and client utility will be installed. All functions of this adapter can be

configured via IBall Baton’s utility interface (in the following text it is abbreviated as UI).

Select “Start”-“All Programs” -“IBall Baton Wireless”- IBall Baton Wireless Utility”, or click the

“IBall Baton Wireless Utility” shortcut on your PC’s desktop to start the UI.

3.1 Station mode (Client Mode)

Station mode (Client Mode) Overview

It is a common solution to use the wireless network adapter as a client to receive signals.

Main interface for station mode

The function buttons on the top (From L to R) are respectively Site Survey, Link

Information, Profile, Advanced, About, Help, and MiniSize. While the left column

displays Turn On/Off RF, Security /No security, and Signal status.

3.1.1 Available Networks

The “Available Networks” screen displays currently scanned wireless signals and you can click

one to connect the signal. Select one and you may view the AP’s MAC address, wireless mode

(B/G/N), authentication type, and encryption type, or WPS authentication and signal strength.


13

Before you connect to a wireless network, please click the “Rescan” button to update the wireless

network list and select the one you wish to connect, then click the “Connect” icon.

For the networks that are not encrypted, you can directly click “Connect”. However, for the

encrypted wireless networks,a “Profile” dialog will pop up and you must select the corresponding

authentication type and encryption type,and then click the “Next” button to input the correct

key.Please note that this type of connection will not create a profile ,thus next time connect to this

network you still need to select it manually.

The detailed explanations about the authentication and encryption are as follows:

WEP：Supports 10/26-bit Hex characters and 5/13-bit ASCII.

WPA-PSK：Supports 8-63-bit ASCII and 8-64-bit Hex characters.

WPA2-PSK：Supports 8-63-bit ASCII and 8-64-bit Hex characters.

WPA-PSK/WPA2-PSK：Supports 8-63-bit ASCII and 8-64 -bit hex characters.


14

NOTE:

The Hex characters consist of numbers 0~9 and letters a-f.

ASCII characters consist of any letters and characters.

3.1.2 Link Information

After successfully connected to one wireless network, you can view its detailed information

by clicking the “Link Information” on the main interface.

1. “Link Status” screen displays the detailed information of the connected AP including its SSID,MAC

address, authentication type, encryption type, network type and channel.

2. “Throughput” screen displays the signal strength of each of the wireless adapter’s

antennas and the link quality.

3.”Statistics” screen is used to count the total Rx and Tx data packets, including

transmitted,retransmitted and fail to receive ACK after all retries.You can click the “Reset Counter”

button to clear the count.


15

3.1.3 Profile Settings

Except the above common connection type, you can also connect to the wireless network by

adding a profile on the “Profile Settings“screen.The “Profile Settings” screen is used to save the

wireless network parameters. When the adapter is successfully connected to a network, the

profile name of this network will automatically be added here, which helps the adapter to quickly

connect to the wireless network next time. However, there’s one exception that when you have set

the hidden SSID,namely the SSID can not be scanned,then you must manually connect by adding

the profile name.The main interface is as shown below.

Add: create a new profile

Delete: delete the existing profile

Edit: modify the existing profile

Add WPS Profile: WPS setting requires that the connecting wireless device support

WPS function. WPS helps you to fulfill wireless encryption fast as well as secure your wireless

network. For detailed setting steps, refer to appendix2.

There are two network types for your option when clicking the “Add” button to add wireless

adapter connection: Infrastructure and Ad-Hoc.


16

Infrastructure is an application mode that integrates the wired and wireless LAN

architectures. It is different from Ad-Hoc in that in this mode the computer installed with the

wireless network adapter has to fulfill the wireless communication via AP or wireless router. It can

be devided into two modes:“wireless AP + wireless network adapter” and “wireless router +

wireless network adapter”.

Ad-Hoc is a special wireless mobile network application mode. All nodes in the network are

equal.Usually it is used to share resources by connecting the opposing computer ’s wireless

adapter.

1. Infrastructure Profile Management

When you are connecting the wireless adapter to an AP or a wireless router, please select

the Infrastructure mode.

Click the “Add”button and select the network type as”

Infrastructure”,and enter the profile name and SSID or you can find the SSID you wish to

connect from the drop-down list.


17

Click the next button to select the authentication type and encryption type such as WPA－

PSK and AES, and then input the key and click next.

After a profile is successfully added, the profile name can be seen on the profile list,you can

edit , import or export the profile,click “Active” to finish the connection,now you can also view the

detailed connection status on the “Link Information”screen.


18

NOTE:

If the SSID broadcast function of the wireless router or AP you wish to connect is disabled,

then the wireless adapter can not scan the SSID, thus you need to connect by creating the

corresponding profile.

2.Ad-Hoc Profile management

Using the Ad-hoc mode to establish a wireless network requires that each computer should

be equipped with a wireless network adapter. By connecting these wireless adapters, computers

are able to share the resources. The detailed setting steps are as follows:

1）Firstly you’ll have to allocate a static IP to each wireless adapter to be connected in

Ad-hoc mode.

a.Right click “My Network Places” on your computer’s desktop and select “Properties”.

b.Right click “Wireless Network Connection”, and select “Properties”


19

c.Select “Internet Protocol(TCP/IP)”and click “Properties”.

d. Please enter the IP address and subnet mask, and make sure this IP address is not used

by other devices in the network.For example: if your wireless adapter’s IP address is 192.168.0.1，

then set other wireless adapters’ IP addresses within the range of 192.168.0.2

-192.168.0.254.Click “Ok” to save the settings.

2) Create a new Ad-hoc profile

Click the “Add” button and enter the network name in the SSID field to identify the wireless

network, and select Ad-hoc as the network type and then select the channel.


20

Click the “Next” button to select the authentication type and encryption type and then input

the correct key and click “Next”.

After a profile is successfully added,the profile can be seen on the profile list ,select it and

click the “Active” icon on the lower right corner.

And then search for the wireless network on other clients. Double click the wireless network

you have configured and you’ll be prompted for the key .After entering the key, click “Connect”.


21

3.1.4 About

This screen mainly displays the version information of the UI’s different programs as

well as Best IT World (India) Private Limited copyright statement.

3.1.5 Help

To know more about kindly refer the User Manual

3.2.1 Config AP

This screen is used to set the AP’s general parameters including SSID, wireless mode,

channel, authentication type and encryption type, as shown in the picture below.

Here the authentication type is set as “Open” and the encryption type “Not Use”.


22

3.2.2 AP Mode under Windows 7

1. Under Windows 7, wireless adapters are allowed to work in both Station and AP modes.

Here, the wireless adapter acts not only as a client, but also an AP to send wireless signal, which

equals to an amplifier. Right click the UI icon on the lower right corner of the computer desktop

and select “Switch to Station Mode”.

2. You can change the SSID on the Config AP screen and control the number of the connected

clients by modifying the max number of peers. AP mode has only one encryption method which is

WPA2-AES by default and cannot be modified.


23

Chapter 4 Appendix 2: How to Set WPS

WPS setting supports two modes :PBC and PIN. The detailed setting steps are as follows:

1.Wireless Connection in PBC Mode

1.1 Enable the router’s WPS-PBC feature.

If your router provides WPS button, just press and hold it for about 1 second, then the WPS

LED will be flashing for about 2 minutes, which indicates the router’s WPS feature has been

enabled. Otherwise, you can also log on to the router’s web-based utility to enable the PBC mode

in WPS settings screen(For detailed settings,please refer to your router’s user guide).

1.2 Perform PBC connection on the UI of the wireless adapter

1) On the main interface of iBall Baton’s UI, click “Profile Settings”—“Add WPS Profile”.

2) On the Profile List screen, select “Push-Button Configuration”(PBC) and then click the

“Next” button, select “Start PBC” two minutes after the router enables the WPS function. The

connection is established when the negotiating process finishes.


24

Start PBC:

Negotiating process:

A profile forms automatically after the connection is successfully established.

1.3 Using the wireless adapter’s WPS button to perform PBC connection.

If your wireless adapter provides a WPS button,you may use the button to perform PBC

connection.

a).Run the adapter’s UI and switch to STATION mode

b).Two minutes after the router’s WPS-PBC is enabled,press the adapter’s WPS button to

connect in PBC mode.

c).You may view the PBC connection process on the UI’s PBC screen.

2. Wireless Connections in PIN Mode

On the “Add WPS Profile” screen, select “PIN ” as the WPS Method. You may select the

wireless AP to be connected in WPS mode on the WPS AP drop-down List,or select “Auto “and

then click the next button.


25

4.1 Enrollee Mode

The PIN code field lists the adapter’s current PIN code, when you select “Enrollee” as the

Config Mode, you need to copy this PIN code and input it in the PIN code field of the router ’s WPS

setting screen.

Here we take iBall Baton as an example. First enter its WPS configuration screen,enable

WPS settings and select PIN for WPS mode and then input 18686791 in the PIN code field,and

then click the “Save” button. When the WPS indicator of the Router starts flashing,it indicates that

WPS feature is enabled.

Click the next button on the Profile List screen and click “Start PIN” to start the PIN code

negotiation.


26

4.2 Registrar Mode

On the “Add WPS Profile” screen, select the SSID of the AP that need to negotiate in WPS

mode instead of selecting”Auto”.Then select”PIN” as the WPS method and click the next button to

display the folowing screen:

Select “Registrar” as the config mode and enter the router’s PIN code,such as 35475088

that displays on the router’s WPS screen in section 2.1, in the PIN code field here.

Now you can view the SSID ,authenticaiton type,and encrytion type that need to be

negotiated by the WPS in registrar mode.These values can be modified but we recommend using

the default.Here we use the defaut setting and then click the next buton.


27

You can view the negotiation key on the screen below ,but you are not recommended to

modify it,just click the next buton.

Then click “Start PIN” on the screen below to perform WPS connection.


28

Chapter 5 Configuration

300M MIMO Wireless-N USB Adapter iB-WUM300N can be configured by Wireless Utility. This

chapter describes how to configure your 300M MIMO Wireless-N USB Adapter for wireless

connectivity on your Wireless Local Area Network (WLAN) and use the data security encryption

features.

After installing the Adapter, the Adapter’s tray icon will appear in your system tray. It appears

at the bottom of the screen, and shows the signal strength using color and the received signal

strength indication (RSSI).

If the icon is gray, there is no connection.

If the icon is red, there is poor signal strength.

If the icon is yellow, there is poor signal strength.

If the icon is green, there is good signal strength.

If the icon is green, there is excellent signal strength.

Double-click the icon and the 300M Wireless-N USB Adapter will run. You can also run the utility

by clicking the Start > Programs > iBall Baton Wireless > iBall Baton wireless Utility. The

utility provides integrated and easy tool to:

Display current status information

Edit and add configuration profiles

Display current statistics information

The sections below take Windows XP for example to introduce these above capabilities.

5.1 General Status

Choose the tab General as shown in Figure 5-1, the left filed displays the type of the adapter, the

right field displays the status about the connection, including Status, Speed, Type, SSID, Signal

Strength, Link Quality and other IP information.


29

Figure 5-1

Signal Strength - This shows the strength of the wireless signal.

Link Quality - This shows the quality of the wireless connection.

ReNew IP - Click the button to get the IP address from the AP.

Show Tray Icon - Select the option to display the icon on the bottom of the desktop.

Disable Adapter - If you select the option, the adapter can’t work.

Radio Off - If you select the option, the wireless function will be ineffective.

Windows Zero Config - Select the option, you can use the Windows Zero Config function.

Click Close to close the screen.

5.2 Profile Management

Click the tab Profile as shown in Figure 5-2 to add, remove, edit, duplicate or set default for a

profile.


30

Figure 5-2


31

Appendix A: Specifications

Normal

Interface USB 2.0 Interface

Standards IEEE802.11n; IEEE802.11g; IEEE802.11b;

Operating System Windows XP, Windows Vista, Windows 7 & Windows 8

Radio Data Rate 11b：1/2/5.5/11Mbps

11g：6/9/12/18/24/36/48/54Mbps

11n：Up to 300Mbps for receiver

Modulation 11b:CCK,QPSK,BPSK;

11g:OFDM;

11n: QPSK,BPSK,16-QAM,64-QAM

Media Access Protocol CSMA/CA with ACK

Data Security WPA/WPA2; 64/128-bit WEP; TKIP/AES

Frequency 2.4 ~ 2.4835GHz

Spread Spectrum Direct Sequence Spread Spectrum (DSSS)

Safety & Emissions FCC, CE

Environmental and Physical

Operating Temp. 0℃~40℃ (32℉~104℉)

Storage Temp. -40℃~70℃ (-40℉~158℉)

Humidity 10%~95% RH, Non-condensing


32

Appendix B: Glossary

802.11b - The 802.11b standard specifies a wireless product networking at 11 Mbps using

direct-sequence spread-spectrum (DSSS) technology and operating in the unlicensed radio

spectrum at 2.4GHz, and WEP encryption for security. 802.11b networks are also referred to

as Wi-Fi networks.

802.11g - specification for wireless networking at 54 Mbps using direct-sequence

spread-spectrum (DSSS) technology, using OFDM modulation and operating in the

unlicensed radio spectrum at 2.4GHz, and backward compatibility with IEEE 802.11b devices,

and WEP encryption for security.

Ad-hoc Network - An ad-hoc network is a group of computers, each with a Wireless N USB

Adapter, connected as an independent 802.11 wireless LAN. Ad-hoc wireless computers

operate on a peer-to-peer basis, communicating directly with each other without the use of an

access point. Ad-hoc mode is also referred to as an Independent Basic Service Set (IBSS) or

as peer-to-peer mode, and is useful at a departmental scale or SOHO operation.

DSSS (Direct-Sequence Spread Spectrum) - DSSS generates a redundant bit pattern for all

data transmitted. This bit pattern is called a chip (or chipping code). Even if one or more bits

in the chip are damaged during transmission, statistical techniques embedded in the receiver

can recover the original data without the need of retransmission. To an unintended receiver,

DSSS appears as low power wideband noise and is rejected (ignored) by most narrowband

receivers. However, to an intended receiver (i.e. another wireless LAN endpoint), the DSSS

signal is recognized as the only valid signal, and interference is inherently rejected (ignored).

FHSS (Frequency Hopping Spread Spectrum) - FHSS continuously changes (hops) the

carrier frequency of a conventional carrier several times per second according to a

pseudo-random set of channels. Because a fixed frequency is not used, and only the

transmitter and receiver know the hop patterns, interception of FHSS is extremely difficult.

Infrastructure Network - An infrastructure network is a group of computers or other devices,

each with a Wireless N USB Adapter, connected as an 802.11 wireless LAN. In infrastructure

mode, the wireless devices communicate with each other and to a wired network by first

going through an access point. An infrastructure wireless network connected to a wired

network is referred to as a Basic Service Set (BSS). A set of two or more BSS in a single

network is referred to as an Extended Service Set (ESS). Infrastructure mode is useful at a

corporation scale, or when it is necessary to connect the wired and wireless networks.

Spread Spectrum - Spread Spectrum technology is a wideband radio frequency technique

developed by the military for use in reliable, secure, mission-critical communications systems.

It is designed to trade off bandwidth efficiency for reliability, integrity, and security. In other

words, more bandwidth is consumed than in the case of narrowband transmission, but the

trade off produces a signal that is, in effect, louder and thus easier to detect, provided that the

receiver knows the parameters of the spread-spectrum signal being broadcast. If a receiver is

not tuned to the right frequency, a spread-spectrum signal looks like background noise.

There are two main alternatives, DSSS and FHSS.


33

SSID - A Service Set Identification is a thirty-two character (maximum) alphanumeric key

identifying a wireless local area network. For the wireless devices in a network to

communicate with each other, all devices must be configured with the same SSID. This is

typically the configuration parameter for a wireless PC card. It corresponds to the ESSID in

the wireless Access Point and to the wireless network name. See also Wireless Network

Name and ESSID.

WEP (Wired Equivalent Privacy) - A data privacy mechanism based on a 64-bit or 128-bit or

152-bit shared key algorithm, as described in the IEEE 802.11 standard.

Wi-Fi - A trade name for the 802.11b wireless networking standard, given by the Wireless

Ethernet Compatibility Alliance (WECA, see http://www.wi-fi.net), an industry standards

group promoting interoperability among 802.11b devices.

WLAN (Wireless Local Area Network) - A group of computers and associated devices

communicate with each other wirelessly, which network serving users are limited in a local

area.

WPA (Wi-Fi Protected Access) - A wireless security protocol use TKIP (Temporal Key

Integrity Protocol) encryption, which can be used in conjunction with a RADIUS server.

COPYRIGHT & TRADEMARKS

Specifications are subject to change without notice. iBall Baton is a registered trademark of Best

IT World (India) Pvt. Ltd. Other brands and product names are trademarks or registered

trademarks of their respective holders.

No part of the specifications may be reproduced in any form or by any means or used to make any

derivative such as translation, transformation, or adaptation without permission from Best IT

World (India) Pvt. Ltd. All rights reserved.

Note: For any technical help on iBall Baton products please contact [email protected]

www.iBallBaton.com

mailto:[email protected]

http://www.iballbaton.com/

300M MIMO Wireless-N USB Adapter - iBall User Manual.pdf · FCC STATEMENT This equipment has been...

Documents

Transcript of 300M MIMO Wireless-N USB Adapter - iBall User Manual.pdf · FCC STATEMENT This equipment has been...